* [PATCH 1/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
2016-12-20 16:10 ` [PATCH 2/3] " Geoff Lansberry
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
The TRF7970A has configuration options for supporting hardware designs
with 1.8 Volt or 3.3 Volt IO. This commit adds a device tree option,
using a fixed regulator binding, for setting the io voltage to match
the hardware configuration. If no option is supplied it defaults to
3.3 volt configuration.
---
.../devicetree/bindings/net/nfc/trf7970a.txt | 4 ++--
drivers/nfc/trf7970a.c | 28 +++++++++++++++++++++-
2 files changed, 29 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index e262ac1..b5777d8 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,9 +21,9 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- vdd-io-supply: Regulator specifying voltage for vdd-io
- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
-
Example (for ARM-based BeagleBone with TRF7970A on SPI1):
&spi1 {
@@ -41,11 +41,11 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
<&gpio2 5 GPIO_ACTIVE_LOW>;
vin-supply = <&ldo3_reg>;
vin-voltage-override = <5000000>;
+ vdd-io-supply = <&ldo2_reg>;
autosuspend-delay = <30000>;
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
- vdd_io_1v8;
clock-frequency = <27120000>;
status = "okay";
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index c9cb278..94c31f8 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -444,6 +444,7 @@ struct trf7970a {
u8 iso_ctrl_tech;
u8 modulator_sys_clk_ctrl;
u8 special_fcn_reg1;
+ u8 io_ctrl;
unsigned int guard_time;
int technology;
int framing;
@@ -1051,6 +1052,11 @@ static int trf7970a_init(struct trf7970a *trf)
if (ret)
goto err_out;
+ ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
+ trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1));
+ if (ret)
+ goto err_out;
+
ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, 0);
if (ret)
goto err_out;
@@ -1767,7 +1773,7 @@ static int _trf7970a_tg_listen(struct nfc_digital_dev *ddev, u16 timeout,
goto out_err;
ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
- TRF7970A_REG_IO_CTRL_VRS(0x1));
+ trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1));
if (ret)
goto out_err;
@@ -2062,6 +2068,7 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+
of_property_read_u32(np, "clock-frequency", &clk_freq);
if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
@@ -2105,6 +2112,25 @@ static int trf7970a_probe(struct spi_device *spi)
if (uvolts > 4000000)
trf->chip_status_ctrl = TRF7970A_CHIP_STATUS_VRS5_3;
+ trf->regulator = devm_regulator_get(&spi->dev, "vdd-io");
+ if (IS_ERR(trf->regulator)) {
+ ret = PTR_ERR(trf->regulator);
+ dev_err(trf->dev, "Can't get VDD_IO regulator: %d\n", ret);
+ goto err_destroy_lock;
+ }
+
+ ret = regulator_enable(trf->regulator);
+ if (ret) {
+ dev_err(trf->dev, "Can't enable VDD_IO: %d\n", ret);
+ goto err_destroy_lock;
+ }
+
+
+ if (regulator_get_voltage(trf->regulator) == 1800000) {
+ trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW;
+ dev_dbg(trf->dev, "trf7970a config vdd_io to 1.8V\n");
+ }
+
trf->ddev = nfc_digital_allocate_device(&trf7970a_nfc_ops,
TRF7970A_SUPPORTED_PROTOCOLS,
NFC_DIGITAL_DRV_CAPS_IN_CRC |
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
2016-12-20 16:10 ` [PATCH 1/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
2016-12-20 16:10 ` [PATCH 2/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry
From: Geoff Lansberry <geoff@kuvee.com>
The TRF7970A has configuration options for supporting hardware designs
with 1.8 Volt or 3.3 Volt IO. This commit adds a device tree option,
using a fixed regulator binding, for setting the io voltage to match
the hardware configuration. If no option is supplied it defaults to
3.3 volt configuration.
---
.../devicetree/bindings/net/nfc/trf7970a.txt | 4 ++--
drivers/nfc/trf7970a.c | 28 +++++++++++++++++++++-
2 files changed, 29 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index e262ac1..b5777d8 100644
--- a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -21,9 +21,9 @@ Optional SoC Specific Properties:
- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
where an extra byte is returned by Read Multiple Block commands issued
to Type 5 tags.
+- vdd-io-supply: Regulator specifying voltage for vdd-io
- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz
-
Example (for ARM-based BeagleBone with TRF7970A on SPI1):
&spi1 {
@@ -41,11 +41,11 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
<&gpio2 5 GPIO_ACTIVE_LOW>;
vin-supply = <&ldo3_reg>;
vin-voltage-override = <5000000>;
+ vdd-io-supply = <&ldo2_reg>;
autosuspend-delay = <30000>;
irq-status-read-quirk;
en2-rf-quirk;
t5t-rmb-extra-byte-quirk;
- vdd_io_1v8;
clock-frequency = <27120000>;
status = "okay";
};
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 4e051e9..8a88195 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -444,6 +444,7 @@ struct trf7970a {
u8 iso_ctrl_tech;
u8 modulator_sys_clk_ctrl;
u8 special_fcn_reg1;
+ u8 io_ctrl;
unsigned int guard_time;
int technology;
int framing;
@@ -1051,6 +1052,11 @@ static int trf7970a_init(struct trf7970a *trf)
if (ret)
goto err_out;
+ ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
+ trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1));
+ if (ret)
+ goto err_out;
+
ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, 0);
if (ret)
goto err_out;
@@ -1767,7 +1773,7 @@ static int _trf7970a_tg_listen(struct nfc_digital_dev *ddev, u16 timeout,
goto out_err;
ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL,
- TRF7970A_REG_IO_CTRL_VRS(0x1));
+ trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1));
if (ret)
goto out_err;
@@ -2062,6 +2068,7 @@ static int trf7970a_probe(struct spi_device *spi)
return ret;
}
+
of_property_read_u32(np, "clock-frequency", &clk_freq);
if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
@@ -2105,6 +2112,25 @@ static int trf7970a_probe(struct spi_device *spi)
if (uvolts > 4000000)
trf->chip_status_ctrl = TRF7970A_CHIP_STATUS_VRS5_3;
+ trf->regulator = devm_regulator_get(&spi->dev, "vdd-io");
+ if (IS_ERR(trf->regulator)) {
+ ret = PTR_ERR(trf->regulator);
+ dev_err(trf->dev, "Can't get VDD_IO regulator: %d\n", ret);
+ goto err_destroy_lock;
+ }
+
+ ret = regulator_enable(trf->regulator);
+ if (ret) {
+ dev_err(trf->dev, "Can't enable VDD_IO: %d\n", ret);
+ goto err_destroy_lock;
+ }
+
+
+ if (regulator_get_voltage(trf->regulator) == 1800000) {
+ trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW;
+ dev_dbg(trf->dev, "trf7970a config vdd_io to 1.8V\n");
+ }
+
trf->ddev = nfc_digital_allocate_device(&trf7970a_nfc_ops,
TRF7970A_SUPPORTED_PROTOCOLS,
NFC_DIGITAL_DRV_CAPS_IN_CRC |
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
2016-12-20 16:10 ` [PATCH 1/3] NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage Geoff Lansberry
2016-12-20 16:10 ` [PATCH 2/3] " Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
2016-12-20 16:10 ` [PATCH 3/3] mod of frequency Geoff Lansberry
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin, Jaret Cantu,
Geoff Lansberry
From: Jaret Cantu <jaret.cantu@timesys.com>
Repeated polling attempts cause a NULL dereference error to occur.
This is because the state of the trf7970a is currently reading but
another request has been made to send a command before it has finished.
The solution is to properly kill the waiting reading (workqueue)
before failing on the send.
---
drivers/nfc/trf7970a.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 94c31f8..e9e93ea 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -1496,6 +1496,10 @@ static int trf7970a_send_cmd(struct nfc_digital_dev *ddev,
(trf->state != TRF7970A_ST_IDLE_RX_BLOCKED)) {
dev_err(trf->dev, "%s - Bogus state: %d\n", __func__,
trf->state);
+ if (trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA ||
+ trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA_CONT)
+ trf->ignore_timeout =
+ !cancel_delayed_work(&trf->timeout_work);
ret = -EIO;
goto out_err;
}
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/3] mod of frequency
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
` (2 preceding siblings ...)
2016-12-20 16:10 ` [PATCH 2/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
2016-12-20 16:10 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
2016-12-20 16:10 ` [PATCH 4/4] mod of frequency Geoff Lansberry
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry, Geoff Lansberry
---
drivers/nfc/trf7970a.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index e9e93ea..5916737 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -2076,10 +2076,10 @@ static int trf7970a_probe(struct spi_device *spi)
of_property_read_u32(np, "clock-frequency", &clk_freq);
if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
- dev_err(trf->dev,
- "clock-frequency (%u Hz) unsupported\n",
- clk_freq);
- return -EINVAL;
+ dev_err(trf->dev,
+ "clock-frequency (%u Hz) unsupported\n",
+ clk_freq);
+ return -EINVAL;
}
if (of_property_read_bool(np, "en2-rf-quirk"))
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
` (3 preceding siblings ...)
2016-12-20 16:10 ` [PATCH 3/3] mod of frequency Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
2016-12-20 16:10 ` [PATCH 4/4] mod of frequency Geoff Lansberry
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin, Jaret Cantu,
Geoff Lansberry
From: Jaret Cantu <jaret.cantu@timesys.com>
Repeated polling attempts cause a NULL dereference error to occur.
This is because the state of the trf7970a is currently reading but
another request has been made to send a command before it has finished.
The solution is to properly kill the waiting reading (workqueue)
before failing on the send.
---
drivers/nfc/trf7970a.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index 8a88195..5916737 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -1496,6 +1496,10 @@ static int trf7970a_send_cmd(struct nfc_digital_dev *ddev,
(trf->state != TRF7970A_ST_IDLE_RX_BLOCKED)) {
dev_err(trf->dev, "%s - Bogus state: %d\n", __func__,
trf->state);
+ if (trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA ||
+ trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA_CONT)
+ trf->ignore_timeout =
+ !cancel_delayed_work(&trf->timeout_work);
ret = -EIO;
goto out_err;
}
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 4/4] mod of frequency
2016-12-20 16:10 [PATCH 1/3] NFC: trf7970a: add device tree option for 27MHz clock Geoff Lansberry
` (4 preceding siblings ...)
2016-12-20 16:10 ` [PATCH 3/3] nfc: trf7970a: Prevent repeated polling from crashing the kernel Geoff Lansberry
@ 2016-12-20 16:10 ` Geoff Lansberry
5 siblings, 0 replies; 7+ messages in thread
From: Geoff Lansberry @ 2016-12-20 16:10 UTC (permalink / raw)
To: linux-wireless
Cc: lauro.venancio, aloisio.almeida, sameo, robh+dt, mark.rutland,
netdev, devicetree, linux-kernel, mgreer, justin,
Geoff Lansberry, Geoff Lansberry
---
drivers/nfc/trf7970a.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/nfc/trf7970a.c b/drivers/nfc/trf7970a.c
index e9e93ea..5916737 100644
--- a/drivers/nfc/trf7970a.c
+++ b/drivers/nfc/trf7970a.c
@@ -2076,10 +2076,10 @@ static int trf7970a_probe(struct spi_device *spi)
of_property_read_u32(np, "clock-frequency", &clk_freq);
if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY)) {
- dev_err(trf->dev,
- "clock-frequency (%u Hz) unsupported\n",
- clk_freq);
- return -EINVAL;
+ dev_err(trf->dev,
+ "clock-frequency (%u Hz) unsupported\n",
+ clk_freq);
+ return -EINVAL;
}
if (of_property_read_bool(np, "en2-rf-quirk"))
--
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
^ permalink raw reply related [flat|nested] 7+ messages in thread