From: Christophe Kerello <christophe.kerello@st.com>
To: <miquel.raynal@bootlin.com>, <richard@nod.at>, <vigneshr@ti.com>,
<robh+dt@kernel.org>, <mark.rutland@arm.com>,
<gregkh@linuxfoundation.org>, <boris.brezillon@collabora.com>
Cc: <linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<devicetree@vger.kernel.org>, <marex@denx.de>,
Christophe Kerello <christophe.kerello@st.com>
Subject: [PATCH v3 01/10] mtd: rawnand: stm32_fmc2: manage all errors cases at probe time
Date: Tue, 5 May 2020 19:10:59 +0200 [thread overview]
Message-ID: <1588698668-25288-2-git-send-email-christophe.kerello@st.com> (raw)
In-Reply-To: <1588698668-25288-1-git-send-email-christophe.kerello@st.com>
This patch defers its probe when the expected reset control is not
yet ready. This patch also handles properly all errors cases at probe
time.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
---
Changes in v3:
- rename labels used on errors
drivers/mtd/nand/raw/stm32_fmc2_nand.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/mtd/nand/raw/stm32_fmc2_nand.c b/drivers/mtd/nand/raw/stm32_fmc2_nand.c
index b6d45cd..50a6377 100644
--- a/drivers/mtd/nand/raw/stm32_fmc2_nand.c
+++ b/drivers/mtd/nand/raw/stm32_fmc2_nand.c
@@ -1967,7 +1967,11 @@ static int stm32_fmc2_probe(struct platform_device *pdev)
}
rstc = devm_reset_control_get(dev, NULL);
- if (!IS_ERR(rstc)) {
+ if (IS_ERR(rstc)) {
+ ret = PTR_ERR(rstc);
+ if (ret == -EPROBE_DEFER)
+ goto err_clk_disable;
+ } else {
reset_control_assert(rstc);
reset_control_deassert(rstc);
}
@@ -1975,7 +1979,7 @@ static int stm32_fmc2_probe(struct platform_device *pdev)
/* DMA setup */
ret = stm32_fmc2_dma_setup(fmc2);
if (ret)
- return ret;
+ goto err_release_dma;
/* FMC2 init routine */
stm32_fmc2_init(fmc2);
@@ -1997,20 +2001,20 @@ static int stm32_fmc2_probe(struct platform_device *pdev)
/* Scan to find existence of the device */
ret = nand_scan(chip, nand->ncs);
if (ret)
- goto err_scan;
+ goto err_release_dma;
ret = mtd_device_register(mtd, NULL, 0);
if (ret)
- goto err_device_register;
+ goto err_nand_cleanup;
platform_set_drvdata(pdev, fmc2);
return 0;
-err_device_register:
+err_nand_cleanup:
nand_cleanup(chip);
-err_scan:
+err_release_dma:
if (fmc2->dma_ecc_ch)
dma_release_channel(fmc2->dma_ecc_ch);
if (fmc2->dma_tx_ch)
@@ -2021,6 +2025,7 @@ static int stm32_fmc2_probe(struct platform_device *pdev)
sg_free_table(&fmc2->dma_data_sg);
sg_free_table(&fmc2->dma_ecc_sg);
+err_clk_disable:
clk_disable_unprepare(fmc2->clk);
return ret;
--
1.9.1
next prev parent reply other threads:[~2020-05-05 17:14 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-05 17:10 [PATCH v3 00/10] add STM32 FMC2 EBI controller driver Christophe Kerello
2020-05-05 17:10 ` Christophe Kerello [this message]
2020-05-05 17:11 ` [PATCH v3 02/10] mtd: rawnand: stm32_fmc2: remove useless inline comments Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 03/10] mtd: rawnand: stm32_fmc2: use FMC2_TIMEOUT_MS for timeouts Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 04/10] mtd: rawnand: stm32_fmc2: cleanup Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 05/10] mtd: rawnand: stm32_fmc2: use FIELD_PREP/FIELD_GET macros Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 06/10] dt-bindings: mtd: update STM32 FMC2 NAND controller documentation Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 07/10] dt-bindings: memory-controller: add STM32 FMC2 EBI " Christophe Kerello
2020-05-06 8:26 ` Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 08/10] memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 09/10] mtd: rawnand: stm32_fmc2: use regmap APIs Christophe Kerello
2020-05-05 17:11 ` [PATCH v3 10/10] mtd: rawnand: stm32_fmc2: get resources from parent node Christophe Kerello
2020-05-06 9:16 ` [PATCH v3 00/10] add STM32 FMC2 EBI controller driver Christophe Kerello
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1588698668-25288-2-git-send-email-christophe.kerello@st.com \
--to=christophe.kerello@st.com \
--cc=boris.brezillon@collabora.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=marex@denx.de \
--cc=mark.rutland@arm.com \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).