From: Boris Brezillon <boris.brezillon@free-electrons.com>
To: Nicolas Ferre <nicolas.ferre@atmel.com>,
Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>,
Alexandre Belloni <alexandre.belloni@free-electrons.com>,
Andrew Victor <linux@maxim.org.za>,
Peter Korsgaard <jacmet@sunsite.dk>,
Matt Mackall <mpm@selenic.com>,
Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-arm-kernel@lists.infradead.org,
Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Boris Brezillon <boris.brezillon@free-electrons.com>
Subject: [PATCH 6/6] ARM: at91/dt: add ISI node
Date: Tue, 30 Sep 2014 18:19:47 +0200 [thread overview]
Message-ID: <1412093987-30241-7-git-send-email-boris.brezillon@free-electrons.com> (raw)
In-Reply-To: <1412093987-30241-1-git-send-email-boris.brezillon@free-electrons.com>
Add ISI (Image Sensor Interface) DT node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
---
arch/arm/boot/dts/at91sam9g45.dtsi | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 790c890..5d8746a 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -804,6 +804,27 @@
};
};
+ isi {
+ pinctrl_isi: isi-0 {
+ atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* D8 */
+ AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* D9 */
+ AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* D10 */
+ AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE /* D11 */
+ AT91_PIOB 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* D0 */
+ AT91_PIOB 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* D1 */
+ AT91_PIOB 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* D2 */
+ AT91_PIOB 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* D3 */
+ AT91_PIOB 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* D4 */
+ AT91_PIOB 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* D5 */
+ AT91_PIOB 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* D6 */
+ AT91_PIOB 27 AT91_PERIPH_A AT91_PINCTRL_NONE /* D7 */
+ AT91_PIOB 28 AT91_PERIPH_A AT91_PINCTRL_NONE /* PCK */
+ AT91_PIOB 29 AT91_PERIPH_A AT91_PINCTRL_NONE /* VSYNC */
+ AT91_PIOB 30 AT91_PERIPH_A AT91_PINCTRL_NONE /* HSYNC */
+ AT91_PIOB 31 AT91_PERIPH_A AT91_PINCTRL_NONE /* MCK */>;
+ };
+ };
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -1029,6 +1050,17 @@
};
};
+ isi@fffb4000 {
+ compatible = "atmel,at91sam9g45-isi";
+ reg = <0xfffb4000 0x4000>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 5>;
+ clocks = <&isi_clk>;
+ clock-names = "isi_clk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi>;
+ status = "disabled";
+ };
+
pwm0: pwm@fffb8000 {
compatible = "atmel,at91sam9rl-pwm";
reg = <0xfffb8000 0x300>;
--
1.9.1
next prev parent reply other threads:[~2014-09-30 16:20 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-30 16:19 [PATCH 0/6] ARM: at91: remove at91sam9g45/9m10 legacy board support Boris Brezillon
2014-09-30 16:19 ` [PATCH 1/6] " Boris Brezillon
2014-09-30 16:56 ` Nicolas Ferre
2014-10-01 15:59 ` Alexandre Belloni
2014-09-30 16:19 ` [PATCH 2/6] hwrng: atmel: use clk_prepapre_enable/_disable_unprepare Boris Brezillon
2014-09-30 16:55 ` Peter Korsgaard
2014-10-01 7:13 ` [PATCH v2 " Boris Brezillon
2014-09-30 16:19 ` [PATCH 3/6] hwrng: atmel: add DT support Boris Brezillon
2014-09-30 16:57 ` Peter Korsgaard
2014-09-30 16:19 ` [PATCH 4/6] hwrng: atmel: Add TRNG DT binding doc Boris Brezillon
2014-09-30 17:12 ` Peter Korsgaard
2014-09-30 17:21 ` Boris Brezillon
2014-09-30 17:35 ` Peter Korsgaard
2014-09-30 16:19 ` [PATCH 5/6] ARM: at91/dt: add trng node Boris Brezillon
2014-11-19 15:57 ` Nicolas Ferre
2014-09-30 16:19 ` Boris Brezillon [this message]
2014-11-19 15:51 ` [PATCH 6/6] ARM: at91/dt: add ISI node Nicolas Ferre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1412093987-30241-7-git-send-email-boris.brezillon@free-electrons.com \
--to=boris.brezillon@free-electrons.com \
--cc=alexandre.belloni@free-electrons.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=herbert@gondor.apana.org.au \
--cc=ijc+devicetree@hellion.org.uk \
--cc=jacmet@sunsite.dk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@maxim.org.za \
--cc=mark.rutland@arm.com \
--cc=mpm@selenic.com \
--cc=nicolas.ferre@atmel.com \
--cc=pawel.moll@arm.com \
--cc=plagnioj@jcrosoft.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).