linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* PDC20265 problems with 2.4.23
@ 2003-12-06 12:17 Gergely Tamas
  0 siblings, 0 replies; only message in thread
From: Gergely Tamas @ 2003-12-06 12:17 UTC (permalink / raw)
  To: linux-kernel

Hi,

I get the following with kernel 2.4.23...

| [...]
|  PDC20265: IDE controller at PCI slot 00:0c.0
|  PDC20265: chipset revision 2
|  PDC20265: not 100%% native mode: will probe irqs later
|  PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
|      ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:pio
|      ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:DMA, hdh:DMA
| [...]
|  hde: Maxtor 5T040H4, ATA DISK drive
|  hdg: ST3120022A, ATA DISK drive
|  hdh: ST3120022A, ATA DISK drive
| [...]
|  ide2 at 0xcc00-0xcc07,0xd002 on irq 18
|  ide3 at 0xd400-0xd407,0xd802 on irq 18
|  hde: attached ide-disk driver.
|  hde: host protected area => 1
|  hde: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=79408/16/63
|  hdg: attached ide-disk driver.
|  hdg: host protected area => 1
|  hdg: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63
|  hdh: attached ide-disk driver.
|  hdh: host protected area => 1
|  hdh: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63
|  Partition check:
|   hde: [PTBL] [4982/255/63] hde1
|   hdg: hdg1 hdg2
|   hdh: hdh1
| [...]
|  hdg: status error: status=0x58 { DriveReady SeekComplete DataRequest }
|  
|  hdg: drive not ready for command
|  hdg: status error: status=0x50 { DriveReady SeekComplete }
|  
|  hdg: no DRQ after issuing MULTWRITE
|  hdg: status timeout: status=0xd0 { Busy }
|  
|  PDC202XX: Secondary channel reset.
|  PDC202XX: Primary channel reset.
|  hdg: no DRQ after issuing WRITE
|  ide3: reset: master: error (0x00?)
| [...]
|  hde: status error: status=0x51 { DriveReady SeekComplete Error }
|  hde: status error: error=0x04 { DriveStatusError }
|  hde: no DRQ after issuing MULTWRITE
|  hde: status error: status=0x51 { DriveReady SeekComplete Error }
|  hde: status error: error=0x04 { DriveStatusError }
|  hde: no DRQ after issuing MULTWRITE
|  hde: status error: status=0x51 { DriveReady SeekComplete Error }
|  hde: status error: error=0x04 { DriveStatusError }
|  hde: no DRQ after issuing MULTWRITE
|  hde: status error: status=0x51 { DriveReady SeekComplete Error }
|  hde: status error: error=0x04 { DriveStatusError }
|  PDC202XX: Primary channel reset.
|  PDC202XX: Secondary channel reset.
|  hde: no DRQ after issuing WRITE
| [...]
|  ide2: reset: master: error (0x00?)
| [...]
|  hdg: lost interrupt
|  hdg: lost interrupt
|  hdg: lost interrupt
| .
| .
| .

$ grep PDC .config
CONFIG_BLK_DEV_PDC202XX_OLD=y
CONFIG_PDC202XX_BURST=y
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
CONFIG_BLK_DEV_PDC202XX=y
# CONFIG_BLK_DEV_ATARAID_PDC is not set


Thanks in advance,
Gergely

^ permalink raw reply	[flat|nested] only message in thread

only message in thread, other threads:[~2003-12-06 12:17 UTC | newest]

Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-12-06 12:17 PDC20265 problems with 2.4.23 Gergely Tamas

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).