From: Adam Johansson <adam.johansson@madsci.se>
To: Jonathan Vardy <jonathan@explainerdc.com>
Cc: linux-kernel@vger.kernel.org
Subject: RE: Promise TX4 100: neither IDE port enabled
Date: 04 Apr 2003 14:39:57 +0200 [thread overview]
Message-ID: <1049459997.1851.4.camel@dgc.madsci.se> (raw)
In-Reply-To: <73300040777B0F44B8CE29C87A0782E101FA9875@exchange.explainerdc.com>
Hi, I can confirm with my experiences with both Ultra and Fasttrak under
recent 2.4.20+ kernels fail detecting more than UDMA33 on these cards.
Without knowing the cause or fix for it I instead run ac-patches.
The card(s) are than configured correctly.
I now run 2.4.21pre5ac3 and I remember 2.4.21pre4ac4 also worked fine.
Cheers!
Adam Johansson
On Fri, 2003-04-04 at 12:56, Jonathan Vardy wrote:
> I've rebooted using the orignal Red Hat kernel (2.4.20) and it
> recongnizes the Promise card. Here are the details:
>
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> PIIX4: IDE controller at PCI slot 00:04.1
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> PDC20270: IDE controller at PCI slot 02:01.0
> PDC20270: chipset revision 2
> PDC20270: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0x9040-0x9047, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0x9048-0x904f, BIOS settings: hdg:pio, hdh:pio
> ide4: BM-DMA at 0x90c0-0x90c7, BIOS settings: hdi:pio, hdj:pio
> ide5: BM-DMA at 0x90c8-0x90cf, BIOS settings: hdk:pio, hdl:pio
> hda: Maxtor 2B020H1, ATA DISK drive
> blk: queue c0453420, I/O limit 4095Mb (mask 0xffffffff)
> hdc: WDC WD1200BB-00CAA1, ATA DISK drive
> blk: queue c04538a0, I/O limit 4095Mb (mask 0xffffffff)
> hde: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0453d20, I/O limit 4095Mb (mask 0xffffffff)
> hdg: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c04541a0, I/O limit 4095Mb (mask 0xffffffff)
> hdi: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0454620, I/O limit 4095Mb (mask 0xffffffff)
> hdk: WDC WD1200BB-60CJA1, ATA DISK drive
> blk: queue c0454aa0, I/O limit 4095Mb (mask 0xffffffff)
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> ide2 at 0x9000-0x9007,0x9012 on irq 19
> ide3 at 0x9020-0x9027,0x9032 on irq 19
> ide4 at 0x9080-0x9087,0x9092 on irq 19
> ide5 at 0x90a0-0x90a7,0x90b2 on irq 19
> hda: host protected area => 1
> hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63,
> UDMA(33)
> hdc: host protected area => 1
> hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(33)
> hde: host protected area => 1
> hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdg: host protected area => 1
> hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdi: host protected area => 1
> hdi: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
> hdk: host protected area => 1
> hdk: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=232581/16/63,
> UDMA(100)
>
>
> Better results but doen anybody know why 2.4.21pre6 can't detect it
> right?
>
> >
> > ide: Assuming 33MHz system bus speed for PIO modes; override
> > with idebus=xx
> > PIIX4: IDE controller at PCI slot 00:04.1
> > PIIX4: chipset revision 1
> > PIIX4: not 100% native mode: will probe irqs later
> > ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
> > ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
> > PDC20270: IDE controller at PCI slot 02:01.0
> > PDC20270: chipset revision 2
> > PDC20270: not 100% native mode: will probe irqs later
> > PDC20270: neither IDE port enabled (BIOS)
> > PDC20270: neither IDE port enabled (BIOS)
> > hda: Maxtor 2B020H1, ATA DISK drive
> > blk: queue c0395860, I/O limit 4095Mb (mask 0xffffffff)
> > hdc: WDC WD1200BB-00CAA1, ATA DISK drive
> > blk: queue c0395cd0, I/O limit 4095Mb (mask 0xffffffff)
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > ide1 at 0x170-0x177,0x376 on irq 15
> > hda: host protected area => 1
> > hda: 39062500 sectors (20000 MB) w/2048KiB Cache,
> > CHS=2431/255/63, UDMA(33)
> > hdc: host protected area => 1
> > hdc: 234441648 sectors (120034 MB) w/2048KiB Cache,
> > CHS=232581/16/63, UDMA(33)
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
next prev parent reply other threads:[~2003-04-04 12:35 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-04-04 10:56 Promise TX4 100: neither IDE port enabled Jonathan Vardy
2003-04-04 12:39 ` Adam Johansson [this message]
2003-04-05 0:03 ` Jonathan Vardy
-- strict thread matches above, loose matches on Subject: below --
2003-04-04 15:07 Jonathan Vardy
2003-04-04 23:58 ` Thomas Backlund
2003-04-05 13:31 ` Adam Johansson
2003-04-04 9:10 Jonathan Vardy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1049459997.1851.4.camel@dgc.madsci.se \
--to=adam.johansson@madsci.se \
--cc=jonathan@explainerdc.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).