From: Ashish Kumar <Ashish.Kumar@nxp.com>
To: devicetree@vger.kernel.org, robh@kernel.org,
mark.rutland@arm.com, shawnguo@kernel.org
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Ashish Kumar <Ashish.Kumar@nxp.com>,
Xiaowei Bao <xiaowei.bao@nxp.com>
Subject: [Patch v2 1/5] arm64: dts: ls1028a: Add FlexSPI support
Date: Wed, 4 Dec 2019 16:28:14 +0530 [thread overview]
Message-ID: <1575457098-18368-2-git-send-email-Ashish.Kumar@nxp.com> (raw)
In-Reply-To: <1575457098-18368-1-git-send-email-Ashish.Kumar@nxp.com>
Add fspi node property for LS1028A SoC for FlexSPI driver.
Property added for FlexSPI controller and for the connected
slave device for the LS1028ARDB and LS1028AQDS target.
RDB and QDS are having one SPI-NOR flash device, mt35xu02g
connected at CS0.
This flash device "mt35xu02g" is tested for octal read
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
---
v2:
Rebased to top
Use "jedec,spi-nor" in compatibles
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 15 +++++++++++++++
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 15 +++++++++++++++
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 13 +++++++++++++
3 files changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
index 5b9d4b35dd35..ca409d907b36 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -123,6 +123,21 @@
status = "okay";
};
+&fspi {
+ status = "okay";
+
+ mt35xu02g0: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ /* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
+ spi-rx-bus-width = <8>; /* 8 SPI Rx lines */
+ spi-tx-bus-width = <1>; /* 1 SPI Tx line */
+ reg = <0>;
+ };
+};
+
&i2c0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
index 9720a190049f..af25c09ea427 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -96,6 +96,21 @@
status = "okay";
};
+&fspi {
+ status = "okay";
+
+ mt35xu02g0: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ /* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
+ spi-rx-bus-width = <8>; /* 8 SPI Rx lines */
+ spi-tx-bus-width = <1>; /* 1 SPI Tx line */
+ reg = <0>;
+ };
+};
+
&i2c0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 8e8a77eb596a..f7b79fce3df5 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -271,6 +271,19 @@
status = "disabled";
};
+ fspi: spi@20c0000 {
+ compatible = "nxp,lx2160a-fspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x20c0000 0x0 0x10000>,
+ <0x0 0x20000000 0x0 0x10000000>;
+ reg-names = "fspi_base", "fspi_mmap";
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 3>, <&clockgen 4 3>;
+ clock-names = "fspi_en", "fspi";
+ status = "disabled";
+ };
+
esdhc: mmc@2140000 {
compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
reg = <0x0 0x2140000 0x0 0x10000>;
--
2.17.1
next prev parent reply other threads:[~2019-12-04 10:58 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-04 10:58 [Patch v2 0/5] Add dts support for various NXP boards Ashish Kumar
2019-12-04 10:58 ` Ashish Kumar [this message]
2019-12-04 10:58 ` [Patch v2 2/5] arm64: dts: ls1046a: Add QSPI node for ls1046afrwy Ashish Kumar
2019-12-04 10:58 ` [Patch v2 3/5] arm64: dts: ls1046a: Update QSPI node properties of ls1046ardb Ashish Kumar
2019-12-04 10:58 ` [Patch v2 4/5] arm64: dts: ls208x: Remove non-compatible driver device from qspi node Ashish Kumar
2019-12-04 10:58 ` [Patch v2 5/5] arm64: dts: ls1088a: Add QSPI support for NXP LS1088 Ashish Kumar
2019-12-11 3:14 ` [Patch v2 0/5] Add dts support for various NXP boards Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1575457098-18368-2-git-send-email-Ashish.Kumar@nxp.com \
--to=ashish.kumar@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
--cc=xiaowei.bao@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).