linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH 00/48] ARM: at91: rework Atmel TCB drivers
@ 2016-06-10 22:03 Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
                   ` (47 more replies)
  0 siblings, 48 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Antoine Aubert, Daniel Lezcano, devicetree, Douglas Gilbert,
	Fabio Porcedda, Gregory CLEMENT, Gregory Hermant,
	Joachim Eastwood, linux-clk, linux-pwm, Marek Vasut,
	Martin Reimann, Rob Herring, Rodolfo Giometti, Sergio Tanzilli,
	Stephen Boyd, Thierry Reding, Thomas Gleixner, Tim Schendekehl

Hi,

This series reworks the Atmel Timer counter Block drivers. Those blocks
each have 3 counters with 2 channels each and can be used for
multiple functions:
 - timers
 - PWMs
 - Quadrature decoders
 - Stepper motor counters

Up until now, each TCB was fully used by each driver, possibly wasting
counters/channels.

There is a second issue motivating that rework. Until now, the PIT is
still used to boot then later in the boot sequence, the clocksource is
switched to the TCB. This ends up not working well with preempt-rt
because on some SoCs, the PIT interrupt is shared with the DBGU uart.
When using preempt-rt the interrupt flags for the PIT and the DBGU end
up being incompatible.

The whole rework doesn't break the DT ABI for the clocksource as the old
driver is kept anyway for AVR32. However, I still took the time to
switch all the upstreamed board dts to the new bindings.
However, there is no other choice than breaking the mainly unused
pwm-atmel-tcb binding. Only the kizbox is actually using it.

I hope we could quickly come to an agreement on the new DT bindings and
include those changes in 4.8.

Regarding the tcbclksrc driver, I'm not completely happy with the
request_irq/free_irq thing but there is not much choice unless we want
to pass in the clksrc handler even when using the clkevt driver as they
may share the same interrupt.

Cc: Antoine Aubert <a.aubert@overkiz.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-pwm@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>

Alexandre Belloni (47):
  ARM: at91: Document new TCB bindings
  ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91rm9200ek; use TCB0 as clocksource
  ARM: dts: at91: mpa1600; use TCB0 as clocksource
  ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: ethernut5: use TCB0 as clocksource
  ARM: dts: at91: foxg20: use TCB0 as clocksource
  ARM: dts: at91: animeo_ip: use TCB0 as clocksource
  ARM: dts: at91: kizbox: use TCB0 as clocksource
  ARM: dts: at91: at91sam9g20ek: use TCB0 as clocksource
  ARM: dts: at91: ge863-pro3: use TCB0 as clocksource
  ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9261ek: use TCB0 as clocksource
  ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9263ek: use TCB0 as clocksource
  ARM: dts: at91: calao: use TCB0 as clocksource
  ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9m10g45ek: use TCB0 as clocksource
  ARM: dts: at91: pm9g45: use TCB0 as clocksource
  ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9rlek: use TCB0 as clocksource
  ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9n12ek: use TCB0 as clocksource
  ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: at91sam9x5cm: use TCB0 as clocksource
  ARM: dts: at91: acme/g25: use TCB0 as clocksource
  ARM: dts: at91: cosino: use TCB0 as clocksource
  ARM: dts: at91: kizboxmini: use TCB0 as clocksource
  ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: sama5d3xek; use TCB0 as clocksource
  ARM: dts: at91: sama5d3 Xplained: use TCB0 as clocksource
  ARM: dts: at91: kizbox2: use TCB0 as clocksource
  ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: sama5d4: Add TCB2
  ARM: dts: at91: sama5d4ek: use TCB2 as clocksource
  ARM: dts: at91: sama5d4 Xplained: use TCB2 as clocksource
  ARM: dts: at91: ma5d4: use TCB2 as clocksource
  ARM: dts: at91: vinco: use TCB2 as clocksource
  ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon
    devices
  ARM: dts: at91: sama5d2 Xplained: use TCB0 as clocksource
  clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  clocksource/drivers: Add a clockevent driver for Atmel TC blocks
  clocksource: atmel-pit: allow unselecting ATMEL_PIT
  ARM: at91/defconfig: sama5: unselect ATMEL_PIT
  ARM: at91/defconfig: at91_dt unselect ATMEL_PIT
  PWM: atmel-tcb: switch to new binding
  ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding

Cyrille Pitchen (1):
  clk: at91: replace usleep() by udelay() calls

 .../devicetree/bindings/arm/atmel-at91.txt         |  32 ---
 .../devicetree/bindings/mfd/atmel-tcb.txt          |  62 +++++
 .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      |  12 +-
 arch/arm/boot/dts/animeo_ip.dts                    |  12 +
 arch/arm/boot/dts/at91-ariag25.dts                 |  12 +
 arch/arm/boot/dts/at91-ariettag25.dts              |  12 +
 arch/arm/boot/dts/at91-cosino.dtsi                 |  12 +
 arch/arm/boot/dts/at91-foxg20.dts                  |  12 +
 arch/arm/boot/dts/at91-kizbox.dts                  |  54 +++-
 arch/arm/boot/dts/at91-kizbox2.dts                 |  12 +
 arch/arm/boot/dts/at91-kizboxmini.dts              |  12 +
 arch/arm/boot/dts/at91-qil_a9260.dts               |  12 +
 arch/arm/boot/dts/at91-sama5d2_xplained.dts        |  12 +
 arch/arm/boot/dts/at91-sama5d3_xplained.dts        |  12 +
 arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi          |  12 +
 arch/arm/boot/dts/at91-sama5d4_xplained.dts        |  12 +
 arch/arm/boot/dts/at91-sama5d4ek.dts               |  12 +
 arch/arm/boot/dts/at91-vinco.dts                   |  12 +
 arch/arm/boot/dts/at91rm9200.dtsi                  |   8 +-
 arch/arm/boot/dts/at91rm9200ek.dts                 |  12 +
 arch/arm/boot/dts/at91sam9260.dtsi                 |   8 +-
 arch/arm/boot/dts/at91sam9261.dtsi                 |   4 +-
 arch/arm/boot/dts/at91sam9261ek.dts                |  12 +
 arch/arm/boot/dts/at91sam9263.dtsi                 |   4 +-
 arch/arm/boot/dts/at91sam9263ek.dts                |  12 +
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi        |  12 +
 arch/arm/boot/dts/at91sam9g45.dtsi                 |   8 +-
 arch/arm/boot/dts/at91sam9m10g45ek.dts             |  12 +
 arch/arm/boot/dts/at91sam9n12.dtsi                 |   8 +-
 arch/arm/boot/dts/at91sam9n12ek.dts                |  12 +
 arch/arm/boot/dts/at91sam9rl.dtsi                  |   4 +-
 arch/arm/boot/dts/at91sam9rlek.dts                 |  12 +
 arch/arm/boot/dts/at91sam9x5.dtsi                  |   8 +-
 arch/arm/boot/dts/at91sam9x5cm.dtsi                |  12 +
 arch/arm/boot/dts/ethernut5.dts                    |  12 +
 arch/arm/boot/dts/ge863-pro3.dtsi                  |  12 +
 arch/arm/boot/dts/mpa1600.dts                      |  12 +
 arch/arm/boot/dts/pm9g45.dts                       |  12 +
 arch/arm/boot/dts/sama5d2.dtsi                     |   8 +-
 arch/arm/boot/dts/sama5d3.dtsi                     |   4 +-
 arch/arm/boot/dts/sama5d3_tcb1.dtsi                |   4 +-
 arch/arm/boot/dts/sama5d3xcm.dtsi                  |  12 +
 arch/arm/boot/dts/sama5d4.dtsi                     |  18 +-
 arch/arm/boot/dts/tny_a9260_common.dtsi            |  12 +
 arch/arm/boot/dts/tny_a9263.dts                    |  12 +
 arch/arm/boot/dts/usb_a9260_common.dtsi            |  12 +
 arch/arm/boot/dts/usb_a9263.dts                    |  12 +
 arch/arm/configs/at91_dt_defconfig                 |   1 +
 arch/arm/configs/sama5_defconfig                   |   1 +
 drivers/clk/at91/clk-main.c                        |   2 +-
 drivers/clk/at91/clk-slow.c                        |   6 +-
 drivers/clocksource/Kconfig                        |  32 ++-
 drivers/clocksource/Makefile                       |   4 +-
 drivers/clocksource/timer-atmel-tcbclkevt.c        | 220 +++++++++++++++
 drivers/clocksource/timer-atmel-tcbclksrc.c        | 305 +++++++++++++++++++++
 drivers/pwm/Kconfig                                |   3 +-
 drivers/pwm/pwm-atmel-tcb.c                        | 219 ++++++++-------
 include/soc/at91/atmel_tcb.h                       | 220 +++++++++++++++
 58 files changed, 1452 insertions(+), 179 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt
 create mode 100644 drivers/clocksource/timer-atmel-tcbclkevt.c
 create mode 100644 drivers/clocksource/timer-atmel-tcbclksrc.c
 create mode 100644 include/soc/at91/atmel_tcb.h

-- 
2.8.1

^ permalink raw reply	[flat|nested] 75+ messages in thread

* [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:30   ` Arnd Bergmann
  2016-06-11  7:49   ` Boris Brezillon
  2016-06-10 22:03 ` [PATCH 02/48] ARM: at91: Document new TCB bindings Alexandre Belloni
                   ` (46 subsequent siblings)
  47 siblings, 2 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Cyrille Pitchen, Stephen Boyd,
	linux-clk, Alexandre Belloni

From: Cyrille Pitchen <cyrille.pitchen@atmel.com>

Fix the main and slow clock .prepare() implementations which used to call
usleep() when the scheduler wasn't ready yet.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 drivers/clk/at91/clk-main.c | 2 +-
 drivers/clk/at91/clk-slow.c | 6 +++---
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/at91/clk-main.c b/drivers/clk/at91/clk-main.c
index 58b5baca670c..12c5062aeb92 100644
--- a/drivers/clk/at91/clk-main.c
+++ b/drivers/clk/at91/clk-main.c
@@ -342,7 +342,7 @@ static int clk_main_probe_frequency(struct regmap *regmap)
 		regmap_read(regmap, AT91_CKGR_MCFR, &mcfr);
 		if (mcfr & AT91_PMC_MAINRDY)
 			return 0;
-		usleep_range(MAINF_LOOP_MIN_WAIT, MAINF_LOOP_MAX_WAIT);
+		udelay(MAINF_LOOP_MIN_WAIT);
 	} while (time_before(prep_time, timeout));
 
 	return -ETIMEDOUT;
diff --git a/drivers/clk/at91/clk-slow.c b/drivers/clk/at91/clk-slow.c
index 61090b1146cf..612e893ce994 100644
--- a/drivers/clk/at91/clk-slow.c
+++ b/drivers/clk/at91/clk-slow.c
@@ -76,7 +76,7 @@ static int clk_slow_osc_prepare(struct clk_hw *hw)
 
 	writel(tmp | AT91_SCKC_OSC32EN, sckcr);
 
-	usleep_range(osc->startup_usec, osc->startup_usec + 1);
+	udelay(osc->startup_usec);
 
 	return 0;
 }
@@ -195,7 +195,7 @@ static int clk_slow_rc_osc_prepare(struct clk_hw *hw)
 
 	writel(readl(sckcr) | AT91_SCKC_RCEN, sckcr);
 
-	usleep_range(osc->startup_usec, osc->startup_usec + 1);
+	udelay(osc->startup_usec);
 
 	return 0;
 }
@@ -304,7 +304,7 @@ static int clk_sam9x5_slow_set_parent(struct clk_hw *hw, u8 index)
 
 	writel(tmp, sckcr);
 
-	usleep_range(SLOWCK_SW_TIME_USEC, SLOWCK_SW_TIME_USEC + 1);
+	udelay(SLOWCK_SW_TIME_USEC);
 
 	return 0;
 }
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 02/48] ARM: at91: Document new TCB bindings
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-14 21:47   ` Rob Herring
  2016-06-10 22:03 ` [PATCH 03/48] ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (45 subsequent siblings)
  47 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Daniel Lezcano, Thierry Reding, linux-pwm, Rob Herring,
	devicetree

The current binding for the TCB is not flexible enough for some use cases
and prevents proper utilization of all the channels.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 .../devicetree/bindings/arm/atmel-at91.txt         | 32 -----------
 .../devicetree/bindings/mfd/atmel-tcb.txt          | 62 ++++++++++++++++++++++
 .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      | 12 +++--
 3 files changed, 69 insertions(+), 37 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index e1f5ad855f14..3dc758403d03 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -60,38 +60,6 @@ System Timer (ST) required properties:
 Its subnodes can be:
 - watchdog: compatible should be "atmel,at91rm9200-wdt"
 
-TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-tcb".
-  <chip> can be "at91rm9200" or "at91sam9x5"
-- reg: Should contain registers location and length
-- interrupts: Should contain all interrupts for the TC block
-  Note that you can specify several interrupt cells if the TC
-  block has one interrupt per channel.
-- clock-names: tuple listing input clock names.
-	Required elements: "t0_clk", "slow_clk"
-	Optional elements: "t1_clk", "t2_clk"
-- clocks: phandles to input clocks.
-
-Examples:
-
-One interrupt per TC block:
-	tcb0: timer@fff7c000 {
-		compatible = "atmel,at91rm9200-tcb";
-		reg = <0xfff7c000 0x100>;
-		interrupts = <18 4>;
-		clocks = <&tcb0_clk>;
-		clock-names = "t0_clk";
-	};
-
-One interrupt per TC channel in a TC block:
-	tcb1: timer@fffdc000 {
-		compatible = "atmel,at91rm9200-tcb";
-		reg = <0xfffdc000 0x100>;
-		interrupts = <26 4 27 4 28 4>;
-		clocks = <&tcb1_clk>;
-		clock-names = "t0_clk";
-	};
-
 RSTC Reset Controller required properties:
 - compatible: Should be "atmel,<chip>-rstc".
   <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3"
diff --git a/Documentation/devicetree/bindings/mfd/atmel-tcb.txt b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
new file mode 100644
index 000000000000..48196752c78f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
@@ -0,0 +1,62 @@
+* Device tree bindings for Atmel Timer Counter Blocks
+- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon".
+  <chip> can be "at91rm9200" or "at91sam9x5"
+- reg: Should contain registers location and length
+- #address-cells: has to be 1
+- #size-cells: has to be 0
+- interrupts: Should contain all interrupts for the TC block
+  Note that you can specify several interrupt cells if the TC
+  block has one interrupt per channel.
+- clock-names: tuple listing input clock names.
+	Required elements: "t0_clk", "slow_clk"
+	Optional elements: "t1_clk", "t2_clk"
+- clocks: phandles to input clocks.
+
+The TCB can expose multiple subdevices:
+ * a clocksource and clockevent device
+   - compatible: Should be "atmel,tcb-clksrc"
+   - reg: Should contain the TCB channels to be used. If the
+     counter width is 16 bits (at91rm9200-tcb), two consecutive
+     channels are needed. Else, only one channel will be used.
+
+ * a clockevent device
+   - compatible: Should be "atmel,tcb-clkevt"
+   - reg: Should contain the TCB channel to be used
+
+ * a PWM chip: see ../pwm/atmel-tcb-pwm.txt
+
+Examples:
+
+One interrupt per TC block:
+	tcb0: timer@fff7c000 {
+		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfff7c000 0x100>;
+		interrupts = <18 4>;
+		clocks = <&tcb0_clk>;
+		clock-names = "t0_clk";
+
+		timer@0 {
+			compatible = "atmel,tcb-clksrc";
+			reg = <0>, <1>;
+		};
+
+		timer@2 {
+			compatible = "atmel,tcb-clkevt";
+			reg = <2>;
+		};
+	};
+
+One interrupt per TC channel in a TC block:
+	tcb1: timer@fffdc000 {
+		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfffdc000 0x100>;
+		interrupts = <26 4>, <27 4>, <28 4>;
+		clocks = <&tcb1_clk>;
+		clock-names = "t0_clk";
+	};
+
+
diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
index 8031148bcf85..ab8fbd5ba184 100644
--- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
@@ -2,15 +2,17 @@ Atmel TCB PWM controller
 
 Required properties:
 - compatible: should be "atmel,tcb-pwm"
+- reg: tcb channel to use. Each channel can export 2 PWMs
 - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
   the cells format. The only third cell flag supported by this binding is
   PWM_POLARITY_INVERTED.
-- tc-block: The Timer Counter block to use as a PWM chip.
 
 Example:
 
-pwm {
-	compatible = "atmel,tcb-pwm";
-	#pwm-cells = <3>;
-	tc-block = <1>;
+tcb0: timer@f800c000 {
+	pwm@0 {
+		compatible = "atmel,tcb-pwm";
+		reg = <0>;
+		#pwm-cells = <3>;
+	};
 };
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 03/48] ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 02/48] ARM: at91: Document new TCB bindings Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 04/48] ARM: dts: at91: at91rm9200ek; use TCB0 as clocksource Alexandre Belloni
                   ` (44 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use
regmap instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91rm9200.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index f6cb7a80a2f5..ec0a7d36ee43 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -375,7 +375,9 @@
 			};
 
 			tcb0: timer@fffa0000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
 					      18 IRQ_TYPE_LEVEL_HIGH 0
@@ -385,7 +387,9 @@
 			};
 
 			tcb1: timer@fffa4000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffa4000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0
 					      21 IRQ_TYPE_LEVEL_HIGH 0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 04/48] ARM: dts: at91: at91rm9200ek; use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (2 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 03/48] ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 05/48] ARM: dts: at91: mpa1600; " Alexandre Belloni
                   ` (43 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91rm9200ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
index f90e1c2d3caa..051cc8b88513 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/at91rm9200ek.dts
@@ -32,6 +32,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usb1: gadget@fffb0000 {
 				atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>;
 				atmel,pullup-gpio = <&pioD 5 GPIO_ACTIVE_HIGH>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 05/48] ARM: dts: at91: mpa1600; use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (3 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 04/48] ARM: dts: at91: at91rm9200ek; use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 06/48] ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (42 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Joachim Eastwood

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/mpa1600.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/mpa1600.dts b/arch/arm/boot/dts/mpa1600.dts
index f0f5e1098928..d1c3ec1db086 100644
--- a/arch/arm/boot/dts/mpa1600.dts
+++ b/arch/arm/boot/dts/mpa1600.dts
@@ -41,6 +41,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			macb0: ethernet@fffbc000 {
 				phy-mode = "rmii";
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 06/48] ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (4 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 05/48] ARM: dts: at91: mpa1600; " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 07/48] ARM: dts: at91: ethernut5: use TCB0 as clocksource Alexandre Belloni
                   ` (41 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use
regmap instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9260.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index d4884dd1c243..7b2aa604a924 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -376,7 +376,9 @@
 			};
 
 			tcb0: timer@fffa0000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
 					      18 IRQ_TYPE_LEVEL_HIGH 0
@@ -386,7 +388,9 @@
 			};
 
 			tcb1: timer@fffdc000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffdc000 0x100>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0
 					      27 IRQ_TYPE_LEVEL_HIGH 0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 07/48] ARM: dts: at91: ethernut5: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (5 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 06/48] ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 08/48] ARM: dts: at91: foxg20: " Alexandre Belloni
                   ` (40 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Martin Reimann, Tim Schendekehl

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/ethernut5.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/ethernut5.dts
index 243044343ee8..26ce9ee46c05 100644
--- a/arch/arm/boot/dts/ethernut5.dts
+++ b/arch/arm/boot/dts/ethernut5.dts
@@ -36,6 +36,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usart0: serial@fffb0000 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 08/48] ARM: dts: at91: foxg20: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (6 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 07/48] ARM: dts: at91: ethernut5: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 09/48] ARM: dts: at91: animeo_ip: " Alexandre Belloni
                   ` (39 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Sergio Tanzilli, Douglas Gilbert

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-foxg20.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/at91-foxg20.dts
index 6bf873e7d96c..cee2296b2c17 100644
--- a/arch/arm/boot/dts/at91-foxg20.dts
+++ b/arch/arm/boot/dts/at91-foxg20.dts
@@ -43,6 +43,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usb1: gadget@fffa4000 {
 				atmel,vbus-gpio = <&pioC 6 GPIO_ACTIVE_HIGH>;
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 09/48] ARM: dts: at91: animeo_ip: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (7 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 08/48] ARM: dts: at91: foxg20: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 10/48] ARM: dts: at91: kizbox: " Alexandre Belloni
                   ` (38 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/animeo_ip.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts
index 0962f2fa3f6e..e55190d706a9 100644
--- a/arch/arm/boot/dts/animeo_ip.dts
+++ b/arch/arm/boot/dts/animeo_ip.dts
@@ -52,6 +52,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usart0: serial@fffb0000 {
 				pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>;
 				linux,rs485-enabled-at-boot-time;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 10/48] ARM: dts: at91: kizbox: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (8 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 09/48] ARM: dts: at91: animeo_ip: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 11/48] ARM: dts: at91: at91sam9g20ek: " Alexandre Belloni
                   ` (37 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Antoine Aubert

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Antoine Aubert <a.aubert@overkiz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-kizbox.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 229e989eb60d..58c5d0d3dd66 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -31,6 +31,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			macb0: ethernet@fffc4000 {
 				phy-mode = "mii";
 				pinctrl-0 = <&pinctrl_macb_rmii
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 11/48] ARM: dts: at91: at91sam9g20ek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (9 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 10/48] ARM: dts: at91: kizbox: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 12/48] ARM: dts: at91: ge863-pro3: " Alexandre Belloni
                   ` (36 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index e9cc99b6353a..e13018b4df01 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -51,6 +51,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usart0: serial@fffb0000 {
 				pinctrl-0 =
 					<&pinctrl_usart0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 12/48] ARM: dts: at91: ge863-pro3: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (10 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 11/48] ARM: dts: at91: at91sam9g20ek: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 13/48] ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (35 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Fabio Porcedda

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/ge863-pro3.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/ge863-pro3.dtsi b/arch/arm/boot/dts/ge863-pro3.dtsi
index 0d0e62489d93..6b5eb285b072 100644
--- a/arch/arm/boot/dts/ge863-pro3.dtsi
+++ b/arch/arm/boot/dts/ge863-pro3.dtsi
@@ -27,6 +27,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			dbgu: serial@fffff200 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 13/48] ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (11 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 12/48] ARM: dts: at91: ge863-pro3: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 14/48] ARM: dts: at91: at91sam9261ek: use TCB0 as clocksource Alexandre Belloni
                   ` (34 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9261.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index 5e09de4eb9cd..7dd2441561c1 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -114,7 +114,9 @@
 			ranges;
 
 			tcb0: timer@fffa0000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>,
 					     <18 IRQ_TYPE_LEVEL_HIGH 0>,
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 14/48] ARM: dts: at91: at91sam9261ek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (12 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 13/48] ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 15/48] ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (33 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in sama5_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9261ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts
index 55bd51f07fa6..d1b1d11fb974 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/at91sam9261ek.dts
@@ -106,6 +106,18 @@
 		};
 
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			usb1: gadget@fffa4000 {
 				atmel,vbus-gpio = <&pioB 29 GPIO_ACTIVE_HIGH>;
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 15/48] ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (13 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 14/48] ARM: dts: at91: at91sam9261ek: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 16/48] ARM: dts: at91: at91sam9263ek: use TCB0 as clocksource Alexandre Belloni
                   ` (32 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9263.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 93446420af25..a06c8882c065 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -374,7 +374,9 @@
 			};
 
 			tcb0: timer@fff7c000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfff7c000 0x100>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb_clk>, <&slow_xtal>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 16/48] ARM: dts: at91: at91sam9263ek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (14 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 15/48] ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 17/48] ARM: dts: at91: calao: " Alexandre Belloni
                   ` (31 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9263ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 59df9d73d276..e3b51e8d01bb 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -37,6 +37,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fff7c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usart0: serial@fff8c000 {
 				pinctrl-0 = <
 					&pinctrl_usart0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 17/48] ARM: dts: at91: calao: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (15 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 16/48] ARM: dts: at91: at91sam9263ek: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 18/48] ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (30 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Gregory Hermant

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
[tested on usb_a9g20 and usb_a9263]
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-qil_a9260.dts    | 12 ++++++++++++
 arch/arm/boot/dts/tny_a9260_common.dtsi | 12 ++++++++++++
 arch/arm/boot/dts/tny_a9263.dts         | 12 ++++++++++++
 arch/arm/boot/dts/usb_a9260_common.dtsi | 12 ++++++++++++
 arch/arm/boot/dts/usb_a9263.dts         | 12 ++++++++++++
 5 files changed, 60 insertions(+)

diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/at91-qil_a9260.dts
index 4f2eebf4a560..bbc1f667cc65 100644
--- a/arch/arm/boot/dts/at91-qil_a9260.dts
+++ b/arch/arm/boot/dts/at91-qil_a9260.dts
@@ -40,6 +40,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usb1: gadget@fffa4000 {
 				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
diff --git a/arch/arm/boot/dts/tny_a9260_common.dtsi b/arch/arm/boot/dts/tny_a9260_common.dtsi
index ce7138c3af1b..0b2902d7ccd3 100644
--- a/arch/arm/boot/dts/tny_a9260_common.dtsi
+++ b/arch/arm/boot/dts/tny_a9260_common.dtsi
@@ -36,6 +36,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			dbgu: serial@fffff200 {
 				status = "okay";
 			};
diff --git a/arch/arm/boot/dts/tny_a9263.dts b/arch/arm/boot/dts/tny_a9263.dts
index 3043296345b7..32ee65a9f99f 100644
--- a/arch/arm/boot/dts/tny_a9263.dts
+++ b/arch/arm/boot/dts/tny_a9263.dts
@@ -45,6 +45,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fff7c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usb1: gadget@fff78000 {
 				atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>;
 				status = "okay";
diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/usb_a9260_common.dtsi
index 9beea8976584..369a26bc5edc 100644
--- a/arch/arm/boot/dts/usb_a9260_common.dtsi
+++ b/arch/arm/boot/dts/usb_a9260_common.dtsi
@@ -32,6 +32,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			macb0: ethernet@fffc4000 {
 				phy-mode = "rmii";
 				status = "okay";
diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/usb_a9263.dts
index 8cc6edb29694..49a25c26b8e4 100644
--- a/arch/arm/boot/dts/usb_a9263.dts
+++ b/arch/arm/boot/dts/usb_a9263.dts
@@ -45,6 +45,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fff7c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			macb0: ethernet@fffbc000 {
 				phy-mode = "rmii";
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 18/48] ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (16 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 17/48] ARM: dts: at91: calao: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 19/48] ARM: dts: at91: at91sam9m10g45ek: use TCB0 as clocksource Alexandre Belloni
                   ` (29 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9g45.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 8837b7e4292c..2b95aef4da44 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -405,7 +405,9 @@
 			};
 
 			tcb0: timer@fff7c000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfff7c000 0x100>;
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>, <&clk32k>;
@@ -413,7 +415,9 @@
 			};
 
 			tcb1: timer@fffd4000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffd4000 0x100>;
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&tcb0_clk>, <&tcb0_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 19/48] ARM: dts: at91: at91sam9m10g45ek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (17 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 18/48] ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 20/48] ARM: dts: at91: pm9g45: " Alexandre Belloni
                   ` (28 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9m10g45ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 2400c99134f7..132064c60863 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -39,6 +39,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@fff7c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			usart1: serial@fff90000 {
 				pinctrl-0 =
 					<&pinctrl_usart1
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 20/48] ARM: dts: at91: pm9g45: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (18 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 19/48] ARM: dts: at91: at91sam9m10g45ek: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 21/48] ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (27 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/pm9g45.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
index 66afcff67fde..5d5ccefa8644 100644
--- a/arch/arm/boot/dts/pm9g45.dts
+++ b/arch/arm/boot/dts/pm9g45.dts
@@ -63,6 +63,18 @@
 				};
 			};
 
+			tcb0: timer@fff7c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			mmc0: mmc@fff80000 {
 				pinctrl-0 = <
 					&pinctrl_board_mmc
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 21/48] ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (19 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 20/48] ARM: dts: at91: pm9g45: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 22/48] ARM: dts: at91: at91sam9rlek: use TCB0 as clocksource Alexandre Belloni
                   ` (26 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rl.dtsi | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 6d829db4e887..da74b769d5ac 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -116,7 +116,9 @@
 			ranges;
 
 			tcb0: timer@fffa0000 {
-				compatible = "atmel,at91rm9200-tcb";
+				compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 0>,
 					     <17 IRQ_TYPE_LEVEL_HIGH 0>,
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 22/48] ARM: dts: at91: at91sam9rlek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (20 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 21/48] ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 23/48] ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (25 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9rlek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index f10566f759cd..cc0b6b19c5bf 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -101,6 +101,18 @@
 		};
 
 		apb {
+			tcb0: timer@fffa0000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>, <1>;
+				};
+
+				timer@2 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <2>;
+				};
+			};
+
 			mmc0: mmc@fffa4000 {
 				pinctrl-0 = <
 					&pinctrl_board_mmc0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 23/48] ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (21 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 22/48] ARM: dts: at91: at91sam9rlek: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 24/48] ARM: dts: at91: at91sam9n12ek: use TCB0 as clocksource Alexandre Belloni
                   ` (24 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9n12.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 95569a87b6c9..1f26cb66238e 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -430,7 +430,9 @@
 			};
 
 			tcb0: timer@f8008000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf8008000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb_clk>, <&clk32k>;
@@ -438,7 +440,9 @@
 			};
 
 			tcb1: timer@f800c000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf800c000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 24/48] ARM: dts: at91: at91sam9n12ek: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (22 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 23/48] ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 25/48] ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (23 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9n12ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 626c67d66626..3491db62d6b3 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -42,6 +42,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			i2c0: i2c@f8010000 {
 				status = "okay";
 
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 25/48] ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (23 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 24/48] ARM: dts: at91: at91sam9n12ek: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 26/48] ARM: dts: at91: at91sam9x5cm: use TCB0 as clocksource Alexandre Belloni
                   ` (22 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use regmap
instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9x5.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index cd0cd5fd09a3..6d845993406f 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -417,7 +417,9 @@
 			};
 
 			tcb0: timer@f8008000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf8008000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&clk32k>;
@@ -425,7 +427,9 @@
 			};
 
 			tcb1: timer@f800c000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf800c000 0x100>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 26/48] ARM: dts: at91: at91sam9x5cm: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (24 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 25/48] ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 27/48] ARM: dts: at91: acme/g25: " Alexandre Belloni
                   ` (21 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

[tested on at91sam9x25ek and at91sam9x35ek]
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91sam9x5cm.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/at91sam9x5cm.dtsi
index b098ad8cd93a..40676cc9b172 100644
--- a/arch/arm/boot/dts/at91sam9x5cm.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5cm.dtsi
@@ -24,6 +24,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			pinctrl@fffff400 {
 				1wire_cm {
 					pinctrl_1wire_cm: 1wire_cm-0 {
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 27/48] ARM: dts: at91: acme/g25: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (25 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 26/48] ARM: dts: at91: at91sam9x5cm: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 28/48] ARM: dts: at91: cosino: " Alexandre Belloni
                   ` (20 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Sergio Tanzilli, Douglas Gilbert

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Sergio Tanzilli <tanzilli@acmesystems.it>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-ariag25.dts    | 12 ++++++++++++
 arch/arm/boot/dts/at91-ariettag25.dts | 12 ++++++++++++
 2 files changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/at91-ariag25.dts b/arch/arm/boot/dts/at91-ariag25.dts
index e9ced30159a7..b00aa7607283 100644
--- a/arch/arm/boot/dts/at91-ariag25.dts
+++ b/arch/arm/boot/dts/at91-ariag25.dts
@@ -67,6 +67,18 @@
 				};
 			};
 
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			i2c0: i2c@f8010000 {
 				status = "okay";
 			};
diff --git a/arch/arm/boot/dts/at91-ariettag25.dts b/arch/arm/boot/dts/at91-ariettag25.dts
index c514502081d2..58e0026157f7 100644
--- a/arch/arm/boot/dts/at91-ariettag25.dts
+++ b/arch/arm/boot/dts/at91-ariettag25.dts
@@ -45,6 +45,18 @@
 				};
 			};
 
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			usb2: gadget@f803c000 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 28/48] ARM: dts: at91: cosino: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (26 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 27/48] ARM: dts: at91: acme/g25: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 29/48] ARM: dts: at91: kizboxmini: " Alexandre Belloni
                   ` (19 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Rodolfo Giometti

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-cosino.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-cosino.dtsi b/arch/arm/boot/dts/at91-cosino.dtsi
index b6ea3f4a7206..0cbab6f588b7 100644
--- a/arch/arm/boot/dts/at91-cosino.dtsi
+++ b/arch/arm/boot/dts/at91-cosino.dtsi
@@ -46,6 +46,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			mmc0: mmc@f0008000 {
 				pinctrl-0 = <
 					&pinctrl_board_mmc0
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 29/48] ARM: dts: at91: kizboxmini: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (27 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 28/48] ARM: dts: at91: cosino: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 30/48] ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (18 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Antoine Aubert

Use tcb0 as the clocksource like previously selected in at91_dt_defconfig.

Cc: Antoine Aubert <a.aubert@overkiz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-kizboxmini.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini.dts
index 9682d105d4d8..2fc100414a00 100644
--- a/arch/arm/boot/dts/at91-kizboxmini.dts
+++ b/arch/arm/boot/dts/at91-kizboxmini.dts
@@ -34,6 +34,18 @@
 
 	ahb {
 		apb {
+			tcb0: timer@f8008000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			usart0: serial@f801c000 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 30/48] ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (28 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 29/48] ARM: dts: at91: kizboxmini: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 31/48] ARM: dts: at91: sama5d3xek; use TCB0 as clocksource Alexandre Belloni
                   ` (17 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use
regmap instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3.dtsi      | 4 +++-
 arch/arm/boot/dts/sama5d3_tcb1.dtsi | 4 +++-
 2 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 36301bd9a14a..cfa659a18639 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -142,7 +142,9 @@
 			};
 
 			tcb0: timer@f0010000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf0010000 0x100>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&clk32k>;
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
index 801f9745e82f..cb30bdb1a9ca 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi
@@ -28,7 +28,9 @@
 			};
 
 			tcb1: timer@f8014000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf8014000 0x100>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb1_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 31/48] ARM: dts: at91: sama5d3xek; use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (29 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 30/48] ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 32/48] ARM: dts: at91: sama5d3 Xplained: " Alexandre Belloni
                   ` (16 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in sama5_defconfig.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d3xcm.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
index 2cf9c3611db6..90d36b755858 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
@@ -35,6 +35,18 @@
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
 			};
 
+			tcb0: timer@f0010000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			macb0: ethernet@f0028000 {
 				phy-mode = "rgmii";
 				#address-cells = <1>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 32/48] ARM: dts: at91: sama5d3 Xplained: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (30 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 31/48] ARM: dts: at91: sama5d3xek; use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 33/48] ARM: dts: at91: kizbox2: " Alexandre Belloni
                   ` (15 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in sama5_defconfig.

Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d3_xplained.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index f3e2b96c06a3..9e9bf3caabd6 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -65,6 +65,18 @@
 				status = "okay";
 			};
 
+			tcb0: timer@f0010000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			i2c0: i2c@f0014000 {
 				pinctrl-0 = <&pinctrl_i2c0_pu>;
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 33/48] ARM: dts: at91: kizbox2: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (31 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 32/48] ARM: dts: at91: sama5d3 Xplained: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 34/48] ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (14 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Antoine Aubert

Use tcb0 as the clocksource like previously selected in sama5_defconfig.

Cc: Antoine Aubert <a.aubert@overkiz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-kizbox2.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
index 50a14568f094..03c47eab3771 100644
--- a/arch/arm/boot/dts/at91-kizbox2.dts
+++ b/arch/arm/boot/dts/at91-kizbox2.dts
@@ -94,6 +94,18 @@
 				};
 			};
 
+			tcb0: timer@f0010000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			usart0: serial@f001c000 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 34/48] ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (32 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 33/48] ARM: dts: at91: kizbox2: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 35/48] ARM: dts: at91: sama5d4: Add TCB2 Alexandre Belloni
                   ` (13 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allow sto reuse
regmap instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d4.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index 4e2cc30d6615..9fd39a0d2251 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -954,7 +954,9 @@
 			};
 
 			tcb0: timer@f801c000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf801c000 0x100>;
 				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&clk32k>;
@@ -1182,7 +1184,9 @@
 			};
 
 			tcb1: timer@fc020000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xfc020000 0x100>;
 				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb1_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 35/48] ARM: dts: at91: sama5d4: Add TCB2
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (33 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 34/48] ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 36/48] ARM: dts: at91: sama5d4ek: use TCB2 as clocksource Alexandre Belloni
                   ` (12 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

The third TC block is missing from the dtsi. It has no output pins but can
still be used as a clocksource/clockevents device as the IRQ is wired.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d4.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index 9fd39a0d2251..ef7b9b08546d 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -1193,6 +1193,16 @@
 				clock-names = "t0_clk", "slow_clk";
 			};
 
+			tcb2: timer@fc024000 {
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0xfc024000 0x100>;
+				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&tcb2_clk>, <&clk32k>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
 			macb1: ethernet@fc028000 {
 				compatible = "atmel,sama5d4-gem";
 				reg = <0xfc028000 0x100>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 36/48] ARM: dts: at91: sama5d4ek: use TCB2 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (34 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 35/48] ARM: dts: at91: sama5d4: Add TCB2 Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 37/48] ARM: dts: at91: sama5d4 Xplained: " Alexandre Belloni
                   ` (11 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

As TCB2 doesn't have any output pins, use it as a clocksource.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4ek.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index 4e98cda97403..5ccd2fb54e2a 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -194,6 +194,18 @@
 				status = "okay";
 			};
 
+			tcb2: timer@fc024000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			watchdog@fc068640 {
 				status = "okay";
 			};
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 37/48] ARM: dts: at91: sama5d4 Xplained: use TCB2 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (35 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 36/48] ARM: dts: at91: sama5d4ek: use TCB2 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 38/48] ARM: dts: at91: ma5d4: " Alexandre Belloni
                   ` (10 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

As TCB2 doesn't have any output pins, use it as a clocksource.

Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4_xplained.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index da84e65b56ef..c0be79d5cf50 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -122,6 +122,18 @@
 				status = "okay";
 			};
 
+			tcb2: timer@fc024000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			adc0: adc@fc034000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 38/48] ARM: dts: at91: ma5d4: use TCB2 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (36 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 37/48] ARM: dts: at91: sama5d4 Xplained: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 39/48] ARM: dts: at91: vinco: " Alexandre Belloni
                   ` (9 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni, Marek Vasut

As TCB2 doesn't have any output pins, use it as a clocksource.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
index e7b2109fc85a..d4ca06c2a8ce 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
@@ -86,6 +86,18 @@
 				};
 			};
 
+			tcb2: timer@fc024000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			adc0: adc@fc034000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 39/48] ARM: dts: at91: vinco: use TCB2 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (37 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 38/48] ARM: dts: at91: ma5d4: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 40/48] ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
                   ` (8 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Gregory CLEMENT

As TCB2 doesn't have any output pins, use it as a clocksource.

Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-vinco.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-vinco.dts b/arch/arm/boot/dts/at91-vinco.dts
index 6a366ee952a8..bb68042d3f95 100644
--- a/arch/arm/boot/dts/at91-vinco.dts
+++ b/arch/arm/boot/dts/at91-vinco.dts
@@ -151,6 +151,18 @@
 				status = "okay";
 			};
 
+			tcb2: timer@fc024000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			macb1: ethernet@fc028000 {
 				phy-mode = "rmii";
 				status = "okay";
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 40/48] ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (38 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 39/48] ARM: dts: at91: vinco: " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 41/48] ARM: dts: at91: sama5d2 Xplained: use TCB0 as clocksource Alexandre Belloni
                   ` (7 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time. It also allows to use
regmap instead of tclib.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/sama5d2.dtsi | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 2827e7ab5ebc..0db2f8b77227 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -906,7 +906,9 @@
 			};
 
 			tcb0: timer@f800c000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf800c000 0x100>;
 				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb0_clk>, <&clk32k>;
@@ -914,7 +916,9 @@
 			};
 
 			tcb1: timer@f8010000 {
-				compatible = "atmel,at91sam9x5-tcb";
+				compatible = "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0xf8010000 0x100>;
 				interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&tcb1_clk>, <&clk32k>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 41/48] ARM: dts: at91: sama5d2 Xplained: use TCB0 as clocksource
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (39 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 40/48] ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks Alexandre Belloni
                   ` (6 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

Use tcb0 as the clocksource like previously selected in sama5_defconfig.

Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-sama5d2_xplained.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index eb4f1ac96271..566d303e419b 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -135,6 +135,18 @@
 				};
 			};
 
+			tcb0: timer@f800c000 {
+				timer@0 {
+					compatible = "atmel,tcb-clksrc";
+					reg = <0>;
+				};
+
+				timer@1 {
+					compatible = "atmel,tcb-clkevt";
+					reg = <1>;
+				};
+			};
+
 			pdmic@f8018000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_pdmic_default>;
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (40 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 41/48] ARM: dts: at91: sama5d2 Xplained: use TCB0 as clocksource Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-11 12:48   ` Boris Brezillon
  2016-06-24 10:07   ` Daniel Lezcano
  2016-06-10 22:03 ` [PATCH 43/48] clocksource/drivers: Add a clockevent driver for Atmel " Alexandre Belloni
                   ` (5 subsequent siblings)
  47 siblings, 2 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Daniel Lezcano, Thomas Gleixner

Add a driver for the Atmel Timer Counter Blocks. This driver provides a
clocksource and a clockevent device. The clockevent device is linked to the
clocksource counter and so it will run at the same frequency.

This driver uses regmap and syscon to be able to probe early in the boot
and avoid having to switch on the TCB clocksource later. Using regmap also
means that unused TCB channels may be used by other drivers (PWM for
example).

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 drivers/clocksource/Kconfig                 |  13 ++
 drivers/clocksource/Makefile                |   3 +-
 drivers/clocksource/timer-atmel-tcbclksrc.c | 305 ++++++++++++++++++++++++++++
 include/soc/at91/atmel_tcb.h                | 220 ++++++++++++++++++++
 4 files changed, 540 insertions(+), 1 deletion(-)
 create mode 100644 drivers/clocksource/timer-atmel-tcbclksrc.c
 create mode 100644 include/soc/at91/atmel_tcb.h

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 47352d25c15e..ff7f4022c749 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -258,6 +258,19 @@ config ATMEL_ST
 	select CLKSRC_OF
 	select MFD_SYSCON
 
+config ATMEL_ARM_TCB_CLKSRC
+	bool "TC Block Clocksource"
+	select REGMAP_MMIO
+	depends on GENERIC_CLOCKEVENTS
+	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
+	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
+	help
+	  Select this to get a high precision clocksource based on a
+	  TC block with a 5+ MHz base clock rate.
+	  On platforms with 16-bit counters, two timer channels are combined
+	  to make a single 32-bit timer.
+	  It can also be used as a clock event device supporting oneshot mode.
+
 config CLKSRC_METAG_GENERIC
 	def_bool y if METAG
 	help
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 473974f9590a..988f33de5808 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -1,7 +1,8 @@
 obj-$(CONFIG_CLKSRC_PROBE)	+= clksrc-probe.o
 obj-$(CONFIG_ATMEL_PIT)		+= timer-atmel-pit.o
 obj-$(CONFIG_ATMEL_ST)		+= timer-atmel-st.o
-obj-$(CONFIG_ATMEL_TCB_CLKSRC)	+= tcb_clksrc.o
+obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
+obj-$(CONFIG_ATMEL_ARM_TCB_CLKSRC)	+= timer-atmel-tcbclksrc.o
 obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
 obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o
 obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC)	+= cs5535-clockevt.o
diff --git a/drivers/clocksource/timer-atmel-tcbclksrc.c b/drivers/clocksource/timer-atmel-tcbclksrc.c
new file mode 100644
index 000000000000..af0b1aab7a98
--- /dev/null
+++ b/drivers/clocksource/timer-atmel-tcbclksrc.c
@@ -0,0 +1,305 @@
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+#include <linux/sched_clock.h>
+#include <soc/at91/atmel_tcb.h>
+
+struct atmel_tcb_clksrc {
+	struct clocksource clksrc;
+	struct clock_event_device clkevt;
+	struct regmap *regmap;
+	struct clk *clk[2];
+	int channels[2];
+	u8 bits;
+	unsigned int irq;
+	bool registered;
+	bool irq_requested;
+};
+
+static struct atmel_tcb_clksrc tc = {
+	.clksrc = {
+		.name		= "tcb_clksrc",
+		.rating		= 200,
+		.mask		= CLOCKSOURCE_MASK(32),
+		.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+	},
+	.clkevt	= {
+		.name			= "tcb_clkevt",
+		.features		= CLOCK_EVT_FEAT_ONESHOT,
+		/* Should be lower than at91rm9200's system timer */
+		.rating			= 125,
+	},
+};
+
+static cycle_t tc_get_cycles(struct clocksource *cs)
+{
+	unsigned long	flags;
+	u32		lower, upper, tmp;
+
+	raw_local_irq_save(flags);
+	do {
+		regmap_read(tc.regmap, ATMEL_TC_CV(1), &upper);
+		regmap_read(tc.regmap, ATMEL_TC_CV(0), &lower);
+		regmap_read(tc.regmap, ATMEL_TC_CV(1), &tmp);
+	} while (upper != tmp);
+
+	raw_local_irq_restore(flags);
+	return (upper << 16) | lower;
+}
+
+static cycle_t tc_get_cycles32(struct clocksource *cs)
+{
+	u32 val;
+
+	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
+
+	return val;
+}
+
+static u64 tc_sched_clock_read(void)
+{
+	return tc_get_cycles(&tc.clksrc);
+}
+
+static u64 tc_sched_clock_read32(void)
+{
+	return tc_get_cycles32(&tc.clksrc);
+}
+
+static int tcb_clkevt_next_event(unsigned long delta,
+				 struct clock_event_device *d)
+{
+	u32 val;
+
+	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
+	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), val + delta);
+	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]), ATMEL_TC_CPCS);
+
+	return 0;
+}
+
+static irqreturn_t tc_clkevt_irq(int irq, void *handle)
+{
+	unsigned int sr;
+
+	regmap_read(tc.regmap, ATMEL_TC_SR(tc.channels[0]), &sr);
+	if (sr & ATMEL_TC_CPCS) {
+		tc.clkevt.event_handler(&tc.clkevt);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int tcb_clkevt_oneshot(struct clock_event_device *dev)
+{
+	int ret;
+
+	if (tc.irq_requested)
+		return 0;
+
+	ret = request_irq(tc.irq, tc_clkevt_irq, IRQF_TIMER | IRQF_SHARED,
+			  "tcb_clkevt", &tc);
+	if (!ret)
+		tc.irq_requested = true;
+
+	return ret;
+}
+
+static int tcb_clkevt_shutdown(struct clock_event_device *dev)
+{
+	regmap_write(tc.regmap, ATMEL_TC_IDR(tc.channels[0]), 0xff);
+	if (tc.bits == 16)
+		regmap_write(tc.regmap, ATMEL_TC_IDR(tc.channels[1]), 0xff);
+
+	if (tc.irq_requested) {
+		free_irq(tc.irq, &tc);
+		tc.irq_requested = false;
+	}
+
+	return 0;
+}
+
+static void __init tcb_setup_dual_chan(struct atmel_tcb_clksrc *tc,
+				       int mck_divisor_idx)
+{
+	/* first channel: waveform mode, input mclk/8, clock TIOA on overflow */
+	regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[0]),
+		     mck_divisor_idx	/* likely divide-by-8 */
+			| ATMEL_TC_CMR_WAVE
+			| ATMEL_TC_CMR_WAVESEL_UP	/* free-run */
+			| ATMEL_TC_CMR_ACPA(SET)	/* TIOA rises at 0 */
+			| ATMEL_TC_CMR_ACPC(CLEAR));	/* (duty cycle 50%) */
+	regmap_write(tc->regmap, ATMEL_TC_RA(tc->channels[0]), 0x0000);
+	regmap_write(tc->regmap, ATMEL_TC_RC(tc->channels[0]), 0x8000);
+	regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[0]), 0xff);	/* no irqs */
+	regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[0]),
+		     ATMEL_TC_CCR_CLKEN);
+
+	/* second channel: waveform mode, input TIOA */
+	regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[1]),
+		     ATMEL_TC_CMR_XC(tc->channels[1])	/* input: TIOA */
+		     | ATMEL_TC_CMR_WAVE
+		     | ATMEL_TC_CMR_WAVESEL_UP);	/* free-run */
+	regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[1]), 0xff);	/* no irqs */
+	regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[1]),
+		     ATMEL_TC_CCR_CLKEN);
+
+	/* chain both channel, we assume the previous channel */
+	regmap_write(tc->regmap, ATMEL_TC_BMR,
+		     ATMEL_TC_BMR_TCXC(1 + tc->channels[1], tc->channels[1]));
+	/* then reset all the timers */
+	regmap_write(tc->regmap, ATMEL_TC_BCR, ATMEL_TC_BCR_SYNC);
+}
+
+static void __init tcb_setup_single_chan(struct atmel_tcb_clksrc *tc,
+					 int mck_divisor_idx)
+{
+	/* channel 0:  waveform mode, input mclk/8 */
+	regmap_write(tc->regmap, ATMEL_TC_CMR(tc->channels[0]),
+		     mck_divisor_idx	/* likely divide-by-8 */
+			| ATMEL_TC_CMR_WAVE
+			| ATMEL_TC_CMR_WAVESEL_UP	/* free-run */
+			);
+	regmap_write(tc->regmap, ATMEL_TC_IDR(tc->channels[0]), 0xff);	/* no irqs */
+	regmap_write(tc->regmap, ATMEL_TC_CCR(tc->channels[0]),
+		     ATMEL_TC_CCR_CLKEN);
+
+	/* then reset all the timers */
+	regmap_write(tc->regmap, ATMEL_TC_BCR, ATMEL_TC_BCR_SYNC);
+}
+
+static void __init tcb_clksrc_init(struct device_node *node)
+{
+	const struct of_device_id *match;
+	u32 rate, divided_rate = 0;
+	int best_divisor_idx = -1;
+	int i, err;
+
+	if (tc.registered)
+		return;
+
+	tc.regmap = syscon_node_to_regmap(node->parent);
+	if (IS_ERR(tc.regmap))
+		return;
+
+	match = of_match_node(atmel_tcb_dt_ids, node->parent);
+	tc.bits = (int)match->data;
+
+	err = of_property_read_u32_index(node, "reg", 0, &tc.channels[0]);
+	if (err)
+		return;
+
+	tc.channels[1] = -1;
+
+	if (tc.bits == 16) {
+		of_property_read_u32_index(node, "reg", 1, &tc.channels[1]);
+		if (tc.channels[1] == -1) {
+			pr_err("%s: clocksource needs two channels\n",
+			       node->parent->full_name);
+		}
+	}
+
+	tc.irq = tcb_irq_get(node, tc.channels[0]);
+	if (tc.irq < 0)
+		return;
+
+	tc.clk[0] = tcb_clk_get(node, tc.channels[0]);
+	if (IS_ERR(tc.clk[0]))
+		return;
+	err = clk_prepare_enable(tc.clk[0]);
+	if (err) {
+		pr_debug("can't enable T0 clk\n");
+		goto err_clk;
+	}
+
+	if (tc.bits == 16) {
+		tc.clk[1] = tcb_clk_get(node, tc.channels[1]);
+		if (IS_ERR(tc.clk[1]))
+			goto err_disable_t0;
+	}
+
+	/* How fast will we be counting?  Pick something over 5 MHz.  */
+	rate = (u32)clk_get_rate(tc.clk[0]);
+	for (i = 0; i < 5; i++) {
+		unsigned int divisor = atmel_tc_divisors[i];
+		unsigned int tmp;
+
+		if (!divisor)
+			continue;
+
+		tmp = rate / divisor;
+		pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
+		if (best_divisor_idx > 0) {
+			if (tmp < 5 * 1000 * 1000)
+				continue;
+		}
+		divided_rate = tmp;
+		best_divisor_idx = i;
+	}
+
+	pr_debug("%s: %s at %d.%03d MHz\n", tc.clksrc.name,
+		 node->parent->full_name, divided_rate / 1000000,
+		 ((divided_rate + 500000) % 1000000) / 1000);
+
+	if (tc.bits == 32) {
+		tc.clksrc.read = tc_get_cycles32;
+		tcb_setup_single_chan(&tc, best_divisor_idx);
+	} else {
+		err = clk_prepare_enable(tc.clk[1]);
+		if (err) {
+			pr_debug("can't enable T1 clk\n");
+			goto err_clk1;
+		}
+		tc.clksrc.read = tc_get_cycles,
+		tcb_setup_dual_chan(&tc, best_divisor_idx);
+	}
+
+	err = clocksource_register_hz(&tc.clksrc, divided_rate);
+	if (err)
+		goto err_disable_t1;
+
+	if (tc.bits == 32)
+		sched_clock_register(tc_sched_clock_read32, 32, divided_rate);
+	else
+		sched_clock_register(tc_sched_clock_read, 32, divided_rate);
+
+	tc.registered = true;
+
+	/* Set up and register clockevents */
+	tc.clkevt.cpumask = cpumask_of(0);
+	tc.clkevt.set_next_event = tcb_clkevt_next_event;
+	tc.clkevt.set_state_oneshot = tcb_clkevt_oneshot;
+	tc.clkevt.set_state_shutdown = tcb_clkevt_shutdown;
+	if (tc.bits == 16)
+		clockevents_config_and_register(&tc.clkevt, divided_rate, 1,
+						0xffff);
+	else
+		clockevents_config_and_register(&tc.clkevt, divided_rate, 1,
+						0xffffffff);
+	return;
+
+err_disable_t1:
+	if (tc.bits == 16)
+		clk_disable_unprepare(tc.clk[1]);
+
+err_clk1:
+	if (tc.bits == 16)
+		clk_put(tc.clk[1]);
+
+err_disable_t0:
+	clk_disable_unprepare(tc.clk[0]);
+
+err_clk:
+	clk_put(tc.clk[0]);
+
+	pr_err("%s: unable to register clocksource/clockevent\n",
+	       tc.clksrc.name);
+}
+CLOCKSOURCE_OF_DECLARE(atmel_tcb_clksrc, "atmel,tcb-clksrc",
+		       tcb_clksrc_init);
diff --git a/include/soc/at91/atmel_tcb.h b/include/soc/at91/atmel_tcb.h
new file mode 100644
index 000000000000..ceb279810ce4
--- /dev/null
+++ b/include/soc/at91/atmel_tcb.h
@@ -0,0 +1,220 @@
+/*
+ * Copyright (C) 2016 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __SOC_ATMEL_TCB_H
+#define __SOC_ATMEL_TCB_H
+
+/* Channel registers */
+#define ATMEL_TC_COFFS(c)		((c) * 0x40)
+#define ATMEL_TC_CCR(c)			ATMEL_TC_COFFS(c)
+#define ATMEL_TC_CMR(c)			(ATMEL_TC_COFFS(c) + 0x4)
+#define ATMEL_TC_SMMR(c)		(ATMEL_TC_COFFS(c) + 0x8)
+#define ATMEL_TC_RAB(c)			(ATMEL_TC_COFFS(c) + 0xc)
+#define ATMEL_TC_CV(c)			(ATMEL_TC_COFFS(c) + 0x10)
+#define ATMEL_TC_RA(c)			(ATMEL_TC_COFFS(c) + 0x14)
+#define ATMEL_TC_RB(c)			(ATMEL_TC_COFFS(c) + 0x18)
+#define ATMEL_TC_RC(c)			(ATMEL_TC_COFFS(c) + 0x1c)
+#define ATMEL_TC_SR(c)			(ATMEL_TC_COFFS(c) + 0x20)
+#define ATMEL_TC_IER(c)			(ATMEL_TC_COFFS(c) + 0x24)
+#define ATMEL_TC_IDR(c)			(ATMEL_TC_COFFS(c) + 0x28)
+#define ATMEL_TC_IMR(c)			(ATMEL_TC_COFFS(c) + 0x2c)
+#define ATMEL_TC_EMR(c)			(ATMEL_TC_COFFS(c) + 0x30)
+
+/* Block registers */
+#define ATMEL_TC_BCR			0xc0
+#define ATMEL_TC_BMR			0xc4
+#define ATMEL_TC_QIER			0xc8
+#define ATMEL_TC_QIDR			0xcc
+#define ATMEL_TC_QIMR			0xd0
+#define ATMEL_TC_QISR			0xd4
+#define ATMEL_TC_FMR			0xd8
+#define ATMEL_TC_WPMR			0xe4
+
+/* CCR fields */
+#define ATMEL_TC_CCR_CLKEN		BIT(0)
+#define ATMEL_TC_CCR_CLKDIS		BIT(1)
+#define ATMEL_TC_CCR_SWTRG		BIT(2)
+
+/* Common CMR fields */
+#define ATMEL_TC_CMR_TCLKS_MSK		GENMASK(2, 0)
+#define ATMEL_TC_CMR_TCLK(x)		(x)
+#define ATMEL_TC_CMR_XC(x)		((x) + 5)
+#define ATMEL_TC_CMR_CLKI		BIT(3)
+#define ATMEL_TC_CMR_BURST_MSK		GENMASK(5, 4)
+#define ATMEL_TC_CMR_BURST_XC(x)	(((x) + 1) << 4)
+#define ATMEL_TC_CMR_WAVE		BIT(15)
+
+/* Capture mode CMR fields */
+#define ATMEL_TC_CMR_LDBSTOP		BIT(6)
+#define ATMEL_TC_CMR_LDBDIS		BIT(7)
+#define ATMEL_TC_CMR_ETRGEDG_MSK	GENMASK(9, 8)
+#define ATMEL_TC_CMR_ETRGEDG_NONE	(0 << 8)
+#define ATMEL_TC_CMR_ETRGEDG_RISING	(1 << 8)
+#define ATMEL_TC_CMR_ETRGEDG_FALLING	(2 << 8)
+#define ATMEL_TC_CMR_ETRGEDG_BOTH	(3 << 8)
+#define ATMEL_TC_CMR_ABETRG		BIT(10)
+#define ATMEL_TC_CMR_CPCTRG		BIT(14)
+#define ATMEL_TC_CMR_LDRA_MSK		GENMASK(17, 16)
+#define ATMEL_TC_CMR_LDRA_NONE		(0 << 16)
+#define ATMEL_TC_CMR_LDRA_RISING	(1 << 16)
+#define ATMEL_TC_CMR_LDRA_FALLING	(2 << 16)
+#define ATMEL_TC_CMR_LDRA_BOTH		(3 << 16)
+#define ATMEL_TC_CMR_LDRB_MSK		GENMASK(19, 18)
+#define ATMEL_TC_CMR_LDRB_NONE		(0 << 18)
+#define ATMEL_TC_CMR_LDRB_RISING	(1 << 18)
+#define ATMEL_TC_CMR_LDRB_FALLING	(2 << 18)
+#define ATMEL_TC_CMR_LDRB_BOTH		(3 << 18)
+#define ATMEL_TC_CMR_SBSMPLR_MSK	GENMASK(22, 20)
+#define ATMEL_TC_CMR_SBSMPLR(x)		((x) << 20)
+
+/* Waveform mode CMR fields */
+#define ATMEL_TC_CMR_CPCSTOP		BIT(6)
+#define ATMEL_TC_CMR_CPCDIS		BIT(7)
+#define ATMEL_TC_CMR_EEVTEDG_MSK	GENMASK(9, 8)
+#define ATMEL_TC_CMR_EEVTEDG_NONE	(0 << 8)
+#define ATMEL_TC_CMR_EEVTEDG_RISING	(1 << 8)
+#define ATMEL_TC_CMR_EEVTEDG_FALLING	(2 << 8)
+#define ATMEL_TC_CMR_EEVTEDG_BOTH	(3 << 8)
+#define ATMEL_TC_CMR_EEVT_MSK		GENMASK(11, 10)
+#define ATMEL_TC_CMR_EEVT_XC(x)		(((x) + 1) << 10)
+#define ATMEL_TC_CMR_ENETRG		BIT(12)
+#define ATMEL_TC_CMR_WAVESEL_MSK	GENMASK(14, 13)
+#define ATMEL_TC_CMR_WAVESEL_UP		(0 << 13)
+#define ATMEL_TC_CMR_WAVESEL_UPDOWN	(1 << 13)
+#define ATMEL_TC_CMR_WAVESEL_UPRC	(2 << 13)
+#define ATMEL_TC_CMR_WAVESEL_UPDOWNRC	(3 << 13)
+#define ATMEL_TC_CMR_ACPA_MSK		GENMASK(17, 16)
+#define ATMEL_TC_CMR_ACPA(a)		(ATMEL_TC_CMR_ACTION_##a << 16)
+#define ATMEL_TC_CMR_ACPC_MSK		GENMASK(19, 18)
+#define ATMEL_TC_CMR_ACPC(a)		(ATMEL_TC_CMR_ACTION_##a << 18)
+#define ATMEL_TC_CMR_AEEVT_MSK		GENMASK(21, 20)
+#define ATMEL_TC_CMR_AEEVT(a)		(ATMEL_TC_CMR_ACTION_##a << 20)
+#define ATMEL_TC_CMR_ASWTRG_MSK		GENMASK(23, 22)
+#define ATMEL_TC_CMR_ASWTRG(a)		(ATMEL_TC_CMR_ACTION_##a << 22)
+#define ATMEL_TC_CMR_BCPB_MSK		GENMASK(25, 24)
+#define ATMEL_TC_CMR_BCPB(a)		(ATMEL_TC_CMR_ACTION_##a << 24)
+#define ATMEL_TC_CMR_BCPC_MSK		GENMASK(27, 26)
+#define ATMEL_TC_CMR_BCPC(a)		(ATMEL_TC_CMR_ACTION_##a << 26)
+#define ATMEL_TC_CMR_BEEVT_MSK		GENMASK(29, 28)
+#define ATMEL_TC_CMR_BEEVT(a)		(ATMEL_TC_CMR_ACTION_##a << 28)
+#define ATMEL_TC_CMR_BSWTRG_MSK		GENMASK(31, 30)
+#define ATMEL_TC_CMR_BSWTRG(a)		(ATMEL_TC_CMR_ACTION_##a << 30)
+#define ATMEL_TC_CMR_ACTION_NONE	0
+#define ATMEL_TC_CMR_ACTION_SET		1
+#define ATMEL_TC_CMR_ACTION_CLEAR	2
+#define ATMEL_TC_CMR_ACTION_TOGGLE	3
+
+/* SMMR fields */
+#define ATMEL_TC_SMMR_GCEN		BIT(0)
+#define ATMEL_TC_SMMR_DOWN		BIT(1)
+
+/* SR/IER/IDR/IMR fields */
+#define ATMEL_TC_COVFS			BIT(0)
+#define ATMEL_TC_LOVRS			BIT(1)
+#define ATMEL_TC_CPAS			BIT(2)
+#define ATMEL_TC_CPBS			BIT(3)
+#define ATMEL_TC_CPCS			BIT(4)
+#define ATMEL_TC_LDRAS			BIT(5)
+#define ATMEL_TC_LDRBS			BIT(6)
+#define ATMEL_TC_ETRGS			BIT(7)
+#define ATMEL_TC_CLKSTA			BIT(16)
+#define ATMEL_TC_MTIOA			BIT(17)
+#define ATMEL_TC_MTIOB			BIT(18)
+
+/* EMR fields */
+#define ATMEL_TC_EMR_TRIGSRCA_MSK	GENMASK(1, 0)
+#define ATMEL_TC_EMR_TRIGSRCA_TIOA	0
+#define ATMEL_TC_EMR_TRIGSRCA_PWMX	1
+#define ATMEL_TC_EMR_TRIGSRCB_MSK	GENMASK(5, 4)
+#define ATMEL_TC_EMR_TRIGSRCB_TIOB	(0 << 4)
+#define ATMEL_TC_EMR_TRIGSRCB_PWM	(1 << 4)
+#define ATMEL_TC_EMR_NOCLKDIV		BIT(8)
+
+/* BCR fields */
+#define ATMEL_TC_BCR_SYNC		BIT(0)
+
+/* BMR fields */
+#define ATMEL_TC_BMR_TCXC_MSK(c)	GENMASK(((c) * 2) + 1, (c) * 2)
+#define ATMEL_TC_BMR_TCXC(x, c)		((x) << (2 * (c)))
+#define ATMEL_TC_BMR_QDEN		BIT(8)
+#define ATMEL_TC_BMR_POSEN		BIT(9)
+#define ATMEL_TC_BMR_SPEEDEN		BIT(10)
+#define ATMEL_TC_BMR_QDTRANS		BIT(11)
+#define ATMEL_TC_BMR_EDGPHA		BIT(12)
+#define ATMEL_TC_BMR_INVA		BIT(13)
+#define ATMEL_TC_BMR_INVB		BIT(14)
+#define ATMEL_TC_BMR_INVIDX		BIT(15)
+#define ATMEL_TC_BMR_SWAP		BIT(16)
+#define ATMEL_TC_BMR_IDXPHB		BIT(17)
+#define ATMEL_TC_BMR_AUTOC		BIT(18)
+#define ATMEL_TC_MAXFILT_MSK		GENMASK(25, 20)
+#define ATMEL_TC_MAXFILT(x)		(((x) - 1) << 20)
+#define ATMEL_TC_MAXCMP_MSK		GENMASK(29, 26)
+#define ATMEL_TC_MAXCMP(x)		((x) << 26)
+
+/* QEDC fields */
+#define ATMEL_TC_QEDC_IDX		BIT(0)
+#define ATMEL_TC_QEDC_DIRCHG		BIT(1)
+#define ATMEL_TC_QEDC_QERR		BIT(2)
+#define ATMEL_TC_QEDC_MPE		BIT(3)
+#define ATMEL_TC_QEDC_DIR		BIT(8)
+
+/* FMR fields */
+#define ATMEL_TC_FMR_ENCF(x)		BIT(x)
+
+/* WPMR fields */
+#define ATMEL_TC_WPMR_WPKEY		(0x54494d << 8)
+#define ATMEL_TC_WPMR_WPEN		BIT(0)
+
+static inline struct clk *tcb_clk_get(struct device_node *node, int channel)
+{
+	struct clk *clk;
+	char clk_name[] = "t0_clk";
+
+	clk_name[1] += channel;
+	clk = of_clk_get_by_name(node->parent, clk_name);
+	if (!IS_ERR(clk))
+		return clk;
+
+	return of_clk_get_by_name(node->parent, "t0_clk");
+}
+
+static inline int tcb_irq_get(struct device_node *node, int channel)
+{
+	int irq;
+
+	irq = of_irq_get(node->parent, channel);
+	if (irq > 0)
+		return irq;
+
+	return of_irq_get(node->parent, 0);
+}
+
+static const u8 atmel_tc_divisors[5] = { 2, 8, 32, 128, 0, };
+
+static const struct of_device_id atmel_tcb_dt_ids[] = {
+	{
+		.compatible = "atmel,at91rm9200-tcb",
+		.data = (void *)16,
+	}, {
+		.compatible = "atmel,at91sam9x5-tcb",
+		.data = (void *)32,
+	}, {
+		/* sentinel */
+	}
+};
+
+#endif /* __SOC_ATMEL_TCB_H */
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 43/48] clocksource/drivers: Add a clockevent driver for Atmel TC blocks
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (41 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT Alexandre Belloni
                   ` (4 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Daniel Lezcano, Thomas Gleixner

Add an independent clockevent driver for the Atmel Timer Counter Blocks.
This driver provides a single clockevent device. using its own TCB channel.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 drivers/clocksource/Kconfig                 |  10 ++
 drivers/clocksource/Makefile                |   1 +
 drivers/clocksource/timer-atmel-tcbclkevt.c | 220 ++++++++++++++++++++++++++++
 3 files changed, 231 insertions(+)
 create mode 100644 drivers/clocksource/timer-atmel-tcbclkevt.c

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index ff7f4022c749..1860f6f9b380 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -271,6 +271,16 @@ config ATMEL_ARM_TCB_CLKSRC
 	  to make a single 32-bit timer.
 	  It can also be used as a clock event device supporting oneshot mode.
 
+config ATMEL_ARM_TCB_CLKEVT
+	bool "TC Block Clockevent"
+	select REGMAP_MMIO
+	depends on GENERIC_CLOCKEVENTS
+	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
+	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
+	help
+	  Select this to get a high precision clockevent device based on a TC
+	  Block with the slow clock as its input.
+
 config CLKSRC_METAG_GENERIC
 	def_bool y if METAG
 	help
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 988f33de5808..c4a4155ccedc 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_ATMEL_PIT)		+= timer-atmel-pit.o
 obj-$(CONFIG_ATMEL_ST)		+= timer-atmel-st.o
 obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
 obj-$(CONFIG_ATMEL_ARM_TCB_CLKSRC)	+= timer-atmel-tcbclksrc.o
+obj-$(CONFIG_ATMEL_ARM_TCB_CLKEVT)	+= timer-atmel-tcbclkevt.o
 obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
 obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o
 obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC)	+= cs5535-clockevt.o
diff --git a/drivers/clocksource/timer-atmel-tcbclkevt.c b/drivers/clocksource/timer-atmel-tcbclkevt.c
new file mode 100644
index 000000000000..71440fd27b49
--- /dev/null
+++ b/drivers/clocksource/timer-atmel-tcbclkevt.c
@@ -0,0 +1,220 @@
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <soc/at91/atmel_tcb.h>
+
+struct tc_clkevt_device {
+	struct clock_event_device clkevt;
+	struct regmap *regmap;
+	struct clk *slow_clk;
+	struct clk *clk;
+	int channel;
+	int irq;
+};
+
+static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt)
+{
+	return container_of(clkevt, struct tc_clkevt_device, clkevt);
+}
+
+static int tc_shutdown(struct clock_event_device *d)
+{
+	struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+
+	regmap_write(tcd->regmap, ATMEL_TC_IDR(tcd->channel), 0xff);
+	regmap_write(tcd->regmap, ATMEL_TC_CCR(tcd->channel),
+		     ATMEL_TC_CCR_CLKDIS);
+	if (!clockevent_state_detached(d))
+		clk_disable(tcd->clk);
+
+	return 0;
+}
+
+/* For now, we always use the 32K clock ... this optimizes for NO_HZ,
+ * because using one of the divided clocks would usually mean the
+ * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
+ *
+ * A divided clock could be good for high resolution timers, since
+ * 30.5 usec resolution can seem "low".
+ */
+static int tc_set_oneshot(struct clock_event_device *d)
+{
+	struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+
+	if (clockevent_state_oneshot(d) || clockevent_state_periodic(d))
+		tc_shutdown(d);
+
+	clk_enable(tcd->clk);
+
+	/* slow clock, count up to RC, then irq and stop */
+	regmap_write(tcd->regmap, ATMEL_TC_CMR(tcd->channel),
+		     ATMEL_TC_CMR_TCLK(4) | ATMEL_TC_CMR_CPCSTOP |
+		     ATMEL_TC_CMR_WAVE | ATMEL_TC_CMR_WAVESEL_UPRC);
+	regmap_write(tcd->regmap, ATMEL_TC_IER(tcd->channel),
+		     ATMEL_TC_CPCS);
+
+	return 0;
+}
+
+static int tc_set_periodic(struct clock_event_device *d)
+{
+	struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+
+	if (clockevent_state_oneshot(d) || clockevent_state_periodic(d))
+		tc_shutdown(d);
+
+	/* By not making the gentime core emulate periodic mode on top
+	 * of oneshot, we get lower overhead and improved accuracy.
+	 */
+	clk_enable(tcd->clk);
+
+	/* slow clock, count up to RC, then irq and restart */
+	regmap_write(tcd->regmap, ATMEL_TC_CMR(tcd->channel),
+		     ATMEL_TC_CMR_TCLK(4) | ATMEL_TC_CMR_WAVE |
+		     ATMEL_TC_CMR_WAVESEL_UPRC);
+	regmap_write(tcd->regmap, ATMEL_TC_RC(tcd->channel),
+		     (32768 + HZ / 2) / HZ);
+
+	/* Enable clock and interrupts on RC compare */
+	regmap_write(tcd->regmap, ATMEL_TC_IER(tcd->channel), ATMEL_TC_CPCS);
+	regmap_write(tcd->regmap, ATMEL_TC_CCR(tcd->channel),
+		     ATMEL_TC_CCR_CLKEN | ATMEL_TC_CCR_SWTRG);
+
+	return 0;
+}
+
+static int tc_next_event(unsigned long delta, struct clock_event_device *d)
+{
+	struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+
+	regmap_write(tcd->regmap, ATMEL_TC_RC(tcd->channel), delta);
+	regmap_write(tcd->regmap, ATMEL_TC_CCR(tcd->channel),
+		     ATMEL_TC_CCR_CLKEN | ATMEL_TC_CCR_SWTRG);
+
+	return 0;
+}
+
+static struct tc_clkevt_device clkevt = {
+	.clkevt	= {
+		.features		= CLOCK_EVT_FEAT_PERIODIC |
+					  CLOCK_EVT_FEAT_ONESHOT,
+		/* Should be lower than at91rm9200's system timer */
+		.rating			= 140,
+		.set_next_event		= tc_next_event,
+		.set_state_shutdown	= tc_shutdown,
+		.set_state_periodic	= tc_set_periodic,
+		.set_state_oneshot	= tc_set_oneshot,
+	},
+};
+
+static irqreturn_t tc_clkevt_irq(int irq, void *handle)
+{
+	struct tc_clkevt_device	*tcd = handle;
+	unsigned int		sr;
+
+	regmap_read(tcd->regmap, ATMEL_TC_SR(tcd->channel), &sr);
+	if (sr & ATMEL_TC_CPCS) {
+		tcd->clkevt.event_handler(&tcd->clkevt);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int tcb_clkevt_probe(struct platform_device *pdev)
+{
+	struct tc_clkevt_device *tcd = &clkevt;
+	int ret;
+	struct device_node *node = pdev->dev.of_node;
+
+	ret = of_property_read_u32_index(node, "reg", 0, &tcd->channel);
+	if (ret)
+		return ret;
+
+	tcd->irq = tcb_irq_get(node, tcd->channel);
+	if (tcd->irq < 0)
+		return tcd->irq;
+
+	tcd->regmap = syscon_node_to_regmap(node->parent);
+	if (IS_ERR(tcd->regmap))
+		return PTR_ERR(tcd->regmap);
+
+	tcd->slow_clk = of_clk_get_by_name(node->parent, "slow_clk");
+	if (IS_ERR(tcd->slow_clk))
+		return PTR_ERR(tcd->slow_clk);
+
+	ret = clk_prepare_enable(tcd->slow_clk);
+	if (ret)
+		return ret;
+
+	tcd->clk = tcb_clk_get(node, tcd->channel);
+	if (IS_ERR(tcd->clk)) {
+		ret = PTR_ERR(tcd->clk);
+		goto err_slow;
+	}
+
+	clkevt.clkevt.name = dev_name(&pdev->dev);
+
+	/* try to enable clk to avoid future errors in mode change */
+	ret = clk_prepare_enable(tcd->clk);
+	if (ret)
+		goto err_slow;
+
+	clk_disable(tcd->clk);
+
+	clkevt.clkevt.cpumask = cpumask_of(0);
+
+	clockevents_config_and_register(&clkevt.clkevt, 32768, 1, 0xffff);
+
+	ret = request_irq(tcd->irq, tc_clkevt_irq, IRQF_TIMER | IRQF_SHARED,
+			  clkevt.clkevt.name, &clkevt);
+	if (ret)
+		goto err_clk;
+
+	return 0;
+
+err_clk:
+	clk_unprepare(tcd->clk);
+err_slow:
+	clk_disable_unprepare(tcd->slow_clk);
+
+	return ret;
+}
+
+static const struct of_device_id atmel_tcb_clkevt_dt_ids[] = {
+	{ .compatible = "atmel,tcb-clkevt" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_tcb_clkevt_dt_ids);
+
+static struct platform_driver tcb_clkevt_driver = {
+	.probe		= tcb_clkevt_probe,
+	.driver         = {
+		.name   = "atmel_tcb_clkevt",
+		.of_match_table = of_match_ptr(atmel_tcb_clkevt_dt_ids),
+	},
+};
+
+static int __init atmel_tcb_clkevt_init(void)
+{
+	return platform_driver_register(&tcb_clkevt_driver);
+}
+
+static void __exit atmel_tcb_clkevt_exit(void)
+{
+	platform_driver_unregister(&tcb_clkevt_driver);
+}
+
+early_platform_init("earlytimer", &tcb_clkevt_driver);
+subsys_initcall(atmel_tcb_clkevt_init);
+module_exit(atmel_tcb_clkevt_exit);
+
+MODULE_AUTHOR("Alexandre Belloni <alexandre.belloni@free-electrons.com>");
+MODULE_DESCRIPTION("Clockevents driver for Atmel Timer Counter Blocks");
+MODULE_LICENSE("GPL v2");
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (42 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 43/48] clocksource/drivers: Add a clockevent driver for Atmel " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-11  9:43   ` Thomas Gleixner
  2016-06-10 22:03 ` [PATCH 45/48] ARM: at91/defconfig: sama5: unselect ATMEL_PIT Alexandre Belloni
                   ` (3 subsequent siblings)
  47 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Daniel Lezcano, Thomas Gleixner

With the new TCB clocksource driver, atmel platforms are now able to boot
without the PIT driver. Allow unselecting it.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 drivers/clocksource/Kconfig | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 1860f6f9b380..c651661bf43c 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -251,7 +251,14 @@ config ARMV7M_SYSTICK
 
 config ATMEL_PIT
 	select CLKSRC_OF if OF
-	def_bool SOC_AT91SAM9 || SOC_SAMA5
+	bool "Atmel Periodic Interval Timer (PIT)"
+	depends on SOC_AT91SAM9 || SOC_SAMA5
+	default SOC_AT91SAM9 || SOC_SAMA5
+	help
+	  Select this to get a clocksource based on the Atmel Periodic Interval
+	  Timer. It has a relatively low resolution and the TC Block clocksource
+	  should be preferred.
+	  It also provides a clock event device.
 
 config ATMEL_ST
 	bool
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 45/48] ARM: at91/defconfig: sama5: unselect ATMEL_PIT
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (43 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 46/48] ARM: at91/defconfig: at91_dt " Alexandre Belloni
                   ` (2 subsequent siblings)
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

The PIT is not required anymore to successfully boot and may actually harm
in case preempt-rt is used because the PIT interrupt is shared.
Disable it so the TCB clocksource is used.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/configs/sama5_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index 9cb1a85bb166..c17a13487bea 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -192,6 +192,7 @@ CONFIG_RTC_DRV_AT91RM9200=y
 CONFIG_DMADEVICES=y
 CONFIG_AT_HDMAC=y
 CONFIG_AT_XDMAC=y
+# CONFIG_ATMEL_PIT is not set
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_IIO=y
 CONFIG_AT91_ADC=y
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 46/48] ARM: at91/defconfig: at91_dt unselect ATMEL_PIT
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (44 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 45/48] ARM: at91/defconfig: sama5: unselect ATMEL_PIT Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 47/48] PWM: atmel-tcb: switch to new binding Alexandre Belloni
  2016-06-10 22:03 ` [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding Alexandre Belloni
  47 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni

The PIT is not required anymore to successfully boot and may actually harm
in case preempt-rt is used because the PIT interrupt is shared.
Disable it so the TCB clocksource is used.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/configs/at91_dt_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
index e4b1be66b3f5..9d068f07b84b 100644
--- a/arch/arm/configs/at91_dt_defconfig
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -182,6 +182,7 @@ CONFIG_RTC_DRV_AT91RM9200=y
 CONFIG_RTC_DRV_AT91SAM9=y
 CONFIG_DMADEVICES=y
 CONFIG_AT_HDMAC=y
+# CONFIG_ATMEL_PIT is not set
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_IIO=y
 CONFIG_AT91_ADC=y
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 47/48] PWM: atmel-tcb: switch to new binding
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (45 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 46/48] ARM: at91/defconfig: at91_dt " Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-11  2:22   ` kbuild test robot
  2016-06-10 22:03 ` [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding Alexandre Belloni
  47 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Thierry Reding, linux-pwm

The PWM is now a subnode of the used TCB. This is cleaner and it mainly
allows to stop wasting TCB channels when only 4 PWMs are used.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 drivers/pwm/Kconfig         |   3 +-
 drivers/pwm/pwm-atmel-tcb.c | 219 ++++++++++++++++++++++++--------------------
 2 files changed, 120 insertions(+), 102 deletions(-)

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index c182efc62c7b..431a68c2e82f 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -64,7 +64,8 @@ config PWM_ATMEL_HLCDC_PWM
 
 config PWM_ATMEL_TCB
 	tristate "Atmel TC Block PWM support"
-	depends on ATMEL_TCLIB && OF
+	depends on OF
+	select REGMAP_MMIO
 	help
 	  Generic PWM framework driver for Atmel Timer Counter Block.
 
diff --git a/drivers/pwm/pwm-atmel-tcb.c b/drivers/pwm/pwm-atmel-tcb.c
index 75db585a2a94..5afb5116ad96 100644
--- a/drivers/pwm/pwm-atmel-tcb.c
+++ b/drivers/pwm/pwm-atmel-tcb.c
@@ -16,19 +16,26 @@
 #include <linux/err.h>
 #include <linux/ioport.h>
 #include <linux/io.h>
+#include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
-#include <linux/atmel_tc.h>
 #include <linux/pwm.h>
 #include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
 #include <linux/slab.h>
+#include <soc/at91/atmel_tcb.h>
 
-#define NPWM	6
+#define NPWM	2
 
-#define ATMEL_TC_ACMR_MASK	(ATMEL_TC_ACPA | ATMEL_TC_ACPC |	\
-				 ATMEL_TC_AEEVT | ATMEL_TC_ASWTRG)
+#define ATMEL_TC_ACMR_MASK	(ATMEL_TC_CMR_ACPA_MSK | \
+				 ATMEL_TC_CMR_ACPC_MSK | \
+				 ATMEL_TC_CMR_AEEVT_MSK | \
+				 ATMEL_TC_CMR_ASWTRG_MSK)
 
-#define ATMEL_TC_BCMR_MASK	(ATMEL_TC_BCPB | ATMEL_TC_BCPC |	\
-				 ATMEL_TC_BEEVT | ATMEL_TC_BSWTRG)
+#define ATMEL_TC_BCMR_MASK	(ATMEL_TC_CMR_BCPB_MSK | \
+				 ATMEL_TC_CMR_BCPC_MSK | \
+				 ATMEL_TC_CMR_BEEVT_MSK | \
+				 ATMEL_TC_CMR_BSWTRG_MSK)
 
 struct atmel_tcb_pwm_device {
 	enum pwm_polarity polarity;	/* PWM polarity */
@@ -40,7 +47,11 @@ struct atmel_tcb_pwm_device {
 struct atmel_tcb_pwm_chip {
 	struct pwm_chip chip;
 	spinlock_t lock;
-	struct atmel_tc *tc;
+	u8 channel;
+	u8 width;
+	struct regmap *regmap;
+	struct clk *clk;
+	struct clk *slow_clk;
 	struct atmel_tcb_pwm_device *pwms[NPWM];
 };
 
@@ -65,10 +76,6 @@ static int atmel_tcb_pwm_request(struct pwm_chip *chip,
 {
 	struct atmel_tcb_pwm_chip *tcbpwmc = to_tcb_chip(chip);
 	struct atmel_tcb_pwm_device *tcbpwm;
-	struct atmel_tc *tc = tcbpwmc->tc;
-	void __iomem *regs = tc->regs;
-	unsigned group = pwm->hwpwm / 2;
-	unsigned index = pwm->hwpwm % 2;
 	unsigned cmr;
 	int ret;
 
@@ -76,7 +83,7 @@ static int atmel_tcb_pwm_request(struct pwm_chip *chip,
 	if (!tcbpwm)
 		return -ENOMEM;
 
-	ret = clk_prepare_enable(tc->clk[group]);
+	ret = clk_prepare_enable(tcbpwmc->clk);
 	if (ret) {
 		devm_kfree(chip->dev, tcbpwm);
 		return ret;
@@ -89,28 +96,32 @@ static int atmel_tcb_pwm_request(struct pwm_chip *chip,
 	tcbpwm->div = 0;
 
 	spin_lock(&tcbpwmc->lock);
-	cmr = __raw_readl(regs + ATMEL_TC_REG(group, CMR));
+	regmap_read(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), &cmr);
 	/*
 	 * Get init config from Timer Counter registers if
 	 * Timer Counter is already configured as a PWM generator.
 	 */
-	if (cmr & ATMEL_TC_WAVE) {
-		if (index == 0)
-			tcbpwm->duty =
-				__raw_readl(regs + ATMEL_TC_REG(group, RA));
+	if (cmr & ATMEL_TC_CMR_WAVE) {
+		if (pwm->hwpwm == 0)
+			regmap_read(tcbpwmc->regmap,
+				    ATMEL_TC_RA(tcbpwmc->channel),
+				    &tcbpwm->duty);
 		else
-			tcbpwm->duty =
-				__raw_readl(regs + ATMEL_TC_REG(group, RB));
-
-		tcbpwm->div = cmr & ATMEL_TC_TCCLKS;
-		tcbpwm->period = __raw_readl(regs + ATMEL_TC_REG(group, RC));
-		cmr &= (ATMEL_TC_TCCLKS | ATMEL_TC_ACMR_MASK |
+			regmap_read(tcbpwmc->regmap,
+				    ATMEL_TC_RB(tcbpwmc->channel),
+				    &tcbpwm->duty);
+
+		tcbpwm->div = cmr & ATMEL_TC_CMR_TCLKS_MSK;
+		regmap_read(tcbpwmc->regmap, ATMEL_TC_RC(tcbpwmc->channel),
+			    &tcbpwm->period);
+		cmr &= (ATMEL_TC_CMR_TCLKS_MSK | ATMEL_TC_ACMR_MASK |
 			ATMEL_TC_BCMR_MASK);
 	} else
 		cmr = 0;
 
-	cmr |= ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO | ATMEL_TC_EEVT_XC0;
-	__raw_writel(cmr, regs + ATMEL_TC_REG(group, CMR));
+	cmr |= ATMEL_TC_CMR_WAVE | ATMEL_TC_CMR_WAVESEL_UPRC |
+	       ATMEL_TC_CMR_EEVT_XC(0);
+	regmap_write(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), cmr);
 	spin_unlock(&tcbpwmc->lock);
 
 	tcbpwmc->pwms[pwm->hwpwm] = tcbpwm;
@@ -122,9 +133,8 @@ static void atmel_tcb_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct atmel_tcb_pwm_chip *tcbpwmc = to_tcb_chip(chip);
 	struct atmel_tcb_pwm_device *tcbpwm = pwm_get_chip_data(pwm);
-	struct atmel_tc *tc = tcbpwmc->tc;
 
-	clk_disable_unprepare(tc->clk[pwm->hwpwm / 2]);
+	clk_disable_unprepare(tcbpwmc->clk);
 	tcbpwmc->pwms[pwm->hwpwm] = NULL;
 	devm_kfree(chip->dev, tcbpwm);
 }
@@ -133,10 +143,6 @@ static void atmel_tcb_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct atmel_tcb_pwm_chip *tcbpwmc = to_tcb_chip(chip);
 	struct atmel_tcb_pwm_device *tcbpwm = pwm_get_chip_data(pwm);
-	struct atmel_tc *tc = tcbpwmc->tc;
-	void __iomem *regs = tc->regs;
-	unsigned group = pwm->hwpwm / 2;
-	unsigned index = pwm->hwpwm % 2;
 	unsigned cmr;
 	enum pwm_polarity polarity = tcbpwm->polarity;
 
@@ -152,35 +158,35 @@ static void atmel_tcb_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 		polarity = !polarity;
 
 	spin_lock(&tcbpwmc->lock);
-	cmr = __raw_readl(regs + ATMEL_TC_REG(group, CMR));
+	regmap_read(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), &cmr);
 
 	/* flush old setting and set the new one */
-	if (index == 0) {
+	if (pwm->hwpwm == 0) {
 		cmr &= ~ATMEL_TC_ACMR_MASK;
 		if (polarity == PWM_POLARITY_INVERSED)
-			cmr |= ATMEL_TC_ASWTRG_CLEAR;
+			cmr |= ATMEL_TC_CMR_ASWTRG(CLEAR);
 		else
-			cmr |= ATMEL_TC_ASWTRG_SET;
+			cmr |= ATMEL_TC_CMR_ASWTRG(SET);
 	} else {
 		cmr &= ~ATMEL_TC_BCMR_MASK;
 		if (polarity == PWM_POLARITY_INVERSED)
-			cmr |= ATMEL_TC_BSWTRG_CLEAR;
+			cmr |= ATMEL_TC_CMR_BSWTRG(CLEAR);
 		else
-			cmr |= ATMEL_TC_BSWTRG_SET;
+			cmr |= ATMEL_TC_CMR_BSWTRG(SET);
 	}
 
-	__raw_writel(cmr, regs + ATMEL_TC_REG(group, CMR));
+	regmap_write(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), cmr);
 
 	/*
 	 * Use software trigger to apply the new setting.
 	 * If both PWM devices in this group are disabled we stop the clock.
 	 */
-	if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC)))
-		__raw_writel(ATMEL_TC_SWTRG | ATMEL_TC_CLKDIS,
-			     regs + ATMEL_TC_REG(group, CCR));
+	if (!(cmr & (ATMEL_TC_CMR_ACPC_MSK | ATMEL_TC_CMR_BCPC_MSK)))
+		regmap_write(tcbpwmc->regmap, ATMEL_TC_CCR(tcbpwmc->channel),
+			     ATMEL_TC_CCR_SWTRG | ATMEL_TC_CCR_CLKDIS);
 	else
-		__raw_writel(ATMEL_TC_SWTRG, regs +
-			     ATMEL_TC_REG(group, CCR));
+		regmap_write(tcbpwmc->regmap, ATMEL_TC_CCR(tcbpwmc->channel),
+			     ATMEL_TC_CCR_SWTRG);
 
 	spin_unlock(&tcbpwmc->lock);
 }
@@ -189,10 +195,6 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct atmel_tcb_pwm_chip *tcbpwmc = to_tcb_chip(chip);
 	struct atmel_tcb_pwm_device *tcbpwm = pwm_get_chip_data(pwm);
-	struct atmel_tc *tc = tcbpwmc->tc;
-	void __iomem *regs = tc->regs;
-	unsigned group = pwm->hwpwm / 2;
-	unsigned index = pwm->hwpwm % 2;
 	u32 cmr;
 	enum pwm_polarity polarity = tcbpwm->polarity;
 
@@ -208,25 +210,25 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 		polarity = !polarity;
 
 	spin_lock(&tcbpwmc->lock);
-	cmr = __raw_readl(regs + ATMEL_TC_REG(group, CMR));
+	regmap_read(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), &cmr);
 
 	/* flush old setting and set the new one */
-	cmr &= ~ATMEL_TC_TCCLKS;
+	cmr &= ~ATMEL_TC_CMR_TCLKS_MSK;
 
-	if (index == 0) {
+	if (pwm->hwpwm == 0) {
 		cmr &= ~ATMEL_TC_ACMR_MASK;
 
 		/* Set CMR flags according to given polarity */
 		if (polarity == PWM_POLARITY_INVERSED)
-			cmr |= ATMEL_TC_ASWTRG_CLEAR;
+			cmr |= ATMEL_TC_CMR_ASWTRG(CLEAR);
 		else
-			cmr |= ATMEL_TC_ASWTRG_SET;
+			cmr |= ATMEL_TC_CMR_ASWTRG(SET);
 	} else {
 		cmr &= ~ATMEL_TC_BCMR_MASK;
 		if (polarity == PWM_POLARITY_INVERSED)
-			cmr |= ATMEL_TC_BSWTRG_CLEAR;
+			cmr |= ATMEL_TC_CMR_BSWTRG(CLEAR);
 		else
-			cmr |= ATMEL_TC_BSWTRG_SET;
+			cmr |= ATMEL_TC_CMR_BSWTRG(SET);
 	}
 
 	/*
@@ -236,33 +238,40 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 	 * this config till next config call.
 	 */
 	if (tcbpwm->duty != tcbpwm->period && tcbpwm->duty > 0) {
-		if (index == 0) {
+		if (pwm->hwpwm == 0) {
 			if (polarity == PWM_POLARITY_INVERSED)
-				cmr |= ATMEL_TC_ACPA_SET | ATMEL_TC_ACPC_CLEAR;
+				cmr |= ATMEL_TC_CMR_ACPA(SET) |
+				       ATMEL_TC_CMR_ACPC(CLEAR);
 			else
-				cmr |= ATMEL_TC_ACPA_CLEAR | ATMEL_TC_ACPC_SET;
+				cmr |= ATMEL_TC_CMR_ACPA(CLEAR) |
+				       ATMEL_TC_CMR_ACPC(SET);
 		} else {
 			if (polarity == PWM_POLARITY_INVERSED)
-				cmr |= ATMEL_TC_BCPB_SET | ATMEL_TC_BCPC_CLEAR;
+				cmr |= ATMEL_TC_CMR_BCPB(SET) |
+				       ATMEL_TC_CMR_BCPC(CLEAR);
 			else
-				cmr |= ATMEL_TC_BCPB_CLEAR | ATMEL_TC_BCPC_SET;
+				cmr |= ATMEL_TC_CMR_BCPB(CLEAR) |
+				       ATMEL_TC_CMR_BCPC(SET);
 		}
 	}
 
-	cmr |= (tcbpwm->div & ATMEL_TC_TCCLKS);
+	cmr |= (tcbpwm->div & ATMEL_TC_CMR_TCLKS_MSK);
 
-	__raw_writel(cmr, regs + ATMEL_TC_REG(group, CMR));
+	regmap_write(tcbpwmc->regmap, ATMEL_TC_CMR(tcbpwmc->channel), cmr);
 
-	if (index == 0)
-		__raw_writel(tcbpwm->duty, regs + ATMEL_TC_REG(group, RA));
+	if (pwm->hwpwm == 0)
+		regmap_write(tcbpwmc->regmap, ATMEL_TC_RA(tcbpwmc->channel),
+			     tcbpwm->duty);
 	else
-		__raw_writel(tcbpwm->duty, regs + ATMEL_TC_REG(group, RB));
+		regmap_write(tcbpwmc->regmap, ATMEL_TC_RB(tcbpwmc->channel),
+			     tcbpwm->duty);
 
-	__raw_writel(tcbpwm->period, regs + ATMEL_TC_REG(group, RC));
+	regmap_write(tcbpwmc->regmap, ATMEL_TC_RC(tcbpwmc->channel),
+		     tcbpwm->period);
 
 	/* Use software trigger to apply the new setting */
-	__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
-		     regs + ATMEL_TC_REG(group, CCR));
+	regmap_write(tcbpwmc->regmap, ATMEL_TC_CCR(tcbpwmc->channel),
+		     ATMEL_TC_CCR_SWTRG | ATMEL_TC_CCR_CLKEN);
 	spin_unlock(&tcbpwmc->lock);
 	return 0;
 }
@@ -272,15 +281,12 @@ static int atmel_tcb_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 {
 	struct atmel_tcb_pwm_chip *tcbpwmc = to_tcb_chip(chip);
 	struct atmel_tcb_pwm_device *tcbpwm = pwm_get_chip_data(pwm);
-	unsigned group = pwm->hwpwm / 2;
-	unsigned index = pwm->hwpwm % 2;
 	struct atmel_tcb_pwm_device *atcbpwm = NULL;
-	struct atmel_tc *tc = tcbpwmc->tc;
 	int i;
 	int slowclk = 0;
 	unsigned period;
 	unsigned duty;
-	unsigned rate = clk_get_rate(tc->clk[group]);
+	unsigned rate = clk_get_rate(tcbpwmc->clk);
 	unsigned long long min;
 	unsigned long long max;
 
@@ -294,7 +300,7 @@ static int atmel_tcb_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 			continue;
 		}
 		min = div_u64((u64)NSEC_PER_SEC * atmel_tc_divisors[i], rate);
-		max = min << tc->tcb_config->counter_width;
+		max = min << tcbpwmc->width;
 		if (max >= period_ns)
 			break;
 	}
@@ -305,9 +311,9 @@ static int atmel_tcb_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 	 */
 	if (i == 5) {
 		i = slowclk;
-		rate = clk_get_rate(tc->slow_clk);
+		rate = clk_get_rate(tcbpwmc->slow_clk);
 		min = div_u64(NSEC_PER_SEC, rate);
-		max = min << tc->tcb_config->counter_width;
+		max = min << tcbpwmc->width;
 
 		/* If period is too big return ERANGE error */
 		if (max < period_ns)
@@ -317,17 +323,13 @@ static int atmel_tcb_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
 	duty = div_u64(duty_ns, min);
 	period = div_u64(period_ns, min);
 
-	if (index == 0)
-		atcbpwm = tcbpwmc->pwms[pwm->hwpwm + 1];
+	if (pwm->hwpwm == 0)
+		atcbpwm = tcbpwmc->pwms[1];
 	else
-		atcbpwm = tcbpwmc->pwms[pwm->hwpwm - 1];
+		atcbpwm = tcbpwmc->pwms[0];
 
 	/*
-	 * PWM devices provided by TCB driver are grouped by 2:
-	 * - group 0: PWM 0 & 1
-	 * - group 1: PWM 2 & 3
-	 * - group 2: PWM 4 & 5
-	 *
+	 * PWM devices provided by the TCB driver are grouped by 2.
 	 * PWM devices in a given group must be configured with the
 	 * same period_ns.
 	 *
@@ -365,31 +367,40 @@ static const struct pwm_ops atmel_tcb_pwm_ops = {
 
 static int atmel_tcb_pwm_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *match;
 	struct atmel_tcb_pwm_chip *tcbpwm;
 	struct device_node *np = pdev->dev.of_node;
-	struct atmel_tc *tc;
+	struct regmap *regmap;
+	struct clk *clk;
+	struct clk *slow_clk;
 	int err;
-	int tcblock;
+	int channel;
 
-	err = of_property_read_u32(np, "tc-block", &tcblock);
+	err = of_property_read_u32(np, "reg", &channel);
 	if (err < 0) {
 		dev_err(&pdev->dev,
-			"failed to get Timer Counter Block number from device tree (error: %d)\n",
+			"failed to get Timer Counter Block channel from device tree (error: %d)\n",
 			err);
 		return err;
 	}
 
-	tc = atmel_tc_alloc(tcblock);
-	if (tc == NULL) {
-		dev_err(&pdev->dev, "failed to allocate Timer Counter Block\n");
-		return -ENOMEM;
-	}
+	regmap = syscon_node_to_regmap(np->parent);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	slow_clk = of_clk_get_by_name(np->parent, "slow_clk");
+	if (IS_ERR(slow_clk))
+		return PTR_ERR(slow_clk);
+
+	clk = tcb_clk_get(np, channel);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
 
 	tcbpwm = devm_kzalloc(&pdev->dev, sizeof(*tcbpwm), GFP_KERNEL);
 	if (tcbpwm == NULL) {
 		err = -ENOMEM;
 		dev_err(&pdev->dev, "failed to allocate memory\n");
-		goto err_free_tc;
+		goto err_slow_clk;
 	}
 
 	tcbpwm->chip.dev = &pdev->dev;
@@ -398,11 +409,17 @@ static int atmel_tcb_pwm_probe(struct platform_device *pdev)
 	tcbpwm->chip.of_pwm_n_cells = 3;
 	tcbpwm->chip.base = -1;
 	tcbpwm->chip.npwm = NPWM;
-	tcbpwm->tc = tc;
+	tcbpwm->channel = channel;
+	tcbpwm->regmap = regmap;
+	tcbpwm->clk = clk;
+	tcbpwm->slow_clk = slow_clk;
 
-	err = clk_prepare_enable(tc->slow_clk);
+	match = of_match_node(atmel_tcb_dt_ids, np->parent);
+	tcbpwm->width = (int)match->data;
+
+	err = clk_prepare_enable(slow_clk);
 	if (err)
-		goto err_free_tc;
+		goto err_slow_clk;
 
 	spin_lock_init(&tcbpwm->lock);
 
@@ -415,10 +432,10 @@ static int atmel_tcb_pwm_probe(struct platform_device *pdev)
 	return 0;
 
 err_disable_clk:
-	clk_disable_unprepare(tcbpwm->tc->slow_clk);
+	clk_disable_unprepare(tcbpwm->slow_clk);
 
-err_free_tc:
-	atmel_tc_free(tc);
+err_slow_clk:
+	clk_put(slow_clk);
 
 	return err;
 }
@@ -428,14 +445,14 @@ static int atmel_tcb_pwm_remove(struct platform_device *pdev)
 	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
 	int err;
 
-	clk_disable_unprepare(tcbpwm->tc->slow_clk);
+	clk_disable_unprepare(tcbpwm->slow_clk);
+	clk_put(tcbpwm->slow_clk);
+	clk_put(tcbpwm->clk);
 
 	err = pwmchip_remove(&tcbpwm->chip);
 	if (err < 0)
 		return err;
 
-	atmel_tc_free(tcbpwm->tc);
-
 	return 0;
 }
 
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding
  2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
                   ` (46 preceding siblings ...)
  2016-06-10 22:03 ` [PATCH 47/48] PWM: atmel-tcb: switch to new binding Alexandre Belloni
@ 2016-06-10 22:03 ` Alexandre Belloni
  2016-06-11  0:14   ` kbuild test robot
  47 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:03 UTC (permalink / raw)
  To: Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Alexandre Belloni,
	Antoine Aubert

Switch to the new pwm-atmel-tcb binding that avoid wasting TCB channels.

Cc: Antoine Aubert <a.aubert@overkiz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
 arch/arm/boot/dts/at91-kizbox.dts | 42 +++++++++++++++++++++++++--------------
 1 file changed, 27 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 58c5d0d3dd66..6579f955250b 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -43,6 +43,29 @@
 				};
 			};
 
+			tcb1: timer@fffdc000 {
+				tcb1_pwm0: pwm@0 {
+					compatible = "atmel,tcb-pwm";
+					#pwm-cells = <3>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_tcb1_tioa0 &pinctrl_tcb1_tiob0>;
+				}
+
+				tcb1_pwm1: pwm@1 {
+					compatible = "atmel,tcb-pwm";
+					#pwm-cells = <3>;
+					pinctrl-names = "default";
+					pinctrl-0 = &pinctrl_tcb1_tioa1>;
+				}
+
+				tcb1_pwm2: pwm@2 {
+					compatible = "atmel,tcb-pwm";
+					#pwm-cells = <3>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_tcb1_tioa2>;
+				}
+			};
+
 			macb0: ethernet@fffc4000 {
 				phy-mode = "mii";
 				pinctrl-0 = <&pinctrl_macb_rmii
@@ -122,41 +145,30 @@
 
 		network_green {
 			label = "pwm:green:network";
-			pwms = <&tcb_pwm 2 10000000 PWM_POLARITY_INVERTED>;
+			pwms = <&tcb1_pwm1 0 10000000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 
 		network_red {
 			label = "pwm:red:network";
-			pwms = <&tcb_pwm 4 10000000 PWM_POLARITY_INVERTED>;
+			pwms = <&tcb1_pwm2 0 10000000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 
 		user_green {
 			label = "pwm:green:user";
-			pwms = <&tcb_pwm 0 10000000 PWM_POLARITY_INVERTED>;
+			pwms = <&tcb1_pwm0 0 10000000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 
 		user_red {
 			label = "pwm:red:user";
-			pwms = <&tcb_pwm 1 10000000 PWM_POLARITY_INVERTED>;
+			pwms = <&tcb1_pwm0 1 10000000 PWM_POLARITY_INVERTED>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};
 	};
-
-	tcb_pwm: pwm {
-		compatible = "atmel,tcb-pwm";
-		#pwm-cells = <3>;
-		tc-block = <1>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tcb1_tioa0
-			     &pinctrl_tcb1_tioa1
-			     &pinctrl_tcb1_tioa2
-			     &pinctrl_tcb1_tiob0>;
-	};
 };
-- 
2.8.1

^ permalink raw reply related	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
@ 2016-06-10 22:30   ` Arnd Bergmann
  2016-06-10 22:37     ` Alexandre Belloni
  2016-06-13 15:24     ` Alexandre Belloni
  2016-06-11  7:49   ` Boris Brezillon
  1 sibling, 2 replies; 75+ messages in thread
From: Arnd Bergmann @ 2016-06-10 22:30 UTC (permalink / raw)
  To: linux-arm-kernel
  Cc: Alexandre Belloni, Nicolas Ferre, Boris Brezillon, Stephen Boyd,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk

On Saturday, June 11, 2016 12:03:04 AM CEST Alexandre Belloni wrote:
> From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> 
> Fix the main and slow clock .prepare() implementations which used to call
> usleep() when the scheduler wasn't ready yet.
> 

Does this have to be called that early? It seems wasteful to always
call udelay() here, when these are functions that are normally
allowed to sleep.

	Arnd

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-10 22:30   ` Arnd Bergmann
@ 2016-06-10 22:37     ` Alexandre Belloni
  2016-06-13 15:24     ` Alexandre Belloni
  1 sibling, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-10 22:37 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-arm-kernel, Nicolas Ferre, Boris Brezillon, Stephen Boyd,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk

On 11/06/2016 at 00:30:36 +0200, Arnd Bergmann wrote :
> On Saturday, June 11, 2016 12:03:04 AM CEST Alexandre Belloni wrote:
> > From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> > 
> > Fix the main and slow clock .prepare() implementations which used to call
> > usleep() when the scheduler wasn't ready yet.
> > 
> 
> Does this have to be called that early? It seems wasteful to always
> call udelay() here, when these are functions that are normally
> allowed to sleep.
> 

Well, the main issue here is that we want to be able to prepare_enable
the slow clock before we are allowed to sleep.

Thinking about it when writing that, I realize that when I reworked my
series, I removed the dependency between the clocksource TCB and the
slow_clock. But I guess we still have one on the main clock. I'll check
whether this is still necessary.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding
  2016-06-10 22:03 ` [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding Alexandre Belloni
@ 2016-06-11  0:14   ` kbuild test robot
  2016-06-11 10:25     ` Alexandre Belloni
  0 siblings, 1 reply; 75+ messages in thread
From: kbuild test robot @ 2016-06-11  0:14 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: kbuild-all, Nicolas Ferre, Boris Brezillon,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Alexandre Belloni, Antoine Aubert

[-- Attachment #1: Type: text/plain, Size: 1075 bytes --]

Hi,

[auto build test ERROR on at91/at91-next]
[also build test ERROR on v4.7-rc2 next-20160609]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Alexandre-Belloni/ARM-at91-rework-Atmel-TCB-drivers/20160611-062134
base:   https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
config: arm-at91_dt_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 5.3.1-8) 5.3.1 20160205
reproduce:
        wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # save the attached .config to linux build tree
        make.cross ARCH=arm 

All errors (new ones prefixed by >>):

>> Error: arch/arm/boot/dts/at91-kizbox.dts:54.5-15 syntax error
   FATAL ERROR: Unable to parse input tree

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 21096 bytes --]

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 47/48] PWM: atmel-tcb: switch to new binding
  2016-06-10 22:03 ` [PATCH 47/48] PWM: atmel-tcb: switch to new binding Alexandre Belloni
@ 2016-06-11  2:22   ` kbuild test robot
  0 siblings, 0 replies; 75+ messages in thread
From: kbuild test robot @ 2016-06-11  2:22 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: kbuild-all, Nicolas Ferre, Boris Brezillon,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Alexandre Belloni, Thierry Reding, linux-pwm

[-- Attachment #1: Type: text/plain, Size: 1881 bytes --]

Hi,

[auto build test WARNING on at91/at91-next]
[also build test WARNING on v4.7-rc2 next-20160609]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Alexandre-Belloni/ARM-at91-rework-Atmel-TCB-drivers/20160611-062134
base:   https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
config: x86_64-allmodconfig (attached as .config)
compiler: gcc-6 (Debian 6.1.1-1) 6.1.1 20160430
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All warnings (new ones prefixed by >>):

   drivers/pwm/pwm-atmel-tcb.c: In function 'atmel_tcb_pwm_probe':
>> drivers/pwm/pwm-atmel-tcb.c:418:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
     tcbpwm->width = (int)match->data;
                     ^

vim +418 drivers/pwm/pwm-atmel-tcb.c

   402			dev_err(&pdev->dev, "failed to allocate memory\n");
   403			goto err_slow_clk;
   404		}
   405	
   406		tcbpwm->chip.dev = &pdev->dev;
   407		tcbpwm->chip.ops = &atmel_tcb_pwm_ops;
   408		tcbpwm->chip.of_xlate = of_pwm_xlate_with_flags;
   409		tcbpwm->chip.of_pwm_n_cells = 3;
   410		tcbpwm->chip.base = -1;
   411		tcbpwm->chip.npwm = NPWM;
   412		tcbpwm->channel = channel;
   413		tcbpwm->regmap = regmap;
   414		tcbpwm->clk = clk;
   415		tcbpwm->slow_clk = slow_clk;
   416	
   417		match = of_match_node(atmel_tcb_dt_ids, np->parent);
 > 418		tcbpwm->width = (int)match->data;
   419	
   420		err = clk_prepare_enable(slow_clk);
   421		if (err)
   422			goto err_slow_clk;
   423	
   424		spin_lock_init(&tcbpwm->lock);
   425	
   426		err = pwmchip_add(&tcbpwm->chip);

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 54115 bytes --]

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
  2016-06-10 22:30   ` Arnd Bergmann
@ 2016-06-11  7:49   ` Boris Brezillon
  1 sibling, 0 replies; 75+ messages in thread
From: Boris Brezillon @ 2016-06-11  7:49 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Nicolas Ferre, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Cyrille Pitchen, Stephen Boyd,
	linux-clk

On Sat, 11 Jun 2016 00:03:04 +0200
Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:

> From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> 
> Fix the main and slow clock .prepare() implementations which used to call
> usleep() when the scheduler wasn't ready yet.
> 
> Cc: Stephen Boyd <sboyd@codeaurora.org>
> Cc: linux-clk@vger.kernel.org
> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> ---
>  drivers/clk/at91/clk-main.c | 2 +-
>  drivers/clk/at91/clk-slow.c | 6 +++---
>  2 files changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/clk/at91/clk-main.c b/drivers/clk/at91/clk-main.c
> index 58b5baca670c..12c5062aeb92 100644
> --- a/drivers/clk/at91/clk-main.c
> +++ b/drivers/clk/at91/clk-main.c
> @@ -342,7 +342,7 @@ static int clk_main_probe_frequency(struct regmap *regmap)
>  		regmap_read(regmap, AT91_CKGR_MCFR, &mcfr);
>  		if (mcfr & AT91_PMC_MAINRDY)
>  			return 0;
> -		usleep_range(MAINF_LOOP_MIN_WAIT, MAINF_LOOP_MAX_WAIT);
> +		udelay(MAINF_LOOP_MIN_WAIT);
>  	} while (time_before(prep_time, timeout));
>  
>  	return -ETIMEDOUT;
> diff --git a/drivers/clk/at91/clk-slow.c b/drivers/clk/at91/clk-slow.c
> index 61090b1146cf..612e893ce994 100644
> --- a/drivers/clk/at91/clk-slow.c
> +++ b/drivers/clk/at91/clk-slow.c
> @@ -76,7 +76,7 @@ static int clk_slow_osc_prepare(struct clk_hw *hw)
>  
>  	writel(tmp | AT91_SCKC_OSC32EN, sckcr);
>  
> -	usleep_range(osc->startup_usec, osc->startup_usec + 1);
> +	udelay(osc->startup_usec);

If you're using udelay() you should probably move the code in
->prepare() into ->enable(). The same goes for the following changes.

>  
>  	return 0;
>  }
> @@ -195,7 +195,7 @@ static int clk_slow_rc_osc_prepare(struct clk_hw *hw)
>  
>  	writel(readl(sckcr) | AT91_SCKC_RCEN, sckcr);
>  
> -	usleep_range(osc->startup_usec, osc->startup_usec + 1);
> +	udelay(osc->startup_usec);
>  
>  	return 0;
>  }
> @@ -304,7 +304,7 @@ static int clk_sam9x5_slow_set_parent(struct clk_hw *hw, u8 index)
>  
>  	writel(tmp, sckcr);
>  
> -	usleep_range(SLOWCK_SW_TIME_USEC, SLOWCK_SW_TIME_USEC + 1);
> +	udelay(SLOWCK_SW_TIME_USEC);
>  
>  	return 0;
>  }



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-10 22:03 ` [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT Alexandre Belloni
@ 2016-06-11  9:43   ` Thomas Gleixner
  2016-06-11 10:53     ` Alexandre Belloni
  0 siblings, 1 reply; 75+ messages in thread
From: Thomas Gleixner @ 2016-06-11  9:43 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Daniel Lezcano

On Sat, 11 Jun 2016, Alexandre Belloni wrote:

> With the new TCB clocksource driver, atmel platforms are now able to boot
> without the PIT driver. Allow unselecting it.

Yay! Thanks for doing this!

     tglx

 

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding
  2016-06-11  0:14   ` kbuild test robot
@ 2016-06-11 10:25     ` Alexandre Belloni
  0 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-11 10:25 UTC (permalink / raw)
  To: kbuild test robot
  Cc: kbuild-all, Nicolas Ferre, Boris Brezillon,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Antoine Aubert

On 11/06/2016 at 08:14:13 +0800, kbuild test robot wrote :
> Hi,
> 
> [auto build test ERROR on at91/at91-next]
> [also build test ERROR on v4.7-rc2 next-20160609]
> [if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
> 
> url:    https://github.com/0day-ci/linux/commits/Alexandre-Belloni/ARM-at91-rework-Atmel-TCB-drivers/20160611-062134
> base:   https://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91.git at91-next
> config: arm-at91_dt_defconfig (attached as .config)
> compiler: arm-linux-gnueabi-gcc (Debian 5.3.1-8) 5.3.1 20160205
> reproduce:
>         wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
>         chmod +x ~/bin/make.cross
>         # save the attached .config to linux build tree
>         make.cross ARCH=arm 
> 
> All errors (new ones prefixed by >>):
> 
> >> Error: arch/arm/boot/dts/at91-kizbox.dts:54.5-15 syntax error
>    FATAL ERROR: Unable to parse input tree
> 

Ok, I'm not sure what happened, this is now fixed in my branch.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-11  9:43   ` Thomas Gleixner
@ 2016-06-11 10:53     ` Alexandre Belloni
  2016-06-13 19:04       ` Boris Brezillon
  0 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-11 10:53 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Daniel Lezcano

On 11/06/2016 at 11:43:54 +0200, Thomas Gleixner wrote :
> On Sat, 11 Jun 2016, Alexandre Belloni wrote:
> 
> > With the new TCB clocksource driver, atmel platforms are now able to boot
> > without the PIT driver. Allow unselecting it.
> 
> Yay! Thanks for doing this!
> 

Sure! Can you still check the request_irq/free_irq in
timer-atmel-tcbclksrc? I'm not sure whether this can work reliably or
only because we are before SYSTEM_STATE=RUNNING.
In the latter case, I have another way of doing that.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-10 22:03 ` [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks Alexandre Belloni
@ 2016-06-11 12:48   ` Boris Brezillon
  2016-06-22 13:07     ` Daniel Lezcano
  2016-06-24 10:07   ` Daniel Lezcano
  1 sibling, 1 reply; 75+ messages in thread
From: Boris Brezillon @ 2016-06-11 12:48 UTC (permalink / raw)
  To: Alexandre Belloni, Daniel Lezcano, Thomas Gleixner
  Cc: Nicolas Ferre, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel

On Sat, 11 Jun 2016 00:03:45 +0200
Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:

> Add a driver for the Atmel Timer Counter Blocks. This driver provides a
> clocksource and a clockevent device. The clockevent device is linked to the
> clocksource counter and so it will run at the same frequency.
> 
> This driver uses regmap and syscon to be able to probe early in the boot
> and avoid having to switch on the TCB clocksource later. Using regmap also
> means that unused TCB channels may be used by other drivers (PWM for
> example).

First of all, thanks for working on this
tcb/libtcb/tcb-clksource/tcb-pwm mess. It looks a lot cleaner after
your changes (both the DT representation and the code itself).

> 
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Thomas Gleixner <tglx@linutronix.de>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> ---
>  drivers/clocksource/Kconfig                 |  13 ++
>  drivers/clocksource/Makefile                |   3 +-
>  drivers/clocksource/timer-atmel-tcbclksrc.c | 305 ++++++++++++++++++++++++++++
>  include/soc/at91/atmel_tcb.h                | 220 ++++++++++++++++++++

I think the creation of atmel_tcb.h should be done in a separate commit.

>  4 files changed, 540 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/clocksource/timer-atmel-tcbclksrc.c
>  create mode 100644 include/soc/at91/atmel_tcb.h
> 
> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> index 47352d25c15e..ff7f4022c749 100644
> --- a/drivers/clocksource/Kconfig
> +++ b/drivers/clocksource/Kconfig
> @@ -258,6 +258,19 @@ config ATMEL_ST
>  	select CLKSRC_OF
>  	select MFD_SYSCON
>  
> +config ATMEL_ARM_TCB_CLKSRC
> +	bool "TC Block Clocksource"
> +	select REGMAP_MMIO
> +	depends on GENERIC_CLOCKEVENTS
> +	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> +	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> +	help
> +	  Select this to get a high precision clocksource based on a
> +	  TC block with a 5+ MHz base clock rate.
> +	  On platforms with 16-bit counters, two timer channels are combined
> +	  to make a single 32-bit timer.
> +	  It can also be used as a clock event device supporting oneshot mode.
> +
>  config CLKSRC_METAG_GENERIC
>  	def_bool y if METAG
>  	help
> diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
> index 473974f9590a..988f33de5808 100644
> --- a/drivers/clocksource/Makefile
> +++ b/drivers/clocksource/Makefile
> @@ -1,7 +1,8 @@
>  obj-$(CONFIG_CLKSRC_PROBE)	+= clksrc-probe.o
>  obj-$(CONFIG_ATMEL_PIT)		+= timer-atmel-pit.o
>  obj-$(CONFIG_ATMEL_ST)		+= timer-atmel-st.o
> -obj-$(CONFIG_ATMEL_TCB_CLKSRC)	+= tcb_clksrc.o
> +obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
> +obj-$(CONFIG_ATMEL_ARM_TCB_CLKSRC)	+= timer-atmel-tcbclksrc.o
>  obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
>  obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o
>  obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC)	+= cs5535-clockevt.o
> diff --git a/drivers/clocksource/timer-atmel-tcbclksrc.c b/drivers/clocksource/timer-atmel-tcbclksrc.c
> new file mode 100644
> index 000000000000..af0b1aab7a98
> --- /dev/null
> +++ b/drivers/clocksource/timer-atmel-tcbclksrc.c
> @@ -0,0 +1,305 @@
> +#include <linux/clk.h>
> +#include <linux/clockchips.h>
> +#include <linux/clocksource.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of_irq.h>
> +#include <linux/regmap.h>
> +#include <linux/sched_clock.h>
> +#include <soc/at91/atmel_tcb.h>
> +
> +struct atmel_tcb_clksrc {
> +	struct clocksource clksrc;
> +	struct clock_event_device clkevt;
> +	struct regmap *regmap;
> +	struct clk *clk[2];
> +	int channels[2];
> +	u8 bits;
> +	unsigned int irq;
> +	bool registered;
> +	bool irq_requested;
> +};
> +
> +static struct atmel_tcb_clksrc tc = {
> +	.clksrc = {
> +		.name		= "tcb_clksrc",
> +		.rating		= 200,
> +		.mask		= CLOCKSOURCE_MASK(32),
> +		.flags		= CLOCK_SOURCE_IS_CONTINUOUS,

			^ 2 tabs here

> +	},
> +	.clkevt	= {
> +		.name			= "tcb_clkevt",

			^ 3 here

Can you make that consistent?
Actually, I'm not a big fan of those tabs, but if you decide to use
tabs, use the same number of them everywhere.

> +		.features		= CLOCK_EVT_FEAT_ONESHOT,
> +		/* Should be lower than at91rm9200's system timer */
> +		.rating			= 125,
> +	},
> +};
> +

[...]

> +
> +static int tcb_clkevt_next_event(unsigned long delta,
> +				 struct clock_event_device *d)
> +{
> +	u32 val;
> +
> +	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
> +	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), val + delta);
> +	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]), ATMEL_TC_CPCS);

Hm, not sure this is 100% sure. What happens if by the time you write
TC_RC, the delta value has expired? This means you'll have to wait
another round before the TC engine generates the "RC reached" interrupt.

I know this is very unlikely, but should we take the risk?

The core seems to check the ->set_next_event() return value and tries to
adjust ->min_delta_ns if it returns an error, so maybe it's worth
testing if val + delta has already occurred just before enabling the
TC_CPCS interrupt, and if it's the case, return an -ETIME error.

Something like:

	u32 val[2], next;

	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[0]);
	next = (val[0] + delta) & GENMASK(tc.bits - 1, 0);
	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), next);
	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[1]);

	if ((next < val[0] && val[1] < val[0] && val[1] >= next) ||
	    (next > val[0] && (val[1] < val[0] || val[1] >= next))) {
		/*
		 * Clear the CPCS bit in the status register to avoid
		 * generating a spurious interrupt next time a valid
		 * timer event is configured.
		 * FIXME: not sure it's safe, since it also clears the
		 * overflow status, but it seems this flag is not used
		 * by the driver anyway.
		 */
		regmap_read(tc.regmap, ATMEL_TC_SR, &val[0]);
		return -ETIME;
	}

	
	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]),
		     ATMEL_TC_CPCS);

Thomas, Daniel, what's your opinion? 

> +
> +	return 0;
> +}
> +


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-10 22:30   ` Arnd Bergmann
  2016-06-10 22:37     ` Alexandre Belloni
@ 2016-06-13 15:24     ` Alexandre Belloni
  2016-06-13 19:26       ` Arnd Bergmann
  2016-06-14 16:05       ` Afzal Mohammed
  1 sibling, 2 replies; 75+ messages in thread
From: Alexandre Belloni @ 2016-06-13 15:24 UTC (permalink / raw)
  To: Arnd Bergmann
  Cc: linux-arm-kernel, Nicolas Ferre, Boris Brezillon, Stephen Boyd,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk

On 11/06/2016 at 00:30:36 +0200, Arnd Bergmann wrote :
> On Saturday, June 11, 2016 12:03:04 AM CEST Alexandre Belloni wrote:
> > From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> > 
> > Fix the main and slow clock .prepare() implementations which used to call
> > usleep() when the scheduler wasn't ready yet.
> > 
> 
> Does this have to be called that early? It seems wasteful to always
> call udelay() here, when these are functions that are normally
> allowed to sleep.
> 

So I've tested it and something like that would work:

	if (system_state < SYSTEM_RUNNING)
		udelay(osc->startup_usec);
	else
		usleep_range(osc->startup_usec, osc->startup_usec + 1);

But I'm afraid it would be the first driver to actually do something
like that (however, it is already the only driver trying to sleep). 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-11 10:53     ` Alexandre Belloni
@ 2016-06-13 19:04       ` Boris Brezillon
  2016-06-13 19:14         ` Thomas Gleixner
  0 siblings, 1 reply; 75+ messages in thread
From: Boris Brezillon @ 2016-06-13 19:04 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Thomas Gleixner, Nicolas Ferre, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Daniel Lezcano

On Sat, 11 Jun 2016 12:53:51 +0200
Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:

> On 11/06/2016 at 11:43:54 +0200, Thomas Gleixner wrote :
> > On Sat, 11 Jun 2016, Alexandre Belloni wrote:
> >   
> > > With the new TCB clocksource driver, atmel platforms are now able to boot
> > > without the PIT driver. Allow unselecting it.  
> > 
> > Yay! Thanks for doing this!
> >   
> 
> Sure! Can you still check the request_irq/free_irq in
> timer-atmel-tcbclksrc? I'm not sure whether this can work reliably or
> only because we are before SYSTEM_STATE=RUNNING.
> In the latter case, I have another way of doing that.
> 

Sorry to put it back on the table, but shouldn't we consider adding
these irq_disable/enable_action() helpers?

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-13 19:04       ` Boris Brezillon
@ 2016-06-13 19:14         ` Thomas Gleixner
  2016-06-16 14:41           ` Boris Brezillon
  0 siblings, 1 reply; 75+ messages in thread
From: Thomas Gleixner @ 2016-06-13 19:14 UTC (permalink / raw)
  To: Boris Brezillon
  Cc: Alexandre Belloni, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Daniel Lezcano

On Mon, 13 Jun 2016, Boris Brezillon wrote:
> On Sat, 11 Jun 2016 12:53:51 +0200
> Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:
> 
> > On 11/06/2016 at 11:43:54 +0200, Thomas Gleixner wrote :
> > > On Sat, 11 Jun 2016, Alexandre Belloni wrote:
> > >   
> > > > With the new TCB clocksource driver, atmel platforms are now able to boot
> > > > without the PIT driver. Allow unselecting it.  
> > > 
> > > Yay! Thanks for doing this!
> > >   
> > 
> > Sure! Can you still check the request_irq/free_irq in
> > timer-atmel-tcbclksrc? I'm not sure whether this can work reliably or
> > only because we are before SYSTEM_STATE=RUNNING.
> > In the latter case, I have another way of doing that.
> > 
> 
> Sorry to put it back on the table, but shouldn't we consider adding
> these irq_disable/enable_action() helpers?

I fear that's the only reliable way to do it.

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-13 15:24     ` Alexandre Belloni
@ 2016-06-13 19:26       ` Arnd Bergmann
  2016-06-14 16:05       ` Afzal Mohammed
  1 sibling, 0 replies; 75+ messages in thread
From: Arnd Bergmann @ 2016-06-13 19:26 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: linux-arm-kernel, Nicolas Ferre, Boris Brezillon, Stephen Boyd,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk

On Monday, June 13, 2016 5:24:09 PM CEST Alexandre Belloni wrote:
> On 11/06/2016 at 00:30:36 +0200, Arnd Bergmann wrote :
> > On Saturday, June 11, 2016 12:03:04 AM CEST Alexandre Belloni wrote:
> > > From: Cyrille Pitchen <cyrille.pitchen@atmel.com>
> > > 
> > > Fix the main and slow clock .prepare() implementations which used to call
> > > usleep() when the scheduler wasn't ready yet.
> > > 
> > 
> > Does this have to be called that early? It seems wasteful to always
> > call udelay() here, when these are functions that are normally
> > allowed to sleep.
> > 
> 
> So I've tested it and something like that would work:
> 
>         if (system_state < SYSTEM_RUNNING)
>                 udelay(osc->startup_usec);
>         else
>                 usleep_range(osc->startup_usec, osc->startup_usec + 1);

I think that's reasonable in this case.

> But I'm afraid it would be the first driver to actually do something
> like that (however, it is already the only driver trying to sleep). 

We have a lot of drivers that call potentially sleeping function from
the .prepare callback, e.g. when they go to an i2c controller.

	Arnd

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-13 15:24     ` Alexandre Belloni
  2016-06-13 19:26       ` Arnd Bergmann
@ 2016-06-14 16:05       ` Afzal Mohammed
  2016-06-14 16:18         ` Boris Brezillon
  1 sibling, 1 reply; 75+ messages in thread
From: Afzal Mohammed @ 2016-06-14 16:05 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Arnd Bergmann, Boris Brezillon, Stephen Boyd, Nicolas Ferre,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk, linux-arm-kernel

Hi,

On Mon, Jun 13, 2016 at 05:24:09PM +0200, Alexandre Belloni wrote:
> On 11/06/2016 at 00:30:36 +0200, Arnd Bergmann wrote :

> > Does this have to be called that early? It seems wasteful to always
> > call udelay() here, when these are functions that are normally
> > allowed to sleep.

> So I've tested it and something like that would work:
> 
> 	if (system_state < SYSTEM_RUNNING)
> 		udelay(osc->startup_usec);
> 	else
> 		usleep_range(osc->startup_usec, osc->startup_usec + 1);
> 
> But I'm afraid it would be the first driver to actually do something
> like that (however, it is already the only driver trying to sleep). 

tglx has suggested to modify clock core to handle a somewhat similar
kind of scenario (probably should work here too) and avoid driver
changes,

http://lkml.kernel.org/r/alpine.DEB.2.11.1606061448010.28031@nanos

Regards
afzal

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 01/48] clk: at91: replace usleep() by udelay() calls
  2016-06-14 16:05       ` Afzal Mohammed
@ 2016-06-14 16:18         ` Boris Brezillon
  0 siblings, 0 replies; 75+ messages in thread
From: Boris Brezillon @ 2016-06-14 16:18 UTC (permalink / raw)
  To: Afzal Mohammed
  Cc: Alexandre Belloni, Arnd Bergmann, Stephen Boyd, Nicolas Ferre,
	linux-kernel, Cyrille Pitchen, Jean-Christophe Plagniol-Villard,
	linux-clk, linux-arm-kernel

On Tue, 14 Jun 2016 21:35:17 +0530
Afzal Mohammed <afzal.mohd.ma@gmail.com> wrote:

> Hi,
> 
> On Mon, Jun 13, 2016 at 05:24:09PM +0200, Alexandre Belloni wrote:
> > On 11/06/2016 at 00:30:36 +0200, Arnd Bergmann wrote :  
> 
> > > Does this have to be called that early? It seems wasteful to always
> > > call udelay() here, when these are functions that are normally
> > > allowed to sleep.  
> 
> > So I've tested it and something like that would work:
> > 
> > 	if (system_state < SYSTEM_RUNNING)
> > 		udelay(osc->startup_usec);
> > 	else
> > 		usleep_range(osc->startup_usec, osc->startup_usec + 1);
> > 
> > But I'm afraid it would be the first driver to actually do something
> > like that (however, it is already the only driver trying to sleep).   
> 
> tglx has suggested to modify clock core to handle a somewhat similar
> kind of scenario (probably should work here too) and avoid driver
> changes,
> 
> http://lkml.kernel.org/r/alpine.DEB.2.11.1606061448010.28031@nanos

Oh, interesting. Definitely a better solution than this custom check.


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 02/48] ARM: at91: Document new TCB bindings
  2016-06-10 22:03 ` [PATCH 02/48] ARM: at91: Document new TCB bindings Alexandre Belloni
@ 2016-06-14 21:47   ` Rob Herring
  2016-06-15  7:29     ` Boris Brezillon
  0 siblings, 1 reply; 75+ messages in thread
From: Rob Herring @ 2016-06-14 21:47 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Daniel Lezcano, Thierry Reding,
	linux-pwm, devicetree

On Sat, Jun 11, 2016 at 12:03:05AM +0200, Alexandre Belloni wrote:
> The current binding for the TCB is not flexible enough for some use cases
> and prevents proper utilization of all the channels.
> 
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: linux-pwm@vger.kernel.org
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> ---
>  .../devicetree/bindings/arm/atmel-at91.txt         | 32 -----------
>  .../devicetree/bindings/mfd/atmel-tcb.txt          | 62 ++++++++++++++++++++++
>  .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      | 12 +++--
>  3 files changed, 69 insertions(+), 37 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt

[...]

> diff --git a/Documentation/devicetree/bindings/mfd/atmel-tcb.txt b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> new file mode 100644
> index 000000000000..48196752c78f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> @@ -0,0 +1,62 @@
> +* Device tree bindings for Atmel Timer Counter Blocks
> +- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon".
> +  <chip> can be "at91rm9200" or "at91sam9x5"
> +- reg: Should contain registers location and length
> +- #address-cells: has to be 1
> +- #size-cells: has to be 0
> +- interrupts: Should contain all interrupts for the TC block
> +  Note that you can specify several interrupt cells if the TC
> +  block has one interrupt per channel.
> +- clock-names: tuple listing input clock names.
> +	Required elements: "t0_clk", "slow_clk"
> +	Optional elements: "t1_clk", "t2_clk"
> +- clocks: phandles to input clocks.

What is the order of clocks?

> +
> +The TCB can expose multiple subdevices:
> + * a clocksource and clockevent device

No. These compatible names are linuxisms. Describe features of the 
timers to be able to select which timer to use if you need to pick 
certain timers. For example, interrupt capability could be used to 
select the clkevt.

> +   - compatible: Should be "atmel,tcb-clksrc"
> +   - reg: Should contain the TCB channels to be used. If the
> +     counter width is 16 bits (at91rm9200-tcb), two consecutive
> +     channels are needed. Else, only one channel will be used.
> +
> + * a clockevent device
> +   - compatible: Should be "atmel,tcb-clkevt"
> +   - reg: Should contain the TCB channel to be used
> +
> + * a PWM chip: see ../pwm/atmel-tcb-pwm.txt
> +
> +Examples:
> +
> +One interrupt per TC block:
> +	tcb0: timer@fff7c000 {
> +		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0xfff7c000 0x100>;
> +		interrupts = <18 4>;
> +		clocks = <&tcb0_clk>;
> +		clock-names = "t0_clk";

Missing slow_clk

> +
> +		timer@0 {
> +			compatible = "atmel,tcb-clksrc";
> +			reg = <0>, <1>;
> +		};
> +
> +		timer@2 {
> +			compatible = "atmel,tcb-clkevt";
> +			reg = <2>;
> +		};
> +	};
> +
> +One interrupt per TC channel in a TC block:
> +	tcb1: timer@fffdc000 {
> +		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0xfffdc000 0x100>;
> +		interrupts = <26 4>, <27 4>, <28 4>;
> +		clocks = <&tcb1_clk>;
> +		clock-names = "t0_clk";
> +	};
> +
> +
> diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> index 8031148bcf85..ab8fbd5ba184 100644
> --- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> @@ -2,15 +2,17 @@ Atmel TCB PWM controller
>  
>  Required properties:
>  - compatible: should be "atmel,tcb-pwm"
> +- reg: tcb channel to use. Each channel can export 2 PWMs

Is there a difference in channels? If not, then this compatible should 
go.

>  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
>    the cells format. The only third cell flag supported by this binding is
>    PWM_POLARITY_INVERTED.
> -- tc-block: The Timer Counter block to use as a PWM chip.
>  
>  Example:
>  
> -pwm {
> -	compatible = "atmel,tcb-pwm";
> -	#pwm-cells = <3>;
> -	tc-block = <1>;
> +tcb0: timer@f800c000 {
> +	pwm@0 {
> +		compatible = "atmel,tcb-pwm";
> +		reg = <0>;
> +		#pwm-cells = <3>;
> +	};
>  };
> -- 
> 2.8.1
> 

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 02/48] ARM: at91: Document new TCB bindings
  2016-06-14 21:47   ` Rob Herring
@ 2016-06-15  7:29     ` Boris Brezillon
  2016-06-21 20:08       ` Rob Herring
  2016-06-21 20:28       ` Rob Herring
  0 siblings, 2 replies; 75+ messages in thread
From: Boris Brezillon @ 2016-06-15  7:29 UTC (permalink / raw)
  To: Rob Herring
  Cc: Alexandre Belloni, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Daniel Lezcano, Thierry Reding, linux-pwm, devicetree

On Tue, 14 Jun 2016 16:47:37 -0500
Rob Herring <robh@kernel.org> wrote:

> On Sat, Jun 11, 2016 at 12:03:05AM +0200, Alexandre Belloni wrote:
> > The current binding for the TCB is not flexible enough for some use cases
> > and prevents proper utilization of all the channels.
> > 
> > Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: linux-pwm@vger.kernel.org
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: devicetree@vger.kernel.org
> > Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> > ---
> >  .../devicetree/bindings/arm/atmel-at91.txt         | 32 -----------
> >  .../devicetree/bindings/mfd/atmel-tcb.txt          | 62 ++++++++++++++++++++++
> >  .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      | 12 +++--
> >  3 files changed, 69 insertions(+), 37 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt  
> 
> [...]
> 
> > diff --git a/Documentation/devicetree/bindings/mfd/atmel-tcb.txt b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> > new file mode 100644
> > index 000000000000..48196752c78f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> > @@ -0,0 +1,62 @@
> > +* Device tree bindings for Atmel Timer Counter Blocks
> > +- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon".
> > +  <chip> can be "at91rm9200" or "at91sam9x5"
> > +- reg: Should contain registers location and length
> > +- #address-cells: has to be 1
> > +- #size-cells: has to be 0
> > +- interrupts: Should contain all interrupts for the TC block
> > +  Note that you can specify several interrupt cells if the TC
> > +  block has one interrupt per channel.
> > +- clock-names: tuple listing input clock names.
> > +	Required elements: "t0_clk", "slow_clk"
> > +	Optional elements: "t1_clk", "t2_clk"
> > +- clocks: phandles to input clocks.  
> 
> What is the order of clocks?
> 
> > +
> > +The TCB can expose multiple subdevices:
> > + * a clocksource and clockevent device  
> 
> No. These compatible names are linuxisms. Describe features of the 
> timers to be able to select which timer to use if you need to pick 
> certain timers. For example, interrupt capability could be used to 
> select the clkevt.

Would 'atmel,tcb-free-running-timer' (to replace 'atmel,tcb-clksrc') and
'atmel,tcb-programmable-timer' (to replace 'atmel,tcb-clkevt') be
acceptable?

> 
> > +   - compatible: Should be "atmel,tcb-clksrc"
> > +   - reg: Should contain the TCB channels to be used. If the
> > +     counter width is 16 bits (at91rm9200-tcb), two consecutive
> > +     channels are needed. Else, only one channel will be used.
> > +
> > + * a clockevent device
> > +   - compatible: Should be "atmel,tcb-clkevt"
> > +   - reg: Should contain the TCB channel to be used
> > +
> > + * a PWM chip: see ../pwm/atmel-tcb-pwm.txt
> > +
> > +Examples:
> > +
> > +One interrupt per TC block:
> > +	tcb0: timer@fff7c000 {
> > +		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		reg = <0xfff7c000 0x100>;
> > +		interrupts = <18 4>;
> > +		clocks = <&tcb0_clk>;
> > +		clock-names = "t0_clk";  
> 
> Missing slow_clk
> 
> > +
> > +		timer@0 {
> > +			compatible = "atmel,tcb-clksrc";
> > +			reg = <0>, <1>;
> > +		};
> > +
> > +		timer@2 {
> > +			compatible = "atmel,tcb-clkevt";
> > +			reg = <2>;
> > +		};
> > +	};
> > +
> > +One interrupt per TC channel in a TC block:
> > +	tcb1: timer@fffdc000 {
> > +		compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		reg = <0xfffdc000 0x100>;
> > +		interrupts = <26 4>, <27 4>, <28 4>;
> > +		clocks = <&tcb1_clk>;
> > +		clock-names = "t0_clk";
> > +	};
> > +
> > +
> > diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > index 8031148bcf85..ab8fbd5ba184 100644
> > --- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > @@ -2,15 +2,17 @@ Atmel TCB PWM controller
> >  
> >  Required properties:
> >  - compatible: should be "atmel,tcb-pwm"
> > +- reg: tcb channel to use. Each channel can export 2 PWMs  
> 
> Is there a difference in channels? If not, then this compatible should 
> go.

This one I don't understand.
The TCB (Timer Counter Block) is an MFD containing 3 Timer Counter
devices. Each of these devices (also called channels) can be assigned a
specific mode:
- timer mode (free-running of programmable)
- waveform generator mode (IOW, a PWM)
- capture mode (an IIO device, but we don't have any driver for that
  right now)

So each sub-device of the TCB is represented as a sub-node with its own
compatible. Is there a problem with that?

> 
> >  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
> >    the cells format. The only third cell flag supported by this binding is
> >    PWM_POLARITY_INVERTED.
> > -- tc-block: The Timer Counter block to use as a PWM chip.
> >  
> >  Example:
> >  
> > -pwm {
> > -	compatible = "atmel,tcb-pwm";
> > -	#pwm-cells = <3>;
> > -	tc-block = <1>;
> > +tcb0: timer@f800c000 {
> > +	pwm@0 {
> > +		compatible = "atmel,tcb-pwm";
> > +		reg = <0>;
> > +		#pwm-cells = <3>;
> > +	};
> >  };
> > -- 
> > 2.8.1
> >   



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT
  2016-06-13 19:14         ` Thomas Gleixner
@ 2016-06-16 14:41           ` Boris Brezillon
  0 siblings, 0 replies; 75+ messages in thread
From: Boris Brezillon @ 2016-06-16 14:41 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Alexandre Belloni, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Daniel Lezcano

Hi Thomas,

On Mon, 13 Jun 2016 21:14:47 +0200 (CEST)
Thomas Gleixner <tglx@linutronix.de> wrote:

> On Mon, 13 Jun 2016, Boris Brezillon wrote:
> > On Sat, 11 Jun 2016 12:53:51 +0200
> > Alexandre Belloni <alexandre.belloni@free-electrons.com> wrote:
> >   
> > > On 11/06/2016 at 11:43:54 +0200, Thomas Gleixner wrote :  
> > > > On Sat, 11 Jun 2016, Alexandre Belloni wrote:
> > > >     
> > > > > With the new TCB clocksource driver, atmel platforms are now able to boot
> > > > > without the PIT driver. Allow unselecting it.    
> > > > 
> > > > Yay! Thanks for doing this!
> > > >     
> > > 
> > > Sure! Can you still check the request_irq/free_irq in
> > > timer-atmel-tcbclksrc? I'm not sure whether this can work reliably or
> > > only because we are before SYSTEM_STATE=RUNNING.
> > > In the latter case, I have another way of doing that.
> > >   
> > 
> > Sorry to put it back on the table, but shouldn't we consider adding
> > these irq_disable/enable_action() helpers?  
> 
> I fear that's the only reliable way to do it.

Alexandre told me you had a better implementation (or idea, I don't
remember) than what was proposed here [1].
Do you plan to submit something, or should we work on it?

Regards,

Boris

[1]https://lkml.org/lkml/2015/8/3/330

-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 02/48] ARM: at91: Document new TCB bindings
  2016-06-15  7:29     ` Boris Brezillon
@ 2016-06-21 20:08       ` Rob Herring
  2016-06-21 20:28       ` Rob Herring
  1 sibling, 0 replies; 75+ messages in thread
From: Rob Herring @ 2016-06-21 20:08 UTC (permalink / raw)
  To: Boris Brezillon
  Cc: Alexandre Belloni, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Daniel Lezcano, Thierry Reding, linux-pwm, devicetree

On Wed, Jun 15, 2016 at 09:29:55AM +0200, Boris Brezillon wrote:
> On Tue, 14 Jun 2016 16:47:37 -0500
> Rob Herring <robh@kernel.org> wrote:
> 
> > On Sat, Jun 11, 2016 at 12:03:05AM +0200, Alexandre Belloni wrote:
> > > The current binding for the TCB is not flexible enough for some use cases
> > > and prevents proper utilization of all the channels.
> > > 
> > > Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > Cc: linux-pwm@vger.kernel.org
> > > Cc: Rob Herring <robh+dt@kernel.org>
> > > Cc: devicetree@vger.kernel.org
> > > Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> > > ---
> > >  .../devicetree/bindings/arm/atmel-at91.txt         | 32 -----------
> > >  .../devicetree/bindings/mfd/atmel-tcb.txt          | 62 ++++++++++++++++++++++
> > >  .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      | 12 +++--
> > >  3 files changed, 69 insertions(+), 37 deletions(-)
> > >  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt  
> > 
> > [...]
> > 
> > > diff --git a/Documentation/devicetree/bindings/mfd/atmel-tcb.txt b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> > > new file mode 100644
> > > index 000000000000..48196752c78f
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/mfd/atmel-tcb.txt
> > > @@ -0,0 +1,62 @@
> > > +* Device tree bindings for Atmel Timer Counter Blocks
> > > +- compatible: Should be "atmel,<chip>-tcb", "simple-mfd", "syscon".
> > > +  <chip> can be "at91rm9200" or "at91sam9x5"
> > > +- reg: Should contain registers location and length
> > > +- #address-cells: has to be 1
> > > +- #size-cells: has to be 0
> > > +- interrupts: Should contain all interrupts for the TC block
> > > +  Note that you can specify several interrupt cells if the TC
> > > +  block has one interrupt per channel.
> > > +- clock-names: tuple listing input clock names.
> > > +	Required elements: "t0_clk", "slow_clk"
> > > +	Optional elements: "t1_clk", "t2_clk"
> > > +- clocks: phandles to input clocks.  
> > 
> > What is the order of clocks?
> > 
> > > +
> > > +The TCB can expose multiple subdevices:
> > > + * a clocksource and clockevent device  
> > 
> > No. These compatible names are linuxisms. Describe features of the 
> > timers to be able to select which timer to use if you need to pick 
> > certain timers. For example, interrupt capability could be used to 
> > select the clkevt.
> 
> Would 'atmel,tcb-free-running-timer' (to replace 'atmel,tcb-clksrc') and
> 'atmel,tcb-programmable-timer' (to replace 'atmel,tcb-clkevt') be
> acceptable?

If that somehow matches the documentation or accurately describes the 
h/w capabilities for them, then yes.

Rob

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 02/48] ARM: at91: Document new TCB bindings
  2016-06-15  7:29     ` Boris Brezillon
  2016-06-21 20:08       ` Rob Herring
@ 2016-06-21 20:28       ` Rob Herring
  1 sibling, 0 replies; 75+ messages in thread
From: Rob Herring @ 2016-06-21 20:28 UTC (permalink / raw)
  To: Boris Brezillon
  Cc: Alexandre Belloni, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel,
	Daniel Lezcano, Thierry Reding, linux-pwm, devicetree

On Wed, Jun 15, 2016 at 09:29:55AM +0200, Boris Brezillon wrote:
> On Tue, 14 Jun 2016 16:47:37 -0500
> Rob Herring <robh@kernel.org> wrote:
> 
> > On Sat, Jun 11, 2016 at 12:03:05AM +0200, Alexandre Belloni wrote:
> > > The current binding for the TCB is not flexible enough for some use cases
> > > and prevents proper utilization of all the channels.
> > > 
> > > Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > Cc: linux-pwm@vger.kernel.org
> > > Cc: Rob Herring <robh+dt@kernel.org>
> > > Cc: devicetree@vger.kernel.org
> > > Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> > > ---
> > >  .../devicetree/bindings/arm/atmel-at91.txt         | 32 -----------
> > >  .../devicetree/bindings/mfd/atmel-tcb.txt          | 62 ++++++++++++++++++++++
> > >  .../devicetree/bindings/pwm/atmel-tcb-pwm.txt      | 12 +++--
> > >  3 files changed, 69 insertions(+), 37 deletions(-)
> > >  create mode 100644 Documentation/devicetree/bindings/mfd/atmel-tcb.txt  
> > 
> > [...]


> > > diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > > index 8031148bcf85..ab8fbd5ba184 100644
> > > --- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > > +++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
> > > @@ -2,15 +2,17 @@ Atmel TCB PWM controller
> > >  
> > >  Required properties:
> > >  - compatible: should be "atmel,tcb-pwm"
> > > +- reg: tcb channel to use. Each channel can export 2 PWMs  
> > 
> > Is there a difference in channels? If not, then this compatible should 
> > go.
> 
> This one I don't understand.
> The TCB (Timer Counter Block) is an MFD containing 3 Timer Counter
> devices. Each of these devices (also called channels) can be assigned a
> specific mode:
> - timer mode (free-running of programmable)
> - waveform generator mode (IOW, a PWM)
> - capture mode (an IIO device, but we don't have any driver for that
>   right now)
> 
> So each sub-device of the TCB is represented as a sub-node with its own
> compatible. Is there a problem with that?

Missed this in my first reply. I guess for purposes of referencing pwm 
from other nodes this is okay.

Rob

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-11 12:48   ` Boris Brezillon
@ 2016-06-22 13:07     ` Daniel Lezcano
  2016-06-22 13:13       ` Boris Brezillon
  0 siblings, 1 reply; 75+ messages in thread
From: Daniel Lezcano @ 2016-06-22 13:07 UTC (permalink / raw)
  To: Boris Brezillon, Alexandre Belloni, Thomas Gleixner
  Cc: Nicolas Ferre, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel

On 06/11/2016 02:48 PM, Boris Brezillon wrote:

[ ... ]

>> +static int tcb_clkevt_next_event(unsigned long delta,
>> +				 struct clock_event_device *d)
>> +{
>> +	u32 val;
>> +
>> +	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
>> +	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), val + delta);
>> +	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]), ATMEL_TC_CPCS);
>
> Hm, not sure this is 100% sure. What happens if by the time you write
> TC_RC, the delta value has expired? This means you'll have to wait
> another round before the TC engine generates the "RC reached" interrupt.
>
> I know this is very unlikely, but should we take the risk?
>
> The core seems to check the ->set_next_event() return value and tries to
> adjust ->min_delta_ns if it returns an error, so maybe it's worth
> testing if val + delta has already occurred just before enabling the
> TC_CPCS interrupt, and if it's the case, return an -ETIME error.
>
> Something like:
>
> 	u32 val[2], next;
>
> 	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[0]);
> 	next = (val[0] + delta) & GENMASK(tc.bits - 1, 0);
> 	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), next);
> 	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[1]);
>
> 	if ((next < val[0] && val[1] < val[0] && val[1] >= next) ||
> 	    (next > val[0] && (val[1] < val[0] || val[1] >= next))) {
> 		/*
> 		 * Clear the CPCS bit in the status register to avoid
> 		 * generating a spurious interrupt next time a valid
> 		 * timer event is configured.
> 		 * FIXME: not sure it's safe, since it also clears the
> 		 * overflow status, but it seems this flag is not used
> 		 * by the driver anyway.
> 		 */
> 		regmap_read(tc.regmap, ATMEL_TC_SR, &val[0]);
> 		return -ETIME;
> 	}
>
> 	
> 	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]),
> 		     ATMEL_TC_CPCS);
>
> Thomas, Daniel, what's your opinion?

Are you describing the same as commit 
f9eccf24615672896dc13251410c3f2f33a14f95 ?


-- 
  <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-22 13:07     ` Daniel Lezcano
@ 2016-06-22 13:13       ` Boris Brezillon
  0 siblings, 0 replies; 75+ messages in thread
From: Boris Brezillon @ 2016-06-22 13:13 UTC (permalink / raw)
  To: Daniel Lezcano
  Cc: Alexandre Belloni, Thomas Gleixner, Nicolas Ferre,
	Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel

On Wed, 22 Jun 2016 15:07:00 +0200
Daniel Lezcano <daniel.lezcano@linaro.org> wrote:

> On 06/11/2016 02:48 PM, Boris Brezillon wrote:
> 
> [ ... ]
> 
> >> +static int tcb_clkevt_next_event(unsigned long delta,
> >> +				 struct clock_event_device *d)
> >> +{
> >> +	u32 val;
> >> +
> >> +	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
> >> +	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), val + delta);
> >> +	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]), ATMEL_TC_CPCS);  
> >
> > Hm, not sure this is 100% sure. What happens if by the time you write
> > TC_RC, the delta value has expired? This means you'll have to wait
> > another round before the TC engine generates the "RC reached" interrupt.
> >
> > I know this is very unlikely, but should we take the risk?
> >
> > The core seems to check the ->set_next_event() return value and tries to
> > adjust ->min_delta_ns if it returns an error, so maybe it's worth
> > testing if val + delta has already occurred just before enabling the
> > TC_CPCS interrupt, and if it's the case, return an -ETIME error.
> >
> > Something like:
> >
> > 	u32 val[2], next;
> >
> > 	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[0]);
> > 	next = (val[0] + delta) & GENMASK(tc.bits - 1, 0);
> > 	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), next);
> > 	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val[1]);
> >
> > 	if ((next < val[0] && val[1] < val[0] && val[1] >= next) ||
> > 	    (next > val[0] && (val[1] < val[0] || val[1] >= next))) {
> > 		/*
> > 		 * Clear the CPCS bit in the status register to avoid
> > 		 * generating a spurious interrupt next time a valid
> > 		 * timer event is configured.
> > 		 * FIXME: not sure it's safe, since it also clears the
> > 		 * overflow status, but it seems this flag is not used
> > 		 * by the driver anyway.
> > 		 */
> > 		regmap_read(tc.regmap, ATMEL_TC_SR, &val[0]);
> > 		return -ETIME;
> > 	}
> >
> > 	
> > 	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]),
> > 		     ATMEL_TC_CPCS);
> >
> > Thomas, Daniel, what's your opinion?  
> 
> Are you describing the same as commit 
> f9eccf24615672896dc13251410c3f2f33a14f95 ?

Pretty much, yes. Note that this is purely hypothetical in the TCB
case, but I fear people might experience this problem if they're trying
to configure tiny delay values.

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-10 22:03 ` [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks Alexandre Belloni
  2016-06-11 12:48   ` Boris Brezillon
@ 2016-06-24 10:07   ` Daniel Lezcano
  2017-05-16 11:59     ` Alexandre Belloni
  1 sibling, 1 reply; 75+ messages in thread
From: Daniel Lezcano @ 2016-06-24 10:07 UTC (permalink / raw)
  To: Alexandre Belloni, Nicolas Ferre
  Cc: Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Thomas Gleixner

On 06/11/2016 12:03 AM, Alexandre Belloni wrote:
> Add a driver for the Atmel Timer Counter Blocks. This driver provides a
> clocksource and a clockevent device. The clockevent device is linked to the
> clocksource counter and so it will run at the same frequency.
>
> This driver uses regmap and syscon to be able to probe early in the boot
> and avoid having to switch on the TCB clocksource later. Using regmap also
> means that unused TCB channels may be used by other drivers (PWM for
> example).
>
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Thomas Gleixner <tglx@linutronix.de>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> ---
>   drivers/clocksource/Kconfig                 |  13 ++
>   drivers/clocksource/Makefile                |   3 +-
>   drivers/clocksource/timer-atmel-tcbclksrc.c | 305 ++++++++++++++++++++++++++++
>   include/soc/at91/atmel_tcb.h                | 220 ++++++++++++++++++++
>   4 files changed, 540 insertions(+), 1 deletion(-)
>   create mode 100644 drivers/clocksource/timer-atmel-tcbclksrc.c
>   create mode 100644 include/soc/at91/atmel_tcb.h
>
> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> index 47352d25c15e..ff7f4022c749 100644
> --- a/drivers/clocksource/Kconfig
> +++ b/drivers/clocksource/Kconfig
> @@ -258,6 +258,19 @@ config ATMEL_ST
>   	select CLKSRC_OF
>   	select MFD_SYSCON
>
> +config ATMEL_ARM_TCB_CLKSRC
> +	bool "TC Block Clocksource"

The Kconfig options are set now with the COMPILE_TEST option in order to 
increase the compilation test coverage.

Please, add bool "TC Block Clocksource" if COMPILE_TEST, ...

> +	select REGMAP_MMIO
> +	depends on GENERIC_CLOCKEVENTS
> +	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> +	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5

... remove these dependencies and let the SoC's Kconfig to select the 
timer like the other timers are.

> +	help
> +	  Select this to get a high precision clocksource based on a
> +	  TC block with a 5+ MHz base clock rate.
> +	  On platforms with 16-bit counters, two timer channels are combined
> +	  to make a single 32-bit timer.
> +	  It can also be used as a clock event device supporting oneshot mode.
> +
>   config CLKSRC_METAG_GENERIC
>   	def_bool y if METAG
>   	help
> diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
> index 473974f9590a..988f33de5808 100644
> --- a/drivers/clocksource/Makefile
> +++ b/drivers/clocksource/Makefile
> @@ -1,7 +1,8 @@
>   obj-$(CONFIG_CLKSRC_PROBE)	+= clksrc-probe.o
>   obj-$(CONFIG_ATMEL_PIT)		+= timer-atmel-pit.o
>   obj-$(CONFIG_ATMEL_ST)		+= timer-atmel-st.o
> -obj-$(CONFIG_ATMEL_TCB_CLKSRC)	+= tcb_clksrc.o
> +obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
> +obj-$(CONFIG_ATMEL_ARM_TCB_CLKSRC)	+= timer-atmel-tcbclksrc.o
>   obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
>   obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o
>   obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC)	+= cs5535-clockevt.o
> diff --git a/drivers/clocksource/timer-atmel-tcbclksrc.c b/drivers/clocksource/timer-atmel-tcbclksrc.c
> new file mode 100644
> index 000000000000..af0b1aab7a98
> --- /dev/null
> +++ b/drivers/clocksource/timer-atmel-tcbclksrc.c
> @@ -0,0 +1,305 @@
> +#include <linux/clk.h>
> +#include <linux/clockchips.h>
> +#include <linux/clocksource.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of_irq.h>
> +#include <linux/regmap.h>
> +#include <linux/sched_clock.h>
> +#include <soc/at91/atmel_tcb.h>
> +
> +struct atmel_tcb_clksrc {
> +	struct clocksource clksrc;
> +	struct clock_event_device clkevt;
> +	struct regmap *regmap;
> +	struct clk *clk[2];
> +	int channels[2];
> +	u8 bits;
> +	unsigned int irq;

The test in the init function checks against < 0 but 'irq' is 'unsigned'

> +	bool registered;
> +	bool irq_requested;
> +};
> +
> +static struct atmel_tcb_clksrc tc = {
> +	.clksrc = {
> +		.name		= "tcb_clksrc",
> +		.rating		= 200,
> +		.mask		= CLOCKSOURCE_MASK(32),
> +		.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
> +	},
> +	.clkevt	= {
> +		.name			= "tcb_clkevt",
> +		.features		= CLOCK_EVT_FEAT_ONESHOT,
> +		/* Should be lower than at91rm9200's system timer */
> +		.rating			= 125,
> +	},
> +};
> +
> +static cycle_t tc_get_cycles(struct clocksource *cs)
> +{
> +	unsigned long	flags;
> +	u32		lower, upper, tmp;
> +
> +	raw_local_irq_save(flags);
> +	do {
> +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &upper);
> +		regmap_read(tc.regmap, ATMEL_TC_CV(0), &lower);
> +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &tmp);
> +	} while (upper != tmp);
> +
> +	raw_local_irq_restore(flags);

Why is this lock needed ?

> +	return (upper << 16) | lower;
> +}
> +
> +static cycle_t tc_get_cycles32(struct clocksource *cs)
> +{
> +	u32 val;
> +
> +	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
> +
> +	return val;
> +}
> +
> +static u64 tc_sched_clock_read(void)
> +{
> +	return tc_get_cycles(&tc.clksrc);
> +}
> +
> +static u64 tc_sched_clock_read32(void)
> +{
> +	return tc_get_cycles32(&tc.clksrc);
> +}

'notrace' should be added here to avoid recursion with ftrace.

> +static int tcb_clkevt_next_event(unsigned long delta,
> +				 struct clock_event_device *d)
> +{
> +	u32 val;
> +
> +	regmap_read(tc.regmap, ATMEL_TC_CV(tc.channels[0]), &val);
> +	regmap_write(tc.regmap, ATMEL_TC_RC(tc.channels[0]), val + delta);
> +	regmap_write(tc.regmap, ATMEL_TC_IER(tc.channels[0]), ATMEL_TC_CPCS);
> +
> +	return 0;
> +}
> +
> +static irqreturn_t tc_clkevt_irq(int irq, void *handle)
> +{
> +	unsigned int sr;
> +
> +	regmap_read(tc.regmap, ATMEL_TC_SR(tc.channels[0]), &sr);
> +	if (sr & ATMEL_TC_CPCS) {
> +		tc.clkevt.event_handler(&tc.clkevt);
> +		return IRQ_HANDLED;
> +	}
> +
> +	return IRQ_NONE;
> +}
> +
> +static int tcb_clkevt_oneshot(struct clock_event_device *dev)
> +{
> +	int ret;
> +
> +	if (tc.irq_requested)
> +		return 0;
> +
> +	ret = request_irq(tc.irq, tc_clkevt_irq, IRQF_TIMER | IRQF_SHARED,
> +			  "tcb_clkevt", &tc);
> +	if (!ret)
> +		tc.irq_requested = true;

The legacy driver checks clockevent_state_detached() and disables the clock.

Why is 'irq_requested' and request_irq/free_irq cleaner ?

Isn't there a configuration with the TCB register to disable the 
clockevent only ?

> +	return ret;
> +}
> +
> +static int tcb_clkevt_shutdown(struct clock_event_device *dev)
> +{
> +	regmap_write(tc.regmap, ATMEL_TC_IDR(tc.channels[0]), 0xff);
> +	if (tc.bits == 16)
> +		regmap_write(tc.regmap, ATMEL_TC_IDR(tc.channels[1]), 0xff);
> +
> +	if (tc.irq_requested) {
> +		free_irq(tc.irq, &tc);
> +		tc.irq_requested = false;
> +	}
> +
> +	return 0;
> +}

[ ... ]

> +static void __init tcb_clksrc_init(struct device_node *node)
> +{
> +	const struct of_device_id *match;
> +	u32 rate, divided_rate = 0;
> +	int best_divisor_idx = -1;
> +	int i, err;
> +
> +	if (tc.registered)
> +		return;

That's getting annoying. It is not your fault but that's a repeating 
pattern when multiple nodes are defined for a timer. Someday we will 
have to sit down and think about that.

> +	tc.regmap = syscon_node_to_regmap(node->parent);
> +	if (IS_ERR(tc.regmap))
> +		return;
> +
> +	match = of_match_node(atmel_tcb_dt_ids, node->parent);
> +	tc.bits = (int)match->data;
> +
> +	err = of_property_read_u32_index(node, "reg", 0, &tc.channels[0]);
> +	if (err)
> +		return;
> +
> +	tc.channels[1] = -1;
> +
> +	if (tc.bits == 16) {
> +		of_property_read_u32_index(node, "reg", 1, &tc.channels[1]);
> +		if (tc.channels[1] == -1) {
> +			pr_err("%s: clocksource needs two channels\n",
> +			       node->parent->full_name);
> +		}
> +	}
> +
> +	tc.irq = tcb_irq_get(node, tc.channels[0]);
> +	if (tc.irq < 0)
> +		return;
> +
> +	tc.clk[0] = tcb_clk_get(node, tc.channels[0]);
> +	if (IS_ERR(tc.clk[0]))
> +		return;
> +	err = clk_prepare_enable(tc.clk[0]);
> +	if (err) {
> +		pr_debug("can't enable T0 clk\n");
> +		goto err_clk;
> +	}
> +
> +	if (tc.bits == 16) {
> +		tc.clk[1] = tcb_clk_get(node, tc.channels[1]);
> +		if (IS_ERR(tc.clk[1]))
> +			goto err_disable_t0;
> +	}
> +
> +	/* How fast will we be counting?  Pick something over 5 MHz.  */
> +	rate = (u32)clk_get_rate(tc.clk[0]);
> +	for (i = 0; i < 5; i++) {
> +		unsigned int divisor = atmel_tc_divisors[i];
> +		unsigned int tmp;
> +
> +		if (!divisor)
> +			continue;
> +
> +		tmp = rate / divisor;
> +		pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
> +		if (best_divisor_idx > 0) {
> +			if (tmp < 5 * 1000 * 1000)
> +				continue;
> +		}
> +		divided_rate = tmp;
> +		best_divisor_idx = i;
> +	}
> +
> +	pr_debug("%s: %s at %d.%03d MHz\n", tc.clksrc.name,
> +		 node->parent->full_name, divided_rate / 1000000,
> +		 ((divided_rate + 500000) % 1000000) / 1000);
> +
> +	if (tc.bits == 32) {
> +		tc.clksrc.read = tc_get_cycles32;
> +		tcb_setup_single_chan(&tc, best_divisor_idx);
> +	} else {
> +		err = clk_prepare_enable(tc.clk[1]);
> +		if (err) {
> +			pr_debug("can't enable T1 clk\n");
> +			goto err_clk1;
> +		}
> +		tc.clksrc.read = tc_get_cycles,
> +		tcb_setup_dual_chan(&tc, best_divisor_idx);
> +	}
> +
> +	err = clocksource_register_hz(&tc.clksrc, divided_rate);
> +	if (err)
> +		goto err_disable_t1;
> +
> +	if (tc.bits == 32)

Can't you can group the code under tc.bits == 16 and tc.bits == 32 
instead of multiple check against the reg width ?

> +		sched_clock_register(tc_sched_clock_read32, 32, divided_rate);
> +	else
> +		sched_clock_register(tc_sched_clock_read, 32, divided_rate);
> +
> +	tc.registered = true;
> +
> +	/* Set up and register clockevents */
> +	tc.clkevt.cpumask = cpumask_of(0);
> +	tc.clkevt.set_next_event = tcb_clkevt_next_event;
> +	tc.clkevt.set_state_oneshot = tcb_clkevt_oneshot;
> +	tc.clkevt.set_state_shutdown = tcb_clkevt_shutdown;
> +	if (tc.bits == 16)
> +		clockevents_config_and_register(&tc.clkevt, divided_rate, 1,
> +						0xffff);
> +	else
> +		clockevents_config_and_register(&tc.clkevt, divided_rate, 1,
> +						0xffffffff);
> +	return;

clockevents_config_and_register(&tc.clkevt, divided_rate, 1, 
BIT(tc.bits) - 1);

IIRC, there is a macro somewhere doing BIT(n) - 1. CLOCKSOURCE_MASK does 
it but it is weird to set a clockevent with a clocksource mask.

> +
> +err_disable_t1:
> +	if (tc.bits == 16)
> +		clk_disable_unprepare(tc.clk[1]);
> +
> +err_clk1:
> +	if (tc.bits == 16)
> +		clk_put(tc.clk[1]);
> +
> +err_disable_t0:
> +	clk_disable_unprepare(tc.clk[0]);
> +
> +err_clk:
> +	clk_put(tc.clk[0]);
> +
> +	pr_err("%s: unable to register clocksource/clockevent\n",
> +	       tc.clksrc.name);
> +}
> +CLOCKSOURCE_OF_DECLARE(atmel_tcb_clksrc, "atmel,tcb-clksrc",
> +		       tcb_clksrc_init);

[ ... ]


-- 
  <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2016-06-24 10:07   ` Daniel Lezcano
@ 2017-05-16 11:59     ` Alexandre Belloni
  2017-05-16 14:25       ` Daniel Lezcano
  0 siblings, 1 reply; 75+ messages in thread
From: Alexandre Belloni @ 2017-05-16 11:59 UTC (permalink / raw)
  To: Daniel Lezcano
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Thomas Gleixner

Hi Daniel,

Almost one year later, I'm back on that topic.

On 24/06/2016 at 12:07:01 +0200, Daniel Lezcano wrote:
> > diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> > index 47352d25c15e..ff7f4022c749 100644
> > --- a/drivers/clocksource/Kconfig
> > +++ b/drivers/clocksource/Kconfig
> > @@ -258,6 +258,19 @@ config ATMEL_ST
> >   	select CLKSRC_OF
> >   	select MFD_SYSCON
> > 
> > +config ATMEL_ARM_TCB_CLKSRC
> > +	bool "TC Block Clocksource"
> 
> The Kconfig options are set now with the COMPILE_TEST option in order to
> increase the compilation test coverage.
> 
> Please, add bool "TC Block Clocksource" if COMPILE_TEST, ...
> 
> > +	select REGMAP_MMIO
> > +	depends on GENERIC_CLOCKEVENTS
> > +	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> > +	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> 
> ... remove these dependencies and let the SoC's Kconfig to select the timer
> like the other timers are.
> 

The main issue with what you suggest is that it removes the possibility
to not compile the driver. This may be interesting for people using the
PIT as the clocksource/clockevent and the TCBs for something else.

> > +static cycle_t tc_get_cycles(struct clocksource *cs)
> > +{
> > +	unsigned long	flags;
> > +	u32		lower, upper, tmp;
> > +
> > +	raw_local_irq_save(flags);
> > +	do {
> > +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &upper);
> > +		regmap_read(tc.regmap, ATMEL_TC_CV(0), &lower);
> > +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &tmp);
> > +	} while (upper != tmp);
> > +
> > +	raw_local_irq_restore(flags);
> 
> Why is this lock needed ?
> 

I've taken that from the old driver, I'm not sure this is needed. Maybe
to lower the chance to have upper != tmp.

> > +	return (upper << 16) | lower;
> > +}
> > +


> > +static int tcb_clkevt_oneshot(struct clock_event_device *dev)
> > +{
> > +	int ret;
> > +
> > +	if (tc.irq_requested)
> > +		return 0;
> > +
> > +	ret = request_irq(tc.irq, tc_clkevt_irq, IRQF_TIMER | IRQF_SHARED,
> > +			  "tcb_clkevt", &tc);
> > +	if (!ret)
> > +		tc.irq_requested = true;
> 
> The legacy driver checks clockevent_state_detached() and disables the clock.
> 

This feature is different from the legacy driver. Here, the driver is
using a single TCB channel for both clocksource and clockevent while the
legacy driver always uses at least two channels.

> Why is 'irq_requested' and request_irq/free_irq cleaner ?
> 
> Isn't there a configuration with the TCB register to disable the clockevent
> only ?
> 

I'll try something cleaner anyway.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2017-05-16 11:59     ` Alexandre Belloni
@ 2017-05-16 14:25       ` Daniel Lezcano
  2017-05-16 14:35         ` Alexandre Belloni
  0 siblings, 1 reply; 75+ messages in thread
From: Daniel Lezcano @ 2017-05-16 14:25 UTC (permalink / raw)
  To: Alexandre Belloni
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Thomas Gleixner

On 16/05/2017 13:59, Alexandre Belloni wrote:
> Hi Daniel,
> 
> Almost one year later, I'm back on that topic.
> 
> On 24/06/2016 at 12:07:01 +0200, Daniel Lezcano wrote:
>>> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
>>> index 47352d25c15e..ff7f4022c749 100644
>>> --- a/drivers/clocksource/Kconfig
>>> +++ b/drivers/clocksource/Kconfig
>>> @@ -258,6 +258,19 @@ config ATMEL_ST
>>>   	select CLKSRC_OF
>>>   	select MFD_SYSCON
>>>
>>> +config ATMEL_ARM_TCB_CLKSRC
>>> +	bool "TC Block Clocksource"
>>
>> The Kconfig options are set now with the COMPILE_TEST option in order to
>> increase the compilation test coverage.
>>
>> Please, add bool "TC Block Clocksource" if COMPILE_TEST, ...
>>
>>> +	select REGMAP_MMIO
>>> +	depends on GENERIC_CLOCKEVENTS
>>> +	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
>>> +	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
>>
>> ... remove these dependencies and let the SoC's Kconfig to select the timer
>> like the other timers are.
>>
> 
> The main issue with what you suggest is that it removes the possibility
> to not compile the driver. This may be interesting for people using the
> PIT as the clocksource/clockevent and the TCBs for something else.

Is it really a problem? We tend as much as possible to make silent
options in order to let the platform config to select the right clock.


>>> +static cycle_t tc_get_cycles(struct clocksource *cs)
>>> +{
>>> +	unsigned long	flags;
>>> +	u32		lower, upper, tmp;
>>> +
>>> +	raw_local_irq_save(flags);
>>> +	do {
>>> +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &upper);
>>> +		regmap_read(tc.regmap, ATMEL_TC_CV(0), &lower);
>>> +		regmap_read(tc.regmap, ATMEL_TC_CV(1), &tmp);
>>> +	} while (upper != tmp);
>>> +
>>> +	raw_local_irq_restore(flags);
>>
>> Why is this lock needed ?
>>
> 
> I've taken that from the old driver, I'm not sure this is needed. Maybe
> to lower the chance to have upper != tmp.
> 
>>> +	return (upper << 16) | lower;
>>> +}
>>> +

I don't think this is needed.

>>> +static int tcb_clkevt_oneshot(struct clock_event_device *dev)
>>> +{
>>> +	int ret;
>>> +
>>> +	if (tc.irq_requested)
>>> +		return 0;
>>> +
>>> +	ret = request_irq(tc.irq, tc_clkevt_irq, IRQF_TIMER | IRQF_SHARED,
>>> +			  "tcb_clkevt", &tc);
>>> +	if (!ret)
>>> +		tc.irq_requested = true;
>>
>> The legacy driver checks clockevent_state_detached() and disables the clock.
>>
> 
> This feature is different from the legacy driver. Here, the driver is
> using a single TCB channel for both clocksource and clockevent while the
> legacy driver always uses at least two channels.
> 
>> Why is 'irq_requested' and request_irq/free_irq cleaner ?
>>
>> Isn't there a configuration with the TCB register to disable the clockevent
>> only ?
>>
> 
> I'll try something cleaner anyway.

Ok.


-- 
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

^ permalink raw reply	[flat|nested] 75+ messages in thread

* Re: [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks
  2017-05-16 14:25       ` Daniel Lezcano
@ 2017-05-16 14:35         ` Alexandre Belloni
  0 siblings, 0 replies; 75+ messages in thread
From: Alexandre Belloni @ 2017-05-16 14:35 UTC (permalink / raw)
  To: Daniel Lezcano
  Cc: Nicolas Ferre, Boris Brezillon, Jean-Christophe Plagniol-Villard,
	linux-arm-kernel, linux-kernel, Thomas Gleixner

On 16/05/2017 at 16:25:04 +0200, Daniel Lezcano wrote:
> On 16/05/2017 13:59, Alexandre Belloni wrote:
> > Hi Daniel,
> > 
> > Almost one year later, I'm back on that topic.
> > 
> > On 24/06/2016 at 12:07:01 +0200, Daniel Lezcano wrote:
> >>> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> >>> index 47352d25c15e..ff7f4022c749 100644
> >>> --- a/drivers/clocksource/Kconfig
> >>> +++ b/drivers/clocksource/Kconfig
> >>> @@ -258,6 +258,19 @@ config ATMEL_ST
> >>>   	select CLKSRC_OF
> >>>   	select MFD_SYSCON
> >>>
> >>> +config ATMEL_ARM_TCB_CLKSRC
> >>> +	bool "TC Block Clocksource"
> >>
> >> The Kconfig options are set now with the COMPILE_TEST option in order to
> >> increase the compilation test coverage.
> >>
> >> Please, add bool "TC Block Clocksource" if COMPILE_TEST, ...
> >>
> >>> +	select REGMAP_MMIO
> >>> +	depends on GENERIC_CLOCKEVENTS
> >>> +	depends on SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> >>> +	default SOC_AT91RM9200 || SOC_AT91SAM9 || SOC_SAMA5
> >>
> >> ... remove these dependencies and let the SoC's Kconfig to select the timer
> >> like the other timers are.
> >>
> > 
> > The main issue with what you suggest is that it removes the possibility
> > to not compile the driver. This may be interesting for people using the
> > PIT as the clocksource/clockevent and the TCBs for something else.
> 
> Is it really a problem? We tend as much as possible to make silent
> options in order to let the platform config to select the right clock.
> 

I depends on how much you care about being able to remove as much as
possible from the kernel.
Both the PIT and the TCB can be used by AT91SAM9 and SAMA5, similarly,
both the system timer and the TCB can be used by AT91RM9200. I would
prefer letting the user select which drivers have to be compiled in the
kernel instead of pulling both with the SoC configuration.



-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

^ permalink raw reply	[flat|nested] 75+ messages in thread

end of thread, other threads:[~2017-05-16 14:35 UTC | newest]

Thread overview: 75+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-10 22:03 [PATCH 00/48] ARM: at91: rework Atmel TCB drivers Alexandre Belloni
2016-06-10 22:03 ` [PATCH 01/48] clk: at91: replace usleep() by udelay() calls Alexandre Belloni
2016-06-10 22:30   ` Arnd Bergmann
2016-06-10 22:37     ` Alexandre Belloni
2016-06-13 15:24     ` Alexandre Belloni
2016-06-13 19:26       ` Arnd Bergmann
2016-06-14 16:05       ` Afzal Mohammed
2016-06-14 16:18         ` Boris Brezillon
2016-06-11  7:49   ` Boris Brezillon
2016-06-10 22:03 ` [PATCH 02/48] ARM: at91: Document new TCB bindings Alexandre Belloni
2016-06-14 21:47   ` Rob Herring
2016-06-15  7:29     ` Boris Brezillon
2016-06-21 20:08       ` Rob Herring
2016-06-21 20:28       ` Rob Herring
2016-06-10 22:03 ` [PATCH 03/48] ARM: dts: at91: at91rm9200: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 04/48] ARM: dts: at91: at91rm9200ek; use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 05/48] ARM: dts: at91: mpa1600; " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 06/48] ARM: dts: at91: at91sam9260: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 07/48] ARM: dts: at91: ethernut5: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 08/48] ARM: dts: at91: foxg20: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 09/48] ARM: dts: at91: animeo_ip: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 10/48] ARM: dts: at91: kizbox: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 11/48] ARM: dts: at91: at91sam9g20ek: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 12/48] ARM: dts: at91: ge863-pro3: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 13/48] ARM: dts: at91: at91sam9261: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 14/48] ARM: dts: at91: at91sam9261ek: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 15/48] ARM: dts: at91: at91sam9263: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 16/48] ARM: dts: at91: at91sam9263ek: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 17/48] ARM: dts: at91: calao: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 18/48] ARM: dts: at91: at91sam9g45: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 19/48] ARM: dts: at91: at91sam9m10g45ek: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 20/48] ARM: dts: at91: pm9g45: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 21/48] ARM: dts: at91: at91sam9rl: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 22/48] ARM: dts: at91: at91sam9rlek: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 23/48] ARM: dts: at91: at91sam9n12: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 24/48] ARM: dts: at91: at91sam9n12ek: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 25/48] ARM: dts: at91: at91sam9x5: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 26/48] ARM: dts: at91: at91sam9x5cm: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 27/48] ARM: dts: at91: acme/g25: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 28/48] ARM: dts: at91: cosino: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 29/48] ARM: dts: at91: kizboxmini: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 30/48] ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 31/48] ARM: dts: at91: sama5d3xek; use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 32/48] ARM: dts: at91: sama5d3 Xplained: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 33/48] ARM: dts: at91: kizbox2: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 34/48] ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 35/48] ARM: dts: at91: sama5d4: Add TCB2 Alexandre Belloni
2016-06-10 22:03 ` [PATCH 36/48] ARM: dts: at91: sama5d4ek: use TCB2 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 37/48] ARM: dts: at91: sama5d4 Xplained: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 38/48] ARM: dts: at91: ma5d4: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 39/48] ARM: dts: at91: vinco: " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 40/48] ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices Alexandre Belloni
2016-06-10 22:03 ` [PATCH 41/48] ARM: dts: at91: sama5d2 Xplained: use TCB0 as clocksource Alexandre Belloni
2016-06-10 22:03 ` [PATCH 42/48] clocksource/drivers: Add a new driver for the Atmel ARM TC blocks Alexandre Belloni
2016-06-11 12:48   ` Boris Brezillon
2016-06-22 13:07     ` Daniel Lezcano
2016-06-22 13:13       ` Boris Brezillon
2016-06-24 10:07   ` Daniel Lezcano
2017-05-16 11:59     ` Alexandre Belloni
2017-05-16 14:25       ` Daniel Lezcano
2017-05-16 14:35         ` Alexandre Belloni
2016-06-10 22:03 ` [PATCH 43/48] clocksource/drivers: Add a clockevent driver for Atmel " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 44/48] clocksource: atmel-pit: allow unselecting ATMEL_PIT Alexandre Belloni
2016-06-11  9:43   ` Thomas Gleixner
2016-06-11 10:53     ` Alexandre Belloni
2016-06-13 19:04       ` Boris Brezillon
2016-06-13 19:14         ` Thomas Gleixner
2016-06-16 14:41           ` Boris Brezillon
2016-06-10 22:03 ` [PATCH 45/48] ARM: at91/defconfig: sama5: unselect ATMEL_PIT Alexandre Belloni
2016-06-10 22:03 ` [PATCH 46/48] ARM: at91/defconfig: at91_dt " Alexandre Belloni
2016-06-10 22:03 ` [PATCH 47/48] PWM: atmel-tcb: switch to new binding Alexandre Belloni
2016-06-11  2:22   ` kbuild test robot
2016-06-10 22:03 ` [PATCH 48/48] ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding Alexandre Belloni
2016-06-11  0:14   ` kbuild test robot
2016-06-11 10:25     ` Alexandre Belloni

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).