From: Rajesh Patil <rajpat@codeaurora.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, rnayak@codeaurora.org,
saiprakash.ranjan@codeaurora.org, msavaliy@qti.qualcomm.com,
skakit@codeaurora.org, Roja Rani Yarubandi <rojay@codeaurora.org>,
Rajesh Patil <rajpat@codeaurora.org>
Subject: [PATCH V4 1/4] arm64: dts: sc7280: Add QSPI node
Date: Mon, 26 Jul 2021 19:10:44 +0530 [thread overview]
Message-ID: <1627306847-25308-2-git-send-email-rajpat@codeaurora.org> (raw)
In-Reply-To: <1627306847-25308-1-git-send-email-rajpat@codeaurora.org>
From: Roja Rani Yarubandi <rojay@codeaurora.org>
Add QSPI DT node for SC7280 SoC.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
---
Changes in V4:
- As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
qspi_opp_table from /soc to / (root).
Changes in V3:
- Broken the huge V2 patch into 3 smaller patches.
1. QSPI DT nodes
2. QUP wrapper_0 DT nodes
3. QUP wrapper_1 DT nodes
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 27 ++++++++++++++
arch/arm64/boot/dts/qcom/sc7280.dtsi | 62 +++++++++++++++++++++++++++++++++
2 files changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 73225e3..b0bfd8e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -269,6 +269,20 @@
};
};
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <37500000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -346,6 +360,19 @@
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+&qspi_cs0 {
+ bias-disable;
+};
+
+&qspi_clk {
+ bias-disable;
+};
+
+&qspi_data01 {
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+};
+
&qup_uart5_default {
tx {
pins = "gpio46";
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 5764c5b..ca6e36b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
method = "smc";
};
+ qspi_opp_table: qspi-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-150000000 {
+ opp-hz = /bits/ 64 <150000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
@@ -1301,6 +1320,24 @@
};
};
+ qspi: spi@88dc000 {
+ compatible = "qcom,qspi-v1";
+ reg = <0 0x088dc000 0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+ clock-names = "iface", "core";
+ interconnects = <&gem_noc MASTER_APPSS_PROC 0
+ &cnoc2 SLAVE_QSPI_0 0>;
+ interconnect-names = "qspi-config";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qspi_opp_table>;
+ status = "disabled";
+
+ };
+
dc_noc: interconnect@90e0000 {
reg = <0 0x090e0000 0 0x5080>;
compatible = "qcom,sc7280-dc-noc";
@@ -1492,6 +1529,31 @@
gpio-ranges = <&tlmm 0 0 175>;
wakeup-parent = <&pdc>;
+ qspi_clk: qspi-clk {
+ pins = "gpio14";
+ function = "qspi_clk";
+ };
+
+ qspi_cs0: qspi-cs0 {
+ pins = "gpio15";
+ function = "qspi_cs";
+ };
+
+ qspi_cs1: qspi-cs1 {
+ pins = "gpio19";
+ function = "qspi_cs";
+ };
+
+ qspi_data01: qspi-data01 {
+ pins = "gpio12", "gpio13";
+ function = "qspi_data";
+ };
+
+ qspi_data12: qspi-data12 {
+ pins = "gpio16", "gpio17";
+ function = "qspi_data";
+ };
+
qup_uart5_default: qup-uart5-default {
pins = "gpio46", "gpio47";
function = "qup13";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2021-07-26 13:42 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-26 13:40 [PATCH V4 0/4] Add QSPI and QUPv3 DT nodes for SC7280 SoC Rajesh Patil
2021-07-26 13:40 ` Rajesh Patil [this message]
2021-07-26 16:07 ` [PATCH V4 1/4] arm64: dts: sc7280: Add QSPI node Matthias Kaehlcke
2021-08-11 12:14 ` rajpat
2021-07-26 13:40 ` [PATCH V4 2/4] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes Rajesh Patil
2021-07-26 16:02 ` Matthias Kaehlcke
2021-08-11 12:13 ` rajpat
2021-08-11 14:52 ` Matthias Kaehlcke
2021-08-12 7:13 ` rajpat
2021-08-12 12:49 ` Matthias Kaehlcke
2021-07-27 19:20 ` Stephen Boyd
2021-08-11 12:17 ` rajpat
2021-07-26 13:40 ` [PATCH V4 3/4] arm64: dts: sc7280: Update QUPv3 Debug UART DT node Rajesh Patil
2021-07-26 15:42 ` Matthias Kaehlcke
2021-08-11 12:04 ` rajpat
2021-07-26 13:40 ` [PATCH V4 4/4] arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes Rajesh Patil
2021-07-27 0:14 ` [PATCH V4 0/4] Add QSPI and QUPv3 DT nodes for SC7280 SoC Stephen Boyd
2021-08-11 12:14 ` rajpat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1627306847-25308-2-git-send-email-rajpat@codeaurora.org \
--to=rajpat@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=msavaliy@qti.qualcomm.com \
--cc=rnayak@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=rojay@codeaurora.org \
--cc=saiprakash.ranjan@codeaurora.org \
--cc=skakit@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).