[PATCH v3 0/2] Add support to handle ZRX-DC Compliant PHYs

[PATCH v3 0/2] Add support to handle ZRX-DC Compliant PHYs

[Anvesh Salveru]

According the PCI Express base specification when PHY does not meet
ZRX-DC specification, after every 100ms timeout the link should
transition to recovery state when the link is in low power states. 

Ports that meet the ZRX-DC specification for 2.5 GT/s while in the
L1.Idle state and are therefore not required to implement the 100 ms
timeout and transition to Recovery should avoid implementing it, since
it will reduce the power savings expected from the L1 state.

DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.

We need to get the PHY property in controller driver. So, we are
proposing a new method phy_property_present() in the phy driver.

Platform specific phy drivers should implement the callback for
property_present which will return true if the property exists in
the PHY.

static bool xxxx_phy_property_present(struct phy *phy, const char *property)
{
       struct device *dev = &phy->dev;

       return of_property_read_bool(dev->of_node, property);
}

And controller platform driver should populate the phy_zrxdc_compliant
flag, which will be used by generic DesignWare driver.

pci->phy_zrxdc_compliant = phy_property_present(xxxx_ctrl->phy, "phy-zrxdc-compliant");

Anvesh Salveru (2):
  phy: core: add phy_property_present method
  PCI: dwc: add support to handle ZRX-DC Compliant PHYs

 drivers/pci/controller/dwc/pcie-designware.c |  6 ++++++
 drivers/pci/controller/dwc/pcie-designware.h |  4 ++++
 drivers/phy/phy-core.c                       | 26 ++++++++++++++++++++++++++
 include/linux/phy/phy.h                      |  8 ++++++++
 4 files changed, 44 insertions(+)

-- 
2.7.4

[PATCH v3 1/2] phy: core: add phy_property_present method

[Anvesh Salveru]

In some platforms, we need information of phy properties in
the controller drivers. This patch adds a new phy_property_present()
method which can be used to check if some property exists in PHY
or not.

In case of DesignWare PCIe controller, we need to write into controller
register to specify about ZRX-DC compliance property of the PHY, which
reduces the power consumption during lower power states.

Signed-off-by: Anvesh Salveru <anvesh.s@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
---
 drivers/phy/phy-core.c  | 26 ++++++++++++++++++++++++++
 include/linux/phy/phy.h |  8 ++++++++
 2 files changed, 34 insertions(+)

diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index b04f4fe..0a62eca 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -420,6 +420,32 @@ int phy_calibrate(struct phy *phy)
 EXPORT_SYMBOL_GPL(phy_calibrate);
 
 /**
+ * phy_property_present() - checks if the property is present in PHY
+ * @phy: the phy returned by phy_get()
+ * @property: name of the property to check
+ *
+ * Used to check if the given property is present in PHY. PHY drivers
+ * can implement this callback function to expose PHY properties to
+ * controller drivers.
+ *
+ * Returns: true if property exists, false otherwise
+ */
+bool phy_property_present(struct phy *phy, const char *property)
+{
+	bool ret;
+
+	if (!phy || !phy->ops->property_present)
+		return false;
+
+	mutex_lock(&phy->mutex);
+	ret = phy->ops->property_present(phy, property);
+	mutex_unlock(&phy->mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(phy_property_present);
+
+/**
  * phy_configure() - Changes the phy parameters
  * @phy: the phy returned by phy_get()
  * @opts: New configuration to apply
diff --git a/include/linux/phy/phy.h b/include/linux/phy/phy.h
index 15032f14..3dd8f3c 100644
--- a/include/linux/phy/phy.h
+++ b/include/linux/phy/phy.h
@@ -61,6 +61,7 @@ union phy_configure_opts {
  * @reset: resetting the phy
  * @calibrate: calibrate the phy
  * @release: ops to be performed while the consumer relinquishes the PHY
+ * @property_present: check if some property is present in PHY
  * @owner: the module owner containing the ops
  */
 struct phy_ops {
@@ -103,6 +104,7 @@ struct phy_ops {
 	int	(*reset)(struct phy *phy);
 	int	(*calibrate)(struct phy *phy);
 	void	(*release)(struct phy *phy);
+	bool	(*property_present)(struct phy *phy, const char *property);
 	struct module *owner;
 };
 
@@ -217,6 +219,7 @@ static inline enum phy_mode phy_get_mode(struct phy *phy)
 }
 int phy_reset(struct phy *phy);
 int phy_calibrate(struct phy *phy);
+bool phy_property_present(struct phy *phy, const char *property);
 static inline int phy_get_bus_width(struct phy *phy)
 {
 	return phy->attrs.bus_width;
@@ -354,6 +357,11 @@ static inline int phy_calibrate(struct phy *phy)
 	return -ENOSYS;
 }
 
+static inline bool phy_property_present(struct phy *phy, const char *property)
+{
+	return false;
+}
+
 static inline int phy_configure(struct phy *phy,
 				union phy_configure_opts *opts)
 {
-- 
2.7.4

[PATCH v3 2/2] PCI: dwc: add support to handle ZRX-DC Compliant PHYs

[Anvesh Salveru]

Many platforms use DesignWare controller but the PHY can be different in
different platforms. If the PHY is compliant is to ZRX-DC specification
it helps in low power consumption during power states.

If current data rate is 8.0 GT/s or higher and PHY is not compliant to
ZRX-DC specification, then after every 100ms link should transition to
recovery state during the low power states.

DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.

Platforms with ZRX-DC compliant PHY can set phy_zrxdc_compliant variable
to specify this property to the controller.

Signed-off-by: Anvesh Salveru <anvesh.s@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
---
Patchset v2 can be found at:
 - 1/2: https://lkml.org/lkml/2019/11/11/672
 - 2/2: https://lkml.org/lkml/2019/10/28/285

Changes w.r.t v2:
 - Addressed review comments
 - Rebased on latest linus/master

 drivers/pci/controller/dwc/pcie-designware.c | 6 ++++++
 drivers/pci/controller/dwc/pcie-designware.h | 4 ++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 820488d..36a01b7 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -556,4 +556,10 @@ void dw_pcie_setup(struct dw_pcie *pci)
 		       PCIE_PL_CHK_REG_CHK_REG_START;
 		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
 	}
+
+	if (pci->phy_zrxdc_compliant) {
+		val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
+		val &= ~PORT_LOGIC_GEN3_ZRXDC_NONCOMPL;
+		dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
+	}
 }
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 5a18e94..f43f986 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -60,6 +60,9 @@
 #define PCIE_MSI_INTR0_MASK		0x82C
 #define PCIE_MSI_INTR0_STATUS		0x830
 
+#define PCIE_PORT_GEN3_RELATED		0x890
+#define PORT_LOGIC_GEN3_ZRXDC_NONCOMPL	BIT(0)
+
 #define PCIE_ATU_VIEWPORT		0x900
 #define PCIE_ATU_REGION_INBOUND		BIT(31)
 #define PCIE_ATU_REGION_OUTBOUND	0
@@ -249,6 +252,7 @@ struct dw_pcie {
 	void __iomem		*atu_base;
 	u32			num_viewport;
 	u8			iatu_unroll_enabled;
+	bool			phy_zrxdc_compliant;
 	struct pcie_port	pp;
 	struct dw_pcie_ep	ep;
 	const struct dw_pcie_ops *ops;
-- 
2.7.4

RE: [PATCH v3 0/2] Add support to handle ZRX-DC Compliant PHYs

[Gustavo Pimentel]

Hi,

You missed to sending this patch series to linux-pci@vger.kernel.org.

Regards,
Gustavo

On Wed, Nov 20, 2019 at 13:26:9, Anvesh Salveru <anvesh.s@samsung.com> 
wrote:

> According the PCI Express base specification when PHY does not meet
> ZRX-DC specification, after every 100ms timeout the link should
> transition to recovery state when the link is in low power states. 
> 
> Ports that meet the ZRX-DC specification for 2.5 GT/s while in the
> L1.Idle state and are therefore not required to implement the 100 ms
> timeout and transition to Recovery should avoid implementing it, since
> it will reduce the power savings expected from the L1 state.
> 
> DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
> GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.
> 
> We need to get the PHY property in controller driver. So, we are
> proposing a new method phy_property_present() in the phy driver.
> 
> Platform specific phy drivers should implement the callback for
> property_present which will return true if the property exists in
> the PHY.
> 
> static bool xxxx_phy_property_present(struct phy *phy, const char *property)
> {
>        struct device *dev = &phy->dev;
> 
>        return of_property_read_bool(dev->of_node, property);
> }
> 
> And controller platform driver should populate the phy_zrxdc_compliant
> flag, which will be used by generic DesignWare driver.
> 
> pci->phy_zrxdc_compliant = phy_property_present(xxxx_ctrl->phy, "phy-zrxdc-compliant");
> 
> Anvesh Salveru (2):
>   phy: core: add phy_property_present method
>   PCI: dwc: add support to handle ZRX-DC Compliant PHYs
> 
>  drivers/pci/controller/dwc/pcie-designware.c |  6 ++++++
>  drivers/pci/controller/dwc/pcie-designware.h |  4 ++++
>  drivers/phy/phy-core.c                       | 26 ++++++++++++++++++++++++++
>  include/linux/phy/phy.h                      |  8 ++++++++
>  4 files changed, 44 insertions(+)
> 
> -- 
> 2.7.4