From: Duncan Sands <duncan.sands@wanadoo.fr>
To: linux-kernel@vger.kernel.org
Subject: Re: Problem with 2.6-testXX and alcatel speedtouch usb modem
Date: Mon, 25 Aug 2003 11:43:26 +0200 [thread overview]
Message-ID: <200308251143.26764.duncan.sands@wanadoo.fr> (raw)
In-Reply-To: <200308200203.02897.jjluza@yahoo.fr>
On Wednesday 20 August 2003 02:03, jjluza wrote:
> I try to make this modem working.
> It works very well on kernel 2.4 series.
> It work with some kernel 2.6 until test2-mm1.
> But since test2-mm1, the newer kernel doesn't work anymore.
> There is 2 related drivers for this modem.
> The one which is included in the kernel and which can be found here :
> http://www.linux-usb.org/SpeedTouch/
> and the one which I've always used until now :
> speedtouch.sourceforge.net
>
> when I notice that the old one doesn't work anymore, I try with the driver
> which included in the kernel, without success.
Did you follow the instructions on http://www.linux-usb.org/SpeedTouch/ ?
> It crashed when I do "pppd call adsl".
>From what I see below you are still using the userspace driver (pppoa3),
which is being called by pppd. This won't work when you have the kernel
module loaded. You need to use a pppoa aware pppd and not call pppd.
> I can load the firmware.
>
> And here is messages in syslog :
> Aug 19 22:00:26 serveur modem_run[337]: modem_run version 1.1 started by
> root uid 0
> Aug 19 22:00:28 serveur kernel: usb 1-2: bulk timeout on ep5in
> Aug 19 22:00:28 serveur kernel: usbfs: USBDEVFS_BULK failed dev 2 ep 0x85
> len 512 ret -110
> Aug 19 22:00:43 serveur modem_run[337]: ADSL synchronization has been
> obtained Aug 19 22:00:43 serveur modem_run[337]: ADSL line is up (608
> kbit/s down | 160 kbit/s up)
> Aug 19 22:00:43 serveur modprobe: FATAL: Module ipv6 not found.
> Aug 19 22:00:43 serveur pppd[345]: pppd 2.4.1 started by root, uid 0
> Aug 19 22:00:43 serveur pppd[345]: Using interface ppp0
> Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0
> Aug 19 22:00:44 serveur kernel: ip_conntrack version 2.1 (768 buckets, 6144
> max) - 300 bytes per conntrack
> Aug 19 22:00:44 serveur pppoa3[346]: PPPoA3 version 1.1 started by root
> (uid 0)
> Aug 19 22:00:44 serveur pppoa3[346]: Control thread ready
> Aug 19 22:00:44 serveur pppoa3[352]: ppp(d) --> pppoa3 --> modem stream
> ready Aug 19 22:00:44 serveur pppoa3[353]: modem --> pppoa3 --> ppp(d)
> stream ready Aug 19 22:00:44 serveur pppoa3[353]: Error reading usb urb
> Aug 19 22:00:44 serveur pppoa3[346]: Woken by a sem_post event -> Exiting
> Aug 19 22:00:44 serveur pppoa3[346]: Read from ppp Canceled
> Aug 19 22:00:44 serveur pppoa3[346]: Write to ppp Canceled
> Aug 19 22:00:44 serveur pppoa3[346]: Exiting
> Aug 19 22:00:44 serveur pppd[345]: Modem hangup
> Aug 19 22:00:44 serveur pppd[345]: Connection terminated.
> Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32
> Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a
> release() function, it is broken and must
> be fixed.
> Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at
> drivers/base/class.c:201
> Aug 19 22:00:44 serveur kernel: Call Trace:
> Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64]
> kobject_cleanup+0x36/0x40
> Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464]
> netdev_run_todo+0x10b/0x1d0
> Aug 19 22:00:44 serveur kernel: [_end+114517535/1070384712]
> ppp_shutdown_interface+0x87/0xe0 [ppp_generic]
> Aug 19 22:00:44 serveur kernel: [_end+114504362/1070384712]
> ppp_ioctl+0x802/0x820 [ppp_generic]
> Aug 19 22:00:44 serveur kernel: [__fput+193/288] __fput+0xc1/0x120
> Aug 19 22:00:44 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280
> Aug 19 22:00:44 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb
> Aug 19 22:00:44 serveur kernel:
> Aug 19 22:00:44 serveur kernel: ip_tables: (C) 2000-2002 Netfilter core
> team Aug 19 22:00:44 serveur pppd[345]: Using interface ppp0
> Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0
> Aug 19 22:00:44 serveur pppoa3[364]: PPPoA3 version 1.1 started by root
> (uid 0)
> Aug 19 22:00:44 serveur pppoa3[364]: Control thread ready
> Aug 19 22:00:44 serveur pppoa3[374]: ppp(d) --> pppoa3 --> modem stream
> ready Aug 19 22:00:44 serveur pppoa3[375]: modem --> pppoa3 --> ppp(d)
> stream ready Aug 19 22:00:44 serveur pppoa3[375]: Error reading usb urb
> Aug 19 22:00:44 serveur pppoa3[364]: Woken by a sem_post event -> Exiting
> Aug 19 22:00:44 serveur pppoa3[364]: Read from ppp Canceled
> Aug 19 22:00:44 serveur pppoa3[364]: Write to ppp Canceled
> Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32
> Aug 19 22:00:44 serveur pppoa3[364]: Exiting
> Aug 19 22:00:44 serveur pppd[345]: Modem hangup
> Aug 19 22:00:44 serveur pppd[345]: Connection terminated.
> Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a
> release() function, it is broken and must
> be fixed.
> Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at
> drivers/base/class.c:201
> Aug 19 22:00:44 serveur kernel: Call Trace:
> Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64]
> kobject_cleanup+0x36/0x40
> Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464]
> netdev_run_todo+0x10b/0x1d0
> Aug 19 22:00:44 serveur kernel: [_end+114517535/1070384712]
> ppp_shutdown_interface+0x87/0xe0 [ppp_generic]
> Aug 19 22:00:44 serveur kernel: [_end+114504362/1070384712]
> ppp_ioctl+0x802/0x820 [ppp_generic]
> Aug 19 22:00:44 serveur kernel: [__fput+193/288] __fput+0xc1/0x120
> Aug 19 22:00:44 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280
> Aug 19 22:00:44 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb
> Aug 19 22:00:44 serveur kernel:
> Aug 19 22:00:44 serveur pppoa3[386]: PPPoA3 version 1.1 started by root
> (uid 0)
> Aug 19 22:00:44 serveur pppoa3[386]: Control thread ready
> Aug 19 22:00:44 serveur pppoa3[389]: ppp(d) --> pppoa3 --> modem stream
> ready Aug 19 22:00:44 serveur pppoa3[390]: modem --> pppoa3 --> ppp(d)
> stream ready Aug 19 22:00:44 serveur pppoa3[390]: Error reading usb urb
> Aug 19 22:00:44 serveur pppoa3[386]: Woken by a sem_post event -> Exiting
> Aug 19 22:00:44 serveur pppoa3[386]: Read from ppp Canceled
> Aug 19 22:00:44 serveur pppoa3[386]: Write to ppp Canceled
> Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32
> Aug 19 22:00:44 serveur pppd[345]: Using interface ppp0
> Aug 19 22:00:44 serveur pppoa3[386]: Exiting
> Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0
> Aug 19 22:00:44 serveur pppd[345]: ioctl(PPPIOCSASYNCMAP): Inappropriate
> ioctl for device(25)
> Aug 19 22:00:44 serveur pppd[345]: tcflush failed: Input/output error
> Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a
> release() function, it is broken and must
> be fixed.
> Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at
> drivers/base/class.c:201
> Aug 19 22:00:44 serveur kernel: Call Trace:
> Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64]
> kobject_cleanup+0x36/0x40
> Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464]
> netdev_run_todo+0x10b/0x1d0
> Aug 19 22:00:45 serveur kernel: [_end+114517535/1070384712]
> ppp_shutdown_interface+0x87/0xe0 [ppp_generic]
> Aug 19 22:00:45 serveur kernel: [_end+114504362/1070384712]
> ppp_ioctl+0x802/0x820 [ppp_generic]
> Aug 19 22:00:45 serveur kernel: [__fput+193/288] __fput+0xc1/0x120
> Aug 19 22:00:45 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280
> Aug 19 22:00:45 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb
> Aug 19 22:00:45 serveur kernel:
> Aug 19 22:00:45 serveur pppd[345]: Exit.
>
>
> so, the last kernel which work with this adsl modem is test2-mm1.
It looks like usbfs is broken again. I should be able to look into
this next week. In the meantime, please try the kernel module.
All the best,
Duncan.
next parent reply other threads:[~2003-08-25 9:42 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <200308200203.02897.jjluza@yahoo.fr>
2003-08-25 9:43 ` Duncan Sands [this message]
2003-08-28 10:02 Problem with 2.6-testXX and alcatel speedtouch usb modem subodh
-- strict thread matches above, loose matches on Subject: below --
2003-08-26 3:43 jjluza
2003-08-27 19:57 ` Duncan Sands
2003-08-22 11:08 Luis Medinas
2003-08-23 0:22 ` Greg KH
2003-08-20 0:06 jjluza
2003-08-20 0:34 ` Greg KH
2003-08-20 1:23 ` jjluza
2003-08-20 1:38 ` John Levon
2003-08-20 2:23 ` jjluza
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200308251143.26764.duncan.sands@wanadoo.fr \
--to=duncan.sands@wanadoo.fr \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).