[PATCH v5 0/7] arm64: Default to 32-bit wide ZONE_DMA

[PATCH v5 0/7] arm64: Default to 32-bit wide ZONE_DMA

[Nicolas Saenz Julienne]

Using two distinct DMA zones turned out to be problematic. Here's an
attempt go back to a saner default.

I tested this on both a RPi4 and QEMU.

---

Changes since v4:
 - Fix of_dma_get_max_cpu_address() so it returns the last addressable
   addres, not the limit

Changes since v3:
 - Drop patch adding define in dma-mapping
 - Address small review changes
 - Update Ard's patch
 - Add new patch removing examples from mmzone.h

Changes since v2:
 - Introduce Ard's patch
 - Improve OF dma-ranges parsing function
 - Add unit test for OF function
 - Address small changes
 - Move crashkernel reservation later in boot process

Changes since v1:
 - Parse dma-ranges instead of using machine compatible string

Ard Biesheuvel (1):
  arm64: mm: Set ZONE_DMA size based on early IORT scan

Nicolas Saenz Julienne (6):
  arm64: mm: Move reserve_crashkernel() into mem_init()
  arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
  of/address: Introduce of_dma_get_max_cpu_address()
  of: unittest: Add test for of_dma_get_max_cpu_address()
  arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
  mm: Remove examples from enum zone_type comment

 arch/arm64/mm/init.c      | 16 ++++++------
 drivers/acpi/arm64/iort.c | 52 +++++++++++++++++++++++++++++++++++++++
 drivers/of/address.c      | 42 +++++++++++++++++++++++++++++++
 drivers/of/unittest.c     | 18 ++++++++++++++
 include/linux/acpi_iort.h |  4 +++
 include/linux/mmzone.h    | 20 ---------------
 include/linux/of.h        |  7 ++++++
 7 files changed, 130 insertions(+), 29 deletions(-)

-- 
2.29.0

[PATCH v5 1/7] arm64: mm: Move reserve_crashkernel() into mem_init()

[Nicolas Saenz Julienne]

crashkernel might reserve memory located in ZONE_DMA. We plan to delay
ZONE_DMA's initialization after unflattening the devicetree and ACPI's
boot table initialization, so move it later in the boot process.
Specifically into mem_init(), this is the last place crashkernel will be
able to reserve the memory before the page allocator kicks in. There
isn't any apparent reason for doing this earlier.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
---
 arch/arm64/mm/init.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index 095540667f0f..fc4ab0d6d5d2 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -386,8 +386,6 @@ void __init arm64_memblock_init(void)
 	else
 		arm64_dma32_phys_limit = PHYS_MASK + 1;
 
-	reserve_crashkernel();
-
 	reserve_elfcorehdr();
 
 	high_memory = __va(memblock_end_of_DRAM() - 1) + 1;
@@ -508,6 +506,8 @@ void __init mem_init(void)
 	else
 		swiotlb_force = SWIOTLB_NO_FORCE;
 
+	reserve_crashkernel();
+
 	set_max_mapnr(max_pfn - PHYS_PFN_OFFSET);
 
 #ifndef CONFIG_SPARSEMEM_VMEMMAP
-- 
2.29.0

[PATCH v5 2/7] arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()

[Nicolas Saenz Julienne]

zone_dma_bits's initialization happens earlier that it's actually
needed, in arm64_memblock_init(). So move it into the more suitable
zone_sizes_init().

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
---
 arch/arm64/mm/init.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index fc4ab0d6d5d2..410721fc4fc0 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -190,6 +190,8 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max)
 	unsigned long max_zone_pfns[MAX_NR_ZONES]  = {0};
 
 #ifdef CONFIG_ZONE_DMA
+	zone_dma_bits = ARM64_ZONE_DMA_BITS;
+	arm64_dma_phys_limit = max_zone_phys(zone_dma_bits);
 	max_zone_pfns[ZONE_DMA] = PFN_DOWN(arm64_dma_phys_limit);
 #endif
 #ifdef CONFIG_ZONE_DMA32
@@ -376,11 +378,6 @@ void __init arm64_memblock_init(void)
 
 	early_init_fdt_scan_reserved_mem();
 
-	if (IS_ENABLED(CONFIG_ZONE_DMA)) {
-		zone_dma_bits = ARM64_ZONE_DMA_BITS;
-		arm64_dma_phys_limit = max_zone_phys(ARM64_ZONE_DMA_BITS);
-	}
-
 	if (IS_ENABLED(CONFIG_ZONE_DMA32))
 		arm64_dma32_phys_limit = max_zone_phys(32);
 	else
-- 
2.29.0

[PATCH v5 3/7] of/address: Introduce of_dma_get_max_cpu_address()

[Nicolas Saenz Julienne]

Introduce of_dma_get_max_cpu_address(), which provides the highest CPU
physical address addressable by all DMA masters in the system. It's
specially useful for setting memory zones sizes at early boot time.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>

---

Changes since v4:
 - Return max address, not address limit (one-off difference)

Changes since v3:
 - use u64 with cpu_end

Changes since v2:
 - Use PHYS_ADDR_MAX
 - return phys_dma_t
 - Rename function
 - Correct subject
 - Add support to start parsing from an arbitrary device node in order
   for the function to work with unit tests

 drivers/of/address.c | 42 ++++++++++++++++++++++++++++++++++++++++++
 include/linux/of.h   |  7 +++++++
 2 files changed, 49 insertions(+)

diff --git a/drivers/of/address.c b/drivers/of/address.c
index eb9ab4f1e80b..09c0af7fd1c4 100644
--- a/drivers/of/address.c
+++ b/drivers/of/address.c
@@ -1024,6 +1024,48 @@ int of_dma_get_range(struct device_node *np, const struct bus_dma_region **map)
 }
 #endif /* CONFIG_HAS_DMA */
 
+/**
+ * of_dma_get_max_cpu_address - Gets highest CPU address suitable for DMA
+ * @np: The node to start searching from or NULL to start from the root
+ *
+ * Gets the highest CPU physical address that is addressable by all DMA masters
+ * in the sub-tree pointed by np, or the whole tree if NULL is passed. If no
+ * DMA constrained device is found, it returns PHYS_ADDR_MAX.
+ */
+phys_addr_t __init of_dma_get_max_cpu_address(struct device_node *np)
+{
+	phys_addr_t max_cpu_addr = PHYS_ADDR_MAX;
+	struct of_range_parser parser;
+	phys_addr_t subtree_max_addr;
+	struct device_node *child;
+	struct of_range range;
+	const __be32 *ranges;
+	u64 cpu_end = 0;
+	int len;
+
+	if (!np)
+		np = of_root;
+
+	ranges = of_get_property(np, "dma-ranges", &len);
+	if (ranges && len) {
+		of_dma_range_parser_init(&parser, np);
+		for_each_of_range(&parser, &range)
+			if (range.cpu_addr + range.size > cpu_end)
+				cpu_end = range.cpu_addr + range.size - 1;
+
+		if (max_cpu_addr > cpu_end)
+			max_cpu_addr = cpu_end;
+	}
+
+	for_each_available_child_of_node(np, child) {
+		subtree_max_addr = of_dma_get_max_cpu_address(child);
+		if (max_cpu_addr > subtree_max_addr)
+			max_cpu_addr = subtree_max_addr;
+	}
+
+	return max_cpu_addr;
+}
+
 /**
  * of_dma_is_coherent - Check if device is coherent
  * @np:	device node
diff --git a/include/linux/of.h b/include/linux/of.h
index 5d51891cbf1a..9ed5b8532c30 100644
--- a/include/linux/of.h
+++ b/include/linux/of.h
@@ -558,6 +558,8 @@ int of_map_id(struct device_node *np, u32 id,
 	       const char *map_name, const char *map_mask_name,
 	       struct device_node **target, u32 *id_out);
 
+phys_addr_t of_dma_get_max_cpu_address(struct device_node *np);
+
 #else /* CONFIG_OF */
 
 static inline void of_core_init(void)
@@ -995,6 +997,11 @@ static inline int of_map_id(struct device_node *np, u32 id,
 	return -EINVAL;
 }
 
+static inline phys_addr_t of_dma_get_max_cpu_address(struct device_node *np)
+{
+	return PHYS_ADDR_MAX;
+}
+
 #define of_match_ptr(_ptr)	NULL
 #define of_match_node(_matches, _node)	NULL
 #endif /* CONFIG_OF */
-- 
2.29.0

[PATCH v5 4/7] of: unittest: Add test for of_dma_get_max_cpu_address()

[Nicolas Saenz Julienne]

Introduce a test for of_dma_get_max_cup_address(), it uses the same DT
data as the rest of dma-ranges unit tests.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>

---
Changes since v3:
 - Remove HAS_DMA guards

 drivers/of/unittest.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/of/unittest.c b/drivers/of/unittest.c
index 06cc988faf78..b9a4d047a95e 100644
--- a/drivers/of/unittest.c
+++ b/drivers/of/unittest.c
@@ -869,6 +869,23 @@ static void __init of_unittest_changeset(void)
 #endif
 }
 
+static void __init of_unittest_dma_get_max_cpu_address(void)
+{
+	struct device_node *np;
+	phys_addr_t cpu_addr;
+
+	np = of_find_node_by_path("/testcase-data/address-tests");
+	if (!np) {
+		pr_err("missing testcase data\n");
+		return;
+	}
+
+	cpu_addr = of_dma_get_max_cpu_address(np);
+	unittest(cpu_addr == 0x50000000,
+		 "of_dma_get_max_cpu_address: wrong CPU addr %pad (expecting %x)\n",
+		 &cpu_addr, 0x50000000);
+}
+
 static void __init of_unittest_dma_ranges_one(const char *path,
 		u64 expect_dma_addr, u64 expect_paddr)
 {
@@ -3266,6 +3283,7 @@ static int __init of_unittest(void)
 	of_unittest_changeset();
 	of_unittest_parse_interrupts();
 	of_unittest_parse_interrupts_extended();
+	of_unittest_dma_get_max_cpu_address();
 	of_unittest_parse_dma_ranges();
 	of_unittest_pci_dma_ranges();
 	of_unittest_match_node();
-- 
2.29.0

[PATCH v5 5/7] arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges

[Nicolas Saenz Julienne]

We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)

The DMA layer also needs to be able to allocate memory that is
guaranteed to meet those DMA constraints, for bounce buffering as well
as allocating the backing for consistent mappings. This is why the 1 GB
ZONE_DMA was introduced recently. Unfortunately, it turns out the having
a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and
potentially in other places where allocations cannot cross zone
boundaries. Therefore, we should avoid having two separate DMA zones
when possible.

So, with the help of of_dma_get_max_cpu_address() get the topmost
physical address accessible to all DMA masters in system and use that
information to fine-tune ZONE_DMA's size. In the absence of addressing
limited masters ZONE_DMA will span the whole 32-bit address space,
otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit
address space, and have ZONE_DMA32 cover the rest of the 32-bit address
space.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>

---

Changes since v4:
 - Use fls64 as we're now using the max address (as opposed to the
   limit)

Changes since v3:
 - Simplify code for readability.

Changes since v2:
 - Updated commit log by shamelessly copying Ard's ACPI commit log

 arch/arm64/mm/init.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index 410721fc4fc0..a2ce8a9a71a6 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -42,8 +42,6 @@
 #include <asm/tlb.h>
 #include <asm/alternative.h>
 
-#define ARM64_ZONE_DMA_BITS	30
-
 /*
  * We need to be able to catch inadvertent references to memstart_addr
  * that occur (potentially in generic code) before arm64_memblock_init()
@@ -188,9 +186,11 @@ static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
 static void __init zone_sizes_init(unsigned long min, unsigned long max)
 {
 	unsigned long max_zone_pfns[MAX_NR_ZONES]  = {0};
+	unsigned int __maybe_unused dt_zone_dma_bits;
 
 #ifdef CONFIG_ZONE_DMA
-	zone_dma_bits = ARM64_ZONE_DMA_BITS;
+	dt_zone_dma_bits = fls64(of_dma_get_max_cpu_address(NULL));
+	zone_dma_bits = min(32U, dt_zone_dma_bits);
 	arm64_dma_phys_limit = max_zone_phys(zone_dma_bits);
 	max_zone_pfns[ZONE_DMA] = PFN_DOWN(arm64_dma_phys_limit);
 #endif
-- 
2.29.0

[PATCH v5 6/7] arm64: mm: Set ZONE_DMA size based on early IORT scan

[Nicolas Saenz Julienne]

From: Ard Biesheuvel <ardb@kernel.org>

We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)

Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.

This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.

So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
[nsaenz: Rebased, removed documentation change and add declaration in acpi_iort.h]
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>

---

Changes since v3:
 - Use min_not_zero()
 - Check revision
 - Remove unnecessary #ifdef in zone_sizes_init()
 
 arch/arm64/mm/init.c      |  3 ++-
 drivers/acpi/arm64/iort.c | 52 +++++++++++++++++++++++++++++++++++++++
 include/linux/acpi_iort.h |  4 +++
 3 files changed, 58 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index a2ce8a9a71a6..b9dc3831dd6b 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -29,6 +29,7 @@
 #include <linux/kexec.h>
 #include <linux/crash_dump.h>
 #include <linux/hugetlb.h>
+#include <linux/acpi_iort.h>
 
 #include <asm/boot.h>
 #include <asm/fixmap.h>
@@ -190,7 +191,7 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max)
 
 #ifdef CONFIG_ZONE_DMA
 	dt_zone_dma_bits = fls64(of_dma_get_max_cpu_address(NULL));
-	zone_dma_bits = min(32U, dt_zone_dma_bits);
+	zone_dma_bits = min3(32U, dt_zone_dma_bits, acpi_iort_get_zone_dma_size());
 	arm64_dma_phys_limit = max_zone_phys(zone_dma_bits);
 	max_zone_pfns[ZONE_DMA] = PFN_DOWN(arm64_dma_phys_limit);
 #endif
diff --git a/drivers/acpi/arm64/iort.c b/drivers/acpi/arm64/iort.c
index 9929ff50c0c0..05fe4a076bab 100644
--- a/drivers/acpi/arm64/iort.c
+++ b/drivers/acpi/arm64/iort.c
@@ -1718,3 +1718,55 @@ void __init acpi_iort_init(void)
 
 	iort_init_platform_devices();
 }
+
+#ifdef CONFIG_ZONE_DMA
+/*
+ * Check the IORT whether any devices exist whose DMA mask is < 32 bits.
+ * If so, return the smallest value encountered, or 32 otherwise.
+ */
+unsigned int __init acpi_iort_get_zone_dma_size(void)
+{
+	struct acpi_table_iort *iort;
+	struct acpi_iort_node *node, *end;
+	acpi_status status;
+	u8 limit = 32;
+	int i;
+
+	if (acpi_disabled)
+		return limit;
+
+	status = acpi_get_table(ACPI_SIG_IORT, 0,
+				(struct acpi_table_header **)&iort);
+	if (ACPI_FAILURE(status))
+		return limit;
+
+	node = ACPI_ADD_PTR(struct acpi_iort_node, iort, iort->node_offset);
+	end = ACPI_ADD_PTR(struct acpi_iort_node, iort, iort->header.length);
+
+	for (i = 0; i < iort->node_count; i++) {
+		if (node >= end)
+			break;
+
+		switch (node->type) {
+			struct acpi_iort_named_component *ncomp;
+			struct acpi_iort_root_complex *rc;
+
+		case ACPI_IORT_NODE_NAMED_COMPONENT:
+			ncomp = (struct acpi_iort_named_component *)node->node_data;
+			limit = min_not_zero(limit, ncomp->memory_address_limit);
+			break;
+
+		case ACPI_IORT_NODE_PCI_ROOT_COMPLEX:
+			if (node->revision < 1)
+				break;
+
+			rc = (struct acpi_iort_root_complex *)node->node_data;
+			limit = min_not_zero(limit, rc->memory_address_limit);
+			break;
+		}
+		node = ACPI_ADD_PTR(struct acpi_iort_node, node, node->length);
+	}
+	acpi_put_table(&iort->header);
+	return limit;
+}
+#endif
diff --git a/include/linux/acpi_iort.h b/include/linux/acpi_iort.h
index 20a32120bb88..7d2e184f0d4d 100644
--- a/include/linux/acpi_iort.h
+++ b/include/linux/acpi_iort.h
@@ -38,6 +38,7 @@ void iort_dma_setup(struct device *dev, u64 *dma_addr, u64 *size);
 const struct iommu_ops *iort_iommu_configure_id(struct device *dev,
 						const u32 *id_in);
 int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head);
+unsigned int acpi_iort_get_zone_dma_size(void);
 #else
 static inline void acpi_iort_init(void) { }
 static inline u32 iort_msi_map_id(struct device *dev, u32 id)
@@ -55,6 +56,9 @@ static inline const struct iommu_ops *iort_iommu_configure_id(
 static inline
 int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head)
 { return 0; }
+
+static inline unsigned int acpi_iort_get_zone_dma_size(void)
+{ return 32; }
 #endif
 
 #endif /* __ACPI_IORT_H__ */
-- 
2.29.0

[PATCH v5 7/7] mm: Remove examples from enum zone_type comment

[Nicolas Saenz Julienne]

We can't really list every setup in common code. On top of that they are
unlikely to stay true for long as things change in the arch trees
independently of this comment.

Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
---
 include/linux/mmzone.h | 20 --------------------
 1 file changed, 20 deletions(-)

diff --git a/include/linux/mmzone.h b/include/linux/mmzone.h
index fb3bf696c05e..9d0c454d23cd 100644
--- a/include/linux/mmzone.h
+++ b/include/linux/mmzone.h
@@ -354,26 +354,6 @@ enum zone_type {
 	 * DMA mask is assumed when ZONE_DMA32 is defined. Some 64-bit
 	 * platforms may need both zones as they support peripherals with
 	 * different DMA addressing limitations.
-	 *
-	 * Some examples:
-	 *
-	 *  - i386 and x86_64 have a fixed 16M ZONE_DMA and ZONE_DMA32 for the
-	 *    rest of the lower 4G.
-	 *
-	 *  - arm only uses ZONE_DMA, the size, up to 4G, may vary depending on
-	 *    the specific device.
-	 *
-	 *  - arm64 has a fixed 1G ZONE_DMA and ZONE_DMA32 for the rest of the
-	 *    lower 4G.
-	 *
-	 *  - powerpc only uses ZONE_DMA, the size, up to 2G, may vary
-	 *    depending on the specific device.
-	 *
-	 *  - s390 uses ZONE_DMA fixed to the lower 2G.
-	 *
-	 *  - ia64 and riscv only use ZONE_DMA32.
-	 *
-	 *  - parisc uses neither.
 	 */
 #ifdef CONFIG_ZONE_DMA
 	ZONE_DMA,
-- 
2.29.0

Re: [PATCH v5 6/7] arm64: mm: Set ZONE_DMA size based on early IORT scan

[Catalin Marinas]

On Thu, Oct 29, 2020 at 06:25:49PM +0100, Nicolas Saenz Julienne wrote:
> diff --git a/drivers/acpi/arm64/iort.c b/drivers/acpi/arm64/iort.c
> index 9929ff50c0c0..05fe4a076bab 100644
> --- a/drivers/acpi/arm64/iort.c
> +++ b/drivers/acpi/arm64/iort.c
> @@ -1718,3 +1718,55 @@ void __init acpi_iort_init(void)
>  
>  	iort_init_platform_devices();
>  }
> +
> +#ifdef CONFIG_ZONE_DMA
> +/*
> + * Check the IORT whether any devices exist whose DMA mask is < 32 bits.
> + * If so, return the smallest value encountered, or 32 otherwise.
> + */
> +unsigned int __init acpi_iort_get_zone_dma_size(void)
> +{
> +	struct acpi_table_iort *iort;
> +	struct acpi_iort_node *node, *end;
> +	acpi_status status;
> +	u8 limit = 32;

Nitpick: can we not return PHYS_ADDR_MAX here, for consistency with
of_dma_get_max_cpu_address()? There wouldn't be any functional change.

-- 
Catalin

Re: [PATCH v5 0/7] arm64: Default to 32-bit wide ZONE_DMA

[Catalin Marinas]

On Thu, Oct 29, 2020 at 06:25:43PM +0100, Nicolas Saenz Julienne wrote:
> Ard Biesheuvel (1):
>   arm64: mm: Set ZONE_DMA size based on early IORT scan
> 
> Nicolas Saenz Julienne (6):
>   arm64: mm: Move reserve_crashkernel() into mem_init()
>   arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
>   of/address: Introduce of_dma_get_max_cpu_address()
>   of: unittest: Add test for of_dma_get_max_cpu_address()
>   arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
>   mm: Remove examples from enum zone_type comment

Thanks for putting this together. I had a minor comment but the patches
look fine to me. We still need an ack from Rob on the DT patch and I can
queue the series for 5.11.

Could you please also test the patch below on top of this series? It's
the removal of the implied DMA offset in the max_zone_phys()
calculation.

--------------------------8<-----------------------------
From 3ae252d888be4984a612236124f5b099e804c745 Mon Sep 17 00:00:00 2001
From: Catalin Marinas <catalin.marinas@arm.com>
Date: Fri, 30 Oct 2020 18:07:34 +0000
Subject: [PATCH] arm64: Ignore any DMA offsets in the max_zone_phys()
 calculation

Currently, the kernel assumes that if RAM starts above 32-bit (or
zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
such constrained devices have a hardwired DMA offset. In practice, we
haven't noticed any such hardware so let's assume that we can expand
ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
zone_bits.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
---
 arch/arm64/mm/init.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index 095540667f0f..362160e16fb2 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -175,14 +175,21 @@ static void __init reserve_elfcorehdr(void)
 #endif /* CONFIG_CRASH_DUMP */
 
 /*
- * Return the maximum physical address for a zone with a given address size
- * limit. It currently assumes that for memory starting above 4G, 32-bit
- * devices will use a DMA offset.
+ * Return the maximum physical address for a zone accessible by the given bits
+ * limit. If the DRAM starts above 32-bit, expand the zone to the maximum
+ * available memory, otherwise cap it at 32-bit.
  */
 static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
 {
-	phys_addr_t offset = memblock_start_of_DRAM() & GENMASK_ULL(63, zone_bits);
-	return min(offset + (1ULL << zone_bits), memblock_end_of_DRAM());
+	phys_addr_t zone_mask = (1ULL << zone_bits) - 1;
+	phys_addr_t phys_start = memblock_start_of_DRAM();
+
+	if (!(phys_start & U32_MAX))
+		zone_mask = PHYS_ADDR_MAX;
+	else if (!(phys_start & zone_mask))
+		zone_mask = U32_MAX;
+
+	return min(zone_mask + 1, memblock_end_of_DRAM());
 }
 
 static void __init zone_sizes_init(unsigned long min, unsigned long max)

Re: [PATCH v5 3/7] of/address: Introduce of_dma_get_max_cpu_address()

[Rob Herring]

On Thu, Oct 29, 2020 at 12:26 PM Nicolas Saenz Julienne
<nsaenzjulienne@suse.de> wrote:
>
> Introduce of_dma_get_max_cpu_address(), which provides the highest CPU
> physical address addressable by all DMA masters in the system. It's
> specially useful for setting memory zones sizes at early boot time.
>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
>
> ---
>
> Changes since v4:
>  - Return max address, not address limit (one-off difference)
>
> Changes since v3:
>  - use u64 with cpu_end
>
> Changes since v2:
>  - Use PHYS_ADDR_MAX
>  - return phys_dma_t
>  - Rename function
>  - Correct subject
>  - Add support to start parsing from an arbitrary device node in order
>    for the function to work with unit tests
>
>  drivers/of/address.c | 42 ++++++++++++++++++++++++++++++++++++++++++
>  include/linux/of.h   |  7 +++++++
>  2 files changed, 49 insertions(+)

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v5 0/7] arm64: Default to 32-bit wide ZONE_DMA

[Nicolas Saenz Julienne]

[-- Attachment #1: Type: text/plain, Size: 3613 bytes --]

On Fri, 2020-10-30 at 18:11 +0000, Catalin Marinas wrote:
> On Thu, Oct 29, 2020 at 06:25:43PM +0100, Nicolas Saenz Julienne wrote:
> > Ard Biesheuvel (1):
> >   arm64: mm: Set ZONE_DMA size based on early IORT scan
> > 
> > Nicolas Saenz Julienne (6):
> >   arm64: mm: Move reserve_crashkernel() into mem_init()
> >   arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
> >   of/address: Introduce of_dma_get_max_cpu_address()
> >   of: unittest: Add test for of_dma_get_max_cpu_address()
> >   arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
> >   mm: Remove examples from enum zone_type comment
> 
> Thanks for putting this together. I had a minor comment but the patches
> look fine to me. We still need an ack from Rob on the DT patch and I can
> queue the series for 5.11.

I'm preparing a v6 unifying both functions as you suggested.

> Could you please also test the patch below on top of this series? It's
> the removal of the implied DMA offset in the max_zone_phys()
> calculation.

Yes, happily. Comments below.

> --------------------------8<-----------------------------
> From 3ae252d888be4984a612236124f5b099e804c745 Mon Sep 17 00:00:00 2001
> From: Catalin Marinas <catalin.marinas@arm.com>
> Date: Fri, 30 Oct 2020 18:07:34 +0000
> Subject: [PATCH] arm64: Ignore any DMA offsets in the max_zone_phys()
>  calculation
> 
> Currently, the kernel assumes that if RAM starts above 32-bit (or
> zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
> such constrained devices have a hardwired DMA offset. In practice, we
> haven't noticed any such hardware so let's assume that we can expand
> ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
> ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
> zone_bits.
> 
> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
> ---
>  arch/arm64/mm/init.c | 17 ++++++++++++-----
>  1 file changed, 12 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
> index 095540667f0f..362160e16fb2 100644
> --- a/arch/arm64/mm/init.c
> +++ b/arch/arm64/mm/init.c
> @@ -175,14 +175,21 @@ static void __init reserve_elfcorehdr(void)
>  #endif /* CONFIG_CRASH_DUMP */
>  
>  /*
> - * Return the maximum physical address for a zone with a given address size
> - * limit. It currently assumes that for memory starting above 4G, 32-bit
> - * devices will use a DMA offset.
> + * Return the maximum physical address for a zone accessible by the given bits
> + * limit. If the DRAM starts above 32-bit, expand the zone to the maximum
> + * available memory, otherwise cap it at 32-bit.
>   */
>  static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
>  {
> -	phys_addr_t offset = memblock_start_of_DRAM() & GENMASK_ULL(63, zone_bits);
> -	return min(offset + (1ULL << zone_bits), memblock_end_of_DRAM());
> +	phys_addr_t zone_mask = (1ULL << zone_bits) - 1;

Maybe use DMA_BIT_MASK(), instead of the manual calculation?

> +	phys_addr_t phys_start = memblock_start_of_DRAM();
> +
> +	if (!(phys_start & U32_MAX))

I'd suggest using 'bigger than' instead of masks. Just to cover ourselves
against memory starting at odd locations. Also it'll behaves properly when
phys_start is zero (this breaks things on RPi4).

> +		zone_mask = PHYS_ADDR_MAX;
> +	else if (!(phys_start & zone_mask))
> +		zone_mask = U32_MAX;
> +
> +	return min(zone_mask + 1, memblock_end_of_DRAM());

This + 1 isn't going to play well when zone_mask is PHYS_ADDR_MAX.

Regards,
Nicolas


[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v5 0/7] arm64: Default to 32-bit wide ZONE_DMA

[Catalin Marinas]

On Tue, Nov 03, 2020 at 06:00:33PM +0100, Nicolas Saenz Julienne wrote:
> On Fri, 2020-10-30 at 18:11 +0000, Catalin Marinas wrote:
> > On Thu, Oct 29, 2020 at 06:25:43PM +0100, Nicolas Saenz Julienne wrote:
> > > Ard Biesheuvel (1):
> > >   arm64: mm: Set ZONE_DMA size based on early IORT scan
> > > 
> > > Nicolas Saenz Julienne (6):
> > >   arm64: mm: Move reserve_crashkernel() into mem_init()
> > >   arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
> > >   of/address: Introduce of_dma_get_max_cpu_address()
> > >   of: unittest: Add test for of_dma_get_max_cpu_address()
> > >   arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
> > >   mm: Remove examples from enum zone_type comment
> > 
> > Thanks for putting this together. I had a minor comment but the patches
> > look fine to me. We still need an ack from Rob on the DT patch and I can
> > queue the series for 5.11.
> 
> I'm preparing a v6 unifying both functions as you suggested.
> 
> > Could you please also test the patch below on top of this series? It's
> > the removal of the implied DMA offset in the max_zone_phys()
> > calculation.
> 
> Yes, happily. Comments below.
> 
> > --------------------------8<-----------------------------
> > From 3ae252d888be4984a612236124f5b099e804c745 Mon Sep 17 00:00:00 2001
> > From: Catalin Marinas <catalin.marinas@arm.com>
> > Date: Fri, 30 Oct 2020 18:07:34 +0000
> > Subject: [PATCH] arm64: Ignore any DMA offsets in the max_zone_phys()
> >  calculation
> > 
> > Currently, the kernel assumes that if RAM starts above 32-bit (or
> > zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
> > such constrained devices have a hardwired DMA offset. In practice, we
> > haven't noticed any such hardware so let's assume that we can expand
> > ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
> > ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
> > zone_bits.
> > 
> > Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
> > ---
> >  arch/arm64/mm/init.c | 17 ++++++++++++-----
> >  1 file changed, 12 insertions(+), 5 deletions(-)
> > 
> > diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
> > index 095540667f0f..362160e16fb2 100644
> > --- a/arch/arm64/mm/init.c
> > +++ b/arch/arm64/mm/init.c
> > @@ -175,14 +175,21 @@ static void __init reserve_elfcorehdr(void)
> >  #endif /* CONFIG_CRASH_DUMP */
> >  
> >  /*
> > - * Return the maximum physical address for a zone with a given address size
> > - * limit. It currently assumes that for memory starting above 4G, 32-bit
> > - * devices will use a DMA offset.
> > + * Return the maximum physical address for a zone accessible by the given bits
> > + * limit. If the DRAM starts above 32-bit, expand the zone to the maximum
> > + * available memory, otherwise cap it at 32-bit.
> >   */
> >  static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
> >  {
> > -	phys_addr_t offset = memblock_start_of_DRAM() & GENMASK_ULL(63, zone_bits);
> > -	return min(offset + (1ULL << zone_bits), memblock_end_of_DRAM());
> > +	phys_addr_t zone_mask = (1ULL << zone_bits) - 1;
> 
> Maybe use DMA_BIT_MASK(), instead of the manual calculation?

Yes.

> 
> > +	phys_addr_t phys_start = memblock_start_of_DRAM();
> > +
> > +	if (!(phys_start & U32_MAX))
> 
> I'd suggest using 'bigger than' instead of masks. Just to cover ourselves
> against memory starting at odd locations. Also it'll behaves properly when
> phys_start is zero (this breaks things on RPi4).

Good point.

> > +		zone_mask = PHYS_ADDR_MAX;
> > +	else if (!(phys_start & zone_mask))
> > +		zone_mask = U32_MAX;
> > +
> > +	return min(zone_mask + 1, memblock_end_of_DRAM());
> 
> This + 1 isn't going to play well when zone_mask is PHYS_ADDR_MAX.

You are right on PHYS_ADDR_MAX overflowing but I'd keep the +1 since
memblock_end_of_DRAM() returns the first byte past the accessible range
(so exclusive end).

I'll tweak this function a bit to avoid the overflow or use the
arm64-specific PHYS_MASK (that's never going to be the full 64 bits).

Thanks.

-- 
Catalin