From: satya priya <skakit@codeaurora.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: mka@chromium.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
kgunda@codeaurora.org, satya priya <skakit@codeaurora.org>
Subject: [RESEND PATCH V3 4/5] arm64: dts: qcom: pmk8350: Add PMIC peripherals for pmk8350
Date: Wed, 14 Apr 2021 16:43:00 +0530 [thread overview]
Message-ID: <1618398783-7834-3-git-send-email-skakit@codeaurora.org> (raw)
In-Reply-To: <1618398783-7834-1-git-send-email-skakit@codeaurora.org>
Add PON, RTC and other PMIC infra modules support for PMK8350.
Signed-off-by: satya priya <skakit@codeaurora.org>
---
arch/arm64/boot/dts/qcom/pmk8350.dtsi | 55 ++++++++++++++++++++++++++++++++++-
1 file changed, 54 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/pmk8350.dtsi b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
index 1530b8f..bbd9fa7 100644
--- a/arch/arm64/boot/dts/qcom/pmk8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
@@ -3,6 +3,12 @@
* Copyright (c) 2021, Linaro Limited
*/
+#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735b.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
@@ -13,10 +19,57 @@
#address-cells = <1>;
#size-cells = <0>;
+ pmk8350_pon: pon@1300 {
+ compatible = "qcom,pm8998-pon";
+ reg = <0x1300>;
+
+ pwrkey {
+ compatible = "qcom,pmk8350-pwrkey";
+ interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ };
+
+ resin {
+ compatible = "qcom,pmk8350-resin";
+ interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ pmk8350_vadc: adc@3100 {
+ compatible = "qcom,spmi-adc7";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "eoc-int-en-set";
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ };
+
+ pmk8350_adc_tm: adc-tm@3400 {
+ compatible = "qcom,adc-tm7";
+ reg = <0x3400>;
+ interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "threshold";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #thermal-sensor-cells = <1>;
+ status = "disabled";
+ };
+
+ pmk8350_rtc: rtc@6100 {
+ compatible = "qcom,pmk8350-rtc";
+ reg = <0x6100>, <0x6200>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+ };
+
pmk8350_gpios: gpio@b000 {
- compatible = "qcom,pmk8350-gpio";
+ compatible = "qcom,pmk8350-gpio", "qcom,spmi-gpio";
reg = <0xb000>;
gpio-controller;
+ gpio-ranges = <&pmk8350_gpios 0 0 4>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2021-04-14 11:13 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-14 11:12 [RESEND PATCH V3 0/5] Add PMIC DT files for sc7280 satya priya
2021-04-14 11:12 ` [RESEND PATCH V3 1/5] arm64: dts: qcom: pm7325: Add pm7325 base dts file satya priya
2021-04-14 11:13 ` satya priya [this message]
2021-04-20 17:29 ` [RESEND PATCH V3 4/5] arm64: dts: qcom: pmk8350: Add PMIC peripherals for pmk8350 Matthias Kaehlcke
2021-04-28 5:58 ` skakit
2021-04-14 11:13 ` [RESEND PATCH V3 3/5] arm64: dts: qcom: pmr735a: Add temp-alarm support satya priya
2021-04-20 17:16 ` Matthias Kaehlcke
2021-04-14 11:13 ` [RESEND PATCH V3 2/5] arm64: dts: qcom: pm8350c: " satya priya
2021-04-14 11:13 ` [RESEND PATCH V3 5/5] arm64: dts: qcom: sc7280: Include PMIC DT files for sc7280 satya priya
2021-04-20 18:02 ` Matthias Kaehlcke
2021-04-28 6:04 ` skakit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1618398783-7834-3-git-send-email-skakit@codeaurora.org \
--to=skakit@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=kgunda@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).