* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
@ 2003-08-24 12:06 Felipe Alfaro Solana
2003-08-24 12:10 ` Vojtech Pavlik
2003-08-24 13:13 ` Wiktor Wodecki
0 siblings, 2 replies; 6+ messages in thread
From: Felipe Alfaro Solana @ 2003-08-24 12:06 UTC (permalink / raw)
To: Vojtech Pavlik; +Cc: LKML, vojtech
----- Original Message -----
From: Vojtech Pavlik <vojtech@ucw.cz>
Date: Sun, 24 Aug 2003 12:46:15 +0200
To: Felipe Alfaro Solana <felipe_alfaro@linuxmail.org>
Subject: Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
> On Mon, Aug 18, 2003 at 09:09:16PM +0200, Felipe Alfaro Solana wrote:
>
> > If I try to boot my P4 box (i845DE motherboard) with no PS/2 mouse
> > plugged into the PS/2 port, the kernel hangs while checking the AUX
> > ports in function i8042_check_aux(). The i8042_check_aux() function is
> > trying to request IRQ #12, but the call to request_irq() causes the
> > hang. The kernel hangs exactly at:
> >
> > if (request_irq(values->irq, i8042_interrupt, SA_SHIRQ,
> > "i8042", i8042_request_irq_cookie))
>
> What happens if you remove the SA_SHIRQ and replace with 0?
It does nothing: the kernel still hangs there. It seems to be a problem with the new ACPI code
changes cause the kernel boots fine with "pci=noacpi".
--
______________________________________________
http://www.linuxmail.org/
Now with e-mail forwarding for only US$5.95/yr
Powered by Outblaze
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
2003-08-24 12:06 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached Felipe Alfaro Solana
@ 2003-08-24 12:10 ` Vojtech Pavlik
2003-08-24 13:13 ` Wiktor Wodecki
1 sibling, 0 replies; 6+ messages in thread
From: Vojtech Pavlik @ 2003-08-24 12:10 UTC (permalink / raw)
To: Felipe Alfaro Solana; +Cc: LKML, vojtech
On Sun, Aug 24, 2003 at 01:06:05PM +0100, Felipe Alfaro Solana wrote:
> ----- Original Message -----
> From: Vojtech Pavlik <vojtech@ucw.cz>
> Date: Sun, 24 Aug 2003 12:46:15 +0200
> To: Felipe Alfaro Solana <felipe_alfaro@linuxmail.org>
> Subject: Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
>
> > On Mon, Aug 18, 2003 at 09:09:16PM +0200, Felipe Alfaro Solana wrote:
> >
> > > If I try to boot my P4 box (i845DE motherboard) with no PS/2 mouse
> > > plugged into the PS/2 port, the kernel hangs while checking the AUX
> > > ports in function i8042_check_aux(). The i8042_check_aux() function is
> > > trying to request IRQ #12, but the call to request_irq() causes the
> > > hang. The kernel hangs exactly at:
> > >
> > > if (request_irq(values->irq, i8042_interrupt, SA_SHIRQ,
> > > "i8042", i8042_request_irq_cookie))
> >
> > What happens if you remove the SA_SHIRQ and replace with 0?
>
> It does nothing: the kernel still hangs there. It seems to be a problem with the new ACPI code
> changes cause the kernel boots fine with "pci=noacpi".
Most likely something with the polarity of interrupts.
--
Vojtech Pavlik
SuSE Labs, SuSE CR
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
2003-08-24 12:06 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached Felipe Alfaro Solana
2003-08-24 12:10 ` Vojtech Pavlik
@ 2003-08-24 13:13 ` Wiktor Wodecki
2003-08-24 19:40 ` Andrew Morton
1 sibling, 1 reply; 6+ messages in thread
From: Wiktor Wodecki @ 2003-08-24 13:13 UTC (permalink / raw)
To: Felipe Alfaro Solana; +Cc: Vojtech Pavlik, LKML, vojtech
[-- Attachment #1: Type: text/plain, Size: 10897 bytes --]
On Sun, Aug 24, 2003 at 01:06:05PM +0100, Felipe Alfaro Solana wrote:
> > On Mon, Aug 18, 2003 at 09:09:16PM +0200, Felipe Alfaro Solana wrote:
> >
> > > If I try to boot my P4 box (i845DE motherboard) with no PS/2 mouse
> > > plugged into the PS/2 port, the kernel hangs while checking the AUX
> > > ports in function i8042_check_aux(). The i8042_check_aux() function is
> > > trying to request IRQ #12, but the call to request_irq() causes the
> > > hang. The kernel hangs exactly at:
> > >
> > > if (request_irq(values->irq, i8042_interrupt, SA_SHIRQ,
> > > "i8042", i8042_request_irq_cookie))
> >
> > What happens if you remove the SA_SHIRQ and replace with 0?
>
> It does nothing: the kernel still hangs there. It seems to be a problem with the new ACPI code
> changes cause the kernel boots fine with "pci=noacpi".
confirmed here. Although I have it on 2.6.0-test4 and had it since
al least test3-mm3.
lspci -vvv:
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d9000000-dbffffff
Prefetchable memory behind bridge: dc000000-dcffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 9000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at 9400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at 9800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 7
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U (rev 01)
Subsystem: Adaptec AHA-2940UW SCSI Host Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 9c00 [disabled] [size=256]
Region 1: Memory at dd000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 04)
Subsystem: Triones Technologies, Inc. HPT370A
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 3 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc. Voodoo3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 9
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, prefetchable) [size=32M]
Region 2: I/O ports at b400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at b800 [size=128]
Region 1: Memory at dd001000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0d.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet (rev 02)
Subsystem: Silicon Integrated Systems [SiS] SiS900 10/100 Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at bc00 [size=256]
Region 1: Memory at dd002000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at c000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W [Millennium II] AGP (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc.: Unknown device 0100
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at d9000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [f0] AGP version 1.0
Status: RQ=1 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=<none>
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
--
Regards,
Wiktor Wodecki
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
2003-08-24 13:13 ` Wiktor Wodecki
@ 2003-08-24 19:40 ` Andrew Morton
2003-08-24 23:06 ` Felipe Alfaro Solana
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Morton @ 2003-08-24 19:40 UTC (permalink / raw)
To: Wiktor Wodecki; +Cc: felipe_alfaro, vojtech, linux-kernel, vojtech, linux-acpi
Wiktor Wodecki <wodecki@gmx.de> wrote:
>
> > > > if (request_irq(values->irq, i8042_interrupt, SA_SHIRQ,
> > > > "i8042", i8042_request_irq_cookie))
> > >
> > > What happens if you remove the SA_SHIRQ and replace with 0?
> >
> > It does nothing: the kernel still hangs there. It seems to be a problem with the new ACPI code
> > changes cause the kernel boots fine with "pci=noacpi".
>
> confirmed here. Although I have it on 2.6.0-test4 and had it since
> al least test3-mm3.
Guys, please send a full report to linux-acpi@intel.com based on
the following:
Regarding how to field these in general...
Bugzilla would be really helpful, because we've got multiple bugs and
multiple people working on them and bugzilla is better than e-mail at
keeping the relevant bits together. bugzilla with component=ACPI and
owner len.brown@intel.com or andrew.grover@intel.com should do the
trick.
The dmesg output of the failing case is really helpful,
As is the output of acpidmp to examine the ACPI tables on the system.
(Red Hat includes both of these in their severn beta1, acpidmp is also
in pmtools on intel's ACPI web page)
dmidecode output is useful to identify the BIOS version.
Of course the 1st thing to check with ACPI failures is that the BIOS
version shown by dmidmp is the latest provided by the vendor... Plus,
if we determine the BIOS is toast, DMI provides what we need to add the
system to the DMI or acpi blacklists.
We're seeting the most problems on VIA chip-sets with no IO-APIC.
The one below is unusual because it is a 2-way system with 3 IO-APICs.
The latest code in linus' tree includes ACPICA 20030813, which is
slightly newer than the one below, it might be a good idea to try that
with CONFIG_ACPI_DEBUG. Note that it will spit out the DMI info upon
the mount root failure automatically.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
2003-08-24 19:40 ` Andrew Morton
@ 2003-08-24 23:06 ` Felipe Alfaro Solana
0 siblings, 0 replies; 6+ messages in thread
From: Felipe Alfaro Solana @ 2003-08-24 23:06 UTC (permalink / raw)
To: LKML
On Sun, 2003-08-24 at 21:40, Andrew Morton wrote:
> Guys, please send a full report to linux-acpi@intel.com based on
> the following:
I filled in a bugzilla report a few days ago :-)
http://bugzilla.kernel.org/show_bug.cgi?id=1123
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached
[not found] <1061233756.1520.16.camel@teapot.felipe-alfaro.com>
@ 2003-08-24 10:46 ` Vojtech Pavlik
0 siblings, 0 replies; 6+ messages in thread
From: Vojtech Pavlik @ 2003-08-24 10:46 UTC (permalink / raw)
To: Felipe Alfaro Solana; +Cc: LKML, vojtech
On Mon, Aug 18, 2003 at 09:09:16PM +0200, Felipe Alfaro Solana wrote:
> If I try to boot my P4 box (i845DE motherboard) with no PS/2 mouse
> plugged into the PS/2 port, the kernel hangs while checking the AUX
> ports in function i8042_check_aux(). The i8042_check_aux() function is
> trying to request IRQ #12, but the call to request_irq() causes the
> hang. The kernel hangs exactly at:
>
> if (request_irq(values->irq, i8042_interrupt, SA_SHIRQ,
> "i8042", i8042_request_irq_cookie))
What happens if you remove the SA_SHIRQ and replace with 0?
> in drivers/input/serio/i8042.c, with a value of 12 for values->irq. If I
> boot with my PS/2 mouse attached, the kernel is able to boot normally.
> Also, disabling ACPI support in the kernel allows me to boot
> 2.6.0-test3-bk6 with no PS/2 mouse plugged in.
--
Vojtech Pavlik
SuSE Labs, SuSE CR
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2003-08-24 23:06 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-08-24 12:06 2.6.0-test3-bk6: hang at i8042.c when booting with no PS/2 mouse attached Felipe Alfaro Solana
2003-08-24 12:10 ` Vojtech Pavlik
2003-08-24 13:13 ` Wiktor Wodecki
2003-08-24 19:40 ` Andrew Morton
2003-08-24 23:06 ` Felipe Alfaro Solana
[not found] <1061233756.1520.16.camel@teapot.felipe-alfaro.com>
2003-08-24 10:46 ` Vojtech Pavlik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).