From: sibis@codeaurora.org
To: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>,
Jeffrey Hugo <jhugo@codeaurora.org>,
Rob Herring <robh+dt@kernel.org>,
Jonathan Marek <jonathan@marek.ca>,
Ohad Ben-Cohen <ohad@wizery.com>,
Mark Rutland <mark.rutland@arm.com>,
p.zabel@pengutronix.de, MSM <linux-arm-msm@vger.kernel.org>,
linux-remoteproc@vger.kernel.org,
DTML <devicetree@vger.kernel.org>,
lkml <linux-kernel@vger.kernel.org>,
Andy Gross <agross@kernel.org>
Subject: Re: [PATCH 14/16] arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes
Date: Tue, 19 Nov 2019 12:29:31 +0000 [thread overview]
Message-ID: <0101016e83a3aae0-2f25d2f3-6014-4992-9b40-d8716962215b-000000@us-west-2.amazonses.com> (raw)
In-Reply-To: <CAOCk7Nr=Up1LP+-XB7tnoM=XwK+YysDMq8EqyhCLx=WA+eW9PA@mail.gmail.com>
On 2019-11-19 03:37, Jeffrey Hugo wrote:
> On Mon, Nov 18, 2019 at 2:45 PM Sibi Sankar <sibis@codeaurora.org>
> wrote:
>>
>> This patch adds ADSP, MPSS and SLPI nodes for MSM8998 SoCs.
>>
>> Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
>> ---
>> arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 8 ++
>> arch/arm64/boot/dts/qcom/msm8998.dtsi | 122
>> ++++++++++++++++++++++
>> 2 files changed, 130 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
>> b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
>> index 5f101a20a20a2..29e0c2e988e4b 100644
>> --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
>> @@ -23,6 +23,14 @@
>> };
>> };
>>
>> +&adsp_pas {
>> + status = "okay";
>> +};
>> +
>> +&slpi_pas {
>
> "b" comes before "s", no?
will re-order it in the next
re-spin.
>
>> + status = "okay";
>> +};
>> +
>> &blsp1_uart3 {
>> status = "okay";
>>
>> diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi
>> b/arch/arm64/boot/dts/qcom/msm8998.dtsi
>> index 707673e3cf28a..dd1dc35e87b63 100644
>> --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
>> @@ -337,6 +337,73 @@
>> };
>> };
>>
>> + adsp_pas: remoteproc-adsp {
>> + compatible = "qcom,msm8998-adsp-pas";
>> +
>> + interrupts-extended = <&intc GIC_SPI 162
>> IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 0
>> IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 1
>> IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 2
>> IRQ_TYPE_EDGE_RISING>,
>> + <&adsp_smp2p_in 3
>> IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog", "fatal", "ready",
>> + "handover", "stop-ack";
>> +
>> + clocks = <&xo>;
>> + clock-names = "xo";
>> +
>> + memory-region = <&adsp_mem>;
>> +
>> + qcom,smem-states = <&adsp_smp2p_out 0>;
>> + qcom,smem-state-names = "stop";
>> +
>> + power-domains = <&rpmpd MSM8998_VDDCX>;
>> + power-domain-names = "cx";
>> +
>> + status = "disabled";
>> +
>> + glink-edge {
>> + interrupts = <GIC_SPI 157
>> IRQ_TYPE_EDGE_RISING>;
>> + label = "lpass";
>> + qcom,remote-pid = <2>;
>> + mboxes = <&apcs_glb 9>;
>> + };
>> + };
>> +
>> + slpi_pas: remoteproc-slpi {
>> + compatible = "qcom,msm8998-slpi-pas";
>> +
>> + interrupts-extended = <&intc GIC_SPI 390
>> IRQ_TYPE_EDGE_RISING>,
>> + <&slpi_smp2p_in 0
>> IRQ_TYPE_EDGE_RISING>,
>> + <&slpi_smp2p_in 1
>> IRQ_TYPE_EDGE_RISING>,
>> + <&slpi_smp2p_in 2
>> IRQ_TYPE_EDGE_RISING>,
>> + <&slpi_smp2p_in 3
>> IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog", "fatal", "ready",
>> + "handover", "stop-ack";
>> +
>> + px-supply = <&vreg_lvs2a_1p8>;
>> +
>> + clocks = <&xo>,
>> + <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
>> + clock-names = "xo", "aggre2";
>> +
>> + memory-region = <&slpi_mem>;
>> +
>> + qcom,smem-states = <&slpi_smp2p_out 0>;
>> + qcom,smem-state-names = "stop";
>> +
>> + power-domains = <&rpmpd MSM8998_SSCCX>;
>> + power-domain-names = "ssc_cx";
>> +
>> + status = "disabled";
>> +
>> + glink-edge {
>> + interrupts = <GIC_SPI 179
>> IRQ_TYPE_EDGE_RISING>;
>> + label = "dsps";
>> + qcom,remote-pid = <3>;
>> + mboxes = <&apcs_glb 27>;
>> + };
>> + };
>> +
>> tcsr_mutex: hwlock {
>> compatible = "qcom,tcsr-mutex";
>> syscon = <&tcsr_mutex_regs 0 0x1000>;
>> @@ -1048,6 +1115,61 @@
>> #interrupt-cells = <0x2>;
>> };
>>
>> + mss_pil: remoteproc@4080000 {
>> + compatible = "qcom,msm8998-mss-pil";
>> + reg = <0x04080000 0x100>, <0x04180000 0x20>;
>> + reg-names = "qdsp6", "rmb";
>> +
>> + interrupts-extended =
>> + <&intc GIC_SPI 448
>> IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 0
>> IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 1
>> IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 2
>> IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 3
>> IRQ_TYPE_EDGE_RISING>,
>> + <&modem_smp2p_in 7
>> IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog", "fatal", "ready",
>> + "handover", "stop-ack",
>> + "shutdown-ack";
>> +
>> + clocks = <&xo>,
>> + <&gcc GCC_MSS_CFG_AHB_CLK>,
>> + <&gcc GCC_BIMC_MSS_Q6_AXI_CLK>,
>> + <&gcc GCC_BOOT_ROM_AHB_CLK>,
>> + <&gcc GCC_MSS_GPLL0_DIV_CLK_SRC>,
>> + <&gcc GCC_MSS_SNOC_AXI_CLK>,
>> + <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
>> + <&rpmcc RPM_SMD_QDSS_CLK>;
>> + clock-names = "xo", "iface", "bus", "mem",
>> "gpll0_mss",
>> + "snoc_axi", "mnoc_axi", "qdss";
>> +
>> + qcom,smem-states = <&modem_smp2p_out 0>;
>> + qcom,smem-state-names = "stop";
>> +
>> + resets = <&gcc GCC_MSS_RESTART>;
>> + reset-names = "mss_restart";
>> +
>> + qcom,halt-regs = <&tcsr_mutex_regs 0x23000
>> 0x25000 0x24000>;
>> +
>> + power-domains = <&rpmpd MSM8998_VDDCX>,
>> + <&rpmpd MSM8998_VDDMX>;
>> + power-domain-names = "cx", "mx";
>> +
>> + mba {
>> + memory-region = <&mba_mem>;
>> + };
>> +
>> + mpss {
>> + memory-region = <&mpss_mem>;
>> + };
>> +
>> + glink-edge {
>> + interrupts = <GIC_SPI 452
>> IRQ_TYPE_EDGE_RISING>;
>> + label = "modem";
>> + qcom,remote-pid = <1>;
>> + mboxes = <&apcs_glb 15>;
>> + };
>> + };
>> +
>> stm: stm@6002000 {
>> compatible = "arm,coresight-stm",
>> "arm,primecell";
>> reg = <0x06002000 0x1000>,
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
>> Forum,
>> a Linux Foundation Collaborative Project
>>
next prev parent reply other threads:[~2019-11-19 12:29 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20191118214250.14002-1-sibis@codeaurora.org>
2019-11-18 21:43 ` [PATCH 01/16] remoteproc: q6v5-mss: fixup MSM8998 MSS out of reset sequence Sibi Sankar
2019-11-18 21:54 ` Jeffrey Hugo
2019-11-19 15:25 ` Sibi Sankar
[not found] ` <0101016e844504f1-d8bd27a5-c0bf-4b0b-8301-7bd8a890be80-000000@us-west-2.amazonses.com>
2019-11-19 15:43 ` Jeffrey Hugo
2019-11-20 12:01 ` Sibi Sankar
2019-11-18 21:43 ` [PATCH 02/16] remoteproc: q6v5-mss: Streamline the " Sibi Sankar
2019-11-18 21:43 ` [PATCH 03/16] dt-bindings: remoteproc: qcom: Add Q6V5 Modem PIL binding for SC7180 Sibi Sankar
2019-11-22 23:12 ` Rob Herring
2019-11-18 21:43 ` [PATCH 04/16] remoteproc: mss: q6v5-mss: Add modem support on SC7180 Sibi Sankar
2019-11-18 21:43 ` [PATCH 05/16] remoteproc: qcom: pas: Disable interrupt on clock enable failure Sibi Sankar
2019-11-18 21:43 ` [PATCH 06/16] dt-bindings: remoteproc: qcom: Add power-domain bindings for Q6V5 PAS Sibi Sankar
2019-11-22 23:15 ` Rob Herring
2019-11-18 21:43 ` [PATCH 07/16] remoteproc: qcom: pas: Vote for active/proxy power domains Sibi Sankar
2019-11-18 21:43 ` [PATCH 08/16] dt-bindings: remoteproc: qcom: Add ADSP and SLPI support for MSM8998 SoC Sibi Sankar
2019-12-03 22:01 ` Rob Herring
2019-11-18 21:43 ` [PATCH 09/16] remoteproc: qcom: pas: Add MSM8998 ADSP and SLPI support Sibi Sankar
2019-11-18 21:43 ` [PATCH 10/16] dt-bindings: remoteproc: qcom: SM8150 Add ADSP, CDSP, MPSS " Sibi Sankar
2019-12-03 22:02 ` Rob Herring
2019-11-18 21:43 ` [PATCH 11/16] remoteproc: qcom: pas: Add SM8150 ADSP, CDSP, Modem " Sibi Sankar
2019-11-18 21:44 ` [PATCH 12/16] remoteproc: qcom: pas: Add auto_boot flag Sibi Sankar
2019-11-18 21:44 ` [PATCH 13/16] arm64: dts: qcom: msm8998: Update reserved memory map Sibi Sankar
2019-11-18 22:04 ` Jeffrey Hugo
2019-11-19 12:28 ` sibis
2019-11-18 21:44 ` [PATCH 14/16] arm64: dts: qcom: msm8998: Add ADSP, MPSS and SLPI nodes Sibi Sankar
2019-11-18 22:07 ` Jeffrey Hugo
2019-11-19 12:29 ` sibis [this message]
2019-11-18 21:44 ` [PATCH 15/16] arm64: dts: qcom: sm8150: Add ADSP, CDSP, MPSS and SLPI smp2p Sibi Sankar
2019-11-18 21:44 ` [PATCH 16/16] arm64: dts: qcom: sm8150: Add ADSP, CDSP, MPSS and SLPI remoteprocs Sibi Sankar
2019-12-17 0:19 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0101016e83a3aae0-2f25d2f3-6014-4992-9b40-d8716962215b-000000@us-west-2.amazonses.com \
--to=sibis@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=jhugo@codeaurora.org \
--cc=jonathan@marek.ca \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=ohad@wizery.com \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).