linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Daniel Lezcano <daniel.lezcano@linaro.org>
To: Lukasz Luba <lukasz.luba@arm.com>, Rob Herring <robh@kernel.org>
Cc: Finley Xiao <finley.xiao@rock-chips.com>,
	heiko@sntech.de, rui.zhang@intel.com,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
	linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
	huangtao@rock-chips.com, tony.xie@rock-chips.com,
	cl@rock-chips.com
Subject: Re: [PATCH v1] thermal/of: Introduce k-po, k-pu and k-i for a thermal zone
Date: Tue, 25 Aug 2020 11:44:31 +0200	[thread overview]
Message-ID: <13b84e7e-adfe-5939-e78d-0a20fce0a92e@linaro.org> (raw)
In-Reply-To: <c3f54e18-8683-8bd9-90fa-e3465cddf8e8@arm.com>

On 25/08/2020 10:25, Lukasz Luba wrote:
> Hi Rob,
> 
> On 8/25/20 12:09 AM, Rob Herring wrote:
>> On Tue, Aug 11, 2020 at 08:31:15PM +0800, Finley Xiao wrote:
>>> The default value for k_pu is:
>>>      2 * sustainable_power / (desired_temperature - switch_on_temp)
>>> The default value for k_po is:
>>>      sustainable_power / (desired_temperature - switch_on_temp)
>>> The default value for k_i is 10.
>>>
>>> Even though these parameters of the PID controller can be changed
>>> by the following sysfs files:
>>>      /sys/class/thermal/thermal_zoneX/k_pu
>>>      /sys/class/thermal/thermal_zoneX/k_po
>>>      /sys/class/thermal/thermal_zoneX/k_i
>>>
>>> But it's still more convenient to change the default values by
>>> devicetree,
>>> so introduce these three optional properties. If provided these
>>> properties,
>>> they will be parsed and associated with the thermal zone via the thermal
>>> zone parameters.
>>>
>>> Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
>>> ---
>>>   Documentation/devicetree/bindings/thermal/thermal.txt | 14
>>> ++++++++++++++
>>
>> Bindings should be a separate file and this one is a DT schema now.
>>
>>>   drivers/thermal/thermal_of.c                          |  7 +++++++
>>>   2 files changed, 21 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt
>>> b/Documentation/devicetree/bindings/thermal/thermal.txt
>>> index f78bec19ca35..ebe936b57ded 100644
>>> --- a/Documentation/devicetree/bindings/thermal/thermal.txt
>>> +++ b/Documentation/devicetree/bindings/thermal/thermal.txt
>>> @@ -165,6 +165,20 @@ Optional property:
>>>               2000mW, while on a 10'' tablet is around
>>>               4500mW.
>>>   +- k-po:            Proportional parameter of the PID controller when
>>> +            current temperature is above the target.
>>> +  Type: signed
>>> +  Size: one cell
>>> +
>>> +- k-pu:            Proportional parameter of the PID controller when
>>> +            current temperature is below the target.
>>> +  Type: signed
>>> +  Size: one cell
>>> +
>>> +- k-i:            Integral parameter of the PID controller.
>>> +  Type: signed
>>> +  Size: one cell
>>
>> What's PID?
>>
>> I know nothing about the sysfs params, but the binding needs to stand on
>> it's own and needs enough detail to educate me.
> Sorry for the delay, I missed that patch.
> These parameters are the coefficients for the
> Proportional-Integral-Derivative (PID) controller [1], which is the
> core of the Intelligent Power Allocation (IPA) thermal governor.

Just a few words to elaborate a bit for Rob who may not have time to
digest the whole concept from Wikipedia :)

The PID is an regulation loop where the input is compared to the output.

For example when driving a car and you aim a speed cruise of 90km/h. You
press the accelerator and watch the current speed. The smaller the
current speed is, the stronger you will push the accelerator. And the
closer to the cruise speed the car is, the lesser you push the
accelerator until the car stabilize to the cruise to speed.

The k-* describes how strong you push the accelerator and release it.

In the thermal framework, that has an impact on how brutal the
mitigation acts and depending on them it results in a flat temperature
curve or a sawtooth aspect.

These coefficient depends on the ambient temperature (casing, room
temperature), the heat sink and the load. Depending on the use cases,
you may want to change their values at runtime.

From my POV, setting these values in the DT does not really make sense.

It would make much more sense to have the thermal specifications of the
board (heat sink capacity, resistivity, max temperature or TDP), so from
there we should be able to compute anything related to the thermal
profile and configure from the kernel.


> Only IPA uses them, thus I don't think the governors parameters:
> k-po, k-pu, k-i
> should be part of the DeviceTree. I haven't seen such governors
> tunnables in the DT, please point me if they exist somewhere.
> 
> Do you think Rob they might be specified in the DT?
> 
> Regards,
> Lukasz
> 
> [1] https://en.wikipedia.org/wiki/PID_controller


-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

  reply	other threads:[~2020-08-25  9:44 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-08-11 12:31 [PATCH v1] thermal/of: Introduce k-po, k-pu and k-i for a thermal zone Finley Xiao
2020-08-24 23:09 ` Rob Herring
2020-08-25  8:25   ` Lukasz Luba
2020-08-25  9:44     ` Daniel Lezcano [this message]
2020-08-25 15:50       ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=13b84e7e-adfe-5939-e78d-0a20fce0a92e@linaro.org \
    --to=daniel.lezcano@linaro.org \
    --cc=cl@rock-chips.com \
    --cc=devicetree@vger.kernel.org \
    --cc=finley.xiao@rock-chips.com \
    --cc=heiko@sntech.de \
    --cc=huangtao@rock-chips.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=lukasz.luba@arm.com \
    --cc=robh@kernel.org \
    --cc=rui.zhang@intel.com \
    --cc=tony.xie@rock-chips.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).