From: cb-lkml@fish.zetnet.co.uk
To: linux-kernel@vger.kernel.org
Subject: [2.5.68-mm2] [3c574_cs] irq 11: nobody cared
Date: Wed, 23 Apr 2003 22:49:55 +0100 [thread overview]
Message-ID: <20030423214955.GA602@fish.zetnet.co.uk> (raw)
2.5.68-mm2 gives the following message on ethernet activity. Network appears to
work fine.
lspci -vvv output also follows.
Previously reported problem with APM suspend to disk also still present.
Any more info needed?
Cheers
Charlie
handlers:
[<c8862450>] (el3_interrupt+0x0/0x240 [3c574_cs])
irq 11: nobody cared!
Call Trace:
[<c010b640>] handle_IRQ_event+0x90/0x100
[<c010b897>] do_IRQ+0x97/0x120
[<c0107000>] default_idle+0x0/0x40
[<c0107000>] default_idle+0x0/0x40
[<c0109c68>] common_interrupt+0x18/0x20
[<c0107000>] default_idle+0x0/0x40
[<c0107000>] default_idle+0x0/0x40
[<c0107024>] default_idle+0x24/0x40
[<c01070ba>] cpu_idle+0x3a/0x50
[<c0105000>] _stext+0x0/0x80
[<c02d8755>] start_kernel+0x135/0x140
[<c02d84b0>] unknown_bootoption+0x0/0x120
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 03)
Subsystem: Sony Corporation: Unknown device 805c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=64M]
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fc90 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at fca0 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:08.0 FireWire (IEEE 1394): Sony Corporation CXD3222 i.LINK Controller (rev 02) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 8060
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fedf7000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fedf7c00 (32-bit, non-prefetchable) [size=512]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: <available only to root>
00:09.0 Multimedia audio controller: Yamaha Corporation YMF-744B [DS-1S Audio Controller] (rev 02)
Subsystem: Sony Corporation: Unknown device 805e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fedf8000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at fcc0 [size=64]
Region 2: I/O ports at fc8c [size=4]
Capabilities: <available only to root>
00:0a.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 20) (prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 805d
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fe800000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at fec00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
00:0c.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
Subsystem: Sony Corporation: Unknown device 8061
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
next reply other threads:[~2003-04-23 21:37 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-04-23 21:49 cb-lkml [this message]
2003-04-23 23:05 ` [2.5.68-mm2] [3c574_cs] irq 11: nobody cared Andrew Morton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030423214955.GA602@fish.zetnet.co.uk \
--to=cb-lkml@fish.zetnet.co.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).