linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Soeren Sonnenburg <sonnenburg@informatik.hu-berlin.de>
To: Linux Kernel <linux-kernel@vger.kernel.org>
Subject: bug in 2.4.19: USB device not accepting new address=12 (error=-110)
Date: 01 Oct 2002 10:44:22 +0200	[thread overview]
Message-ID: <1033461863.12761.10.camel@sun> (raw)

Hi!

Since the upgrade from 2.4.18 to .19 the following problem with usb
occurs:
First of all my setup is an k7v mainboard to which an usb hub of a ctx
monitor is attached. On that Monitor's usb hub a usb mouse is attached.

When I turn off the monitor and thus disconnect both the usb-mouse and
the monitor and turn the monitor back on *sometimes* the mouse's power
is not toggled back on (in most cases it just works fine).

In the syslog I observe these messages (this is a monitor switch on,
switch off, switch on,... session).

Since the usb driver got updated in 2.4.19 a suspect the bug to be
there.

Sorry if this is already known for quite some time,
Soeren.

Sep 30 20:50:44 zeus kernel: uhci.c: d400: wakeup_hc
Sep 30 20:50:44 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 49b data: 4
Sep 30 20:50:44 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:50:44 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:50:44 zeus kernel: hub.c: port 2 connection change
Sep 30 20:50:44 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:50:44 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:50:44 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:50:44 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 499 data: 4
Sep 30 20:50:44 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:50:45 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:50:45 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:50:45 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 11
Sep 30 20:50:49 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:50:49 zeus kernel: usb.c: USB device not accepting new address=11 (error=-110)
Sep 30 20:50:49 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:50:49 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 12
Sep 30 20:50:53 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:50:53 zeus kernel: usb.c: USB device not accepting new address=12 (error=-110)
Sep 30 20:50:53 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:50:53 zeus kernel: hub.c: port 2, portstatus 101, change 0, 12 Mb/s
Sep 30 20:52:00 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 48a data: 4
Sep 30 20:52:00 zeus kernel: uhci.c: d400: suspend_hc
Sep 30 20:52:00 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:00 zeus kernel: hub.c: port 2, portstatus 100, change 3, 12 Mb/s
Sep 30 20:52:00 zeus kernel: hub.c: port 2 connection change
Sep 30 20:52:00 zeus kernel: hub.c: port 2, portstatus 100, change 3, 12 Mb/s
Sep 30 20:52:00 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 488 data: 4
Sep 30 20:52:00 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:00 zeus kernel: hub.c: port 2, portstatus 100, change 2, 12 Mb/s
Sep 30 20:52:00 zeus kernel: hub.c: port 2 enable change, status 100
Sep 30 20:52:03 zeus kernel: uhci.c: d400: wakeup_hc
Sep 30 20:52:03 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 49b data: 4
Sep 30 20:52:03 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:03 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:52:03 zeus kernel: hub.c: port 2 connection change
Sep 30 20:52:03 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:52:03 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:04 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:04 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 499 data: 4
Sep 30 20:52:04 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:04 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:04 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:52:04 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 13
Sep 30 20:52:08 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:52:08 zeus kernel: usb.c: USB device not accepting new address=13 (error=-110)
Sep 30 20:52:08 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:52:08 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 14
Sep 30 20:52:12 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:52:12 zeus kernel: usb.c: USB device not accepting new address=14 (error=-110)
Sep 30 20:52:12 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:12 zeus kernel: hub.c: port 2, portstatus 101, change 0, 12 Mb/s
Sep 30 20:52:19 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 48a data: 4
Sep 30 20:52:19 zeus kernel: uhci.c: d400: suspend_hc
Sep 30 20:52:19 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:19 zeus kernel: hub.c: port 2, portstatus 100, change 3, 12 Mb/s
Sep 30 20:52:19 zeus kernel: hub.c: port 2 connection change
Sep 30 20:52:19 zeus kernel: hub.c: port 2, portstatus 100, change 3, 12 Mb/s
Sep 30 20:52:19 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 488 data: 4
Sep 30 20:52:19 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:19 zeus kernel: hub.c: port 2, portstatus 100, change 2, 12 Mb/s
Sep 30 20:52:19 zeus kernel: hub.c: port 2 enable change, status 100
Sep 30 20:52:22 zeus kernel: uhci.c: d400: wakeup_hc
Sep 30 20:52:23 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 49b data: 4
Sep 30 20:52:23 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2 connection change
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 3, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:23 zeus kernel: uhci.c: root-hub INT complete: port1: 580 port2: 499 data: 4
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 101, change 2, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:52:23 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 15
Sep 30 20:52:27 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:52:27 zeus kernel: usb.c: USB device not accepting new address=15 (error=-110)
Sep 30 20:52:27 zeus kernel: hub.c: port 2, portstatus 103, change 0, 12 Mb/s
Sep 30 20:52:27 zeus kernel: hub.c: USB new device connect on bus1/2, assigned device number 16
Sep 30 20:52:31 zeus kernel: usb_control/bulk_msg: timeout
Sep 30 20:52:31 zeus kernel: usb.c: USB device not accepting new address=16 (error=-110)
Sep 30 20:52:31 zeus kernel: hub.c: port 1, portstatus 300, change 0, 1.5 Mb/s
Sep 30 20:52:31 zeus kernel: hub.c: port 2, portstatus 101, change 0, 12 Mb/


                 reply	other threads:[~2002-10-01  8:44 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1033461863.12761.10.camel@sun \
    --to=sonnenburg@informatik.hu-berlin.de \
    --cc=linux-kernel@vger.kernel.org \
    --subject='Re: bug in 2.4.19: USB device not accepting new address=12 (error=-110)' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).