From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1757826AbbLBK1j (ORCPT ); Wed, 2 Dec 2015 05:27:39 -0500 Received: from mail-wm0-f41.google.com ([74.125.82.41]:35436 "EHLO mail-wm0-f41.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755339AbbLBKZj (ORCPT ); Wed, 2 Dec 2015 05:25:39 -0500 From: Bartosz Golaszewski To: Wolfram Sang Cc: linux-i2c , LKML , Bartosz Golaszewski Subject: [RESEND PATCH v2 4/9] eeprom: at24: support reading of the serial number Date: Wed, 2 Dec 2015 11:25:21 +0100 Message-Id: <1449051926-21918-5-git-send-email-bgolaszewski@baylibre.com> X-Mailer: git-send-email 2.1.4 In-Reply-To: <1449051926-21918-1-git-send-email-bgolaszewski@baylibre.com> References: <1449051926-21918-1-git-send-email-bgolaszewski@baylibre.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The at24cs series EEPROM chips have an additional read-only memory area containing a factory pre-programmed serial number. In order to access it, one has to perform a dummy write before reading the serial number bytes. Add a function that allows to access the serial number. Signed-off-by: Bartosz Golaszewski --- drivers/misc/eeprom/at24.c | 71 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 71 insertions(+) diff --git a/drivers/misc/eeprom/at24.c b/drivers/misc/eeprom/at24.c index 08cc327..6182f47 100644 --- a/drivers/misc/eeprom/at24.c +++ b/drivers/misc/eeprom/at24.c @@ -163,6 +163,77 @@ static struct i2c_client *at24_translate_offset(struct at24_data *at24, return at24->client[i]; } +static int __attribute__((unused)) at24cs_eeprom_serial_read( + struct at24_data *at24, + char *buf, unsigned offset, + size_t count) +{ + unsigned long timeout, read_time; + struct i2c_client *client; + struct i2c_msg msg[2]; + u8 addrbuf[2]; + int status; + + mutex_lock(&at24->lock); + + client = at24->client[1]; + + memset(msg, 0, sizeof(msg)); + msg[0].addr = client->addr; + msg[0].buf = addrbuf; + + /* + * The address pointer of the device is shared between the regular + * EEPROM array and the serial number block. The dummy write (part of + * the sequential read protocol) ensures the address pointer is reset + * to the desired position. + */ + if (at24->chip.flags & AT24_FLAG_ADDR16) { + /* + * For 16 bit address pointers, the word address must contain + * a '10' sequence in bits 11 and 10 regardless of the + * intended position of the address pointer. + */ + addrbuf[0] = 0x08; + addrbuf[1] = offset; + msg[0].len = 2; + } else { + /* + * Otherwise the word address must begin with a '10' sequence, + * regardless of the intended address. + */ + addrbuf[0] = 0x80 + offset; + msg[0].len = 1; + } + + msg[1].addr = client->addr; + msg[1].flags = I2C_M_RD; + msg[1].buf = buf; + msg[1].len = count; + + /* + * Reads fail if the previous write didn't complete yet. We may + * loop a few times until this one succeeds, waiting at least + * long enough for one entire page write to work. + */ + timeout = jiffies + msecs_to_jiffies(write_timeout); + do { + read_time = jiffies; + status = i2c_transfer(client->adapter, msg, 2); + if (status == 2) { + mutex_unlock(&at24->lock); + return count; + } + + /* REVISIT: at HZ=100, this is sloooow */ + msleep(1); + } while (time_before(read_time, timeout)); + + mutex_unlock(&at24->lock); + + return -ETIMEDOUT; +} + static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf, unsigned offset, size_t count) { -- 2.1.4