From: meenakshi.aggarwal@nxp.com
To: shawnguo@kernel.org, robh+dt@kernel.org, V.sethi@nxp.com,
leoyang.li@nxp.com, linux-arm-kernel@lists.infradead.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>,
Ioana Ciornei <ioana.ciornei@nxp.com>,
Kuldeep Singh <kuldeep.singh@nxp.com>
Subject: [PATCH 2/2] arm64: dts: lx2160a: add device tree for lx2162aqds board
Date: Wed, 2 Sep 2020 20:43:30 +0530 [thread overview]
Message-ID: <1599059610-7570-2-git-send-email-meenakshi.aggarwal@nxp.com> (raw)
In-Reply-To: <1599059610-7570-1-git-send-email-meenakshi.aggarwal@nxp.com>
From: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts | 336 ++++++++++++++++++++++
2 files changed, 337 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a39f0a1..ab9fbd3 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
new file mode 100644
index 0000000..a81c6a4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
@@ -0,0 +1,336 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2162AQDS
+//
+// Copyright 2020 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2162AQDS";
+ compatible = "nxp,lx2162a-qds", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-sb3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MC34717-3.3VSB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ mdio-mux-1 {
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 0>;
+ mdio-parent-bus = <&emdio1>;
+ #address-cells=<1>;
+ #size-cells = <0>;
+
+ mdio@0 { /* On-board RTL8211F PHY #1 RGMII1*/
+ reg = <0x00>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ eee-broken-1000t;
+ };
+ };
+
+ mdio@8 { /* On-board RTL8211F PHY #2 RGMII2*/
+ reg = <0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rgmii_phy2: ethernet-phy@2 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x2>;
+ eee-broken-1000t;
+ };
+ };
+
+ mdio@18 { /* Slot #1 */
+ reg = <0x18>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@19 { /* Slot #2 */
+ reg = <0x19>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1a { /* Slot #3 */
+ reg = <0x1a>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1b { /* Slot #4 */
+ reg = <0x1b>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1c { /* Slot #5 */
+ reg = <0x1c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1d { /* Slot #6 */
+ reg = <0x1d>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1e { /* Slot #7 */
+ reg = <0x1e>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1f { /* Slot #8 */
+ reg = <0x1f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ mdio-mux-2 {
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 1>;
+ mdio-parent-bus = <&emdio2>;
+ #address-cells=<1>;
+ #size-cells = <0>;
+
+ mdio@0 { /* Slot #1 (secondary EMI) */
+ reg = <0x00>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1 { /* Slot #2 (secondary EMI) */
+ reg = <0x01>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@2 { /* Slot #3 (secondary EMI) */
+ reg = <0x02>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@3 { /* Slot #4 (secondary EMI) */
+ reg = <0x03>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@4 { /* Slot #5 (secondary EMI) */
+ reg = <0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@5 { /* Slot #6 (secondary EMI) */
+ reg = <0x05>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@6 { /* Slot #7 (secondary EMI) */
+ reg = <0x06>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@7 { /* Slot #8 (secondary EMI) */
+ reg = <0x07>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&dpmac17 {
+ phy-handle = <&rgmii_phy1>;
+ phy-connection-type = "rgmii-id";
+};
+
+&dpmac18 {
+ phy-handle = <&rgmii_phy2>;
+ phy-connection-type = "rgmii-id";
+};
+
+&dspi0 {
+ status = "okay";
+
+ dflash0: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&dspi1 {
+ status = "okay";
+
+ dflash1: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&dspi2 {
+ status = "okay";
+
+ dflash2: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&emdio1 {
+ status = "okay";
+};
+
+&emdio2 {
+ status = "okay";
+};
+
+&esdhc0 {
+ status = "okay";
+};
+
+&esdhc1 {
+ status = "okay";
+};
+
+&fspi {
+ status = "okay";
+
+ mt35xu512aba0: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <8>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ fpga@66 {
+ compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
+ "simple-mfd";
+ reg = <0x66>;
+
+ mux: mux-controller {
+ compatible = "reg-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
+ <0x54 0x07>; /* 1: reg 0x54, bit 2:0 */
+ };
+ };
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&sata3 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
--
2.7.4
next prev parent reply other threads:[~2020-09-02 15:14 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-02 15:13 [PATCH 1/2] dt-bindings: arm64: add compatible for LX2162A QDS Board meenakshi.aggarwal
2020-09-02 15:13 ` meenakshi.aggarwal [this message]
2020-09-05 7:54 ` [PATCH 2/2] arm64: dts: lx2160a: add device tree for lx2162aqds board Shawn Guo
2020-09-09 7:10 ` Meenakshi Aggarwal
2020-09-12 9:49 ` Shawn Guo
2020-09-21 6:00 ` Meenakshi Aggarwal
2020-09-21 13:03 ` Shawn Guo
2020-09-21 13:34 ` Meenakshi Aggarwal
2020-09-29 10:01 ` [PATCH v3 0/2] Add device tree support for LX2162AQDS board meenakshi.aggarwal
2020-09-29 10:01 ` [PATCH v3 1/2] dt-bindings: arm64: add compatible for LX2162A QDS Board meenakshi.aggarwal
2020-09-29 10:01 ` [PATCH v3 2/2] arm64: dts: lx2160a: add device tree for lx2162aqds board meenakshi.aggarwal
2020-10-19 9:00 ` Meenakshi Aggarwal
2020-10-26 7:18 ` Shawn Guo
2020-10-26 14:35 ` Leo Li
2020-10-30 8:59 ` Meenakshi Aggarwal
2020-11-02 5:59 ` [PATCH v4 0/2] Add device tree support for LX2162AQDS board meenakshi.aggarwal
2020-11-02 5:59 ` [PATCH v4 1/2] dt-bindings: arm64: add compatible for LX2162A QDS Board meenakshi.aggarwal
2020-11-02 5:59 ` [PATCH v4 2/2] arm64: dts: lx2160a: add device tree for lx2162aqds board meenakshi.aggarwal
2020-11-02 23:25 ` [PATCH v4 0/2] Add device tree support for LX2162AQDS board Shawn Guo
2020-09-14 20:23 ` [PATCH 1/2] dt-bindings: arm64: add compatible for LX2162A QDS Board Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1599059610-7570-2-git-send-email-meenakshi.aggarwal@nxp.com \
--to=meenakshi.aggarwal@nxp.com \
--cc=V.sethi@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=ioana.ciornei@nxp.com \
--cc=kuldeep.singh@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).