[PATCH v12 net-next 00/15] net: mvpp2: Add TX Flow Control support

[PATCH v12 net-next 00/15] net: mvpp2: Add TX Flow Control support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Armada hardware has a pause generation mechanism in GOP (MAC).
The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.

Problem is that Packet Processor that actually can drop packets due to lack of resources not connected to the GOP flow control generation mechanism.
To solve this issue Armada has firmware running on CM3 CPU dedicated for Flow Control support.
Firmware monitors Packet Processor resources and asserts XON/XOFF by writing to Ports Control 0 Register.

MSS shared SRAM memory used to communicate between CM3 firmware and PP2 driver.
During init PP2 driver informs firmware about used BM pools, RXQs, congestion and depletion thresholds.

The pause frames are generated whenever congestion or depletion in resources is detected.
The back pressure is stopped when the resource reaches a sufficient level.
So the congestion/depletion and sufficient level implement a hysteresis that reduces the XON/XOFF toggle frequency.

Packet Processor v23 hardware introduces support for RX FIFO fill level monitor.
Patch "add PPv23 version definition" to differ between v23 and v22 hardware.
Patch "add TX FC firmware check" verifies that CM3 firmware supports Flow Control monitoring.

v11 --> v12
- Improve warning message in "net: mvpp2: add TX FC firmware check" patch

v10 --> v11
- Improve "net: mvpp2: add CM3 SRAM memory map" comment
- Move condition check to 'net: mvpp2: always compare hw-version vs MVPP21' patch

v9 --> v10
- Add CM3 SRAM description to PPv2 documentation

v8 --> v9
- Replace generic pool allocation with devm_ioremap_resource

v7 --> v8
- Reorder "always compare hw-version vs MVPP21" and "add PPv23 version definition" commits
- Typo fixes
- Remove condition fix from "add RXQ flow control configurations"

v6 --> v7
- Reduce patch set from 18 to 15 patches
 - Documentation change combined into a single patch
 - RXQ and BM size change combined into a single patch
 - Ring size change check moved into "add RXQ flow control configurations" commit

v5 --> v6
- No change

v4 --> v5
- Add missed Signed-off
- Fix warnings in patches 3 and 12
- Add revision requirement to warning message
- Move mss_spinlock into RXQ flow control configurations patch
- Improve FCA RXQ non occupied descriptor threshold commit message

v3 --> v4
- Remove RFC tag

v2 --> v3
- Remove inline functions
- Add PPv2.3 description into marvell-pp2.txt
- Improve mvpp2_interrupts_mask/unmask procedure
- Improve FC enable/disable procedure
- Add priv->sram_pool check
- Remove gen_pool_destroy call
- Reduce Flow Control timer to x100 faster

v1 --> v2
- Add memory requirements information
- Add EPROBE_DEFER if of_gen_pool_get return NULL
- Move Flow control configuration to mvpp2_mac_link_up callback
- Add firmware version info with Flow control support

Konstantin Porotchkin (1):
  dts: marvell: add CM3 SRAM memory to cp11x ethernet device tree

Stefan Chulski (14):
  doc: marvell: add CM3 address space and PPv2.3 description
  net: mvpp2: add CM3 SRAM memory map
  net: mvpp2: always compare hw-version vs MVPP21
  net: mvpp2: add PPv23 version definition
  net: mvpp2: increase BM pool and RXQ size
  net: mvpp2: add FCA periodic timer configurations
  net: mvpp2: add FCA RXQ non occupied descriptor threshold
  net: mvpp2: enable global flow control
  net: mvpp2: add RXQ flow control configurations
  net: mvpp2: add ethtool flow control configuration support
  net: mvpp2: add BM protection underrun feature support
  net: mvpp2: add PPv23 RX FIFO flow control
  net: mvpp2: set 802.3x GoP Flow Control mode
  net: mvpp2: add TX FC firmware check

 Documentation/devicetree/bindings/net/marvell-pp2.txt |   6 +-
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi         |   2 +-
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h            | 124 ++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c       | 523 ++++++++++++++++++--
 4 files changed, 606 insertions(+), 49 deletions(-)

-- 
1.9.1

[PATCH v12 net-next 01/15] doc: marvell: add CM3 address space and PPv2.3 description

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Patch adds CM3 address space and PPv2.3 description.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 Documentation/devicetree/bindings/net/marvell-pp2.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index b783976..ce15c17 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -1,5 +1,6 @@
 * Marvell Armada 375 Ethernet Controller (PPv2.1)
   Marvell Armada 7K/8K Ethernet Controller (PPv2.2)
+  Marvell CN913X Ethernet Controller (PPv2.3)
 
 Required properties:
 
@@ -12,10 +13,11 @@ Required properties:
 	- common controller registers
 	- LMS registers
 	- one register area per Ethernet port
-  For "marvell,armada-7k-pp2", must contain the following register
+  For "marvell,armada-7k-pp2" used by 7K/8K and CN913X, must contain the following register
   sets:
 	- packet processor registers
 	- networking interfaces registers
+	- CM3 address space used for TX Flow Control
 
 - clocks: pointers to the reference clocks for this device, consequently:
 	- main controller clock (for both armada-375-pp2 and armada-7k-pp2)
@@ -81,7 +83,7 @@ Example for marvell,armada-7k-pp2:
 
 cpm_ethernet: ethernet@0 {
 	compatible = "marvell,armada-7k-pp22";
-	reg = <0x0 0x100000>, <0x129000 0xb000>;
+	reg = <0x0 0x100000>, <0x129000 0xb000>, <0x220000 0x800>;
 	clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>,
 		 <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>;
 	clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk";
-- 
1.9.1

[PATCH v12 net-next 02/15] dts: marvell: add CM3 SRAM memory to cp11x ethernet device tree

[stefanc]

From: Konstantin Porotchkin <kostap@marvell.com>

CM3 SRAM address space will be used for Flow Control configuration.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 9dcf16b..6fe0d26 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -59,7 +59,7 @@
 
 		CP11X_LABEL(ethernet): ethernet@0 {
 			compatible = "marvell,armada-7k-pp22";
-			reg = <0x0 0x100000>, <0x129000 0xb000>;
+			reg = <0x0 0x100000>, <0x129000 0xb000>, <0x220000 0x800>;
 			clocks = <&CP11X_LABEL(clk) 1 3>, <&CP11X_LABEL(clk) 1 9>,
 				 <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>,
 				 <&CP11X_LABEL(clk) 1 18>;
-- 
1.9.1

[PATCH v12 net-next 03/15] net: mvpp2: add CM3 SRAM memory map

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch adds CM3 memory map.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  1 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 26 ++++++++++++++++++++
 2 files changed, 27 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 6bd7e40..56e90ab 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -925,6 +925,7 @@ struct mvpp2 {
 	/* Shared registers' base addresses */
 	void __iomem *lms_base;
 	void __iomem *iface_base;
+	void __iomem *cm3_base;
 
 	/* On PPv2.2, each "software thread" can access the base
 	 * register through a separate address space, each 64 KB apart
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a07cf60..eec3796 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6846,6 +6846,27 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	return 0;
 }
 
+static int mvpp2_get_sram(struct platform_device *pdev,
+			  struct mvpp2 *priv)
+{
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	if (!res) {
+		if (has_acpi_companion(&pdev->dev))
+			dev_warn(&pdev->dev, "ACPI is too old, Flow control not supported\n");
+		else
+			dev_warn(&pdev->dev, "DT is too old, Flow control not supported\n");
+		return 0;
+	}
+
+	priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->cm3_base))
+		return PTR_ERR(priv->cm3_base);
+
+	return 0;
+}
+
 static int mvpp2_probe(struct platform_device *pdev)
 {
 	const struct acpi_device_id *acpi_id;
@@ -6902,6 +6923,11 @@ static int mvpp2_probe(struct platform_device *pdev)
 		priv->iface_base = devm_ioremap_resource(&pdev->dev, res);
 		if (IS_ERR(priv->iface_base))
 			return PTR_ERR(priv->iface_base);
+
+		/* Map CM3 SRAM */
+		err = mvpp2_get_sram(pdev, priv);
+		if (err)
+			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
 	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
-- 
1.9.1

[PATCH v12 net-next 04/15] net: mvpp2: always compare hw-version vs MVPP21

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 38 ++++++++++----------
 1 file changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index eec3796..17cd161 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -319,7 +319,7 @@ static int mvpp2_get_nrxqs(struct mvpp2 *priv)
 {
 	unsigned int nrxqs;
 
-	if (priv->hw_version == MVPP22 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
+	if (priv->hw_version != MVPP21 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
 		return 1;
 
 	/* According to the PPv2.2 datasheet and our experiments on
@@ -446,7 +446,7 @@ static void mvpp2_bm_bufs_get_addrs(struct device *dev, struct mvpp2 *priv,
 				      MVPP2_BM_PHY_ALLOC_REG(bm_pool->id));
 	*phys_addr = mvpp2_thread_read(priv, thread, MVPP2_BM_VIRT_ALLOC_REG);
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		u32 val;
 		u32 dma_addr_highbits, phys_addr_highbits;
 
@@ -742,7 +742,7 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 	if (test_bit(thread, &port->priv->lock_map))
 		spin_lock_irqsave(&port->bm_lock[thread], flags);
 
-	if (port->priv->hw_version == MVPP22) {
+	if (port->priv->hw_version != MVPP21) {
 		u32 val = 0;
 
 		if (sizeof(dma_addr_t) == 8)
@@ -1172,7 +1172,7 @@ static void mvpp2_interrupts_unmask(void *arg)
 	u32 val;
 	int i;
 
-	if (port->priv->hw_version != MVPP22)
+	if (port->priv->hw_version == MVPP21)
 		return;
 
 	if (mask)
@@ -1199,7 +1199,7 @@ static bool mvpp2_port_supports_xlg(struct mvpp2_port *port)
 
 static bool mvpp2_port_supports_rgmii(struct mvpp2_port *port)
 {
-	return !(port->priv->hw_version == MVPP22 && port->gop_id == 0);
+	return !(port->priv->hw_version != MVPP21 && port->gop_id == 0);
 }
 
 /* Port configuration routines */
@@ -1817,7 +1817,7 @@ static void mvpp2_mac_reset_assert(struct mvpp2_port *port)
 	      MVPP2_GMAC_PORT_RESET_MASK;
 	writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
 
-	if (port->priv->hw_version == MVPP22 && port->gop_id == 0) {
+	if (port->priv->hw_version != MVPP21 && port->gop_id == 0) {
 		val = readl(port->base + MVPP22_XLG_CTRL0_REG) &
 		      ~MVPP22_XLG_CTRL0_MAC_RESET_DIS;
 		writel(val, port->base + MVPP22_XLG_CTRL0_REG);
@@ -1830,7 +1830,7 @@ static void mvpp22_pcs_reset_assert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -1851,7 +1851,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -4188,7 +4188,7 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
 	/* Enable interrupts on all threads */
 	mvpp2_interrupts_enable(port);
 
-	if (port->priv->hw_version == MVPP22)
+	if (port->priv->hw_version != MVPP21)
 		mvpp22_mode_reconfigure(port);
 
 	if (port->phylink) {
@@ -4404,7 +4404,7 @@ static int mvpp2_open(struct net_device *dev)
 		valid = true;
 	}
 
-	if (priv->hw_version == MVPP22 && port->port_irq) {
+	if (priv->hw_version != MVPP21 && port->port_irq) {
 		err = request_irq(port->port_irq, mvpp2_port_isr, 0,
 				  dev->name, port);
 		if (err) {
@@ -6052,7 +6052,7 @@ static int mvpp2__mac_prepare(struct phylink_config *config, unsigned int mode,
 			     MVPP2_GMAC_PORT_RESET_MASK,
 			     MVPP2_GMAC_PORT_RESET_MASK);
 
-		if (port->priv->hw_version == MVPP22) {
+		if (port->priv->hw_version != MVPP21) {
 			mvpp22_gop_mask_irq(port);
 
 			phy_power_off(port->comphy);
@@ -6106,7 +6106,7 @@ static int mvpp2_mac_finish(struct phylink_config *config, unsigned int mode,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 
-	if (port->priv->hw_version == MVPP22 &&
+	if (port->priv->hw_version != MVPP21 &&
 	    port->phy_interface != interface) {
 		port->phy_interface = interface;
 
@@ -6786,7 +6786,7 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	if (dram_target_info)
 		mvpp2_conf_mbus_windows(dram_target_info, priv);
 
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		mvpp2_axi_init(priv);
 
 	/* Disable HW PHY polling */
@@ -6930,7 +6930,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
-	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
+	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
 		priv->sysctrl_base =
 			syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
 							"marvell,system-controller");
@@ -6943,7 +6943,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->sysctrl_base = NULL;
 	}
 
-	if (priv->hw_version == MVPP22 &&
+	if (priv->hw_version != MVPP21 &&
 	    mvpp2_get_nrxqs(priv) * 2 <= MVPP2_BM_MAX_POOLS)
 		priv->percpu_pools = 1;
 
@@ -6988,7 +6988,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		if (err < 0)
 			goto err_pp_clk;
 
-		if (priv->hw_version == MVPP22) {
+		if (priv->hw_version != MVPP21) {
 			priv->mg_clk = devm_clk_get(&pdev->dev, "mg_clk");
 			if (IS_ERR(priv->mg_clk)) {
 				err = PTR_ERR(priv->mg_clk);
@@ -7029,7 +7029,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		err = dma_set_mask(&pdev->dev, MVPP2_DESC_DMA_MASK);
 		if (err)
 			goto err_axi_clk;
@@ -7104,10 +7104,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 	clk_disable_unprepare(priv->axi_clk);
 
 err_mg_core_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_core_clk);
 err_mg_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_clk);
 err_gop_clk:
 	clk_disable_unprepare(priv->gop_clk);
-- 
1.9.1

[PATCH v12 net-next 05/15] net: mvpp2: add PPv23 version definition

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 24 ++++++++++++--------
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 15 ++++++++----
 2 files changed, 24 insertions(+), 15 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 56e90ab..ce08086 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -60,6 +60,9 @@
 /* Top Registers */
 #define MVPP2_MH_REG(port)			(0x5040 + 4 * (port))
 #define MVPP2_DSA_EXTENDED			BIT(5)
+#define MVPP2_VER_ID_REG			0x50b0
+#define MVPP2_VER_PP22				0x10
+#define MVPP2_VER_PP23				0x11
 
 /* Parser Registers */
 #define MVPP2_PRS_INIT_LOOKUP_REG		0x1000
@@ -469,7 +472,7 @@
 #define     MVPP22_GMAC_INT_SUM_MASK_LINK_STAT	BIT(1)
 #define	    MVPP22_GMAC_INT_SUM_MASK_PTP	BIT(2)
 
-/* Per-port XGMAC registers. PPv2.2 only, only for GOP port 0,
+/* Per-port XGMAC registers. PPv2.2 and PPv2.3, only for GOP port 0,
  * relative to port->base.
  */
 #define MVPP22_XLG_CTRL0_REG			0x100
@@ -506,7 +509,7 @@
 #define     MVPP22_XLG_CTRL4_MACMODSELECT_GMAC	BIT(12)
 #define     MVPP22_XLG_CTRL4_EN_IDLE_CHECK	BIT(14)
 
-/* SMI registers. PPv2.2 only, relative to priv->iface_base. */
+/* SMI registers. PPv2.2 and PPv2.3, relative to priv->iface_base. */
 #define MVPP22_SMI_MISC_CFG_REG			0x1204
 #define     MVPP22_SMI_POLLING_EN		BIT(10)
 
@@ -582,7 +585,7 @@
 #define MVPP2_QUEUE_NEXT_DESC(q, index) \
 	(((index) < (q)->last_desc) ? ((index) + 1) : 0)
 
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers.PPv2.2 and PPv2.3 */
 #define MVPP22_MPCS_BASE(port)			(0x7000 + (port) * 0x1000)
 #define MVPP22_MPCS_CTRL			0x14
 #define     MVPP22_MPCS_CTRL_FWD_ERR_CONN	BIT(10)
@@ -593,7 +596,7 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
 #define     MVPP22_XPCS_CFG0_RESET_DIS		BIT(0)
@@ -927,15 +930,16 @@ struct mvpp2 {
 	void __iomem *iface_base;
 	void __iomem *cm3_base;
 
-	/* On PPv2.2, each "software thread" can access the base
+	/* On PPv2.2 and PPv2.3, each "software thread" can access the base
 	 * register through a separate address space, each 64 KB apart
 	 * from each other. Typically, such address spaces will be
 	 * used per CPU.
 	 */
 	void __iomem *swth_base[MVPP2_MAX_THREADS];
 
-	/* On PPv2.2, some port control registers are located into the system
-	 * controller space. These registers are accessible through a regmap.
+	/* On PPv2.2 and PPv2.3, some port control registers are located into
+	 * the system controller space. These registers are accessible
+	 * through a regmap.
 	 */
 	struct regmap *sysctrl_base;
 
@@ -977,7 +981,7 @@ struct mvpp2 {
 	u32 tclk;
 
 	/* HW version */
-	enum { MVPP21, MVPP22 } hw_version;
+	enum { MVPP21, MVPP22, MVPP23 } hw_version;
 
 	/* Maximum number of RXQs per port */
 	unsigned int max_port_rxqs;
@@ -1221,7 +1225,7 @@ struct mvpp21_rx_desc {
 	__le32 reserved8;
 };
 
-/* HW TX descriptor for PPv2.2 */
+/* HW TX descriptor for PPv2.2 and PPv2.3 */
 struct mvpp22_tx_desc {
 	__le32 command;
 	u8  packet_offset;
@@ -1233,7 +1237,7 @@ struct mvpp22_tx_desc {
 	__le64 buf_cookie_misc;
 };
 
-/* HW RX descriptor for PPv2.2 */
+/* HW RX descriptor for PPv2.2 and PPv2.3 */
 struct mvpp22_rx_desc {
 	__le32 status;
 	__le16 reserved1;
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 17cd161..5730900 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -384,7 +384,7 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 	if (!IS_ALIGNED(size, 16))
 		return -EINVAL;
 
-	/* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 needs 16
+	/* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 and PPv2.3 needs 16
 	 * bytes per buffer pointer
 	 */
 	if (priv->hw_version == MVPP21)
@@ -5456,7 +5456,7 @@ static void mvpp2_rx_irqs_setup(struct mvpp2_port *port)
 		return;
 	}
 
-	/* Handle the more complicated PPv2.2 case */
+	/* Handle the more complicated PPv2.2 and PPv2.3 case */
 	for (i = 0; i < port->nqvecs; i++) {
 		struct mvpp2_queue_vector *qv = port->qvecs + i;
 
@@ -5633,7 +5633,7 @@ static bool mvpp22_port_has_legacy_tx_irqs(struct device_node *port_node,
 
 /* Checks if the port dt description has the required Tx interrupts:
  * - PPv2.1: there are no such interrupts.
- * - PPv2.2:
+ * - PPv2.2 and PPv2.3:
  *   - The old DTs have: "rx-shared", "tx-cpuX" with X in [0...3]
  *   - The new ones have: "hifX" with X in [0..8]
  *
@@ -6621,7 +6621,7 @@ static void mvpp22_rx_fifo_set_hw(struct mvpp2 *priv, int port, int data_size)
 	mvpp2_write(priv, MVPP2_RX_ATTR_FIFO_SIZE_REG(port), attr_size);
 }
 
-/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2 and PPv2.3.
  * 4kB fixed space must be assigned for the loopback port.
  * Redistribute remaining avialable 44kB space among all active ports.
  * Guarantee minimum 32kB for 10G port and 8kB for port 1, capable of 2.5G
@@ -6678,7 +6678,7 @@ static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 	mvpp2_write(priv, MVPP22_TX_FIFO_THRESH_REG(port), threshold);
 }
 
-/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2 and PPv2.3.
  * 3kB fixed space must be assigned for the loopback port.
  * Redistribute remaining avialable 16kB space among all active ports.
  * The 10G interface should use 10kB (which is maximum possible size
@@ -7049,6 +7049,11 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->port_map |= BIT(i);
 	}
 
+	if (priv->hw_version != MVPP21) {
+		if (mvpp2_read(priv, MVPP2_VER_ID_REG) == MVPP2_VER_PP23)
+			priv->hw_version = MVPP23;
+	}
+
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
 	if (err < 0) {
-- 
1.9.1

[PATCH v12 net-next 06/15] net: mvpp2: increase BM pool and RXQ size

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index ce08086..e7bbf0a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -715,8 +715,8 @@
 #define MVPP2_PORT_MAX_RXQ		32
 
 /* Max number of Rx descriptors */
-#define MVPP2_MAX_RXD_MAX		1024
-#define MVPP2_MAX_RXD_DFLT		128
+#define MVPP2_MAX_RXD_MAX		2048
+#define MVPP2_MAX_RXD_DFLT		1024
 
 /* Max number of Tx descriptors */
 #define MVPP2_MAX_TXD_MAX		2048
@@ -848,8 +848,8 @@ enum mvpp22_ptp_packet_format {
 #define MVPP22_PTP_TIMESTAMPQUEUESELECT	BIT(18)
 
 /* BM constants */
-#define MVPP2_BM_JUMBO_BUF_NUM		512
-#define MVPP2_BM_LONG_BUF_NUM		1024
+#define MVPP2_BM_JUMBO_BUF_NUM		2048
+#define MVPP2_BM_LONG_BUF_NUM		2048
 #define MVPP2_BM_SHORT_BUF_NUM		2048
 #define MVPP2_BM_POOL_SIZE_MAX		(16*1024 - MVPP2_BM_POOL_PTR_ALIGN/4)
 #define MVPP2_BM_POOL_PTR_ALIGN		128
-- 
1.9.1

[PATCH v12 net-next 07/15] net: mvpp2: add FCA periodic timer configurations

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 ++++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 45 ++++++++++++++++++++
 2 files changed, 58 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index e7bbf0a..9239d80 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -596,6 +596,15 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
+/* FCA registers. PPv2.2 and PPv2.3 */
+#define MVPP22_FCA_BASE(port)			(0x7600 + (port) * 0x1000)
+#define MVPP22_FCA_REG_SIZE			16
+#define MVPP22_FCA_REG_MASK			0xFFFF
+#define MVPP22_FCA_CONTROL_REG			0x0
+#define MVPP22_FCA_ENABLE_PERIODIC		BIT(11)
+#define MVPP22_PERIODIC_COUNTER_LSB_REG		(0x110)
+#define MVPP22_PERIODIC_COUNTER_MSB_REG		(0x114)
+
 /* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
@@ -751,6 +760,10 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* MSS Flow control */
+#define FC_QUANTA		0xFFFF
+#define FC_CLK_DIVIDER		100
+
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
 	SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 5730900..761f745 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1280,6 +1280,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port)
 	writel(val, mpcs + MVPP22_MPCS_CLK_RESET);
 }
 
+static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 val;
+
+	val = readl(fca + MVPP22_FCA_CONTROL_REG);
+	val &= ~MVPP22_FCA_ENABLE_PERIODIC;
+	if (en)
+		val |= MVPP22_FCA_ENABLE_PERIODIC;
+	writel(val, fca + MVPP22_FCA_CONTROL_REG);
+}
+
+static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 lsb, msb;
+
+	lsb = timer & MVPP22_FCA_REG_MASK;
+	msb = timer >> MVPP22_FCA_REG_SIZE;
+
+	writel(lsb, fca + MVPP22_PERIODIC_COUNTER_LSB_REG);
+	writel(msb, fca + MVPP22_PERIODIC_COUNTER_MSB_REG);
+}
+
+/* Set Flow Control timer x100 faster than pause quanta to ensure that link
+ * partner won't send traffic if port is in XOFF mode.
+ */
+static void mvpp22_gop_fca_set_periodic_timer(struct mvpp2_port *port)
+{
+	u32 timer;
+
+	timer = (port->priv->tclk / (USEC_PER_SEC * FC_CLK_DIVIDER))
+		* FC_QUANTA;
+
+	mvpp22_gop_fca_enable_periodic(port, false);
+
+	mvpp22_gop_fca_set_timer(port, timer);
+
+	mvpp22_gop_fca_enable_periodic(port, true);
+}
+
 static int mvpp22_gop_init(struct mvpp2_port *port)
 {
 	struct mvpp2 *priv = port->priv;
@@ -1324,6 +1367,8 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
 	val |= GENCONF_SOFT_RESET1_GOP;
 	regmap_write(priv->sysctrl_base, GENCONF_SOFT_RESET1, val);
 
+	mvpp22_gop_fca_set_periodic_timer(port);
+
 unsupported_conf:
 	return 0;
 
-- 
1.9.1

[PATCH v12 net-next 08/15] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 ++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 44 ++++++++++++++++----
 2 files changed, 40 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9239d80..d2cc513c 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -295,6 +295,8 @@
 #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK	0x3fc00000
 #define     MVPP2_PON_CAUSE_MISC_SUM_MASK		BIT(31)
 #define MVPP2_ISR_MISC_CAUSE_REG		0x55b0
+#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)	(0x5520 + 4 * (port))
+#define     MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK	0x00ff
 
 /* Buffer Manager registers */
 #define MVPP2_BM_POOL_BASE_REG(pool)		(0x6000 + ((pool) * 4))
@@ -763,6 +765,7 @@
 /* MSS Flow control */
 #define FC_QUANTA		0xFFFF
 #define FC_CLK_DIVIDER		100
+#define MSS_THRESHOLD_STOP	768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 761f745..8b4073c 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1133,14 +1133,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
 static void mvpp2_interrupts_mask(void *arg)
 {
 	struct mvpp2_port *port = arg;
+	int cpu = smp_processor_id();
+	u32 thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu > port->priv->nthreads)
 		return;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
 }
 
 /* Unmask the current thread's Rx/Tx interrupts.
@@ -1150,20 +1155,25 @@ static void mvpp2_interrupts_mask(void *arg)
 static void mvpp2_interrupts_unmask(void *arg)
 {
 	struct mvpp2_port *port = arg;
-	u32 val;
+	int cpu = smp_processor_id();
+	u32 val, thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu > port->priv->nthreads)
 		return;
 
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
 	val = MVPP2_CAUSE_MISC_SUM_MASK |
 		MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
 	if (port->has_tx_irqs)
 		val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+			   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 }
 
 static void
@@ -1188,6 +1198,9 @@ static void mvpp2_interrupts_unmask(void *arg)
 
 		mvpp2_thread_write(port->priv, v->sw_thread_id,
 				   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+		mvpp2_thread_write(port->priv, v->sw_thread_id,
+				   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+				   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 	}
 }
 
@@ -2393,6 +2406,20 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
 	}
 }
 
+/* Set the number of non-occupied descriptors threshold */
+static void mvpp2_set_rxq_free_tresh(struct mvpp2_port *port,
+				     struct mvpp2_rx_queue *rxq)
+{
+	u32 val;
+
+	mvpp2_write(port->priv, MVPP2_RXQ_NUM_REG, rxq->id);
+
+	val = mvpp2_read(port->priv, MVPP2_RXQ_THRESH_REG);
+	val &= ~MVPP2_RXQ_NON_OCCUPIED_MASK;
+	val |= MSS_THRESHOLD_STOP << MVPP2_RXQ_NON_OCCUPIED_OFFSET;
+	mvpp2_write(port->priv, MVPP2_RXQ_THRESH_REG, val);
+}
+
 /* Set the number of packets that will be received before Rx interrupt
  * will be generated by HW.
  */
@@ -2648,6 +2675,9 @@ static int mvpp2_rxq_init(struct mvpp2_port *port,
 	mvpp2_rx_pkts_coal_set(port, rxq);
 	mvpp2_rx_time_coal_set(port, rxq);
 
+	/* Set the number of non occupied descriptors threshold */
+	mvpp2_set_rxq_free_tresh(port, rxq);
+
 	/* Add number of descriptors ready for receiving packets */
 	mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
 
-- 
1.9.1

[PATCH v12 net-next 09/15] net: mvpp2: enable global flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch enables global flow control in FW and in the phylink validate mask.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 11 +++++--
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 30 +++++++++++++++++++-
 2 files changed, 37 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index d2cc513c..8945fb9 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -763,9 +763,11 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define FC_QUANTA		0xFFFF
-#define FC_CLK_DIVIDER		100
-#define MSS_THRESHOLD_STOP	768
+#define MSS_FC_COM_REG			0
+#define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FC_QUANTA			0xFFFF
+#define FC_CLK_DIVIDER			100
+#define MSS_THRESHOLD_STOP		768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
@@ -1017,6 +1019,9 @@ struct mvpp2 {
 
 	/* page_pool allocator */
 	struct page_pool *page_pool[MVPP2_PORT_MAX_RXQ];
+
+	/* Global TX Flow Control config */
+	bool global_tx_fc;
 };
 
 struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 8b4073c..027101b 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -91,6 +91,16 @@ static inline u32 mvpp2_cpu_to_thread(struct mvpp2 *priv, int cpu)
 	return cpu % priv->nthreads;
 }
 
+static void mvpp2_cm3_write(struct mvpp2 *priv, u32 offset, u32 data)
+{
+	writel(data, priv->cm3_base + offset);
+}
+
+static u32 mvpp2_cm3_read(struct mvpp2 *priv, u32 offset)
+{
+	return readl(priv->cm3_base + offset);
+}
+
 static struct page_pool *
 mvpp2_create_page_pool(struct device *dev, int num, int len,
 		       enum dma_data_direction dma_dir)
@@ -5950,6 +5960,11 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 	phylink_set(mask, Autoneg);
 	phylink_set_port_modes(mask);
 
+	if (port->priv->global_tx_fc) {
+		phylink_set(mask, Pause);
+		phylink_set(mask, Asym_Pause);
+	}
+
 	switch (state->interface) {
 	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:
@@ -6951,7 +6966,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err;
+	int err, val;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7003,6 +7018,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 		err = mvpp2_get_sram(pdev, priv);
 		if (err)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
+
+		/* Enable global Flow Control only if handler to SRAM not NULL */
+		if (priv->cm3_base)
+			priv->global_tx_fc = true;
 	}
 
 	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
@@ -7168,6 +7187,15 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+		val |= FLOW_CONTROL_ENABLE_BIT;
+		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+	}
+
 	mvpp2_dbgfs_init(priv, pdev->name);
 
 	platform_set_drvdata(pdev, priv);
-- 
1.9.1

[PATCH v12 net-next 10/15] net: mvpp2: add RXQ flow control configurations

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  35 +++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 116 ++++++++++++++++++++
 2 files changed, 150 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 8945fb9..0010a3e9 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -765,9 +765,36 @@
 /* MSS Flow control */
 #define MSS_FC_COM_REG			0
 #define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FLOW_CONTROL_UPDATE_COMMAND_BIT	BIT(31)
 #define FC_QUANTA			0xFFFF
 #define FC_CLK_DIVIDER			100
-#define MSS_THRESHOLD_STOP		768
+
+#define MSS_RXQ_TRESH_BASE		0x200
+#define MSS_RXQ_TRESH_OFFS		4
+#define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
+					* MSS_RXQ_TRESH_OFFS))
+
+#define MSS_RXQ_TRESH_START_MASK	0xFFFF
+#define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
+#define MSS_RXQ_TRESH_STOP_OFFS		16
+
+#define MSS_RXQ_ASS_BASE	0x80
+#define MSS_RXQ_ASS_OFFS	4
+#define MSS_RXQ_ASS_PER_REG	4
+#define MSS_RXQ_ASS_PER_OFFS	8
+#define MSS_RXQ_ASS_PORTID_OFFS	0
+#define MSS_RXQ_ASS_PORTID_MASK	0x3
+#define MSS_RXQ_ASS_HOSTID_OFFS	2
+#define MSS_RXQ_ASS_HOSTID_MASK	0x3F
+
+#define MSS_RXQ_ASS_Q_BASE(q, fq) ((((q) + (fq)) % MSS_RXQ_ASS_PER_REG)	 \
+				  * MSS_RXQ_ASS_PER_OFFS)
+#define MSS_RXQ_ASS_PQ_BASE(q, fq) ((((q) + (fq)) / MSS_RXQ_ASS_PER_REG) \
+				   * MSS_RXQ_ASS_OFFS)
+#define MSS_RXQ_ASS_REG(q, fq) (MSS_RXQ_ASS_BASE + MSS_RXQ_ASS_PQ_BASE(q, fq))
+
+#define MSS_THRESHOLD_STOP	768
+#define MSS_THRESHOLD_START	1024
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
@@ -1022,6 +1049,9 @@ struct mvpp2 {
 
 	/* Global TX Flow Control config */
 	bool global_tx_fc;
+
+	/* Spinlocks for CM3 shared memory configuration */
+	spinlock_t mss_spinlock;
 };
 
 struct mvpp2_pcpu_stats {
@@ -1184,6 +1214,9 @@ struct mvpp2_port {
 	bool rx_hwtstamp;
 	enum hwtstamp_tx_types tx_hwtstamp_type;
 	struct mvpp2_hwtstamp_queue tx_hwtstamp_queue[2];
+
+	/* Firmware TX flow control */
+	bool tx_fc;
 };
 
 /* The mvpp2_tx_desc and mvpp2_rx_desc structures describe the
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 027101b..f1770e5 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -741,6 +741,110 @@ static void *mvpp2_buf_alloc(struct mvpp2_port *port,
 	return data;
 }
 
+/* Routine enable flow control for RXQs condition */
+static void mvpp2_rxq_enable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, host_id, q;
+	int fq = port->first_rxq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control was enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Set same Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set stop and start Flow control RXQ thresholds */
+		val = MSS_THRESHOLD_START;
+		val |= (MSS_THRESHOLD_STOP << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+		/* Set RXQ port ID */
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val |= (port->id << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		/* Calculate RXQ host ID:
+		 * In Single queue mode: Host ID equal to Host ID used for
+		 *			 shared RX interrupt
+		 * In Multi queue mode: Host ID equal to number of
+		 *			RXQ ID / number of CoS queues
+		 * In Single resource mode: Host ID always equal to 0
+		 */
+		if (queue_mode == MVPP2_QDIST_SINGLE_MODE)
+			host_id = port->nqvecs;
+		else if (queue_mode == MVPP2_QDIST_MULTI_MODE)
+			host_id = q;
+		else
+			host_id = 0;
+
+		/* Set RXQ host ID */
+		val |= (host_id << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
+/* Routine disable flow control for RXQs condition */
+static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, q;
+	unsigned long flags;
+	int fq = port->first_rxq;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control was enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Disable Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set threshold 0 to disable Flow control */
+		val = 0;
+		val |= (0 << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -3005,6 +3109,9 @@ static void mvpp2_cleanup_rxqs(struct mvpp2_port *port)
 
 	for (queue = 0; queue < port->nrxqs; queue++)
 		mvpp2_rxq_deinit(port, port->rxqs[queue]);
+
+	if (port->tx_fc)
+		mvpp2_rxq_disable_fc(port);
 }
 
 /* Init all Rx queues for port */
@@ -3017,6 +3124,10 @@ static int mvpp2_setup_rxqs(struct mvpp2_port *port)
 		if (err)
 			goto err_cleanup;
 	}
+
+	if (port->tx_fc)
+		mvpp2_rxq_enable_fc(port);
+
 	return 0;
 
 err_cleanup:
@@ -4316,6 +4427,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
 
 	if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
 		new_rx_pending = MVPP2_MAX_RXD_MAX;
+	else if (ring->rx_pending < MSS_THRESHOLD_START)
+		new_rx_pending = MSS_THRESHOLD_START;
 	else if (!IS_ALIGNED(ring->rx_pending, 16))
 		new_rx_pending = ALIGN(ring->rx_pending, 16);
 
@@ -7148,6 +7261,9 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->hw_version = MVPP23;
 	}
 
+	/* Init mss lock */
+	spin_lock_init(&priv->mss_spinlock);
+
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
 	if (err < 0) {
-- 
1.9.1

[PATCH v12 net-next 11/15] net: mvpp2: add ethtool flow control configuration support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 +++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 98 ++++++++++++++++++++
 2 files changed, 111 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0010a3e9..0731dc7 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -774,6 +774,19 @@
 #define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
 					* MSS_RXQ_TRESH_OFFS))
 
+#define MSS_BUF_POOL_BASE		0x40
+#define MSS_BUF_POOL_OFFS		4
+#define MSS_BUF_POOL_REG(id)		(MSS_BUF_POOL_BASE		\
+					+ (id) * MSS_BUF_POOL_OFFS)
+
+#define MSS_BUF_POOL_STOP_MASK		0xFFF
+#define MSS_BUF_POOL_START_MASK		(0xFFF << MSS_BUF_POOL_START_OFFS)
+#define MSS_BUF_POOL_START_OFFS		12
+#define MSS_BUF_POOL_PORTS_MASK		(0xF << MSS_BUF_POOL_PORTS_OFFS)
+#define MSS_BUF_POOL_PORTS_OFFS		24
+#define MSS_BUF_POOL_PORT_OFFS(id)	(0x1 <<				\
+					((id) + MSS_BUF_POOL_PORTS_OFFS))
+
 #define MSS_RXQ_TRESH_START_MASK	0xFFFF
 #define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
 #define MSS_RXQ_TRESH_STOP_OFFS		16
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index f1770e5..90c9265 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -845,6 +845,59 @@ static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+/* Routine disable/enable flow control for BM pool condition */
+static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
+				    struct mvpp2_bm_pool *pool,
+				    bool en)
+{
+	int val, cm3_state;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Check if BM pool should be enabled/disable */
+	if (en) {
+		/* Set BM pool start and stop thresholds per port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val |= MSS_BUF_POOL_PORT_OFFS(port->id);
+		val &= ~MSS_BUF_POOL_START_MASK;
+		val |= (MSS_THRESHOLD_START << MSS_BUF_POOL_START_OFFS);
+		val &= ~MSS_BUF_POOL_STOP_MASK;
+		val |= MSS_THRESHOLD_STOP;
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	} else {
+		/* Remove BM pool from the port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val &= ~MSS_BUF_POOL_PORT_OFFS(port->id);
+
+		/* Zero BM pool start and stop thresholds to disable pool
+		 * flow control if pool empty (not used by any port)
+		 */
+		if (!pool->buf_num) {
+			val &= ~MSS_BUF_POOL_START_MASK;
+			val &= ~MSS_BUF_POOL_STOP_MASK;
+		}
+
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -1175,6 +1228,16 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		new_long_pool = MVPP2_BM_LONG;
 
 	if (new_long_pool != port->pool_long->id) {
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port,
+							port->pool_short,
+							false);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							false);
+		}
+
 		/* Remove port from old short & long pool */
 		port->pool_long = mvpp2_bm_pool_use(port, port->pool_long->id,
 						    port->pool_long->pkt_size);
@@ -1192,6 +1255,25 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		mvpp2_swf_bm_pool_init(port);
 
 		mvpp2_set_hw_csum(port, new_long_pool);
+
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							true);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_short,
+							true);
+		}
+
+		/* Update L4 checksum when jumbo enable/disable on port */
+		if (new_long_pool == MVPP2_BM_JUMBO && port->id != 0) {
+			dev->features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
+			dev->hw_features &= ~(NETIF_F_IP_CSUM |
+					      NETIF_F_IPV6_CSUM);
+		} else {
+			dev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+			dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+		}
 	}
 
 out_set:
@@ -6357,6 +6439,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 	u32 val;
+	int i;
 
 	if (mvpp2_is_xlg(interface)) {
 		if (!phylink_autoneg_inband(mode)) {
@@ -6407,6 +6490,21 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
+	if (port->priv->global_tx_fc) {
+		port->tx_fc = tx_pause;
+		if (tx_pause)
+			mvpp2_rxq_enable_fc(port);
+		else
+			mvpp2_rxq_disable_fc(port);
+		if (port->priv->percpu_pools) {
+			for (i = 0; i < port->nrxqs; i++)
+				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i], tx_pause);
+		} else {
+			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
+			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
+		}
+	}
+
 	mvpp2_port_enable(port);
 
 	mvpp2_egress_enable(port);
-- 
1.9.1

[PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  8 +++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 35 +++++++++++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0731dc7..9b525b60 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@
 #define     MVPP2_BM_HIGH_THRESH_MASK		0x7f0000
 #define     MVPP2_BM_HIGH_THRESH_VALUE(val)	((val) << \
 						MVPP2_BM_HIGH_THRESH_OFFS)
+#define     MVPP2_BM_BPPI_HIGH_THRESH		0x1E
+#define     MVPP2_BM_BPPI_LOW_THRESH		0x1C
+#define     MVPP23_BM_BPPI_HIGH_THRESH		0x34
+#define     MVPP23_BM_BPPI_LOW_THRESH		0x28
 #define MVPP2_BM_INTR_CAUSE_REG(pool)		(0x6240 + ((pool) * 4))
 #define     MVPP2_BM_RELEASED_DELAY_MASK	BIT(0)
 #define     MVPP2_BM_ALLOC_FAILED_MASK		BIT(1)
@@ -352,6 +356,10 @@
 #define MVPP2_OVERRUN_ETH_DROP			0x7000
 #define MVPP2_CLS_ETH_DROP			0x7020
 
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG	0x6310
+#define     MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK	0xff
+#define     MVPP23_BM_8POOL_MODE		BIT(8)
+
 /* Hit counters registers */
 #define MVPP2_CTRS_IDX				0x7040
 #define     MVPP22_CTRS_TX_CTR(port, txq)	((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 90c9265..3faad04 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -69,6 +69,11 @@ enum mvpp2_bm_pool_log_num {
 module_param(queue_mode, int, 0444);
 MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
 
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
 /* Utility/helper methods */
 
 void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)
@@ -423,6 +428,21 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 
 	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
 	val |= MVPP2_BM_START_MASK;
+
+	val &= ~MVPP2_BM_LOW_THRESH_MASK;
+	val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+	/* Set 8 Pools BPPI threshold if BM underrun protection feature
+	 * was enabled
+	 */
+	if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+	} else {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+	}
+
 	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
 
 	bm_pool->size = size;
@@ -591,6 +611,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
 	return err;
 }
 
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+	val |= MVPP23_BM_8POOL_MODE;
+	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -644,6 +674,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 	if (!priv->bm_pools)
 		return -ENOMEM;
 
+	if (priv->hw_version == MVPP23 && bm_underrun_protect)
+		mvpp23_bm_set_8pool_mode(priv);
+
 	err = mvpp2_bm_pools_init(dev, priv);
 	if (err < 0)
 		return err;
@@ -6490,7 +6523,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
-	if (port->priv->global_tx_fc) {
+	if (port->priv->global_tx_fc && bm_underrun_protect) {
 		port->tx_fc = tx_pause;
 		if (tx_pause)
 			mvpp2_rxq_enable_fc(port);
-- 
1.9.1

[PATCH v12 net-next 13/15] net: mvpp2: add PPv23 RX FIFO flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 15 ++++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 53 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9b525b60..b61a1ba 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -770,6 +770,18 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* RX FIFO threshold in 1KB granularity */
+#define MVPP23_PORT0_FIFO_TRSH	(9 * 1024)
+#define MVPP23_PORT1_FIFO_TRSH	(4 * 1024)
+#define MVPP23_PORT2_FIFO_TRSH	(2 * 1024)
+
+/* RX Flow Control Registers */
+#define MVPP2_RX_FC_REG(port)		(0x150 + 4 * (port))
+#define     MVPP2_RX_FC_EN		BIT(24)
+#define     MVPP2_RX_FC_TRSH_OFFS	16
+#define     MVPP2_RX_FC_TRSH_MASK	(0xFF << MVPP2_RX_FC_TRSH_OFFS)
+#define     MVPP2_RX_FC_TRSH_UNIT	256
+
 /* MSS Flow control */
 #define MSS_FC_COM_REG			0
 #define FLOW_CONTROL_ENABLE_BIT		BIT(0)
@@ -1498,6 +1510,8 @@ struct mvpp2_bm_pool {
 
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
 
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
+
 #ifdef CONFIG_MVPP2_PTP
 int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
 void mvpp22_tai_tstamp(struct mvpp2_tai *tai, u32 tstamp,
@@ -1530,4 +1544,5 @@ static inline bool mvpp22_rx_hwtstamping(struct mvpp2_port *port)
 {
 	return IS_ENABLED(CONFIG_MVPP2_PTP) && port->rx_hwtstamp;
 }
+
 #endif
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 3faad04..a472125 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6536,6 +6536,8 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
 			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
 		}
+		if (port->priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_en(port->priv, port->id, tx_pause);
 	}
 
 	mvpp2_port_enable(port);
@@ -7004,6 +7006,55 @@ static void mvpp22_rx_fifo_init(struct mvpp2 *priv)
 	mvpp2_write(priv, MVPP2_RX_FIFO_INIT_REG, 0x1);
 }
 
+/* Configure Rx FIFO Flow control thresholds */
+static void mvpp23_rx_fifo_fc_set_tresh(struct mvpp2 *priv)
+{
+	int port, val;
+
+	/* Port 0: maximum speed -10Gb/s port
+	 *	   required by spec RX FIFO threshold 9KB
+	 * Port 1: maximum speed -5Gb/s port
+	 *	   required by spec RX FIFO threshold 4KB
+	 * Port 2: maximum speed -1Gb/s port
+	 *	   required by spec RX FIFO threshold 2KB
+	 */
+
+	/* Without loopback port */
+	for (port = 0; port < (MVPP2_MAX_PORTS - 1); port++) {
+		if (port == 0) {
+			val = (MVPP23_PORT0_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else if (port == 1) {
+			val = (MVPP23_PORT1_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else {
+			val = (MVPP23_PORT2_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		}
+	}
+}
+
+/* Configure Rx FIFO Flow control thresholds */
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP2_RX_FC_REG(port));
+
+	if (en)
+		val |= MVPP2_RX_FC_EN;
+	else
+		val &= ~MVPP2_RX_FC_EN;
+
+	mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+}
+
 static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 {
 	int threshold = MVPP2_TX_FIFO_THRESHOLD(size);
@@ -7155,6 +7206,8 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	} else {
 		mvpp22_rx_fifo_init(priv);
 		mvpp22_tx_fifo_init(priv);
+		if (priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_set_tresh(priv);
 	}
 
 	if (priv->hw_version == MVPP21)
-- 
1.9.1

[PATCH v12 net-next 14/15] net: mvpp2: set 802.3x GoP Flow Control mode

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a472125..4d0a398 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6283,7 +6283,7 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
-	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
+	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_FLOW_CTRL_MASK);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {
-- 
1.9.1

[PATCH v12 net-next 15/15] net: mvpp2: add TX FC firmware check

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  1 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 39 ++++++++++++++++----
 2 files changed, 33 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index b61a1ba..da87152 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -828,6 +828,7 @@
 
 #define MSS_THRESHOLD_STOP	768
 #define MSS_THRESHOLD_START	1024
+#define MSS_FC_MAX_TIMEOUT	5000
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 4d0a398..ac2f442 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -931,6 +931,34 @@ static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+static int mvpp2_enable_global_fc(struct mvpp2 *priv)
+{
+	int val, timeout = 0;
+
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	/* Check if Firmware running and disable FC if not*/
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	while (timeout < MSS_FC_MAX_TIMEOUT) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+
+		if (!(val & FLOW_CONTROL_UPDATE_COMMAND_BIT))
+			return 0;
+		usleep_range(10, 20);
+		timeout++;
+	}
+
+	priv->global_tx_fc = false;
+	return -EOPNOTSUPP;
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -7263,7 +7291,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err, val;
+	int err;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7487,13 +7515,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
-	/* Enable global flow control. In this stage global
-	 * flow control enabled, but still disabled per port.
-	 */
 	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
-		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
-		val |= FLOW_CONTROL_ENABLE_BIT;
-		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+		err = mvpp2_enable_global_fc(priv);
+		if (err)
+			dev_warn(&pdev->dev, "Minimum of CM3 firmware 18.09 and chip revision B0 required for flow control\n");
 	}
 
 	mvpp2_dbgfs_init(priv, pdev->name);
-- 
1.9.1

Re: [PATCH v12 net-next 01/15] doc: marvell: add CM3 address space and PPv2.3 description

[Rob Herring]

On Wed, 10 Feb 2021 11:48:06 +0200, stefanc@marvell.com wrote:
> From: Stefan Chulski <stefanc@marvell.com>
> 
> Patch adds CM3 address space and PPv2.3 description.
> 
> Signed-off-by: Stefan Chulski <stefanc@marvell.com>
> Acked-by: Marcin Wojtas <mw@semihalf.com>
> ---
>  Documentation/devicetree/bindings/net/marvell-pp2.txt | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[David Miller]

From: <stefanc@marvell.com>
Date: Wed, 10 Feb 2021 11:48:17 +0200

>  
> +static int bm_underrun_protect = 1;
> +
> +module_param(bm_underrun_protect, int, 0444);
> +MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");

No new module parameters, please.

RE: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Stefan Chulski]

> 
> ----------------------------------------------------------------------
> From: <stefanc@marvell.com>
> Date: Wed, 10 Feb 2021 11:48:17 +0200
> 
> >
> > +static int bm_underrun_protect = 1;
> > +
> > +module_param(bm_underrun_protect, int, 0444);
> > +MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect
> > +feature (0-1), def=1");
> 
> No new module parameters, please.

Ok, I would remove new module parameters.
By the way why new module parameters forbitten?

Thanks,
Stefan

Re: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Andrew Lunn]

On Thu, Feb 11, 2021 at 08:22:19AM +0000, Stefan Chulski wrote:
> 
> > 
> > ----------------------------------------------------------------------
> > From: <stefanc@marvell.com>
> > Date: Wed, 10 Feb 2021 11:48:17 +0200
> > 
> > >
> > > +static int bm_underrun_protect = 1;
> > > +
> > > +module_param(bm_underrun_protect, int, 0444);
> > > +MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect
> > > +feature (0-1), def=1");
> > 
> > No new module parameters, please.
> 
> Ok, I would remove new module parameters.
> By the way why new module parameters forbitten?

Historically, module parameters are a bad interface for
configuration. Vendors have stuffed all sorts of random junk into
module parameters. There is little documentation. Different drivers
can have similar looking module parameters which do different
things. Or different module parameters, which actually do the same
thing. But maybe with slightly different parameters.

We get a much better overall result if you stop and think for a
while. How can this be made a generic configuration knob which
multiple vendors could use? And then add it to ethtool. Extend the
ethtool -h text and the man page. Maybe even hack some other vendors
driver to make use of it.

Or we have also found out, that pushing back on parameters like this,
the developers goes back and looks at the code, and sometimes figures
out a way to automatically do the right thing, removing the
configuration knob, and just making it all simpler for the user to
use.

       Andrew

Re: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Marcin Wojtas]

Hi,

czw., 11 lut 2021 o 15:19 Andrew Lunn <andrew@lunn.ch> napisał(a):
>
> On Thu, Feb 11, 2021 at 08:22:19AM +0000, Stefan Chulski wrote:
> >
> > >
> > > ----------------------------------------------------------------------
> > > From: <stefanc@marvell.com>
> > > Date: Wed, 10 Feb 2021 11:48:17 +0200
> > >
> > > >
> > > > +static int bm_underrun_protect = 1;
> > > > +
> > > > +module_param(bm_underrun_protect, int, 0444);
> > > > +MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect
> > > > +feature (0-1), def=1");
> > >
> > > No new module parameters, please.
> >
> > Ok, I would remove new module parameters.
> > By the way why new module parameters forbitten?
>
> Historically, module parameters are a bad interface for
> configuration. Vendors have stuffed all sorts of random junk into
> module parameters. There is little documentation. Different drivers
> can have similar looking module parameters which do different
> things. Or different module parameters, which actually do the same
> thing. But maybe with slightly different parameters.
>
> We get a much better overall result if you stop and think for a
> while. How can this be made a generic configuration knob which
> multiple vendors could use? And then add it to ethtool. Extend the
> ethtool -h text and the man page. Maybe even hack some other vendors
> driver to make use of it.
>
> Or we have also found out, that pushing back on parameters like this,
> the developers goes back and looks at the code, and sometimes figures
> out a way to automatically do the right thing, removing the
> configuration knob, and just making it all simpler for the user to
> use.

I think of 2 alternatives:
* `ethtool --set-priv-flags` - in such case there is a question if
switching this particular feature in runtime is a good idea.
* New DT/ACPI property - it is a hardware feature after all, so maybe
let the user decide whether to enable it on the platform description
level.

What do you think?

Best regards,
Marcin

Re: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Andrew Lunn]

> > Or we have also found out, that pushing back on parameters like this,
> > the developers goes back and looks at the code, and sometimes figures
> > out a way to automatically do the right thing, removing the
> > configuration knob, and just making it all simpler for the user to
> > use.
> 
> I think of 2 alternatives:
> * `ethtool --set-priv-flags` - in such case there is a question if
> switching this particular feature in runtime is a good idea.
> * New DT/ACPI property - it is a hardware feature after all, so maybe
> let the user decide whether to enable it on the platform description
> level.

Does this even need to be configurable? What is the cost of turning it
on? How does having less pools affect the system? Does average latency
go up?  When would i consider an underrun actually a good thing?

Maybe it should just be hard coded on? Or we should try to detect when
underruns are happening a lot, and dynamically turn it on for a while?

	  Andrew

RE: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Stefan Chulski]

> > > Or we have also found out, that pushing back on parameters like
> > > this, the developers goes back and looks at the code, and sometimes
> > > figures out a way to automatically do the right thing, removing the
> > > configuration knob, and just making it all simpler for the user to
> > > use.
> >
> > I think of 2 alternatives:
> > * `ethtool --set-priv-flags` - in such case there is a question if
> > switching this particular feature in runtime is a good idea.
> > * New DT/ACPI property - it is a hardware feature after all, so maybe
> > let the user decide whether to enable it on the platform description
> > level.
> 
> Does this even need to be configurable? What is the cost of turning it on?
> How does having less pools affect the system? Does average latency go up?
> When would i consider an underrun actually a good thing?
> 
> Maybe it should just be hard coded on? Or we should try to detect when
> underruns are happening a lot, and dynamically turn it on for a while?
> 
> 	  Andrew

The cost of this change is that the number of pools reduced from 16 to 8.
The current driver uses only 4pools, but some future features like QoS can use over 4 pools. 

Regards,
Stefan. 

Re: [EXT] Re: [PATCH v12 net-next 12/15] net: mvpp2: add BM protection underrun feature support

[Andrew Lunn]

> > Does this even need to be configurable? What is the cost of turning it on?
> > How does having less pools affect the system? Does average latency go up?
> > When would i consider an underrun actually a good thing?
> > 
> > Maybe it should just be hard coded on? Or we should try to detect when
> > underruns are happening a lot, and dynamically turn it on for a while?
> > 
> The cost of this change is that the number of pools reduced from 16 to 8.
> The current driver uses only 4pools, but some future features like QoS can use over 4 pools. 

So you are saying, there is currently no cost for turning it on. So it
seems like you should just turn it on, and forget the module
parameter. When QoS features are added which require more than 8 pools
you can then address the issue of if this should be configurable.

    Andrew