From: Sowjanya Komatineni <skomatineni@nvidia.com>
To: <robh+dt@kernel.org>, <mark.rutland@arm.com>,
<mperttunen@nvidia.com>, <thierry.reding@gmail.com>,
<jonathanh@nvidia.com>, <adrian.hunter@intel.com>,
<ulf.hansson@linaro.org>
Cc: <devicetree@vger.kernel.org>, <linux-tegra@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
"Sowjanya Komatineni" <skomatineni@nvidia.com>
Subject: [PATCH V3 2/3] arm64: dts: tegra: Add SDMMC Auto-cal settings
Date: Wed, 2 Jan 2019 12:57:53 -0800 [thread overview]
Message-ID: <1546462674-22856-2-git-send-email-skomatineni@nvidia.com> (raw)
In-Reply-To: <1546462674-22856-1-git-send-email-skomatineni@nvidia.com>
Add SDMMC initial pad offsets used by auto calibration process.
Add SDMMC fixed drive strengths for Tegra210 and above which are
used when calibration timeouts.
Fixed drive strengths are based on Pre SI Analysis of the pads.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
---
arch/arm64/boot/dts/nvidia/tegra186.dtsi | 2 ++
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 34 +++++++++++++++++++
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 57 ++++++++++++++++++++++++++++++--
3 files changed, 91 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
index 2f3c8e29520d..0631bb9bfcc3 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
@@ -311,6 +311,8 @@
nvidia,pad-autocal-pull-down-offset-hs400 = <0x05>;
nvidia,pad-autocal-pull-up-offset-1v8-timeout = <0x0a>;
nvidia,pad-autocal-pull-down-offset-1v8-timeout = <0x0a>;
+ nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x0a>;
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout = <0x0a>;
nvidia,default-tap = <0x5>;
nvidia,default-trim = <0x9>;
nvidia,dqs-trim = <63>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
index c2091bb16546..3fab6802c335 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
@@ -301,6 +301,17 @@
clock-names = "sdhci";
resets = <&bpmp TEGRA194_RESET_SDMMC1>;
reset-names = "sdhci";
+ nvidia,pad-autocal-pull-up-offset-3v3-timeout =
+ <0x07>;
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout =
+ <0x07>;
+ nvidia,pad-autocal-pull-up-offset-1v8-timeout = <0x06>;
+ nvidia,pad-autocal-pull-down-offset-1v8-timeout =
+ <0x07>;
+ nvidia,pad-autocal-pull-up-offset-sdr104 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
+ nvidia,default-tap = <0x9>;
+ nvidia,default-trim = <0x5>;
status = "disabled";
};
@@ -312,6 +323,18 @@
clock-names = "sdhci";
resets = <&bpmp TEGRA194_RESET_SDMMC3>;
reset-names = "sdhci";
+ nvidia,pad-autocal-pull-up-offset-1v8 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-1v8 = <0x7a>;
+ nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x07>;
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout =
+ <0x07>;
+ nvidia,pad-autocal-pull-up-offset-1v8-timeout = <0x06>;
+ nvidia,pad-autocal-pull-down-offset-1v8-timeout =
+ <0x07>;
+ nvidia,pad-autocal-pull-up-offset-sdr104 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
+ nvidia,default-tap = <0x9>;
+ nvidia,default-trim = <0x5>;
status = "disabled";
};
@@ -323,6 +346,17 @@
clock-names = "sdhci";
resets = <&bpmp TEGRA194_RESET_SDMMC4>;
reset-names = "sdhci";
+ nvidia,pad-autocal-pull-up-offset-hs400 = <0x00>;
+ nvidia,pad-autocal-pull-down-offset-hs400 = <0x00>;
+ nvidia,pad-autocal-pull-up-offset-1v8-timeout = <0x0a>;
+ nvidia,pad-autocal-pull-down-offset-1v8-timeout =
+ <0x0a>;
+ nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x0a>;
+ nvidia,pad-autocal-pull-down-offset-3v3-timeout =
+ <0x0a>;
+ nvidia,default-tap = <0x8>;
+ nvidia,default-trim = <0x14>;
+ nvidia,dqs-trim = <40>;
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
index 2205d66b0443..41408df9d4e9 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
@@ -476,6 +476,48 @@
compatible = "nvidia,tegra210-pinmux";
reg = <0x0 0x700008d4 0x0 0x29c>, /* Pad control registers */
<0x0 0x70003000 0x0 0x294>; /* Mux registers */
+ sdmmc1_3v3_drv: sdmmc1-3v3-drv {
+ sdmmc1 {
+ nvidia,pins = "drive_sdmmc1";
+ nvidia,pull-down-strength = <0x8>;
+ nvidia,pull-up-strength = <0x8>;
+ };
+ };
+ sdmmc1_1v8_drv: sdmmc1-1v8-drv {
+ sdmmc1 {
+ nvidia,pins = "drive_sdmmc1";
+ nvidia,pull-down-strength = <0x4>;
+ nvidia,pull-up-strength = <0x3>;
+ };
+ };
+ sdmmc2_1v8_drv: sdmmc2-1v8-drv {
+ sdmmc2 {
+ nvidia,pins = "drive_sdmmc2";
+ nvidia,pull-down-strength = <0x10>;
+ nvidia,pull-up-strength = <0x10>;
+ };
+ };
+ sdmmc3_3v3_drv: sdmmc3-3v3-drv {
+ sdmmc3 {
+ nvidia,pins = "drive_sdmmc3";
+ nvidia,pull-down-strength = <0x8>;
+ nvidia,pull-up-strength = <0x8>;
+ };
+ };
+ sdmmc3_1v8_drv: sdmmc3-1v8-drv {
+ sdmmc3 {
+ nvidia,pins = "drive_sdmmc3";
+ nvidia,pull-down-strength = <0x4>;
+ nvidia,pull-up-strength = <0x3>;
+ };
+ };
+ sdmmc4_1v8_drv: sdmmc4-1v8-drv {
+ sdmmc4 {
+ nvidia,pins = "drive_sdmmc4";
+ nvidia,pull-down-strength = <0x10>;
+ nvidia,pull-up-strength = <0x10>;
+ };
+ };
};
/*
@@ -1050,9 +1092,12 @@
clock-names = "sdhci";
resets = <&tegra_car 14>;
reset-names = "sdhci";
- pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8",
+ "sdmmc-3v3-drv", "sdmmc-1v8-drv";
pinctrl-0 = <&sdmmc1_3v3>;
pinctrl-1 = <&sdmmc1_1v8>;
+ pinctrl-2 = <&sdmmc1_3v3_drv>;
+ pinctrl-3 = <&sdmmc1_1v8_drv>;
nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
@@ -1075,6 +1120,8 @@
clock-names = "sdhci";
resets = <&tegra_car 9>;
reset-names = "sdhci";
+ pinctrl-names = "sdmmc-1v8-drv";
+ pinctrl-0 = <&sdmmc2_1v8_drv>;
nvidia,pad-autocal-pull-up-offset-1v8 = <0x05>;
nvidia,pad-autocal-pull-down-offset-1v8 = <0x05>;
nvidia,default-tap = <0x8>;
@@ -1090,9 +1137,12 @@
clock-names = "sdhci";
resets = <&tegra_car 69>;
reset-names = "sdhci";
- pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+ pinctrl-names = "sdmmc-3v3", "sdmmc-1v8",
+ "sdmmc-3v3-drv", "sdmmc-1v8-drv";
pinctrl-0 = <&sdmmc3_3v3>;
pinctrl-1 = <&sdmmc3_1v8>;
+ pinctrl-2 = <&sdmmc3_3v3_drv>;
+ pinctrl-3 = <&sdmmc3_1v8_drv>;
nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
@@ -1110,6 +1160,9 @@
clock-names = "sdhci";
resets = <&tegra_car 15>;
reset-names = "sdhci";
+ pinctrl-names = "sdmmc-3v3-drv", "sdmmc-1v8-drv";
+ pinctrl-0 = <&sdmmc4_1v8_drv>;
+ pinctrl-1 = <&sdmmc4_1v8_drv>;
nvidia,pad-autocal-pull-up-offset-1v8 = <0x05>;
nvidia,pad-autocal-pull-down-offset-1v8 = <0x05>;
nvidia,default-tap = <0x8>;
--
2.7.4
next prev parent reply other threads:[~2019-01-02 20:58 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-02 20:57 [PATCH V3 1/3] dt-bindings: mmc: tegra: Add pinctrl for pad drive strength config Sowjanya Komatineni
2019-01-02 20:57 ` Sowjanya Komatineni [this message]
2019-01-02 20:57 ` [PATCH V3 3/3] mmc: tegra: SDMMC pads auto-calibration Sowjanya Komatineni
2019-01-10 15:06 ` Thierry Reding
2019-01-10 19:19 ` Sowjanya Komatineni
2019-01-10 14:48 ` [PATCH V3 1/3] dt-bindings: mmc: tegra: Add pinctrl for pad drive strength config Thierry Reding
2019-01-11 16:11 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1546462674-22856-2-git-send-email-skomatineni@nvidia.com \
--to=skomatineni@nvidia.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mperttunen@nvidia.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).