From: Baolin Wang <baolin.wang@linaro.org>
To: sre@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com
Cc: linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, yuanjiang.yu@unisoc.com,
baolin.wang@linaro.org, broonie@kernel.org
Subject: [PATCH 1/2] dt-bindings: power: Add Spreadtrum SC27XX fuel gauge unit documentation
Date: Wed, 12 Sep 2018 15:29:38 +0800 [thread overview]
Message-ID: <1b3f165e2a806dd3d4b7712160ee3bda72f7d675.1536736399.git.baolin.wang@linaro.org> (raw)
This patch adds the binding documentation for Spreadtrum SC27XX series PMICs
fuel gauge unit device, which is used to calculate the battery capacity.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
---
.../devicetree/bindings/power/supply/sc27xx-fg.txt | 55 ++++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
new file mode 100644
index 0000000..7447bae
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt
@@ -0,0 +1,55 @@
+Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings
+
+Required properties:
+- compatible: Should be one of the following:
+ "sprd,sc2720-fgu",
+ "sprd,sc2721-fgu",
+ "sprd,sc2723-fgu",
+ "sprd,sc2730-fgu",
+ "sprd,sc2731-fgu".
+- reg: The address offset of fuel gauge unit.
+- bat-detect-gpio: GPIO for battery detection.
+- io-channels: Specify the IIO ADC channel to get temperature.
+- io-channel-names: Should be "bat-temp".
+- sprd,inner-resist: Specify the the battery inner resistance (mOhm).
+- sprd,ocv-cap-table: Provide the battery capacity percent with corresponding
+ open circuit voltage (ocv) of the battery, which is used to look up current
+ battery capacity according to current baterry ocv values.
+- monitored-battery: Phandle of battery characteristics devicetree node.
+ The fuel gauge uses the following battery properties:
+- charge-full-design-microamp-hours: battery design capacity.
+- constant-charge-voltage-max-microvolt: maximum constant input voltage.
+ See Documentation/devicetree/bindings/power/supply/battery.txt
+
+Example:
+
+ bat: battery {
+ compatible = "simple-battery";
+ charge-full-design-microamp-hours = <1900000>;
+ constant-charge-voltage-max-microvolt = <4350000>;
+ ......
+ };
+
+ sc2731_pmic: pmic@0 {
+ compatible = "sprd,sc2731";
+ reg = <0>;
+ spi-max-frequency = <26000000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fgu@a00 {
+ compatible = "sprd,sc2731-fgu";
+ reg = <0xa00>;
+ bat-detect-gpio = <&pmic_eic 9 GPIO_ACTIVE_HIGH>;
+ io-channels = <&pmic_adc 5>;
+ io-channel-names = "bat-temp";
+ sprd,inner-resist = <250>;
+ sprd,ocv-cap-table = <4185 100>, <4113 95>, <4066 90>, <4022 85>, <3983 80>, <3949 75>, <3917 70>,
+ <3889 65>, <3864 60>, <3835 55>, <3805 50>, <3787 45>, <3777 40>, <3773 35>, <3770 30>,
+ <3765 25>, <3752 20>, <3724 15>, <3680 10>, <3605 5>, <3400 0>;
+ monitored-battery = <&bat>;
+ };
+ };
--
1.7.9.5
next reply other threads:[~2018-09-12 7:30 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-09-12 7:29 Baolin Wang [this message]
2018-09-12 7:29 ` [PATCH 2/2] power: supply: Add Spreadtrum SC27XX fuel gauge unit driver Baolin Wang
2018-09-16 14:35 ` Sebastian Reichel
2018-09-17 4:01 ` Baolin Wang
2018-09-20 0:36 ` Sebastian Reichel
2018-09-20 0:40 ` Baolin Wang
2018-09-16 13:57 ` [PATCH 1/2] dt-bindings: power: Add Spreadtrum SC27XX fuel gauge unit documentation Sebastian Reichel
2018-09-17 3:43 ` Baolin Wang
2018-09-20 0:46 ` Sebastian Reichel
2018-09-20 0:53 ` Baolin Wang
[not found] ` <20180917032625.GA25442@bogus>
2018-09-17 20:45 ` Baolin Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1b3f165e2a806dd3d4b7712160ee3bda72f7d675.1536736399.git.baolin.wang@linaro.org \
--to=baolin.wang@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=sre@kernel.org \
--cc=yuanjiang.yu@unisoc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).