linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
To: ssantosh@kernel.org, s-anna@ti.com
Cc: grzegorz.jaszczyk@linaro.org, santosh.shilimkar@oracle.com,
	robh+dt@kernel.org, lee.jones@linaro.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	wmills@ti.com, praneeth@ti.com
Subject: [PATCH 6/6] soc: ti: pruss: enable support for ICSSG subsystems on K3 AM65x SoCs
Date: Wed, 29 Jul 2020 13:02:08 +0200	[thread overview]
Message-ID: <1596020528-19510-7-git-send-email-grzegorz.jaszczyk@linaro.org> (raw)
In-Reply-To: <1596020528-19510-1-git-send-email-grzegorz.jaszczyk@linaro.org>

From: Suman Anna <s-anna@ti.com>

The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem capable of supporting Gigabit Ethernet, and is
commonly referred to as ICSSG. These SoCs contain typically three
ICSSG instances named ICSSG0, ICSSG1 and ICSSG2. The three ICSSGs are
identical to each other for the most part with minor SoC integration
differences and capabilities. The ICSSG2 supports slightly enhanced
features like SGMII mode Ethernet, while the ICSS0 and ICSSG1 instances
are limited to MII mode only.

The ICSSGs on K3 AM65x SoCs are in general super-sets of the PRUSS on the
AM57xx/66AK2G SoCs. They include two additional auxiliary PRU cores called
RTUs and few other additional sub-modules. The interrupt integration is
also different on the K3 AM65x SoCs and are propagated through various
SoC-level Interrupt Router and Interrupt Aggregator blocks. Other IP level
differences include different constant tables, differences in system event
interrupt input sources etc. They also do not have a programmable module
reset line like those present on AM33xx/AM43xx SoCs. The modules are reset
just like any other IP with the SoC's global cold/warm resets.

The existing pruss platform driver has been updated to support these new
ICSSG instances through new AM65x specific compatibles. A build dependency
with ARCH_K3 is added to enable building all the existing PRUSS platform
drivers for this ARMv8 platform.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
---
 drivers/soc/ti/Kconfig | 2 +-
 drivers/soc/ti/pruss.c | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/soc/ti/Kconfig b/drivers/soc/ti/Kconfig
index c290343..f5b82ff 100644
--- a/drivers/soc/ti/Kconfig
+++ b/drivers/soc/ti/Kconfig
@@ -103,7 +103,7 @@ config TI_K3_SOCINFO
 
 config TI_PRUSS
 	tristate "TI PRU-ICSS Subsystem Platform drivers"
-	depends on SOC_AM33XX || SOC_AM43XX || SOC_DRA7XX || ARCH_KEYSTONE
+	depends on SOC_AM33XX || SOC_AM43XX || SOC_DRA7XX || ARCH_KEYSTONE || ARCH_K3
 	select MFD_SYSCON
 	help
 	  TI PRU-ICSS Subsystem platform specific support.
diff --git a/drivers/soc/ti/pruss.c b/drivers/soc/ti/pruss.c
index d5f128e..ccc9783 100644
--- a/drivers/soc/ti/pruss.c
+++ b/drivers/soc/ti/pruss.c
@@ -163,6 +163,7 @@ static const struct of_device_id pruss_of_match[] = {
 	{ .compatible = "ti,am4376-pruss1", .data = &am437x_pruss1_data, },
 	{ .compatible = "ti,am5728-pruss" },
 	{ .compatible = "ti,k2g-pruss" },
+	{ .compatible = "ti,am654-icssg" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, pruss_of_match);
-- 
2.7.4


  parent reply	other threads:[~2020-07-29 11:03 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-29 11:02 [PATCH 0/6] Add TI PRUSS platform driver Grzegorz Jaszczyk
2020-07-29 11:02 ` [PATCH 1/6] dt-bindings: soc: ti: Add TI PRUSS bindings Grzegorz Jaszczyk
2020-08-17 21:14   ` Rob Herring
2020-08-18 22:07     ` Grzegorz Jaszczyk
2020-07-29 11:02 ` [PATCH 2/6] soc: ti: pruss: Add a platform driver for PRUSS in TI SoCs Grzegorz Jaszczyk
2020-07-29 11:02 ` [PATCH 3/6] soc: ti: pruss: Add support for PRU-ICSSs on AM437x SoCs Grzegorz Jaszczyk
2020-07-29 11:02 ` [PATCH 4/6] soc: ti: pruss: Add support for PRU-ICSS subsystems on AM57xx SoCs Grzegorz Jaszczyk
2020-07-29 11:02 ` [PATCH 5/6] soc: ti: pruss: Add support for PRU-ICSS subsystems on 66AK2G SoC Grzegorz Jaszczyk
2020-07-29 11:02 ` Grzegorz Jaszczyk [this message]
2020-08-02 11:53 ` [PATCH 0/6] Add TI PRUSS platform driver Pavel Machek
2020-08-02 11:57   ` Pavel Machek
2020-08-02 21:41     ` Grzegorz Jaszczyk
2020-08-20 14:43 ` Suman Anna
2020-08-20 16:27   ` santosh.shilimkar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1596020528-19510-7-git-send-email-grzegorz.jaszczyk@linaro.org \
    --to=grzegorz.jaszczyk@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=praneeth@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=s-anna@ti.com \
    --cc=santosh.shilimkar@oracle.com \
    --cc=ssantosh@kernel.org \
    --cc=wmills@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).