linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Guangbin Huang <huangguangbin2@huawei.com>
To: <davem@davemloft.net>, <kuba@kernel.org>
Cc: <netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<salil.mehta@huawei.com>, <lipeng321@huawei.com>,
	<huangguangbin2@huawei.com>
Subject: [PATCH net-next 1/5] net: hns3: add support for handling all errors through MSI-X
Date: Tue, 8 Jun 2021 21:08:27 +0800	[thread overview]
Message-ID: <1623157711-26846-2-git-send-email-huangguangbin2@huawei.com> (raw)
In-Reply-To: <1623157711-26846-1-git-send-email-huangguangbin2@huawei.com>

From: Yufeng Mo <moyufeng@huawei.com>

Currently, hardware errors can be reported through AER or MSI-X mode.
However, the AER mode is intended to handle only bus errors, but not
hardware errors. On the other hand, virtual machines cannot handle
AER errors. When an AER error is reported, virtual machines will be
suspended. So add support for handling all these hardware errors
through MSI-X mode which depends on a newer version of firmware,
and reserve the handler of the AER mode for compatibility.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
---
 .../net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c | 16 ++++++++
 .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c    | 47 +++++++++++-----------
 .../ethernet/hisilicon/hns3/hns3pf/hclge_main.h    |  1 +
 3 files changed, 41 insertions(+), 23 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c
index f125aa425872..540dd15d7771 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c
@@ -1611,11 +1611,27 @@ static const struct hclge_hw_blk hw_blk[] = {
 	{ /* sentinel */ }
 };
 
+static void hclge_config_all_msix_error(struct hclge_dev *hdev, bool enable)
+{
+	u32 reg_val;
+
+	reg_val = hclge_read_dev(&hdev->hw, HCLGE_PF_OTHER_INT_REG);
+
+	if (enable)
+		reg_val |= BIT(HCLGE_VECTOR0_ALL_MSIX_ERR_B);
+	else
+		reg_val &= ~BIT(HCLGE_VECTOR0_ALL_MSIX_ERR_B);
+
+	hclge_write_dev(&hdev->hw, HCLGE_PF_OTHER_INT_REG, reg_val);
+}
+
 int hclge_config_nic_hw_error(struct hclge_dev *hdev, bool state)
 {
 	const struct hclge_hw_blk *module = hw_blk;
 	int ret = 0;
 
+	hclge_config_all_msix_error(hdev, state);
+
 	while (module->name) {
 		if (module->config_err_int) {
 			ret = module->config_err_int(hdev, state);
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index 45102681bd2a..d5be3bc50b5c 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -3307,11 +3307,13 @@ static int hclge_set_vf_link_state(struct hnae3_handle *handle, int vf,
 
 static u32 hclge_check_event_cause(struct hclge_dev *hdev, u32 *clearval)
 {
-	u32 cmdq_src_reg, msix_src_reg;
+	u32 cmdq_src_reg, msix_src_reg, hw_err_src_reg;
 
 	/* fetch the events from their corresponding regs */
 	cmdq_src_reg = hclge_read_dev(&hdev->hw, HCLGE_VECTOR0_CMDQ_SRC_REG);
 	msix_src_reg = hclge_read_dev(&hdev->hw, HCLGE_MISC_VECTOR_INT_STS);
+	hw_err_src_reg = hclge_read_dev(&hdev->hw,
+					HCLGE_RAS_PF_OTHER_INT_STS_REG);
 
 	/* Assumption: If by any chance reset and mailbox events are reported
 	 * together then we will only process reset event in this go and will
@@ -3339,11 +3341,11 @@ static u32 hclge_check_event_cause(struct hclge_dev *hdev, u32 *clearval)
 		return HCLGE_VECTOR0_EVENT_RST;
 	}
 
-	/* check for vector0 msix event source */
-	if (msix_src_reg & HCLGE_VECTOR0_REG_MSIX_MASK) {
-		*clearval = msix_src_reg;
+	/* check for vector0 msix event and hardware error event source */
+	if (msix_src_reg & HCLGE_VECTOR0_REG_MSIX_MASK ||
+	    hw_err_src_reg & HCLGE_RAS_REG_NFE_MASK ||
+	    hw_err_src_reg & HCLGE_RAS_REG_ROCEE_ERR_MASK)
 		return HCLGE_VECTOR0_EVENT_ERR;
-	}
 
 	/* check for vector0 mailbox(=CMDQ RX) event source */
 	if (BIT(HCLGE_VECTOR0_RX_CMDQ_INT_B) & cmdq_src_reg) {
@@ -3354,9 +3356,8 @@ static u32 hclge_check_event_cause(struct hclge_dev *hdev, u32 *clearval)
 
 	/* print other vector0 event source */
 	dev_info(&hdev->pdev->dev,
-		 "CMDQ INT status:0x%x, other INT status:0x%x\n",
-		 cmdq_src_reg, msix_src_reg);
-	*clearval = msix_src_reg;
+		 "INT status: CMDQ(%#x) HW errors(%#x) other(%#x)\n",
+		 cmdq_src_reg, hw_err_src_reg, msix_src_reg);
 
 	return HCLGE_VECTOR0_EVENT_OTHER;
 }
@@ -3427,15 +3428,10 @@ static irqreturn_t hclge_misc_irq_handle(int irq, void *data)
 
 	hclge_clear_event_cause(hdev, event_cause, clearval);
 
-	/* Enable interrupt if it is not cause by reset. And when
-	 * clearval equal to 0, it means interrupt status may be
-	 * cleared by hardware before driver reads status register.
-	 * For this case, vector0 interrupt also should be enabled.
-	 */
-	if (!clearval ||
-	    event_cause == HCLGE_VECTOR0_EVENT_MBX) {
+	/* Enable interrupt if it is not caused by reset event or error event */
+	if (event_cause == HCLGE_VECTOR0_EVENT_MBX ||
+	    event_cause == HCLGE_VECTOR0_EVENT_OTHER)
 		hclge_enable_vector(&hdev->misc_vector, true);
-	}
 
 	return IRQ_HANDLED;
 }
@@ -4244,22 +4240,27 @@ static void hclge_misc_err_recovery(struct hclge_dev *hdev)
 {
 	struct hnae3_ae_dev *ae_dev = pci_get_drvdata(hdev->pdev);
 	struct device *dev = &hdev->pdev->dev;
+	enum hnae3_reset_type reset_type;
 	u32 msix_sts_reg;
 
 	msix_sts_reg = hclge_read_dev(&hdev->hw, HCLGE_MISC_VECTOR_INT_STS);
-
 	if (msix_sts_reg & HCLGE_VECTOR0_REG_MSIX_MASK) {
-		if (hclge_handle_hw_msix_error(hdev,
-					       &hdev->default_reset_request))
+		if (hclge_handle_hw_msix_error
+				(hdev, &hdev->default_reset_request))
 			dev_info(dev, "received msix interrupt 0x%x\n",
 				 msix_sts_reg);
+	}
+	hclge_enable_vector(&hdev->misc_vector, true);
 
-		if (hdev->default_reset_request)
-			if (ae_dev->ops->reset_event)
-				ae_dev->ops->reset_event(hdev->pdev, NULL);
+	hclge_handle_hw_ras_error(ae_dev);
+	if (ae_dev->hw_err_reset_req) {
+		reset_type = hclge_get_reset_level(ae_dev,
+						   &ae_dev->hw_err_reset_req);
+		hclge_set_def_reset_request(ae_dev, reset_type);
 	}
 
-	hclge_enable_vector(&hdev->misc_vector, true);
+	if (hdev->default_reset_request && ae_dev->ops->reset_event)
+		ae_dev->ops->reset_event(hdev->pdev, NULL);
 }
 
 static void hclge_errhand_service_task(struct hclge_dev *hdev)
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
index 9b8abb5d7a8e..582972a6f60e 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
@@ -190,6 +190,7 @@ enum HLCGE_PORT_TYPE {
 #define HCLGE_VECTOR0_IMP_RESET_INT_B	1
 #define HCLGE_VECTOR0_IMP_CMDQ_ERR_B	4U
 #define HCLGE_VECTOR0_IMP_RD_POISON_B	5U
+#define HCLGE_VECTOR0_ALL_MSIX_ERR_B	6U
 
 #define HCLGE_MAC_DEFAULT_FRAME \
 	(ETH_HLEN + ETH_FCS_LEN + 2 * VLAN_HLEN + ETH_DATA_LEN)
-- 
2.8.1


  reply	other threads:[~2021-06-08 13:11 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-08 13:08 [PATCH net-next 0/5] net: hns3: add RAS compatibility adaptation solution Guangbin Huang
2021-06-08 13:08 ` Guangbin Huang [this message]
2021-06-08 13:08 ` [PATCH net-next 2/5] net: hns3: add the " Guangbin Huang
2021-06-08 13:08 ` [PATCH net-next 3/5] net: hns3: add support for imp-handle ras capability Guangbin Huang
2021-06-08 13:08 ` [PATCH net-next 4/5] net: hns3: update error recovery module and type Guangbin Huang
2021-06-08 13:08 ` [PATCH net-next 5/5] net: hns3: add error handling compatibility during initialization Guangbin Huang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1623157711-26846-2-git-send-email-huangguangbin2@huawei.com \
    --to=huangguangbin2@huawei.com \
    --cc=davem@davemloft.net \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lipeng321@huawei.com \
    --cc=netdev@vger.kernel.org \
    --cc=salil.mehta@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).