LKML Archive on lore.kernel.org
 help / color / Atom feed
From: Alan Tull <atull@kernel.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Moritz Fischer <moritz.fischer@ettus.com>,
	Alan Tull <atull@kernel.org>,
	linux-kernel@vger.kernel.org, linux-fpga@vger.kernel.org,
	Anatolij Gustschin <agust@denx.de>
Subject: [PATCH 3/8] fpga manager: Add Xilinx slave serial SPI driver
Date: Thu, 23 Mar 2017 19:34:26 -0500
Message-ID: <1490315671-5076-4-git-send-email-atull@kernel.org> (raw)
In-Reply-To: <1490315671-5076-1-git-send-email-atull@kernel.org>

From: Anatolij Gustschin <agust@denx.de>

The driver loads FPGA firmware over SPI, using the "slave serial"
configuration interface on Xilinx FPGAs.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
---
 drivers/fpga/Kconfig      |   7 ++
 drivers/fpga/Makefile     |   1 +
 drivers/fpga/xilinx-spi.c | 198 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 206 insertions(+)
 create mode 100644 drivers/fpga/xilinx-spi.c

diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index dee470f..c81cb7d 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -46,6 +46,13 @@ config FPGA_MGR_TS73XX
 	  FPGA manager driver support for the Altera Cyclone II FPGA
 	  present on the TS-73xx SBC boards.
 
+config FPGA_MGR_XILINX_SPI
+	tristate "Xilinx Configuration over Slave Serial (SPI)"
+	depends on SPI
+	help
+	  FPGA manager driver support for Xilinx FPGA configuration
+	  over slave serial interface.
+
 config FPGA_MGR_ZYNQ_FPGA
 	tristate "Xilinx Zynq FPGA"
 	depends on ARCH_ZYNQ || COMPILE_TEST
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index a5ee3ff..c6f5d74 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_FPGA_MGR_ICE40_SPI)	+= ice40-spi.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA)		+= socfpga.o
 obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10)	+= socfpga-a10.o
 obj-$(CONFIG_FPGA_MGR_TS73XX)		+= ts73xx-fpga.o
+obj-$(CONFIG_FPGA_MGR_XILINX_SPI)	+= xilinx-spi.o
 obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA)	+= zynq-fpga.o
 
 # FPGA Bridge Drivers
diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
new file mode 100644
index 0000000..9b62a4c
--- /dev/null
+++ b/drivers/fpga/xilinx-spi.c
@@ -0,0 +1,198 @@
+/*
+ * Xilinx Spartan6 Slave Serial SPI Driver
+ *
+ * Copyright (C) 2017 DENX Software Engineering
+ *
+ * Anatolij Gustschin <agust@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * Manage Xilinx FPGA firmware that is loaded over SPI using
+ * the slave serial configuration interface.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/of.h>
+#include <linux/spi/spi.h>
+#include <linux/sizes.h>
+
+struct xilinx_spi_conf {
+	struct spi_device *spi;
+	struct gpio_desc *prog_b;
+	struct gpio_desc *done;
+};
+
+static enum fpga_mgr_states xilinx_spi_state(struct fpga_manager *mgr)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+
+	if (!gpiod_get_value(conf->done))
+		return FPGA_MGR_STATE_RESET;
+
+	return FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int xilinx_spi_write_init(struct fpga_manager *mgr,
+				 struct fpga_image_info *info,
+				 const char *buf, size_t count)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	const size_t prog_latency_7500us = 7500;
+	const size_t prog_pulse_1us = 1;
+
+	if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
+		dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
+		return -EINVAL;
+	}
+
+	gpiod_set_value(conf->prog_b, 1);
+
+	udelay(prog_pulse_1us); /* min is 500 ns */
+
+	gpiod_set_value(conf->prog_b, 0);
+
+	if (gpiod_get_value(conf->done)) {
+		dev_err(&mgr->dev, "Unexpected DONE pin state...\n");
+		return -EIO;
+	}
+
+	/* program latency */
+	usleep_range(prog_latency_7500us, prog_latency_7500us + 100);
+	return 0;
+}
+
+static int xilinx_spi_write(struct fpga_manager *mgr, const char *buf,
+			    size_t count)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	const char *fw_data = buf;
+	const char *fw_data_end = fw_data + count;
+
+	while (fw_data < fw_data_end) {
+		size_t remaining, stride;
+		int ret;
+
+		remaining = fw_data_end - fw_data;
+		stride = min_t(size_t, remaining, SZ_4K);
+
+		ret = spi_write(conf->spi, fw_data, stride);
+		if (ret) {
+			dev_err(&mgr->dev, "SPI error in firmware write: %d\n",
+				ret);
+			return ret;
+		}
+		fw_data += stride;
+	}
+
+	return 0;
+}
+
+static int xilinx_spi_apply_cclk_cycles(struct xilinx_spi_conf *conf)
+{
+	struct spi_device *spi = conf->spi;
+	const u8 din_data[1] = { 0xff };
+	int ret;
+
+	ret = spi_write(conf->spi, din_data, sizeof(din_data));
+	if (ret)
+		dev_err(&spi->dev, "applying CCLK cycles failed: %d\n", ret);
+
+	return ret;
+}
+
+static int xilinx_spi_write_complete(struct fpga_manager *mgr,
+				     struct fpga_image_info *info)
+{
+	struct xilinx_spi_conf *conf = mgr->priv;
+	unsigned long timeout;
+	int ret;
+
+	if (gpiod_get_value(conf->done))
+		return xilinx_spi_apply_cclk_cycles(conf);
+
+	timeout = jiffies + usecs_to_jiffies(info->config_complete_timeout_us);
+
+	while (time_before(jiffies, timeout)) {
+
+		ret = xilinx_spi_apply_cclk_cycles(conf);
+		if (ret)
+			return ret;
+
+		if (gpiod_get_value(conf->done))
+			return xilinx_spi_apply_cclk_cycles(conf);
+	}
+
+	dev_err(&mgr->dev, "Timeout after config data transfer.\n");
+	return -ETIMEDOUT;
+}
+
+static const struct fpga_manager_ops xilinx_spi_ops = {
+	.state = xilinx_spi_state,
+	.write_init = xilinx_spi_write_init,
+	.write = xilinx_spi_write,
+	.write_complete = xilinx_spi_write_complete,
+};
+
+static int xilinx_spi_probe(struct spi_device *spi)
+{
+	struct xilinx_spi_conf *conf;
+
+	conf = devm_kzalloc(&spi->dev, sizeof(*conf), GFP_KERNEL);
+	if (!conf)
+		return -ENOMEM;
+
+	conf->spi = spi;
+
+	/* PROGRAM_B is active low */
+	conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
+	if (IS_ERR(conf->prog_b)) {
+		dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
+			PTR_ERR(conf->prog_b));
+		return PTR_ERR(conf->prog_b);
+	}
+
+	conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
+	if (IS_ERR(conf->done)) {
+		dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
+			PTR_ERR(conf->done));
+		return PTR_ERR(conf->done);
+	}
+
+	return fpga_mgr_register(&spi->dev, "Xilinx Slave Serial FPGA Manager",
+				 &xilinx_spi_ops, conf);
+}
+
+static int xilinx_spi_remove(struct spi_device *spi)
+{
+	fpga_mgr_unregister(&spi->dev);
+
+	return 0;
+}
+
+static const struct of_device_id xlnx_spi_of_match[] = {
+	{ .compatible = "xlnx,fpga-slave-serial", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, xlnx_spi_of_match);
+
+static struct spi_driver xilinx_slave_spi_driver = {
+	.driver = {
+		.name = "xlnx-slave-spi",
+		.of_match_table = of_match_ptr(xlnx_spi_of_match),
+	},
+	.probe = xilinx_spi_probe,
+	.remove = xilinx_spi_remove,
+};
+
+module_spi_driver(xilinx_slave_spi_driver)
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
+MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SPI");
-- 
2.7.4

  parent reply index

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-03-24  0:34 [PATCH 0/8] patches for fpga Alan Tull
2017-03-24  0:34 ` [PATCH 1/8] fpga: altera_freeze_bridge: Constify ops Alan Tull
2017-03-24  0:34 ` [PATCH 2/8] dt: bindings: fpga: add xilinx slave-serial binding description Alan Tull
2017-03-24  0:34 ` Alan Tull [this message]
2017-03-24  0:34 ` [PATCH 4/8] fpga: add config complete timeout Alan Tull
2017-03-24  0:34 ` [PATCH 5/8] fpga pr ip: Core driver support for Altera Partial Reconfiguration IP Alan Tull
2017-03-24  0:34 ` [PATCH 6/8] fpga dt: bindings " Alan Tull
2017-03-24  0:34 ` [PATCH 7/8] fpga pr ip: Platform driver " Alan Tull
2017-03-24  0:34 ` [PATCH 8/8] MAINTAINERS: Add file patterns for fpga device tree bindings Alan Tull

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1490315671-5076-4-git-send-email-atull@kernel.org \
    --to=atull@kernel.org \
    --cc=agust@denx.de \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-fpga@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=moritz.fischer@ettus.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

LKML Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/lkml/0 lkml/git/0.git
	git clone --mirror https://lore.kernel.org/lkml/1 lkml/git/1.git
	git clone --mirror https://lore.kernel.org/lkml/2 lkml/git/2.git
	git clone --mirror https://lore.kernel.org/lkml/3 lkml/git/3.git
	git clone --mirror https://lore.kernel.org/lkml/4 lkml/git/4.git
	git clone --mirror https://lore.kernel.org/lkml/5 lkml/git/5.git
	git clone --mirror https://lore.kernel.org/lkml/6 lkml/git/6.git
	git clone --mirror https://lore.kernel.org/lkml/7 lkml/git/7.git
	git clone --mirror https://lore.kernel.org/lkml/8 lkml/git/8.git
	git clone --mirror https://lore.kernel.org/lkml/9 lkml/git/9.git
	git clone --mirror https://lore.kernel.org/lkml/10 lkml/git/10.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 lkml lkml/ https://lore.kernel.org/lkml \
		linux-kernel@vger.kernel.org
	public-inbox-index lkml

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git