linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices
@ 2018-11-14 14:47 Bharat Kumar Gogada
  2018-12-06 15:47 ` Bharat Kumar Gogada
  2019-02-02  0:41 ` Bjorn Helgaas
  0 siblings, 2 replies; 3+ messages in thread
From: Bharat Kumar Gogada @ 2018-11-14 14:47 UTC (permalink / raw)
  To: linux-pci, linux-kernel; +Cc: bhelgaas, rgummal, Bharat Kumar Gogada

As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages
will be forwarded from the secondary interface to the primary interface,
if the SERR# Enable bit in the Bridge Control register is set.
Currently PCI_BRIDGE_CTL_SERR is being enabled only in
ACPI flow.
This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device.

Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
---
 drivers/pci/probe.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index b1c05b5..ed71e8e 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp)
 		pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER,
 				      hpp->latency_timer);
 		pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl);
-		if (hpp->enable_serr)
-			pci_bctl |= PCI_BRIDGE_CTL_SERR;
 		if (hpp->enable_perr)
 			pci_bctl |= PCI_BRIDGE_CTL_PARITY;
 		pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl);
@@ -2114,6 +2112,23 @@ static void pci_configure_eetlp_prefix(struct pci_dev *dev)
 #endif
 }
 
+static void pci_configure_serr(struct pci_dev *dev)
+{
+	if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) {
+		u16 control;
+
+		/*
+		 * A Type-1 PCI bridge will not forward ERR_ messages coming
+		 * from an endpoint if SERR# forwarding is not enabled.
+		 */
+		pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &control);
+		if (!(control & PCI_BRIDGE_CTL_SERR)) {
+			control |= PCI_BRIDGE_CTL_SERR;
+			pci_write_config_word(dev, PCI_BRIDGE_CONTROL, control);
+		}
+	}
+}
+
 static void pci_configure_device(struct pci_dev *dev)
 {
 	struct hotplug_params hpp;
@@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev *dev)
 	pci_configure_relaxed_ordering(dev);
 	pci_configure_ltr(dev);
 	pci_configure_eetlp_prefix(dev);
+	pci_configure_serr(dev);
 
 	memset(&hpp, 0, sizeof(hpp));
 	ret = pci_get_hp_params(dev, &hpp);
-- 
2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* RE: [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices
  2018-11-14 14:47 [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices Bharat Kumar Gogada
@ 2018-12-06 15:47 ` Bharat Kumar Gogada
  2019-02-02  0:41 ` Bjorn Helgaas
  1 sibling, 0 replies; 3+ messages in thread
From: Bharat Kumar Gogada @ 2018-12-06 15:47 UTC (permalink / raw)
  To: Bharat Kumar Gogada, linux-pci, linux-kernel
  Cc: bhelgaas, Ravikiran Gummaluri

Hi All,

Please let me know if anyone has any issue with this patch.

Regards,
Bharat
> As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded
> from the secondary interface to the primary interface, if the SERR# Enable
> bit in the Bridge Control register is set.
> Currently PCI_BRIDGE_CTL_SERR is being enabled only in ACPI flow.
> This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device.
> 
> Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
> ---
>  drivers/pci/probe.c | 20 ++++++++++++++++++--
>  1 file changed, 18 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index
> b1c05b5..ed71e8e 100644
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev
> *dev, struct hpp_type0 *hpp)
>  		pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER,
>  				      hpp->latency_timer);
>  		pci_read_config_word(dev, PCI_BRIDGE_CONTROL,
> &pci_bctl);
> -		if (hpp->enable_serr)
> -			pci_bctl |= PCI_BRIDGE_CTL_SERR;
>  		if (hpp->enable_perr)
>  			pci_bctl |= PCI_BRIDGE_CTL_PARITY;
>  		pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> pci_bctl); @@ -2114,6 +2112,23 @@ static void
> pci_configure_eetlp_prefix(struct pci_dev *dev)  #endif  }
> 
> +static void pci_configure_serr(struct pci_dev *dev) {
> +	if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) {
> +		u16 control;
> +
> +		/*
> +		 * A Type-1 PCI bridge will not forward ERR_ messages
> coming
> +		 * from an endpoint if SERR# forwarding is not enabled.
> +		 */
> +		pci_read_config_word(dev, PCI_BRIDGE_CONTROL,
> &control);
> +		if (!(control & PCI_BRIDGE_CTL_SERR)) {
> +			control |= PCI_BRIDGE_CTL_SERR;
> +			pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> control);
> +		}
> +	}
> +}
> +
>  static void pci_configure_device(struct pci_dev *dev)  {
>  	struct hotplug_params hpp;
> @@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev
> *dev)
>  	pci_configure_relaxed_ordering(dev);
>  	pci_configure_ltr(dev);
>  	pci_configure_eetlp_prefix(dev);
> +	pci_configure_serr(dev);
> 
>  	memset(&hpp, 0, sizeof(hpp));
>  	ret = pci_get_hp_params(dev, &hpp);
> --
> 2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices
  2018-11-14 14:47 [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices Bharat Kumar Gogada
  2018-12-06 15:47 ` Bharat Kumar Gogada
@ 2019-02-02  0:41 ` Bjorn Helgaas
  1 sibling, 0 replies; 3+ messages in thread
From: Bjorn Helgaas @ 2019-02-02  0:41 UTC (permalink / raw)
  To: Bharat Kumar Gogada
  Cc: linux-pci, linux-kernel, Sinan Kaya, Timur Tabi, Jon Masters,
	Yijing Wang, Christopher Covington, Taku Izumi, Oza Pawandeep,
	Ravikiran Gummaluri

[+cc others who have commented or been copied on this ancient issue]

On Wed, Nov 14, 2018 at 08:17:01PM +0530, Bharat Kumar Gogada wrote:
> As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages
> will be forwarded from the secondary interface to the primary interface,
> if the SERR# Enable bit in the Bridge Control register is set.
> Currently PCI_BRIDGE_CTL_SERR is being enabled only in
> ACPI flow.
> This patch enables PCI_BRIDGE_CTL_SERR for Type-1 PCI device.

I apologize for being so slow to respond to this.

I applied it to pci/aer for v5.1 with the following changelog:

    PCI: Enable SERR# forwarding for all bridges
    
    As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded
    from the secondary interface to the primary interface, if the SERR# Enable
    bit in the Bridge Control register is set.
    
    It seems clear that an ACPI hotplug parameter method (_HPP or _HPX) that
    tells us to "enable SERR in the command register" (ACPI v6.2, sec 6.2.8,
    6.2.9.1) refers to PCI_COMMAND_SERR, which enables reporting of errors by
    the function itself.
    
    For bridges, we also interpreted that to mean we should enable
    PCI_BRIDGE_CTL_SERR, which enables *forwarding* of errors by the bridge.
    But we didn't enable PCI_BRIDGE_CTL_SERR anywhere else, which means we
    never enabled it for non-ACPI systems or ACPI systems that didn't supply
    hotplug parameters.
    
    That means errors reported below bridges were often never forwarded up to a
    Root Port where they could be signaled via AER.
    
    Enable PCI_BRIDGE_CTL_SERR for all bridges so we can get better error
    reporting for downstream devices.
    
    Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
    [bhelgaas: changelog]
    Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

> Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
> ---
>  drivers/pci/probe.c | 20 ++++++++++++++++++--
>  1 file changed, 18 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> index b1c05b5..ed71e8e 100644
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -1841,8 +1841,6 @@ static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp)
>  		pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER,
>  				      hpp->latency_timer);
>  		pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl);
> -		if (hpp->enable_serr)
> -			pci_bctl |= PCI_BRIDGE_CTL_SERR;
>  		if (hpp->enable_perr)
>  			pci_bctl |= PCI_BRIDGE_CTL_PARITY;
>  		pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl);
> @@ -2114,6 +2112,23 @@ static void pci_configure_eetlp_prefix(struct pci_dev *dev)
>  #endif
>  }
>  
> +static void pci_configure_serr(struct pci_dev *dev)
> +{
> +	if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE) {
> +		u16 control;
> +
> +		/*
> +		 * A Type-1 PCI bridge will not forward ERR_ messages coming
> +		 * from an endpoint if SERR# forwarding is not enabled.
> +		 */
> +		pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &control);
> +		if (!(control & PCI_BRIDGE_CTL_SERR)) {
> +			control |= PCI_BRIDGE_CTL_SERR;
> +			pci_write_config_word(dev, PCI_BRIDGE_CONTROL, control);
> +		}
> +	}
> +}
> +
>  static void pci_configure_device(struct pci_dev *dev)
>  {
>  	struct hotplug_params hpp;
> @@ -2124,6 +2139,7 @@ static void pci_configure_device(struct pci_dev *dev)
>  	pci_configure_relaxed_ordering(dev);
>  	pci_configure_ltr(dev);
>  	pci_configure_eetlp_prefix(dev);
> +	pci_configure_serr(dev);
>  
>  	memset(&hpp, 0, sizeof(hpp));
>  	ret = pci_get_hp_params(dev, &hpp);
> -- 
> 2.7.4
> 

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2019-02-02  0:42 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-14 14:47 [PATCH] PCI: Enable SERR# forwarding for Type-1 PCI devices Bharat Kumar Gogada
2018-12-06 15:47 ` Bharat Kumar Gogada
2019-02-02  0:41 ` Bjorn Helgaas

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).