From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <bgolaszewski@baylibre.com>,
Alessandro Zummo <a.zummo@towertech.it>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-power@fi.rohmeurope.com, linux-clk@vger.kernel.org,
linux-gpio@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [PATCH v2 05/17] dt_bindings: bd71828: Add clock output mode
Date: Tue, 19 Jan 2021 09:16:23 +0200 [thread overview]
Message-ID: <1b6077ad08f7eacdac6604439d0921778d6046db.1611037866.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1611037866.git.matti.vaittinen@fi.rohmeurope.com>
The BD71828 allows configuring the clk32kout pin mode to CMOS or
open-drain. Add device-tree property for specifying the preferred mode.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
Changes from v1:
switched clk-mode property from string type to tristated one as
suggested by Rob.
.../devicetree/bindings/mfd/rohm,bd71828-pmic.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
index 3a6a1a26e2b3..8380166d176c 100644
--- a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
@@ -44,6 +44,12 @@ properties:
clock-output-names:
const: bd71828-32k-out
+ rohm,clkout-open-drain:
+ description: clk32kout mode. Set to 1 for "open-drain" or 0 for "cmos".
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1
+
rohm,charger-sense-resistor-ohms:
minimum: 10000000
maximum: 50000000
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
next prev parent reply other threads:[~2021-01-19 7:20 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-19 7:13 [PATCH v2 00/17] Support ROHM BD71815 PMIC Matti Vaittinen
2021-01-19 7:14 ` [PATCH v2 01/17] regulator: bd718x7, bd71828, Fix dvs voltage levels Matti Vaittinen
2021-01-19 7:14 ` [PATCH v2 02/17] rtc: bd70528: Do not require parent data Matti Vaittinen
2021-01-19 21:09 ` Alexandre Belloni
2021-01-20 6:37 ` Matti Vaittinen
2021-01-19 7:15 ` [PATCH v2 03/17] clk: BD718x7: Do not depend on parent driver data Matti Vaittinen
2021-01-19 7:15 ` [PATCH v2 04/17] mfd: bd718x7: simplify by cleaning unnecessary device data Matti Vaittinen
2021-01-25 13:56 ` Lee Jones
2021-01-19 7:16 ` Matti Vaittinen [this message]
2021-02-09 2:22 ` [PATCH v2 05/17] dt_bindings: bd71828: Add clock output mode Rob Herring
2021-01-19 7:17 ` [PATCH v2 06/17] dt_bindings: regulator: Add ROHM BD71815 PMIC regulators Matti Vaittinen
2021-02-09 2:24 ` Rob Herring
2021-02-09 13:10 ` Vaittinen, Matti
2021-02-09 13:50 ` Rob Herring
2021-01-19 7:21 ` [PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC Matti Vaittinen
2021-02-09 2:26 ` Rob Herring
2021-01-19 7:21 ` [PATCH v2 08/17] mfd: Add ROHM BD71815 ID Matti Vaittinen
2021-01-25 13:57 ` Lee Jones
2021-01-19 7:22 ` [PATCH v2 09/17] mfd: Support for ROHM BD71815 PMIC core Matti Vaittinen
2021-01-25 14:10 ` Lee Jones
2021-01-25 14:48 ` Matti Vaittinen
2021-01-26 8:29 ` Lee Jones
2021-01-19 7:23 ` [PATCH v2 10/17] gpio: support ROHM BD71815 GPOs Matti Vaittinen
2021-01-19 11:07 ` Bartosz Golaszewski
2021-01-19 13:01 ` Vaittinen, Matti
2021-03-23 9:57 ` Vaittinen, Matti
2021-03-26 14:44 ` Bartosz Golaszewski
2021-01-19 7:25 ` [PATCH v2 11/17] regulator: helpers: Export helper voltage listing Matti Vaittinen
2021-01-19 7:26 ` [PATCH v2 12/17] regulator: rohm-regulator: linear voltage support Matti Vaittinen
2021-01-19 7:27 ` [PATCH v2 13/17] regulator: rohm-regulator: Support SNVS HW state Matti Vaittinen
2021-01-19 7:29 ` [PATCH v2 14/17] regulator: Support ROHM BD71815 regulators Matti Vaittinen
2021-01-19 7:30 ` [PATCH v2 15/17] clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC Matti Vaittinen
2021-02-12 3:40 ` Stephen Boyd
2021-01-19 7:31 ` [PATCH v2 16/17] rtc: bd70528: Support RTC on ROHM BD71815 Matti Vaittinen
2021-01-19 21:10 ` Alexandre Belloni
2021-01-19 7:34 ` [PATCH v2 17/17] MAINTAINERS: Add ROHM BD71815AGW Matti Vaittinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1b6077ad08f7eacdac6604439d0921778d6046db.1611037866.git.matti.vaittinen@fi.rohmeurope.com \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@bootlin.com \
--cc=bgolaszewski@baylibre.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-power@fi.rohmeurope.com \
--cc=linux-rtc@vger.kernel.org \
--cc=mazziesaccount@gmail.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).