From: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
To: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Zhang Rui <rui.zhang@intel.com>,
Amit Daniel Kachhap <amit.daniel@samsung.com>,
Tomasz Figa <t.figa@samsung.com>,
"Rafael J. Wysocki" <rjw@rjwysocki.net>,
Kyungmin Park <kyungmin.park@samsung.com>,
linux-samsung-soc@vger.kernel.org, linux-pm@vger.kernel.org,
linux-kernel@vger.kernel.org, b.zolnierkie@samsung.com
Subject: [PATCH v3 6/8] thermal: exynos: cache non_hw_trigger_levels in pdata
Date: Thu, 31 Jul 2014 19:11:04 +0200 [thread overview]
Message-ID: <1406826667-2289-7-git-send-email-b.zolnierkie@samsung.com> (raw)
In-Reply-To: <1406826667-2289-1-git-send-email-b.zolnierkie@samsung.com>
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
---
drivers/thermal/samsung/exynos_tmu.c | 16 +++-------------
drivers/thermal/samsung/exynos_tmu.h | 2 ++
drivers/thermal/samsung/exynos_tmu_data.c | 6 ++++++
3 files changed, 11 insertions(+), 13 deletions(-)
diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
index aa4d4fd..6bc8a20 100644
--- a/drivers/thermal/samsung/exynos_tmu.c
+++ b/drivers/thermal/samsung/exynos_tmu.c
@@ -129,7 +129,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
const struct exynos_tmu_registers *reg = pdata->registers;
unsigned int status, trim_info = 0, con;
unsigned int rising_threshold = 0, falling_threshold = 0;
- int ret = 0, threshold_code, i, trigger_levs = 0;
+ int ret = 0, threshold_code, i;
mutex_lock(&data->lock);
clk_enable(data->clk);
@@ -187,15 +187,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
(pdata->efuse_value >> reg->triminfo_85_shift) &
EXYNOS_TMU_TEMP_MASK;
- for (i = 0; i < pdata->max_trigger_level; i++) {
- if (!pdata->trigger_levels[i])
- continue;
-
- /* Count trigger levels except the HW trip*/
- if (!(pdata->trigger_type[i] == HW_TRIP))
- trigger_levs++;
- }
-
rising_threshold = readl(data->base + reg->threshold_th0);
if (data->soc == SOC_ARCH_EXYNOS4210) {
@@ -203,15 +194,14 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
threshold_code = temp_to_code(data, pdata->threshold);
writeb(threshold_code,
data->base + reg->threshold_temp);
- for (i = 0; i < trigger_levs; i++)
+ for (i = 0; i < pdata->non_hw_trigger_levels; i++)
writeb(pdata->trigger_levels[i], data->base +
reg->threshold_th0 + i * sizeof(reg->threshold_th0));
writel(reg->intclr_rise_mask, data->base + reg->tmu_intclear);
} else {
/* Write temperature code for rising and falling threshold */
- for (i = 0;
- i < trigger_levs && i < EXYNOS_MAX_TRIGGER_PER_REG; i++) {
+ for (i = 0; i < pdata->non_hw_trigger_levels; i++) {
threshold_code = temp_to_code(data,
pdata->trigger_levels[i]);
rising_threshold &= ~(0xff << 8 * i);
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 789a8f7..5514d68 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -199,6 +199,7 @@ struct exynos_tmu_registers {
* 1 = enable trigger_level[] interrupt,
* 0 = disable trigger_level[] interrupt
* @max_trigger_level: max trigger level supported by the TMU
+ * @non_hw_trigger_levels: number of defined non-hardware trigger levels
* @gain: gain of amplifier in the positive-TC generator block
* 0 <= gain <= 15
* @reference_voltage: reference voltage of amplifier
@@ -232,6 +233,7 @@ struct exynos_tmu_platform_data {
enum trigger_type trigger_type[MAX_TRIP_COUNT];
bool trigger_enable[MAX_TRIP_COUNT];
u8 max_trigger_level;
+ u8 non_hw_trigger_levels;
u8 gain;
u8 reference_voltage;
u8 noise_cancel_mode;
diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
index 1d05bf8..9c81515 100644
--- a/drivers/thermal/samsung/exynos_tmu_data.c
+++ b/drivers/thermal/samsung/exynos_tmu_data.c
@@ -64,6 +64,7 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
.trigger_type[1] = THROTTLE_ACTIVE,
.trigger_type[2] = SW_TRIP,
.max_trigger_level = 4,
+ .non_hw_trigger_levels = 3,
.gain = 15,
.reference_voltage = 7,
.cal_type = TYPE_ONE_POINT_TRIMMING,
@@ -140,6 +141,7 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = {
.trigger_type[2] = SW_TRIP, \
.trigger_type[3] = HW_TRIP, \
.max_trigger_level = 4, \
+ .non_hw_trigger_levels = 3, \
.gain = 8, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
@@ -230,6 +232,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = {
.trigger_type[2] = SW_TRIP, \
.trigger_type[3] = HW_TRIP, \
.max_trigger_level = 4, \
+ .non_hw_trigger_levels = 3, \
.gain = 8, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
@@ -331,6 +334,7 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = {
.trigger_type[2] = SW_TRIP, \
.trigger_type[3] = HW_TRIP, \
.max_trigger_level = 4, \
+ .non_hw_trigger_levels = 3, \
.gain = 8, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
@@ -422,6 +426,7 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = {
.trigger_type[2] = SW_TRIP, \
.trigger_type[3] = HW_TRIP, \
.max_trigger_level = 4, \
+ .non_hw_trigger_levels = 3, \
.gain = 8, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
@@ -514,6 +519,7 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = {
.trigger_type[0] = SW_TRIP, \
.trigger_type[4] = HW_TRIP, \
.max_trigger_level = 5, \
+ .non_hw_trigger_levels = 1, \
.gain = 5, \
.reference_voltage = 16, \
.noise_cancel_mode = 4, \
--
1.8.2.3
next prev parent reply other threads:[~2014-07-31 17:12 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-07-31 17:10 [PATCH v3 0/8] thermal: exynos: various cleanups Bartlomiej Zolnierkiewicz
2014-07-31 17:10 ` [PATCH v3 1/8] thermal: exynos: remove unused struct exynos_tmu_registers entries Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` [PATCH v3 2/8] thermal: exynos: remove dead code for HW_MODE calibration Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` [PATCH v3 3/8] thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize() Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` [PATCH v3 4/8] thermal: exynos: remove redundant threshold_code " Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` [PATCH v3 5/8] thermal: exynos: simplify temp_to_code() and code_to_temp() Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` Bartlomiej Zolnierkiewicz [this message]
2014-07-31 17:11 ` [PATCH v3 7/8] thermal: exynos: remove redundant pdata checks from exynos_tmu_control() Bartlomiej Zolnierkiewicz
2014-07-31 17:11 ` [PATCH v3 8/8] thermal: exynos: remove identical values from exynos*_tmu_registers structures Bartlomiej Zolnierkiewicz
2014-08-28 14:49 ` [PATCH v3 0/8] thermal: exynos: various cleanups Eduardo Valentin
2014-09-01 10:53 ` amit daniel kachhap
2014-09-01 11:05 ` edubezval
2014-08-29 19:25 ` Eduardo Valentin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1406826667-2289-7-git-send-email-b.zolnierkie@samsung.com \
--to=b.zolnierkie@samsung.com \
--cc=amit.daniel@samsung.com \
--cc=eduardo.valentin@ti.com \
--cc=kyungmin.park@samsung.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=rjw@rjwysocki.net \
--cc=rui.zhang@intel.com \
--cc=t.figa@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).