Bootdata ok (command line is ro root=/dev/md2 report_lost_ticks maxcpus=1 init=/bin/sh) Linux version 2.6.16-rc6-git4-mmio (rugolsky@ti94) (gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #4 SMP Wed Mar 15 20:48:51 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009b800 (usable) BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff10000 (usable) BIOS-e820: 000000007ff10000 - 000000007ff17000 (ACPI data) BIOS-e820: 000000007ff17000 - 000000007ff80000 (ACPI NVS) BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f7920 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x000000007ff127f1 ACPI: FADT (v001 NVIDIA CK8S 0x06040000 PTL_ 0x000f4240) @ 0x000000007ff16dd8 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x000000007ff16e4c ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x000000007ff16e9c ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x000000007ff16f1c ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x000000007ff16f58 ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x000000007ff16fd8 ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000 On node 0 totalpages: 514672 DMA zone: 1828 pages, LIFO batch:0 DMA32 zone: 512844 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 Nvidia board detected. Ignoring ACPI timer override. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: 2 duplicate APIC table ignored. ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:5 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:5 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xc0400000] gsi_base[24]) IOAPIC[1]: apic_id 3, version 17, address 0xc0400000, GSI 24-27 ACPI: IOAPIC (id[0x04] address[0xc0401000] gsi_base[28]) IOAPIC[2]: apic_id 4, version 17, address 0xc0401000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) Checking aperture... CPU 0: aperture @ bc000000 size 64 MB CPU 1: aperture @ bc000000 size 64 MB Built 1 zonelists Kernel command line: ro root=/dev/md2 report_lost_ticks maxcpus=1 init=/bin/sh Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) Disabling vsyscall due to use of PM timer time.c: Using 3.579545 MHz WALL PM GTOD PM timer. time.c: Detected 2009.273 MHz processor. Console: colour VGA+ 80x25 time.c: Lost 495 timer tick(s)! rip start_kernel+0x102/0x1cc) Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 2053752k/2096192k available (1985k kernel code, 41716k reserved, 1053k data, 180k init) Calibrating delay using timer specific routine.. 4023.40 BogoMIPS (lpj=2011702) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) time.c: Lost 2 timer tick(s)! rip acpi_os_write_port+0x22/0x42) Using local APIC timer interrupts. result 12557972 Detected 12.557 MHz APIC timer. time.c: Lost 49 timer tick(s)! rip setup_boot_APIC_clock+0x121/0x127) Brought up 1 CPUs testing NMI watchdog ... OK. migration_cost=0 checking if image is initramfs... it is Freeing initrd memory: 1289k freed DMI present. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Transparent bridge - 0000:00:09.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Root Bridge [PCI2] (0000:08) PCI: Probing PCI hardware (bus 08) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 ACPI: PCI Root Bridge [PCI1] (0000:80) PCI: Probing PCI hardware (bus 80) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:81:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.XVR0._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-DMA: Disabling IOMMU. pnp: 00:02: ioport range 0x8000-0x807f could not be reserved pnp: 00:02: ioport range 0x8080-0x80ff has been reserved pnp: 00:02: ioport range 0x8400-0x847f has been reserved pnp: 00:02: ioport range 0x8480-0x84ff has been reserved pnp: 00:02: ioport range 0x8800-0x887f has been reserved pnp: 00:02: ioport range 0x8880-0x88ff has been reserved pnp: 00:02: ioport range 0xa000-0xa03f has been reserved pnp: 00:02: ioport range 0xa040-0xa07f has been reserved PCI: Bridge: 0000:00:09.0 IO window: disabled. MEM window: c0100000-c01fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Bridge: 0000:80:0e.0 IO window: 3000-3fff MEM window: c0900000-c09fffff PREFETCH window: d0000000-dfffffff PCI: Setting latency timer of device 0000:80:0e.0 to 64 Simple Boot Flag at 0x36 set to 0x1 IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1142476264.041:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) time.c: Lost 202 timer tick(s)! rip __do_softirq+0x45/0xc8) PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] PCI: Setting latency timer of device 0000:80:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:80:0e.0:pcie00] Allocate Port Service[0000:80:0e.0:pcie03] Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 NFORCE-CK804: chipset revision 242 NFORCE-CK804: not 100% native mode: will probe irqs later NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller ide0: BM-DMA at 0x1c00-0x1c07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1c08-0x1c0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 180k freed SCSI subsystem initialized libata version 1.20 loaded. sata_nv 0000:00:07.0: version 0.8 ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23 GSI 16 sharing vector 0xB1 and IRQ 16 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:07.0 to 64 PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0xFFFFC20000004480 ctl 0xFFFFC200000044A0 bmdma 0x1C10 irq 16 ata2: SATA max UDMA/133 cmd 0xFFFFC20000004580 ctl 0xFFFFC200000045A0 bmdma 0x1C18 irq 16 input: AT Translated Set 2 keyboard as /class/input/input0 ata1: SATA link up 3.0 Gbps (SStatus 123) ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3d01 87:4763 88:407f ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_nv ata2: SATA link down (SStatus 0) scsi1 : sata_nv Vendor: ATA Model: HDS728080PLA380 Rev: PF2O Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sd 0:0:0:0: Attached scsi disk sda ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22 GSI 17 sharing vector 0xB9 and IRQ 17 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:08.0 to 64 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0xFFFFC20000006480 ctl 0xFFFFC200000064A0 bmdma 0x1C20 irq 17 ata4: SATA max UDMA/133 cmd 0xFFFFC20000006580 ctl 0xFFFFC200000065A0 bmdma 0x1C28 irq 17 ata3: SATA link up 1.5 Gbps (SStatus 113) ata3: dev 0 cfg 49:2f00 82:74eb 83:7f63 84:4003 85:74e9 86:3d43 87:4003 88:007f ata3: dev 0 ATA-6, max UDMA/133, 145226112 sectors: LBA48 ata3: dev 0 configured for UDMA/133 scsi2 : sata_nv ata4: SATA link up 1.5 Gbps (SStatus 113) ata4: dev 0 cfg 49:2f00 82:74eb 83:7f63 84:4003 85:74e9 86:3d43 87:4003 88:007f ata4: dev 0 ATA-6, max UDMA/133, 145226112 sectors: LBA48 ata4: dev 0 configured for UDMA/133 scsi3 : sata_nv Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 > sd 2:0:0:0: Attached scsi disk sdb Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 > sd 3:0:0:0: Attached scsi disk sdc device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com md: raid1 personality registered for level 1 md: Autodetecting RAID arrays. md: autorun ... md: considering sdc5 ... md: adding sdc5 ... md: sdc3 has different UUID to sdc5 md: sdc2 has different UUID to sdc5 md: sdc1 has different UUID to sdc5 md: adding sdb5 ... md: sdb3 has different UUID to sdc5 md: sdb2 has different UUID to sdc5 md: sdb1 has different UUID to sdc5 md: created md5 md: bind md: bind md: running: md: md5: raid array is not clean -- starting background reconstruction raid1: raid set md5 active with 2 out of 2 mirrors md: considering sdc3 ... md: syncing RAID array md5 md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. md: using 128k window, over a total of 70838464 blocks. md: adding sdc3 ... md: sdc2 has different UUID to sdc3 md: sdc1 has different UUID to sdc3 md: adding sdb3 ... md: sdb2 has different UUID to sdc3 md: sdb1 has different UUID to sdc3 md: created md3 md: bind md: bind md: running: raid1: raid set md3 active with 2 out of 2 mirrors md: considering sdc2 ... md: adding sdc2 ... md: sdc1 has different UUID to sdc2 md: adding sdb2 ... md: sdb1 has different UUID to sdc2 md: created md2 md: bind md: bind md: running: md: md2: raid array is not clean -- starting background reconstruction raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdc1 ... md: delaying resync of md2 until md5 has finished resync (they share one or more physical units) md: adding sdc1 ... md: adding sdb1 ... md: created md1 md: bind md: bind md: running: raid1: raid set md1 active with 2 out of 2 mirrors md: ... autorun DONE. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ( events/0-5 |#0): new 5 us maximum-latency wakeup. ( events/0-5 |#0): new 7 us maximum-latency wakeup. ( events/0-5 |#0): new 8 us maximum-latency wakeup. ( events/0-5 |#0): new 15 us maximum-latency wakeup. ( events/0-5 |#0): new 16 us maximum-latency wakeup. ata4: command 0x35 timeout, stat 0x50 ( md5_resync-677 |#0): new 34 us maximum-latency wakeup. ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ( kblockd/0-14 |#0): new 54 us maximum-latency wakeup. ata4: command 0x35 timeout, stat 0x50 EXT3 FS on sda1, internal journal ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50 ata4: command 0x35 timeout, stat 0x50