linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Keerthy <j-keerthy@ti.com>
To: <broonie@kernel.org>, <lee.jones@linaro.org>, <linus.walleij@linaro.org>
Cc: <linux-omap@vger.kernel.org>, <robh+dt@kernel.org>,
	<linux-gpio@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <j-keerthy@ti.com>
Subject: [PATCH v8 2/3] gpio: lp873x: Add support for General Purpose Outputs
Date: Fri, 12 Aug 2016 10:28:08 +0530	[thread overview]
Message-ID: <1470977889-27991-3-git-send-email-j-keerthy@ti.com> (raw)
In-Reply-To: <1470977889-27991-1-git-send-email-j-keerthy@ti.com>

Add driver for lp873x PMIC family GPOs. Two GPOs are supported
and can be configured in Open-drain output or Push-pull output.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
---

Changes in v8:

  * Replaced hardcoded bit fields with macros.

 drivers/gpio/Kconfig       |  10 +++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-lp873x.c | 193 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 204 insertions(+)
 create mode 100644 drivers/gpio/gpio-lp873x.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 6de9062..ff68a80 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -853,6 +853,16 @@ config GPIO_LP3943
 	  LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
 	  Open drain outputs are required for this usage.
 
+config GPIO_LP873X
+	tristate "TI LP873X GPO"
+	depends on MFD_TI_LP873X
+	help
+	  This driver supports the GPO on TI Lp873x PMICs. 2 GPOs are present
+	  on LP873X PMICs.
+
+	  This driver can also be built as a module. If so, the module will be
+          called gpio-lp873x.
+
 config GPIO_MAX77620
 	tristate "GPIO support for PMIC MAX77620 and MAX20024"
 	depends on MFD_MAX77620
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 2a035ed..d60432f 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -56,6 +56,7 @@ obj-$(CONFIG_GPIO_LOONGSON)	+= gpio-loongson.o
 obj-$(CONFIG_GPIO_LP3943)	+= gpio-lp3943.o
 obj-$(CONFIG_GPIO_LPC18XX)	+= gpio-lpc18xx.o
 obj-$(CONFIG_ARCH_LPC32XX)	+= gpio-lpc32xx.o
+obj-$(CONFIG_GPIO_LP873X)	+= gpio-lp873x.o
 obj-$(CONFIG_GPIO_LYNXPOINT)	+= gpio-lynxpoint.o
 obj-$(CONFIG_GPIO_MAX730X)	+= gpio-max730x.o
 obj-$(CONFIG_GPIO_MAX7300)	+= gpio-max7300.o
diff --git a/drivers/gpio/gpio-lp873x.c b/drivers/gpio/gpio-lp873x.c
new file mode 100644
index 0000000..79c255d
--- /dev/null
+++ b/drivers/gpio/gpio-lp873x.c
@@ -0,0 +1,193 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *	Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License version 2 for more details.
+ *
+ * Based on the TPS65218 driver
+ */
+
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <linux/mfd/lp873x.h>
+
+#define BITS_PER_GPO		0x4
+#define LP873X_GPO_CTRL_OD	0x2
+
+struct lp873x_gpio {
+	struct gpio_chip chip;
+	struct lp873x *lp873;
+};
+
+static int lp873x_gpio_get_direction(struct gpio_chip *chip,
+				     unsigned int offset)
+{
+	/* This device is output only */
+	return 0;
+}
+
+static int lp873x_gpio_direction_input(struct gpio_chip *chip,
+				       unsigned int offset)
+{
+	/* This device is output only */
+	return -EINVAL;
+}
+
+static int lp873x_gpio_direction_output(struct gpio_chip *chip,
+					unsigned int offset, int value)
+{
+	struct lp873x_gpio *gpio = gpiochip_get_data(chip);
+
+	/* Set the initial value */
+	return regmap_update_bits(gpio->lp873->regmap, LP873X_REG_GPO_CTRL,
+				  BIT(offset * BITS_PER_GPO),
+				  value ? BIT(offset * BITS_PER_GPO) : 0);
+}
+
+static int lp873x_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct lp873x_gpio *gpio = gpiochip_get_data(chip);
+	int ret, val;
+
+	ret = regmap_read(gpio->lp873->regmap, LP873X_REG_GPO_CTRL, &val);
+	if (ret < 0)
+		return ret;
+
+	return val & BIT(offset * BITS_PER_GPO);
+}
+
+static void lp873x_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			    int value)
+{
+	struct lp873x_gpio *gpio = gpiochip_get_data(chip);
+
+	regmap_update_bits(gpio->lp873->regmap, LP873X_REG_GPO_CTRL,
+			   BIT(offset * BITS_PER_GPO),
+			   value ? BIT(offset * BITS_PER_GPO) : 0);
+}
+
+static int lp873x_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+	struct lp873x_gpio *gpio = gpiochip_get_data(gc);
+	int ret;
+
+	switch (offset) {
+	case 0:
+		/* No MUX Set up Needed for GPO */
+		break;
+	case 1:
+		/* Setup the CLKIN_PIN_SEL MUX to GPO2 */
+		ret = regmap_update_bits(gpio->lp873->regmap, LP873X_REG_CONFIG,
+					 LP873X_CONFIG_CLKIN_PIN_SEL, 0);
+		if (ret)
+			return ret;
+
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int lp873x_gpio_set_single_ended(struct gpio_chip *gc,
+					unsigned int offset,
+					enum single_ended_mode mode)
+{
+	struct lp873x_gpio *gpio = gpiochip_get_data(gc);
+
+	switch (mode) {
+	case LINE_MODE_OPEN_DRAIN:
+		return regmap_update_bits(gpio->lp873->regmap,
+					  LP873X_REG_GPO_CTRL,
+					  BIT(offset * BITS_PER_GPO +
+					  LP873X_GPO_CTRL_OD),
+					  BIT(offset * BITS_PER_GPO +
+					  LP873X_GPO_CTRL_OD));
+	case LINE_MODE_PUSH_PULL:
+		return regmap_update_bits(gpio->lp873->regmap,
+					  LP873X_REG_GPO_CTRL,
+					  BIT(offset * BITS_PER_GPO +
+					  LP873X_GPO_CTRL_OD), 0);
+	default:
+		return -ENOTSUPP;
+	}
+}
+
+static struct gpio_chip template_chip = {
+	.label			= "lp873x-gpio",
+	.owner			= THIS_MODULE,
+	.request		= lp873x_gpio_request,
+	.get_direction		= lp873x_gpio_get_direction,
+	.direction_input	= lp873x_gpio_direction_input,
+	.direction_output	= lp873x_gpio_direction_output,
+	.get			= lp873x_gpio_get,
+	.set			= lp873x_gpio_set,
+	.set_single_ended	= lp873x_gpio_set_single_ended,
+	.base			= -1,
+	.ngpio			= 2,
+	.can_sleep		= true,
+};
+
+static int lp873x_gpio_probe(struct platform_device *pdev)
+{
+	struct lp873x_gpio *gpio;
+	int ret;
+
+	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
+	if (!gpio)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, gpio);
+
+	gpio->lp873 = dev_get_drvdata(pdev->dev.parent);
+	gpio->chip = template_chip;
+	gpio->chip.parent = gpio->lp873->dev;
+
+	ret = gpiochip_add_data(&gpio->chip, gpio);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Could not register gpiochip, %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int lp873x_gpio_remove(struct platform_device *pdev)
+{
+	struct lp873x_gpio *gpio = platform_get_drvdata(pdev);
+
+	gpiochip_remove(&gpio->chip);
+
+	return 0;
+}
+
+static const struct platform_device_id lp873x_gpio_id_table[] = {
+	{ "lp873x-gpio", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, lp873x_gpio_id_table);
+
+static struct platform_driver lp873x_gpio_driver = {
+	.driver = {
+		.name = "lp873x-gpio",
+	},
+	.probe = lp873x_gpio_probe,
+	.remove = lp873x_gpio_remove,
+	.id_table = lp873x_gpio_id_table,
+};
+module_platform_driver(lp873x_gpio_driver);
+
+MODULE_AUTHOR("Keerthy <j-keerthy@ti.com>");
+MODULE_DESCRIPTION("LP873X GPIO driver");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

  parent reply	other threads:[~2016-08-12  4:59 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-08-12  4:58 [PATCH v8 0/3] mfd: lp873x: Add lp873x PMIC support Keerthy
2016-08-12  4:58 ` [PATCH v8 1/3] " Keerthy
2016-08-31  7:56   ` Lee Jones
2016-08-31  8:13     ` Keerthy
2016-08-31 11:16       ` Lee Jones
2016-08-12  4:58 ` Keerthy [this message]
2016-08-12  4:58 ` [PATCH v8 3/3] regulator: lp873x: Change the MFD config option as per latest naming Keerthy

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1470977889-27991-3-git-send-email-j-keerthy@ti.com \
    --to=j-keerthy@ti.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=lee.jones@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).