* [DRIVER] patch against 2.4.6pre8
@ 2001-07-03 1:22 Linux A2232 Driver Project
0 siblings, 0 replies; only message in thread
From: Linux A2232 Driver Project @ 2001-07-03 1:22 UTC (permalink / raw)
To: linux-kernel
Hallo!
This is the patch for the A2232 multi-serial board again,
as a patch against 2.4.6pre8. Should be convenient for
Linus to include :)
Greetings,
Enver
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/CREDITS linux-2.4.6-pre8-withA2232/CREDITS
--- linux-2.4.6-pre8-vanilla/CREDITS Tue Jul 3 01:42:49 2001
+++ linux-2.4.6-pre8-withA2232/CREDITS Tue Jul 3 02:17:29 2001
@@ -1056,6 +1056,11 @@
S: 2400 AG, Alphen aan den Rijn
S: The Netherlands
+N: Enver Haase
+E: ehaase@inf.fu-berlin.de
+W: http://www.inf.fu-berlin.de/~ehaase
+D: Driver for the Commodore A2232 serial board
+
N: Bruno Haible
E: haible@ma2s2.mathematik.uni-karlsruhe.de
D: SysV FS, shm swapping, memory management fixes
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/Documentation/Configure.help linux-2.4.6-pre8-withA2232/Documentation/Configure.help
--- linux-2.4.6-pre8-vanilla/Documentation/Configure.help Tue Jul 3 01:42:49 2001
+++ linux-2.4.6-pre8-withA2232/Documentation/Configure.help Tue Jul 3 02:29:22 2001
@@ -16738,6 +16738,21 @@
If you want to compile it as a module, say M here and read
Documentation/modules.txt.
+Commodore A2232 serial support
+CONFIG_A2232
+ This option supports the 2232 7-port serial card designed for the
+ Amiga 2000 and other Zorro-bus machines. At a maximum of 19,200 bps,
+ the ports are served by a 6551 ACIA UART chip each, plus a 8520 CIA,
+ and a master 65EC02 CPU and buffer as well. The ports are connected
+ with 8 pin mini-DIN connectors on the card bracket, for which 8 pin
+ to DB25 adapters are supplied. The card also has jumpers internally
+ to toggle various pinning configurations.
+
+ This driver can be built as a module; but then "generic_serial.o"
+ will also be built as a module. This has to be loaded before
+ "ser_a2232.o". If you want to do this, answer M here and read
+ "<file:Documentation/modules.txt>".
+
Atari DMA sound support
CONFIG_DMASOUND_ATARI
If you want to use the internal audio of your Atari in Linux, answer
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/MAINTAINERS linux-2.4.6-pre8-withA2232/MAINTAINERS
--- linux-2.4.6-pre8-vanilla/MAINTAINERS Tue Jul 3 01:42:50 2001
+++ linux-2.4.6-pre8-withA2232/MAINTAINERS Tue Jul 3 02:41:10 2001
@@ -106,6 +106,13 @@
L: linux-net@vger.kernel.org
S: Maintained
+A2232 SERIAL BOARD DRIVER
+P: Enver Haase
+M: ehaase@inf.fu-berlin.de
+M: A2232@gmx.net
+L: linux-m68k@lists.linux-m68k.org
+S: Maintained
+
ACI MIXER DRIVER
P: Robert Siemer
M: Robert.Siemer@gmx.de
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/Config.in linux-2.4.6-pre8-withA2232/drivers/char/Config.in
--- linux-2.4.6-pre8-vanilla/drivers/char/Config.in Wed Mar 7 04:44:34 2001
+++ linux-2.4.6-pre8-withA2232/drivers/char/Config.in Tue Jul 3 02:34:44 2001
@@ -60,6 +60,9 @@
tristate ' Stallion EC8/64, ONboard, Brumby support' CONFIG_ISTALLION
fi
fi
+if [ "$CONFIG_EXPERIMENTAL" = "y" -a "$CONFIG_ZORRO" = "y" ]; then
+ tristate 'Commodore A2232 serial support (EXPERIMENTAL)' CONFIG_A2232
+fi
if [ "$CONFIG_FOOTBRIDGE" = "y" ]; then
bool 'DC21285 serial port support' CONFIG_SERIAL_21285
if [ "$CONFIG_SERIAL_21285" = "y" ]; then
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/Makefile linux-2.4.6-pre8-withA2232/drivers/char/Makefile
--- linux-2.4.6-pre8-vanilla/drivers/char/Makefile Wed May 16 19:27:02 2001
+++ linux-2.4.6-pre8-withA2232/drivers/char/Makefile Tue Jul 3 02:31:16 2001
@@ -139,6 +139,7 @@
obj-$(CONFIG_N_HDLC) += n_hdlc.o
obj-$(CONFIG_SPECIALIX) += specialix.o
obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o
+obj-$(CONFIG_A2232) += ser_a2232.o generic_serial.o
obj-$(CONFIG_SX) += sx.o generic_serial.o
obj-$(CONFIG_RIO) += rio/rio.o generic_serial.o
obj-$(CONFIG_SH_SCI) += sh-sci.o generic_serial.o
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232.c linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232.c
--- linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232.c Thu Jan 1 01:00:00 1970
+++ linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232.c Tue Jul 3 02:50:45 2001
@@ -0,0 +1,878 @@
+/* drivers/char/ser_a2232.c */
+
+/* $Id: ser_a2232.c,v 0.4 2000/01/25 12:00:00 ehaase Exp $ */
+
+/* Linux serial driver for the Amiga A2232 board */
+
+/* This driver is MAINTAINED. Before applying any changes, please contact
+ * the author.
+ */
+
+/* Copyright (c) 2000-2001 Enver Haase <ehaase@inf.fu-berlin.de>
+ * alias The A2232 driver project <A2232@gmx.net>
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+/***************************** Documentation ************************/
+/*
+ * This driver is in EXPERIMENTAL state. That means I could not find
+ * someone with five A2232 boards with 35 ports running at 19200 bps
+ * at the same time and test the machine's behaviour.
+ * However, I know that you can performance-tweak this driver (see
+ * the source code).
+ * One thing to consider is the time this driver consumes during the
+ * Amiga's vertical blank interrupt. Everything that is to be done
+ * _IS DONE_ when entering the vertical blank interrupt handler of
+ * this driver.
+ * However, it would be more sane to only do the job for only ONE card
+ * instead of ALL cards at a time; or, more generally, to handle only
+ * SOME ports instead of ALL ports at a time.
+ * However, as long as no-one runs into problems I guess I shouldn't
+ * change the driver as it runs fine for me :) .
+ *
+ * Version history of this file:
+ * 0.4 Resolved licensing issues.
+ * 0.3 Inclusion in the Linux/m68k tree, small fixes.
+ * 0.2 Added documentation, minor typo fixes.
+ * 0.1 Initial release.
+ *
+ * TO DO:
+ * - Handle incoming BREAK events. I guess "Stevens: Advanced
+ * Programming in the UNIX(R) Environment" is a good reference
+ * on what is to be done.
+ *
+ * THANKS TO:
+ * - Jukka Marin (65EC02 code).
+ * - The other NetBSD developers on whose A2232 driver I had a
+ * pretty close look. However, I didn't copy any code so it
+ * is okay to put my code under the GPL and include it into
+ * Linux.
+ */
+/***************************** End of Documentation *****************/
+
+/***************************** Defines ******************************/
+/*
+ * Enables experimental 115200 (normal) 230400 (turbo) baud rate.
+ * The A2232 specification states it can only operate at speeds up to
+ * 19200 bits per second, and I was not able to send a file via
+ * "sz"/"rz" and a null-modem cable from one A2232 port to another
+ * at 115200 bits per second.
+ * However, this might work for you.
+ */
+#undef A2232_SPEEDHACK
+/*
+ * Default is not to use RTS/CTS so you could be talked to death.
+ */
+#define A2232_SUPPRESS_RTSCTS_WARNING
+/************************* End of Defines ***************************/
+
+/***************************** Includes *****************************/
+#include <linux/module.h>
+
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+
+#include <asm/setup.h>
+#include <asm/amigaints.h>
+#include <asm/amigahw.h>
+#include <linux/zorro.h>
+#include <asm/irq.h>
+#include <asm/semaphore.h>
+
+#include <linux/delay.h>
+
+#include <linux/serial.h>
+#include <linux/generic_serial.h>
+
+#include "ser_a2232.h"
+#include "ser_a2232fw.h"
+/************************* End of Includes **************************/
+
+/***************************** Prototypes ***************************/
+/* Helper functions */
+static __inline__ volatile struct a2232status *a2232stat(unsigned int board,
+ unsigned int portonboard);
+static __inline__ volatile struct a2232memory *a2232mem (unsigned int board);
+static __inline__ void a2232_receive_char( struct a2232_port *port,
+ int ch, int err );
+/* The interrupt service routine */
+static void a2232_vbl_inter(int irq, void *data, struct pt_regs *fp);
+/* Initialize the port structures */
+static void a2232_init_portstructs(void);
+/* Initialize and register TTY drivers. */
+/* returns 0 IFF successful */
+static int a2232_init_drivers(void);
+/* Initialize all A2232 boards; main entry point. */
+int a2232board_init(void);
+
+/* BEGIN GENERIC_SERIAL PROTOTYPES */
+static void a2232_disable_tx_interrupts(void *ptr);
+static void a2232_enable_tx_interrupts(void *ptr);
+static void a2232_disable_rx_interrupts(void *ptr);
+static void a2232_enable_rx_interrupts(void *ptr);
+static int a2232_get_CD(void *ptr);
+static void a2232_shutdown_port(void *ptr);
+static int a2232_set_real_termios(void *ptr);
+static int a2232_chars_in_buffer(void *ptr);
+static void a2232_close(void *ptr);
+static void a2232_hungup(void *ptr);
+/* static void a2232_getserial (void *ptr, struct serial_struct *sp); */
+/* END GENERIC_SERIAL PROTOTYPES */
+
+/* Functions that the TTY driver struct expects */
+static int a2232_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg);
+static void a2232_throttle(struct tty_struct *tty);
+static void a2232_unthrottle(struct tty_struct *tty);
+static int a2232_open(struct tty_struct * tty, struct file * filp);
+/************************* End of Prototypes ************************/
+
+/***************************** Global variables *********************/
+/*---------------------------------------------------------------------------
+ * Interface from generic_serial.c back here
+ *--------------------------------------------------------------------------*/
+static struct real_driver a2232_real_driver = {
+ a2232_disable_tx_interrupts,
+ a2232_enable_tx_interrupts,
+ a2232_disable_rx_interrupts,
+ a2232_enable_rx_interrupts,
+ a2232_get_CD,
+ a2232_shutdown_port,
+ a2232_set_real_termios,
+ a2232_chars_in_buffer,
+ a2232_close,
+ a2232_hungup,
+ NULL /* a2232_getserial */
+};
+
+static void *a2232_driver_ID = &a2232_driver_ID; // Some memory address WE own.
+
+/* Ports structs */
+static struct a2232_port a2232_ports[MAX_A2232_BOARDS*NUMLINES];
+
+/* TTY driver structs */
+static struct tty_driver a2232_driver;
+static struct tty_driver a2232_callout_driver;
+
+/* Variables used by the TTY driver */
+static int a2232_refcount;
+static struct tty_struct *a2232_table[MAX_A2232_BOARDS*NUMLINES] = { NULL, };
+static struct termios *a2232_termios[MAX_A2232_BOARDS*NUMLINES];
+static struct termios *a2232_termios_locked[MAX_A2232_BOARDS*NUMLINES];
+
+/* nr of cards completely (all ports) and correctly configured */
+static int nr_a2232;
+
+/* zorro_dev structs for the A2232's */
+static struct zorro_dev *zd_a2232[MAX_A2232_BOARDS];
+/***************************** End of Global variables **************/
+
+/***************************** Functions ****************************/
+/*** BEGIN OF REAL_DRIVER FUNCTIONS ***/
+
+static void a2232_disable_tx_interrupts(void *ptr)
+{
+ struct a2232_port *port;
+ volatile struct a2232status *stat;
+ unsigned long flags;
+
+ port = ptr;
+ stat = a2232stat(port->which_a2232, port->which_port_on_a2232);
+ stat->OutDisable = -1;
+
+ /* Does this here really have to be? */
+ save_flags(flags);
+ cli();
+ port->gs.flags &= ~GS_TX_INTEN;
+ restore_flags(flags);
+}
+
+static void a2232_enable_tx_interrupts(void *ptr)
+{
+ struct a2232_port *port;
+ volatile struct a2232status *stat;
+ unsigned long flags;
+
+ port = ptr;
+ stat = a2232stat(port->which_a2232, port->which_port_on_a2232);
+ stat->OutDisable = 0;
+
+ /* Does this here really have to be? */
+ save_flags(flags);
+ cli();
+ port->gs.flags |= GS_TX_INTEN;
+ restore_flags(flags);
+}
+
+static void a2232_disable_rx_interrupts(void *ptr)
+{
+ struct a2232_port *port;
+ port = ptr;
+ port->disable_rx = -1;
+}
+
+static void a2232_enable_rx_interrupts(void *ptr)
+{
+ struct a2232_port *port;
+ port = ptr;
+ port->disable_rx = 0;
+}
+
+static int a2232_get_CD(void *ptr)
+{
+ return ((struct a2232_port *) ptr)->cd_status;
+}
+
+static void a2232_shutdown_port(void *ptr)
+{
+ struct a2232_port *port;
+ volatile struct a2232status *stat;
+ unsigned long flags;
+
+ port = ptr;
+ stat = a2232stat(port->which_a2232, port->which_port_on_a2232);
+
+ save_flags(flags);
+ cli();
+
+ port->gs.flags &= ~GS_ACTIVE;
+
+ if (port->gs.tty && port->gs.tty->termios->c_cflag & HUPCL) {
+ /* Set DTR and RTS to Low, flush output.
+ The NetBSD driver "msc.c" does it this way. */
+ stat->Command = ( (stat->Command & ~A2232CMD_CMask) |
+ A2232CMD_Close );
+ stat->OutFlush = -1;
+ stat->Setup = -1;
+ }
+
+ restore_flags(flags);
+
+ /* After analyzing control flow, I think a2232_shutdown_port
+ is actually the last call from the system when at application
+ level someone issues a "echo Hello >>/dev/ttyY0".
+ Therefore I think the MOD_DEC_USE_COUNT should be here and
+ not in "a2232_close()". See the comment in "sx.c", too.
+ If you run into problems, compile this driver into the
+ kernel instead of compiling it as a module. */
+ MOD_DEC_USE_COUNT;
+}
+
+static int a2232_set_real_termios(void *ptr)
+{
+ unsigned int cflag, baud, chsize, stopb, parity, softflow;
+ int rate;
+ int a2232_param, a2232_cmd;
+ unsigned long flags;
+ unsigned int i;
+ struct a2232_port *port = ptr;
+ volatile struct a2232status *status;
+ volatile struct a2232memory *mem;
+
+ if (!port->gs.tty || !port->gs.tty->termios) return 0;
+
+ status = a2232stat(port->which_a2232, port->which_port_on_a2232);
+ mem = a2232mem(port->which_a2232);
+
+ a2232_param = a2232_cmd = 0;
+
+ // get baud rate
+ baud = port->gs.baud;
+ if (baud == 0) {
+ /* speed == 0 -> drop DTR, do nothing else */
+ save_flags(flags);
+ cli();
+ // Clear DTR (and RTS... mhhh).
+ status->Command = ( (status->Command & ~A2232CMD_CMask) |
+ A2232CMD_Close );
+ status->OutFlush = -1;
+ status->Setup = -1;
+
+ restore_flags(flags);
+ return 0;
+ }
+
+ rate = A2232_BAUD_TABLE_NOAVAIL;
+ for (i=0; i < A2232_BAUD_TABLE_NUM_RATES * 3; i += 3){
+ if (a2232_baud_table[i] == baud){
+ if (mem->Common.Crystal == A2232_TURBO) rate = a2232_baud_table[i+2];
+ else rate = a2232_baud_table[i+1];
+ }
+ }
+ if (rate == A2232_BAUD_TABLE_NOAVAIL){
+ printk("a2232: Board %d Port %d unsupported baud rate: %d baud. Using another.\n",port->which_a2232,port->which_port_on_a2232,baud);
+ // This is useful for both (turbo or normal) Crystal versions.
+ rate = A2232PARAM_B9600;
+ }
+ a2232_param |= rate;
+
+ cflag = port->gs.tty->termios->c_cflag;
+
+ // get character size
+ chsize = cflag & CSIZE;
+ switch (chsize){
+ case CS8: a2232_param |= A2232PARAM_8Bit; break;
+ case CS7: a2232_param |= A2232PARAM_7Bit; break;
+ case CS6: a2232_param |= A2232PARAM_6Bit; break;
+ case CS5: a2232_param |= A2232PARAM_5Bit; break;
+ default: printk("a2232: Board %d Port %d unsupported character size: %d. Using 8 data bits.\n",
+ port->which_a2232,port->which_port_on_a2232,chsize);
+ a2232_param |= A2232PARAM_8Bit; break;
+ }
+
+ // get number of stop bits
+ stopb = cflag & CSTOPB;
+ if (stopb){ // two stop bits instead of one
+ printk("a2232: Board %d Port %d 2 stop bits unsupported. Using 1 stop bit.\n",
+ port->which_a2232,port->which_port_on_a2232);
+ }
+
+ // Warn if RTS/CTS not wanted
+ if (!(cflag & CRTSCTS)){
+#ifndef A2232_SUPPRESS_RTSCTS_WARNING
+ printk("a2232: Board %d Port %d cannot switch off firmware-implemented RTS/CTS hardware flow control.\n",
+ port->which_a2232,port->which_port_on_a2232);
+#endif
+ }
+
+ /* I think this is correct.
+ However, IXOFF means _input_ flow control and I wonder
+ if one should care about IXON _output_ flow control,
+ too. If this makes problems, one should turn the A2232
+ firmware XON/XOFF "SoftFlow" flow control off and use
+ the conventional way of inserting START/STOP characters
+ by hand in throttle()/unthrottle().
+ */
+ softflow = !!( port->gs.tty->termios->c_iflag & IXOFF );
+
+ // get Parity (Enabled/Disabled? If Enabled, Odd or Even?)
+ parity = cflag & (PARENB | PARODD);
+ if (parity & PARENB){
+ if (parity & PARODD){
+ a2232_cmd |= A2232CMD_OddParity;
+ }
+ else{
+ a2232_cmd |= A2232CMD_EvenParity;
+ }
+ }
+ else a2232_cmd |= A2232CMD_NoParity;
+
+
+ /* Hmm. Maybe an own a2232_port structure
+ member would be cleaner? */
+ if (cflag & CLOCAL)
+ port->gs.flags &= ~ASYNC_CHECK_CD;
+ else
+ port->gs.flags |= ASYNC_CHECK_CD;
+
+
+ /* Now we have all parameters and can go to set them: */
+ save_flags(flags);
+ cli();
+
+ status->Param = a2232_param | A2232PARAM_RcvBaud;
+ status->Command = a2232_cmd | A2232CMD_Open | A2232CMD_Enable;
+ status->SoftFlow = softflow;
+ status->OutDisable = 0;
+ status->Setup = -1;
+
+ restore_flags(flags);
+ return 0;
+}
+
+static int a2232_chars_in_buffer(void *ptr)
+{
+ struct a2232_port *port;
+ volatile struct a2232status *status;
+ unsigned char ret; /* we need modulo-256 arithmetics */
+ port = ptr;
+ status = a2232stat(port->which_a2232, port->which_port_on_a2232);
+#if A2232_IOBUFLEN != 256
+#error "Re-Implement a2232_chars_in_buffer()!"
+#endif
+ ret = (status->OutHead - status->OutTail);
+ return ret;
+}
+
+static void a2232_close(void *ptr)
+{
+ a2232_disable_tx_interrupts(ptr);
+ a2232_disable_rx_interrupts(ptr);
+ /* see the comment in a2232_shutdown_port above. */
+ /* MOD_DEC_USE_COUNT; */
+}
+
+static void a2232_hungup(void *ptr)
+{
+ a2232_close(ptr);
+}
+/*** END OF REAL_DRIVER FUNCTIONS ***/
+
+/*** BEGIN FUNCTIONS EXPECTED BY TTY DRIVER STRUCTS ***/
+static int a2232_ioctl( struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ return -ENOIOCTLCMD;
+}
+
+static void a2232_throttle(struct tty_struct *tty)
+{
+/* Throttle: System cannot take another chars: Drop RTS or
+ send the STOP char or whatever.
+ The A2232 firmware does RTS/CTS anyway, and XON/XOFF
+ if switched on. So the only thing we can do at this
+ layer here is not taking any characters out of the
+ A2232 buffer any more. */
+ struct a2232_port *port = (struct a2232_port *) tty->driver_data;
+ port->throttle_input = -1;
+}
+
+static void a2232_unthrottle(struct tty_struct *tty)
+{
+/* Unthrottle: dual to "throttle()" above. */
+ struct a2232_port *port = (struct a2232_port *) tty->driver_data;
+ port->throttle_input = 0;
+}
+
+static int a2232_open(struct tty_struct * tty, struct file * filp)
+{
+/* More or less stolen from other drivers. */
+ int line;
+ int retval;
+ struct a2232_port *port;
+
+ line = MINOR(tty->device);
+ port = &a2232_ports[line];
+
+ tty->driver_data = port;
+ port->gs.tty = tty;
+ port->gs.count++;
+ retval = gs_init_port(&port->gs);
+ if (retval) {
+ port->gs.count--;
+ return retval;
+ }
+ port->gs.flags |= GS_ACTIVE;
+ if (port->gs.count == 1) {
+ MOD_INC_USE_COUNT;
+ }
+ retval = gs_block_til_ready(port, filp);
+
+ if (retval) {
+ MOD_DEC_USE_COUNT;
+ port->gs.count--;
+ return retval;
+ }
+
+ if ((port->gs.count == 1) && (port->gs.flags & ASYNC_SPLIT_TERMIOS)){
+ if (tty->driver.subtype == A2232_TTY_SUBTYPE_NORMAL)
+ *tty->termios = port->gs.normal_termios;
+ else
+ *tty->termios = port->gs.callout_termios;
+ a2232_set_real_termios (port);
+ }
+
+ port->gs.session = current->session;
+ port->gs.pgrp = current->pgrp;
+
+ a2232_enable_rx_interrupts(port);
+
+ return 0;
+}
+/*** END OF FUNCTIONS EXPECTED BY TTY DRIVER STRUCTS ***/
+
+static __inline__ volatile struct a2232status *a2232stat(unsigned int board, unsigned int portonboard)
+{
+ volatile struct a2232memory *mem = a2232mem(board);
+ return &(mem->Status[portonboard]);
+}
+
+static __inline__ volatile struct a2232memory *a2232mem (unsigned int board)
+{
+ return (volatile struct a2232memory *) ZTWO_VADDR( zd_a2232[board]->resource.start );
+}
+
+static __inline__ void a2232_receive_char( struct a2232_port *port,
+ int ch, int err )
+{
+/* Mostly stolen from other drivers.
+ Maybe one could implement a more efficient version by not only
+ transferring one character at a time.
+*/
+ struct tty_struct *tty = port->gs.tty;
+
+ if (tty->flip.count >= TTY_FLIPBUF_SIZE)
+ return;
+
+ tty->flip.count++;
+
+#if 0
+ switch(err) {
+ case TTY_BREAK:
+ break;
+ case TTY_PARITY:
+ break;
+ case TTY_OVERRUN:
+ break;
+ case TTY_FRAME:
+ break;
+ }
+#endif
+
+ *tty->flip.flag_buf_ptr++ = err;
+ *tty->flip.char_buf_ptr++ = ch;
+ tty_flip_buffer_push(tty);
+}
+
+static void a2232_vbl_inter(int irq, void *data, struct pt_regs *fp)
+{
+#if A2232_IOBUFLEN != 256
+#error "Re-Implement a2232_vbl_inter()!"
+#endif
+
+struct a2232_port *port;
+volatile struct a2232memory *mem;
+volatile struct a2232status *status;
+unsigned char newhead;
+unsigned char bufpos; /* Must be unsigned char. We need the modulo-256 arithmetics */
+unsigned char ncd, ocd, ccd; /* names consistent with the NetBSD driver */
+volatile u_char *ibuf, *cbuf, *obuf;
+int ch, err, n, p;
+ for (n = 0; n < nr_a2232; n++){ /* for every completely initialized A2232 board */
+ mem = a2232mem(n);
+ for (p = 0; p < NUMLINES; p++){ /* for every port on this board */
+ err = 0;
+ port = &a2232_ports[n*NUMLINES+p];
+ if ( port->gs.flags & GS_ACTIVE ){ /* if the port is used */
+
+ status = a2232stat(n,p);
+
+ if (!port->disable_rx && !port->throttle_input){ /* If input is not disabled */
+ newhead = status->InHead; /* 65EC02 write pointer */
+ bufpos = status->InTail;
+
+ /* check for input for this port */
+ if (newhead != bufpos) {
+ /* buffer for input chars/events */
+ ibuf = mem->InBuf[p];
+
+ /* data types of bytes in ibuf */
+ cbuf = mem->InCtl[p];
+
+ /* do for all chars */
+ while (bufpos != newhead) {
+ /* which type of input data? */
+ switch (cbuf[bufpos]) {
+ /* switch on input event (CD, BREAK, etc.) */
+ case A2232INCTL_EVENT:
+ switch (ibuf[bufpos++]) {
+ case A2232EVENT_Break:
+ /* TODO: Handle BREAK signal */
+ break;
+ /* A2232EVENT_CarrierOn and A2232EVENT_CarrierOff are
+ handled in a separate queue and should not occur here. */
+ case A2232EVENT_Sync:
+ printk("A2232: 65EC02 software sent SYNC event, don't know what to do. Ignoring.");
+ break;
+ default:
+ printk("A2232: 65EC02 software broken, unknown event type %d occured.\n",ibuf[bufpos-1]);
+ } /* event type switch */
+ break;
+ case A2232INCTL_CHAR:
+ /* Receive incoming char */
+ a2232_receive_char(port, ibuf[bufpos], err);
+ bufpos++;
+ break;
+ default:
+ printk("A2232: 65EC02 software broken, unknown data type %d occured.\n",cbuf[bufpos]);
+ bufpos++;
+ } /* switch on input data type */
+ } /* while there's something in the buffer */
+
+ status->InTail = bufpos; /* tell 65EC02 what we've read */
+
+ } /* if there was something in the buffer */
+ } /* If input is not disabled */
+
+ /* Now check if there's something to output */
+ obuf = mem->OutBuf[p];
+ bufpos = status->OutHead;
+ while ( (port->gs.xmit_cnt > 0) &&
+ (!port->gs.tty->stopped) &&
+ (!port->gs.tty->hw_stopped) ){ /* While there are chars to transmit */
+ if (((bufpos+1) & A2232_IOBUFLENMASK) != status->OutTail) { /* If the A2232 buffer is not full */
+ ch = port->gs.xmit_buf[port->gs.xmit_tail]; /* get the next char to transmit */
+ port->gs.xmit_tail = (port->gs.xmit_tail+1) & (SERIAL_XMIT_SIZE-1); /* modulo-addition for the gs.xmit_buf ring-buffer */
+ obuf[bufpos++] = ch; /* put it into the A2232 buffer */
+ port->gs.xmit_cnt--;
+ }
+ else{ /* If A2232 the buffer is full */
+ break; /* simply stop filling it. */
+ }
+ }
+ status->OutHead = bufpos;
+
+ /* WakeUp if output buffer runs low */
+ if ((port->gs.xmit_cnt <= port->gs.wakeup_chars) && port->gs.tty) {
+ if ((port->gs.tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && port->gs.tty->ldisc.write_wakeup){
+ (port->gs.tty->ldisc.write_wakeup)(port->gs.tty);
+ }
+ wake_up_interruptible(&port->gs.tty->write_wait);
+ }
+ } // if the port is used
+ } // for every port on the board
+
+ /* Now check the CD message queue */
+ newhead = mem->Common.CDHead;
+ bufpos = mem->Common.CDTail;
+ if (newhead != bufpos){ /* There are CD events in queue */
+ ocd = mem->Common.CDStatus; /* get old status bits */
+ while (newhead != bufpos){ /* read all events */
+ ncd = mem->CDBuf[bufpos++]; /* get one event */
+ ccd = ncd ^ ocd; /* mask of changed lines */
+ ocd = ncd; /* save new status bits */
+ for(p=0; p < NUMLINES; p++){ /* for all ports */
+ if (ccd & 1){ /* this one changed */
+
+ struct a2232_port *port = &a2232_ports[n*7+p];
+ port->cd_status = !(ncd & 1); /* ncd&1 <=> CD is now off */
+
+ if (!(port->gs.flags & ASYNC_CHECK_CD))
+ ; /* Don't report DCD changes */
+ else if (port->cd_status) { // if DCD on: DCD went UP!
+ if (~(port->gs.flags & ASYNC_NORMAL_ACTIVE) ||
+ ~(port->gs.flags & ASYNC_CALLOUT_ACTIVE)) {
+ /* Are we blocking in open?*/
+ wake_up_interruptible(&port->gs.open_wait);
+ }
+ }
+ else { // if DCD off: DCD went DOWN!
+ if (!((port->gs.flags & ASYNC_CALLOUT_ACTIVE) &&
+ (port->gs.flags & ASYNC_CALLOUT_NOHUP))) {
+ if (port->gs.tty)
+ tty_hangup (port->gs.tty);
+ }
+ }
+
+ } // if CD changed for this port
+ ccd >>= 1;
+ ncd >>= 1; /* Shift bits for next line */
+ } // for every port
+ } // while CD events in queue
+ mem->Common.CDStatus = ocd; /* save new status */
+ mem->Common.CDTail = bufpos; /* remove events */
+ } // if events in CD queue
+
+ } // for every completely initialized A2232 board
+}
+
+static void a2232_init_portstructs(void)
+{
+ struct a2232_port *port;
+ int i;
+
+ for (i = 0; i < MAX_A2232_BOARDS*NUMLINES; i++) {
+ port = a2232_ports + i;
+ port->which_a2232 = i/NUMLINES;
+ port->which_port_on_a2232 = i%NUMLINES;
+ port->disable_rx = port->throttle_input = port->cd_status = 0;
+ port->gs.callout_termios = tty_std_termios;
+ port->gs.normal_termios = tty_std_termios;
+ port->gs.magic = A2232_MAGIC;
+ port->gs.close_delay = HZ/2;
+ port->gs.closing_wait = 30 * HZ;
+ port->gs.rd = &a2232_real_driver;
+#ifdef NEW_WRITE_LOCKING
+ init_MUTEX(&(port->gs.port_write_sem));
+#endif
+ init_waitqueue_head(&port->gs.open_wait);
+ init_waitqueue_head(&port->gs.close_wait);
+ }
+}
+
+static int a2232_init_drivers(void)
+{
+ int error;
+
+ memset(&a2232_driver, 0, sizeof(a2232_driver));
+ a2232_driver.magic = TTY_DRIVER_MAGIC;
+ a2232_driver.driver_name = "commodore_a2232";
+ a2232_driver.name = "ttyY";
+ a2232_driver.major = A2232_NORMAL_MAJOR;
+ a2232_driver.num = NUMLINES * nr_a2232;
+ a2232_driver.type = TTY_DRIVER_TYPE_SERIAL;
+ a2232_driver.subtype = A2232_TTY_SUBTYPE_NORMAL;
+ a2232_driver.init_termios = tty_std_termios;
+ a2232_driver.init_termios.c_cflag =
+ B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+ a2232_driver.flags = TTY_DRIVER_REAL_RAW;
+ a2232_driver.refcount = &a2232_refcount;
+ a2232_driver.table = a2232_table;
+ a2232_driver.termios = a2232_termios;
+ a2232_driver.termios_locked = a2232_termios_locked;
+
+ a2232_driver.open = a2232_open;
+ a2232_driver.close = gs_close;
+ a2232_driver.write = gs_write;
+ a2232_driver.put_char = gs_put_char;
+ a2232_driver.flush_chars = gs_flush_chars;
+ a2232_driver.write_room = gs_write_room;
+ a2232_driver.chars_in_buffer = gs_chars_in_buffer;
+ a2232_driver.flush_buffer = gs_flush_buffer;
+ a2232_driver.ioctl = a2232_ioctl;
+ a2232_driver.throttle = a2232_throttle;
+ a2232_driver.unthrottle = a2232_unthrottle;
+ a2232_driver.set_termios = gs_set_termios;
+ a2232_driver.stop = gs_stop;
+ a2232_driver.start = gs_start;
+ a2232_driver.hangup = gs_hangup;
+
+ a2232_callout_driver = a2232_driver;
+ a2232_callout_driver.name = "cuy";
+ a2232_callout_driver.major = A2232_CALLOUT_MAJOR;
+ a2232_callout_driver.subtype = A2232_TTY_SUBTYPE_CALLOUT;
+
+ if ((error = tty_register_driver(&a2232_driver))) {
+ printk(KERN_ERR "A2232: Couldn't register A2232 driver, error = %d\n",
+ error);
+ return 1;
+ }
+ if ((error = tty_register_driver(&a2232_callout_driver))) {
+ tty_unregister_driver(&a2232_driver);
+ printk(KERN_ERR "A2232: Couldn't register A2232 callout driver, error = %d\n",
+ error);
+ return 1;
+ }
+ return 0;
+}
+
+int a2232board_init(void)
+{
+ struct zorro_dev *z;
+
+ unsigned int boardaddr;
+ int bcount;
+ short start;
+ u_char *from;
+ volatile u_char *to;
+ volatile struct a2232memory *mem;
+
+#ifdef __SMP__
+ return -ENODEV; /* This driver is not SMP aware. Is there an SMP ZorroII-bus-machine? */
+#endif
+
+ if (!MACH_IS_AMIGA){
+ return -ENODEV;
+ }
+
+ printk("Commodore A2232 driver initializing.\n"); /* Say that we're alive. */
+
+ z = NULL;
+ nr_a2232 = 0;
+ while ( (z = zorro_find_device(ZORRO_WILDCARD, z)) ){
+ if ( (z->id != ZORRO_PROD_CBM_A2232_PROTOTYPE) &&
+ (z->id != ZORRO_PROD_CBM_A2232) ){
+ continue; // The board found was no A2232
+ }
+ if (!zorro_request_device(z,"A2232 driver"))
+ continue;
+
+ printk("Commodore A2232 found (#%d).\n",nr_a2232);
+
+ zd_a2232[nr_a2232] = z;
+
+ boardaddr = ZTWO_VADDR( z->resource.start );
+ printk("Board is located at address 0x%x, size is 0x%x.\n", boardaddr, (unsigned int) ((z->resource.end+1) - (z->resource.start)));
+
+ mem = (volatile struct a2232memory *) boardaddr;
+
+ (void) mem->Enable6502Reset; /* copy the code across to the board */
+ to = (u_char *)mem; from = a2232_65EC02code; bcount = sizeof(a2232_65EC02code) - 2;
+ start = *(short *)from;
+ from += sizeof(start);
+ to += start;
+ while(bcount--) *to++ = *from++;
+ printk("65EC02 software uploaded to the A2232 memory.\n");
+
+ mem->Common.Crystal = A2232_UNKNOWN; /* use automatic speed check */
+
+ /* start 6502 running */
+ (void) mem->ResetBoard;
+ printk("A2232's 65EC02 CPU up and running.\n");
+
+ /* wait until speed detector has finished */
+ for (bcount = 0; bcount < 2000; bcount++) {
+ udelay(1000);
+ if (mem->Common.Crystal)
+ break;
+ }
+ printk((mem->Common.Crystal?"A2232 oscillator crystal detected by 65EC02 software: ":"65EC02 software could not determine A2232 oscillator crystal: "));
+ switch (mem->Common.Crystal){
+ case A2232_UNKNOWN:
+ printk("Unknown crystal.\n");
+ break;
+ case A2232_NORMAL:
+ printk ("Normal crystal.\n");
+ break;
+ case A2232_TURBO:
+ printk ("Turbo crystal.\n");
+ break;
+ default:
+ printk ("0x%x. Huh?\n",mem->Common.Crystal);
+ }
+
+ nr_a2232++;
+
+ }
+
+ printk("Total: %d A2232 boards initialized.\n.", nr_a2232); /* Some status report if no card was found */
+
+ a2232_init_portstructs();
+
+ /*
+ a2232_init_drivers also registers the drivers. Must be here because all boards
+ have to be detected first.
+ */
+ if (a2232_init_drivers()) return -ENODEV; // maybe we should use a different -Exxx?
+
+ request_irq(IRQ_AMIGA_VERTB, a2232_vbl_inter, 0, "A2232 serial VBL", a2232_driver_ID);
+ return 0;
+}
+
+#ifdef MODULE
+int init_module(void)
+{
+ return a2232board_init();
+}
+
+void cleanup_module(void)
+{
+ int i;
+
+ for (i = 0; i < nr_a2232; i++) {
+ zorro_release_device(zd_a2232[i]);
+ }
+
+ tty_unregister_driver(&a2232_driver);
+ tty_unregister_driver(&a2232_callout_driver);
+ free_irq(IRQ_AMIGA_VERTB, a2232_driver_ID);
+}
+#endif
+/***************************** End of Functions *********************/
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232.h linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232.h
--- linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232.h Thu Jan 1 01:00:00 1970
+++ linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232.h Tue Jul 3 02:36:03 2001
@@ -0,0 +1,206 @@
+/* drivers/char/ser_a2232.h */
+
+/* $Id: ser_a2232.h,v 0.4 2000/01/25 12:00:00 ehaase Exp $ */
+
+/* Linux serial driver for the Amiga A2232 board */
+
+/* This driver is MAINTAINED. Before applying any changes, please contact
+ * the author.
+ */
+
+/* Copyright (c) 2000-2001 Enver Haase <ehaase@inf.fu-berlin.de>
+ * alias The A2232 driver project <A2232@gmx.net>
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef _SER_A2232_H_
+#define _SER_A2232_H_
+
+/*
+ How many boards are to be supported at maximum;
+ "up to five A2232 Multiport Serial Cards may be installed in a
+ single Amiga 2000" states the A2232 User's Guide. If you have
+ more slots available, you might want to change the value below.
+*/
+#define MAX_A2232_BOARDS 5
+
+#ifndef A2232_NORMAL_MAJOR
+/* This allows overriding on the compiler commandline, or in a "major.h"
+ include or something like that */
+#define A2232_NORMAL_MAJOR 224 /* /dev/ttyY* */
+#define A2232_CALLOUT_MAJOR 225 /* /dev/cuy* */
+#endif
+
+/* Some magic is always good - Who knows :) */
+#define A2232_MAGIC 0x000a2232
+
+/* for the tty_struct subtype field */
+#define A2232_TTY_SUBTYPE_NORMAL 1
+#define A2232_TTY_SUBTYPE_CALLOUT 2
+
+/* A2232 port structure to keep track of the
+ status of every single line used */
+struct a2232_port{
+ struct gs_port gs;
+ unsigned int which_a2232;
+ unsigned int which_port_on_a2232;
+ short disable_rx;
+ short throttle_input;
+ short cd_status;
+};
+
+#define NUMLINES 7 /* number of lines per board */
+#define A2232_IOBUFLEN 256 /* number of bytes per buffer */
+#define A2232_IOBUFLENMASK 0xff /* mask for maximum number of bytes */
+
+
+#define A2232_UNKNOWN 0 /* crystal not known */
+#define A2232_NORMAL 1 /* normal A2232 (1.8432 MHz oscillator) */
+#define A2232_TURBO 2 /* turbo A2232 (3.6864 MHz oscillator) */
+
+
+struct a2232common {
+ char Crystal; /* normal (1) or turbo (2) board? */
+ u_char Pad_a;
+ u_char TimerH; /* timer value after speed check */
+ u_char TimerL;
+ u_char CDHead; /* head pointer for CD message queue */
+ u_char CDTail; /* tail pointer for CD message queue */
+ u_char CDStatus;
+ u_char Pad_b;
+};
+
+struct a2232status {
+ u_char InHead; /* input queue head */
+ u_char InTail; /* input queue tail */
+ u_char OutDisable; /* disables output */
+ u_char OutHead; /* output queue head */
+ u_char OutTail; /* output queue tail */
+ u_char OutCtrl; /* soft flow control character to send */
+ u_char OutFlush; /* flushes output buffer */
+ u_char Setup; /* causes reconfiguration */
+ u_char Param; /* parameter byte - see A2232PARAM */
+ u_char Command; /* command byte - see A2232CMD */
+ u_char SoftFlow; /* enables xon/xoff flow control */
+ /* private 65EC02 fields: */
+ u_char XonOff; /* stores XON/XOFF enable/disable */
+};
+
+#define A2232_MEMPAD1 \
+ (0x0200 - NUMLINES * sizeof(struct a2232status) - \
+ sizeof(struct a2232common))
+#define A2232_MEMPAD2 (0x2000 - NUMLINES * A2232_IOBUFLEN - A2232_IOBUFLEN)
+
+struct a2232memory {
+ struct a2232status Status[NUMLINES]; /* 0x0000-0x006f status areas */
+ struct a2232common Common; /* 0x0070-0x0077 common flags */
+ u_char Dummy1[A2232_MEMPAD1]; /* 0x00XX-0x01ff */
+ u_char OutBuf[NUMLINES][A2232_IOBUFLEN];/* 0x0200-0x08ff output bufs */
+ u_char InBuf[NUMLINES][A2232_IOBUFLEN]; /* 0x0900-0x0fff input bufs */
+ u_char InCtl[NUMLINES][A2232_IOBUFLEN]; /* 0x1000-0x16ff control data */
+ u_char CDBuf[A2232_IOBUFLEN]; /* 0x1700-0x17ff CD event buffer */
+ u_char Dummy2[A2232_MEMPAD2]; /* 0x1800-0x2fff */
+ u_char Code[0x1000]; /* 0x3000-0x3fff code area */
+ u_short InterruptAck; /* 0x4000 intr ack */
+ u_char Dummy3[0x3ffe]; /* 0x4002-0x7fff */
+ u_short Enable6502Reset; /* 0x8000 Stop board, */
+ /* 6502 RESET line held low */
+ u_char Dummy4[0x3ffe]; /* 0x8002-0xbfff */
+ u_short ResetBoard; /* 0xc000 reset board & run, */
+ /* 6502 RESET line held high */
+};
+
+#undef A2232_MEMPAD1
+#undef A2232_MEMPAD2
+
+#define A2232INCTL_CHAR 0 /* corresponding byte in InBuf is a character */
+#define A2232INCTL_EVENT 1 /* corresponding byte in InBuf is an event */
+
+#define A2232EVENT_Break 1 /* break set */
+#define A2232EVENT_CarrierOn 2 /* carrier raised */
+#define A2232EVENT_CarrierOff 3 /* carrier dropped */
+#define A2232EVENT_Sync 4 /* don't know, defined in 2232.ax */
+
+#define A2232CMD_Enable 0x1 /* enable/DTR bit */
+#define A2232CMD_Close 0x2 /* close the device */
+#define A2232CMD_Open 0xb /* open the device */
+#define A2232CMD_CMask 0xf /* command mask */
+#define A2232CMD_RTSOff 0x0 /* turn off RTS */
+#define A2232CMD_RTSOn 0x8 /* turn on RTS */
+#define A2232CMD_Break 0xd /* transmit a break */
+#define A2232CMD_RTSMask 0xc /* mask for RTS stuff */
+#define A2232CMD_NoParity 0x00 /* don't use parity */
+#define A2232CMD_OddParity 0x20 /* odd parity */
+#define A2232CMD_EvenParity 0x60 /* even parity */
+#define A2232CMD_ParityMask 0xe0 /* parity mask */
+
+#define A2232PARAM_B115200 0x0 /* baud rates */
+#define A2232PARAM_B50 0x1
+#define A2232PARAM_B75 0x2
+#define A2232PARAM_B110 0x3
+#define A2232PARAM_B134 0x4
+#define A2232PARAM_B150 0x5
+#define A2232PARAM_B300 0x6
+#define A2232PARAM_B600 0x7
+#define A2232PARAM_B1200 0x8
+#define A2232PARAM_B1800 0x9
+#define A2232PARAM_B2400 0xa
+#define A2232PARAM_B3600 0xb
+#define A2232PARAM_B4800 0xc
+#define A2232PARAM_B7200 0xd
+#define A2232PARAM_B9600 0xe
+#define A2232PARAM_B19200 0xf
+#define A2232PARAM_BaudMask 0xf /* baud rate mask */
+#define A2232PARAM_RcvBaud 0x10 /* enable receive baud rate */
+#define A2232PARAM_8Bit 0x00 /* numbers of bits */
+#define A2232PARAM_7Bit 0x20
+#define A2232PARAM_6Bit 0x40
+#define A2232PARAM_5Bit 0x60
+#define A2232PARAM_BitMask 0x60 /* numbers of bits mask */
+
+
+/* Standard speeds tables, -1 means unavailable, -2 means 0 baud: switch off line */
+#define A2232_BAUD_TABLE_NOAVAIL -1
+#define A2232_BAUD_TABLE_NUM_RATES (18)
+static int a2232_baud_table[A2232_BAUD_TABLE_NUM_RATES*3] = {
+ //Baud //Normal //Turbo
+ 50, A2232PARAM_B50, A2232_BAUD_TABLE_NOAVAIL,
+ 75, A2232PARAM_B75, A2232_BAUD_TABLE_NOAVAIL,
+ 110, A2232PARAM_B110, A2232_BAUD_TABLE_NOAVAIL,
+ 134, A2232PARAM_B134, A2232_BAUD_TABLE_NOAVAIL,
+ 150, A2232PARAM_B150, A2232PARAM_B75,
+ 200, A2232_BAUD_TABLE_NOAVAIL, A2232_BAUD_TABLE_NOAVAIL,
+ 300, A2232PARAM_B300, A2232PARAM_B150,
+ 600, A2232PARAM_B600, A2232PARAM_B300,
+ 1200, A2232PARAM_B1200, A2232PARAM_B600,
+ 1800, A2232PARAM_B1800, A2232_BAUD_TABLE_NOAVAIL,
+ 2400, A2232PARAM_B2400, A2232PARAM_B1200,
+ 4800, A2232PARAM_B4800, A2232PARAM_B2400,
+ 9600, A2232PARAM_B9600, A2232PARAM_B4800,
+ 19200, A2232PARAM_B19200, A2232PARAM_B9600,
+ 38400, A2232_BAUD_TABLE_NOAVAIL, A2232PARAM_B19200,
+ 57600, A2232_BAUD_TABLE_NOAVAIL, A2232_BAUD_TABLE_NOAVAIL,
+#ifdef A2232_SPEEDHACK
+ 115200, A2232PARAM_B115200, A2232_BAUD_TABLE_NOAVAIL,
+ 230400, A2232_BAUD_TABLE_NOAVAIL, A2232PARAM_B115200
+#else
+ 115200, A2232_BAUD_TABLE_NOAVAIL, A2232_BAUD_TABLE_NOAVAIL,
+ 230400, A2232_BAUD_TABLE_NOAVAIL, A2232_BAUD_TABLE_NOAVAIL
+#endif
+};
+#endif
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232fw.ax linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232fw.ax
--- linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232fw.ax Thu Jan 1 01:00:00 1970
+++ linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232fw.ax Tue Jul 3 02:36:03 2001
@@ -0,0 +1,529 @@
+;.lib "axm"
+;
+;begin
+;title "A2232 serial board driver"
+;
+;set modules "2232"
+;set executable "2232.bin"
+;
+;;;;set nolink
+;
+;set temporary directory "t:"
+;
+;set assembly options "-m6502 -l60:t:list"
+;set link options "bin"; loadadr"
+;;;bin2c 2232.bin msc6502.h msc6502code
+;end
+;
+;
+; ### Commodore A2232 serial board driver for NetBSD by JM v1.3 ###
+;
+; - Created 950501 by JM -
+;
+;
+; Serial board driver software.
+;
+;
+% Copyright (c) 1995 Jukka Marin <jmarin@jmp.fi>.
+% All rights reserved.
+%
+% Redistribution and use in source and binary forms, with or without
+% modification, are permitted provided that the following conditions
+% are met:
+% 1. Redistributions of source code must retain the above copyright
+% notice, and the entire permission notice in its entirety,
+% including the disclaimer of warranties.
+% 2. Redistributions in binary form must reproduce the above copyright
+% notice, this list of conditions and the following disclaimer in the
+% documentation and/or other materials provided with the distribution.
+% 3. The name of the author may not be used to endorse or promote
+% products derived from this software without specific prior
+% written permission.
+%
+% ALTERNATIVELY, this product may be distributed under the terms of
+% the GNU General Public License, in which case the provisions of the
+% GPL are required INSTEAD OF the above restrictions. (This clause is
+% necessary due to a potential bad interaction between the GPL and
+% the restrictions contained in a BSD-style copyright.)
+%
+% THIS SOFTWARE IS PROVIDED `AS IS'' AND ANY EXPRESS OR IMPLIED
+% WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
+% OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+% DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
+% INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+% (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+% SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+% HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+% STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+% ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+% OF THE POSSIBILITY OF SUCH DAMAGE.
+;
+;
+; Bugs:
+;
+; - Can't send a break yet
+;
+;
+;
+; Edited:
+;
+; - 950501 by JM -> v0.1 - Created this file.
+; - 951029 by JM -> v1.3 - Carrier Detect events now queued in a separate
+; queue.
+;
+;
+
+
+CODE equ $3800 ; start address for program code
+
+
+CTL_CHAR equ $00 ; byte in ibuf is a character
+CTL_EVENT equ $01 ; byte in ibuf is an event
+
+EVENT_BREAK equ $01
+EVENT_CDON equ $02
+EVENT_CDOFF equ $03
+EVENT_SYNC equ $04
+
+XON equ $11
+XOFF equ $13
+
+
+VARBASE macro *starting_address ; was VARINIT
+_varbase set \1
+ endm
+
+VARDEF macro *name space_needs
+\1 equ _varbase
+_varbase set _varbase+\2
+ endm
+
+
+stz macro * address
+ db $64,\1
+ endm
+
+stzax macro * address
+ db $9e,<\1,>\1
+ endm
+
+
+biti macro * immediate value
+ db $89,\1
+ endm
+
+smb0 macro * address
+ db $87,\1
+ endm
+smb1 macro * address
+ db $97,\1
+ endm
+smb2 macro * address
+ db $a7,\1
+ endm
+smb3 macro * address
+ db $b7,\1
+ endm
+smb4 macro * address
+ db $c7,\1
+ endm
+smb5 macro * address
+ db $d7,\1
+ endm
+smb6 macro * address
+ db $e7,\1
+ endm
+smb7 macro * address
+ db $f7,\1
+ endm
+
+
+
+;-----------------------------------------------------------------------;
+; ;
+; stuff common for all ports, non-critical (run once / loop) ;
+; ;
+DO_SLOW macro * port_number ;
+ .local ; ;
+ lda CIA+C_PA ; check all CD inputs ;
+ cmp CommonCDo ; changed from previous accptd? ;
+ beq =over ; nope, do nothing else here ;
+ ; ;
+ cmp CommonCDb ; bouncing? ;
+ beq =nobounce ; nope -> ;
+ ; ;
+ sta CommonCDb ; save current state ;
+ lda #64 ; reinitialize counter ;
+ sta CommonCDc ; ;
+ jmp =over ; skip CD save ;
+ ; ;
+=nobounce dec CommonCDc ; no, decrement bounce counter ;
+ bpl =over ; not done yet, so skip CD save ;
+ ; ;
+=saveCD ldx CDHead ; get write index ;
+ sta cdbuf,x ; save status in buffer ;
+ inx ; ;
+ cpx CDTail ; buffer full? ;
+ .if ne ; no: preserve status: ;
+ stx CDHead ; update index in RAM ;
+ sta CommonCDo ; save state for the next check ;
+ .end ; ;
+=over .end local ;
+ endm ;
+ ;
+;-----------------------------------------------------------------------;
+
+
+; port specific stuff (no data transfer)
+
+DO_PORT macro * port_number
+ .local ; ;
+ lda SetUp\1 ; reconfiguration request? ;
+ .if ne ; yes: ;
+ lda SoftFlow\1 ; get XON/XOFF flag ;
+ sta XonOff\1 ; save it ;
+ lda Param\1 ; get parameter ;
+ ora #%00010000 ; use baud generator for Rx ;
+ sta ACIA\1+A_CTRL ; store in control register ;
+ stz OutDisable\1 ; enable transmit output ;
+ stz SetUp\1 ; no reconfiguration no more ;
+ .end ; ;
+ ; ;
+ lda InHead\1 ; get write index ;
+ sbc InTail\1 ; buffer full soon? ;
+ cmp #200 ; 200 chars or more in buffer? ;
+ lda Command\1 ; get Command reg value ;
+ and #%11110011 ; turn RTS OFF by default ;
+ .if cc ; still room in buffer: ;
+ ora #%00001000 ; turn RTS ON ;
+ .end ; ;
+ sta ACIA\1+A_CMD ; set/clear RTS ;
+ ; ;
+ lda OutFlush\1 ; request to flush output buffer;
+ .if ne ; yessh! ;
+ lda OutHead\1 ; get head ;
+ sta OutTail\1 ; save as tail ;
+ stz OutDisable\1 ; enable transmit output ;
+ stz OutFlush\1 ; clear request ;
+ .end
+ .end local
+ endm
+
+
+DO_DATA macro * port number
+ .local
+ lda ACIA\1+A_SR ; read ACIA status register ;
+ biti [1<<3] ; something received? ;
+ .if ne ; yes: ;
+ biti [1<<1] ; framing error? ;
+ .if ne ; yes: ;
+ lda ACIA\1+A_DATA ; read received character ;
+ bne =SEND ; not break -> ignore it ;
+ ldx InHead\1 ; get write pointer ;
+ lda #CTL_EVENT ; get type of byte ;
+ sta ictl\1,x ; save it in InCtl buffer ;
+ lda #EVENT_BREAK ; event code ;
+ sta ibuf\1,x ; save it as well ;
+ inx ; ;
+ cpx InTail\1 ; still room in buffer? ;
+ .if ne ; absolutely: ;
+ stx InHead\1 ; update index in memory ;
+ .end ; ;
+ jmp =SEND ; go check if anything to send ;
+ .end ; ;
+ ; normal char received: ;
+ ldx InHead\1 ; get write index ;
+ lda ACIA\1+A_DATA ; read received character ;
+ sta ibuf\1,x ; save char in buffer ;
+ stzax ictl\1 ; set type to CTL_CHAR ;
+ inx ; ;
+ cpx InTail\1 ; buffer full? ;
+ .if ne ; no: preserve character: ;
+ stx InHead\1 ; update index in RAM ;
+ .end ; ;
+ and #$7f ; mask off parity if any ;
+ cmp #XOFF ; XOFF from remote host? ;
+ .if eq ; yes: ;
+ lda XonOff\1 ; if XON/XOFF handshaking.. ;
+ sta OutDisable\1 ; ..disable transmitter ;
+ .end ; ;
+ .end ; ;
+ ; ;
+ ; BUFFER FULL CHECK WAS HERE ;
+ ; ;
+=SEND lda ACIA\1+A_SR ; transmit register empty? ;
+ and #[1<<4] ; ;
+ .if ne ; yes: ;
+ ldx OutCtrl\1 ; sending out XON/XOFF? ;
+ .if ne ; yes: ;
+ lda CIA+C_PB ; check CTS signal ;
+ and #[1<<\1] ; (for this port only) ;
+ bne =DONE ; not allowed to send -> done ;
+ stx ACIA\1+A_DATA ; transmit control char ;
+ stz OutCtrl\1 ; clear flag ;
+ jmp =DONE ; and we're done ;
+ .end ; ;
+ ; ;
+ ldx OutTail\1 ; anything to transmit? ;
+ cpx OutHead\1 ; ;
+ .if ne ; yes: ;
+ lda OutDisable\1 ; allowed to transmit? ;
+ .if eq ; yes: ;
+ lda CIA+C_PB ; check CTS signal ;
+ and #[1<<\1] ; (for this port only) ;
+ bne =DONE ; not allowed to send -> done ;
+ lda obuf\1,x ; get a char from buffer ;
+ sta ACIA\1+A_DATA ; send it away ;
+ inc OutTail\1 ; update read index ;
+ .end ; ;
+ .end ; ;
+ .end ; ;
+=DONE .end local
+ endm
+
+
+
+PORTVAR macro * port number
+ VARDEF InHead\1 1
+ VARDEF InTail\1 1
+ VARDEF OutDisable\1 1
+ VARDEF OutHead\1 1
+ VARDEF OutTail\1 1
+ VARDEF OutCtrl\1 1
+ VARDEF OutFlush\1 1
+ VARDEF SetUp\1 1
+ VARDEF Param\1 1
+ VARDEF Command\1 1
+ VARDEF SoftFlow\1 1
+ ; private:
+ VARDEF XonOff\1 1
+ endm
+
+
+ VARBASE 0 ; start variables at address $0000
+ PORTVAR 0 ; define variables for port 0
+ PORTVAR 1 ; define variables for port 1
+ PORTVAR 2 ; define variables for port 2
+ PORTVAR 3 ; define variables for port 3
+ PORTVAR 4 ; define variables for port 4
+ PORTVAR 5 ; define variables for port 5
+ PORTVAR 6 ; define variables for port 6
+
+
+
+ VARDEF Crystal 1 ; 0 = unknown, 1 = normal, 2 = turbo
+ VARDEF Pad_a 1
+ VARDEF TimerH 1
+ VARDEF TimerL 1
+ VARDEF CDHead 1
+ VARDEF CDTail 1
+ VARDEF CDStatus 1
+ VARDEF Pad_b 1
+
+ VARDEF CommonCDo 1 ; for carrier detect optimization
+ VARDEF CommonCDc 1 ; for carrier detect debouncing
+ VARDEF CommonCDb 1 ; for carrier detect debouncing
+
+
+ VARBASE $0200
+ VARDEF obuf0 256 ; output data (characters only)
+ VARDEF obuf1 256
+ VARDEF obuf2 256
+ VARDEF obuf3 256
+ VARDEF obuf4 256
+ VARDEF obuf5 256
+ VARDEF obuf6 256
+
+ VARDEF ibuf0 256 ; input data (characters, events etc - see ictl)
+ VARDEF ibuf1 256
+ VARDEF ibuf2 256
+ VARDEF ibuf3 256
+ VARDEF ibuf4 256
+ VARDEF ibuf5 256
+ VARDEF ibuf6 256
+
+ VARDEF ictl0 256 ; input control information (type of data in ibuf)
+ VARDEF ictl1 256
+ VARDEF ictl2 256
+ VARDEF ictl3 256
+ VARDEF ictl4 256
+ VARDEF ictl5 256
+ VARDEF ictl6 256
+
+ VARDEF cdbuf 256 ; CD event queue
+
+
+ACIA0 equ $4400
+ACIA1 equ $4c00
+ACIA2 equ $5400
+ACIA3 equ $5c00
+ACIA4 equ $6400
+ACIA5 equ $6c00
+ACIA6 equ $7400
+
+A_DATA equ $00
+A_SR equ $02
+A_CMD equ $04
+A_CTRL equ $06
+; 00 write transmit data read received data
+; 02 reset ACIA read status register
+; 04 write command register read command register
+; 06 write control register read control register
+
+CIA equ $7c00 ; 8520 CIA
+C_PA equ $00 ; port A data register
+C_PB equ $02 ; port B data register
+C_DDRA equ $04 ; data direction register for port A
+C_DDRB equ $06 ; data direction register for port B
+C_TAL equ $08 ; timer A
+C_TAH equ $0a
+C_TBL equ $0c ; timer B
+C_TBH equ $0e
+C_TODL equ $10 ; TOD LSB
+C_TODM equ $12 ; TOD middle byte
+C_TODH equ $14 ; TOD MSB
+C_DATA equ $18 ; serial data register
+C_INTCTRL equ $1a ; interrupt control register
+C_CTRLA equ $1c ; control register A
+C_CTRLB equ $1e ; control register B
+
+
+
+
+
+ section main,code,CODE-2
+
+ db >CODE,<CODE
+
+;-----------------------------------------------------------------------;
+; here's the initialization code: ;
+; ;
+R_RESET ldx #$ff ;
+ txs ; initialize stack pointer ;
+ cld ; in case a 6502 is used... ;
+ ldx #0 ; ;
+ lda #0 ; ;
+ ldy #Crystal ; this many bytes to clear ;
+clr_loop sta 0,x ; clear zero page variables ;
+ inx ; ;
+ dey ; ;
+ bne clr_loop ; ;
+ ; ;
+ stz CommonCDo ; force CD test at boot ;
+ stz CommonCDb ; ;
+ stz CDHead ; clear queue ;
+ stz CDTail ; ;
+ ; ;
+ lda #0 ; ;
+ sta Pad_a ; ;
+ lda #170 ; test cmp ;
+ cmp #100 ; ;
+ .if cs ; ;
+ inc Pad_a ; C was set ;
+ .end ; ;
+ ;
+;-----------------------------------------------------------------------;
+; Speed check ;
+;-----------------------------------------------------------------------;
+ ;
+ lda Crystal ; speed already set? ;
+ beq DoSpeedy ; ;
+ jmp LOOP ; yes, skip speed test ;
+ ; ;
+DoSpeedy lda #%10011000 ; 8N1, 1200/2400 bps ;
+ sta ACIA0+A_CTRL ; ;
+ lda #%00001011 ; enable DTR ;
+ sta ACIA0+A_CMD ; ;
+ lda ACIA0+A_SR ; read status register ;
+ ; ;
+ lda #%10000000 ; disable all ints (unnecessary);
+ sta CIA+C_INTCTRL ; ;
+ lda #255 ; program the timer ;
+ sta CIA+C_TAL ; ;
+ sta CIA+C_TAH ; ;
+ ; ;
+ ldx #0 ; ;
+ stx ACIA0+A_DATA ; transmit a zero ;
+ nop ; ;
+ nop ; ;
+ lda ACIA0+A_SR ; read status ;
+ nop ; ;
+ nop ; ;
+ stx ACIA0+A_DATA ; transmit a zero ;
+Speedy1 lda ACIA0+A_SR ; read status ;
+ and #[1<<4] ; transmit data reg empty? ;
+ beq Speedy1 ; not yet, wait more ;
+ ; ;
+ lda #%00010001 ; load & start the timer ;
+ stx ACIA0+A_DATA ; transmit one more zero ;
+ sta CIA+C_CTRLA ; ;
+Speedy2 lda ACIA0+A_SR ; read status ;
+ and #[1<<4] ; transmit data reg empty? ;
+ beq Speedy2 ; not yet, wait more ;
+ stx CIA+C_CTRLA ; stop the timer ;
+ ; ;
+ lda CIA+C_TAL ; copy timer value for 68k ;
+ sta TimerL ; ;
+ lda CIA+C_TAH ; ;
+ sta TimerH ; ;
+ cmp #$d0 ; turbo or normal? ;
+ .if cs ; ;
+ lda #2 ; turbo! :-) ;
+ .else ; ;
+ lda #1 ; normal :-( ;
+ .end ; ;
+ sta Crystal ; ;
+ lda #0 ; ;
+ sta ACIA0+A_SR ; ;
+ sta ACIA0+A_CTRL ; reset UART ;
+ sta ACIA0+A_CMD ; ;
+ ;
+ jmp LOOP ;
+ ;
+; ;
+;-----------------------------------------------------------------------;
+; ;
+; The Real Thing: ;
+; ;
+LOOP DO_SLOW ; do non-critical things ;
+ jsr do_input ; check for received data
+ DO_PORT 0
+ jsr do_input
+ DO_PORT 1
+ jsr do_input
+ DO_PORT 2
+ jsr do_input
+ DO_PORT 3
+ jsr do_input
+ DO_PORT 4
+ jsr do_input
+ DO_PORT 5
+ jsr do_input
+ DO_PORT 6
+ jsr do_input
+ jmp LOOP
+
+
+do_input DO_DATA 0
+ DO_DATA 1
+ DO_DATA 2
+ DO_DATA 3
+ DO_DATA 4
+ DO_DATA 5
+ DO_DATA 6
+ rts
+
+
+;-----------------------------------------------------------------------;
+ section vectors,data,$3ffa
+ dw $d0d0
+ dw R_RESET
+ dw $c0ce
+;-----------------------------------------------------------------------;
+
+
+
+ end
+
+
+
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232fw.h linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232fw.h
--- linux-2.4.6-pre8-vanilla/drivers/char/ser_a2232fw.h Thu Jan 1 01:00:00 1970
+++ linux-2.4.6-pre8-withA2232/drivers/char/ser_a2232fw.h Tue Jul 3 02:36:03 2001
@@ -0,0 +1,306 @@
+/* drivers/char/ser_a2232fw.h */
+
+/* $Id: ser_a2232fw.h,v 0.4 2000/01/25 12:00:00 ehaase Exp $ */
+
+/*
+ * Copyright (c) 1995 Jukka Marin <jmarin@jmp.fi>.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, and the entire permission notice in its entirety,
+ * including the disclaimer of warranties.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. The name of the author may not be used to endorse or promote
+ * products derived from this software without specific prior
+ * written permission.
+ *
+ * ALTERNATIVELY, this product may be distributed under the terms of
+ * the GNU Public License, in which case the provisions of the GPL are
+ * required INSTEAD OF the above restrictions. (This clause is
+ * necessary due to a potential bad interaction between the GPL and
+ * the restrictions contained in a BSD-style copyright.)
+ *
+ * THIS SOFTWARE IS PROVIDED `AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
+ * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ * OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+
+/* This is the 65EC02 code by Jukka Marin that is executed by
+ the A2232's 65EC02 processor (base address: 0x3800)
+ Source file: ser_a2232fw.ax
+ Version: 1.3 (951029)
+ Known Bugs: Cannot send a break yet
+*/
+static unsigned char a2232_65EC02code[] = {
+ 0x38, 0x00, 0xA2, 0xFF, 0x9A, 0xD8, 0xA2, 0x00,
+ 0xA9, 0x00, 0xA0, 0x54, 0x95, 0x00, 0xE8, 0x88,
+ 0xD0, 0xFA, 0x64, 0x5C, 0x64, 0x5E, 0x64, 0x58,
+ 0x64, 0x59, 0xA9, 0x00, 0x85, 0x55, 0xA9, 0xAA,
+ 0xC9, 0x64, 0x90, 0x02, 0xE6, 0x55, 0xA5, 0x54,
+ 0xF0, 0x03, 0x4C, 0x92, 0x38, 0xA9, 0x98, 0x8D,
+ 0x06, 0x44, 0xA9, 0x0B, 0x8D, 0x04, 0x44, 0xAD,
+ 0x02, 0x44, 0xA9, 0x80, 0x8D, 0x1A, 0x7C, 0xA9,
+ 0xFF, 0x8D, 0x08, 0x7C, 0x8D, 0x0A, 0x7C, 0xA2,
+ 0x00, 0x8E, 0x00, 0x44, 0xEA, 0xEA, 0xAD, 0x02,
+ 0x44, 0xEA, 0xEA, 0x8E, 0x00, 0x44, 0xAD, 0x02,
+ 0x44, 0x29, 0x10, 0xF0, 0xF9, 0xA9, 0x11, 0x8E,
+ 0x00, 0x44, 0x8D, 0x1C, 0x7C, 0xAD, 0x02, 0x44,
+ 0x29, 0x10, 0xF0, 0xF9, 0x8E, 0x1C, 0x7C, 0xAD,
+ 0x08, 0x7C, 0x85, 0x57, 0xAD, 0x0A, 0x7C, 0x85,
+ 0x56, 0xC9, 0xD0, 0x90, 0x05, 0xA9, 0x02, 0x4C,
+ 0x82, 0x38, 0xA9, 0x01, 0x85, 0x54, 0xA9, 0x00,
+ 0x8D, 0x02, 0x44, 0x8D, 0x06, 0x44, 0x8D, 0x04,
+ 0x44, 0x4C, 0x92, 0x38, 0xAD, 0x00, 0x7C, 0xC5,
+ 0x5C, 0xF0, 0x1F, 0xC5, 0x5E, 0xF0, 0x09, 0x85,
+ 0x5E, 0xA9, 0x40, 0x85, 0x5D, 0x4C, 0xB8, 0x38,
+ 0xC6, 0x5D, 0x10, 0x0E, 0xA6, 0x58, 0x9D, 0x00,
+ 0x17, 0xE8, 0xE4, 0x59, 0xF0, 0x04, 0x86, 0x58,
+ 0x85, 0x5C, 0x20, 0x23, 0x3A, 0xA5, 0x07, 0xF0,
+ 0x0F, 0xA5, 0x0A, 0x85, 0x0B, 0xA5, 0x08, 0x09,
+ 0x10, 0x8D, 0x06, 0x44, 0x64, 0x02, 0x64, 0x07,
+ 0xA5, 0x00, 0xE5, 0x01, 0xC9, 0xC8, 0xA5, 0x09,
+ 0x29, 0xF3, 0xB0, 0x02, 0x09, 0x08, 0x8D, 0x04,
+ 0x44, 0xA5, 0x06, 0xF0, 0x08, 0xA5, 0x03, 0x85,
+ 0x04, 0x64, 0x02, 0x64, 0x06, 0x20, 0x23, 0x3A,
+ 0xA5, 0x13, 0xF0, 0x0F, 0xA5, 0x16, 0x85, 0x17,
+ 0xA5, 0x14, 0x09, 0x10, 0x8D, 0x06, 0x4C, 0x64,
+ 0x0E, 0x64, 0x13, 0xA5, 0x0C, 0xE5, 0x0D, 0xC9,
+ 0xC8, 0xA5, 0x15, 0x29, 0xF3, 0xB0, 0x02, 0x09,
+ 0x08, 0x8D, 0x04, 0x4C, 0xA5, 0x12, 0xF0, 0x08,
+ 0xA5, 0x0F, 0x85, 0x10, 0x64, 0x0E, 0x64, 0x12,
+ 0x20, 0x23, 0x3A, 0xA5, 0x1F, 0xF0, 0x0F, 0xA5,
+ 0x22, 0x85, 0x23, 0xA5, 0x20, 0x09, 0x10, 0x8D,
+ 0x06, 0x54, 0x64, 0x1A, 0x64, 0x1F, 0xA5, 0x18,
+ 0xE5, 0x19, 0xC9, 0xC8, 0xA5, 0x21, 0x29, 0xF3,
+ 0xB0, 0x02, 0x09, 0x08, 0x8D, 0x04, 0x54, 0xA5,
+ 0x1E, 0xF0, 0x08, 0xA5, 0x1B, 0x85, 0x1C, 0x64,
+ 0x1A, 0x64, 0x1E, 0x20, 0x23, 0x3A, 0xA5, 0x2B,
+ 0xF0, 0x0F, 0xA5, 0x2E, 0x85, 0x2F, 0xA5, 0x2C,
+ 0x09, 0x10, 0x8D, 0x06, 0x5C, 0x64, 0x26, 0x64,
+ 0x2B, 0xA5, 0x24, 0xE5, 0x25, 0xC9, 0xC8, 0xA5,
+ 0x2D, 0x29, 0xF3, 0xB0, 0x02, 0x09, 0x08, 0x8D,
+ 0x04, 0x5C, 0xA5, 0x2A, 0xF0, 0x08, 0xA5, 0x27,
+ 0x85, 0x28, 0x64, 0x26, 0x64, 0x2A, 0x20, 0x23,
+ 0x3A, 0xA5, 0x37, 0xF0, 0x0F, 0xA5, 0x3A, 0x85,
+ 0x3B, 0xA5, 0x38, 0x09, 0x10, 0x8D, 0x06, 0x64,
+ 0x64, 0x32, 0x64, 0x37, 0xA5, 0x30, 0xE5, 0x31,
+ 0xC9, 0xC8, 0xA5, 0x39, 0x29, 0xF3, 0xB0, 0x02,
+ 0x09, 0x08, 0x8D, 0x04, 0x64, 0xA5, 0x36, 0xF0,
+ 0x08, 0xA5, 0x33, 0x85, 0x34, 0x64, 0x32, 0x64,
+ 0x36, 0x20, 0x23, 0x3A, 0xA5, 0x43, 0xF0, 0x0F,
+ 0xA5, 0x46, 0x85, 0x47, 0xA5, 0x44, 0x09, 0x10,
+ 0x8D, 0x06, 0x6C, 0x64, 0x3E, 0x64, 0x43, 0xA5,
+ 0x3C, 0xE5, 0x3D, 0xC9, 0xC8, 0xA5, 0x45, 0x29,
+ 0xF3, 0xB0, 0x02, 0x09, 0x08, 0x8D, 0x04, 0x6C,
+ 0xA5, 0x42, 0xF0, 0x08, 0xA5, 0x3F, 0x85, 0x40,
+ 0x64, 0x3E, 0x64, 0x42, 0x20, 0x23, 0x3A, 0xA5,
+ 0x4F, 0xF0, 0x0F, 0xA5, 0x52, 0x85, 0x53, 0xA5,
+ 0x50, 0x09, 0x10, 0x8D, 0x06, 0x74, 0x64, 0x4A,
+ 0x64, 0x4F, 0xA5, 0x48, 0xE5, 0x49, 0xC9, 0xC8,
+ 0xA5, 0x51, 0x29, 0xF3, 0xB0, 0x02, 0x09, 0x08,
+ 0x8D, 0x04, 0x74, 0xA5, 0x4E, 0xF0, 0x08, 0xA5,
+ 0x4B, 0x85, 0x4C, 0x64, 0x4A, 0x64, 0x4E, 0x20,
+ 0x23, 0x3A, 0x4C, 0x92, 0x38, 0xAD, 0x02, 0x44,
+ 0x89, 0x08, 0xF0, 0x3B, 0x89, 0x02, 0xF0, 0x1B,
+ 0xAD, 0x00, 0x44, 0xD0, 0x32, 0xA6, 0x00, 0xA9,
+ 0x01, 0x9D, 0x00, 0x10, 0xA9, 0x01, 0x9D, 0x00,
+ 0x09, 0xE8, 0xE4, 0x01, 0xF0, 0x02, 0x86, 0x00,
+ 0x4C, 0x65, 0x3A, 0xA6, 0x00, 0xAD, 0x00, 0x44,
+ 0x9D, 0x00, 0x09, 0x9E, 0x00, 0x10, 0xE8, 0xE4,
+ 0x01, 0xF0, 0x02, 0x86, 0x00, 0x29, 0x7F, 0xC9,
+ 0x13, 0xD0, 0x04, 0xA5, 0x0B, 0x85, 0x02, 0xAD,
+ 0x02, 0x44, 0x29, 0x10, 0xF0, 0x2C, 0xA6, 0x05,
+ 0xF0, 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x01, 0xD0,
+ 0x21, 0x8E, 0x00, 0x44, 0x64, 0x05, 0x4C, 0x98,
+ 0x3A, 0xA6, 0x04, 0xE4, 0x03, 0xF0, 0x13, 0xA5,
+ 0x02, 0xD0, 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x01,
+ 0xD0, 0x08, 0xBD, 0x00, 0x02, 0x8D, 0x00, 0x44,
+ 0xE6, 0x04, 0xAD, 0x02, 0x4C, 0x89, 0x08, 0xF0,
+ 0x3B, 0x89, 0x02, 0xF0, 0x1B, 0xAD, 0x00, 0x4C,
+ 0xD0, 0x32, 0xA6, 0x0C, 0xA9, 0x01, 0x9D, 0x00,
+ 0x11, 0xA9, 0x01, 0x9D, 0x00, 0x0A, 0xE8, 0xE4,
+ 0x0D, 0xF0, 0x02, 0x86, 0x0C, 0x4C, 0xDA, 0x3A,
+ 0xA6, 0x0C, 0xAD, 0x00, 0x4C, 0x9D, 0x00, 0x0A,
+ 0x9E, 0x00, 0x11, 0xE8, 0xE4, 0x0D, 0xF0, 0x02,
+ 0x86, 0x0C, 0x29, 0x7F, 0xC9, 0x13, 0xD0, 0x04,
+ 0xA5, 0x17, 0x85, 0x0E, 0xAD, 0x02, 0x4C, 0x29,
+ 0x10, 0xF0, 0x2C, 0xA6, 0x11, 0xF0, 0x0F, 0xAD,
+ 0x02, 0x7C, 0x29, 0x02, 0xD0, 0x21, 0x8E, 0x00,
+ 0x4C, 0x64, 0x11, 0x4C, 0x0D, 0x3B, 0xA6, 0x10,
+ 0xE4, 0x0F, 0xF0, 0x13, 0xA5, 0x0E, 0xD0, 0x0F,
+ 0xAD, 0x02, 0x7C, 0x29, 0x02, 0xD0, 0x08, 0xBD,
+ 0x00, 0x03, 0x8D, 0x00, 0x4C, 0xE6, 0x10, 0xAD,
+ 0x02, 0x54, 0x89, 0x08, 0xF0, 0x3B, 0x89, 0x02,
+ 0xF0, 0x1B, 0xAD, 0x00, 0x54, 0xD0, 0x32, 0xA6,
+ 0x18, 0xA9, 0x01, 0x9D, 0x00, 0x12, 0xA9, 0x01,
+ 0x9D, 0x00, 0x0B, 0xE8, 0xE4, 0x19, 0xF0, 0x02,
+ 0x86, 0x18, 0x4C, 0x4F, 0x3B, 0xA6, 0x18, 0xAD,
+ 0x00, 0x54, 0x9D, 0x00, 0x0B, 0x9E, 0x00, 0x12,
+ 0xE8, 0xE4, 0x19, 0xF0, 0x02, 0x86, 0x18, 0x29,
+ 0x7F, 0xC9, 0x13, 0xD0, 0x04, 0xA5, 0x23, 0x85,
+ 0x1A, 0xAD, 0x02, 0x54, 0x29, 0x10, 0xF0, 0x2C,
+ 0xA6, 0x1D, 0xF0, 0x0F, 0xAD, 0x02, 0x7C, 0x29,
+ 0x04, 0xD0, 0x21, 0x8E, 0x00, 0x54, 0x64, 0x1D,
+ 0x4C, 0x82, 0x3B, 0xA6, 0x1C, 0xE4, 0x1B, 0xF0,
+ 0x13, 0xA5, 0x1A, 0xD0, 0x0F, 0xAD, 0x02, 0x7C,
+ 0x29, 0x04, 0xD0, 0x08, 0xBD, 0x00, 0x04, 0x8D,
+ 0x00, 0x54, 0xE6, 0x1C, 0xAD, 0x02, 0x5C, 0x89,
+ 0x08, 0xF0, 0x3B, 0x89, 0x02, 0xF0, 0x1B, 0xAD,
+ 0x00, 0x5C, 0xD0, 0x32, 0xA6, 0x24, 0xA9, 0x01,
+ 0x9D, 0x00, 0x13, 0xA9, 0x01, 0x9D, 0x00, 0x0C,
+ 0xE8, 0xE4, 0x25, 0xF0, 0x02, 0x86, 0x24, 0x4C,
+ 0xC4, 0x3B, 0xA6, 0x24, 0xAD, 0x00, 0x5C, 0x9D,
+ 0x00, 0x0C, 0x9E, 0x00, 0x13, 0xE8, 0xE4, 0x25,
+ 0xF0, 0x02, 0x86, 0x24, 0x29, 0x7F, 0xC9, 0x13,
+ 0xD0, 0x04, 0xA5, 0x2F, 0x85, 0x26, 0xAD, 0x02,
+ 0x5C, 0x29, 0x10, 0xF0, 0x2C, 0xA6, 0x29, 0xF0,
+ 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x08, 0xD0, 0x21,
+ 0x8E, 0x00, 0x5C, 0x64, 0x29, 0x4C, 0xF7, 0x3B,
+ 0xA6, 0x28, 0xE4, 0x27, 0xF0, 0x13, 0xA5, 0x26,
+ 0xD0, 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x08, 0xD0,
+ 0x08, 0xBD, 0x00, 0x05, 0x8D, 0x00, 0x5C, 0xE6,
+ 0x28, 0xAD, 0x02, 0x64, 0x89, 0x08, 0xF0, 0x3B,
+ 0x89, 0x02, 0xF0, 0x1B, 0xAD, 0x00, 0x64, 0xD0,
+ 0x32, 0xA6, 0x30, 0xA9, 0x01, 0x9D, 0x00, 0x14,
+ 0xA9, 0x01, 0x9D, 0x00, 0x0D, 0xE8, 0xE4, 0x31,
+ 0xF0, 0x02, 0x86, 0x30, 0x4C, 0x39, 0x3C, 0xA6,
+ 0x30, 0xAD, 0x00, 0x64, 0x9D, 0x00, 0x0D, 0x9E,
+ 0x00, 0x14, 0xE8, 0xE4, 0x31, 0xF0, 0x02, 0x86,
+ 0x30, 0x29, 0x7F, 0xC9, 0x13, 0xD0, 0x04, 0xA5,
+ 0x3B, 0x85, 0x32, 0xAD, 0x02, 0x64, 0x29, 0x10,
+ 0xF0, 0x2C, 0xA6, 0x35, 0xF0, 0x0F, 0xAD, 0x02,
+ 0x7C, 0x29, 0x10, 0xD0, 0x21, 0x8E, 0x00, 0x64,
+ 0x64, 0x35, 0x4C, 0x6C, 0x3C, 0xA6, 0x34, 0xE4,
+ 0x33, 0xF0, 0x13, 0xA5, 0x32, 0xD0, 0x0F, 0xAD,
+ 0x02, 0x7C, 0x29, 0x10, 0xD0, 0x08, 0xBD, 0x00,
+ 0x06, 0x8D, 0x00, 0x64, 0xE6, 0x34, 0xAD, 0x02,
+ 0x6C, 0x89, 0x08, 0xF0, 0x3B, 0x89, 0x02, 0xF0,
+ 0x1B, 0xAD, 0x00, 0x6C, 0xD0, 0x32, 0xA6, 0x3C,
+ 0xA9, 0x01, 0x9D, 0x00, 0x15, 0xA9, 0x01, 0x9D,
+ 0x00, 0x0E, 0xE8, 0xE4, 0x3D, 0xF0, 0x02, 0x86,
+ 0x3C, 0x4C, 0xAE, 0x3C, 0xA6, 0x3C, 0xAD, 0x00,
+ 0x6C, 0x9D, 0x00, 0x0E, 0x9E, 0x00, 0x15, 0xE8,
+ 0xE4, 0x3D, 0xF0, 0x02, 0x86, 0x3C, 0x29, 0x7F,
+ 0xC9, 0x13, 0xD0, 0x04, 0xA5, 0x47, 0x85, 0x3E,
+ 0xAD, 0x02, 0x6C, 0x29, 0x10, 0xF0, 0x2C, 0xA6,
+ 0x41, 0xF0, 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x20,
+ 0xD0, 0x21, 0x8E, 0x00, 0x6C, 0x64, 0x41, 0x4C,
+ 0xE1, 0x3C, 0xA6, 0x40, 0xE4, 0x3F, 0xF0, 0x13,
+ 0xA5, 0x3E, 0xD0, 0x0F, 0xAD, 0x02, 0x7C, 0x29,
+ 0x20, 0xD0, 0x08, 0xBD, 0x00, 0x07, 0x8D, 0x00,
+ 0x6C, 0xE6, 0x40, 0xAD, 0x02, 0x74, 0x89, 0x08,
+ 0xF0, 0x3B, 0x89, 0x02, 0xF0, 0x1B, 0xAD, 0x00,
+ 0x74, 0xD0, 0x32, 0xA6, 0x48, 0xA9, 0x01, 0x9D,
+ 0x00, 0x16, 0xA9, 0x01, 0x9D, 0x00, 0x0F, 0xE8,
+ 0xE4, 0x49, 0xF0, 0x02, 0x86, 0x48, 0x4C, 0x23,
+ 0x3D, 0xA6, 0x48, 0xAD, 0x00, 0x74, 0x9D, 0x00,
+ 0x0F, 0x9E, 0x00, 0x16, 0xE8, 0xE4, 0x49, 0xF0,
+ 0x02, 0x86, 0x48, 0x29, 0x7F, 0xC9, 0x13, 0xD0,
+ 0x04, 0xA5, 0x53, 0x85, 0x4A, 0xAD, 0x02, 0x74,
+ 0x29, 0x10, 0xF0, 0x2C, 0xA6, 0x4D, 0xF0, 0x0F,
+ 0xAD, 0x02, 0x7C, 0x29, 0x40, 0xD0, 0x21, 0x8E,
+ 0x00, 0x74, 0x64, 0x4D, 0x4C, 0x56, 0x3D, 0xA6,
+ 0x4C, 0xE4, 0x4B, 0xF0, 0x13, 0xA5, 0x4A, 0xD0,
+ 0x0F, 0xAD, 0x02, 0x7C, 0x29, 0x40, 0xD0, 0x08,
+ 0xBD, 0x00, 0x08, 0x8D, 0x00, 0x74, 0xE6, 0x4C,
+ 0x60, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xFF, 0xD0, 0xD0, 0x00, 0x38,
+ 0xCE, 0xC0,
+};
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/drivers/char/tty_io.c linux-2.4.6-pre8-withA2232/drivers/char/tty_io.c
--- linux-2.4.6-pre8-vanilla/drivers/char/tty_io.c Tue Jul 3 01:42:58 2001
+++ linux-2.4.6-pre8-withA2232/drivers/char/tty_io.c Tue Jul 3 02:32:40 2001
@@ -2359,4 +2359,7 @@
#ifdef CONFIG_HWC
hwc_tty_init();
#endif
+#ifdef CONFIG_A2232
+ a2232board_init();
+#endif
}
diff -u --recursive --new-file linux-2.4.6-pre8-vanilla/include/linux/tty.h linux-2.4.6-pre8-withA2232/include/linux/tty.h
--- linux-2.4.6-pre8-vanilla/include/linux/tty.h Sat May 26 03:01:28 2001
+++ linux-2.4.6-pre8-withA2232/include/linux/tty.h Tue Jul 3 02:39:54 2001
@@ -366,6 +366,7 @@
extern int specialix_init(void);
extern int espserial_init(void);
extern int macserial_init(void);
+extern int a2232board_init(void);
extern int tty_paranoia_check(struct tty_struct *tty, kdev_t device,
const char *routine);
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2001-07-03 1:23 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2001-07-03 1:22 [DRIVER] patch against 2.4.6pre8 Linux A2232 Driver Project
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).