From: Peter Griffin <peter.griffin@linaro.org>
To: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, kernel@stlinux.com,
maxime.coquelin@st.com, patrice.chotard@st.com,
srinivas.kandagatla@gmail.com, vinod.koul@intel.com,
bjorn.andersson@linaro.org, arnaud.pouliquen@st.com,
arnd@arndb.de
Cc: peter.griffin@linaro.org, lee.jones@linaro.org,
dmaengine@vger.kernel.org, linux-remoteproc@vger.kernel.org,
devicetree@vger.kernel.org
Subject: [PATCH v5 07/18] ARM: STi: DT: STiH407: Add FDMA driver dt nodes.
Date: Tue, 7 Jun 2016 17:19:01 +0100 [thread overview]
Message-ID: <1465316352-20691-8-git-send-email-peter.griffin@linaro.org> (raw)
In-Reply-To: <1465316352-20691-1-git-send-email-peter.griffin@linaro.org>
These nodes are required to get the fdma driver working
on STiH407 based silicon.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
arch/arm/boot/dts/stih407-family.dtsi | 52 +++++++++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
index c47c664..017d670 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/stih407-family.dtsi
@@ -822,5 +822,57 @@
clock-frequency = <600000000>;
st,syscfg = <&syscfg_core 0x224>;
};
+
+ /* fdma audio */
+ fdma0: dma-controller@8e20000 {
+ compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc";
+ reg = <0x8e20000 0x8000>,
+ <0x8e30000 0x3000>,
+ <0x8e37000 0x1000>,
+ <0x8e38000 0x8000>;
+ reg-names = "slimcore", "dmem", "peripherals", "imem";
+ clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>;
+ dma-channels = <16>;
+ #dma-cells = <3>;
+ };
+
+ /* fdma app */
+ fdma1: dma-controller@8e40000 {
+ compatible = "st,stih407-fdma-mpe31-12", "st,slim-rproc";
+ reg = <0x8e40000 0x8000>,
+ <0x8e50000 0x3000>,
+ <0x8e57000 0x1000>,
+ <0x8e58000 0x8000>;
+ reg-names = "slimcore", "dmem", "peripherals", "imem";
+ clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+ <&clk_s_c0_flexgen CLK_TX_ICN_DMU>,
+ <&clk_s_c0_flexgen CLK_TX_ICN_DMU>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+
+ interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>;
+ dma-channels = <16>;
+ #dma-cells = <3>;
+ };
+
+ /* fdma free running */
+ fdma2: dma-controller@8e60000 {
+ compatible = "st,stih407-fdma-mpe31-13", "st,slim-rproc";
+ reg = <0x8e60000 0x8000>,
+ <0x8e70000 0x3000>,
+ <0x8e77000 0x1000>,
+ <0x8e78000 0x8000>;
+ reg-names = "slimcore", "dmem", "peripherals", "imem";
+ interrupts = <GIC_SPI 9 IRQ_TYPE_NONE>;
+ dma-channels = <16>;
+ #dma-cells = <3>;
+ clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+ <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+ <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+ };
};
};
--
1.9.1
next prev parent reply other threads:[~2016-06-07 16:23 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-07 16:18 [PATCH v5 00/18] Add support for FDMA DMA controller and slim core rproc found on STi chipsets Peter Griffin
2016-06-07 16:18 ` [PATCH v5 01/18] remoteproc: make rsc table support optional Peter Griffin
2016-06-07 17:35 ` kbuild test robot
2016-06-07 19:56 ` Bjorn Andersson
2016-06-07 16:18 ` [PATCH v5 02/18] remoteproc: st_slim_rproc: add a slimcore rproc driver Peter Griffin
2016-06-07 17:20 ` kbuild test robot
2016-06-07 16:18 ` [PATCH v5 03/18] MAINTAINERS: Add st slim core rproc driver to STi section Peter Griffin
2016-06-07 16:18 ` [PATCH v5 04/18] dmaengine: st_fdma: Add STMicroelectronics FDMA DT binding documentation Peter Griffin
2016-06-07 16:18 ` [PATCH v5 05/18] dmaengine: st_fdma: Add STMicroelectronics FDMA driver header file Peter Griffin
2016-06-07 16:19 ` [PATCH v5 06/18] dmaengine: st_fdma: Add STMicroelectronics FDMA engine driver support Peter Griffin
2016-06-07 16:19 ` Peter Griffin [this message]
2016-06-07 16:19 ` [PATCH v5 08/18] MAINTAINERS: Add FDMA driver files to STi section Peter Griffin
2016-06-07 16:19 ` [PATCH v5 09/18] ARM: multi_v7_defconfig: Enable STi FDMA driver Peter Griffin
2016-06-07 16:19 ` [PATCH v5 10/18] ASoC: sti: Update DT example to match the driver code Peter Griffin
2016-06-07 16:19 ` [PATCH v5 11/18] ARM: multi_v7_defconfig: Enable STi and simple-card drivers Peter Griffin
2016-06-07 16:19 ` [PATCH v5 12/18] ARM: DT: STiH407: Add i2s_out pinctrl configuration Peter Griffin
2016-06-07 16:19 ` [PATCH v5 13/18] ARM: DT: STiH407: Add i2s_in " Peter Griffin
2016-06-07 16:19 ` [PATCH v5 14/18] ARM: DT: STiH407: Add spdif_out pinctrl config Peter Griffin
2016-06-07 16:19 ` [PATCH v5 15/18] ARM: STi: DT: STiH407: Add sti-sasg-codec dt node Peter Griffin
2016-06-07 16:19 ` [PATCH v5 16/18] ARM: STi: DT: STiH407: Add uniperif player dt nodes Peter Griffin
2016-06-07 16:19 ` [PATCH v5 17/18] ARM: STi: DT: STiH407: Add uniperif reader " Peter Griffin
2016-06-07 16:19 ` [PATCH v5 18/18] ARM: DT: STi: stihxxx-b2120: Add DT nodes for STi audio card Peter Griffin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1465316352-20691-8-git-send-email-peter.griffin@linaro.org \
--to=peter.griffin@linaro.org \
--cc=arnaud.pouliquen@st.com \
--cc=arnd@arndb.de \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=kernel@stlinux.com \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=maxime.coquelin@st.com \
--cc=patrice.chotard@st.com \
--cc=srinivas.kandagatla@gmail.com \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).