From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S934481AbbCQJtL (ORCPT ); Tue, 17 Mar 2015 05:49:11 -0400 Received: from mail-pa0-f42.google.com ([209.85.220.42]:35305 "EHLO mail-pa0-f42.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932486AbbCQJs4 (ORCPT ); Tue, 17 Mar 2015 05:48:56 -0400 From: Peter Hung X-Google-Original-From: Peter Hung To: johan@kernel.org Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org, tom_tsai@fintek.com.tw, peter_hong@fintek.com.tw, Peter Hung Subject: [PATCH V9 07/10] USB: f81232: implement set_termios() Date: Tue, 17 Mar 2015 17:48:25 +0800 Message-Id: <1426585708-6382-8-git-send-email-hpeter+linux_kernel@gmail.com> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1426585708-6382-1-git-send-email-hpeter+linux_kernel@gmail.com> References: <1426585708-6382-1-git-send-email-hpeter+linux_kernel@gmail.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The original driver had do not any h/w change in driver. This patch implements with configure H/W for baud/parity/word length/stop bits functional in f81232_set_termios(). This patch also implement DTR/RTS control when baudrate B0. We drop DTR/RTS when B0, otherwise enable it. We are checking baudrate in set_termios() too, If baudrate larger then 115200, it will be changed to 115200 and use tty_encode_baud_rate() to encode into tty Signed-off-by: Peter Hung --- drivers/usb/serial/f81232.c | 112 ++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 108 insertions(+), 4 deletions(-) diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c index f0109a4..6be37f3 100644 --- a/drivers/usb/serial/f81232.c +++ b/drivers/usb/serial/f81232.c @@ -31,14 +31,19 @@ static const struct usb_device_id id_table[] = { }; MODULE_DEVICE_TABLE(usb, id_table); +/* Maximum baudrate for F81232 */ +#define F81232_MAX_BAUDRATE 115200 + /* USB Control EP parameter */ #define F81232_REGISTER_REQUEST 0xa0 #define F81232_GET_REGISTER 0xc0 #define F81232_SET_REGISTER 0x40 #define SERIAL_BASE_ADDRESS 0x0120 +#define RECEIVE_BUFFER_REGISTER (0x00 + SERIAL_BASE_ADDRESS) #define INTERRUPT_ENABLE_REGISTER (0x01 + SERIAL_BASE_ADDRESS) #define FIFO_CONTROL_REGISTER (0x02 + SERIAL_BASE_ADDRESS) +#define LINE_CONTROL_REGISTER (0x03 + SERIAL_BASE_ADDRESS) #define MODEM_CONTROL_REGISTER (0x04 + SERIAL_BASE_ADDRESS) #define MODEM_STATUS_REGISTER (0x06 + SERIAL_BASE_ADDRESS) @@ -64,6 +69,11 @@ struct f81232_private { struct usb_serial_port *port; }; +static int calc_baud_divisor(speed_t baudrate) +{ + return DIV_ROUND_CLOSEST(F81232_MAX_BAUDRATE, baudrate); +} + static int f81232_get_register(struct usb_serial_port *port, u16 reg, u8 *val) { int status; @@ -350,6 +360,53 @@ static void f81232_break_ctl(struct tty_struct *tty, int break_state) */ } +static void f81232_set_baudrate(struct usb_serial_port *port, speed_t baudrate) +{ + u8 lcr; + int divisor, status = 0; + + divisor = calc_baud_divisor(baudrate); + + status = f81232_get_register(port, LINE_CONTROL_REGISTER, + &lcr); /* get LCR */ + if (status) { + dev_err(&port->dev, "%s failed to get LCR: %d\n", + __func__, status); + return; + } + + status = f81232_set_register(port, LINE_CONTROL_REGISTER, + lcr | UART_LCR_DLAB); /* Enable DLAB */ + if (status) { + dev_err(&port->dev, "%s failed to set DLAB: %d\n", + __func__, status); + return; + } + + status = f81232_set_register(port, RECEIVE_BUFFER_REGISTER, + divisor & 0x00ff); /* low */ + if (status) { + dev_err(&port->dev, "%s failed to set baudrate MSB: %d\n", + __func__, status); + goto reapply_lcr; + } + + status = f81232_set_register(port, INTERRUPT_ENABLE_REGISTER, + (divisor & 0xff00) >> 8); /* high */ + if (status) { + dev_err(&port->dev, "%s failed to set baudrate LSB: %d\n", + __func__, status); + } + +reapply_lcr: + status = f81232_set_register(port, LINE_CONTROL_REGISTER, + lcr & ~UART_LCR_DLAB); + if (status) { + dev_err(&port->dev, "%s failed to set DLAB: %d\n", + __func__, status); + } +} + static int f81232_port_enable(struct usb_serial_port *port) { u8 val; @@ -395,15 +452,62 @@ static int f81232_port_disable(struct usb_serial_port *port) static void f81232_set_termios(struct tty_struct *tty, struct usb_serial_port *port, struct ktermios *old_termios) { - /* FIXME - Stubbed out for now */ + u8 new_lcr = 0; + int status = 0; + speed_t baudrate; /* Don't change anything if nothing has changed */ if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios)) return; - /* Do the real work here... */ - if (old_termios) - tty_termios_copy_hw(&tty->termios, old_termios); + if (C_BAUD(tty) == B0) + f81232_set_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS); + else if (old_termios && (old_termios->c_cflag & CBAUD) == B0) + f81232_set_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0); + + baudrate = tty_get_baud_rate(tty); + if (baudrate > 0) { + if (baudrate > F81232_MAX_BAUDRATE) { + baudrate = F81232_MAX_BAUDRATE; + tty_encode_baud_rate(tty, baudrate, baudrate); + } + f81232_set_baudrate(port, baudrate); + } + + if (C_PARENB(tty)) { + new_lcr |= UART_LCR_PARITY; + + if (!C_PARODD(tty)) + new_lcr |= UART_LCR_EPAR; + + if (C_CMSPAR(tty)) + new_lcr |= UART_LCR_SPAR; + } + + if (C_CSTOPB(tty)) + new_lcr |= UART_LCR_STOP; + + switch (C_CSIZE(tty)) { + case CS5: + new_lcr |= UART_LCR_WLEN5; + break; + case CS6: + new_lcr |= UART_LCR_WLEN6; + break; + case CS7: + new_lcr |= UART_LCR_WLEN7; + break; + default: + case CS8: + new_lcr |= UART_LCR_WLEN8; + break; + } + + status = f81232_set_register(port, LINE_CONTROL_REGISTER, new_lcr); + if (status) { + dev_err(&port->dev, "%s failed to set LCR: %d\n", + __func__, status); + } } static int f81232_tiocmget(struct tty_struct *tty) -- 1.9.1