linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH v3 0/2] Add a new Rockchip usb2 phy driver
@ 2016-06-06  9:20 Frank Wang
  2016-06-06  9:20 ` [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY Frank Wang
  2016-06-06  9:20 ` [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy Frank Wang
  0 siblings, 2 replies; 14+ messages in thread
From: Frank Wang @ 2016-06-06  9:20 UTC (permalink / raw)
  To: heiko, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, mark.rutland, ijc+devicetree, galak
  Cc: linux-kernel, devicetree, linux-usb, linux-rockchip, xzy.xu,
	kever.yang, huangtao, william.wu, frank.wang

The newer SoCs (rk3366, rk3399) of Rock-chip take a different usb-phy
IP block than rk3288 and before, and most of phy-related registers are
also different from the past, so a new phy driver is required necessarily.

These series patches add phy-rockchip-inno-usb2.c and the corresponding
documentation.

Changes in v3:
 - Supplemented some hardware-description into the devicetree bindings.
 - Resolved the mapping defect between fixed value in driver and the property
   in devicetree.
 - Code cleanup.

Changes in v2:
 - Specified more hardware-description into the devicetree bindings.
 - Optimized some process of driver.

Frank Wang (2):
  Documentation: bindings: add DT documentation for Rockchip USB2PHY
  phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy

 .../bindings/phy/phy-rockchip-inno-usb2.txt        |   60 ++
 drivers/phy/Kconfig                                |    7 +
 drivers/phy/Makefile                               |    1 +
 drivers/phy/phy-rockchip-inno-usb2.c               |  630 ++++++++++++++++++++
 4 files changed, 698 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
 create mode 100644 drivers/phy/phy-rockchip-inno-usb2.c

-- 
1.7.9.5

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-06  9:20 [PATCH v3 0/2] Add a new Rockchip usb2 phy driver Frank Wang
@ 2016-06-06  9:20 ` Frank Wang
  2016-06-06 11:27   ` Mark Rutland
  2016-06-06  9:20 ` [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy Frank Wang
  1 sibling, 1 reply; 14+ messages in thread
From: Frank Wang @ 2016-06-06  9:20 UTC (permalink / raw)
  To: heiko, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, mark.rutland, ijc+devicetree, galak
  Cc: linux-kernel, devicetree, linux-usb, linux-rockchip, xzy.xu,
	kever.yang, huangtao, william.wu, frank.wang

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
---

Changes in v3:
 - Added 'clocks' and 'clock-names' optional properties.
 - Specified 'otg-port' and 'host-port' as the sub-node name.

Changes in v2:
 - Changed vbus_host optional property from gpio to regulator.
 - Specified vbus_otg-supply optional property.
 - Specified otg_id and otg_bvalid property.

 .../bindings/phy/phy-rockchip-inno-usb2.txt        |   60 ++++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
new file mode 100644
index 0000000..0b4bbbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
@@ -0,0 +1,60 @@
+ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
+
+Required properties (phy (parent) node):
+ - compatible : should be one of the listed compatibles:
+	* "rockchip,rk3366-usb2phy"
+	* "rockchip,rk3399-usb2phy"
+ - #clock-cells : should be 0.
+ - clock-output-names : specify the 480m output clock name.
+
+Optional properties:
+ - clocks : phandle + phy specifier pair, for the input clock of phy.
+ - clock-names : input clock name of phy, must be "phyclk".
+ - vbus_host-supply : phandle to a regulator that supplies host vbus.
+ - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
+
+Required nodes : a sub-node is required for each port the phy provides.
+		 The sub-node name is used to identify host or otg port,
+		 and shall be the following entries:
+	* "otg-port" : the name of otg port.
+	* "host-port" : the name of host port.
+
+Required properties (port (child) node):
+ - #phy-cells : must be 0. See ./phy-bindings.txt for details.
+ - interrupts : specify an interrupt for each entry in interrupt-names.
+ - interrupt-names : a list which shall be the following entries:
+	* "otg_id" : for the otg id interrupt.
+	* "otg_bvalid" : for the otg vbus interrupt.
+	* "linestate" : for the host/otg linestate interrupt.
+
+Example:
+
+grf: syscon@ff770000 {
+	compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+...
+
+	u2phy: usb2-phy {
+		compatible = "rockchip,rk3366-usb2phy";
+		#clock-cells = <0>;
+		clock-output-names = "sclk_otgphy0_480m";
+
+		u2phy_otg: otg-port {
+			#phy-cells = <0>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "otg_id", "otg_bvalid", "linestate";
+			status = "okay";
+		};
+
+		u2phy_host: host-port {
+			#phy-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "linestate";
+			status = "okay";
+		};
+	};
+};
-- 
1.7.9.5

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy
  2016-06-06  9:20 [PATCH v3 0/2] Add a new Rockchip usb2 phy driver Frank Wang
  2016-06-06  9:20 ` [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY Frank Wang
@ 2016-06-06  9:20 ` Frank Wang
  2016-06-07  9:54   ` Heiko Stübner
  1 sibling, 1 reply; 14+ messages in thread
From: Frank Wang @ 2016-06-06  9:20 UTC (permalink / raw)
  To: heiko, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, mark.rutland, ijc+devicetree, galak
  Cc: linux-kernel, devicetree, linux-usb, linux-rockchip, xzy.xu,
	kever.yang, huangtao, william.wu, frank.wang

The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
than rk3288 and before, and most of phy-related registers are also
different from the past, so a new phy driver is required necessarily.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
---

Changes in v3:
 - Resolved the mapping defect between fixed value in driver and the property
   in devicetree.
 - Optimized 480m output clock register function.
 - Code cleanup.

Changes in v2:
 - Changed vbus_host operation from gpio to regulator in *_probe.
 - Improved the fault treatment relate to 480m clock register.
 - Cleaned up some meaningless codes in *_clk480m_disable.
 - made more clear the comment of *_sm_work.

 drivers/phy/Kconfig                  |    7 +
 drivers/phy/Makefile                 |    1 +
 drivers/phy/phy-rockchip-inno-usb2.c |  630 ++++++++++++++++++++++++++++++++++
 3 files changed, 638 insertions(+)
 create mode 100644 drivers/phy/phy-rockchip-inno-usb2.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index b869b98..29ef15c 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -347,6 +347,13 @@ config PHY_ROCKCHIP_USB
 	help
 	  Enable this to support the Rockchip USB 2.0 PHY.
 
+config PHY_ROCKCHIP_INNO_USB2
+	tristate "Rockchip INNO USB2PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+
 config PHY_ROCKCHIP_EMMC
 	tristate "Rockchip EMMC PHY Driver"
 	depends on ARCH_ROCKCHIP && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 9c3e73c..4963fbc 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -38,6 +38,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
 obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
 obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
 obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
 obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
diff --git a/drivers/phy/phy-rockchip-inno-usb2.c b/drivers/phy/phy-rockchip-inno-usb2.c
new file mode 100644
index 0000000..a2c4f96
--- /dev/null
+++ b/drivers/phy/phy-rockchip-inno-usb2.c
@@ -0,0 +1,630 @@
+/*
+ * Rockchip USB2.0 PHY with Innosilicon IP block driver
+ *
+ * Copyright (C) 2016 Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/gpio/consumer.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+
+#define BIT_WRITEABLE_SHIFT	16
+#define SCHEDULE_DELAY	(60 * HZ)
+
+enum rockchip_usb2phy_port_id {
+	USB2PHY_PORT_OTG,
+	USB2PHY_PORT_HOST,
+	USB2PHY_NUM_PORTS,
+};
+
+enum rockchip_usb2phy_host_state {
+	PHY_STATE_HS_ONLINE	= 0,
+	PHY_STATE_DISCONNECT	= 1,
+	PHY_STATE_HS_CONNECT	= 2,
+	PHY_STATE_FS_CONNECT	= 4,
+};
+
+struct usb2phy_reg {
+	unsigned int	offset;
+	unsigned int	bitend;
+	unsigned int	bitstart;
+	unsigned int	disable;
+	unsigned int	enable;
+};
+
+/**
+ * struct rockchip_usb2phy_port_cfg: usb-phy port configuration.
+ * @phy_sus: phy suspend register.
+ * @ls_det_en: linestate detection enable register.
+ * @ls_det_st: linestate detection state register.
+ * @ls_det_clr: linestate detection clear register.
+ * @utmi_ls: utmi linestate state register.
+ * @utmi_hstdet: utmi host disconnect register.
+ */
+struct rockchip_usb2phy_port_cfg {
+	struct usb2phy_reg	phy_sus;
+	struct usb2phy_reg	ls_det_en;
+	struct usb2phy_reg	ls_det_st;
+	struct usb2phy_reg	ls_det_clr;
+	struct usb2phy_reg	utmi_ls;
+	struct usb2phy_reg	utmi_hstdet;
+};
+
+/**
+ * struct rockchip_usb2phy_cfg: usb-phy configuration.
+ * @num_ports: specify how many ports that the phy has.
+ * @clkout_ctl: keep on/turn off output clk of phy.
+ */
+struct rockchip_usb2phy_cfg {
+	unsigned int	num_ports;
+	struct usb2phy_reg	clkout_ctl;
+	const struct rockchip_usb2phy_port_cfg	port_cfgs[USB2PHY_NUM_PORTS];
+};
+
+/**
+ * struct rockchip_usb2phy_port: usb-phy port data.
+ * @port_id: flag for otg port or host port.
+ * @suspended: phy suspended flag.
+ * @ls_irq: IRQ number assigned for linestate detection.
+ * @mutex: for register updating in sm_work.
+ * @sm_work: OTG state machine work.
+ * @phy_cfg: port register configuration, assigned by driver data.
+ */
+struct rockchip_usb2phy_port {
+	struct phy	*phy;
+	unsigned int	port_id;
+	bool		suspended;
+	int		ls_irq;
+	struct mutex	mutex;
+	struct		delayed_work sm_work;
+	const struct	rockchip_usb2phy_port_cfg *port_cfg;
+};
+
+/**
+ * struct rockchip_usb2phy: usb2.0 phy driver data.
+ * @grf: General Register Files regmap.
+ * @clk: clock struct of phy input clk.
+ * @clk480m: clock struct of phy output clk.
+ * @clk_hw: clock struct of phy output clk management.
+ * @vbus_host: the regulator for vbus_host supply.
+ * @phy_cfg: phy register configuration, assigned by driver data.
+ * @ports: phy port instance.
+ */
+struct rockchip_usb2phy {
+	struct device	*dev;
+	struct regmap	*grf;
+	struct clk	*clk;
+	struct clk	*clk480m;
+	struct clk_hw	clk480m_hw;
+	struct regulator	*vbus_host;
+	const struct rockchip_usb2phy_cfg	*phy_cfg;
+	struct rockchip_usb2phy_port	ports[USB2PHY_NUM_PORTS];
+};
+
+static inline int property_enable(struct rockchip_usb2phy *rphy,
+				  const struct usb2phy_reg *reg, bool en)
+{
+	unsigned int val, mask, tmp;
+
+	tmp = en ? reg->enable : reg->disable;
+	mask = GENMASK(reg->bitend, reg->bitstart);
+	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
+
+	return regmap_write(rphy->grf, reg->offset, val);
+}
+
+static inline bool property_enabled(struct rockchip_usb2phy *rphy,
+				    const struct usb2phy_reg *reg)
+{
+	int ret;
+	unsigned int tmp, orig;
+	unsigned int mask = GENMASK(reg->bitend, reg->bitstart);
+
+	ret = regmap_read(rphy->grf, reg->offset, &orig);
+	if (ret)
+		return false;
+
+	tmp = (orig & mask) >> reg->bitstart;
+	return tmp == reg->enable;
+}
+
+static int rockchip_usb2phy_clk480m_enable(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+	int ret;
+
+	/* turn on 480m clk output if it is off */
+	if (!property_enabled(rphy, &rphy->phy_cfg->clkout_ctl)) {
+		ret = property_enable(rphy, &rphy->phy_cfg->clkout_ctl, true);
+		if (ret)
+			return ret;
+
+		/* waitting for the clk become stable */
+		mdelay(1);
+	}
+
+	return 0;
+}
+
+static void rockchip_usb2phy_clk480m_disable(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+
+	/* turn off 480m clk output */
+	property_enable(rphy, &rphy->phy_cfg->clkout_ctl, false);
+}
+
+static int rockchip_usb2phy_clk480m_enabled(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+
+	return property_enabled(rphy, &rphy->phy_cfg->clkout_ctl);
+}
+
+static unsigned long
+rockchip_usb2phy_clk480m_recalc_rate(struct clk_hw *hw,
+				     unsigned long parent_rate)
+{
+	return 480000000;
+}
+
+static const struct clk_ops rockchip_usb2phy_clkout_ops = {
+	.enable = rockchip_usb2phy_clk480m_enable,
+	.disable = rockchip_usb2phy_clk480m_disable,
+	.is_enabled = rockchip_usb2phy_clk480m_enabled,
+	.recalc_rate = rockchip_usb2phy_clk480m_recalc_rate,
+};
+
+static void rockchip_usb2phy_clk480m_unregister(void *data)
+{
+	struct rockchip_usb2phy *rphy = data;
+
+	of_clk_del_provider(rphy->dev->of_node);
+	clk_unregister(rphy->clk480m);
+
+	if (rphy->clk)
+		clk_put(rphy->clk);
+}
+
+static int
+rockchip_usb2phy_clk480m_register(struct rockchip_usb2phy *rphy)
+{
+	struct device_node *node = rphy->dev->of_node;
+	struct clk_init_data init;
+	const char *clk_name;
+	int ret;
+
+	init.flags = 0;
+	init.name = "clk_usbphy_480m";
+	init.ops = &rockchip_usb2phy_clkout_ops;
+
+	/* optional override of the clockname */
+	of_property_read_string(node, "clock-output-names", &init.name);
+
+	rphy->clk = of_clk_get_by_name(node, "phyclk");
+	if (IS_ERR(rphy->clk)) {
+		rphy->clk = NULL;
+		init.parent_names = NULL;
+		init.num_parents = 0;
+	} else {
+		clk_name = __clk_get_name(rphy->clk);
+		init.parent_names = &clk_name;
+		init.num_parents = 1;
+	}
+
+	rphy->clk480m_hw.init = &init;
+
+	/* register the clock */
+	rphy->clk480m = clk_register(rphy->dev, &rphy->clk480m_hw);
+	if (IS_ERR(rphy->clk480m)) {
+		ret = PTR_ERR(rphy->clk480m);
+		goto err_register;
+	}
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, rphy->clk480m);
+	if (ret < 0)
+		goto err_clk_provider;
+
+	ret = devm_add_action(rphy->dev, rockchip_usb2phy_clk480m_unregister,
+			      rphy);
+	if (ret < 0)
+		goto err_unreg_action;
+
+	return 0;
+
+err_unreg_action:
+	of_clk_del_provider(node);
+err_clk_provider:
+	clk_unregister(rphy->clk480m);
+err_register:
+	if (rphy->clk)
+		clk_put(rphy->clk);
+	return ret;
+}
+
+static int rockchip_usb2phy_init(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	if (rport->port_id == USB2PHY_PORT_HOST) {
+		/* clear linestate and enable linestate detect irq */
+		mutex_lock(&rport->mutex);
+
+		ret = property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+		if (ret) {
+			mutex_unlock(&rport->mutex);
+			return ret;
+		}
+
+		ret = property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+		if (ret) {
+			mutex_unlock(&rport->mutex);
+			return ret;
+		}
+
+		mutex_unlock(&rport->mutex);
+		schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
+	}
+
+	return 0;
+}
+
+static int rockchip_usb2phy_resume(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	dev_dbg(&rport->phy->dev, "port resume\n");
+
+	ret = clk_prepare_enable(rphy->clk480m);
+	if (ret)
+		return ret;
+
+	ret = property_enable(rphy, &rport->port_cfg->phy_sus, false);
+	if (ret)
+		return ret;
+
+	rport->suspended = false;
+	return 0;
+}
+
+static int rockchip_usb2phy_suspend(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	dev_dbg(&rport->phy->dev, "port suspend\n");
+
+	ret = property_enable(rphy, &rport->port_cfg->phy_sus, true);
+	if (ret)
+		return ret;
+
+	rport->suspended = true;
+	clk_disable_unprepare(rphy->clk480m);
+	return 0;
+}
+
+static int rockchip_usb2phy_exit(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+
+	if (rport->port_id == USB2PHY_PORT_HOST)
+		cancel_delayed_work_sync(&rport->sm_work);
+
+	return 0;
+}
+
+static const struct phy_ops rockchip_usb2phy_ops = {
+	.init		= rockchip_usb2phy_init,
+	.exit		= rockchip_usb2phy_exit,
+	.power_on	= rockchip_usb2phy_resume,
+	.power_off	= rockchip_usb2phy_suspend,
+	.owner		= THIS_MODULE,
+};
+
+/*
+ * The function manage host-phy port state and suspend/resume phy port
+ * to save power.
+ *
+ * we rely on utmi_linestate and utmi_hostdisconnect to identify whether
+ * FS/HS is disconnect or not. Besides, we do not need care it is FS
+ * disconnected or HS disconnected, actually, we just only need get the
+ * device is disconnected at last through rearm the delayed work,
+ * to suspend the phy port in _PHY_STATE_DISCONNECT_ case.
+ *
+ * NOTE: It may invoke *phy_suspend or *phy_resume which will invoke some
+ * clk related APIs, so do not invoke it from interrupt context directly.
+ */
+static void rockchip_usb2phy_sm_work(struct work_struct *work)
+{
+	struct rockchip_usb2phy_port *rport =
+		container_of(work, struct rockchip_usb2phy_port, sm_work.work);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+	unsigned int sh = rport->port_cfg->utmi_hstdet.bitend -
+			  rport->port_cfg->utmi_hstdet.bitstart + 1;
+	unsigned int ul, uhd, state;
+	unsigned int ul_mask, uhd_mask;
+	int ret;
+
+	mutex_lock(&rport->mutex);
+
+	ret = regmap_read(rphy->grf, rport->port_cfg->utmi_ls.offset, &ul);
+	if (ret < 0)
+		goto next_schedule;
+
+	ret = regmap_read(rphy->grf, rport->port_cfg->utmi_hstdet.offset,
+			  &uhd);
+	if (ret < 0)
+		goto next_schedule;
+
+	uhd_mask = GENMASK(rport->port_cfg->utmi_hstdet.bitend,
+			   rport->port_cfg->utmi_hstdet.bitstart);
+	ul_mask = GENMASK(rport->port_cfg->utmi_ls.bitend,
+			  rport->port_cfg->utmi_ls.bitstart);
+
+	/* stitch on utmi_ls and utmi_hstdet as phy state */
+	state = ((uhd & uhd_mask) >> rport->port_cfg->utmi_hstdet.bitstart) |
+		(((ul & ul_mask) >> rport->port_cfg->utmi_ls.bitstart) << sh);
+
+	switch (state) {
+	case PHY_STATE_HS_ONLINE:
+		dev_dbg(&rport->phy->dev, "HS online\n");
+		break;
+	case PHY_STATE_FS_CONNECT:
+		/*
+		 * For FS device, the online state share with connect state
+		 * from utmi_ls and utmi_hstdet register, so we distinguish
+		 * them via suspended flag.
+		 */
+		if (!rport->suspended) {
+			dev_dbg(&rport->phy->dev, "FS online\n");
+			break;
+		}
+		/* fall through */
+	case PHY_STATE_HS_CONNECT:
+		if (rport->suspended) {
+			dev_dbg(&rport->phy->dev, "HS/FS connected\n");
+			rockchip_usb2phy_resume(rport->phy);
+			rport->suspended = false;
+		}
+		break;
+	case PHY_STATE_DISCONNECT:
+		if (!rport->suspended) {
+			dev_dbg(&rport->phy->dev, "HS/FS disconnected\n");
+			rockchip_usb2phy_suspend(rport->phy);
+			rport->suspended = true;
+		}
+
+		/*
+		 * activate the linestate detection to get the next device
+		 * plug-in irq.
+		 */
+		property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+		property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+
+		/*
+		 * we don't need to rearm the delayed work when the phy port
+		 * is suspended.
+		 */
+		mutex_unlock(&rport->mutex);
+		return;
+	default:
+		dev_dbg(&rport->phy->dev, "unknown phy state\n");
+		break;
+	}
+
+next_schedule:
+	mutex_unlock(&rport->mutex);
+	schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
+}
+
+static irqreturn_t rockchip_usb2phy_linestate_irq(int irq, void *data)
+{
+	struct rockchip_usb2phy_port *rport = data;
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+
+	if (!property_enabled(rphy, &rport->port_cfg->ls_det_st))
+		return IRQ_NONE;
+
+	mutex_lock(&rport->mutex);
+
+	/* disable linestate detect irq and clear its status */
+	property_enable(rphy, &rport->port_cfg->ls_det_en, false);
+	property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+
+	mutex_unlock(&rport->mutex);
+
+	/*
+	 * In this case for host phy port, a new device is plugged in,
+	 * meanwhile, if the phy port is suspended, we need rearm the work to
+	 * resume it and mange its states; otherwise, we do nothing about that.
+	 */
+	if (rport->suspended && rport->port_id == USB2PHY_PORT_HOST)
+		rockchip_usb2phy_sm_work(&rport->sm_work.work);
+
+	return IRQ_HANDLED;
+}
+
+static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
+					   struct rockchip_usb2phy_port *rport,
+					   struct device_node *child_np)
+{
+	int ret;
+
+	rport->port_id = USB2PHY_PORT_HOST;
+	rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_HOST];
+
+	mutex_init(&rport->mutex);
+	INIT_DELAYED_WORK(&rport->sm_work, rockchip_usb2phy_sm_work);
+
+	rport->ls_irq = of_irq_get_byname(child_np, "linestate");
+	if (rport->ls_irq < 0) {
+		dev_err(rphy->dev, "no linestate irq provided\n");
+		return rport->ls_irq;
+	}
+
+	ret = devm_request_threaded_irq(rphy->dev, rport->ls_irq, NULL,
+					rockchip_usb2phy_linestate_irq,
+					IRQF_ONESHOT,
+					"rockchip_usb2phy", rport);
+	if (ret) {
+		dev_err(rphy->dev, "failed to request irq handle\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rockchip_usb2phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct rockchip_usb2phy *rphy;
+	const struct of_device_id *match;
+	int index, ret;
+
+	rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
+	if (!rphy)
+		return -ENOMEM;
+
+	match = of_match_device(dev->driver->of_match_table, dev);
+	if (!match || !match->data) {
+		dev_err(dev, "phy configs are not assigned!\n");
+		return -EINVAL;
+	}
+
+	if (!dev->parent || !dev->parent->of_node)
+		return -EINVAL;
+
+	rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
+	if (IS_ERR(rphy->grf))
+		return PTR_ERR(rphy->grf);
+
+	rphy->dev = dev;
+	rphy->phy_cfg = match->data;
+	platform_set_drvdata(pdev, rphy);
+
+	ret = rockchip_usb2phy_clk480m_register(rphy);
+	if (ret) {
+		dev_err(dev, "failed to register 480m output clock\n");
+		return ret;
+	}
+
+	rphy->vbus_host = devm_regulator_get_optional(dev, "vbus_host");
+	if (IS_ERR(rphy->vbus_host)) {
+		ret = PTR_ERR(rphy->vbus_host);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		dev_info(dev, "vbus_host regulator is not assigned!\n");
+		rphy->vbus_host = NULL;
+	} else {
+		ret = regulator_enable(rphy->vbus_host);
+		if (ret)
+			return ret;
+	}
+
+	index = 0;
+	for_each_available_child_of_node(np, child_np) {
+		struct rockchip_usb2phy_port *rport = &rphy->ports[index];
+		struct phy *phy;
+
+		phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			ret = PTR_ERR(phy);
+			goto put_child;
+		}
+
+		rport->phy = phy;
+
+		/* initialize otg/host port separately */
+		if (!of_node_cmp(child_np->name, "host-port")) {
+			ret = rockchip_usb2phy_host_port_init(rphy, rport,
+							      child_np);
+			if (ret)
+				goto put_child;
+		}
+
+		phy_set_drvdata(rport->phy, rport);
+
+		/* to prevent out of boundary */
+		if (++index >= rphy->phy_cfg->num_ports)
+			break;
+	}
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+
+put_child:
+	of_node_put(child_np);
+	return ret;
+}
+
+static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs = {
+	.num_ports	= 2,
+	.clkout_ctl	= { 0x0724, 15, 15, 1, 0 },
+	.port_cfgs	= {
+		[USB2PHY_PORT_HOST] = {
+			.phy_sus	= { 0x0728, 15, 0, 0, 0x1d1 },
+			.ls_det_en	= { 0x0680, 4, 4, 0, 1 },
+			.ls_det_st	= { 0x0690, 4, 4, 0, 1 },
+			.ls_det_clr	= { 0x06a0, 4, 4, 0, 1 },
+			.utmi_ls	= { 0x049c, 14, 13, 0, 1 },
+			.utmi_hstdet	= { 0x049c, 12, 12, 0, 1 }
+		}
+	},
+};
+
+static const struct of_device_id rockchip_usb2phy_dt_match[] = {
+	{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
+	{}
+};
+MODULE_DEVICE_TABLE(of, rockchip_usb2phy_dt_match);
+
+static struct platform_driver rockchip_usb2phy_driver = {
+	.probe		= rockchip_usb2phy_probe,
+	.driver		= {
+		.name	= "rockchip-usb2phy",
+		.of_match_table = rockchip_usb2phy_dt_match,
+	},
+};
+module_platform_driver(rockchip_usb2phy_driver);
+
+MODULE_AUTHOR("Frank Wang <frank.wang@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip USB2.0 PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
1.7.9.5

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-06  9:20 ` [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY Frank Wang
@ 2016-06-06 11:27   ` Mark Rutland
  2016-06-06 12:33     ` Heiko Stübner
  0 siblings, 1 reply; 14+ messages in thread
From: Mark Rutland @ 2016-06-06 11:27 UTC (permalink / raw)
  To: Frank Wang
  Cc: heiko, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, ijc+devicetree, galak, linux-kernel, devicetree,
	linux-usb, linux-rockchip, xzy.xu, kever.yang, huangtao,
	william.wu

On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> ---
> 
> Changes in v3:
>  - Added 'clocks' and 'clock-names' optional properties.
>  - Specified 'otg-port' and 'host-port' as the sub-node name.
> 
> Changes in v2:
>  - Changed vbus_host optional property from gpio to regulator.
>  - Specified vbus_otg-supply optional property.
>  - Specified otg_id and otg_bvalid property.
> 
>  .../bindings/phy/phy-rockchip-inno-usb2.txt        |   60 ++++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> new file mode 100644
> index 0000000..0b4bbbb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> @@ -0,0 +1,60 @@
> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
> +
> +Required properties (phy (parent) node):
> + - compatible : should be one of the listed compatibles:
> +	* "rockchip,rk3366-usb2phy"
> +	* "rockchip,rk3399-usb2phy"
> + - #clock-cells : should be 0.
> + - clock-output-names : specify the 480m output clock name.
> +
> +Optional properties:
> + - clocks : phandle + phy specifier pair, for the input clock of phy.
> + - clock-names : input clock name of phy, must be "phyclk".
> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.

Nit: s/_/-/ here.

Otherwise the rest of this looks generally fine, though I'm confused as
to how you address the programming interface(s), given none are
described.

Thanks,
Mark.

> +
> +Required nodes : a sub-node is required for each port the phy provides.
> +		 The sub-node name is used to identify host or otg port,
> +		 and shall be the following entries:
> +	* "otg-port" : the name of otg port.
> +	* "host-port" : the name of host port.
> +
> +Required properties (port (child) node):
> + - #phy-cells : must be 0. See ./phy-bindings.txt for details.
> + - interrupts : specify an interrupt for each entry in interrupt-names.
> + - interrupt-names : a list which shall be the following entries:
> +	* "otg_id" : for the otg id interrupt.
> +	* "otg_bvalid" : for the otg vbus interrupt.
> +	* "linestate" : for the host/otg linestate interrupt.
> +
> +Example:
> +
> +grf: syscon@ff770000 {
> +	compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +...
> +
> +	u2phy: usb2-phy {
> +		compatible = "rockchip,rk3366-usb2phy";
> +		#clock-cells = <0>;
> +		clock-output-names = "sclk_otgphy0_480m";
> +
> +		u2phy_otg: otg-port {
> +			#phy-cells = <0>;
> +			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "otg_id", "otg_bvalid", "linestate";
> +			status = "okay";
> +		};
> +
> +		u2phy_host: host-port {
> +			#phy-cells = <0>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "linestate";
> +			status = "okay";
> +		};
> +	};
> +};
> -- 
> 1.7.9.5
> 
> 

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-06 11:27   ` Mark Rutland
@ 2016-06-06 12:33     ` Heiko Stübner
  2016-06-07  2:59       ` Frank Wang
  0 siblings, 1 reply; 14+ messages in thread
From: Heiko Stübner @ 2016-06-06 12:33 UTC (permalink / raw)
  To: Mark Rutland
  Cc: Frank Wang, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, ijc+devicetree, galak, linux-kernel, devicetree,
	linux-usb, linux-rockchip, xzy.xu, kever.yang, huangtao,
	william.wu

Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
> > Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> > ---
> > 
> > Changes in v3:
> >  - Added 'clocks' and 'clock-names' optional properties.
> >  - Specified 'otg-port' and 'host-port' as the sub-node name.
> > 
> > Changes in v2:
> >  - Changed vbus_host optional property from gpio to regulator.
> >  - Specified vbus_otg-supply optional property.
> >  - Specified otg_id and otg_bvalid property.
> >  
> >  .../bindings/phy/phy-rockchip-inno-usb2.txt        |   60
> >  ++++++++++++++++++++ 1 file changed, 60 insertions(+)
> >  create mode 100644
> >  Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt> 
> > diff --git
> > a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
> > file mode 100644
> > index 0000000..0b4bbbb
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > @@ -0,0 +1,60 @@
> > +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
> > +
> > +Required properties (phy (parent) node):
> > + - compatible : should be one of the listed compatibles:
> > +	* "rockchip,rk3366-usb2phy"
> > +	* "rockchip,rk3399-usb2phy"
> > + - #clock-cells : should be 0.
> > + - clock-output-names : specify the 480m output clock name.
> > +
> > +Optional properties:
> > + - clocks : phandle + phy specifier pair, for the input clock of phy.
> > + - clock-names : input clock name of phy, must be "phyclk".
> > + - vbus_host-supply : phandle to a regulator that supplies host vbus.
> > + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
> 
> Nit: s/_/-/ here.

Something I only stumbled over yesterday for the first time on my rk3288-
popmetal: The phy subnodes seem to be able to use a generic phy-supply
property from inside the phy-core itself, see:

https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aaf6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597

for my WIP code for that other board.


> Otherwise the rest of this looks generally fine, though I'm confused as
> to how you address the programming interface(s), given none are
> described.

I think that comes generally down to phy_power_on and phy_power_off from the
host driver (ehci / dwc2 / whatever) using the generic phy interface. The usb2
phys on Rockchip SoCs seem always pretty easy to handle, while the new
additional typeC phy seems to require more work


Heiko

> > +
> > +Required nodes : a sub-node is required for each port the phy provides.
> > +		 The sub-node name is used to identify host or otg port,
> > +		 and shall be the following entries:
> > +	* "otg-port" : the name of otg port.
> > +	* "host-port" : the name of host port.
> > +
> > +Required properties (port (child) node):
> > + - #phy-cells : must be 0. See ./phy-bindings.txt for details.
> > + - interrupts : specify an interrupt for each entry in interrupt-names.
> > + - interrupt-names : a list which shall be the following entries:
> > +	* "otg_id" : for the otg id interrupt.
> > +	* "otg_bvalid" : for the otg vbus interrupt.
> > +	* "linestate" : for the host/otg linestate interrupt.
> > +
> > +Example:
> > +
> > +grf: syscon@ff770000 {
> > +	compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
> > +	#address-cells = <1>;
> > +	#size-cells = <1>;
> > +
> > +...
> > +
> > +	u2phy: usb2-phy {
> > +		compatible = "rockchip,rk3366-usb2phy";
> > +		#clock-cells = <0>;
> > +		clock-output-names = "sclk_otgphy0_480m";
> > +
> > +		u2phy_otg: otg-port {
> > +			#phy-cells = <0>;
> > +			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
> > +				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
> > +				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> > +			interrupt-names = "otg_id", "otg_bvalid", "linestate";
> > +			status = "okay";
> > +		};
> > +
> > +		u2phy_host: host-port {
> > +			#phy-cells = <0>;
> > +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> > +			interrupt-names = "linestate";
> > +			status = "okay";
> > +		};
> > +	};
> > +};

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-06 12:33     ` Heiko Stübner
@ 2016-06-07  2:59       ` Frank Wang
  2016-06-07  3:31         ` Frank Wang
  0 siblings, 1 reply; 14+ messages in thread
From: Frank Wang @ 2016-06-07  2:59 UTC (permalink / raw)
  To: Heiko Stübner, Mark Rutland
  Cc: dianders, linux, groeck, jwerner, kishon, robh+dt, pawel.moll,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, kever.yang, huangtao, william.wu,
	frank.wang

Hi Heiko & Mark,

On 2016/6/6 20:33, Heiko Stübner wrote:
> Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
>> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
>>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>>> ---
>>>
>>> Changes in v3:
>>>   - Added 'clocks' and 'clock-names' optional properties.
>>>   - Specified 'otg-port' and 'host-port' as the sub-node name.
>>>
>>> Changes in v2:
>>>   - Changed vbus_host optional property from gpio to regulator.
>>>   - Specified vbus_otg-supply optional property.
>>>   - Specified otg_id and otg_bvalid property.
>>>   
>>>   .../bindings/phy/phy-rockchip-inno-usb2.txt        |   60
>>>   ++++++++++++++++++++ 1 file changed, 60 insertions(+)
>>>   create mode 100644
>>>   Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt>
>>> diff --git
>>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
>>> file mode 100644
>>> index 0000000..0b4bbbb
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>> @@ -0,0 +1,60 @@
>>> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
>>> +
>>> +Required properties (phy (parent) node):
>>> + - compatible : should be one of the listed compatibles:
>>> +	* "rockchip,rk3366-usb2phy"
>>> +	* "rockchip,rk3399-usb2phy"
>>> + - #clock-cells : should be 0.
>>> + - clock-output-names : specify the 480m output clock name.
>>> +
>>> +Optional properties:
>>> + - clocks : phandle + phy specifier pair, for the input clock of phy.
>>> + - clock-names : input clock name of phy, must be "phyclk".
>>> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
>>> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
>> Nit: s/_/-/ here.
> Something I only stumbled over yesterday for the first time on my rk3288-
> popmetal: The phy subnodes seem to be able to use a generic phy-supply
> property from inside the phy-core itself, see:
>
> https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aaf6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597
>
> for my WIP code for that other board.
>

Ah, good comments! I will try later, if it is practicable, I shall 
correct it into the next patches (patch v4).

>> Otherwise the rest of this looks generally fine, though I'm confused as
>> to how you address the programming interface(s), given none are
>> described.
> I think that comes generally down to phy_power_on and phy_power_off from the
> host driver (ehci / dwc2 / whatever) using the generic phy interface. The usb2
> phys on Rockchip SoCs seem always pretty easy to handle, while the new
> additional typeC phy seems to require more work
>

Yeah, just like that.

>
>
>>> +
>>> +Required nodes : a sub-node is required for each port the phy provides.
>>> +		 The sub-node name is used to identify host or otg port,
>>> +		 and shall be the following entries:
>>> +	* "otg-port" : the name of otg port.
>>> +	* "host-port" : the name of host port.
>>> +
>>> +Required properties (port (child) node):
>>> + - #phy-cells : must be 0. See ./phy-bindings.txt for details.
>>> + - interrupts : specify an interrupt for each entry in interrupt-names.
>>> + - interrupt-names : a list which shall be the following entries:
>>> +	* "otg_id" : for the otg id interrupt.
>>> +	* "otg_bvalid" : for the otg vbus interrupt.
>>> +	* "linestate" : for the host/otg linestate interrupt.
>>> +
>>> +Example:
>>> +
>>> +grf: syscon@ff770000 {
>>> +	compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
>>> +	#address-cells = <1>;
>>> +	#size-cells = <1>;
>>> +
>>> +...
>>> +
>>> +	u2phy: usb2-phy {
>>> +		compatible = "rockchip,rk3366-usb2phy";
>>> +		#clock-cells = <0>;
>>> +		clock-output-names = "sclk_otgphy0_480m";
>>> +
>>> +		u2phy_otg: otg-port {
>>> +			#phy-cells = <0>;
>>> +			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
>>> +				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>>> +				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
>>> +			interrupt-names = "otg_id", "otg_bvalid", "linestate";
>>> +			status = "okay";
>>> +		};
>>> +
>>> +		u2phy_host: host-port {
>>> +			#phy-cells = <0>;
>>> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
>>> +			interrupt-names = "linestate";
>>> +			status = "okay";
>>> +		};
>>> +	};
>>> +};

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-07  2:59       ` Frank Wang
@ 2016-06-07  3:31         ` Frank Wang
  2016-06-07  7:45           ` Kishon Vijay Abraham I
  2016-06-07  7:59           ` Heiko Stübner
  0 siblings, 2 replies; 14+ messages in thread
From: Frank Wang @ 2016-06-07  3:31 UTC (permalink / raw)
  To: Heiko Stübner, Mark Rutland
  Cc: dianders, linux, groeck, jwerner, kishon, robh+dt, pawel.moll,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, kever.yang, huangtao, william.wu,
	frank.wang

Hi Heiko,

On 2016/6/7 10:59, Frank Wang wrote:
> Hi Heiko & Mark,
>
> On 2016/6/6 20:33, Heiko Stübner wrote:
>> Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
>>> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
>>>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>>>> ---
>>>>
>>>> Changes in v3:
>>>>   - Added 'clocks' and 'clock-names' optional properties.
>>>>   - Specified 'otg-port' and 'host-port' as the sub-node name.
>>>>
>>>> Changes in v2:
>>>>   - Changed vbus_host optional property from gpio to regulator.
>>>>   - Specified vbus_otg-supply optional property.
>>>>   - Specified otg_id and otg_bvalid property.
>>>>     .../bindings/phy/phy-rockchip-inno-usb2.txt        | 60
>>>>   ++++++++++++++++++++ 1 file changed, 60 insertions(+)
>>>>   create mode 100644
>>>> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt>
>>>> diff --git
>>>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
>>>> file mode 100644
>>>> index 0000000..0b4bbbb
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>> @@ -0,0 +1,60 @@
>>>> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
>>>> +
>>>> +Required properties (phy (parent) node):
>>>> + - compatible : should be one of the listed compatibles:
>>>> +    * "rockchip,rk3366-usb2phy"
>>>> +    * "rockchip,rk3399-usb2phy"
>>>> + - #clock-cells : should be 0.
>>>> + - clock-output-names : specify the 480m output clock name.
>>>> +
>>>> +Optional properties:
>>>> + - clocks : phandle + phy specifier pair, for the input clock of phy.
>>>> + - clock-names : input clock name of phy, must be "phyclk".
>>>> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
>>>> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
>>> Nit: s/_/-/ here.
>> Something I only stumbled over yesterday for the first time on my 
>> rk3288-
>> popmetal: The phy subnodes seem to be able to use a generic phy-supply
>> property from inside the phy-core itself, see:
>>
>> https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aaf6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597 
>>
>>
>> for my WIP code for that other board.
>>
>
> Ah, good comments! I will try later, if it is practicable, I shall 
> correct it into the next patches (patch v4).
>

I am sorry to tell you that seems unworkable, because we have two 
sub-nodes (phy-ports) in one parent-node (phy),
what is more, the 'phy-supply' property can only put into parent-node, I 
believe it can not be differentiated types of ports.
I mean vbus for host and otg are separately.

>>> Otherwise the rest of this looks generally fine, though I'm confused as
>>> to how you address the programming interface(s), given none are
>>> described.
>> I think that comes generally down to phy_power_on and phy_power_off 
>> from the
>> host driver (ehci / dwc2 / whatever) using the generic phy interface. 
>> The usb2
>> phys on Rockchip SoCs seem always pretty easy to handle, while the new
>> additional typeC phy seems to require more work
>>
>
> Yeah, just like that.
>
>>
>>
>>>> +
>>>> +Required nodes : a sub-node is required for each port the phy 
>>>> provides.
>>>> +         The sub-node name is used to identify host or otg port,
>>>> +         and shall be the following entries:
>>>> +    * "otg-port" : the name of otg port.
>>>> +    * "host-port" : the name of host port.
>>>> +
>>>> +Required properties (port (child) node):
>>>> + - #phy-cells : must be 0. See ./phy-bindings.txt for details.
>>>> + - interrupts : specify an interrupt for each entry in 
>>>> interrupt-names.
>>>> + - interrupt-names : a list which shall be the following entries:
>>>> +    * "otg_id" : for the otg id interrupt.
>>>> +    * "otg_bvalid" : for the otg vbus interrupt.
>>>> +    * "linestate" : for the host/otg linestate interrupt.
>>>> +
>>>> +Example:
>>>> +
>>>> +grf: syscon@ff770000 {
>>>> +    compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
>>>> +    #address-cells = <1>;
>>>> +    #size-cells = <1>;
>>>> +
>>>> +...
>>>> +
>>>> +    u2phy: usb2-phy {
>>>> +        compatible = "rockchip,rk3366-usb2phy";
>>>> +        #clock-cells = <0>;
>>>> +        clock-output-names = "sclk_otgphy0_480m";
>>>> +
>>>> +        u2phy_otg: otg-port {
>>>> +            #phy-cells = <0>;
>>>> +            interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
>>>> +                     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
>>>> +                     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
>>>> +            interrupt-names = "otg_id", "otg_bvalid", "linestate";
>>>> +            status = "okay";
>>>> +        };
>>>> +
>>>> +        u2phy_host: host-port {
>>>> +            #phy-cells = <0>;
>>>> +            interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
>>>> +            interrupt-names = "linestate";
>>>> +            status = "okay";
>>>> +        };
>>>> +    };
>>>> +};

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-07  3:31         ` Frank Wang
@ 2016-06-07  7:45           ` Kishon Vijay Abraham I
  2016-06-07  8:23             ` Frank Wang
  2016-06-07  7:59           ` Heiko Stübner
  1 sibling, 1 reply; 14+ messages in thread
From: Kishon Vijay Abraham I @ 2016-06-07  7:45 UTC (permalink / raw)
  To: Frank Wang, Heiko Stübner, Mark Rutland
  Cc: dianders, linux, groeck, jwerner, robh+dt, pawel.moll,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, kever.yang, huangtao, william.wu

Hi,

On Tuesday 07 June 2016 09:01 AM, Frank Wang wrote:
> Hi Heiko,
> 
> On 2016/6/7 10:59, Frank Wang wrote:
>> Hi Heiko & Mark,
>>
>> On 2016/6/6 20:33, Heiko Stübner wrote:
>>> Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
>>>> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
>>>>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>>>>> ---
>>>>>
>>>>> Changes in v3:
>>>>>   - Added 'clocks' and 'clock-names' optional properties.
>>>>>   - Specified 'otg-port' and 'host-port' as the sub-node name.
>>>>>
>>>>> Changes in v2:
>>>>>   - Changed vbus_host optional property from gpio to regulator.
>>>>>   - Specified vbus_otg-supply optional property.
>>>>>   - Specified otg_id and otg_bvalid property.
>>>>>     .../bindings/phy/phy-rockchip-inno-usb2.txt        | 60
>>>>>   ++++++++++++++++++++ 1 file changed, 60 insertions(+)
>>>>>   create mode 100644
>>>>> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt>
>>>>> diff --git
>>>>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
>>>>> file mode 100644
>>>>> index 0000000..0b4bbbb
>>>>> --- /dev/null
>>>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>>> @@ -0,0 +1,60 @@
>>>>> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
>>>>> +
>>>>> +Required properties (phy (parent) node):
>>>>> + - compatible : should be one of the listed compatibles:
>>>>> +    * "rockchip,rk3366-usb2phy"
>>>>> +    * "rockchip,rk3399-usb2phy"
>>>>> + - #clock-cells : should be 0.
>>>>> + - clock-output-names : specify the 480m output clock name.
>>>>> +
>>>>> +Optional properties:
>>>>> + - clocks : phandle + phy specifier pair, for the input clock of phy.
>>>>> + - clock-names : input clock name of phy, must be "phyclk".
>>>>> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
>>>>> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
>>>> Nit: s/_/-/ here.
>>> Something I only stumbled over yesterday for the first time on my rk3288-
>>> popmetal: The phy subnodes seem to be able to use a generic phy-supply
>>> property from inside the phy-core itself, see:
>>>
>>> https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aaf6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597
>>>
>>>
>>> for my WIP code for that other board.
>>>
>>
>> Ah, good comments! I will try later, if it is practicable, I shall correct it
>> into the next patches (patch v4).
>>
> 
> I am sorry to tell you that seems unworkable, because we have two sub-nodes
> (phy-ports) in one parent-node (phy),
> what is more, the 'phy-supply' property can only put into parent-node, I
> believe it can not be differentiated types of ports.

'phy-supply' is a property of the phy node and not the 'phy-provider' node. So
IMO this should work. What problem do you see?

Thanks
Kishon

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-07  3:31         ` Frank Wang
  2016-06-07  7:45           ` Kishon Vijay Abraham I
@ 2016-06-07  7:59           ` Heiko Stübner
  1 sibling, 0 replies; 14+ messages in thread
From: Heiko Stübner @ 2016-06-07  7:59 UTC (permalink / raw)
  To: Frank Wang
  Cc: Mark Rutland, dianders, linux, groeck, jwerner, kishon, robh+dt,
	pawel.moll, ijc+devicetree, galak, linux-kernel, devicetree,
	linux-usb, linux-rockchip, xzy.xu, kever.yang, huangtao,
	william.wu

Hi Frank,

Am Dienstag, 7. Juni 2016, 11:31:59 schrieb Frank Wang:
> On 2016/6/7 10:59, Frank Wang wrote:
> > On 2016/6/6 20:33, Heiko Stübner wrote:
> >> Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
> >>> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
> >>>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> >>>> ---
> >>>> 
> >>>> Changes in v3:
> >>>>   - Added 'clocks' and 'clock-names' optional properties.
> >>>>   - Specified 'otg-port' and 'host-port' as the sub-node name.
> >>>> 
> >>>> Changes in v2:
> >>>>   - Changed vbus_host optional property from gpio to regulator.
> >>>>   - Specified vbus_otg-supply optional property.
> >>>>   - Specified otg_id and otg_bvalid property.
> >>>>   
> >>>>     .../bindings/phy/phy-rockchip-inno-usb2.txt        | 60
> >>>>   
> >>>>   ++++++++++++++++++++ 1 file changed, 60 insertions(+)
> >>>>   create mode 100644
> >>>> 
> >>>> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt>
> >>>> diff --git
> >>>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> >>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
> >>>> file mode 100644
> >>>> index 0000000..0b4bbbb
> >>>> --- /dev/null
> >>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> >>>> @@ -0,0 +1,60 @@
> >>>> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
> >>>> +
> >>>> +Required properties (phy (parent) node):
> >>>> + - compatible : should be one of the listed compatibles:
> >>>> +    * "rockchip,rk3366-usb2phy"
> >>>> +    * "rockchip,rk3399-usb2phy"
> >>>> + - #clock-cells : should be 0.
> >>>> + - clock-output-names : specify the 480m output clock name.
> >>>> +
> >>>> +Optional properties:
> >>>> + - clocks : phandle + phy specifier pair, for the input clock of phy.
> >>>> + - clock-names : input clock name of phy, must be "phyclk".
> >>>> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
> >>>> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
> >>> 
> >>> Nit: s/_/-/ here.
> >> 
> >> Something I only stumbled over yesterday for the first time on my
> >> rk3288-
> >> popmetal: The phy subnodes seem to be able to use a generic phy-supply
> >> property from inside the phy-core itself, see:
> >> 
> >> https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aa
> >> f6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597
> >> 
> >> 
> >> for my WIP code for that other board.
> > 
> > Ah, good comments! I will try later, if it is practicable, I shall
> > correct it into the next patches (patch v4).
> 
> I am sorry to tell you that seems unworkable, because we have two
> sub-nodes (phy-ports) in one parent-node (phy),
> what is more, the 'phy-supply' property can only put into parent-node, I
> believe it can not be differentiated types of ports.
> I mean vbus for host and otg are separately.

I would disagree ;-)

If you look in phy-core.c phy_create(), you can see that the struct phy that
gets created, contains its own struct device instance, which then gets the
phys of_node (the host+otg subnodes in this context) attached to it.

The regulator_get_optional then runs on this struct device, thus making lookup
on the subnode. And that works just nicely on my rk3288-popmetal, with its 3
phy subnodes and debugfs/regulator/regulator_summary prints that nicely:

 vcc_sys                          0   12      0  5000mV     0mA  5000mV  5000mV 
    vcc_host_5v                   1    1      0  5000mV     0mA  5000mV  5000mV 
       phy-phy.2                                                    0mV     0mV
    vcc_otg_5v                    1    1      0  5000mV     0mA  5000mV  5000mV 
       phy-phy.0                                                    0mV     0mV
    vcc_sata_5v                   2    1      0  5000mV     0mA  5000mV  5000mV 
       phy-phy.1                                                    0mV     0mV


Heiko

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY
  2016-06-07  7:45           ` Kishon Vijay Abraham I
@ 2016-06-07  8:23             ` Frank Wang
  0 siblings, 0 replies; 14+ messages in thread
From: Frank Wang @ 2016-06-07  8:23 UTC (permalink / raw)
  To: Kishon Vijay Abraham I, Heiko Stübner, Mark Rutland
  Cc: dianders, linux, groeck, jwerner, robh+dt, pawel.moll,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, kever.yang, huangtao, william.wu,
	frank.wang

Hi Kishon & Heiko,

On 2016/6/7 15:45, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Tuesday 07 June 2016 09:01 AM, Frank Wang wrote:
>> Hi Heiko,
>>
>> On 2016/6/7 10:59, Frank Wang wrote:
>>> Hi Heiko & Mark,
>>>
>>> On 2016/6/6 20:33, Heiko Stübner wrote:
>>>> Am Montag, 6. Juni 2016, 12:27:54 schrieb Mark Rutland:
>>>>> On Mon, Jun 06, 2016 at 05:20:03PM +0800, Frank Wang wrote:
>>>>>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>>>>>> ---
>>>>>>
>>>>>> Changes in v3:
>>>>>>    - Added 'clocks' and 'clock-names' optional properties.
>>>>>>    - Specified 'otg-port' and 'host-port' as the sub-node name.
>>>>>>
>>>>>> Changes in v2:
>>>>>>    - Changed vbus_host optional property from gpio to regulator.
>>>>>>    - Specified vbus_otg-supply optional property.
>>>>>>    - Specified otg_id and otg_bvalid property.
>>>>>>      .../bindings/phy/phy-rockchip-inno-usb2.txt        | 60
>>>>>>    ++++++++++++++++++++ 1 file changed, 60 insertions(+)
>>>>>>    create mode 100644
>>>>>> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt>
>>>>>> diff --git
>>>>>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt new
>>>>>> file mode 100644
>>>>>> index 0000000..0b4bbbb
>>>>>> --- /dev/null
>>>>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>>>>>> @@ -0,0 +1,60 @@
>>>>>> +ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
>>>>>> +
>>>>>> +Required properties (phy (parent) node):
>>>>>> + - compatible : should be one of the listed compatibles:
>>>>>> +    * "rockchip,rk3366-usb2phy"
>>>>>> +    * "rockchip,rk3399-usb2phy"
>>>>>> + - #clock-cells : should be 0.
>>>>>> + - clock-output-names : specify the 480m output clock name.
>>>>>> +
>>>>>> +Optional properties:
>>>>>> + - clocks : phandle + phy specifier pair, for the input clock of phy.
>>>>>> + - clock-names : input clock name of phy, must be "phyclk".
>>>>>> + - vbus_host-supply : phandle to a regulator that supplies host vbus.
>>>>>> + - vbus_otg-supply : phandle to a regulator that supplies otg vbus.
>>>>> Nit: s/_/-/ here.
>>>> Something I only stumbled over yesterday for the first time on my rk3288-
>>>> popmetal: The phy subnodes seem to be able to use a generic phy-supply
>>>> property from inside the phy-core itself, see:
>>>>
>>>> https://github.com/mmind/linux-rockchip/commit/93739f521fc65f44524b00c9aaf6db46bca94e02#diff-ddf3e45ebb753d6debf57022003a1a57R597
>>>>
>>>>
>>>> for my WIP code for that other board.
>>>>
>>> Ah, good comments! I will try later, if it is practicable, I shall correct it
>>> into the next patches (patch v4).
>>>
>> I am sorry to tell you that seems unworkable, because we have two sub-nodes
>> (phy-ports) in one parent-node (phy),
>> what is more, the 'phy-supply' property can only put into parent-node, I
>> believe it can not be differentiated types of ports.
> 'phy-supply' is a property of the phy node and not the 'phy-provider' node. So
> IMO this should work. What problem do you see?

Sorry, I think I must have made a wrong phandle of phy-port name in 
*.dts before.
Yes, It works now, thanks for your reminding.

@Heiko,
I have just received your another mail, thanks again for your detail 
explanation.

I will correct it in the next patches (patch v4).

BR.
Frank

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy
  2016-06-06  9:20 ` [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy Frank Wang
@ 2016-06-07  9:54   ` Heiko Stübner
  2016-06-07 13:19     ` Guenter Roeck
  0 siblings, 1 reply; 14+ messages in thread
From: Heiko Stübner @ 2016-06-07  9:54 UTC (permalink / raw)
  To: Frank Wang
  Cc: dianders, linux, groeck, jwerner, kishon, robh+dt, pawel.moll,
	mark.rutland, ijc+devicetree, galak, linux-kernel, devicetree,
	linux-usb, linux-rockchip, xzy.xu, kever.yang, huangtao,
	william.wu

Hi Frank,

Am Montag, 6. Juni 2016, 17:20:04 schrieb Frank Wang:
> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
> than rk3288 and before, and most of phy-related registers are also
> different from the past, so a new phy driver is required necessarily.
> 
> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> ---

[...]

> +static int rockchip_usb2phy_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = dev->of_node;
> +	struct device_node *child_np;
> +	struct phy_provider *provider;
> +	struct rockchip_usb2phy *rphy;
> +	const struct of_device_id *match;
> +	int index, ret;
> +
> +	rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
> +	if (!rphy)
> +		return -ENOMEM;
> +
> +	match = of_match_device(dev->driver->of_match_table, dev);
> +	if (!match || !match->data) {
> +		dev_err(dev, "phy configs are not assigned!\n");
> +		return -EINVAL;
> +	}
> +
> +	if (!dev->parent || !dev->parent->of_node)
> +		return -EINVAL;
> +
> +	rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
> +	if (IS_ERR(rphy->grf))
> +		return PTR_ERR(rphy->grf);
> +
> +	rphy->dev = dev;
> +	rphy->phy_cfg = match->data;
> +	platform_set_drvdata(pdev, rphy);
> +
> +	ret = rockchip_usb2phy_clk480m_register(rphy);
> +	if (ret) {
> +		dev_err(dev, "failed to register 480m output clock\n");
> +		return ret;
> +	}
> +
> +	rphy->vbus_host = devm_regulator_get_optional(dev, "vbus_host");
> +	if (IS_ERR(rphy->vbus_host)) {
> +		ret = PTR_ERR(rphy->vbus_host);
> +		if (ret == -EPROBE_DEFER)
> +			return ret;
> +
> +		dev_info(dev, "vbus_host regulator is not assigned!\n");
> +		rphy->vbus_host = NULL;
> +	} else {
> +		ret = regulator_enable(rphy->vbus_host);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	index = 0;
> +	for_each_available_child_of_node(np, child_np) {
> +		struct rockchip_usb2phy_port *rport = &rphy->ports[index];
> +		struct phy *phy;
> +
> +		phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
> +		if (IS_ERR(phy)) {
> +			dev_err(dev, "failed to create phy\n");
> +			ret = PTR_ERR(phy);
> +			goto put_child;
> +		}
> +
> +		rport->phy = phy;
> +
> +		/* initialize otg/host port separately */
> +		if (!of_node_cmp(child_np->name, "host-port")) {
> +			ret = rockchip_usb2phy_host_port_init(rphy, rport,
> +							      child_np);
> +			if (ret)
> +				goto put_child;
> +		}
> +
> +		phy_set_drvdata(rport->phy, rport);
> +
> +		/* to prevent out of boundary */
> +		if (++index >= rphy->phy_cfg->num_ports)
> +			break;
> +	}
> +
> +	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	return PTR_ERR_OR_ZERO(provider);
> +
> +put_child:
> +	of_node_put(child_np);
> +	return ret;
> +}
> +
> +static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs = {
> +	.num_ports	= 2,
> +	.clkout_ctl	= { 0x0724, 15, 15, 1, 0 },
> +	.port_cfgs	= {
> +		[USB2PHY_PORT_HOST] = {
> +			.phy_sus	= { 0x0728, 15, 0, 0, 0x1d1 },
> +			.ls_det_en	= { 0x0680, 4, 4, 0, 1 },
> +			.ls_det_st	= { 0x0690, 4, 4, 0, 1 },
> +			.ls_det_clr	= { 0x06a0, 4, 4, 0, 1 },
> +			.utmi_ls	= { 0x049c, 14, 13, 0, 1 },
> +			.utmi_hstdet	= { 0x049c, 12, 12, 0, 1 }
> +		}
> +	},
> +};

I also realized that the rk3399 has two of those phy-blocks, so I think we'll 
need to adapt your data storage mechanism a tiny bit. Maybe something like
the following:

In the dts:

grf: syscon@ff770000 {
       compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
	...
       u2phy: usb2-phy@700 {
               compatible = "rockchip,rk3366-usb2phy";
		reg = <0x700 0x2c>;
		...
       };
};

In the driver

static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
	{
		.reg = 0x700,
		.num_ports	= 2,
		.clkout_ctl	= { 0x0724, 15, 15, 1, 0 },
		.port_cfgs	= {
			[USB2PHY_PORT_HOST] = {
				.phy_sus	= { 0x0728, 15, 0, 0, 0x1d1 },
				...
			}
		},
	},
};

and in _probe then simply use the correct array entry matching the dts reg 
property.

On the rk3399 this would then probably be

       u2phy0: phy@e450 {
               compatible = "rockchip,rk3366-usb2phy";
		reg = <0xe450 0x10>;
		...
	};

       u2phy1: phy@e460 {
               compatible = "rockchip,rk3366-usb2phy";
		reg = <0xe460 0x10>;
		...
	};


This is slightly similar to what we do with the emmc-phy. But also as the 
usbphys differ in a lot of way, this is really only used to match to the data 
block.

This only affects the match-data selection and the rest of the driver does not 
need to be changed for this.


Heiko


> +static const struct of_device_id rockchip_usb2phy_dt_match[] = {
> +	{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, rockchip_usb2phy_dt_match);
> +
> +static struct platform_driver rockchip_usb2phy_driver = {
> +	.probe		= rockchip_usb2phy_probe,
> +	.driver		= {
> +		.name	= "rockchip-usb2phy",
> +		.of_match_table = rockchip_usb2phy_dt_match,
> +	},
> +};
> +module_platform_driver(rockchip_usb2phy_driver);
> +
> +MODULE_AUTHOR("Frank Wang <frank.wang@rock-chips.com>");
> +MODULE_DESCRIPTION("Rockchip USB2.0 PHY driver");
> +MODULE_LICENSE("GPL v2");

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy
  2016-06-07  9:54   ` Heiko Stübner
@ 2016-06-07 13:19     ` Guenter Roeck
  2016-06-07 14:12       ` Heiko Stübner
  0 siblings, 1 reply; 14+ messages in thread
From: Guenter Roeck @ 2016-06-07 13:19 UTC (permalink / raw)
  To: Heiko Stübner
  Cc: Frank Wang, Douglas Anderson, Guenter Roeck, Guenter Roeck,
	jwerner, kishon, robh+dt, pawel.moll, mark.rutland,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, Kever Yang, huangtao, william.wu

On Tue, Jun 7, 2016 at 2:54 AM, Heiko Stübner <heiko@sntech.de> wrote:
> Hi Frank,
>
> Am Montag, 6. Juni 2016, 17:20:04 schrieb Frank Wang:
>> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
>> than rk3288 and before, and most of phy-related registers are also
>> different from the past, so a new phy driver is required necessarily.
>>
>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>> ---
>
> [...]
>
>> +static int rockchip_usb2phy_probe(struct platform_device *pdev)
>> +{
>> +     struct device *dev = &pdev->dev;
>> +     struct device_node *np = dev->of_node;
>> +     struct device_node *child_np;
>> +     struct phy_provider *provider;
>> +     struct rockchip_usb2phy *rphy;
>> +     const struct of_device_id *match;
>> +     int index, ret;
>> +
>> +     rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
>> +     if (!rphy)
>> +             return -ENOMEM;
>> +
>> +     match = of_match_device(dev->driver->of_match_table, dev);
>> +     if (!match || !match->data) {
>> +             dev_err(dev, "phy configs are not assigned!\n");
>> +             return -EINVAL;
>> +     }
>> +
>> +     if (!dev->parent || !dev->parent->of_node)
>> +             return -EINVAL;
>> +
>> +     rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
>> +     if (IS_ERR(rphy->grf))
>> +             return PTR_ERR(rphy->grf);
>> +
>> +     rphy->dev = dev;
>> +     rphy->phy_cfg = match->data;
>> +     platform_set_drvdata(pdev, rphy);
>> +
>> +     ret = rockchip_usb2phy_clk480m_register(rphy);
>> +     if (ret) {
>> +             dev_err(dev, "failed to register 480m output clock\n");
>> +             return ret;
>> +     }
>> +
>> +     rphy->vbus_host = devm_regulator_get_optional(dev, "vbus_host");
>> +     if (IS_ERR(rphy->vbus_host)) {
>> +             ret = PTR_ERR(rphy->vbus_host);
>> +             if (ret == -EPROBE_DEFER)
>> +                     return ret;
>> +
>> +             dev_info(dev, "vbus_host regulator is not assigned!\n");
>> +             rphy->vbus_host = NULL;
>> +     } else {
>> +             ret = regulator_enable(rphy->vbus_host);
>> +             if (ret)
>> +                     return ret;
>> +     }
>> +
>> +     index = 0;
>> +     for_each_available_child_of_node(np, child_np) {
>> +             struct rockchip_usb2phy_port *rport = &rphy->ports[index];
>> +             struct phy *phy;
>> +
>> +             phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
>> +             if (IS_ERR(phy)) {
>> +                     dev_err(dev, "failed to create phy\n");
>> +                     ret = PTR_ERR(phy);
>> +                     goto put_child;
>> +             }
>> +
>> +             rport->phy = phy;
>> +
>> +             /* initialize otg/host port separately */
>> +             if (!of_node_cmp(child_np->name, "host-port")) {
>> +                     ret = rockchip_usb2phy_host_port_init(rphy, rport,
>> +                                                           child_np);
>> +                     if (ret)
>> +                             goto put_child;
>> +             }
>> +
>> +             phy_set_drvdata(rport->phy, rport);
>> +
>> +             /* to prevent out of boundary */
>> +             if (++index >= rphy->phy_cfg->num_ports)
>> +                     break;
>> +     }
>> +
>> +     provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +     return PTR_ERR_OR_ZERO(provider);
>> +
>> +put_child:
>> +     of_node_put(child_np);
>> +     return ret;
>> +}
>> +
>> +static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs = {
>> +     .num_ports      = 2,
>> +     .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
>> +     .port_cfgs      = {
>> +             [USB2PHY_PORT_HOST] = {
>> +                     .phy_sus        = { 0x0728, 15, 0, 0, 0x1d1 },
>> +                     .ls_det_en      = { 0x0680, 4, 4, 0, 1 },
>> +                     .ls_det_st      = { 0x0690, 4, 4, 0, 1 },
>> +                     .ls_det_clr     = { 0x06a0, 4, 4, 0, 1 },
>> +                     .utmi_ls        = { 0x049c, 14, 13, 0, 1 },
>> +                     .utmi_hstdet    = { 0x049c, 12, 12, 0, 1 }
>> +             }
>> +     },
>> +};
>
> I also realized that the rk3399 has two of those phy-blocks, so I think we'll
> need to adapt your data storage mechanism a tiny bit. Maybe something like
> the following:
>
> In the dts:
>
> grf: syscon@ff770000 {
>        compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
>         ...
>        u2phy: usb2-phy@700 {
>                compatible = "rockchip,rk3366-usb2phy";
>                 reg = <0x700 0x2c>;
>                 ...
>        };
> };
>
> In the driver
>
> static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
>         {
>                 .reg = 0x700,
>                 .num_ports      = 2,
>                 .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
>                 .port_cfgs      = {
>                         [USB2PHY_PORT_HOST] = {
>                                 .phy_sus        = { 0x0728, 15, 0, 0, 0x1d1 },
>                                 ...
>                         }
>                 },
>         },
> };
>
> and in _probe then simply use the correct array entry matching the dts reg
> property.
>
> On the rk3399 this would then probably be
>
>        u2phy0: phy@e450 {
>                compatible = "rockchip,rk3366-usb2phy";
>                 reg = <0xe450 0x10>;
>                 ...
>         };
>
>        u2phy1: phy@e460 {
>                compatible = "rockchip,rk3366-usb2phy";
>                 reg = <0xe460 0x10>;
>                 ...
>         };
>
>
> This is slightly similar to what we do with the emmc-phy. But also as the
> usbphys differ in a lot of way, this is really only used to match to the data
> block.
>
> This only affects the match-data selection and the rest of the driver does not
> need to be changed for this.
>

Would this replace the host-port property ?

Thanks,
Guenter

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy
  2016-06-07 13:19     ` Guenter Roeck
@ 2016-06-07 14:12       ` Heiko Stübner
  2016-06-07 17:19         ` Guenter Roeck
  0 siblings, 1 reply; 14+ messages in thread
From: Heiko Stübner @ 2016-06-07 14:12 UTC (permalink / raw)
  To: Guenter Roeck
  Cc: Frank Wang, Douglas Anderson, Guenter Roeck, Guenter Roeck,
	jwerner, kishon, robh+dt, pawel.moll, mark.rutland,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, Kever Yang, huangtao, william.wu

Hi Guenter,

Am Dienstag, 7. Juni 2016, 06:19:45 schrieb Guenter Roeck:
> On Tue, Jun 7, 2016 at 2:54 AM, Heiko Stübner <heiko@sntech.de> wrote:
> > Hi Frank,
> > 
> > Am Montag, 6. Juni 2016, 17:20:04 schrieb Frank Wang:
> >> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
> >> than rk3288 and before, and most of phy-related registers are also
> >> different from the past, so a new phy driver is required necessarily.
> >> 
> >> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> >> ---
> > 
> > [...]
> > 
> >> +static int rockchip_usb2phy_probe(struct platform_device *pdev)
> >> +{
> >> +     struct device *dev = &pdev->dev;
> >> +     struct device_node *np = dev->of_node;
> >> +     struct device_node *child_np;
> >> +     struct phy_provider *provider;
> >> +     struct rockchip_usb2phy *rphy;
> >> +     const struct of_device_id *match;
> >> +     int index, ret;
> >> +
> >> +     rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
> >> +     if (!rphy)
> >> +             return -ENOMEM;
> >> +
> >> +     match = of_match_device(dev->driver->of_match_table, dev);
> >> +     if (!match || !match->data) {
> >> +             dev_err(dev, "phy configs are not assigned!\n");
> >> +             return -EINVAL;
> >> +     }
> >> +
> >> +     if (!dev->parent || !dev->parent->of_node)
> >> +             return -EINVAL;
> >> +
> >> +     rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
> >> +     if (IS_ERR(rphy->grf))
> >> +             return PTR_ERR(rphy->grf);
> >> +
> >> +     rphy->dev = dev;
> >> +     rphy->phy_cfg = match->data;
> >> +     platform_set_drvdata(pdev, rphy);
> >> +
> >> +     ret = rockchip_usb2phy_clk480m_register(rphy);
> >> +     if (ret) {
> >> +             dev_err(dev, "failed to register 480m output clock\n");
> >> +             return ret;
> >> +     }
> >> +
> >> +     rphy->vbus_host = devm_regulator_get_optional(dev, "vbus_host");
> >> +     if (IS_ERR(rphy->vbus_host)) {
> >> +             ret = PTR_ERR(rphy->vbus_host);
> >> +             if (ret == -EPROBE_DEFER)
> >> +                     return ret;
> >> +
> >> +             dev_info(dev, "vbus_host regulator is not assigned!\n");
> >> +             rphy->vbus_host = NULL;
> >> +     } else {
> >> +             ret = regulator_enable(rphy->vbus_host);
> >> +             if (ret)
> >> +                     return ret;
> >> +     }
> >> +
> >> +     index = 0;
> >> +     for_each_available_child_of_node(np, child_np) {
> >> +             struct rockchip_usb2phy_port *rport = &rphy->ports[index];
> >> +             struct phy *phy;
> >> +
> >> +             phy = devm_phy_create(dev, child_np,
> >> &rockchip_usb2phy_ops);
> >> +             if (IS_ERR(phy)) {
> >> +                     dev_err(dev, "failed to create phy\n");
> >> +                     ret = PTR_ERR(phy);
> >> +                     goto put_child;
> >> +             }
> >> +
> >> +             rport->phy = phy;
> >> +
> >> +             /* initialize otg/host port separately */
> >> +             if (!of_node_cmp(child_np->name, "host-port")) {
> >> +                     ret = rockchip_usb2phy_host_port_init(rphy, rport,
> >> +                                                           child_np);
> >> +                     if (ret)
> >> +                             goto put_child;
> >> +             }
> >> +
> >> +             phy_set_drvdata(rport->phy, rport);
> >> +
> >> +             /* to prevent out of boundary */
> >> +             if (++index >= rphy->phy_cfg->num_ports)
> >> +                     break;
> >> +     }
> >> +
> >> +     provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> >> +     return PTR_ERR_OR_ZERO(provider);
> >> +
> >> +put_child:
> >> +     of_node_put(child_np);
> >> +     return ret;
> >> +}
> >> +
> >> +static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs = {
> >> +     .num_ports      = 2,
> >> +     .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
> >> +     .port_cfgs      = {
> >> +             [USB2PHY_PORT_HOST] = {
> >> +                     .phy_sus        = { 0x0728, 15, 0, 0, 0x1d1 },
> >> +                     .ls_det_en      = { 0x0680, 4, 4, 0, 1 },
> >> +                     .ls_det_st      = { 0x0690, 4, 4, 0, 1 },
> >> +                     .ls_det_clr     = { 0x06a0, 4, 4, 0, 1 },
> >> +                     .utmi_ls        = { 0x049c, 14, 13, 0, 1 },
> >> +                     .utmi_hstdet    = { 0x049c, 12, 12, 0, 1 }
> >> +             }
> >> +     },
> >> +};
> > 
> > I also realized that the rk3399 has two of those phy-blocks, so I think
> > we'll need to adapt your data storage mechanism a tiny bit. Maybe
> > something like the following:
> > 
> > In the dts:
> > 
> > grf: syscon@ff770000 {
> > 
> >        compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
> >        
> >         ...
> >        
> >        u2phy: usb2-phy@700 {
> >        
> >                compatible = "rockchip,rk3366-usb2phy";
> >                
> >                 reg = <0x700 0x2c>;
> >                 ...
> >        
> >        };
> > 
> > };
> > 
> > In the driver
> > 
> > static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
> > 
> >         {
> >         
> >                 .reg = 0x700,
> >                 .num_ports      = 2,
> >                 .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
> >                 .port_cfgs      = {
> >                 
> >                         [USB2PHY_PORT_HOST] = {
> >                         
> >                                 .phy_sus        = { 0x0728, 15, 0, 0,
> >                                 0x1d1 },
> >                                 ...
> >                         
> >                         }
> >                 
> >                 },
> >         
> >         },
> > 
> > };
> > 
> > and in _probe then simply use the correct array entry matching the dts reg
> > property.
> > 
> > On the rk3399 this would then probably be
> > 
> >        u2phy0: phy@e450 {
> >        
> >                compatible = "rockchip,rk3366-usb2phy";
> >                
> >                 reg = <0xe450 0x10>;
> >                 ...
> >         
> >         };
> >        
> >        u2phy1: phy@e460 {
> >        
> >                compatible = "rockchip,rk3366-usb2phy";
> >                
> >                 reg = <0xe460 0x10>;
> >                 ...
> >         
> >         };
> > 
> > This is slightly similar to what we do with the emmc-phy. But also as the
> > usbphys differ in a lot of way, this is really only used to match to the
> > data block.
> > 
> > This only affects the match-data selection and the rest of the driver does
> > not need to be changed for this.
> 
> Would this replace the host-port property ?

nope ... each phy-block has two ports (host + otg). Franks rk3366 has one phy-
block while the rk3399 has two phy blocks (with two ports on each).


Heiko

^ permalink raw reply	[flat|nested] 14+ messages in thread

* Re: [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy
  2016-06-07 14:12       ` Heiko Stübner
@ 2016-06-07 17:19         ` Guenter Roeck
  0 siblings, 0 replies; 14+ messages in thread
From: Guenter Roeck @ 2016-06-07 17:19 UTC (permalink / raw)
  To: Heiko Stübner
  Cc: Guenter Roeck, Frank Wang, Douglas Anderson, Guenter Roeck,
	jwerner, kishon, robh+dt, pawel.moll, mark.rutland,
	ijc+devicetree, galak, linux-kernel, devicetree, linux-usb,
	linux-rockchip, xzy.xu, Kever Yang, huangtao, william.wu

On Tue, Jun 07, 2016 at 04:12:29PM +0200, Heiko Stübner wrote:
> Hi Guenter,
> 
> Am Dienstag, 7. Juni 2016, 06:19:45 schrieb Guenter Roeck:
> > On Tue, Jun 7, 2016 at 2:54 AM, Heiko Stübner <heiko@sntech.de> wrote:
> > > Hi Frank,
> > > 
> > > Am Montag, 6. Juni 2016, 17:20:04 schrieb Frank Wang:
> > >> The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
> > >> than rk3288 and before, and most of phy-related registers are also
> > >> different from the past, so a new phy driver is required necessarily.
> > >> 
> > >> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
> > >> ---
> > > 
> > > [...]
> > > 
> > >> +static int rockchip_usb2phy_probe(struct platform_device *pdev)
> > >> +{
> > >> +     struct device *dev = &pdev->dev;
> > >> +     struct device_node *np = dev->of_node;
> > >> +     struct device_node *child_np;
> > >> +     struct phy_provider *provider;
> > >> +     struct rockchip_usb2phy *rphy;
> > >> +     const struct of_device_id *match;
> > >> +     int index, ret;
> > >> +
> > >> +     rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
> > >> +     if (!rphy)
> > >> +             return -ENOMEM;
> > >> +
> > >> +     match = of_match_device(dev->driver->of_match_table, dev);
> > >> +     if (!match || !match->data) {
> > >> +             dev_err(dev, "phy configs are not assigned!\n");
> > >> +             return -EINVAL;
> > >> +     }
> > >> +
> > >> +     if (!dev->parent || !dev->parent->of_node)
> > >> +             return -EINVAL;
> > >> +
> > >> +     rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
> > >> +     if (IS_ERR(rphy->grf))
> > >> +             return PTR_ERR(rphy->grf);
> > >> +
> > >> +     rphy->dev = dev;
> > >> +     rphy->phy_cfg = match->data;
> > >> +     platform_set_drvdata(pdev, rphy);
> > >> +
> > >> +     ret = rockchip_usb2phy_clk480m_register(rphy);
> > >> +     if (ret) {
> > >> +             dev_err(dev, "failed to register 480m output clock\n");
> > >> +             return ret;
> > >> +     }
> > >> +
> > >> +     rphy->vbus_host = devm_regulator_get_optional(dev, "vbus_host");
> > >> +     if (IS_ERR(rphy->vbus_host)) {
> > >> +             ret = PTR_ERR(rphy->vbus_host);
> > >> +             if (ret == -EPROBE_DEFER)
> > >> +                     return ret;
> > >> +
> > >> +             dev_info(dev, "vbus_host regulator is not assigned!\n");
> > >> +             rphy->vbus_host = NULL;
> > >> +     } else {
> > >> +             ret = regulator_enable(rphy->vbus_host);
> > >> +             if (ret)
> > >> +                     return ret;
> > >> +     }
> > >> +
> > >> +     index = 0;
> > >> +     for_each_available_child_of_node(np, child_np) {
> > >> +             struct rockchip_usb2phy_port *rport = &rphy->ports[index];
> > >> +             struct phy *phy;
> > >> +
> > >> +             phy = devm_phy_create(dev, child_np,
> > >> &rockchip_usb2phy_ops);
> > >> +             if (IS_ERR(phy)) {
> > >> +                     dev_err(dev, "failed to create phy\n");
> > >> +                     ret = PTR_ERR(phy);
> > >> +                     goto put_child;
> > >> +             }
> > >> +
> > >> +             rport->phy = phy;
> > >> +
> > >> +             /* initialize otg/host port separately */
> > >> +             if (!of_node_cmp(child_np->name, "host-port")) {
> > >> +                     ret = rockchip_usb2phy_host_port_init(rphy, rport,
> > >> +                                                           child_np);
> > >> +                     if (ret)
> > >> +                             goto put_child;
> > >> +             }
> > >> +
> > >> +             phy_set_drvdata(rport->phy, rport);
> > >> +
> > >> +             /* to prevent out of boundary */
> > >> +             if (++index >= rphy->phy_cfg->num_ports)
> > >> +                     break;
> > >> +     }
> > >> +
> > >> +     provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> > >> +     return PTR_ERR_OR_ZERO(provider);
> > >> +
> > >> +put_child:
> > >> +     of_node_put(child_np);
> > >> +     return ret;
> > >> +}
> > >> +
> > >> +static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs = {
> > >> +     .num_ports      = 2,
> > >> +     .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
> > >> +     .port_cfgs      = {
> > >> +             [USB2PHY_PORT_HOST] = {
> > >> +                     .phy_sus        = { 0x0728, 15, 0, 0, 0x1d1 },
> > >> +                     .ls_det_en      = { 0x0680, 4, 4, 0, 1 },
> > >> +                     .ls_det_st      = { 0x0690, 4, 4, 0, 1 },
> > >> +                     .ls_det_clr     = { 0x06a0, 4, 4, 0, 1 },
> > >> +                     .utmi_ls        = { 0x049c, 14, 13, 0, 1 },
> > >> +                     .utmi_hstdet    = { 0x049c, 12, 12, 0, 1 }
> > >> +             }
> > >> +     },
> > >> +};
> > > 
> > > I also realized that the rk3399 has two of those phy-blocks, so I think
> > > we'll need to adapt your data storage mechanism a tiny bit. Maybe
> > > something like the following:
> > > 
> > > In the dts:
> > > 
> > > grf: syscon@ff770000 {
> > > 
> > >        compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
> > >        
> > >         ...
> > >        
> > >        u2phy: usb2-phy@700 {
> > >        
> > >                compatible = "rockchip,rk3366-usb2phy";
> > >                
> > >                 reg = <0x700 0x2c>;
> > >                 ...
> > >        
> > >        };
> > > 
> > > };
> > > 
> > > In the driver
> > > 
> > > static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
> > > 
> > >         {
> > >         
> > >                 .reg = 0x700,
> > >                 .num_ports      = 2,
> > >                 .clkout_ctl     = { 0x0724, 15, 15, 1, 0 },
> > >                 .port_cfgs      = {
> > >                 
> > >                         [USB2PHY_PORT_HOST] = {
> > >                         
> > >                                 .phy_sus        = { 0x0728, 15, 0, 0,
> > >                                 0x1d1 },
> > >                                 ...
> > >                         
> > >                         }
> > >                 
> > >                 },
> > >         
> > >         },
> > > 
> > > };
> > > 
> > > and in _probe then simply use the correct array entry matching the dts reg
> > > property.
> > > 
> > > On the rk3399 this would then probably be
> > > 
> > >        u2phy0: phy@e450 {
> > >        
> > >                compatible = "rockchip,rk3366-usb2phy";
> > >                
> > >                 reg = <0xe450 0x10>;
> > >                 ...
> > >         
> > >         };
> > >        
> > >        u2phy1: phy@e460 {
> > >        
> > >                compatible = "rockchip,rk3366-usb2phy";
> > >                
> > >                 reg = <0xe460 0x10>;
> > >                 ...
> > >         
> > >         };
> > > 
> > > This is slightly similar to what we do with the emmc-phy. But also as the
> > > usbphys differ in a lot of way, this is really only used to match to the
> > > data block.
> > > 
> > > This only affects the match-data selection and the rest of the driver does
> > > not need to be changed for this.
> > 
> > Would this replace the host-port property ?
> 
> nope ... each phy-block has two ports (host + otg). Franks rk3366 has one phy-
> block while the rk3399 has two phy blocks (with two ports on each).
> 
Ah, now I understand. Yes, I think you are right, it would make sense
to add this now.

Guenter

^ permalink raw reply	[flat|nested] 14+ messages in thread

end of thread, other threads:[~2016-06-07 17:20 UTC | newest]

Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-06  9:20 [PATCH v3 0/2] Add a new Rockchip usb2 phy driver Frank Wang
2016-06-06  9:20 ` [PATCH v3 1/2] Documentation: bindings: add DT documentation for Rockchip USB2PHY Frank Wang
2016-06-06 11:27   ` Mark Rutland
2016-06-06 12:33     ` Heiko Stübner
2016-06-07  2:59       ` Frank Wang
2016-06-07  3:31         ` Frank Wang
2016-06-07  7:45           ` Kishon Vijay Abraham I
2016-06-07  8:23             ` Frank Wang
2016-06-07  7:59           ` Heiko Stübner
2016-06-06  9:20 ` [PATCH v3 2/2] phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phy Frank Wang
2016-06-07  9:54   ` Heiko Stübner
2016-06-07 13:19     ` Guenter Roeck
2016-06-07 14:12       ` Heiko Stübner
2016-06-07 17:19         ` Guenter Roeck

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).