From: Felipe Balbi <balbi@ti.com>
To: alan@linux.intel.com
Cc: Tony Lindgren <tony@atomide.com>, Kevin Hilman <khilman@ti.com>,
Linux OMAP Mailing List <linux-omap@vger.kernel.org>,
Linux ARM Kernel Mailing List
<linux-arm-kernel@lists.infradead.org>,
linux-serial@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Santosh Shilimkar <santosh.shilimkar@ti.com>,
Shubhrajyoti Datta <shubhrajyoti@ti.com>,
Felipe Balbi <balbi@ti.com>
Subject: [PATCH v2 06/13] serial: omap: simplify IRQ handling
Date: Tue, 21 Aug 2012 15:16:04 +0300 [thread overview]
Message-ID: <1345551371-18862-7-git-send-email-balbi@ti.com> (raw)
In-Reply-To: <1345551371-18862-1-git-send-email-balbi@ti.com>
quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
---
drivers/tty/serial/omap-serial.c | 48 +++++++++++++++++++++++++++++++---------
1 file changed, 37 insertions(+), 11 deletions(-)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 16808b6..2d3e64e 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -350,33 +350,59 @@ static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
{
struct uart_omap_port *up = dev_id;
unsigned int iir, lsr;
+ unsigned int type;
unsigned long flags;
+ irqreturn_t ret = IRQ_HANDLED;
+ spin_lock_irqsave(&up->port.lock, flags);
pm_runtime_get_sync(up->dev);
iir = serial_in(up, UART_IIR);
+again:
if (iir & UART_IIR_NO_INT) {
- pm_runtime_mark_last_busy(up->dev);
- pm_runtime_put_autosuspend(up->dev);
- return IRQ_NONE;
+ ret = IRQ_NONE;
+ goto out;
}
- spin_lock_irqsave(&up->port.lock, flags);
lsr = serial_in(up, UART_LSR);
- if (iir & UART_IIR_RLSI) {
+
+ /* extract IRQ type from IIR register */
+ type = iir & 0x3e;
+
+ switch (type) {
+ case UART_IIR_MSI:
+ check_modem_status(up);
+ break;
+ case UART_IIR_THRI:
+ if (lsr & UART_LSR_THRE)
+ transmit_chars(up);
+ break;
+ case UART_IIR_RDI:
if (lsr & UART_LSR_DR)
receive_chars(up, &lsr);
+ break;
+ case UART_IIR_RLSI:
+ if (lsr & UART_LSR_BRK_ERROR_BITS)
+ receive_chars(up, &lsr);
+ break;
+ case UART_IIR_RX_TIMEOUT:
+ receive_chars(up, &lsr);
+ break;
+ case UART_IIR_CTS_RTS_DSR:
+ iir = serial_in(up, UART_IIR);
+ goto again;
+ case UART_IIR_XOFF:
+ /* FALLTHROUGH */
+ default:
+ break;
}
- check_modem_status(up);
- if ((lsr & UART_LSR_THRE) && (iir & UART_IIR_THRI))
- transmit_chars(up);
-
+out:
spin_unlock_irqrestore(&up->port.lock, flags);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
-
up->port_activity = jiffies;
- return IRQ_HANDLED;
+
+ return ret;
}
static unsigned int serial_omap_tx_empty(struct uart_port *port)
--
1.7.12.rc3
next prev parent reply other threads:[~2012-08-21 12:20 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-08-21 9:15 [RFC/PATCH 00/13] OMAP UART patches Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 01/13] serial: omap: define and use to_uart_omap_port() Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 02/13] serial: omap: always return IRQ_HANDLED Felipe Balbi
2012-08-21 11:50 ` Alan Cox
2012-08-21 11:54 ` Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 03/13] serial: omap: define helpers for pdata function pointers Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 04/13] serial: omap: don't access the platform_device Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 05/13] serial: omap: drop DMA support Felipe Balbi
2012-08-21 9:44 ` Shilimkar, Santosh
2012-08-21 10:20 ` Felipe Balbi
2012-08-21 10:35 ` Shilimkar, Santosh
2012-08-21 10:34 ` Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 06/13] serial: add OMAP-specific defines Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 07/13] serial: omap: simplify IRQ handling Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 08/13] serial: omap: refactor receive_chars() into rdi/rlsi handlers Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 09/13] serial: omap: move THRE check to transmit_chars() Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 10/13] serial: omap: stick to put_autosuspend Felipe Balbi
2012-08-21 10:42 ` Shilimkar, Santosh
2012-08-21 10:57 ` Felipe Balbi
2012-08-21 11:05 ` Shilimkar, Santosh
2012-08-21 11:02 ` Felipe Balbi
2012-08-21 11:09 ` Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 11/13] serial: omap: set dev->drvdata before enabling pm_runtime Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 12/13] serial: omap: drop unnecessary check from remove Felipe Balbi
2012-08-21 9:15 ` [RFC/PATCH 13/13] serial: omap: make sure to suspend device before remove Felipe Balbi
2012-08-21 10:43 ` [RFC/PATCH 00/13] OMAP UART patches Shilimkar, Santosh
2012-08-21 12:15 ` [PATCH v2 00/13] OMAP Serial patches Felipe Balbi
2012-08-21 12:15 ` [PATCH v2 01/13] serial: omap: define and use to_uart_omap_port() Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 02/13] serial: omap: define helpers for pdata function pointers Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 03/13] serial: omap: don't access the platform_device Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 04/13] serial: omap: drop DMA support Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 05/13] serial: add OMAP-specific defines Felipe Balbi
2012-08-21 12:16 ` Felipe Balbi [this message]
2012-08-21 12:16 ` [PATCH v2 07/13] serial: omap: refactor receive_chars() into rdi/rlsi handlers Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 08/13] serial: omap: move THRE check to transmit_chars() Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 09/13] serial: omap: stick to put_autosuspend Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 10/13] serial: omap: set dev->drvdata before enabling pm_runtime Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 11/13] serial: omap: drop unnecessary check from remove Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 12/13] serial: omap: make sure to suspend device before remove Felipe Balbi
2012-08-21 12:16 ` [PATCH v2 13/13] serial: omap: don't save IRQ flags on hardirq Felipe Balbi
2012-08-21 13:01 ` [PATCH v2 00/13] OMAP Serial patches Felipe Balbi
2012-08-21 15:07 ` Felipe Balbi
2012-08-23 6:26 ` Felipe Balbi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1345551371-18862-7-git-send-email-balbi@ti.com \
--to=balbi@ti.com \
--cc=alan@linux.intel.com \
--cc=khilman@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=santosh.shilimkar@ti.com \
--cc=shubhrajyoti@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).