LKML Archive on lore.kernel.org
 help / color / Atom feed
From: Jerome Brunet <jbrunet@baylibre.com>
To: Remi Pommarel <repk@triplefau.lt>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Yue Wang <yue.wang@Amlogic.com>,
	Kevin Hilman <khilman@baylibre.com>,
	Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
	Bjorn Helgaas <bhelgaas@google.com>,
	Neil Armstrong <narmstrong@baylibre.com>,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
	Rob Herring <robh+dt@kernel.org>
Cc: linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org
Subject: Re: [PATCH v5 5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver
Date: Thu, 23 Jan 2020 10:37:57 +0100
Message-ID: <1j1rrqwm16.fsf@starbuckisacylon.baylibre.com> (raw)
In-Reply-To: <20200116111850.23690-6-repk@triplefau.lt>


On Thu 16 Jan 2020 at 12:18, Remi Pommarel <repk@triplefau.lt> wrote:

> This adds support for the MIPI analog PHY which is also used for PCIE
> found in the Amlogic AXG SoC Family.
>
> MIPI or PCIE selection is done by the #phy-cells, making the mode
> static and exclusive.
>
> For now only PCIE fonctionality is supported.
>
> This PHY will be used to replace the mipi_enable clock gating logic
> which was mistakenly added in the clock subsystem. This also activate
> a non documented band gap bit in those registers that allows reliable
> PCIE clock signal generation on AXG platforms.
>

I don't the phy subsystem much but this looks sane and aligned with what
was discussed for this Amlogic SoC.

Thanks for this Remi !

Acked-by: Jerome Brunet <jbrunet@baylibre.com>

> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> ---
>  drivers/phy/amlogic/Kconfig                   |  11 +
>  drivers/phy/amlogic/Makefile                  |  11 +-
>  .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
>  3 files changed, 205 insertions(+), 5 deletions(-)
>  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
>
> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> index af774ac2b934..8c9cf2403591 100644
> --- a/drivers/phy/amlogic/Kconfig
> +++ b/drivers/phy/amlogic/Kconfig
> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
>  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
>  	  in Meson G12A SoCs.
>  	  If unsure, say N.
> +
> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> +	tristate "Meson AXG MIPI + PCIE analog PHY driver"
> +	default ARCH_MESON
> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> +	select GENERIC_PHY
> +	select REGMAP_MMIO
> +	help
> +	  Enable this to support the Meson MIPI + PCIE analog PHY
> +	  found in Meson AXG SoCs.
> +	  If unsure, say N.
> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> index 11d1c42ac2be..0aecf92d796a 100644
> --- a/drivers/phy/amlogic/Makefile
> +++ b/drivers/phy/amlogic/Makefile
> @@ -1,6 +1,7 @@
>  # SPDX-License-Identifier: GPL-2.0-only
> -obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
> -obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
> +obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> new file mode 100644
> index 000000000000..1431cbf885e1
> --- /dev/null
> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> @@ -0,0 +1,188 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Amlogic AXG MIPI + PCIE analog PHY driver
> + *
> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
> + */
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define HHI_MIPI_CNTL0 0x00
> +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
> +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
> +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
> +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
> +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
> +
> +#define HHI_MIPI_CNTL1 0x01
> +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
> +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
> +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
> +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
> +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
> +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
> +
> +#define HHI_MIPI_CNTL2 0x02
> +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
> +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
> +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
> +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
> +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
> +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
> +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
> +
> +struct phy_axg_mipi_pcie_analog_priv {
> +	struct phy *phy;
> +	unsigned int mode;
> +	struct regmap *regmap;
> +};
> +
> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
> +	.reg_bits = 8,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +	.max_register = HHI_MIPI_CNTL2,
> +};
> +
> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> +
> +	/* MIPI not supported yet */
> +	if (priv->mode != PHY_TYPE_PCIE)
> +		return -EINVAL;
> +
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_BANDGAP, 0);
> +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> +			   HHI_MIPI_CNTL0_ENABLE, 0);
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
> +{
> +	return 0;
> +}
> +
> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
> +	.init = phy_axg_mipi_pcie_analog_init,
> +	.exit = phy_axg_mipi_pcie_analog_exit,
> +	.power_on = phy_axg_mipi_pcie_analog_power_on,
> +	.power_off = phy_axg_mipi_pcie_analog_power_off,
> +	.owner = THIS_MODULE,
> +};
> +
> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
> +						  struct of_phandle_args *args)
> +{
> +	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
> +	unsigned int mode;
> +
> +	if (args->args_count != 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	mode = args->args[0];
> +
> +	/* MIPI mode is not supported yet */
> +	if (mode != PHY_TYPE_PCIE) {
> +		dev_err(dev, "invalid phy mode select argument\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	priv->mode = mode;
> +	return priv->phy;
> +}
> +
> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
> +{
> +	struct phy_provider *phy;
> +	struct device *dev = &pdev->dev;
> +	struct phy_axg_mipi_pcie_analog_priv *priv;
> +	struct device_node *np = dev->of_node;
> +	struct regmap *map;
> +	struct resource *res;
> +	void __iomem *base;
> +	int ret;
> +
> +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(base)) {
> +		dev_err(dev, "failed to get regmap base\n");
> +		return PTR_ERR(base);
> +	}
> +
> +	map = devm_regmap_init_mmio(dev, base,
> +				    &phy_axg_mipi_pcie_analog_regmap_conf);
> +	if (IS_ERR(map)) {
> +		dev_err(dev, "failed to get HHI regmap\n");
> +		return PTR_ERR(map);
> +	}
> +	priv->regmap = map;
> +
> +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
> +	if (IS_ERR(priv->phy)) {
> +		ret = PTR_ERR(priv->phy);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "failed to create PHY\n");
> +		return ret;
> +	}
> +
> +	phy_set_drvdata(priv->phy, priv);
> +	dev_set_drvdata(dev, priv);
> +
> +	phy = devm_of_phy_provider_register(dev,
> +					    phy_axg_mipi_pcie_analog_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy);
> +}
> +
> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
> +	{
> +		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
> +
> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
> +	.probe = phy_axg_mipi_pcie_analog_probe,
> +	.driver = {
> +		.name = "phy-axg-mipi-pcie-analog",
> +		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
> +	},
> +};
> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
> +
> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
> +MODULE_LICENSE("GPL v2");


  reply index

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-16 11:18 [PATCH v5 0/7] PCI: amlogic: Make PCIe working reliably on AXG platforms Remi Pommarel
2020-01-16 11:18 ` [PATCH v5 1/7] dt-bindings: Add AXG PCIE PHY bindings Remi Pommarel
2020-01-17 16:03   ` Rob Herring
2020-01-16 11:18 ` [PATCH v5 2/7] dt-bindings: Add AXG shared MIPI/PCIE analog " Remi Pommarel
2020-01-17 16:04   ` Rob Herring
2020-01-16 11:18 ` [PATCH v5 3/7] dt-bindings: PCI: meson: Update PCIE bindings documentation Remi Pommarel
2020-01-17 16:05   ` Rob Herring
2020-01-16 11:18 ` [PATCH v5 4/7] arm64: dts: meson-axg: Add PCIE PHY nodes Remi Pommarel
2020-01-23  9:56   ` Neil Armstrong
2020-01-16 11:18 ` [PATCH v5 5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver Remi Pommarel
2020-01-23  9:37   ` Jerome Brunet [this message]
2020-01-16 11:18 ` [PATCH v5 6/7] phy: amlogic: Add Amlogic AXG PCIE " Remi Pommarel
2020-01-23  9:44   ` Jerome Brunet
2020-01-23 10:56     ` Remi Pommarel
2020-01-16 11:18 ` [PATCH v5 7/7] PCI: amlogic: Use AXG PCIE Remi Pommarel
2020-01-16 20:13   ` Bjorn Helgaas
2020-01-23 10:00     ` Neil Armstrong
2020-01-23  9:52   ` Jerome Brunet

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1j1rrqwm16.fsf@starbuckisacylon.baylibre.com \
    --to=jbrunet@baylibre.com \
    --cc=bhelgaas@google.com \
    --cc=devicetree@vger.kernel.org \
    --cc=khilman@baylibre.com \
    --cc=kishon@ti.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=narmstrong@baylibre.com \
    --cc=repk@triplefau.lt \
    --cc=robh+dt@kernel.org \
    --cc=yue.wang@Amlogic.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

LKML Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/lkml/0 lkml/git/0.git
	git clone --mirror https://lore.kernel.org/lkml/1 lkml/git/1.git
	git clone --mirror https://lore.kernel.org/lkml/2 lkml/git/2.git
	git clone --mirror https://lore.kernel.org/lkml/3 lkml/git/3.git
	git clone --mirror https://lore.kernel.org/lkml/4 lkml/git/4.git
	git clone --mirror https://lore.kernel.org/lkml/5 lkml/git/5.git
	git clone --mirror https://lore.kernel.org/lkml/6 lkml/git/6.git
	git clone --mirror https://lore.kernel.org/lkml/7 lkml/git/7.git
	git clone --mirror https://lore.kernel.org/lkml/8 lkml/git/8.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 lkml lkml/ https://lore.kernel.org/lkml \
		linux-kernel@vger.kernel.org
	public-inbox-index lkml

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git