From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1756232AbdLVNbw (ORCPT ); Fri, 22 Dec 2017 08:31:52 -0500 Received: from lelnx194.ext.ti.com ([198.47.27.80]:49172 "EHLO lelnx194.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755982AbdLVNbU (ORCPT ); Fri, 22 Dec 2017 08:31:20 -0500 From: Faiz Abbas To: , , , CC: , , , , , , , , , Subject: [PATCH v6 4/6] can: m_can: Support higher speed CAN-FD bitrates Date: Fri, 22 Dec 2017 19:01:26 +0530 Message-ID: <1513949488-13026-5-git-send-email-faiz_abbas@ti.com> X-Mailer: git-send-email 2.7.4 In-Reply-To: <1513949488-13026-1-git-send-email-faiz_abbas@ti.com> References: <1513949488-13026-1-git-send-email-faiz_abbas@ti.com> MIME-Version: 1.0 Content-Type: text/plain X-EXCLAIMER-MD-CONFIG: e1e8a2fd-e40a-4ac6-ac9b-f7e9cc9ee180 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org From: Franklin S Cooper Jr During test transmitting using CAN-FD at high bitrates (> 2 Mbps) would fail. Scoping the signals I noticed that only a single bit was being transmitted and with a bit more investigation realized the actual MCAN IP would go back to initialization mode automatically. It appears this issue is due to the MCAN needing to use the Transmitter Delay Compensation Mode with the correct value for the transmitter delay compensation offset (tdco). What impacts the tdco value isn't 100% clear but to calculate it you use an equation defined in the MCAN User's Guide. The user guide mentions that this register needs to be set based on clock values, secondary sample point and the data bitrate. One of the key variables that can't automatically be determined is the secondary sample point (ssp). This ssp is similar to the sp but is specific to this transmitter delay compensation mode. The guidelines for configuring ssp is rather vague but via some CAN test it appears for DRA76x that putting the value same as data sampling point works. The CAN-CIA's "Bit Time Requirements for CAN FD" paper presented at the International CAN Conference 2013 indicates that this TDC mode is only needed for data bit rates above 2.5 Mbps. Therefore, only enable this mode when the data bit rate is above 2.5 Mbps. Signed-off-by: Franklin S Cooper Jr Signed-off-by: Sekhar Nori Signed-off-by: Faiz Abbas --- drivers/net/can/m_can/m_can.c | 41 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 40 insertions(+), 1 deletion(-) diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c index 53e764f..371ffc1 100644 --- a/drivers/net/can/m_can/m_can.c +++ b/drivers/net/can/m_can/m_can.c @@ -127,6 +127,12 @@ enum m_can_mram_cfg { #define DBTP_DSJW_SHIFT 0 #define DBTP_DSJW_MASK (0xf << DBTP_DSJW_SHIFT) +/* Transmitter Delay Compensation Register (TDCR) */ +#define TDCR_TDCO_SHIFT 8 +#define TDCR_TDCO_MASK (0x7F << TDCR_TDCO_SHIFT) +#define TDCR_TDCF_SHIFT 0 +#define TDCR_TDCF_MASK (0x7F << TDCR_TDCF_SHIFT) + /* Test Register (TEST) */ #define TEST_LBCK BIT(4) @@ -991,7 +997,8 @@ static int m_can_set_bittiming(struct net_device *dev) const struct can_bittiming *bt = &priv->can.bittiming; const struct can_bittiming *dbt = &priv->can.data_bittiming; u16 brp, sjw, tseg1, tseg2; - u32 reg_btp; + u32 reg_btp, tdco, ssp; + bool enable_tdc = false; brp = bt->brp - 1; sjw = bt->sjw - 1; @@ -1006,9 +1013,41 @@ static int m_can_set_bittiming(struct net_device *dev) sjw = dbt->sjw - 1; tseg1 = dbt->prop_seg + dbt->phase_seg1 - 1; tseg2 = dbt->phase_seg2 - 1; + + /* TDC is only needed for bitrates beyond 2.5 MBit/s. + * This is mentioned in the "Bit Time Requirements for CAN FD" + * paper presented at the International CAN Conference 2013 + */ + if (dbt->bitrate > 2500000) { + /* Use the same value of secondary sampling point + * as the data sampling point + */ + ssp = dbt->sample_point; + + /* Equation based on Bosch's M_CAN User Manual's + * Transmitter Delay Compensation Section + */ + tdco = (priv->can.clock.freq / 1000) * + ssp / dbt->bitrate; + + /* Max valid TDCO value is 127 */ + if (tdco > 127) { + netdev_warn(dev, "TDCO value of %u is beyond maximum limit. Disabling Transmitter Delay Compensation mode\n", + tdco); + } else { + enable_tdc = true; + m_can_write(priv, M_CAN_TDCR, + tdco << TDCR_TDCO_SHIFT); + } + } + reg_btp = (brp << DBTP_DBRP_SHIFT) | (sjw << DBTP_DSJW_SHIFT) | (tseg1 << DBTP_DTSEG1_SHIFT) | (tseg2 << DBTP_DTSEG2_SHIFT); + + if (enable_tdc) + reg_btp |= DBTP_TDC; + m_can_write(priv, M_CAN_DBTP, reg_btp); } -- 2.7.4