Re: [BUG] USB_PERSIST

[Andrew Morton <akpm@linux-foundation.org>]

On Tue, 20 Nov 2007 17:04:32 -0700 "Raymano Garibaldi" <raymano@faunos.com> wrote:

> Is there any other information that I can provide which might help in
> resolving this bug?

Let's cc the USB developers.

> On 11/18/07, Raymano Garibaldi <raymano@faunos.com> wrote:
> > The last time I tried this and it worked was 2.6.21. Below is a
> > portion of the kernel log file where I had a USB storage device
> > attached to the computer, then suspended the computer, while computer
> > was suspended detached and reattached the USB storage device, and
> > resumed the computer.
> >
> > --------------------------------------------------------------------------------------------------------------------------------
> > Nov 18 23:07:42 myfaun Stopping tasks ... done.
> > Nov 18 23:07:42 myfaun Suspending console(s)
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Synchronizing SCSI cache
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Stopping disk
> > Nov 18 23:07:42 myfaun ACPI handle has no context!
> > Nov 18 23:07:42 myfaun ACPI handle has no context!
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1f.2 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1f.1 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1d.7 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1d.3 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1d.2 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1d.1 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1d.0 disabled
> > Nov 18 23:07:42 myfaun ACPI: PCI interrupt for device 0000:00:1b.0 disabled
> > Nov 18 23:07:42 myfaun Disabling non-boot CPUs ...
> > Nov 18 23:07:42 myfaun CPU 1 is now offline
> > Nov 18 23:07:42 myfaun SMP alternatives: switching to UP code
> > Nov 18 23:07:42 myfaun CPU1 is down
> > Nov 18 23:07:42 myfaun Intel machine check architecture supported.
> > Nov 18 23:07:42 myfaun Intel machine check reporting enabled on CPU#0.
> > Nov 18 23:07:42 myfaun CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
> > Nov 18 23:07:42 myfaun CPU0: Thermal monitoring enabled
> > Nov 18 23:07:42 myfaun Back to C!
> > Nov 18 23:07:42 myfaun Enabling non-boot CPUs ...
> > Nov 18 23:07:42 myfaun SMP alternatives: switching to SMP code
> > Nov 18 23:07:42 myfaun Booting processor 1/1 eip 3000
> > Nov 18 23:07:42 myfaun Initializing CPU#1
> > Nov 18 23:07:42 myfaun Calibrating delay using timer specific
> > routine.. 6004.38 BogoMIPS (lpj=10003815)
> > Nov 18 23:07:42 myfaun CPU: After generic identify, caps: bfebfbff
> > 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
> > Nov 18 23:07:42 myfaun monitor/mwait feature present.
> > Nov 18 23:07:42 myfaun CPU: Trace cache: 12K uops, L1 D cache: 16K
> > Nov 18 23:07:42 myfaun CPU: L2 cache: 2048K
> > Nov 18 23:07:42 myfaun CPU: Physical Processor ID: 0
> > Nov 18 23:07:42 myfaun CPU: Processor Core ID: 1
> > Nov 18 23:07:42 myfaun CPU: After all inits, caps: bfebfbff 20100000
> > 00000000 0000b180 0000e49d 00000000 00000001 00000000
> > Nov 18 23:07:42 myfaun Intel machine check architecture supported.
> > Nov 18 23:07:42 myfaun Intel machine check reporting enabled on CPU#1.
> > Nov 18 23:07:42 myfaun CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
> > Nov 18 23:07:42 myfaun CPU1: Thermal monitoring enabled
> > Nov 18 23:07:42 myfaun CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
> > Nov 18 23:07:42 myfaun CPU1 is up
> > Nov 18 23:07:42 myfaun ACPI: Unable to turn cooling device [dfe34dc8] 'off'
> > Nov 18 23:07:42 myfaun Switched to high resolution mode on CPU 1
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16
> > (level, low) -> IRQ 19
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1b.0 at offset f (was 100, writing 105)
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1b.0 at offset 3 (was 0, writing 8)
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16
> > (level, low) -> IRQ 19
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1b.0 to 64
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23
> > (level, low) -> IRQ 18
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1d.0 to 64
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19
> > (level, low) -> IRQ 17
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1d.1 to 64
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18
> > (level, low) -> IRQ 16
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1d.2 to 64
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16
> > (level, low) -> IRQ 19
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1d.3 to 64
> > Nov 18 23:07:42 myfaun PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23
> > (level, low) -> IRQ 18
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1d.7 to 64
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1d.7 at offset f (was 100, writing 107)
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1e.0 to 64
> > Nov 18 23:07:42 myfaun PM: Writing back config space on device
> > 0000:00:1f.1 at offset 8 (was f001, writing fa01)
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18
> > (level, low) -> IRQ 16
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1f.1 to 64
> > Nov 18 23:07:42 myfaun ata2: port disabled. ignoring.
> > Nov 18 23:07:42 myfaun ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19
> > (level, low) -> IRQ 17
> > Nov 18 23:07:42 myfaun PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > Nov 18 23:07:42 myfaun pnp: Failed to activate device 00:07.
> > Nov 18 23:07:42 myfaun pnp: Failed to activate device 00:08.
> > Nov 18 23:07:42 myfaun e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
> > Nov 18 23:07:42 myfaun ata4: SATA link down (SStatus 0 SControl 300)
> > Nov 18 23:07:42 myfaun ata6: SATA link down (SStatus 0 SControl 300)
> > Nov 18 23:07:42 myfaun ata5: SATA link down (SStatus 0 SControl 300)
> > Nov 18 23:07:42 myfaun ata1.00: configured for UDMA/33
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Starting disk
> > Nov 18 23:07:42 myfaun ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > Nov 18 23:07:42 myfaun ata3.00: configured for UDMA/100
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] 488397168 512-byte hardware
> > sectors (250059 MB)
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Write Protect is off
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
> > Nov 18 23:07:42 myfaun sd 2:0:0:0: [sda] Write cache: enabled, read
> > cache: enabled, doesn't support DPO or FUA
> > Nov 18 23:07:42 myfaun Restarting tasks ... <6>usb 5-6: USB
> > disconnect, address 5
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] READ CAPACITY failed
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] Result: hostbyte=0x01 driverbyte=0x00
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] Sense not available.
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] Write Protect is off
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] Mode Sense: 00 00 00 00
> > Nov 18 23:07:42 myfaun sd 9:0:0:0: [sdf] Assuming drive cache: write through
> > Nov 18 23:07:42 myfaun done.
> > Nov 18 23:07:42 myfaun usb 5-6: new high speed USB device using
> > ehci_hcd and address 6
> > Nov 18 23:07:42 myfaun usb 5-6: configuration #1 chosen from 1 choice
> > Nov 18 23:07:42 myfaun scsi10 : SCSI emulation for USB Mass Storage devices
> > Nov 18 23:07:42 myfaun usb-storage: device found at 6
> > Nov 18 23:07:42 myfaun usb-storage: waiting for device to settle before scanning
> > Nov 18 23:07:48 myfaun scsi 10:0:0:0: Direct-Access     USB 2.0  Flash
> > Disk       1.00 PQ: 0 ANSI: 2
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] 1982464 512-byte hardware
> > sectors (1015 MB)
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Write Protect is off
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Mode Sense: 03 00 00 00
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Assuming drive cache: write through
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] 1982464 512-byte hardware
> > sectors (1015 MB)
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Write Protect is off
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Mode Sense: 03 00 00 00
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Assuming drive cache: write through
> > Nov 18 23:07:48 myfaun sdg: sdg1 sdg2
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: [sdg] Attached SCSI removable disk
> > Nov 18 23:07:48 myfaun sd 10:0:0:0: Attached scsi generic sg6 type 0
> > Nov 18 23:07:48 myfaun usb-storage: device scan complete
> >
> > --------------------------------------------------------------------------------------------------------------------------------
> >
> > Thanks,
> > Raymano G.
> >
> > On 11/18/07, Denys Vlasenko <vda.linux@googlemail.com> wrote:
> > > On Sunday 18 November 2007 20:14, Raymano Garibaldi wrote:
> > > > In kernel 2.6.23.8 USB_PERSIST feature does not work if the same USB
> > > > device is detached and reattached while computer is suspended. The
> > > > mount points for the USB storage device mounted before suspend are
> > > > lost and the device has to be remounted after resume.
> > >
> > > Does it work in 2.6.23.7? What messages you see in the kernel logs
> > > (in both kernels, good and bad)?
> > > --
> > > vda
> > >
> >

The report is a bit of a mess due to top-posting, but I guess people can work
it out.

If this doesn't get fixed within a few days please be sure to raise a
report against USB at bugzilla.kernel.org and check the "regression" box,
thanks.