From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751218AbcFEJdp (ORCPT ); Sun, 5 Jun 2016 05:33:45 -0400 Received: from mailgw01.mediatek.com ([218.249.47.110]:44843 "EHLO mailgw01.mediatek.com" rhost-flags-OK-FAIL-OK-FAIL) by vger.kernel.org with ESMTP id S1750785AbcFEJdn (ORCPT ); Sun, 5 Jun 2016 05:33:43 -0400 Message-ID: <1465119212.11651.141.camel@mhfsdcap03> Subject: Re: [PATCH v2,3/5] dt-bindings: mtu3: add devicetree bindings From: chunfeng yun To: Matthias Brugger CC: Greg Kroah-Hartman , Felipe Balbi , Mathias Nyman , Alan Stern , Rob Herring , Mark Rutland , Ian Campbell , Sergei Shtylyov , Pawel Moll , Kumar Gala , Sascha Hauer , , , , , Date: Sun, 5 Jun 2016 17:33:32 +0800 In-Reply-To: <5751874C.9070100@gmail.com> References: <1464673962-11506-1-git-send-email-chunfeng.yun@mediatek.com> <1464673962-11506-4-git-send-email-chunfeng.yun@mediatek.com> <5751874C.9070100@gmail.com> Content-Type: text/plain; charset="UTF-8" X-Mailer: Evolution 3.2.3-0ubuntu6 Content-Transfer-Encoding: 7bit MIME-Version: 1.0 X-MTK: N Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org On Fri, 2016-06-03 at 15:34 +0200, Matthias Brugger wrote: > > On 31/05/16 07:52, Chunfeng Yun wrote: > > add a DT binding doc for MediaTek USB3 DRD driver > > > > Signed-off-by: Chunfeng Yun > > --- > > Documentation/devicetree/bindings/usb/mtu3.txt | 85 ++++++++++++++++++++++++ > > 1 file changed, 85 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/usb/mtu3.txt > > > > diff --git a/Documentation/devicetree/bindings/usb/mtu3.txt b/Documentation/devicetree/bindings/usb/mtu3.txt > > new file mode 100644 > > index 0000000..571ae8b > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/mtu3.txt > > The file should be called mt8173-mtu3.txt to be in line with mt8173-xhci.txt > Ok, I will rename it > > > @@ -0,0 +1,85 @@ > > +The device node for Mediatek USB3.0 DRD controller > > + > > +Required properties: > > + - compatible : should be "mediatek,mt8173-mtu3" > > + - reg : specifies physical base address and size of the registers > > + - reg-names: should be "mac" for device IP and "ippc" for IP port control > > + - interrupts : interrupt used by the device IP > > + - power-domains : a phandle to USB power domain node to control USB's > > + mtcmos > > + - vusb33-supply : regulator of USB avdd3.3v > > + - clocks : a list of phandle + clock-specifier pairs, one for each > > + entry in clock-names > > + - clock-names : must contain "sys_ck" for clock of controller; > > + "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are > > + depends on "mediatek,enable-wakeup" > > + - phys : a list of phandle + phy specifier pairs > > + - dr_mode : should be one of "host", "peripheral" or "otg", > > + refer to usb/generic.txt > > + > > +Optional properties: > > + - #address-cells, #size-cells : should be '2' if the device has sub-nodes > > + with 'reg' property > > + - ranges : allows valid 1:1 translation between child's address space and > > + parent's address space > > + - extcon : external connector for vbus and idpin changes detection, needed > > + when supports dual-role mode. > > + - vbus-supply : reference to the VBUS regulator, needed when supports > > + dual-role mode. > > + - pinctl-names : a pinctrl state named "default" must be defined, > > + "id_float" and "id_ground" are optinal which depends on > > + "mediatek,enable-manual-drd" > > So pinctrl is optional, but if you put it, you need at least "default"? Yes, the first one is "default". > > Apart from that, DT maintainers prefer to have the binding patches at > the beginning of a series, so it's easier for them to not oversee any. > Ok. Thanks a lot. > Regards, > Matthias