From: Eddie James <eajames@linux.ibm.com>
To: linux-kernel@vger.kernel.org
Cc: linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org,
jdelvare@suse.com, linux-doc@vger.kernel.org,
gregkh@linuxfoundation.org, robh+dt@kernel.org,
mark.rutland@arm.com, linux@roeck-us.net, rdunlap@infradead.org,
benh@kernel.crashing.org,
Eddie James <eajames@linux.vnet.ibm.com>,
Eddie James <eajames@linux.ibm.com>
Subject: [PATCH v6 03/10] Documentation: hwmon: Add OCC documentation
Date: Thu, 8 Nov 2018 15:05:22 -0600 [thread overview]
Message-ID: <1541711129-26631-4-git-send-email-eajames@linux.ibm.com> (raw)
In-Reply-To: <1541711129-26631-1-git-send-email-eajames@linux.ibm.com>
From: Eddie James <eajames@linux.vnet.ibm.com>
Document the hwmon interface for the OCC.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
Documentation/hwmon/occ | 112 ++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)
create mode 100644 Documentation/hwmon/occ
diff --git a/Documentation/hwmon/occ b/Documentation/hwmon/occ
new file mode 100644
index 0000000..e787596
--- /dev/null
+++ b/Documentation/hwmon/occ
@@ -0,0 +1,112 @@
+Kernel driver occ-hwmon
+=======================
+
+Supported chips:
+ * POWER8
+ * POWER9
+
+Author: Eddie James <eajames@linux.ibm.com>
+
+Description
+-----------
+
+This driver supports hardware monitoring for the On-Chip Controller (OCC)
+embedded on POWER processors. The OCC is a device that collects and aggregates
+sensor data from the processor and the system. The OCC can provide the raw
+sensor data as well as perform thermal and power management on the system.
+
+The P8 version of this driver is a client driver of I2C. It may be probed
+manually if an "ibm,p8-occ-hwmon" compatible device is found under the
+appropriate I2C bus node in the device-tree.
+
+The P9 version of this driver is a client driver of the FSI-based OCC driver.
+It will be probed automatically by the FSI-based OCC driver.
+
+Sysfs entries
+-------------
+
+The following attributes are supported. All attributes are read-only unless
+specified.
+
+The OCC sensor ID is an integer that represents the unique identifier of the
+sensor with respect to the OCC. For example, a temperature sensor for the third
+DIMM slot in the system may have a sensor ID of 7. This mapping is unavailable
+to the device driver, which must therefore export the sensor ID as-is.
+
+Some entries are only present with certain OCC sensor versions or only on
+certain OCCs in the system. The version number is not exported to the user
+but can be inferred.
+
+temp[1-n]_label OCC sensor ID.
+[with temperature sensor version 1]
+ temp[1-n]_input Measured temperature of the component in millidegrees
+ Celsius.
+[with temperature sensor version >= 2]
+ temp[1-n]_type The FRU (Field Replaceable Unit) type
+ (represented by an integer) for the component
+ that this sensor measures.
+ temp[1-n]_fault Temperature sensor fault boolean; 1 to indicate
+ that a fault is present or 0 to indicate that
+ no fault is present.
+ [with type == 3 (FRU type is VRM)]
+ temp[1-n]_alarm VRM temperature alarm boolean; 1 to indicate
+ alarm, 0 to indicate no alarm
+ [else]
+ temp[1-n]_input Measured temperature of the component in
+ millidegrees Celsius.
+
+freq[1-n]_label OCC sensor ID.
+freq[1-n]_input Measured frequency of the component in MHz.
+
+power[1-n]_input Latest measured power reading of the component in
+ microwatts.
+power[1-n]_average Average power of the component in microwatts.
+power[1-n]_average_interval The amount of time over which the power average
+ was taken in microseconds.
+[with power sensor version < 2]
+ power[1-n]_label OCC sensor ID.
+[with power sensor version >= 2]
+ power[1-n]_label OCC sensor ID + function ID + channel in the form
+ of a string, delimited by underscores, i.e. "0_15_1".
+ Both the function ID and channel are integers that
+ further identify the power sensor.
+[with power sensor version 0xa0]
+ power[1-n]_label OCC sensor ID + sensor type in the form of a string,
+ delimited by an underscore, i.e. "0_system". Sensor
+ type will be one of "system", "proc", "vdd" or "vdn".
+ For this sensor version, OCC sensor ID will be the same
+ for all power sensors.
+[present only on "master" OCC; represents the whole system power; only one of
+ this type of power sensor will be present]
+ power[1-n]_label "system"
+ power[1-n]_input Latest system output power in microwatts.
+ power[1-n]_cap Current system power cap in microwatts.
+ power[1-n]_cap_not_redundant System power cap in microwatts when
+ there is not redundant power.
+ power[1-n]_cap_max Maximum power cap that the OCC can enforce in
+ microwatts.
+ power[1-n]_cap_min Minimum power cap that the OCC can enforce in
+ microwatts.
+ power[1-n]_cap_user The power cap set by the user, in microwatts.
+ This attribute will return 0 if no user power
+ cap has been set. This attribute is read-write,
+ but writing any precision below watts will be
+ ignored, i.e. requesting a power cap of
+ 500900000 microwatts will result in a power cap
+ request of 500 watts.
+ [with caps sensor version > 1]
+ power[1-n]_cap_user_source Indicates how the user power cap was
+ set. This is an integer that maps to
+ system or firmware components that can
+ set the user power cap.
+
+The following "extn" sensors are exported as a way for the OCC to provide data
+that doesn't fit anywhere else. The meaning of these sensors is entirely
+dependent on their data, and cannot be statically defined.
+
+extn[1-n]_label ASCII ID or OCC sensor ID.
+extn[1-n]_flags This is one byte hexadecimal value. Bit 7 indicates the
+ type of the label attribute; 1 for sensor ID, 0 for
+ ASCII ID. Other bits are reserved.
+extn[1-n]_input 6 bytes of hexadecimal data, with a meaning defined by
+ the sensor ID.
--
1.8.3.1
next prev parent reply other threads:[~2018-11-08 21:06 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-08 21:05 [PATCH v6 00/10] hwmon and fsi: Add On-Chip Controller Driver Eddie James
2018-11-08 21:05 ` [PATCH v6 01/10] dt-bindings: fsi: Add P9 OCC device documentation Eddie James
2018-11-08 21:05 ` [PATCH v6 02/10] fsi: Add On-Chip Controller (OCC) driver Eddie James
2018-11-08 21:05 ` Eddie James [this message]
2018-11-08 21:05 ` [PATCH v6 04/10] dt-bindings: i2c: Add P8 OCC hwmon device documentation Eddie James
2018-11-08 21:05 ` [PATCH v6 05/10] hwmon: Add On-Chip Controller (OCC) hwmon driver Eddie James
2018-11-08 21:05 ` [PATCH v6 06/10] hwmon (occ): Add command transport method for P8 and P9 Eddie James
2018-11-08 21:05 ` [PATCH v6 07/10] hwmon (occ): Parse OCC poll response Eddie James
2018-11-08 21:05 ` [PATCH v6 08/10] hwmon (occ): Add sensor types and versions Eddie James
2018-11-08 21:05 ` [PATCH v6 09/10] hwmon (occ): Add sensor attributes and register hwmon device Eddie James
2018-11-08 21:05 ` [PATCH v6 10/10] hwmon (occ): Add sysfs attributes for additional OCC data Eddie James
2018-11-09 23:03 ` [PATCH v6 00/10] hwmon and fsi: Add On-Chip Controller Driver Guenter Roeck
2018-11-12 16:25 ` Eddie James
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1541711129-26631-4-git-send-email-eajames@linux.ibm.com \
--to=eajames@linux.ibm.com \
--cc=benh@kernel.crashing.org \
--cc=devicetree@vger.kernel.org \
--cc=eajames@linux.vnet.ibm.com \
--cc=gregkh@linuxfoundation.org \
--cc=jdelvare@suse.com \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=mark.rutland@arm.com \
--cc=rdunlap@infradead.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).