[PATCH v2 0/2] Support for Axentia TSE-850

[PATCH v2 0/2] Support for Axentia TSE-850

[Peter Rosin]

Hi!

changes v1 -> v2
- squash the fixup into the correct patch, sorry for the noise.

After finally having all essintial drivers upstreamed (the
last ones are currently in -next) I would like to have the
dts and the defconfig also upstreamed.

checkpatch complains about missing docs for some compatible
strings:

axentia,tse850v3   (v3 is the hw version that we currently use)
axentia,tse850     (in case we have future versions with commonality)
axentia,linea      (the cpu module, reused in other products as well)
nxp,se97b          (temp sensor in the below eeprom module)
nxp,24c02          (eeprom on the main board)
st,24c64           (eeprom on the cpu module)

I don't know where I should document those, or if it's even
needed? I get the feeling that the last three are not "my fault".
Anyway, please advice. Or, even better, apply as-is... :-)

Cheers,
Peter

Peter Rosin (2):
  ARM: dts: add devicetree for the Axentia TSE-850
  ARM: tse850_defconfig: add Axentia TSE-850

 MAINTAINERS                            |   7 +
 arch/arm/boot/dts/Makefile             |   1 +
 arch/arm/boot/dts/axentia-linea.dtsi   |  52 +++++++
 arch/arm/boot/dts/axentia-tse850-3.dts | 275 +++++++++++++++++++++++++++++++++
 arch/arm/configs/tse850_defconfig      | 223 ++++++++++++++++++++++++++
 5 files changed, 558 insertions(+)
 create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
 create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
 create mode 100644 arch/arm/configs/tse850_defconfig

-- 
2.1.4

[PATCH v2 1/2] ARM: dts: add devicetree for the Axentia TSE-850

[Peter Rosin]

Signed-off-by: Peter Rosin <peda@axentia.se>
---
 MAINTAINERS                            |   6 +
 arch/arm/boot/dts/Makefile             |   1 +
 arch/arm/boot/dts/axentia-linea.dtsi   |  52 +++++++
 arch/arm/boot/dts/axentia-tse850-3.dts | 275 +++++++++++++++++++++++++++++++++
 4 files changed, 334 insertions(+)
 create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
 create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts

diff --git a/MAINTAINERS b/MAINTAINERS
index 9fe1bc9b414f..7ecf50e5ab47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2325,6 +2325,12 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/sound/axentia,*
 F:	sound/soc/atmel/tse850-pcm5142.c
 
+AXENTIA ARM DEVICES
+M:	Peter Rosin <peda@axentia.se>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/boot/dts/axentia-*
+
 AZ6007 DVB DRIVER
 M:	Mauro Carvalho Chehab <mchehab@s-opensource.com>
 M:	Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd2619902..02cd9b4c55d3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-kizbox2.dtb \
 	at91-sama5d2_xplained.dtb \
 	at91-sama5d3_xplained.dtb \
+	axentia-tse850-3.dtb \
 	sama5d31ek.dtb \
 	sama5d33ek.dtb \
 	sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/axentia-linea.dtsi b/arch/arm/boot/dts/axentia-linea.dtsi
new file mode 100644
index 000000000000..07359f9d7419
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-linea.dtsi
@@ -0,0 +1,52 @@
+/*
+ * axentia-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ *                    Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+	compatible = "axentia,linea",
+		     "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	memory {
+		reg = <0x20000000 0x20000000>;
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&main {
+	clock-frequency = <12000000>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "st,24c64";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&nand0 {
+	status = "okay";
+
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	atmel,has-pmecc;
+	atmel,pmecc-cap = <4>;
+	atmel,pmecc-sector-size = <512>;
+	nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
new file mode 100644
index 000000000000..517381f89c3d
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -0,0 +1,275 @@
+/*
+ * axentia-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ *                    Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "axentia-linea.dtsi"
+
+/ {
+	model = "Axentia TSE-850 3.0";
+	compatible = "axentia,tse850v3", "axentia,tse850", "axentia,linea",
+		     "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+	};
+
+	ahb {
+		apb {
+			pinctrl@fffff200 {
+				tse850 {
+					pinctrl_usba_vbus: usba-vbus {
+						atmel,pins =
+							<AT91_PIOC 31
+							 AT91_PERIPH_GPIO
+							 AT91_PINCTRL_DEGLITCH>;
+					};
+				};
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+	};
+
+	sck: oscillator {
+		compatible = "fixed-clock";
+
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+		clock-output-names = "sck";
+	};
+
+	reg_3v3: regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "3v3-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	ana: reg-ana {
+		compatible = "pwm-regulator";
+
+		regulator-name = "ANA";
+
+		pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+		pwm-dutycycle-unit = <1000>;
+		pwm-dutycycle-range = <100 1000>;
+
+		regulator-min-microvolt = <2000000>;
+		regulator-max-microvolt = <20000000>;
+		regulator-ramp-delay = <1000>;
+	};
+
+	sound {
+		compatible = "axentia,tse850-pcm5142";
+
+		axentia,ssc-controller = <&ssc0>;
+		axentia,audio-codec = <&pcm5142>;
+
+		axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+		axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+		axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+		axentia,ana-supply = <&ana>;
+	};
+
+	dac: dpot-dac {
+		compatible = "dpot-dac";
+		vref-supply = <&reg_3v3>;
+		io-channels = <&dpot 0>;
+		io-channel-names = "dpot";
+		#io-channel-cells = <1>;
+	};
+
+	envelope-detector {
+		compatible = "axentia,tse850-envelope-detector";
+		io-channels = <&dac 0>;
+		io-channel-names = "dac";
+
+		interrupt-parent = <&pioA>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "comp";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		ch1-red {
+			label = "ch-1:red";
+			gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+		};
+		ch1-green {
+			label = "ch-1:green";
+			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+		};
+		ch2-red {
+			label = "ch-2:red";
+			gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+		};
+		ch2-green {
+			label = "ch-2:green";
+			gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+		};
+		data-red {
+			label = "data:red";
+			gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+		};
+		data-green {
+			label = "data:green";
+			gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+		};
+		alarm-red {
+			label = "alarm:red";
+			gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+		};
+		alarm-green {
+			label = "alarm:green";
+			gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&nand0 {
+	at91bootstrap@0 {
+		label = "at91bootstrap";
+		reg = <0x0 0x40000>;
+	};
+
+	barebox@40000 {
+		label = "bootloader";
+		reg = <0x40000 0x60000>;
+	};
+
+	bareboxenv@c0000 {
+		label = "bareboxenv";
+		reg = <0xc0000 0x40000>;
+	};
+
+	bareboxenv2@100000 {
+		label = "bareboxenv2";
+		reg = <0x100000 0x40000>;
+	};
+
+	oftree@180000 {
+		label = "oftree";
+		reg = <0x180000 0x20000>;
+	};
+
+	kernel@200000 {
+		label = "kernel";
+		reg = <0x200000 0x500000>;
+	};
+
+	rootfs@800000 {
+		label = "rootfs";
+		reg = <0x800000 0x0f800000>;
+	};
+
+	ovlfs@10000000 {
+		label = "ovlfs";
+		reg = <0x10000000 0x10000000>;
+	};
+};
+
+&ssc0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	jc42@18 {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x18>;
+	};
+
+	dpot: mcp4651-104@28 {
+		compatible = "microchip,mcp4651-104";
+		reg = <0x28>;
+		#io-channel-cells = <1>;
+	};
+
+	pcm5142: pcm5142@4c {
+		compatible = "ti,pcm5142";
+
+		reg = <0x4c>;
+
+		AVDD-supply = <&reg_3v3>;
+		DVDD-supply = <&reg_3v3>;
+		CPVDD-supply = <&reg_3v3>;
+
+		clocks = <&sck>;
+
+		pll-in = <3>;
+		pll-out = <6>;
+	};
+
+	eeprom@50 {
+		compatible = "nxp,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&usart0 {
+	status = "okay";
+
+	atmel,use-dma-rx;
+};
+
+&pwm0 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+	pinctrl-names = "default";
+};
+
+&macb1 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	phy0: ethernet-phy@3 {
+		reg = <3>;
+
+		interrupt-parent = <&pioE>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&usb0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+	status = "okay";
+
+	num-ports = <1>;
+	atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+	atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+
+	dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
+};
-- 
2.1.4

[PATCH v2 2/2] ARM: tse850_defconfig: add Axentia TSE-850

[Peter Rosin]

Signed-off-by: Peter Rosin <peda@axentia.se>
---
 MAINTAINERS                       |   1 +
 arch/arm/configs/tse850_defconfig | 223 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 224 insertions(+)
 create mode 100644 arch/arm/configs/tse850_defconfig

diff --git a/MAINTAINERS b/MAINTAINERS
index 7ecf50e5ab47..883d46eb2a06 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2330,6 +2330,7 @@ M:	Peter Rosin <peda@axentia.se>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/boot/dts/axentia-*
+F:	arch/arm/configs/tse850_defconfig
 
 AZ6007 DVB DRIVER
 M:	Mauro Carvalho Chehab <mchehab@s-opensource.com>
diff --git a/arch/arm/configs/tse850_defconfig b/arch/arm/configs/tse850_defconfig
new file mode 100644
index 000000000000..f6076e7e1669
--- /dev/null
+++ b/arch/arm/configs/tse850_defconfig
@@ -0,0 +1,223 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_FHANDLE is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D3=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_XFRM_USER=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPGRE_DEMUX=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_UDP_DIAG=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_TABLES=y
+CONFIG_NF_TABLES_INET=y
+CONFIG_NF_TABLES_NETDEV=y
+CONFIG_NFT_EXTHDR=y
+CONFIG_NFT_META=y
+CONFIG_NFT_NUMGEN=y
+CONFIG_NFT_CT=y
+CONFIG_NFT_SET_RBTREE=y
+CONFIG_NFT_SET_HASH=y
+CONFIG_NFT_COUNTER=y
+CONFIG_NFT_LOG=y
+CONFIG_NFT_LIMIT=y
+CONFIG_NFT_QUOTA=y
+CONFIG_NFT_REJECT=y
+CONFIG_NFT_HASH=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ARC is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_HISILICON is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_USB_NET_DRIVERS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_LEDS is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_SENSORS_JC42=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=y
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_ISD200=y
+CONFIG_USB_STORAGE_USBAT=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+CONFIG_USB_STORAGE_ALAUDA=y
+CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_KARMA=y
+CONFIG_USB_STORAGE_CYPRESS_ATACB=y
+CONFIG_USB_STORAGE_ENE_UB6250=y
+CONFIG_USB_UAS=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_OVERLAY_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+# CONFIG_DETECT_HUNG_TASK is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
-- 
2.1.4