From: Madalin Bucur <madalin.bucur@nxp.com>
To: davem@davemloft.net, netdev@vger.kernel.org
Cc: roy.pledge@nxp.com, laurentiu.tudor@nxp.com,
linux-kernel@vger.kernel.org,
Madalin Bucur <madalin.bucur@nxp.com>
Subject: [PATCH 06/20] fsl/fman: remove unused struct member
Date: Tue, 8 Oct 2019 15:10:27 +0300 [thread overview]
Message-ID: <1570536641-25104-7-git-send-email-madalin.bucur@nxp.com> (raw)
In-Reply-To: <1570536641-25104-1-git-send-email-madalin.bucur@nxp.com>
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
---
drivers/net/ethernet/freescale/fman/fman_port.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/net/ethernet/freescale/fman/fman_port.c b/drivers/net/ethernet/freescale/fman/fman_port.c
index bd76c9730692..87b26f063cc8 100644
--- a/drivers/net/ethernet/freescale/fman/fman_port.c
+++ b/drivers/net/ethernet/freescale/fman/fman_port.c
@@ -435,7 +435,6 @@ struct fman_port_cfg {
struct fman_port_rx_pools_params {
u8 num_of_pools;
- u16 second_largest_buf_size;
u16 largest_buf_size;
};
@@ -946,8 +945,6 @@ static int set_ext_buffer_pools(struct fman_port *port)
port->rx_pools_params.num_of_pools = ext_buf_pools->num_of_pools_used;
port->rx_pools_params.largest_buf_size =
sizes_array[ordered_array[ext_buf_pools->num_of_pools_used - 1]];
- port->rx_pools_params.second_largest_buf_size =
- sizes_array[ordered_array[ext_buf_pools->num_of_pools_used - 2]];
/* FMBM_RMPD reg. - pool depletion */
if (buf_pool_depletion->pools_grp_mode_enable) {
--
2.1.0
next prev parent reply other threads:[~2019-10-08 12:11 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-08 12:10 [PATCH 00/20] DPAA fixes Madalin Bucur
2019-10-08 12:10 ` [PATCH 01/20] fsl/fman: don't touch liodn base regs reserved on non-PAMU SoCs Madalin Bucur
2019-10-08 12:10 ` [PATCH 02/20] dpaa_eth: defer probing after qbman Madalin Bucur
2019-10-08 12:10 ` [PATCH 03/20] dpaa_eth: remove redundant code Madalin Bucur
2019-10-08 12:10 ` [PATCH 04/20] fsl/fman: add API to get the device behind a fman port Madalin Bucur
2019-10-08 12:10 ` [PATCH 05/20] dpaa_eth: change DMA device Madalin Bucur
2019-10-08 12:10 ` Madalin Bucur [this message]
2019-10-08 12:10 ` [PATCH 07/20] dpaa_eth: use only one buffer pool per interface Madalin Bucur
2019-10-08 12:10 ` [PATCH 08/20] dpaa_eth: use page backed rx buffers Madalin Bucur
2019-10-08 12:10 ` [PATCH 09/20] dpaa_eth: perform DMA unmapping before read Madalin Bucur
2019-10-08 12:10 ` [PATCH 10/20] dpaa_eth: avoid timestamp read on error paths Madalin Bucur
2019-10-08 12:10 ` [PATCH 11/20] dpaa_eth: simplify variables used in dpaa_cleanup_tx_fd() Madalin Bucur
2019-10-08 12:10 ` [PATCH 12/20] dpaa_eth: use fd information " Madalin Bucur
2019-10-08 12:10 ` [PATCH 13/20] dpaa_eth: use a page to store the SGT Madalin Bucur
2019-10-08 12:10 ` [PATCH 14/20] soc: fsl: qbman: allow registering a device link for the portal user Madalin Bucur
2019-10-08 12:10 ` [PATCH 15/20] dpaa_eth: register a device link for the qman portal used Madalin Bucur
2019-10-08 12:10 ` [PATCH 16/20] dpaa_eth: add dropped frames to percpu ethtool stats Madalin Bucur
2019-10-08 12:10 ` [PATCH 17/20] dpaa_eth: remove netdev_err() for user errors Madalin Bucur
2019-10-08 12:10 ` [PATCH 18/20] dpaa_eth: extend delays in ndo_stop Madalin Bucur
2019-10-08 12:10 ` [PATCH 19/20] dpaa_eth: add dpaa_dma_to_virt() Madalin Bucur
2019-10-09 7:39 ` Christoph Hellwig
2019-10-09 10:06 ` Laurentiu Tudor
2019-10-09 10:56 ` Madalin-cristian Bucur
2019-10-08 12:10 ` [PATCH 20/20] dpaa_eth: cleanup skb_to_contig_fd() Madalin Bucur
2019-10-09 4:01 ` [PATCH 00/20] DPAA fixes Jakub Kicinski
2019-10-09 5:53 ` Madalin-cristian Bucur
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1570536641-25104-7-git-send-email-madalin.bucur@nxp.com \
--to=madalin.bucur@nxp.com \
--cc=davem@davemloft.net \
--cc=laurentiu.tudor@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=roy.pledge@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).