From: "Andrew Jeffery" <andrew@aj.id.au>
To: "Steven Lee" <steven_lee@aspeedtech.com>,
"Linus Walleij" <linus.walleij@linaro.org>,
"Bartosz Golaszewski" <bgolaszewski@baylibre.com>,
"Rob Herring" <robh+dt@kernel.org>,
"Joel Stanley" <joel@jms.id.au>,
"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
"moderated list:ARM/ASPEED MACHINE SUPPORT"
<linux-arm-kernel@lists.infradead.org>,
"moderated list:ARM/ASPEED MACHINE SUPPORT"
<linux-aspeed@lists.ozlabs.org>,
"open list" <linux-kernel@vger.kernel.org>
Cc: "Hongwei Zhang" <Hongweiz@ami.com>,
"Ryan Chen" <ryan_chen@aspeedtech.com>,
"Billy Tsai" <billy_tsai@aspeedtech.com>
Subject: Re: [PATCH v5 01/10] dt-bindings: aspeed-sgpio: Convert txt bindings to yaml.
Date: Wed, 09 Jun 2021 10:12:33 +0930 [thread overview]
Message-ID: <1f34af33-0905-480e-8a55-e5e34d66216f@www.fastmail.com> (raw)
In-Reply-To: <20210608102547.4880-2-steven_lee@aspeedtech.com>
On Tue, 8 Jun 2021, at 19:55, Steven Lee wrote:
> sgpio-aspeed bindings should be converted to yaml format.
>
> Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
> ---
> .../bindings/gpio/aspeed,sgpio.yaml | 75 +++++++++++++++++++
> .../devicetree/bindings/gpio/sgpio-aspeed.txt | 46 ------------
> 2 files changed, 75 insertions(+), 46 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml
> delete mode 100644 Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml
> b/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml
> new file mode 100644
> index 000000000000..b2ae211411ff
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml
> @@ -0,0 +1,75 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Aspeed SGPIO controller
> +
> +maintainers:
> + - Andrew Jeffery <andrew@aj.id.au>
> +
> +description:
> + This SGPIO controller is for ASPEED AST2500 SoC, it supports up to
> 80 full
> + featured Serial GPIOs. Each of the Serial GPIO pins can be
> programmed to
> + support the following options
> + - Support interrupt option for each input port and various interrupt
> + sensitivity option (level-high, level-low, edge-high, edge-low)
> + - Support reset tolerance option for each output port
> + - Directly connected to APB bus and its shift clock is from APB bus
> clock
> + divided by a programmable value.
> + - Co-work with external signal-chained TTL components
> (74LV165/74LV595)
> +
> +properties:
> + compatible:
> + enum:
> + - aspeed,ast2400-sgpio
> + - aspeed,ast2500-sgpio
> +
> + reg:
> + maxItems: 1
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + interrupts:
> + maxItems: 1
> +
> + interrupt-controller: true
> +
> + clocks:
> + maxItems: 1
> +
> + ngpios: true
> +
> + bus-frequency: true
I'm not familiar enough with dt-schema to know that this does what we need, so deferring to Rob.
Looks good otherwise.
Andrew
next prev parent reply other threads:[~2021-06-09 0:43 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-08 10:25 [PATCH v5 00/10] ASPEED sgpio driver enhancement Steven Lee
2021-06-08 10:25 ` [PATCH v5 01/10] dt-bindings: aspeed-sgpio: Convert txt bindings to yaml Steven Lee
2021-06-09 0:42 ` Andrew Jeffery [this message]
2021-06-10 16:18 ` Rob Herring
2021-06-08 10:25 ` [PATCH v5 02/10] dt-bindings: aspeed-sgpio: Add ast2600 sgpio compatibles Steven Lee
2021-06-10 16:23 ` Rob Herring
2021-06-10 23:27 ` Andrew Jeffery
2021-06-16 15:20 ` Rob Herring
2021-06-08 10:25 ` [PATCH v5 03/10] ARM: dts: aspeed-g6: Add SGPIO node Steven Lee
2021-06-09 0:43 ` Andrew Jeffery
2021-06-09 1:51 ` Steven Lee
2021-06-09 2:19 ` Andrew Jeffery
2021-06-08 10:25 ` [PATCH v5 04/10] ARM: dts: aspeed-g5: Remove ngpios from sgpio node Steven Lee
2021-06-09 0:45 ` Andrew Jeffery
2021-06-08 10:25 ` [PATCH v5 05/10] gpio: gpio-aspeed-sgpio: Add AST2600 sgpio support Steven Lee
2021-06-09 0:52 ` Andrew Jeffery
2021-06-08 10:25 ` [PATCH v5 06/10] gpio: gpio-aspeed-sgpio: Add AST2400 and AST2500 platform data Steven Lee
2021-06-09 0:55 ` Andrew Jeffery
2021-06-09 4:12 ` Steven Lee
2021-06-09 6:45 ` Andrew Jeffery
2021-06-11 19:02 ` Bartosz Golaszewski
2021-06-15 4:22 ` Steven Lee
2021-06-08 10:25 ` [PATCH v5 07/10] gpio: gpio-aspeed-sgpio: Add set_config function Steven Lee
2021-06-08 10:25 ` [PATCH v5 08/10] gpio: gpio-aspeed-sgpio: Move irq_chip to aspeed-sgpio struct Steven Lee
2021-06-08 10:25 ` [PATCH v5 09/10] gpio: gpio-aspeed-sgpio: Use generic device property APIs Steven Lee
2021-06-08 10:25 ` [PATCH v5 10/10] gpio: gpio-aspeed-sgpio: Return error if ngpios is not multiple of 8 Steven Lee
2021-06-09 0:56 ` Andrew Jeffery
2021-06-09 10:54 ` [PATCH v5 00/10] ASPEED sgpio driver enhancement Linus Walleij
2021-06-10 2:24 ` Steven Lee
2021-06-10 7:50 ` Linus Walleij
2021-06-10 8:39 ` Steven Lee
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1f34af33-0905-480e-8a55-e5e34d66216f@www.fastmail.com \
--to=andrew@aj.id.au \
--cc=Hongweiz@ami.com \
--cc=bgolaszewski@baylibre.com \
--cc=billy_tsai@aspeedtech.com \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=ryan_chen@aspeedtech.com \
--cc=steven_lee@aspeedtech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).