From: CK Hu <ck.hu@mediatek.com>
To: chunhui dai <chunhui.dai@mediatek.com>
Cc: --to=Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
"Philipp Zabel" <p.zabel@pengutronix.de>,
David Airlie <airlied@linux.ie>,
Sean Wang <sean.wang@mediatek.com>,
Ryder Lee <ryder.lee@mediatek.com>,
"Colin Ian King" <colin.king@canonical.com>,
<linux-clk@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<dri-devel@lists.freedesktop.org>, <srv_heupstream@mediatek.com>,
<bibby.hsieh@mediatek.com>, <jamesjj.liao@mediatek.com>,
<jitao.shi@mediatek.com>
Subject: Re: [PATCH 1/9] drm/mediatek: recalculate hdmi phy clock of MT2701 by querying hardware
Date: Thu, 10 Jan 2019 09:47:09 +0800 [thread overview]
Message-ID: <1547084829.27684.8.camel@mtksdaap41> (raw)
In-Reply-To: <1546585439-30455-2-git-send-email-chunhui.dai@mediatek.com>
Hi, Chunhui:
On Fri, 2019-01-04 at 15:03 +0800, chunhui dai wrote:
> Recalculate the rate of this clock, by querying hardware.
>
> Signed-off-by: chunhui dai <chunhui.dai@mediatek.com>
> ---
> drivers/gpu/drm/mediatek/mtk_hdmi_phy.c | 7 ++--
> drivers/gpu/drm/mediatek/mtk_hdmi_phy.h | 3 +-
> drivers/gpu/drm/mediatek/mtk_mt2701_hdmi_phy.c | 49 ++++++++++++++++++++++++++
> drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c | 8 +++++
> 4 files changed, 61 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_hdmi_phy.c
> index 4ef9c57..79e737d 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi_phy.c
> @@ -29,12 +29,11 @@ long mtk_hdmi_pll_round_rate(struct clk_hw *hw, unsigned long rate,
> return rate;
> }
>
> -unsigned long mtk_hdmi_pll_recalc_rate(struct clk_hw *hw,
> - unsigned long parent_rate)
> +u32 mtk_hdmi_phy_read(struct mtk_hdmi_phy *hdmi_phy, u32 offset)
> {
> - struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> + void __iomem *reg = hdmi_phy->regs + offset;
>
> - return hdmi_phy->pll_rate;
> + return readl(reg);
reg is used only once, so
return readl(hdmi_phy->regs + offset);
> }
>
> void mtk_hdmi_phy_clear_bits(struct mtk_hdmi_phy *hdmi_phy, u32 offset,
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi_phy.h b/drivers/gpu/drm/mediatek/mtk_hdmi_phy.h
> index f39b1fc..fdad8b1 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi_phy.h
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi_phy.h
> @@ -41,6 +41,7 @@ struct mtk_hdmi_phy {
> unsigned int ibias_up;
> };
>
> +u32 mtk_hdmi_phy_read(struct mtk_hdmi_phy *hdmi_phy, u32 offset);
> void mtk_hdmi_phy_clear_bits(struct mtk_hdmi_phy *hdmi_phy, u32 offset,
> u32 bits);
> void mtk_hdmi_phy_set_bits(struct mtk_hdmi_phy *hdmi_phy, u32 offset,
> @@ -50,8 +51,6 @@ void mtk_hdmi_phy_mask(struct mtk_hdmi_phy *hdmi_phy, u32 offset,
> struct mtk_hdmi_phy *to_mtk_hdmi_phy(struct clk_hw *hw);
> long mtk_hdmi_pll_round_rate(struct clk_hw *hw, unsigned long rate,
> unsigned long *parent_rate);
> -unsigned long mtk_hdmi_pll_recalc_rate(struct clk_hw *hw,
> - unsigned long parent_rate);
>
> extern struct platform_driver mtk_hdmi_phy_driver;
> extern struct mtk_hdmi_phy_conf mtk_hdmi_phy_8173_conf;
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt2701_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt2701_hdmi_phy.c
> index fcc42dc..b5ed6b7 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mt2701_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mt2701_hdmi_phy.c
> @@ -153,6 +153,55 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> RG_HDMITX_DRV_IBIAS_MASK);
> return 0;
> }
> +static unsigned long mtk_hdmi_pll_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> + unsigned long out_rate, val;
> +
> + val = (mtk_hdmi_phy_read(hdmi_phy, HDMI_CON6)
> + & RG_HTPLL_PREDIV_MASK) >> RG_HTPLL_PREDIV;
> + switch (val) {
> + case 0x00:
> + out_rate = parent_rate;
> + break;
> + case 0x01:
> + out_rate = parent_rate / 2;
> + break;
> + default:
> + out_rate = parent_rate / 4;
> + break;
If the val would not be 3, maybe out_rate could be calculate as
out_rate >>= val;
> + }
> +
> + val = (mtk_hdmi_phy_read(hdmi_phy, HDMI_CON6)
> + & RG_HTPLL_FBKDIV_MASK) >> RG_HTPLL_FBKDIV;
> + out_rate = out_rate * (val + 1) * 2;
out_rate *= (val + 1) * 2;
> + val = (mtk_hdmi_phy_read(hdmi_phy, HDMI_CON2)
> + & RG_HDMITX_TX_POSDIV_MASK) >> RG_HDMITX_TX_POSDIV;
> + switch (val) {
> + case 0x00:
> + out_rate = out_rate;
> + break;
> + case 0x01:
> + out_rate = out_rate / 2;
> + break;
> + case 0x02:
> + out_rate = out_rate / 4;
> + break;
> + case 0x03:
> + out_rate = out_rate / 8;
> + break;
> + default:
> + break;
> + }
out_rate >>= val;
Regards,
CK
> +
> + if (mtk_hdmi_phy_read(hdmi_phy, HDMI_CON2) & RG_HDMITX_EN_TX_POSDIV)
> + out_rate = out_rate / 5;
> +
> + hdmi_phy->pll_rate = out_rate;
> +
> + return hdmi_phy->pll_rate;
> +}
>
> static const struct clk_ops mtk_hdmi_phy_pll_ops = {
> .prepare = mtk_hdmi_pll_prepare,
> diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> index ed5916b..cb23c1e 100644
> --- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> +++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
> @@ -285,6 +285,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
> return 0;
> }
>
> +static unsigned long mtk_hdmi_pll_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
> +
> + return hdmi_phy->pll_rate;
> +}
> +
> static const struct clk_ops mtk_hdmi_phy_pll_ops = {
> .prepare = mtk_hdmi_pll_prepare,
> .unprepare = mtk_hdmi_pll_unprepare,
next prev parent reply other threads:[~2019-01-10 1:47 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1546585439-30455-1-git-send-email-chunhui.dai@mediatek.com>
[not found] ` <1546585439-30455-5-git-send-email-chunhui.dai@mediatek.com>
2019-01-09 16:54 ` [PATCH 4/9] drm/mediatek: fix the rate and divder of hdmi phy for MT2701 Matthias Brugger
2019-01-17 8:34 ` Chunhui Dai
[not found] ` <1546585439-30455-2-git-send-email-chunhui.dai@mediatek.com>
2019-01-09 16:55 ` [PATCH 1/9] drm/mediatek: recalculate hdmi phy clock of MT2701 by querying hardware Matthias Brugger
2019-01-10 1:47 ` CK Hu [this message]
[not found] ` <1546585439-30455-10-git-send-email-chunhui.dai@mediatek.com>
2019-01-09 16:58 ` [PATCH 9/9] drm/mediatek: add dpi dual edge support Matthias Brugger
2019-01-22 7:03 ` Jitao Shi
[not found] ` <6021c8950c3146bb941ed1355391106d@mtkmbs01n1.mediatek.inc>
2019-01-22 6:41 ` Jitao Shi
[not found] ` <1546585439-30455-3-git-send-email-chunhui.dai@mediatek.com>
2019-01-10 8:28 ` [PATCH 2/9] drm/mediatek: move the setting of fixed divider CK Hu
2019-01-17 8:49 ` Chunhui Dai
[not found] ` <1546585439-30455-4-git-send-email-chunhui.dai@mediatek.com>
2019-01-16 6:37 ` [PATCH 3/9] drm/mediatek: using different flags of clk for HDMI phy CK Hu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1547084829.27684.8.camel@mtksdaap41 \
--to=ck.hu@mediatek.com \
--cc=airlied@linux.ie \
--cc=bibby.hsieh@mediatek.com \
--cc=chunhui.dai@mediatek.com \
--cc=colin.king@canonical.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=jamesjj.liao@mediatek.com \
--cc=jitao.shi@mediatek.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=mturquette@baylibre.com \
--cc=p.zabel@pengutronix.de \
--cc=ryder.lee@mediatek.com \
--cc=sboyd@kernel.org \
--cc=sean.wang@mediatek.com \
--cc=srv_heupstream@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).