From: <Sergiu.Moga@microchip.com>
To: <krzysztof.kozlowski@canonical.com>, <robh+dt@kernel.org>,
<Nicolas.Ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<Claudiu.Beznea@microchip.com>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-i2c@vger.kernel.org>
Subject: Re: [PATCH 2/3] dt-bindings: i2c: convert i2c-at91 to json-schema
Date: Thu, 10 Mar 2022 10:33:57 +0000 [thread overview]
Message-ID: <0a35f2ae-0c89-1859-0375-de4fb3a1ab3d@microchip.com> (raw)
In-Reply-To: <4ebce779-63f5-a7b4-6cd7-5152ce345531@canonical.com>
On 10.03.2022 09:21, Krzysztof Kozlowski wrote:
> On 09/03/2022 13:07, Sergiu Moga wrote:
>> Convert I2C binding for Atmel/Microchip SoCs to Device Tree Schema
>> format.
>>
>> Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
>> ---
>> .../bindings/i2c/atmel,at91sam-i2c.yaml | 144 ++++++++++++++++++
>> .../devicetree/bindings/i2c/i2c-at91.txt | 82 ----------
>> 2 files changed, 144 insertions(+), 82 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>> delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-at91.txt
>>
>> diff --git a/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>> new file mode 100644
>> index 000000000000..d4aadbbd1a11
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
>> @@ -0,0 +1,144 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +# Copyright (C) 2022 Microchip Technology, Inc. and its subsidiaries
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/i2c/atmel,at91sam-i2c.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: I2C for Atmel/Microchip platforms
>> +
>> +maintainers:
>> + - Alexandre Belloni <alexandre.belloni@bootlin.com>
>> +
>> +allOf:
>> + - $ref: "i2c-controller.yaml"
>> + - if:
> allOf with additional if: goes by convention after required:.
>
Understood. I will move the `allOf` after `required:`.
>> + properties:
>> + compatible:
>> + contains:
>> + enum:
>> + - atmel,sama5d4-i2c
>> + - atmel,sama5d2-i2c
>> + - microchip,sam9x60-i2c
>> + then:
>> + properties:
>> + i2c-sda-hold-time-ns:
>> + description:
>> + TWD hold time
>> + maxItems: 1
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - atmel,at91rm9200-i2c
>> + - atmel,at91sam9261-i2c
>> + - atmel,at91sam9260-i2c
>> + - atmel,at91sam9g20-i2c
>> + - atmel,at91sam9g10-i2c
>> + - atmel,at91sam9x5-i2c
>> + - atmel,sama5d4-i2c
>> + - atmel,sama5d2-i2c
>> + - microchip,sam9x60-i2c
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + "#address-cells":
>> + const: 1
>> +
>> + "#size-cells":
>> + const: 0
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + clock-frequency:
>> + default: 100000
>> +
>> + dmas:
>> + items:
>> + - description: TX DMA Channel Specifier
>> + - description: RX DMA Channel Specifier
>> +
>> + dma-names:
>> + items:
>> + - const: tx
>> + - const: rx
>> +
>> + atmel,fifo-size:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description: |
>> + Maximum number of data the RX and TX FIFOs can store for
>> + FIFO capable I2C controllers.
>> +
>> + scl-gpios: true
>> +
>> + sda-gpios: true
>> +
>> + pinctrl:
>> + description: |
>> + Add extra pinctrl to configure i2c pins to gpio function for i2c
>> + bus recovery, call it "gpio" state
> This is a generic property, you do not need it.
>
Will remove it in the next version. Thank you.
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> + - "#address-cells"
>> + - "#size-cells"
>> + - clocks
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/interrupt-controller/irq.h>
>> + #include <dt-bindings/dma/at91.h>
>> + #include <dt-bindings/gpio/gpio.h>
>> +
>> + i2c0: i2c@fff84000 {
>> + compatible = "atmel,at91sam9g20-i2c";
>> + reg = <0xfff84000 0x100>;
>> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&twi0_clk>;
>> + clock-frequency = <400000>;
>> +
>> + eeprom@50 {
>> + compatible = "atmel,24c512";
>> + reg = <0x50>;
>> + pagesize = <128>;
>> + };
>> + };
>> +
>> + i2c1: i2c@f8034600 {
>> + compatible = "atmel,sama5d2-i2c";
>> + reg = <0xf8034600 0x100>;
>> + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
>> + dmas = <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
>> + AT91_XDMAC_DT_PERID(11)>,
>> + <&dma0
>> + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
>> + AT91_XDMAC_DT_PERID(12)>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&flx0>;
>> + atmel,fifo-size = <16>;
>> + i2c-sda-hold-time-ns = <336>;
>> + pinctrl-names = "default", "gpio";
>> + pinctrl-0 = <&pinctrl_i2c0>;
>> + pinctrl-1 = <&pinctrl_i2c0_gpio>;
>> + sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
>> + scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>> +
>> + eeprom@1a {
>> + compatible = "wm8731";
> It seems this is undocumented compatible. Could you use something else,
> documented?
>
I will replace it with a node with a documented compatible in the next
version.
> Best regards,
> Krzysztof
Thank you for the feedback.
Sergiu
next prev parent reply other threads:[~2022-03-10 10:34 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-09 12:07 [PATCH 0/3] dt-bindings: i2c: convert i2c-at91 to json-schema Sergiu Moga
2022-03-09 12:07 ` [PATCH 1/3] ARM: dts: at91: sama7g5: Swap `rx` and `tx` for `i2c` nodes Sergiu Moga
2022-03-09 13:11 ` Tudor.Ambarus
2022-03-09 12:07 ` [PATCH 2/3] dt-bindings: i2c: convert i2c-at91 to json-schema Sergiu Moga
2022-03-09 22:20 ` Rob Herring
2022-03-10 7:21 ` Krzysztof Kozlowski
2022-03-10 10:33 ` Sergiu.Moga [this message]
2022-03-09 12:07 ` [PATCH 3/3] dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list Sergiu Moga
2022-03-10 7:22 ` Krzysztof Kozlowski
2022-03-10 10:42 ` Sergiu.Moga
2022-03-10 11:05 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0a35f2ae-0c89-1859-0375-de4fb3a1ab3d@microchip.com \
--to=sergiu.moga@microchip.com \
--cc=Claudiu.Beznea@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski@canonical.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).