From: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
To: sboyd@kernel.org, agross@kernel.org, bjorn.andersson@linaro.org,
david.brown@linaro.org, devicetree@vger.kernel.org,
jassisinghbrar@gmail.com, linux-arm-msm@vger.kernel.org,
linux-clk@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-remoteproc@vger.kernel.org, mark.rutland@arm.com,
mturquette@baylibre.com, ohad@wizery.com, robh+dt@kernel.org,
sricharan@codeaurora.org, gokulsri@codeaurora.org
Subject: [PATCH v8 9/9] arm64: dts: qcom: Enable Q6v5 WCSS for ipq8074 SoC
Date: Sat, 30 Jan 2021 10:50:13 +0530 [thread overview]
Message-ID: <1611984013-10201-10-git-send-email-gokulsri@codeaurora.org> (raw)
In-Reply-To: <1611984013-10201-1-git-send-email-gokulsri@codeaurora.org>
Enable remoteproc WCSS PIL driver with glink
and ssr subdevices. Also configures shared memory
and enables smp2p and mailboxes required for IPC.
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Nikhil Prakash V <nprakash@codeaurora.org>
---
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 121 ++++++++++++++++++++++++++++++++++
1 file changed, 121 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 6e719b4..9bde3f9c 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -76,12 +76,66 @@
method = "smc";
};
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ smem_region: memory@4ab00000 {
+ no-map;
+ reg = <0x0 0x4ab00000 0x0 0x00100000>;
+ };
+
+ q6_region: memory@4b000000 {
+ no-map;
+ reg = <0x0 0x4b000000 0x0 0x05f00000>;
+ };
+ };
+
firmware {
scm {
compatible = "qcom,scm-ipq8074", "qcom,scm";
};
};
+ tcsr_mutex: hwlock@193d000 {
+ compatible = "qcom,tcsr-mutex";
+ syscon = <&tcsr_mutex_regs 0 0x80>;
+ #hwlock-cells = <1>;
+ };
+
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_region>;
+ hwlocks = <&tcsr_mutex 0>;
+ };
+
+ wcss: smp2p-wcss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <0 322 1>;
+
+ mboxes = <&apcs_glb 9>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ wcss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ qcom,smp2p-feature-ssr-ack;
+ #qcom,smem-state-cells = <1>;
+ };
+
+ wcss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
soc: soc {
#address-cells = <0x1>;
#size-cells = <0x1>;
@@ -695,5 +749,72 @@
"axi_m_sticky";
status = "disabled";
};
+
+ tcsr_q6: syscon@1945000 {
+ compatible = "syscon";
+ reg = <0x01945000 0xe000>;
+ };
+
+ tcsr_mutex_regs: syscon@193d000 {
+ compatible = "syscon";
+ reg = <0x01905000 0x8000>;
+ };
+
+ apcs_glb: mailbox@b111000 {
+ compatible = "qcom,ipq8074-apcs-apps-global";
+ reg = <0x0b111000 0x1000>;
+
+ #mbox-cells = <1>;
+ };
+
+ q6v5_wcss: q6v5_wcss@cd00000 {
+ compatible = "qcom,ipq8074-wcss-pil";
+ reg = <0x0cd00000 0x4040>,
+ <0x004ab000 0x20>;
+ reg-names = "qdsp6",
+ "rmb";
+ qca,auto-restart;
+ qca,extended-intc;
+ interrupts-extended = <&intc 0 325 1>,
+ <&wcss_smp2p_in 0 0>,
+ <&wcss_smp2p_in 1 0>,
+ <&wcss_smp2p_in 2 0>,
+ <&wcss_smp2p_in 3 0>;
+ interrupt-names = "wdog",
+ "fatal",
+ "ready",
+ "handover",
+ "stop-ack";
+
+ resets = <&gcc GCC_WCSSAON_RESET>,
+ <&gcc GCC_WCSS_BCR>,
+ <&gcc GCC_WCSS_Q6_BCR>;
+
+ reset-names = "wcss_aon_reset",
+ "wcss_reset",
+ "wcss_q6_reset";
+
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "prng";
+
+ qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>;
+
+ qcom,smem-states = <&wcss_smp2p_out 0>,
+ <&wcss_smp2p_out 1>;
+ qcom,smem-state-names = "shutdown",
+ "stop";
+
+ memory-region = <&q6_region>;
+
+ glink-edge {
+ interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
+ qcom,remote-pid = <1>;
+ mboxes = <&apcs_glb 8>;
+
+ rpm_requests {
+ qcom,glink-channels = "IPCRTR";
+ };
+ };
+ };
};
};
--
2.7.4
prev parent reply other threads:[~2021-01-30 8:58 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-30 5:20 [PATCH v8 0/9] remoteproc: qcom: q6v5-wcss: Add support for secure pil Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 1/9] remoteproc: qcom: Add PRNG proxy clock Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 2/9] remoteproc: qcom: Add secure PIL support Gokul Sriram Palanisamy
2021-03-18 2:05 ` Bjorn Andersson
2021-01-30 5:20 ` [PATCH v8 3/9] remoteproc: qcom: Add support for split q6 + m3 wlan firmware Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 4/9] remoteproc: qcom: Add ssr subdevice identifier Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 5/9] remoteproc: qcom: Update regmap offsets for halt register Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 6/9] dt-bindings: clock: qcom: Add reset for WCSSAON Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 7/9] clk: qcom: Add WCSSAON reset Gokul Sriram Palanisamy
2021-01-30 5:20 ` [PATCH v8 8/9] arm64: dts: Add support for scm on IPQ8074 SoCs Gokul Sriram Palanisamy
2021-01-30 5:20 ` Gokul Sriram Palanisamy [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1611984013-10201-10-git-send-email-gokulsri@codeaurora.org \
--to=gokulsri@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jassisinghbrar@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=ohad@wizery.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sricharan@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).