From: Lin Yun Sheng <linyunsheng@huawei.com>
To: <davem@davemloft.net>, <andrew@lunn.ch>, <f.fainelli@gmail.com>
Cc: <huangdaode@hisilicon.com>, <xuwei5@hisilicon.com>,
<liguozhu@hisilicon.com>, <Yisen.Zhuang@huawei.com>,
<gabriele.paoloni@huawei.com>, <john.garry@huawei.com>,
<linuxarm@huawei.com>, <yisen.zhuang@huawei.com>,
<salil.mehta@huawei.com>, <lipeng321@huawei.com>,
<tremyfr@gmail.com>, <netdev@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Subject: [PATCH NET V5 2/2] net: hns: Use phy_driver to setup Phy loopback
Date: Mon, 26 Jun 2017 10:10:39 +0800 [thread overview]
Message-ID: <1498443039-134503-3-git-send-email-linyunsheng@huawei.com> (raw)
In-Reply-To: <1498443039-134503-1-git-send-email-linyunsheng@huawei.com>
Use function set_loopback in phy_driver to setup phy loopback
when doing ethtool self test.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
---
drivers/net/ethernet/hisilicon/hns/hnae.h | 1 +
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c | 92 +++++++-----------------
2 files changed, 26 insertions(+), 67 deletions(-)
diff --git a/drivers/net/ethernet/hisilicon/hns/hnae.h b/drivers/net/ethernet/hisilicon/hns/hnae.h
index 04211ac..7ba653a 100644
--- a/drivers/net/ethernet/hisilicon/hns/hnae.h
+++ b/drivers/net/ethernet/hisilicon/hns/hnae.h
@@ -360,6 +360,7 @@ enum hnae_loop {
MAC_INTERNALLOOP_MAC = 0,
MAC_INTERNALLOOP_SERDES,
MAC_INTERNALLOOP_PHY,
+ MAC_LOOP_PHY_NONE,
MAC_LOOP_NONE,
};
diff --git a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
index e95795b..10d82df 100644
--- a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
+++ b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
@@ -259,67 +259,24 @@ static int hns_nic_set_link_ksettings(struct net_device *net_dev,
static int hns_nic_config_phy_loopback(struct phy_device *phy_dev, u8 en)
{
-#define COPPER_CONTROL_REG 0
-#define PHY_POWER_DOWN BIT(11)
-#define PHY_LOOP_BACK BIT(14)
- u16 val = 0;
-
- if (phy_dev->is_c45) /* c45 branch adding for XGE PHY */
- return -ENOTSUPP;
+ int err;
if (en) {
- /* speed : 1000M */
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 2);
- phy_write(phy_dev, 21, 0x1046);
-
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
- /* Force Master */
- phy_write(phy_dev, 9, 0x1F00);
-
- /* Soft-reset */
- phy_write(phy_dev, 0, 0x9140);
- /* If autoneg disabled,two soft-reset operations */
- phy_write(phy_dev, 0, 0x9140);
-
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 0xFA);
-
- /* Default is 0x0400 */
- phy_write(phy_dev, 1, 0x418);
-
- /* Force 1000M Link, Default is 0x0200 */
- phy_write(phy_dev, 7, 0x20C);
-
- /* Powerup Fiber */
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 1);
- val = phy_read(phy_dev, COPPER_CONTROL_REG);
- val &= ~PHY_POWER_DOWN;
- phy_write(phy_dev, COPPER_CONTROL_REG, val);
-
- /* Enable Phy Loopback */
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
- val = phy_read(phy_dev, COPPER_CONTROL_REG);
- val |= PHY_LOOP_BACK;
- val &= ~PHY_POWER_DOWN;
- phy_write(phy_dev, COPPER_CONTROL_REG, val);
+ err = phy_resume(phy_dev);
+ if (err)
+ goto out;
+
+ err = phy_loopback(phy_dev, true);
} else {
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 0xFA);
- phy_write(phy_dev, 1, 0x400);
- phy_write(phy_dev, 7, 0x200);
-
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 1);
- val = phy_read(phy_dev, COPPER_CONTROL_REG);
- val |= PHY_POWER_DOWN;
- phy_write(phy_dev, COPPER_CONTROL_REG, val);
-
- phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
- phy_write(phy_dev, 9, 0xF00);
-
- val = phy_read(phy_dev, COPPER_CONTROL_REG);
- val &= ~PHY_LOOP_BACK;
- val |= PHY_POWER_DOWN;
- phy_write(phy_dev, COPPER_CONTROL_REG, val);
+ err = phy_loopback(phy_dev, false);
+ if (err)
+ goto out;
+
+ err = phy_suspend(phy_dev);
}
- return 0;
+
+out:
+ return err;
}
static int __lb_setup(struct net_device *ndev,
@@ -332,10 +289,8 @@ static int __lb_setup(struct net_device *ndev,
switch (loop) {
case MAC_INTERNALLOOP_PHY:
- if ((phy_dev) && (!phy_dev->is_c45)) {
- ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
- ret |= h->dev->ops->set_loopback(h, loop, 0x1);
- }
+ ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
+ ret |= h->dev->ops->set_loopback(h, loop, 0x1);
break;
case MAC_INTERNALLOOP_MAC:
if ((h->dev->ops->set_loopback) &&
@@ -346,10 +301,9 @@ static int __lb_setup(struct net_device *ndev,
if (h->dev->ops->set_loopback)
ret = h->dev->ops->set_loopback(h, loop, 0x1);
break;
+ case MAC_LOOP_PHY_NONE:
+ ret |= hns_nic_config_phy_loopback(phy_dev, 0x0);
case MAC_LOOP_NONE:
- if ((phy_dev) && (!phy_dev->is_c45))
- ret |= hns_nic_config_phy_loopback(phy_dev, 0x0);
-
if (h->dev->ops->set_loopback) {
if (priv->ae_handle->phy_if != PHY_INTERFACE_MODE_XGMII)
ret |= h->dev->ops->set_loopback(h,
@@ -582,13 +536,16 @@ static int __lb_run_test(struct net_device *ndev,
return ret_val;
}
-static int __lb_down(struct net_device *ndev)
+static int __lb_down(struct net_device *ndev, enum hnae_loop loop)
{
struct hns_nic_priv *priv = netdev_priv(ndev);
struct hnae_handle *h = priv->ae_handle;
int ret;
- ret = __lb_setup(ndev, MAC_LOOP_NONE);
+ if (loop == MAC_INTERNALLOOP_PHY)
+ ret = __lb_setup(ndev, MAC_LOOP_PHY_NONE);
+ else
+ ret = __lb_setup(ndev, MAC_LOOP_NONE);
if (ret)
netdev_err(ndev, "%s: __lb_setup return error(%d)!\n",
__func__,
@@ -644,7 +601,8 @@ static void hns_nic_self_test(struct net_device *ndev,
if (!data[test_index]) {
data[test_index] = __lb_run_test(
ndev, (enum hnae_loop)st_param[i][0]);
- (void)__lb_down(ndev);
+ (void)__lb_down(ndev,
+ (enum hnae_loop)st_param[i][0]);
}
if (data[test_index])
--
1.9.1
next prev parent reply other threads:[~2017-06-26 1:40 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-26 2:10 [PATCH NET V5 0/2] Add loopback support in phy_driver and hns ethtool fix Lin Yun Sheng
2017-06-26 2:10 ` [PATCH NET V5 1/2] net: phy: Add phy loopback support in net phy framework Lin Yun Sheng
2017-06-26 13:43 ` Andrew Lunn
2017-06-26 16:45 ` Florian Fainelli
2017-06-26 2:10 ` Lin Yun Sheng [this message]
2017-06-26 13:42 ` [PATCH NET V5 2/2] net: hns: Use phy_driver to setup Phy loopback Andrew Lunn
2017-06-27 3:25 ` Yunsheng Lin
2017-06-27 13:29 ` Andrew Lunn
2017-06-28 0:59 ` Yunsheng Lin
2017-06-28 20:28 ` Andrew Lunn
2017-06-29 2:35 ` Yunsheng Lin
2017-06-29 13:56 ` Andrew Lunn
2017-06-30 9:14 ` Yunsheng Lin
2017-06-30 13:39 ` Andrew Lunn
2017-07-01 15:17 ` Andrew Lunn
2017-07-03 9:57 ` Yunsheng Lin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1498443039-134503-3-git-send-email-linyunsheng@huawei.com \
--to=linyunsheng@huawei.com \
--cc=Yisen.Zhuang@huawei.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=gabriele.paoloni@huawei.com \
--cc=huangdaode@hisilicon.com \
--cc=john.garry@huawei.com \
--cc=liguozhu@hisilicon.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxarm@huawei.com \
--cc=lipeng321@huawei.com \
--cc=netdev@vger.kernel.org \
--cc=salil.mehta@huawei.com \
--cc=tremyfr@gmail.com \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).