MT8183 is a SoC based on 64bit ARMv8 architecture. It contains 4 CA53 and 4 CA73 cores. MT8183 share many HW IP with MT65xx series. This patchset was tested on MT8183 evaluation board, and boot to shell ok. This series contains document bindings, device tree including interrupt, uart. Change in v3: 1. Fill out GICC, GICH, GICV regions 2. Update Copyright to 2018 Change in v2: 1. Split dt-bindings into different patches 2. Correct bindings for supported SoCs (mtk-uart.txt) Ben Ho (1): arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile Erin Lo (3): dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183 dt-bindings: serial: Add compatible for Mediatek MT8183 Documentation/devicetree/bindings/arm/mediatek.txt | 4 + .../interrupt-controller/mediatek,sysirq.txt | 1 + .../devicetree/bindings/serial/mtk-uart.txt | 1 + arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 31 ++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 182 +++++++++++++++++++++ 6 files changed, 220 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-evb.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8183.dtsi -- 1.9.1
This adds dt-binding documentation of cpu for Mediatek MT8183. Signed-off-by: Erin Lo <erin.lo@mediatek.com> --- Documentation/devicetree/bindings/arm/mediatek.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 7d21ab3..2754535 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -19,6 +19,7 @@ compatible: Must contain one of "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" + "mediatek,mt8183" Supported boards: @@ -73,3 +74,6 @@ Supported boards: - MTK mt8173 tablet EVB: Required root node properties: - compatible = "mediatek,mt8173-evb", "mediatek,mt8173"; +- Evaluation board for MT8183: + Required root node properties: + - compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; -- 1.9.1
This adds dt-binding documentation of SYSIRQ for Mediatek MT8183 SoC Platform. Signed-off-by: Erin Lo <erin.lo@mediatek.com> --- .../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt index 07bf0b9..5ff48a8 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt @@ -5,6 +5,7 @@ interrupt. Required properties: - compatible: should be + "mediatek,mt8183-sysirq", "mediatek,mt6577-sysirq": for MT8183 "mediatek,mt8173-sysirq", "mediatek,mt6577-sysirq": for MT8173 "mediatek,mt8135-sysirq", "mediatek,mt6577-sysirq": for MT8135 "mediatek,mt8127-sysirq", "mediatek,mt6577-sysirq": for MT8127 -- 1.9.1
This adds dt-binding documentation of uart for Mediatek MT8183 SoC Platform. Signed-off-by: Erin Lo <erin.lo@mediatek.com> --- Documentation/devicetree/bindings/serial/mtk-uart.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index f73abff..4783336 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -15,6 +15,7 @@ Required properties: * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS + * "mediatek,mt8183-uart", "mediatek,mt6577-uart" for MT8183 compatible UARTS * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. -- 1.9.1
From: Ben Ho <Ben.Ho@mediatek.com> Add basic chip support for Mediatek 8183 Signed-off-by: Ben Ho <Ben.Ho@mediatek.com> Signed-off-by: Erin Lo <erin.lo@mediatek.com> --- arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 31 +++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 182 ++++++++++++++++++++++++++++ 3 files changed, 214 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-evb.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8183.dtsi diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index ac17f60..2836261 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -5,3 +5,4 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts new file mode 100644 index 0000000..9b52559 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts @@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + * Author: Ben Ho <ben.ho@mediatek.com> + * Erin Lo <erin.lo@mediatek.com> + */ + +/dts-v1/; +#include "mt8183.dtsi" + +/ { + model = "MediaTek MT8183 evaluation board"; + compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; + + aliases { + serial0 = &uart0; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x80000000>; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; +}; + +&uart0 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi new file mode 100644 index 0000000..03edf9c --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -0,0 +1,182 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + * Author: Ben Ho <ben.ho@mediatek.com> + * Erin Lo <erin.lo@mediatek.com> + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + compatible = "mediatek,mt8183"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu4>; + }; + core1 { + cpu = <&cpu5>; + }; + core2 { + cpu = <&cpu6>; + }; + core3 { + cpu = <&cpu7>; + }; + }; + }; + + cpu0: cpu@000 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x000>; + enable-method = "psci"; + }; + + cpu1: cpu@001 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x001>; + enable-method = "psci"; + }; + + cpu2: cpu@002 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x002>; + enable-method = "psci"; + }; + + cpu3: cpu@003 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x003>; + enable-method = "psci"; + }; + + cpu4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x100>; + enable-method = "psci"; + }; + + cpu5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x101>; + enable-method = "psci"; + }; + + cpu6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x102>; + enable-method = "psci"; + }; + + cpu7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x103>; + enable-method = "psci"; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + uart_clk: dummy26m { + compatible = "fixed-clock"; + clock-frequency = <26000000>; + #clock-cells = <0>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + }; + + gic: interrupt-controller@0c000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x0c000000 0 0x40000>, /* GICD */ + <0 0x0c100000 0 0x200000>; /* GICR */ + <0 0x0c400000 0 0x2000>; /* GICC */ + <0 0x0c410000 0 0x1000>; /* GICH */ + <0 0x0c420000 0 0x2000>; /* GICV */ + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + sysirq: intpol-controller@0c530a80 { + compatible = "mediatek,mt8183-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x0c530a80 0 0x50>; + }; + + uart0: serial@11002000 { + compatible = "mediatek,mt8183-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x1000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>, <&uart_clk>; + clock-names = "baud", "bus"; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt8183-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x1000>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>, <&uart_clk>; + clock-names = "baud", "bus"; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt8183-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x1000>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>; + clocks = <&uart_clk>, <&uart_clk>; + clock-names = "baud", "bus"; + status = "disabled"; + }; +}; -- 1.9.1
[-- Attachment #1: Type: text/plain, Size: 1108 bytes --] Hi Ben, Thank you for the patch! Yet something to improve: [auto build test ERROR on robh/for-next] [also build test ERROR on v4.17-rc5 next-20180517] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system] url: https://github.com/0day-ci/linux/commits/Erin-Lo/Add-basic-support-for-Mediatek-MT8183-SoC/20180519-160349 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm64-alldefconfig (attached as .config) compiler: aarch64-linux-gnu-gcc (Debian 7.2.0-11) 7.2.0 reproduce: wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree make.cross ARCH=arm64 All errors (new ones prefixed by >>): >> Error: arch/arm64/boot/dts/mediatek/mt8183.dtsi:137.9-10 syntax error FATAL ERROR: Unable to parse input tree --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 8591 bytes --]
On Thu, May 17, 2018 at 02:22:03PM +0800, Erin Lo wrote:
> This adds dt-binding documentation of cpu for Mediatek MT8183.
>
> Signed-off-by: Erin Lo <erin.lo@mediatek.com>
> ---
> Documentation/devicetree/bindings/arm/mediatek.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Reviewed-by: Rob Herring <robh@kernel.org>
On Thu, May 17, 2018 at 02:22:04PM +0800, Erin Lo wrote:
> This adds dt-binding documentation of SYSIRQ for Mediatek MT8183 SoC
> Platform.
>
> Signed-off-by: Erin Lo <erin.lo@mediatek.com>
> ---
> .../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh@kernel.org>
On Thu, May 17, 2018 at 02:22:05PM +0800, Erin Lo wrote:
> This adds dt-binding documentation of uart for Mediatek MT8183 SoC
> Platform.
>
> Signed-off-by: Erin Lo <erin.lo@mediatek.com>
> ---
> Documentation/devicetree/bindings/serial/mtk-uart.txt | 1 +
> 1 file changed, 1 insertion(+)
Acked-by: Rob Herring <robh@kernel.org>
Hi Erin,
On 17/05/18 08:22, Erin Lo wrote:
> MT8183 is a SoC based on 64bit ARMv8 architecture.
> It contains 4 CA53 and 4 CA73 cores.
> MT8183 share many HW IP with MT65xx series.
> This patchset was tested on MT8183 evaluation board, and boot to shell ok.
>
> This series contains document bindings, device tree including interrupt, uart.
>
> Change in v3:
> 1. Fill out GICC, GICH, GICV regions
> 2. Update Copyright to 2018
>
> Change in v2:
> 1. Split dt-bindings into different patches
> 2. Correct bindings for supported SoCs (mtk-uart.txt)
>
> Ben Ho (1):
> arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and
> Makefile
>
> Erin Lo (3):
> dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform
> dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183
> dt-bindings: serial: Add compatible for Mediatek MT8183
>
I'm a bit reluctant to take this series, as it will only enable the EVB board to
boot into a serial console. Are you planning to add support for other devices of
this SoC?
Apart please take into account that there is an issue with the dts file, as you
were told by the kbuild test robot.
Regards,
Matthias
On Mon, 2018-07-16 at 11:28 +0200, Matthias Brugger wrote: > Hi Erin, > > On 17/05/18 08:22, Erin Lo wrote: > > MT8183 is a SoC based on 64bit ARMv8 architecture. > > It contains 4 CA53 and 4 CA73 cores. > > MT8183 share many HW IP with MT65xx series. > > This patchset was tested on MT8183 evaluation board, and boot to shell ok. > > > > This series contains document bindings, device tree including interrupt, uart. > > > > Change in v3: > > 1. Fill out GICC, GICH, GICV regions > > 2. Update Copyright to 2018 > > > > Change in v2: > > 1. Split dt-bindings into different patches > > 2. Correct bindings for supported SoCs (mtk-uart.txt) > > > > Ben Ho (1): > > arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and > > Makefile > > > > Erin Lo (3): > > dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform > > dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183 > > dt-bindings: serial: Add compatible for Mediatek MT8183 > > > > I'm a bit reluctant to take this series, as it will only enable the EVB board to > boot into a serial console. Are you planning to add support for other devices of > this SoC? > > Apart please take into account that there is an issue with the dts file, as you > were told by the kbuild test robot. > > Regards, > Matthias > Hi, Matthias Sorry for missing this letter...since mail proxy server. We plan to add support all the devices of MT8183 in serious. We have implemented the clock and pinctrl driver for upstream and they are in internal review right now. About the dts issue... do you suggest me to send new patch right now or wait for clock and pinctrl driver ready then send them together? Best Regards, Erin > _______________________________________________ > Linux-mediatek mailing list > Linux-mediatek@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-mediatek
On 20/07/18 10:19, Erin Lo wrote: > On Mon, 2018-07-16 at 11:28 +0200, Matthias Brugger wrote: >> Hi Erin, >> >> On 17/05/18 08:22, Erin Lo wrote: >>> MT8183 is a SoC based on 64bit ARMv8 architecture. >>> It contains 4 CA53 and 4 CA73 cores. >>> MT8183 share many HW IP with MT65xx series. >>> This patchset was tested on MT8183 evaluation board, and boot to shell ok. >>> >>> This series contains document bindings, device tree including interrupt, uart. >>> >>> Change in v3: >>> 1. Fill out GICC, GICH, GICV regions >>> 2. Update Copyright to 2018 >>> >>> Change in v2: >>> 1. Split dt-bindings into different patches >>> 2. Correct bindings for supported SoCs (mtk-uart.txt) >>> >>> Ben Ho (1): >>> arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and >>> Makefile >>> >>> Erin Lo (3): >>> dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform >>> dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183 >>> dt-bindings: serial: Add compatible for Mediatek MT8183 >>> >> >> I'm a bit reluctant to take this series, as it will only enable the EVB board to >> boot into a serial console. Are you planning to add support for other devices of >> this SoC? >> >> Apart please take into account that there is an issue with the dts file, as you >> were told by the kbuild test robot. >> >> Regards, >> Matthias >> > > Hi, Matthias > Sorry for missing this letter...since mail proxy server. > We plan to add support all the devices of MT8183 in serious. > We have implemented the clock and pinctrl driver for upstream and they > are in internal review right now. > Nice to hear that :) > About the dts issue... do you suggest me to send new patch right now or > wait for clock and pinctrl driver ready then send them together? > I would prefer that you send at least the clock controller together, so that we don't have any dummy clocks in the basic device tree. Regards, Matthias
On Fri, 2018-07-20 at 12:44 +0200, Matthias Brugger wrote: > > On 20/07/18 10:19, Erin Lo wrote: > > On Mon, 2018-07-16 at 11:28 +0200, Matthias Brugger wrote: > >> Hi Erin, > >> > >> On 17/05/18 08:22, Erin Lo wrote: > >>> MT8183 is a SoC based on 64bit ARMv8 architecture. > >>> It contains 4 CA53 and 4 CA73 cores. > >>> MT8183 share many HW IP with MT65xx series. > >>> This patchset was tested on MT8183 evaluation board, and boot to shell ok. > >>> > >>> This series contains document bindings, device tree including interrupt, uart. > >>> > >>> Change in v3: > >>> 1. Fill out GICC, GICH, GICV regions > >>> 2. Update Copyright to 2018 > >>> > >>> Change in v2: > >>> 1. Split dt-bindings into different patches > >>> 2. Correct bindings for supported SoCs (mtk-uart.txt) > >>> > >>> Ben Ho (1): > >>> arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and > >>> Makefile > >>> > >>> Erin Lo (3): > >>> dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform > >>> dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183 > >>> dt-bindings: serial: Add compatible for Mediatek MT8183 > >>> > >> > >> I'm a bit reluctant to take this series, as it will only enable the EVB board to > >> boot into a serial console. Are you planning to add support for other devices of > >> this SoC? > >> > >> Apart please take into account that there is an issue with the dts file, as you > >> were told by the kbuild test robot. > >> > >> Regards, > >> Matthias > >> > > > > Hi, Matthias > > Sorry for missing this letter...since mail proxy server. > > We plan to add support all the devices of MT8183 in serious. > > We have implemented the clock and pinctrl driver for upstream and they > > are in internal review right now. > > > > Nice to hear that :) > > > About the dts issue... do you suggest me to send new patch right now or > > wait for clock and pinctrl driver ready then send them together? > > > > I would prefer that you send at least the clock controller together, so that we > don't have any dummy clocks in the basic device tree. > > Regards, > Matthias > Got it! Next patch, we will send them with clock controller without dummy clocks in the basic device tree. By the way, the clock controller driver of MT8183 is a little bit different from former ICs, so we need more time to prepare them. We will send them to public as soon as possible. Best Regards, Erin > _______________________________________________ > Linux-mediatek mailing list > Linux-mediatek@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-mediatek
On 21/07/18 09:28, Erin Lo wrote:
> On Fri, 2018-07-20 at 12:44 +0200, Matthias Brugger wrote:
>>
>> On 20/07/18 10:19, Erin Lo wrote:
>>> On Mon, 2018-07-16 at 11:28 +0200, Matthias Brugger wrote:
>>>> Hi Erin,
>>>>
>>>> On 17/05/18 08:22, Erin Lo wrote:
>>>>> MT8183 is a SoC based on 64bit ARMv8 architecture.
>>>>> It contains 4 CA53 and 4 CA73 cores.
>>>>> MT8183 share many HW IP with MT65xx series.
>>>>> This patchset was tested on MT8183 evaluation board, and boot to shell ok.
>>>>>
>>>>> This series contains document bindings, device tree including interrupt, uart.
>>>>>
>>>>> Change in v3:
>>>>> 1. Fill out GICC, GICH, GICV regions
>>>>> 2. Update Copyright to 2018
>>>>>
>>>>> Change in v2:
>>>>> 1. Split dt-bindings into different patches
>>>>> 2. Correct bindings for supported SoCs (mtk-uart.txt)
>>>>>
>>>>> Ben Ho (1):
>>>>> arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and
>>>>> Makefile
>>>>>
>>>>> Erin Lo (3):
>>>>> dt-bindings: arm: Add bindings for Mediatek MT8183 SoC Platform
>>>>> dt-bindings: mtk-sysirq: Add compatible for Mediatek MT8183
>>>>> dt-bindings: serial: Add compatible for Mediatek MT8183
>>>>>
>>>>
>>>> I'm a bit reluctant to take this series, as it will only enable the EVB board to
>>>> boot into a serial console. Are you planning to add support for other devices of
>>>> this SoC?
>>>>
>>>> Apart please take into account that there is an issue with the dts file, as you
>>>> were told by the kbuild test robot.
>>>>
>>>> Regards,
>>>> Matthias
>>>>
>>>
>>> Hi, Matthias
>>> Sorry for missing this letter...since mail proxy server.
>>> We plan to add support all the devices of MT8183 in serious.
>>> We have implemented the clock and pinctrl driver for upstream and they
>>> are in internal review right now.
>>>
>>
>> Nice to hear that :)
>>
>>> About the dts issue... do you suggest me to send new patch right now or
>>> wait for clock and pinctrl driver ready then send them together?
>>>
>>
>> I would prefer that you send at least the clock controller together, so that we
>> don't have any dummy clocks in the basic device tree.
>>
>> Regards,
>> Matthias
>>
>
> Got it! Next patch, we will send them with clock controller without
> dummy clocks in the basic device tree.
> By the way, the clock controller driver of MT8183 is a little bit
> different from former ICs, so we need more time to prepare them.
> We will send them to public as soon as possible.
>
Thanks for the info.
Best regards,
Matthias