linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [BUG] New Kernel Bugs
@ 2007-11-13  6:42 Natalie Protasevich
  2007-11-13 11:15 ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Natalie Protasevich @ 2007-11-13  6:42 UTC (permalink / raw)
  To: linux-kernel, akpm, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

This is the listing of the open bugs that are relatively new, around
2.6.22 and up. They are vaguely classified by specific area.
(not a full list, there are more :)

The good part is that reporters of the bugs below are still around and
haven't dissipated, or disposed of their hardware, so it is a good
time to get the bugs.
Those bugzillas that have been started as regressions on Rafael's list
are not mentioned here so far, since they are being tracked as new
regressions already.

It would be appreciated if the corresponding maintenance team could take a
look, close off any which are fixed and see if they can fix any which aren't.

NOTE: when replying to this email, please add the bug number to the Subject in
the form [Bug 1234] so that bugzilla will capture the discussion.
Thanks.

ACPI====================================================================

System does not load without acpi=off ide=nodma noapic
http://bugzilla.kernel.org/show_bug.cgi?id=9358
Kernel: 2.6.23.1

ACPI Error attaching device data
http://bugzilla.kernel.org/show_bug.cgi?id=9354
Kernel: 2.6.24-rc2

/proc/acpi/battery displays Incorrect voltages
http://bugzilla.kernel.org/show_bug.cgi?id=9341
Kernel: 2.6.23.1

PATA scan: ACPI Exception AE_AML_PACKAGE_LIMIT... is beyond end of object
http://bugzilla.kernel.org/show_bug.cgi?id=9320
Kernel: 2.6.24-rc2
(Tejun: calling _GTF without calling _STM first.  _GTM doesn't have any
prerequisite (it can't).  Can someone familiar with ACPI tell me why the method
is failing?  At any rate, libata should work fine regardless of ACPI failures.
Maybe it's time to start blacklist to skip ATA-ACPI for some boards to avoid
those annoying messages during boot)

ACPI Battery Info in /sys but not /proc/acpi
http://bugzilla.kernel.org/show_bug.cgi?id=9183
Kernel: 2.6.23-rc8-mm2

When using ACPI on a Compaq Presario V6221EU the laptop goes into
deadlock after a random amount of time
http://bugzilla.kernel.org/show_bug.cgi?id=9118
Kernel: 2.6.23-rc6

ACPI video driver should validate brightness level before setting it via _BCM
http://bugzilla.kernel.org/show_bug.cgi?id=9277
Kernel: 2.6.23

VIDEO/DVB

dvb driver reboot system
http://bugzilla.kernel.org/show_bug.cgi?id=9357
Kernel: 2.6.21.5


PLATFORM===============================================================

xipImage is built so that uBoot cant run it (ARM)
http://bugzilla.kernel.org/show_bug.cgi?id=9356
Kernel: 2.6.21

Samsung R20 - ACPI: PCI Root Bridge [PCI0] (0000:00)	
http://bugzilla.kernel.org/show_bug.cgi?id=9339
Kernel: 2.6.24
(boot is very long
..MP-BIOS bug: 8254 timer not connected to IO-APIC
then the boot stop at :
ACPI: PCI Root Bridge [PCI0] (0000:00)
(during 3 minutes, and boot continue)

system_64.h: switch_to inline asm should be more robbust wrt optimizations
http://bugzilla.kernel.org/show_bug.cgi?id=9302
Kernel: 2.6.24-rc1

with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
boot (ARM, Timer)
http://bugzilla.kernel.org/show_bug.cgi?id=9229
Kernel: 2.6.23

NETWORKING===========================================================

RTNLGRP_ND_USEROPT does not report ifindex (IPv6)
http://bugzilla.kernel.org/show_bug.cgi?id=9349
Kernel: 2.6.24+

a kernel error happend in the func: __skb_dequeue when using in
pfifo_fast_dequeue
http://bugzilla.kernel.org/show_bug.cgi?id=9342
Kernel: 2.6.11.1 - reporter asked to try recent kernel

e100 does not work after boot
http://bugzilla.kernel.org/show_bug.cgi?id=9336
Kernel: 2.6.23.1

2.6.23.1-smp kernel panic (network-related)
http://bugzilla.kernel.org/show_bug.cgi?id=9318
Kernel: 2.6.23.1
Infiniband panic

sundance -> 4port D-Link System Inc DFE-580TX -> Log errors
http://bugzilla.kernel.org/show_bug.cgi?id=9311
Kernel: 2.6.22.9

via-rhine driver stalls with: PHY status 786d, resetting...
http://bugzilla.kernel.org/show_bug.cgi?id=9300
Kernel: 2.6.23+


Weird network problems with 2.6.23-rc2
http://bugzilla.kernel.org/show_bug.cgi?id=9080
http://lkml.org/lkml/2007/8/11/40 - description

rt2500pci: low TCP throughput (wireless)
http://bugzilla.kernel.org/show_bug.cgi?id=9273
Kernel: 2.6.24-rc1
This is a regression

Unable to build wifi network between zd1201 and b43
http://bugzilla.kernel.org/show_bug.cgi?id=9237
Kernel: 2.6.24-rc1

Crash after module unload in b43 (wireless)
http://bugzilla.kernel.org/show_bug.cgi?id=9233
Kernel: 2.6.24-rc1

(net typhoon) "no descs for cmd, had (needed) 0 (1) cmd, 31 (7) resp"
http://bugzilla.kernel.org/show_bug.cgi?id=9225
Kernel: 2.6.23.1


IDE/SATA=========================================================

pata_pdc202xx_old excessive ATA bus errors
http://bugzilla.kernel.org/show_bug.cgi?id=9337
2.6.24-rc2

Drive seagate ST380011AS needs to be blacklisted
http://bugzilla.kernel.org/show_bug.cgi?id=9309
Kernel: 2.6.22.X

DVD-RAM umount and disk free bug
http://bugzilla.kernel.org/show_bug.cgi?id=9265
Kernel: 2.6.15  (asked to try current kernel)

FILE SYSTEMS=======================================================

ext4: delalloc space accounting problem drops data
http://bugzilla.kernel.org/show_bug.cgi?id=9329
Kernel: 2.6.24-rc1

POSIX Access Control Lists cause bogus file system check errors
http://bugzilla.kernel.org/show_bug.cgi?id=9241
Kernel: 2.6.23.1

MEMORY MANAGEMENT================================================

My system hangs when it has no more free memory to allocate via malloc()
http://bugzilla.kernel.org/show_bug.cgi?id=9316
Kernel: 2.6.23
User program, "My system hangs when it has no more free memory to
allocate via malloc()"

BUG: unable to handle kernel paging request at virtual address
26121228/kswapd0[231] exited with preempt_count 1
http://bugzilla.kernel.org/show_bug.cgi?id=9305
EIP is at free_block+0x6d/0xe4
Kernel: 2.6.22.6

POWER MANAGEMENT==================================================

IBM X41 looses time after Suspend2Disk
http://bugzilla.kernel.org/show_bug.cgi?id=9314
Kernel: 2.6.23

Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
http://bugzilla.kernel.org/show_bug.cgi?id=9275
Kernel: 2.6.23
This is HP notebook nc6320 T2400 945GM


VIDEO DRIVERS========================================================

No text consoles with FRAMEBUFFER_CONSOLE_DETECT_PRIMARY
http://bugzilla.kernel.org/show_bug.cgi?id=9310
Kernel: 2.6.24-rc1
This is a regression


PARALLEL PORT========================================================

LPC IT8705 POST port making noise on parallel port
http://bugzilla.kernel.org/show_bug.cgi?id=9306
Kernel: 2.6.16+


I/O STORAGE===========================================================

kernel bug from pktcdvd
http://bugzilla.kernel.org/show_bug.cgi?id=9294
Kernel: 2.6.23

After pci-e video card was installed, pci add-on usb card & firewire card fail
http://bugzilla.kernel.org/show_bug.cgi?id=9223
Kernel: 2.6.20 (testing of latest kernel requested)

SCSI==================================================================

qla2xxx: driver initialization does not complete when booting with
Port connected
http://bugzilla.kernel.org/show_bug.cgi?id=9267
Kernel: 2.6.23.1

SOUND ALSA============================================================

Unable to load snd-hda-intel module: Unknown symbol in module, or
unknown parameter
http://bugzilla.kernel.org/show_bug.cgi?id=9242
Kernel: 2.6.24-rc1

usbaudio microphone: regular sound distortion on several Logitech Webcams
http://bugzilla.kernel.org/show_bug.cgi?id=9230
Kernel: 2.6.22.9

HID====================================================================

Kernel NULL pointer dereference at :usbhid:hiddev_ioctl+0x2f/0xabc
http://bugzilla.kernel.org/show_bug.cgi?id=9216
Kernel: 2.6.23.1
Looks like this is a regression

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13  6:42 [BUG] New Kernel Bugs Natalie Protasevich
@ 2007-11-13 11:15 ` Andrew Morton
  2007-11-13 11:24   ` Jens Axboe
                     ` (11 more replies)
  0 siblings, 12 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 11:15 UTC (permalink / raw)
  To: Natalie Protasevich
  Cc: linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich" <protasnb@gmail.com> wrote:

> This is the listing of the open bugs that are relatively new, around
> 2.6.22 and up. They are vaguely classified by specific area.
> (not a full list, there are more :)
> 
> The good part is that reporters of the bugs below are still around and
> haven't dissipated, or disposed of their hardware, so it is a good
> time to get the bugs.
> Those bugzillas that have been started as regressions on Rafael's list
> are not mentioned here so far, since they are being tracked as new
> regressions already.

Thanks.

> It would be appreciated if the corresponding maintenance team could take a
> look, close off any which are fixed and see if they can fix any which aren't.
> 
> NOTE: when replying to this email, please add the bug number to the Subject in
> the form [Bug 1234] so that bugzilla will capture the discussion.
> Thanks.

You're optimistic.



> ACPI====================================================================
> 
> System does not load without acpi=off ide=nodma noapic
> http://bugzilla.kernel.org/show_bug.cgi?id=9358
> Kernel: 2.6.23.1

One response from a developer

> ACPI Error attaching device data
> http://bugzilla.kernel.org/show_bug.cgi?id=9354
> Kernel: 2.6.24-rc2

Zero responses from developers

> /proc/acpi/battery displays Incorrect voltages
> http://bugzilla.kernel.org/show_bug.cgi?id=9341
> Kernel: 2.6.23.1

Zero responses from developers

> PATA scan: ACPI Exception AE_AML_PACKAGE_LIMIT... is beyond end of object
> http://bugzilla.kernel.org/show_bug.cgi?id=9320
> Kernel: 2.6.24-rc2
> (Tejun: calling _GTF without calling _STM first.  _GTM doesn't have any
> prerequisite (it can't).  Can someone familiar with ACPI tell me why the method
> is failing?  At any rate, libata should work fine regardless of ACPI failures.
> Maybe it's time to start blacklist to skip ATA-ACPI for some boards to avoid
> those annoying messages during boot)

Tejun doing stuff

> ACPI Battery Info in /sys but not /proc/acpi
> http://bugzilla.kernel.org/show_bug.cgi?id=9183
> Kernel: 2.6.23-rc8-mm2

Marked as a duplicate of an already-resolved bug.

> 
> When using ACPI on a Compaq Presario V6221EU the laptop goes into
> deadlock after a random amount of time
> http://bugzilla.kernel.org/show_bug.cgi?id=9118
> Kernel: 2.6.23-rc6

Someone called Jike Song is trying to help out.  Regular developers awol.

> 
> ACPI video driver should validate brightness level before setting it via _BCM
> http://bugzilla.kernel.org/show_bug.cgi?id=9277
> Kernel: 2.6.23

Zero responses from developers

> VIDEO/DVB
> 
> dvb driver reboot system
> http://bugzilla.kernel.org/show_bug.cgi?id=9357
> Kernel: 2.6.21.5

Mauro thinks it might be bad hardware

> 
> PLATFORM===============================================================
> 
> xipImage is built so that uBoot cant run it (ARM)
> http://bugzilla.kernel.org/show_bug.cgi?id=9356
> Kernel: 2.6.21

Zero responses from developers

> 
> Samsung R20 - ACPI: PCI Root Bridge [PCI0] (0000:00)	
> http://bugzilla.kernel.org/show_bug.cgi?id=9339
> Kernel: 2.6.24
> (boot is very long
> ..MP-BIOS bug: 8254 timer not connected to IO-APIC
> then the boot stop at :
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> (during 3 minutes, and boot continue)

No response from developers

> system_64.h: switch_to inline asm should be more robbust wrt optimizations
> http://bugzilla.kernel.org/show_bug.cgi?id=9302
> Kernel: 2.6.24-rc1

Not really a bug.

> with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
> boot (ARM, Timer)
> http://bugzilla.kernel.org/show_bug.cgi?id=9229
> Kernel: 2.6.23

No response from developers

> NETWORKING===========================================================
> 
> RTNLGRP_ND_USEROPT does not report ifindex (IPv6)
> http://bugzilla.kernel.org/show_bug.cgi?id=9349
> Kernel: 2.6.24+

No response from developers

> a kernel error happend in the func: __skb_dequeue when using in
> pfifo_fast_dequeue
> http://bugzilla.kernel.org/show_bug.cgi?id=9342
> Kernel: 2.6.11.1 - reporter asked to try recent kernel

No response from developers

> e100 does not work after boot
> http://bugzilla.kernel.org/show_bug.cgi?id=9336
> Kernel: 2.6.23.1

No response from developers

> 2.6.23.1-smp kernel panic (network-related)
> http://bugzilla.kernel.org/show_bug.cgi?id=9318
> Kernel: 2.6.23.1
> Infiniband panic

No response from developers

> sundance -> 4port D-Link System Inc DFE-580TX -> Log errors
> http://bugzilla.kernel.org/show_bug.cgi?id=9311
> Kernel: 2.6.22.9

No response from developers

> via-rhine driver stalls with: PHY status 786d, resetting...
> http://bugzilla.kernel.org/show_bug.cgi?id=9300
> Kernel: 2.6.23+

No response from developers

> 
> Weird network problems with 2.6.23-rc2
> http://bugzilla.kernel.org/show_bug.cgi?id=9080
> http://lkml.org/lkml/2007/8/11/40 - description

No response from developers

> rt2500pci: low TCP throughput (wireless)
> http://bugzilla.kernel.org/show_bug.cgi?id=9273
> Kernel: 2.6.24-rc1
> This is a regression

No response from developers

> Unable to build wifi network between zd1201 and b43
> http://bugzilla.kernel.org/show_bug.cgi?id=9237
> Kernel: 2.6.24-rc1

No response from developers

> Crash after module unload in b43 (wireless)
> http://bugzilla.kernel.org/show_bug.cgi?id=9233
> Kernel: 2.6.24-rc1

No response from developers

> (net typhoon) "no descs for cmd, had (needed) 0 (1) cmd, 31 (7) resp"
> http://bugzilla.kernel.org/show_bug.cgi?id=9225
> Kernel: 2.6.23.1

No response from developers

> 
> IDE/SATA=========================================================
> 
> pata_pdc202xx_old excessive ATA bus errors
> http://bugzilla.kernel.org/show_bug.cgi?id=9337
> 2.6.24-rc2

No response from developers

> Drive seagate ST380011AS needs to be blacklisted
> http://bugzilla.kernel.org/show_bug.cgi?id=9309
> Kernel: 2.6.22.X

Jeff and Tehun did some stuff.

> DVD-RAM umount and disk free bug
> http://bugzilla.kernel.org/show_bug.cgi?id=9265
> Kernel: 2.6.15  (asked to try current kernel)

No response from developers

> FILE SYSTEMS=======================================================
> 
> ext4: delalloc space accounting problem drops data
> http://bugzilla.kernel.org/show_bug.cgi?id=9329
> Kernel: 2.6.24-rc1

No response from developers

> POSIX Access Control Lists cause bogus file system check errors
> http://bugzilla.kernel.org/show_bug.cgi?id=9241
> Kernel: 2.6.23.1

Andreas did some work, seemed to lose interest.

> MEMORY MANAGEMENT================================================
> 
> My system hangs when it has no more free memory to allocate via malloc()
> http://bugzilla.kernel.org/show_bug.cgi?id=9316
> Kernel: 2.6.23
> User program, "My system hangs when it has no more free memory to
> allocate via malloc()"

Rafael poked Thomas a week ago, to no effect. Thomas has been travelling.

> BUG: unable to handle kernel paging request at virtual address
> 26121228/kswapd0[231] exited with preempt_count 1
> http://bugzilla.kernel.org/show_bug.cgi?id=9305
> EIP is at free_block+0x6d/0xe4
> Kernel: 2.6.22.6

No response from developers

> POWER MANAGEMENT==================================================
> 
> IBM X41 looses time after Suspend2Disk
> http://bugzilla.kernel.org/show_bug.cgi?id=9314
> Kernel: 2.6.23

Rafael poked Thomas a week ago, to no effect.  Thomas has been travelling.

> Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> http://bugzilla.kernel.org/show_bug.cgi?id=9275
> Kernel: 2.6.23
> This is HP notebook nc6320 T2400 945GM

No response from developers

> 
> VIDEO DRIVERS========================================================
> 
> No text consoles with FRAMEBUFFER_CONSOLE_DETECT_PRIMARY
> http://bugzilla.kernel.org/show_bug.cgi?id=9310
> Kernel: 2.6.24-rc1
> This is a regression

No response from developers

> 
> PARALLEL PORT========================================================
> 
> LPC IT8705 POST port making noise on parallel port
> http://bugzilla.kernel.org/show_bug.cgi?id=9306
> Kernel: 2.6.16+
> 

No response from developers

> I/O STORAGE===========================================================
> 
> kernel bug from pktcdvd
> http://bugzilla.kernel.org/show_bug.cgi?id=9294
> Kernel: 2.6.23

I think we might have fixed this.

> After pci-e video card was installed, pci add-on usb card & firewire card fail
> http://bugzilla.kernel.org/show_bug.cgi?id=9223
> Kernel: 2.6.20 (testing of latest kernel requested)

No response from developers

> SCSI==================================================================
> 
> qla2xxx: driver initialization does not complete when booting with
> Port connected
> http://bugzilla.kernel.org/show_bug.cgi?id=9267
> Kernel: 2.6.23.1

No response from developers

> SOUND ALSA============================================================
> 
> Unable to load snd-hda-intel module: Unknown symbol in module, or
> unknown parameter
> http://bugzilla.kernel.org/show_bug.cgi?id=9242
> Kernel: 2.6.24-rc1

Takashi has responded

> usbaudio microphone: regular sound distortion on several Logitech Webcams
> http://bugzilla.kernel.org/show_bug.cgi?id=9230
> Kernel: 2.6.22.9

Clemens responded

> HID====================================================================
> 
> Kernel NULL pointer dereference at :usbhid:hiddev_ioctl+0x2f/0xabc
> http://bugzilla.kernel.org/show_bug.cgi?id=9216
> Kernel: 2.6.23.1
> Looks like this is a regression

No response from developers


So I count around seven reports which people are doing something with and
twenty seven which have been just ignored.

Three of these reports have been identified as regressions.  All three
of those remain unresponded to.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
@ 2007-11-13 11:24   ` Jens Axboe
  2007-11-13 11:33   ` Evgeniy Polyakov
                     ` (10 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Jens Axboe @ 2007-11-13 11:24 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Tue, Nov 13 2007, Andrew Morton wrote:
> > I/O STORAGE===========================================================
> > 
> > kernel bug from pktcdvd
> > http://bugzilla.kernel.org/show_bug.cgi?id=9294
> > Kernel: 2.6.23
> 
> I think we might have fixed this.

It's fixed and merged, I just forgot to close the bugzilla. Did so now.

-- 
Jens Axboe


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
  2007-11-13 11:24   ` Jens Axboe
@ 2007-11-13 11:33   ` Evgeniy Polyakov
  2007-11-13 11:39   ` David Miller
                     ` (9 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Evgeniy Polyakov @ 2007-11-13 11:33 UTC (permalink / raw)
  To: Andrew Morton; +Cc: Natalie Protasevich, linux-kernel, netdev

On Tue, Nov 13, 2007 at 03:15:53AM -0800, Andrew Morton (akpm@linux-foundation.org) wrote:
> > NETWORKING===========================================================
> > 
> > RTNLGRP_ND_USEROPT does not report ifindex (IPv6)
> > http://bugzilla.kernel.org/show_bug.cgi?id=9349
> > Kernel: 2.6.24+
> 
> No response from developers

Fixed (extended) in the DaveM's tree (or will be soon - patch was
submitted by Pierre Ynard).

Sorry, others are either driver related (and thus require
hardware to be tested on and maintainers to be kicked in) 
or too obscure (like 2.6.11 bug and weird network problem 
which is undetectible on other systems).

Yes, we suck, but we try to recover :)

-- 
	Evgeniy Polyakov

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
  2007-11-13 11:24   ` Jens Axboe
  2007-11-13 11:33   ` Evgeniy Polyakov
@ 2007-11-13 11:39   ` David Miller
  2007-11-13 11:49     ` Andrew Morton
  2007-11-13 11:47   ` Jarek Poplawski
                     ` (8 subsequent siblings)
  11 siblings, 1 reply; 268+ messages in thread
From: David Miller @ 2007-11-13 11:39 UTC (permalink / raw)
  To: akpm
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 13 Nov 2007 03:15:53 -0800

> > NETWORKING===========================================================
> > 
> > RTNLGRP_ND_USEROPT does not report ifindex (IPv6)
> > http://bugzilla.kernel.org/show_bug.cgi?id=9349
> > Kernel: 2.6.24+
> 
> No response from developers

That's funny, then how come there was a proper patch fix posted
and it's now in my tree ready to go to Linus?

I think you like just saying "No response from developers" over and
over again to make some of point about how developers are ignoring
lots of bugs.  That's fine, but at least be accurate about it :-)

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (2 preceding siblings ...)
  2007-11-13 11:39   ` David Miller
@ 2007-11-13 11:47   ` Jarek Poplawski
  2007-11-13 13:58   ` Mark Lord
                     ` (7 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Jarek Poplawski @ 2007-11-13 11:47 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On 13-11-2007 12:15, Andrew Morton wrote:
...
> Zero responses from developers
...
> No response from developers
...
> Andreas did some work, seemed to lose interest.
...
> Rafael poked Thomas a week ago, to no effect. Thomas has been travelling.

Looks like very reproducible!

Maybe you should add this to ...bugzilla?

Regards,
Jarek P.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:39   ` David Miller
@ 2007-11-13 11:49     ` Andrew Morton
  2007-11-13 11:58       ` David Miller
  0 siblings, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 11:49 UTC (permalink / raw)
  To: David Miller
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 03:39:46 -0800 (PST) David Miller <davem@davemloft.net> wrote:

> From: Andrew Morton <akpm@linux-foundation.org>
> Date: Tue, 13 Nov 2007 03:15:53 -0800
> 
> > > NETWORKING===========================================================
> > > 
> > > RTNLGRP_ND_USEROPT does not report ifindex (IPv6)
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9349
> > > Kernel: 2.6.24+
> > 
> > No response from developers
> 
> That's funny, then how come there was a proper patch fix posted
> and it's now in my tree ready to go to Linus?
> 
> I think you like just saying "No response from developers" over and
> over again to make some of point about how developers are ignoring
> lots of bugs.  That's fine, but at least be accurate about it :-)

Do you believe that our response to bug reports is adequate?

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:49     ` Andrew Morton
@ 2007-11-13 11:58       ` David Miller
  2007-11-13 12:12         ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: David Miller @ 2007-11-13 11:58 UTC (permalink / raw)
  To: akpm
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 13 Nov 2007 03:49:16 -0800

> Do you believe that our response to bug reports is adequate?

Do you feel that making us feel and look like shit helps?

I guess I'm just masterbating here all night long with the 46
bug fixes I've reviewed fully and queued up into my tree.  Along
with all the 10 or so -stable submissions I did tonight as well.

When someone like me is bug fixing full time, I take massive offense
to the impression you're trying to give especially when it's directed
at the networking.

So turn it down a notch Andrew.

I bet if you did things like list explicitly by name every single
person who adds a bug fix (however trivial) to an -mm release instead
of a new feature, you'll better achieve your goal than what you're
doing here.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:58       ` David Miller
@ 2007-11-13 12:12         ` Andrew Morton
  2007-11-13 12:32           ` David Miller
  2007-11-13 13:40           ` Ingo Molnar
  0 siblings, 2 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 12:12 UTC (permalink / raw)
  To: David Miller
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 03:58:24 -0800 (PST) David Miller <davem@davemloft.net> wrote:

> From: Andrew Morton <akpm@linux-foundation.org>
> Date: Tue, 13 Nov 2007 03:49:16 -0800
> 
> > Do you believe that our response to bug reports is adequate?
> 
> Do you feel that making us feel and look like shit helps?
> 

That doesn't answer my question.

See, first we need to work out whether we have a problem.  If we do this,
then we can then have a think about what to do about it.

I tried to convince the 2006 KS attendees that we have a problem and I
resoundingly failed.  People seemed to think that we're doing OK.

But it appears that data such as this contradicts that belief.


This is not a minor matter.  If the kernel _is_ slowly deteriorating then
this won't become readily apparent until it has been happening for a number
of years.  By that stage there will be so much work to do to get us back to
an acceptable level that it will take a huge effort.  And it will take a
long time after that for the kerel to get its reputation back.

So it is important that we catch deterioration *early* if it is happening.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 12:12         ` Andrew Morton
@ 2007-11-13 12:32           ` David Miller
  2007-11-13 19:02             ` Andrew Morton
  2007-11-13 19:32             ` [BUG] New Kernel Bugs Russell King
  2007-11-13 13:40           ` Ingo Molnar
  1 sibling, 2 replies; 268+ messages in thread
From: David Miller @ 2007-11-13 12:32 UTC (permalink / raw)
  To: akpm
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 13 Nov 2007 04:12:59 -0800

> On Tue, 13 Nov 2007 03:58:24 -0800 (PST) David Miller <davem@davemloft.net> wrote:
> 
> > From: Andrew Morton <akpm@linux-foundation.org>
> > Date: Tue, 13 Nov 2007 03:49:16 -0800
> > 
> > > Do you believe that our response to bug reports is adequate?
> > 
> > Do you feel that making us feel and look like shit helps?
> 
> That doesn't answer my question.
> 
> See, first we need to work out whether we have a problem.  If we do this,
> then we can then have a think about what to do about it.
> 
> I tried to convince the 2006 KS attendees that we have a problem and I
> resoundingly failed.  People seemed to think that we're doing OK.
> 
> But it appears that data such as this contradicts that belief.
> 
> This is not a minor matter.  If the kernel _is_ slowly deteriorating then
> this won't become readily apparent until it has been happening for a number
> of years.  By that stage there will be so much work to do to get us back to
> an acceptable level that it will take a huge effort.  And it will take a
> long time after that for the kerel to get its reputation back.
> 
> So it is important that we catch deterioration *early* if it is happening.

You tell me what I should spend my time working on, and I promise to
do it OK? :-)

For example, if I have a choice between a TCP crash just about anyone
can hit and some obscure issue only reported with some device nearly
nobody has, which one should I analyze and work on?

That's the problem.  All of us prioritize and it means the chaff
collects at the bottom.  You cannot fix that except by getting more
bug fixers so that the chaff pile has a chance to get smaller.

Luckily if the report being ignored isn't chaff, it will show up again
(and again and again) and this triggers a reprioritization because not
only is the bug no longer chaff, it also now got a lot of information
tagged to it so it's a double worthwhile investment to work on the
problem.

I think a lot of bugs that "aren't getting looked at" are simply
sitting in some early stage of this process.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 12:12         ` Andrew Morton
  2007-11-13 12:32           ` David Miller
@ 2007-11-13 13:40           ` Ingo Molnar
  2007-11-13 14:08             ` Mark Lord
  2007-11-13 16:55             ` Randy Dunlap
  1 sibling, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-13 13:40 UTC (permalink / raw)
  To: Andrew Morton
  Cc: David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon


* Andrew Morton <akpm@linux-foundation.org> wrote:

> > > Do you believe that our response to bug reports is adequate?
> > 
> > Do you feel that making us feel and look like shit helps?
> 
> That doesn't answer my question.
> 
> See, first we need to work out whether we have a problem.  If we do 
> this, then we can then have a think about what to do about it.
> 
> I tried to convince the 2006 KS attendees that we have a problem and I 
> resoundingly failed.  People seemed to think that we're doing OK.
> 
> But it appears that data such as this contradicts that belief.
> 
> This is not a minor matter.  If the kernel _is_ slowly deteriorating 
> then this won't become readily apparent until it has been happening 
> for a number of years.  By that stage there will be so much work to do 
> to get us back to an acceptable level that it will take a huge effort.  
> And it will take a long time after that for the kerel to get its 
> reputation back.
> 
> So it is important that we catch deterioration *early* if it is 
> happening.

yes, yes, yes, and i agree with you that there is a problem. I tried to 
make this point at the 2007 KS: not only is degradation in quality not 
apparent for years, slow degradation in quality can give kernel 
developers the exact _opposite_ perception! (Fewer testers means fewer 
bugreports and that results in apparent "improved" quality and fewer 
reported regressions - while exactly the opposite is happening and 
testers are leaving us without giving us any indication that this is 
happening. We just dont notice.)

I'm not moaning about bugs that slip through - those are unavoidable 
facts of a high flux codebase. I'm moaning about reoccuring, avoidable 
bugs, i'm moaning about hostility towards testers, i'm moaning about 
hostility towards automated testing, i'm moaning about unnecessary hoops 
a willing (but unskilled) tester has to go through to help us out.

I tried to make the point that the only good approach is to remove our 
current subjective bias from quality metrics and to at least realize 
what a cavalier attitude we still have to QA. The moment we are able to 
_measure_ how bad we are, kernel developers will adopt in a second and 
will improve those metrics. Lets use more debug tools, both static and 
dynamic ones. Lets measure tester base and we need to measure _lost_ 
early adopters and the reasons why they are lost. Regression metrics are 
a very important first step too and i'm very happy about the increasing 
effort that is being spent on this.

This is all QA-101 that _cannot be argued against on a rational basis_, 
it's just that these sorts of things have been largely ignored for 
years, in favor of the all-too-easy "open source means many eyeballs and 
that is our QA" answer, which is a _good_ answer but by far not the most 
intelligent answer! Today "many eyeballs" is simply not good enough and 
nature (and other OS projects) will route us around if we dont change.

We kernel developers have been spoiled by years of abundance in testing 
resources. We squander tons of resources in this area, and we could be 
so much more economic about this without hindering our development model 
in any way. We could be so much better about QA and everyone would 
benefit without having to compromize on the incoming flux of changes - 
it's so much easier to write new features for a high quality kernel.

My current guesstimation is that we are utilizing our current testing 
resources at around 10% efficiency. (i.e. if we did an 'ideal' job we 
could fix 10 times as many bugs with the same size of tester effort!) It 
used to be around 5%. (and i mainly attribute the increase from 5% to 
10% to Andrew and the many other people who do kernel QA - kudos!) 10% 
is still awful and we very much suck.

Paradoxically, the "end product" is still considerably good quality in 
absolute terms because other pieces of our infrastructure are so good 
and powerful, but QA is still a 'weak link' of our path to the user that 
reduces the quality of the end result. We could _really_ be so much 
better without any compromises that hurt.

(and this is in no way directed at the networking folks - it holds for 
all of us. I have one main complaint about networking: the separate 
netdev list is a bad idea - networking regressions should be discussed 
and fixed on lkml, like most other subsystems are. Any artificial split 
of the lk discussion space is bad.)

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (3 preceding siblings ...)
  2007-11-13 11:47   ` Jarek Poplawski
@ 2007-11-13 13:58   ` Mark Lord
  2007-11-13 14:18     ` Mark Lord
  2007-11-13 16:07     ` Thomas Gleixner
  2007-11-13 15:21   ` Bartlomiej Zolnierkiewicz
                     ` (6 subsequent siblings)
  11 siblings, 2 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 13:58 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

Andrew Morton wrote:
> On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich" <protasnb@gmail.com> wrote:
..
>> with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
>> boot (ARM, Timer)
>> http://bugzilla.kernel.org/show_bug.cgi?id=9229
>> Kernel: 2.6.23
> 
> No response from developers
..

Note:  that same bug exists/existed on i386 back when NO_HZ was
introduced (2.6.21?).  I still see it from time to time on my Quad core
system (very rare), but not any more on my Duo notebook where it used
to happen about 1 in n boots (n < 10).

AFAICT no fix was ever released for it.



>> Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
>> http://bugzilla.kernel.org/show_bug.cgi?id=9275
>> Kernel: 2.6.23
>> This is HP notebook nc6320 T2400 945GM
> No response from developers
..

I *still* get very slow resume-from-RAM quite often here
(new in 2.6.22 kernel, wasn't there in early 2.6.23-rc*).
Something eventually times out after a minute or so
and it comes back.  Cannot make it happen reliably,
unless I'm in a hurry to get something done.  :)
I suspect USB here, probably the same loopy bug that
we added a "loop limit failsafe" for back in 2.6.21(?).

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 13:40           ` Ingo Molnar
@ 2007-11-13 14:08             ` Mark Lord
  2007-11-13 15:24               ` Giacomo A. Catenazzi
                                 ` (4 more replies)
  2007-11-13 16:55             ` Randy Dunlap
  1 sibling, 5 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 14:08 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Ingo Molnar wrote:
..
> This is all QA-101 that _cannot be argued against on a rational basis_, 
> it's just that these sorts of things have been largely ignored for 
> years, in favor of the all-too-easy "open source means many eyeballs and 
> that is our QA" answer, which is a _good_ answer but by far not the most 
> intelligent answer! Today "many eyeballs" is simply not good enough and 
> nature (and other OS projects) will route us around if we dont change.
..

QA-101 and "many eyeballs" are not at all in opposition.
The latter is how we find out about bugs on uncommon hardware,
and the former is what we need to track them and overall quality.

A HUGE problem I have with current "efforts", is that once someone
reports a bug, the onus seems to be 99% on the *reporter* to find
the exact line of code or commit.  Ghad what a repressive method.

And if the "developer" who broke the damn thing, or who at least
"claims" to be supporting that code, cannot "reproduce" the bug,
they drop it completely.

Contrast that flawed approach with how Linus does things..
he thinks through the symptoms, matches them to the code,
and figures out what the few possibilities might be,
and feeds back some trial balloon patches for the bug reporter to try.

MUCH better. 

Linus also asks for a git bisect, but doesn't insist upon the reporter
learning an entire new (poorly documented) toolset just to to report a bug.

Blah!

And remember, *I'm* an old-time Linux kernel developer.. just think about
the people reporting bugs who haven't been around here since 1992..

-ml

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 13:58   ` Mark Lord
@ 2007-11-13 14:18     ` Mark Lord
  2007-11-13 16:08       ` Thomas Gleixner
  2007-11-13 16:07     ` Thomas Gleixner
  1 sibling, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 14:18 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

Mark Lord wrote:
> Andrew Morton wrote:
>> On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich" 
>> <protasnb@gmail.com> wrote:
> ..
..
>>> Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
>>> http://bugzilla.kernel.org/show_bug.cgi?id=9275
>>> Kernel: 2.6.23
>>> This is HP notebook nc6320 T2400 945GM
>> No response from developers
> ..
> 
> I *still* get very slow resume-from-RAM quite often here
> (new in 2.6.22 kernel, wasn't there in early 2.6.23-rc*).
..

Typo.  That should have said:

> (new in 2.6.23 kernel, wasn't there in early 2.6.23-rc*).

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (4 preceding siblings ...)
  2007-11-13 13:58   ` Mark Lord
@ 2007-11-13 15:21   ` Bartlomiej Zolnierkiewicz
  2007-11-13 15:33   ` James Bottomley
                     ` (5 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Bartlomiej Zolnierkiewicz @ 2007-11-13 15:21 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Nov 13, 2007 12:15 PM, Andrew Morton <akpm@linux-foundation.org> wrote:
> On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich" <protasnb@gmail.com> wrote:
>
> > This is the listing of the open bugs that are relatively new, around
> > 2.6.22 and up. They are vaguely classified by specific area.
> > (not a full list, there are more :)

[...]

> > IDE/SATA=========================================================

[...]

> > DVD-RAM umount and disk free bug
> > http://bugzilla.kernel.org/show_bug.cgi?id=9265
> > Kernel: 2.6.15  (asked to try current kernel)
>
> No response from developers

Bug was filled under IO/Storage-Other so is it assigned to
<other_other@kernel-bugs.osdl.org>.

Could be a FS problem as well but it is the best to wait for
confirmation with 2.6.23 before proceeding further...

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:08             ` Mark Lord
@ 2007-11-13 15:24               ` Giacomo A. Catenazzi
  2007-11-13 15:57                 ` Ray Lee
  2007-11-13 15:52               ` Benoit Boissinot
                                 ` (3 subsequent siblings)
  4 siblings, 1 reply; 268+ messages in thread
From: Giacomo A. Catenazzi @ 2007-11-13 15:24 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Mark Lord wrote:
> Ingo Molnar wrote:
> ..
>> This is all QA-101 that _cannot be argued against on a rational 
>> basis_, it's just that these sorts of things have been largely ignored 
>> for years, in favor of the all-too-easy "open source means many 
>> eyeballs and that is our QA" answer, which is a _good_ answer but by 
>> far not the most intelligent answer! Today "many eyeballs" is simply 
>> not good enough and nature (and other OS projects) will route us 
>> around if we dont change.
> ..
> 
> QA-101 and "many eyeballs" are not at all in opposition.
> The latter is how we find out about bugs on uncommon hardware,
> and the former is what we need to track them and overall quality.
> 
> A HUGE problem I have with current "efforts", is that once someone
> reports a bug, the onus seems to be 99% on the *reporter* to find
> the exact line of code or commit.  Ghad what a repressive method.


As a long time kernel tester, I see some problem with the
newer "new development model". In the short merge windows,
after to much time, there are to many patches.
So there are problem to bisect bugs, and to have attention
of developers. My impression is that in a week there are
many more messages in lkml and to much bugs to be
handled in these few days.

I've two proposal:

- better patch quality. I would like that every commit
would compile. So an automatic commit test and public
blames could increase the quality of first commits.
[bisecting with non compilable point it is not a trivial
task]

- a slow down the patch inclusion on the merge windows
(aka: not to much big changes in the first days).
As tester I prefer that some big changes would be
included in a "secondary window" (pre o rc release),
in an other period as the big patch rush.

ciao
	cate

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (5 preceding siblings ...)
  2007-11-13 15:21   ` Bartlomiej Zolnierkiewicz
@ 2007-11-13 15:33   ` James Bottomley
  2007-11-13 16:43     ` Randy Dunlap
  2007-11-13 17:46     ` Martin Bligh
  2007-11-13 15:36   ` Alan Cox
                     ` (4 subsequent siblings)
  11 siblings, 2 replies; 268+ messages in thread
From: James Bottomley @ 2007-11-13 15:33 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon, linux-scsi

On Tue, 2007-11-13 at 03:15 -0800, Andrew Morton wrote:
> >
> SCSI==================================================================
> > 
> > qla2xxx: driver initialization does not complete when booting with
> > Port connected
> > http://bugzilla.kernel.org/show_bug.cgi?id=9267
> > Kernel: 2.6.23.1
> 
> No response from developers

Urm, well, if no-one ever tells the SCSI list it's unrealistic to expect
anyone to be working on it.  As far as I can tell, email was sent to
Andrew Vasquez only on 31 October. However, the fault looks to be
generic, so he probably just dropped it.

This seems to be the significant line from the trace:

Oct  7 23:35:07 t-host kernel:   ISP2422: PCI-X Mode 1 (133 MHz) @
0000:01:03.0
hdma-, host#=1, fw=4.00.27 [IP] 
Oct  7 23:35:07 t-host kernel: ACPI: PCI Interrupt 0000:01:03.1[B] -> GSI 29
(level, low) -> IRQ 22
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Found an ISP2422, irq 22,
iobase 0xf8cf4000
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Configuring PCI space...
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Configure NVRAM
parameters...
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Verifying loaded RISC
code...
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Allocated (64 KB) for
EFT...
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: Allocated (1413 KB) for
firmware dump...
Oct  7 23:35:07 t-host kernel: scsi2 : qla2xxx
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.1: 
Oct  7 23:35:07 t-host kernel:  QLogic Fibre Channel HBA Driver: 8.01.07-k7
Oct  7 23:35:07 t-host kernel:   QLogic QLA2462 - PCI-X 2.0 to 4Gb FC, Dual
Channel
Oct  7 23:35:07 t-host kernel:   ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:01:03.1
hdma-, host#=2, fw=4.00.27 [IP] 
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.0: LIP reset occured (f8f7).
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.0: LIP occured (f8f7).
Oct  7 23:35:07 t-host kernel: qla2xxx 0000:01:03.0: LOOP UP detected (4 Gbps).
Oct  7 23:35:07 t-host kernel: ohci_hcd 0000:03:00.0: auto-stop root hub
Oct  7 23:35:07 t-host kernel: ohci_hcd 0000:03:00.1: auto-stop root hub
Oct  7 23:35:07 t-host kernel: scsi 1:0:0:0: Direct-Access     transtec
PV610F16R1C      348B PQ: 0 ANSI: 4
Oct  7 23:35:07 t-host kernel: kobject_add failed for 1:0:0:0 with -EEXIST,
don't try to register things with the same name in the same directory.
Oct  7 23:35:07 t-host kernel:  [<c022c841>] kobject_shadow_add+0x111/0x190
Oct  7 23:35:07 t-host kernel:  [<c0286814>] device_add+0xc4/0x570
Oct  7 23:35:07 t-host kernel:  [<c02c90ce>] scsi_adjust_queue_depth+0x9e/0xf0
Oct  7 23:35:07 t-host kernel:  [<c02249b2>] __blk_queue_init_tags+0x32/0x70
Oct  7 23:35:07 t-host kernel:  [<c02d302f>] scsi_sysfs_add_sdev+0x4f/0x230
Oct  7 23:35:07 t-host kernel:  [<f8d93421>] qla2xxx_slave_configure+0x71/0x100
[qla2xxx]
Oct  7 23:35:07 t-host kernel:  [<c02d0ecf>] scsi_probe_and_add_lun+0xa5f/0xb40
Oct  7 23:35:07 t-host kernel:  [<c02d1559>] __scsi_scan_target+0xd9/0x6c0
Oct  7 23:35:07 t-host kernel:  [<c03a5be1>] schedule+0x2e1/0x950
Oct  7 23:35:07 t-host kernel:  [<c02d21f9>] scsi_scan_target+0xa9/0xe0
Oct  7 23:35:07 t-host kernel:  [<c02d5640>] fc_scsi_scan_rport+0x0/0x80
Oct  7 23:35:07 t-host kernel:  [<c02d56a9>] fc_scsi_scan_rport+0x69/0x80
Oct  7 23:35:07 t-host kernel:  [<c012b032>] run_workqueue+0x72/0x100
Oct  7 23:35:07 t-host kernel:  [<c012e8d0>] prepare_to_wait+0x20/0x70
Oct  7 23:35:07 t-host kernel:  [<c012b8c0>] worker_thread+0x0/0x100
Oct  7 23:35:07 t-host kernel:  [<c012b964>] worker_thread+0xa4/0x100
Oct  7 23:35:07 t-host kernel:  [<c012e720>] autoremove_wake_function+0x0/0x50
Oct  7 23:35:07 t-host kernel:  [<c012b8c0>] worker_thread+0x0/0x100
Oct  7 23:35:07 t-host kernel:  [<c012e462>] kthread+0x42/0x70
Oct  7 23:35:07 t-host kernel:  [<c012e420>] kthread+0x0/0x70
Oct  7 23:35:07 t-host kernel:  [<c0103573>] kernel_thread_helper+0x7/0x14
Oct  7 23:35:07 t-host kernel:  =======================
Oct  7 23:35:07 t-host kernel: error 1

It looks like some type of sysfs/kobject race in SCSI ... and I think we
might have seen it before, just not able to reproduce it reliably.

My bet would be that the LIP which acts like a reset and occurs in the
middle of the scan and so the initialising object is killed on the first
scan but not yet dead and then can't be re-added on the second scan.

Hannes has patches to help with this, but they're rather complex, and
not really 2.6.24 material.  I could see if there's a simpler fix.

James



^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (6 preceding siblings ...)
  2007-11-13 15:33   ` James Bottomley
@ 2007-11-13 15:36   ` Alan Cox
  2007-11-13 17:49   ` Jan Kara
                     ` (3 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Alan Cox @ 2007-11-13 15:36 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

> > pata_pdc202xx_old excessive ATA bus errors
> > http://bugzilla.kernel.org/show_bug.cgi?id=9337
> > 2.6.24-rc2
> 
> No response from developers

Untrue. We've been discussing it on list in the past and its now on
bugzilla. Not obvious from outside I realise. That one I'm afraid is
probably a longer term item.

> > DVD-RAM umount and disk free bug
> > http://bugzilla.kernel.org/show_bug.cgi?id=9265
> > Kernel: 2.6.15  (asked to try current kernel)
> 
> No response from developers

Not actually sure who is looking after this now ?

> > LPC IT8705 POST port making noise on parallel port
> > http://bugzilla.kernel.org/show_bug.cgi?id=9306
> > Kernel: 2.6.16+
> > 
> 
> No response from developers

Not sure who really owns parallel. Have grabbed and will sort
out.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:08             ` Mark Lord
  2007-11-13 15:24               ` Giacomo A. Catenazzi
@ 2007-11-13 15:52               ` Benoit Boissinot
  2007-11-13 16:49                 ` Ingo Molnar
  2007-11-13 17:13                 ` Theodore Tso
  2007-11-13 16:46               ` Ingo Molnar
                                 ` (2 subsequent siblings)
  4 siblings, 2 replies; 268+ messages in thread
From: Benoit Boissinot @ 2007-11-13 15:52 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Nov 13, 2007 3:08 PM, Mark Lord <liml@rtr.ca> wrote:
>
> Ingo Molnar wrote:
> ..
> > This is all QA-101 that _cannot be argued against on a rational basis_,
> > it's just that these sorts of things have been largely ignored for
> > years, in favor of the all-too-easy "open source means many eyeballs and
> > that is our QA" answer, which is a _good_ answer but by far not the most
> > intelligent answer! Today "many eyeballs" is simply not good enough and
> > nature (and other OS projects) will route us around if we dont change.
> ..
>
> QA-101 and "many eyeballs" are not at all in opposition.
> The latter is how we find out about bugs on uncommon hardware,
> and the former is what we need to track them and overall quality.
>
> A HUGE problem I have with current "efforts", is that once someone
> reports a bug, the onus seems to be 99% on the *reporter* to find
> the exact line of code or commit.  Ghad what a repressive method.
>

Btw, I used to test every -mm kernel. But since I've switched distros
(gentoo->ubuntu)
and I have less time, I feel it's harder to test -rc or -mm kernels (I
know this isn't a lkml problem
but more a distro problem, but I would love having an ubuntu blessed
repo with current dev kernel
for the latest stable ubuntu release).

For debugging, maybe it's time someone does an amazon ec2+s3 service
to automate the bisecting
and create .deb/.rpm from git, I don't know how much it would cost though.

regards,

Benoit

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:24               ` Giacomo A. Catenazzi
@ 2007-11-13 15:57                 ` Ray Lee
  2007-11-13 17:01                   ` Adrian Bunk
  0 siblings, 1 reply; 268+ messages in thread
From: Ray Lee @ 2007-11-13 15:57 UTC (permalink / raw)
  To: Giacomo A. Catenazzi
  Cc: Mark Lord, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

On Nov 13, 2007 7:24 AM, Giacomo A. Catenazzi <cate@cateee.net> wrote:
> As a long time kernel tester, I see some problem with the
> newer "new development model". In the short merge windows,
> after to much time, there are to many patches.

I think the root issue there is that it's hard to get all testers to
run a bisect, but easy to ask them to test snapshots. Right now the
snapshots are generated nightly, but I think it would make more sense
if they were generated every N patches, for some value of N...

Of course, for that to really work, we have to ensure that the result
is always compilable, which has been getting better, but not perfect.

Ray

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 13:58   ` Mark Lord
  2007-11-13 14:18     ` Mark Lord
@ 2007-11-13 16:07     ` Thomas Gleixner
  2007-11-13 17:47       ` Mark Lord
                         ` (2 more replies)
  1 sibling, 3 replies; 268+ messages in thread
From: Thomas Gleixner @ 2007-11-13 16:07 UTC (permalink / raw)
  To: Mark Lord
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007, Mark Lord wrote:

> Andrew Morton wrote:
> > On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
> > <protasnb@gmail.com> wrote:
> ..
> > > with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
> > > boot (ARM, Timer)
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9229
> > > Kernel: 2.6.23
> > 
> > No response from developers
> ..

The bug report is bogus. ARM has no CONFIG_HPET_TIMER. 
 
> Note:  that same bug exists/existed on i386 back when NO_HZ was
> introduced (2.6.21?).  I still see it from time to time on my Quad core
> system (very rare), but not any more on my Duo notebook where it used
> to happen about 1 in n boots (n < 10).
> 
> AFAICT no fix was ever released for it.

Hmm, at which point does the boot stop ? 

> > > Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9275
> > > Kernel: 2.6.23
> > > This is HP notebook nc6320 T2400 945GM
> > No response from developers
> ..
> 
> I *still* get very slow resume-from-RAM quite often here
> (new in 2.6.22 kernel, wasn't there in early 2.6.23-rc*).

Hmm. Which one 22 or 23 ?

> Something eventually times out after a minute or so
> and it comes back.  Cannot make it happen reliably,
> unless I'm in a hurry to get something done.  :)
> I suspect USB here, probably the same loopy bug that
> we added a "loop limit failsafe" for back in 2.6.21(?).

Do you have a pointer to that please ?

Thanks,

	tglx

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:18     ` Mark Lord
@ 2007-11-13 16:08       ` Thomas Gleixner
  0 siblings, 0 replies; 268+ messages in thread
From: Thomas Gleixner @ 2007-11-13 16:08 UTC (permalink / raw)
  To: Mark Lord
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007, Mark Lord wrote:

> Mark Lord wrote:
> > Andrew Morton wrote:
> > > On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
> > > <protasnb@gmail.com> wrote:
> > ..
> ..
> > > > Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> > > > http://bugzilla.kernel.org/show_bug.cgi?id=9275
> > > > Kernel: 2.6.23
> > > > This is HP notebook nc6320 T2400 945GM
> > > No response from developers
> > ..
> > 
> > I *still* get very slow resume-from-RAM quite often here
> > (new in 2.6.22 kernel, wasn't there in early 2.6.23-rc*).
> ..
> 
> Typo.  That should have said:
> 
> > (new in 2.6.23 kernel, wasn't there in early 2.6.23-rc*).

Just asked that :) Is there a chance to bisect that ?

Thanks,

	tglx

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:33   ` James Bottomley
@ 2007-11-13 16:43     ` Randy Dunlap
  2007-11-13 17:46     ` Martin Bligh
  1 sibling, 0 replies; 268+ messages in thread
From: Randy Dunlap @ 2007-11-13 16:43 UTC (permalink / raw)
  To: James Bottomley, mbligh
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon,
	linux-scsi

On Tue, 13 Nov 2007 09:33:21 -0600 James Bottomley wrote:

> On Tue, 2007-11-13 at 03:15 -0800, Andrew Morton wrote:
> > >
> > SCSI==================================================================
> > > 
> > > qla2xxx: driver initialization does not complete when booting with
> > > Port connected
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9267
> > > Kernel: 2.6.23.1
> > 
> > No response from developers
> 
> Urm, well, if no-one ever tells the SCSI list it's unrealistic to expect
> anyone to be working on it.  As far as I can tell, email was sent to
> Andrew Vasquez only on 31 October. However, the fault looks to be
> generic, so he probably just dropped it.

It seems that new SCSI bugs need to be sent to linux-scsi@vger.kernel.org.

Martin, can you arrange that to happen automatically instead of
Andrew having to do it manually?

---
~Randy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:08             ` Mark Lord
  2007-11-13 15:24               ` Giacomo A. Catenazzi
  2007-11-13 15:52               ` Benoit Boissinot
@ 2007-11-13 16:46               ` Ingo Molnar
  2007-11-13 17:50                 ` Mark Lord
  2007-11-13 19:37               ` [BUG] New Kernel Bugs Russell King
  2007-11-14  0:34               ` Denys Vlasenko
  4 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-13 16:46 UTC (permalink / raw)
  To: Mark Lord
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


* Mark Lord <liml@rtr.ca> wrote:

> Ingo Molnar wrote:
> ..
>> This is all QA-101 that _cannot be argued against on a rational basis_, 
>> it's just that these sorts of things have been largely ignored for years, 
>> in favor of the all-too-easy "open source means many eyeballs and that is 
>> our QA" answer, which is a _good_ answer but by far not the most 
>> intelligent answer! Today "many eyeballs" is simply not good enough and 
>> nature (and other OS projects) will route us around if we dont change.
> ..
>
> QA-101 and "many eyeballs" are not at all in opposition.

yes, absolutely so - that's why i used the "good" qualifier. "Good is 
not good enough" calls for additional efforts to make it more efficient, 
not for the abolition of the many eyeballs concept (which would be 
absurd). So what i wanted to say is that _sole_ reliance on the large 
numbers of eyeballs is a fundamental mistake. It's even sometimes used 
as an excuse to merge questionable stuff. "we'll find any bugs, many 
eyeballs will make bugs shallow". In reality the many eyeballs are not 
infinite, nor should they be taken for granted if they are used for 
bogus things. We have to make sure the eyeballs stay 'many', and we also 
have to make sure they are not wasted. It's a physical resource that 
must be intelligently handled. Its positive effects can be easily wasted 
and we do that today.

for example git-bisect was godsent. I remember that years ago bisection 
of a bug was a very laborous task so that it was only used as a final, 
last-ditch approach for really nasty bugs. Today we can autonomouly 
bisect build bugs via a simple shell command around "git-bisect run", 
without any human interaction! This freed up testing resources 
enormously and made bisection one of the _first_ things that are tried 
when bugs are met. We just need more of this (distros should offer 
pre-built kernel rpm 'farms' for every important commit point and 
automated tools for users to easily specify breakage points, without 
them having to install those kernels individually) , and everyone should 
be aware of the fact that we still suck (we merge too much crap and 
still dont have good enough tools to de-crappify what we merge) and that 
we are losing testers.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:52               ` Benoit Boissinot
@ 2007-11-13 16:49                 ` Ingo Molnar
  2007-11-13 17:13                 ` Theodore Tso
  1 sibling, 0 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-13 16:49 UTC (permalink / raw)
  To: Benoit Boissinot
  Cc: Mark Lord, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon


* Benoit Boissinot <bboissin@gmail.com> wrote:

> For debugging, maybe it's time someone does an amazon ec2+s3 service 
> to automate the bisecting and create .deb/.rpm from git, I don't know 
> how much it would cost though.

a few months ago i estimated the costs of this and it's just a few 
terabytes so within arm's reach. As long as the .deb/.rpm's are built by 
tracking -git in a rolling fashion CPU time should not be a big issue. 
The only limit is download bandwidth - but even that problem might be 
solvable via a huge git repository of ready-to-boot .o's that are linked 
together on the tester's machine.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 13:40           ` Ingo Molnar
  2007-11-13 14:08             ` Mark Lord
@ 2007-11-13 16:55             ` Randy Dunlap
  2007-11-14 14:08               ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Randy Dunlap @ 2007-11-13 16:55 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 14:40:29 +0100 Ingo Molnar wrote:

> 
> * Andrew Morton <akpm@linux-foundation.org> wrote:
> 
> > > > Do you believe that our response to bug reports is adequate?
> > > 
> > > Do you feel that making us feel and look like shit helps?
> > 
> > That doesn't answer my question.
> > 
> > See, first we need to work out whether we have a problem.  If we do 
> > this, then we can then have a think about what to do about it.
> > 
> > I tried to convince the 2006 KS attendees that we have a problem and I 
> > resoundingly failed.  People seemed to think that we're doing OK.

We were a minority.

> > But it appears that data such as this contradicts that belief.
> > 
> > This is not a minor matter.  If the kernel _is_ slowly deteriorating 
> > then this won't become readily apparent until it has been happening 
> > for a number of years.  By that stage there will be so much work to do 
> > to get us back to an acceptable level that it will take a huge effort.  
> > And it will take a long time after that for the kerel to get its 
> > reputation back.
> > 
> > So it is important that we catch deterioration *early* if it is 
> > happening.
> 

[agree with most of Ingo's moaning]

> (and this is in no way directed at the networking folks - it holds for 
> all of us. I have one main complaint about networking: the separate 
> netdev list is a bad idea - networking regressions should be discussed 
> and fixed on lkml, like most other subsystems are. Any artificial split 
> of the lk discussion space is bad.)

but here I disagree.  LKML is already too busy and noisy.
Major subsystems need their own discussion areas.

---
~Randy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:04                 ` Andrew Morton
@ 2007-11-13 16:56                   ` Nick Piggin
  2007-11-14 19:54                     ` Linus Torvalds
  2007-11-13 21:37                   ` Adrian Bunk
  2007-11-13 21:56                   ` Christian Kujau
  2 siblings, 1 reply; 268+ messages in thread
From: Nick Piggin @ 2007-11-13 16:56 UTC (permalink / raw)
  To: Andrew Morton; +Cc: Christian Kujau, linux-kernel, torvalds

rant on :) ... These aren't directed specifically at Andrew, but
everyone who merges patches or is involved in the release process.

On Wednesday 14 November 2007 08:04, Andrew Morton wrote:
> On Tue, 13 Nov 2007 21:00:30 +0100 (CET) Christian Kujau 
<lists@nerdbynature.de> wrote:
> > On Tue, 13 Nov 2007, Andrew Morton wrote:
> > > I think that we're fairly good about working the regressions in
> > > Adrian/Michal/Rafael's lists but once Linus releases 2.6.x we tend to
> > > let the unsolved ones slide, and we don't pay as much attention to the
> > > regressions which 2.6.x testers report.
> >
> > Can't we wait until all regressions[0] are fixed before releasing a new
> > 2.6.x? I'd consider regressions a *literal* show stopper, and with this
> > policy they just have be fixed, nothing would "slide"...
>
> Problem is that everyone would then sit around pumping shiny new features
> into their trees waiting until someone else fixes the regressions.

Not if you said their regression causing patches will get reverted unless it
can be fixed for release. For everyone not involved, they'll be doing their
own productive things and we don't want to stop that.


> There are a number of process things we _could_ do.  Like
>
> - have bugfix-only kernel releases

I don't know why this would be better than the above. If you are worried
about perception of released kernels, then it would actually be worse,
because the non-bugfix-only releases will get out there, and the numbering
scheme gets yet another level of complexity.

Make 2.6.24-rc3 your bugfix only release. If you argue that would make
the cycle too long, the solution is to merge less stuff in 2.6.24-rc1.


> - Just refuse to merge any non-bugfix patches for a subsystem when it is
>   determined that the subsystem has "too many" regressions.

If you don't allow regressions to build up over releases in the first
place, then this naturally gets done for you.


> - Create an "if you added a regression, you should fix some other bug
>   too" rule.

That's pretty annoying. Everybody tries not to introduce regressions.
It's just a natural part of development. You just have to make the
system work well within that constraint.

It's easy: "if you add a regression, you fix it. If it doesn't get fixed,
we either don't release or we revert your patch."

That takes care of regressions. Now for actually improving quality. I
think to do that you have to encourage code review and bug fixing.

- Take reviewers seriously, and don't allow patches to be merged if they
  have outstanding unaddressed comments (unaddressed doesn't have to mean 
  changed completely to reviewers taste, but at least answered questions
  and provided rationale). Don't merge unreviewed patches.

- Prioritise bugfixes and regression fixes. I realise they can be
  very complex changes, but I am disappointed sometimes at how some
  of my bugfix attempts are received. Things like silent and
  un-reproduceable pagecache corruption, memory ordering bugs which
  will likewise cause silent and un-reproduceable data corruption
  are totally unacceptable IMO; worse than most simple (eg. fail-stop,
  performance) regressions. To see them struggle because the patch
  isn't perfect right off the bat, they're deemed too hard, or they
  clash with some pending "feature" is a pity to me. I don't expect
  thanks or even help, but at least having some priority would help
  me stay interested and the bug to get fixed quicker.

  For a concrete example: when I did the remap_vmalloc_range() patch,
  I converted over all in-tree drivers to use the range checking and
  much safer remap_vmalloc_range. During this conversion I found
  several places where drivers were potentially inserting mappings
  wrongly or not checking user inputs properly (eg. corruption and/or
  security issues). And tried to fix them. And yet the whole patchset
  was dropped, despite being simpler and cleaner code, and attempting
  to fix bugs. Because I wasn't able to test the hardware (and/or
  maintainers didn't respond). It didn't even get a chance in -mm
  (and if it had, it probably would have been immediately dropped if
  I had a typo somewhere). Those patches are still rotting on my hdd
  somewhere... So it is actually far easier for me to shut my eyes and
  not bother reviewing any in-tree code when introducing a new API or
  something like that.
  
  And yet something like CFS basically bypasses the review and test
  process entirely and gets upstream at least a release too soon. That
  isn't anything against the technical side of CFS development, which
  I'm a lot happier with than the old scheduler. It is a problem with
  the merging and release process.

- "if you added a regression, you should fix some other bug too" rule
  should be "if you want to add a new feature, you should review a
  number of other patches". Review points can be traded. If this could
  be done right, it would create a direct economic incentive to review.

OK, the last one is my pipedream that will never happen ;) But you
should understand what can be achieved, what can't, and what will be
the most productive way to change the system.


> - probably other stuff.
>
> But we can't/shouldn't do any of that until it is generally agreed that we
> have a problem and that the problem is of sufficient magnitude that process
> changes are needed to address it.  We aren't at that stage yet.


Well I don't think I need to agree that the kernel is getting worse in
order to think there are ways we can change the system to help it get
better. We can make changes for the better without making things more
difficult for anybody, IMO.

But is the kernel getting worse? I wonder if it has anything to do with
getting further away from large distros? (and thus will get better again
during the next distro release cycle). Because I know SLES9 took a huge
amount of work to get stable. Or do you think it is getting worse since
2.6.0?


> Here's an important point: developers have a fixed amount of development
> time.  They spend some of that time fixing bugs and the rest of that time
> on <otherstuff>.  And while one could cook up all sorts of wonderful
> process changes, they all would be aimed at a single thing: shifting some
> of the developers' time away from <otherstuff> and onto bugfixing.
>
> At this stage the only tool which is being deployed to attempt to bring
> about that reprioritisation is suasion.  aka "lkml flamewar".

To summarise, I think don't actually worry about how the developers
spend their time. All you have to do is control what patches you take
and release policy. Improve the system so it tolerates regressions and
poor quality code (which are inevitable).

Review bandwidth and regression fix rate should just naturally throttle
new features / code going in. And you encourage people to do good things
rather than hit them when inevitable bad things happen.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:57                 ` Ray Lee
@ 2007-11-13 17:01                   ` Adrian Bunk
  2007-11-13 17:50                     ` Romano Giannetti
  0 siblings, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 17:01 UTC (permalink / raw)
  To: Ray Lee
  Cc: Giacomo A. Catenazzi, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, Nov 13, 2007 at 07:57:54AM -0800, Ray Lee wrote:
> On Nov 13, 2007 7:24 AM, Giacomo A. Catenazzi <cate@cateee.net> wrote:
> > As a long time kernel tester, I see some problem with the
> > newer "new development model". In the short merge windows,
> > after to much time, there are to many patches.
> 
> I think the root issue there is that it's hard to get all testers to
> run a bisect, but easy to ask them to test snapshots. Right now the
> snapshots are generated nightly, but I think it would make more sense
> if they were generated every N patches, for some value of N...
>...

I don't see a point in doing that - that would be a more manual 
bisecting, and the result would not be one guilty commit.

Testers are not expected to be able to hack a kernel, but it's 
reasonable to expect testers to be able to build their own kernels
(and your proposal wouldn't change that).

The small instruction below is enough for everyone who is able to 
build his own kernel to do a git bisect.

> Ray

cu
Adrian


<--  snip  -->


# install git

# clone Linus' tree:
git clone \ 
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git

# start bisecting:
cd linux-2.6
git bisect start
git bisect bad v2.6.21
git bisect good v2.6.20
cp /path/to/.config .

# start a round
make oldconfig
make
# install kernel, check whether it's good or bad, then:
git bisect [bad|good]
# start next round


After at about 10-15 reboots you'll have found the guilty commit
("...  is first bad commit").


More information on git bisecting:
  man git-bisect


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:52               ` Benoit Boissinot
  2007-11-13 16:49                 ` Ingo Molnar
@ 2007-11-13 17:13                 ` Theodore Tso
  2007-11-13 17:30                   ` Alan Cox
                                     ` (3 more replies)
  1 sibling, 4 replies; 268+ messages in thread
From: Theodore Tso @ 2007-11-13 17:13 UTC (permalink / raw)
  To: Benoit Boissinot
  Cc: Mark Lord, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
> Btw, I used to test every -mm kernel. But since I've switched distros
> (gentoo->ubuntu)
> and I have less time, I feel it's harder to test -rc or -mm kernels (I
> know this isn't a lkml problem
> but more a distro problem, but I would love having an ubuntu blessed
> repo with current dev kernel
> for the latest stable ubuntu release).

There are two parts to this.  One is a Ubuntu development kernel which
we can give to large numbers of people to expand our testing pool.
But if we don't do a better job of responding to bug reports that
would be generated by expanded testing this won't necessarily help us.

The other an automated set of standard pre-built bisection points so
that testers can more easily localize a bug down to a few hundred
commits without needing to learn how to use "git bisect" (think Ubuntu
users).

So for the first, I've actually been playing with some plans to put
together an unofficial kernel that basically "what Ted is using on his
laptop".  It generally has emergency bug fixes that haven't made it
into mainline, plus some other trees where I've been more aggressive
since I want to latest in wireless and powersaving technology, etc.
It has the property that "if it breaks, you get to keep both pieces
--- and I've helpfully included the git ID in the package name so you
can do the bisection yourself".  If you want to try it, the first such
kernel is here:

       http://www.kernel.org/~tytso/tbek

I wasn't planning on talking about it until it was more fully baked,
but if people want something vaguely stable based on 2.6.24-rc2, this
might be interesting.

As for the second, I was just talking to Arjan over pizza and beer
last night, and we reached the same conclusion as Ingo, which is this
really isn't that hard.  It wouldn't be that hard to set up
infrastructure to do this, and it's just a matter of getting the disk
space and the network bandwidth togehter in the right place, plus a
relatively small amount of prgramming at least for the simplest
iteration of the idea.  (As is quite common when doing designs over
beer, we talked about some more gradious web-based schemes to do
custom built kernels that was tied to the kernel bugzilla, but first
things first. :-)

						- Ted

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:13                 ` Theodore Tso
@ 2007-11-13 17:30                   ` Alan Cox
  2007-11-13 17:33                   ` Larry Finger
                                     ` (2 subsequent siblings)
  3 siblings, 0 replies; 268+ messages in thread
From: Alan Cox @ 2007-11-13 17:30 UTC (permalink / raw)
  To: Theodore Tso
  Cc: Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

> The other an automated set of standard pre-built bisection points so
> that testers can more easily localize a bug down to a few hundred
> commits without needing to learn how to use "git bisect" (think Ubuntu
> users).

Before that you want a flowchart or instruction list of boot options to
try. A lot of errors can be localised simply by asking the reported to
boot with things like "iommu=off", "pci=routeirq", "apci=off" etc

That takes a lot less time to run through and can be very informative.

Alan

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:13                 ` Theodore Tso
  2007-11-13 17:30                   ` Alan Cox
@ 2007-11-13 17:33                   ` Larry Finger
  2007-11-13 18:55                     ` Theodore Tso
  2007-11-13 17:56                   ` Adrian Bunk
  2007-11-14 23:23                   ` Daniel Barkalow
  3 siblings, 1 reply; 268+ messages in thread
From: Larry Finger @ 2007-11-13 17:33 UTC (permalink / raw)
  To: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Theodore Tso wrote:
> On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
>> Btw, I used to test every -mm kernel. But since I've switched distros
>> (gentoo->ubuntu)
>> and I have less time, I feel it's harder to test -rc or -mm kernels (I
>> know this isn't a lkml problem
>> but more a distro problem, but I would love having an ubuntu blessed
>> repo with current dev kernel
>> for the latest stable ubuntu release).
> 
> There are two parts to this.  One is a Ubuntu development kernel which
> we can give to large numbers of people to expand our testing pool.
> But if we don't do a better job of responding to bug reports that
> would be generated by expanded testing this won't necessarily help us.

I'm very encouraged to read of your expanded testing efforts. As a bcm43xx developer, Ubuntu has
been our problem distro, mostly because your standard kernels have debugging turned off for bcm43xx.
When a Ubuntu user reports a problem and we ask for the relevant output from dmesg, they have no
information. I ask two things of all distros: (1) Turn on debugging - we don't spam the logs that
badly, and (2) forward any bugs found by your testing to the maintainer, and/or the bcm43xx mailing
list.

Thanks,

Larry



^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 15:33   ` James Bottomley
  2007-11-13 16:43     ` Randy Dunlap
@ 2007-11-13 17:46     ` Martin Bligh
  2007-11-13 18:47       ` Andrew Morton
  2007-11-14  5:07       ` David Miller
  1 sibling, 2 replies; 268+ messages in thread
From: Martin Bligh @ 2007-11-13 17:46 UTC (permalink / raw)
  To: James Bottomley
  Cc: Andrew Morton, Natalie Protasevich, davem, linux-kernel, linux-scsi

> > > http://bugzilla.kernel.org/show_bug.cgi?id=9267
> > > Kernel: 2.6.23.1
> >
> > No response from developers
>
> Urm, well, if no-one ever tells the SCSI list it's unrealistic to expect
> anyone to be working on it.  As far as I can tell, email was sent to
> Andrew Vasquez only on 31 October. However, the fault looks to be
> generic, so he probably just dropped it.

This is a technical issue with vger.kernel.org mailing lists that I've tried
addressing before - maybe davem can help fix it?

What I've tried doing is bouncing relevant postings from my procmail
filters to the list, but it seems to drop bounces (probably as spam).
Is there any way around this? (like can I get an exception to be allowed
to bounce stuff or mark it with some magic X-secret-knock: header?)

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:07     ` Thomas Gleixner
@ 2007-11-13 17:47       ` Mark Lord
  2007-11-15 16:32         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
  2007-11-13 17:54       ` [BUG] New Kernel Bugs Mark Lord
  2007-11-13 18:10       ` Russell King
  2 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 17:47 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Thomas Gleixner wrote:
> On Tue, 13 Nov 2007, Mark Lord wrote:
..
>> I *still* get very slow resume-from-RAM quite often here
>> (new in 2.6.23 kernel, wasn't there in early 2.6.23-rc*).
..
>> Something eventually times out after a minute or so
>> and it comes back.  Cannot make it happen reliably,
>> unless I'm in a hurry to get something done.  :)
>> I suspect USB here, probably the same loopy bug that
>> we added a "loop limit failsafe" for back in 2.6.21(?).
> 
> Do you have a pointer to that please ?
..

The "limit" added in the code below,
which was for messages of this form:

    hub 1-1:1.0: hub_port_status failed (err = -71)
    last message repeated 347 times

drivers/usb/hub.c:  
> static void hub_tt_kevent (struct work_struct *work)
> {
>         struct usb_hub          *hub =
>                 container_of(work, struct usb_hub, tt.kevent);
>         unsigned long           flags;
>         int                     limit = 100;
> 
>         spin_lock_irqsave (&hub->tt.lock, flags);
>         while (--limit && !list_empty (&hub->tt.clear_list)) {
>             ...

I'm not yet sure what's happening on resume now,
but there's this huge long pause with a dark screen
and then suddenly the USB subsystem comes to life
(my mouse lights up) and the system finally resumes.

More when I know more.  But it doesn't happen every time,
or even most times, so git-bisect is not possible either.

This one actually requires a developer/maintainer to put
in some effort and think about things.  Currently, that's me.

-ml

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (7 preceding siblings ...)
  2007-11-13 15:36   ` Alan Cox
@ 2007-11-13 17:49   ` Jan Kara
  2007-11-13 18:04   ` Russell King
                     ` (2 subsequent siblings)
  11 siblings, 0 replies; 268+ messages in thread
From: Jan Kara @ 2007-11-13 17:49 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

> > FILE SYSTEMS=======================================================
> > 
> > ext4: delalloc space accounting problem drops data
> > http://bugzilla.kernel.org/show_bug.cgi?id=9329
> > Kernel: 2.6.24-rc1
> No response from developers
  Actually, there has been a response (Eric asked in mailing list and
created a bug and got answer to the mailing list):
http://marc.info/?l=linux-ext4&m=119454449014728&w=2

> > POSIX Access Control Lists cause bogus file system check errors
> > http://bugzilla.kernel.org/show_bug.cgi?id=9241
> > Kernel: 2.6.23.1
> 
> Andreas did some work, seemed to lose interest.
  As I read the bug it seems that the cause was a filesystem with errors
(which were in ACL's and thus kernel didn't boot only with ACL's
enabled) and fsck fixed the problem... I would close this one as
invalid (OK, I know the filesystem had to be corrupted somehow but
unless this is at least occasionally reproducible, there's low chance of
finding the bug).

								Honza

-- 
Jan Kara <jack@suse.cz>
SuSE CR Labs

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:46               ` Ingo Molnar
@ 2007-11-13 17:50                 ` Mark Lord
  2007-11-13 18:12                   ` Adrian Bunk
                                     ` (3 more replies)
  0 siblings, 4 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 17:50 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Ingo Molnar wrote:
>
> for example git-bisect was godsent. I remember that years ago bisection 
> of a bug was a very laborous task so that it was only used as a final, 
> last-ditch approach for really nasty bugs. Today we can autonomouly 
> bisect build bugs via a simple shell command around "git-bisect run", 
> without any human interaction! This freed up testing resources 
..

It's only a godsend for the few people who happen to be kernel developers
and who happen to already use git.

It's a 540MByte download over a slow link for everyone else.

-ml

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:01                   ` Adrian Bunk
@ 2007-11-13 17:50                     ` Romano Giannetti
  2007-11-13 22:03                       ` Frans Pop
  0 siblings, 1 reply; 268+ messages in thread
From: Romano Giannetti @ 2007-11-13 17:50 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ray Lee, Giacomo A. Catenazzi, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


I jump in this discussion hoping to have some more insight on git and to
report my experience as a tester. I consider myself as half-literate in
this (I am here since 1991, more or less, and I am able to compile a
kernel and even hand-apply a patch, although I am in no way a kernel
programmer). 

On Tue, 2007-11-13 at 18:01 +0100, Adrian Bunk wrote:

> The small instruction below is enough for everyone who is able to 
> build his own kernel to do a git bisect.

> # start bisecting:
> cd linux-2.6
> git bisect start
> git bisect bad v2.6.21
> git bisect good v2.6.20
> cp /path/to/.config .
> 

This was what I did in my (in the end almost successful) bisecting when
trying to find the mmc problem (see the thread named "2.6.24-rc1 eat my
SD card"). This is true in theory, but it has some problem. The "this
commit does not compile is the easiest and in man git-bisect it's
explained how to solve it. The changes in .config options, added or
removed, are another problem when jumping back and forth from version (I
was bitten by the gadzillions new options added to hda-intel alsa
driver, but well, that is solvable with a bit of attention).

The main problem I had, and that stopped me to arrive to a definite is
this situation:

j version-bad
i
h
g unrelated (but similar) bug corrected
f
e
d unrelated (but similar) bug introduced
c
b
a version-good 

(d was the series to change drivers to use sg helpers, and g was a "fix
fallout from sg helpers" patch). Now I have a series of kernels (d, e,
f) that did not work at all and so I cannot mark them good or bad. With
the number of patches added in the free-for-all week, this is a very
probable scenario. There is a way out from this using bisect?

Romano 

PS as a suggestion, I think that added a "Reported-by", or "Tested-by",
or "Debugged-by" attribution in the repository, as happened to be in the
MMC case, is a nice an d welcomed reward for the effort.    

-- 
Sorry for the disclaimer --- ¡I cannot stop it!



--
La presente comunicación tiene carácter confidencial y es para el exclusivo uso del destinatario indicado en la misma. Si Ud. no es el destinatario indicado, le informamos que cualquier forma de distribución, reproducción o uso de esta comunicación y/o de la información contenida en la misma están estrictamente prohibidos por la ley. Si Ud. ha recibido esta comunicación por error, por favor, notifíquelo inmediatamente al remitente contestando a este mensaje y proceda a continuación a destruirlo. Gracias por su colaboración.

This communication contains confidential information. It is for the exclusive use of the intended addressee. If you are not the intended addressee, please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited by law. If you have received this communication in error, please immediately notify the sender by reply e-mail and destroy this message. Thank you for your cooperation. 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:07     ` Thomas Gleixner
  2007-11-13 17:47       ` Mark Lord
@ 2007-11-13 17:54       ` Mark Lord
  2007-11-13 22:46         ` Thomas Gleixner
  2007-11-13 18:10       ` Russell King
  2 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 17:54 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Thomas Gleixner wrote:
> On Tue, 13 Nov 2007, Mark Lord wrote:
> 
>> > Andrew Morton wrote:
>>> > > On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
>>> > > <protasnb@gmail.com> wrote:
>> > ..
>>>> > > > with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
>>>> > > > boot (ARM, Timer)
>>>> > > > http://bugzilla.kernel.org/show_bug.cgi?id=9229
>>>> > > > Kernel: 2.6.23
>>> > > 
>>> > > No response from developers
>> > ..
> 
> The bug report is bogus. ARM has no CONFIG_HPET_TIMER. 
>  
>> > Note:  that same bug exists/existed on i386 back when NO_HZ was
>> > introduced (2.6.21?).  I still see it from time to time on my Quad core
>> > system (very rare), but not any more on my Duo notebook where it used
>> > to happen about 1 in n boots (n < 10).
>> > 
>> > AFAICT no fix was ever released for it.
> 
> Hmm, at which point does the boot stop ? 
..

Just as it prints out these messages, sometimes one of them,
sometimes both (or all four on the quad core):

kernel: switched to high resolution mode on cpu 1
kernel: switched to high resolution mode on cpu 0 


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:13                 ` Theodore Tso
  2007-11-13 17:30                   ` Alan Cox
  2007-11-13 17:33                   ` Larry Finger
@ 2007-11-13 17:56                   ` Adrian Bunk
  2007-11-13 18:57                     ` Gabriel C
                                       ` (2 more replies)
  2007-11-14 23:23                   ` Daniel Barkalow
  3 siblings, 3 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 17:56 UTC (permalink / raw)
  To: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, Nov 13, 2007 at 12:13:56PM -0500, Theodore Tso wrote:
> On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
> > Btw, I used to test every -mm kernel. But since I've switched distros
> > (gentoo->ubuntu)
> > and I have less time, I feel it's harder to test -rc or -mm kernels (I
> > know this isn't a lkml problem
> > but more a distro problem, but I would love having an ubuntu blessed
> > repo with current dev kernel
> > for the latest stable ubuntu release).
> 
> There are two parts to this.  One is a Ubuntu development kernel which
> we can give to large numbers of people to expand our testing pool.
> But if we don't do a better job of responding to bug reports that
> would be generated by expanded testing this won't necessarily help us.
>...

The main problem aren't missing testers [1] - we already have relatively 
experienced people testing kernels and/or reporting bugs, and we slowly 
scare them away due to the many bug reports without any reaction.

The main problem is finding experienced developers who spend time on 
looking into bug reports.

Getting many relatively unexperienced users (who need more guidance for 
debugging issues) as additional testers is therefore IMHO not 
necessarily a good idea.

> 						- Ted

cu
Adrian

[1] and e.g. when Greg says he has a few hundred people who want to
    write drivers it would most likely be possible to find a few
    dozen additional -rc testers among them

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (8 preceding siblings ...)
  2007-11-13 17:49   ` Jan Kara
@ 2007-11-13 18:04   ` Russell King
  2007-11-14 12:46   ` Jiri Kosina
  2007-11-14 13:24   ` Pavel Machek
  11 siblings, 0 replies; 268+ messages in thread
From: Russell King @ 2007-11-13 18:04 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 03:15:53AM -0800, Andrew Morton wrote:
> On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich" <protasnb@gmail.com> wrote:
> > PLATFORM===============================================================
> > 
> > xipImage is built so that uBoot cant run it (ARM)
> > http://bugzilla.kernel.org/show_bug.cgi?id=9356
> > Kernel: 2.6.21
> 
> Zero responses from developers

For christ sake Andrew.  Some of us are not employed to do kernel work
24h x 365days a year.  You might be, I'm not.

First thing, it's not a regression.  Second thing, it's *not* a bug.

uboot requires kernel images to be specially wrapped up in their crappy
formats before uboot will recognise it.  This means that if someone wants
to boot a binary image with uboot, they need to either:

1. work out the correct 'mkimage' command and run that program after
   the kernel build has completed.

2. sort out adding a new target to the kernel makefiles to run this
   uboot specific 'mkimage' command automatically.

And Alexandre (the original feature-missing reporter) has linked to a
message where a patch was proposed to do (2).  So obviously it's no
longer a problem for the reporter.

> > with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
> > boot (ARM, Timer)
> > http://bugzilla.kernel.org/show_bug.cgi?id=9229
> > Kernel: 2.6.23
> 
> No response from developers

Bug was assigned to reporter, so I ignored it on the grounds that the
reporter was resolving it.  Plus, until recently I didn't have any
workable PXA systems to test stuff on.

In the end, a similar issue has been resolved anyway after a lot of
discussion on the ARM lists about how PXA should handle one-shot mode
with clockevents. It took absolutely ages to get agreement on what was
a simple patch.

commit 91bc51d8a10b00d8233dd5b6f07d7eb40828b87d
Author: Russell King <rmk@dyn-67.arm.linux.org.uk>
Date:   Thu Nov 8 23:35:46 2007 +0000

    [ARM] pxa: fix one-shot timer mode

    One-shot timer mode on PXA has various bugs which prevent kernels
    build with NO_HZ enabled booting.  They end up spinning on a
    permanently asserted timer interrupt because we don't properly
    clear it down - clearing the OIER bit does not stop the pending
    interrupt status.  Fix this in the set_mode handler as well.

    Moreover, the code which sets the next expiry point may race with
    the hardware, and we might not set the match register sufficiently
    in the future.  If we encounter that situation, return -ETIME so
    the generic time code retries.

    Acked-by: Thomas Gleixner <tglx@linutronix.de>
    Acked-by: Nicolas Pitre <nico@cam.org>
    Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Ergo, the bug can be closed provided the reporter re-tests a recent git
snapshot.  Sorry, no idea how the above commit relates to Linus' releases
and/or git snapshots.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:07     ` Thomas Gleixner
  2007-11-13 17:47       ` Mark Lord
  2007-11-13 17:54       ` [BUG] New Kernel Bugs Mark Lord
@ 2007-11-13 18:10       ` Russell King
  2007-11-13 18:25         ` Alan Cox
  2 siblings, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 18:10 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Mark Lord, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	Natalie Protasevich, linux-ide, bugme-daemon, linux-input,
	Andrew Morton

On Tue, Nov 13, 2007 at 05:07:21PM +0100, Thomas Gleixner wrote:
> On Tue, 13 Nov 2007, Mark Lord wrote:
> 
> > Andrew Morton wrote:
> > > On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
> > > <protasnb@gmail.com> wrote:
> > ..
> > > > with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23 doesn't
> > > > boot (ARM, Timer)
> > > > http://bugzilla.kernel.org/show_bug.cgi?id=9229
> > > > Kernel: 2.6.23
> > > 
> > > No response from developers
> > ..
> 
> The bug report is bogus. ARM has no CONFIG_HPET_TIMER. 

Plus we've just merged a fix for NO_HZ on PXA platforms due to an utterly
broken one-shot implementation.  So chances are this problem is now fixed.

However, I object strongly to Andrew's responses to these bugs.  He's
completely out of line.

Given the wide range of ARM platforms today, it is utterly idiotic to
expect a single person to be able to provide responses for all ARM bugs.
I for one wish I'd never *VOLUNTEERED* to be a part of the kernel
bugzilla, and really *WISH* I could pull out of that function.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:50                 ` Mark Lord
@ 2007-11-13 18:12                   ` Adrian Bunk
  2007-11-13 18:18                     ` Mark Lord
  2007-11-13 18:17                   ` Peter Zijlstra
                                     ` (2 subsequent siblings)
  3 siblings, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 18:12 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 12:50:08PM -0500, Mark Lord wrote:
> Ingo Molnar wrote:
>>
>> for example git-bisect was godsent. I remember that years ago bisection of 
>> a bug was a very laborous task so that it was only used as a final, 
>> last-ditch approach for really nasty bugs. Today we can autonomouly bisect 
>> build bugs via a simple shell command around "git-bisect run", without any 
>> human interaction! This freed up testing resources 
> ..
>
> It's only a godsend for the few people who happen to be kernel developers

It's also godsend for users who want a regression they observe fixed.

If you can tell which patch broke it you often turned a very hard to 
debug problem into a relatively easy fixable problem.

As an example, [1] was an issue a normal user could discover, and 
bisecting made the difference between "nearly undebuggable" and
"easily fixable by revertng a commit".

> and who happen to already use git.

As already said in thread, the required instructions for bisecting are 
relatively short and simple (assuming the user can build his own 
kernels).

> It's a 540MByte download over a slow link for everyone else.

Not everyone has a slow connection.

For me, the speed of cloning a tree from git.kernel.org is completely 
cpu bound and limited by the speed of the 1.8 Ghz Athlon in my 
computer...

But if there is a real life problem like people with extremely slow and 
expensive internet connections not being able to bisect bugs these 
problems should be named and fixed (e.g. by sending CDs).

> -ml

cu
Adrian

[1] http://lkml.org/lkml/2007/11/12/154

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:50                 ` Mark Lord
  2007-11-13 18:12                   ` Adrian Bunk
@ 2007-11-13 18:17                   ` Peter Zijlstra
  2007-11-13 18:39                   ` Matthew Wilcox
  2007-11-18 12:44                   ` size of git repository (was Re: [BUG] New Kernel Bugs) Pavel Machek
  3 siblings, 0 replies; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-13 18:17 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon


On Tue, 2007-11-13 at 12:50 -0500, Mark Lord wrote:
> Ingo Molnar wrote:
> >
> > for example git-bisect was godsent. I remember that years ago bisection 
> > of a bug was a very laborous task so that it was only used as a final, 
> > last-ditch approach for really nasty bugs. Today we can autonomouly 
> > bisect build bugs via a simple shell command around "git-bisect run", 
> > without any human interaction! This freed up testing resources 
> ...
> 
> It's only a godsend for the few people who happen to be kernel developers
> and who happen to already use git.
> 
> It's a 540MByte download over a slow link for everyone else.

Oh, common. Leeching CDs is so yesterday. These days some distributions
don't even offer CDs anymore in favour of DVDs.

I'd be amazed if a lot of the testers would still be on slownet, its
impossible to keep up with the latest distros without broadband.



^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:12                   ` Adrian Bunk
@ 2007-11-13 18:18                     ` Mark Lord
  2007-11-13 18:36                       ` Adrian Bunk
  2007-11-14  1:10                       ` David Miller
  0 siblings, 2 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 18:18 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 12:50:08PM -0500, Mark Lord wrote:
>> Ingo Molnar wrote:
>>> for example git-bisect was godsent. I remember that years ago bisection of 
>>> a bug was a very laborous task so that it was only used as a final, 
>>> last-ditch approach for really nasty bugs. Today we can autonomouly bisect 
>>> build bugs via a simple shell command around "git-bisect run", without any 
>>> human interaction! This freed up testing resources 
>> ..
>>
>> It's only a godsend for the few people who happen to be kernel developers
> 
> It's also godsend for users who want a regression they observe fixed.
> 
> If you can tell which patch broke it you often turned a very hard to 
> debug problem into a relatively easy fixable problem.
..

Oh yes, definitely.  When that use happens to be a kernel dev + git user,
it saves the *fool who broke it* a hell of a lot of time, because they can
slough it off onto the poor bloke who notices it.

Mind you, no arguing that this is effective when that poor bloke
has a day free to download the git-tree and build/reboot a dozen times.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:10       ` Russell King
@ 2007-11-13 18:25         ` Alan Cox
  2007-11-13 22:34           ` Russell King
  0 siblings, 1 reply; 268+ messages in thread
From: Alan Cox @ 2007-11-13 18:25 UTC (permalink / raw)
  To: Russell King
  Cc: Thomas Gleixner, Mark Lord, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, Natalie Protasevich, linux-ide, bugme-daemon,
	linux-input, Andrew Morton

> Given the wide range of ARM platforms today, it is utterly idiotic to
> expect a single person to be able to provide responses for all ARM bugs.
> I for one wish I'd never *VOLUNTEERED* to be a part of the kernel
> bugzilla, and really *WISH* I could pull out of that function.

You can. Perhaps that bugzilla needs to point to some kind of
arm-maintainers@vger.kernel.org list for the various ARM platform
maintainers ?

Alan

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:18                     ` Mark Lord
@ 2007-11-13 18:36                       ` Adrian Bunk
  2007-11-13 18:47                         ` Mark Lord
  2007-11-14  1:10                       ` David Miller
  1 sibling, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 18:36 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 01:18:43PM -0500, Mark Lord wrote:
> Adrian Bunk wrote:
>> On Tue, Nov 13, 2007 at 12:50:08PM -0500, Mark Lord wrote:
>>> Ingo Molnar wrote:
>>>> for example git-bisect was godsent. I remember that years ago bisection 
>>>> of a bug was a very laborous task so that it was only used as a final, 
>>>> last-ditch approach for really nasty bugs. Today we can autonomouly 
>>>> bisect build bugs via a simple shell command around "git-bisect run", 
>>>> without any human interaction! This freed up testing resources 
>>> ..
>>>
>>> It's only a godsend for the few people who happen to be kernel developers
>>
>> It's also godsend for users who want a regression they observe fixed.
>>
>> If you can tell which patch broke it you often turned a very hard to debug 
>> problem into a relatively easy fixable problem.
> ..
>
> Oh yes, definitely.  When that use happens to be a kernel dev + git user,
> it saves the *fool who broke it* a hell of a lot of time, because they can
> slough it off onto the poor bloke who notices it.

"fool who broke it" are hard works. Bugs are part of software 
development, so you'd have to name everyone who develops software
a fool.

But the main point is that often you don't know who broke it until you 
know which commit broke it.

> Mind you, no arguing that this is effective when that poor bloke
> has a day free to download the git-tree and build/reboot a dozen times.

I did bisecting myself, and I know that it costs time and work.

But the first point is the above one that it makes otherwise nearly 
undebuggable problems debuggable and fixable.

Another point is that it shifts the work from the few experienced 
developers to the many users. Users (and voluntary testers) we have
many, but developer time for debugging bug reports is a quite scarce 
resource.

And why "poor bloke"? Bisecting takes time, but that's not different 
from e.g. writing code or cleaning up code or going through bug reports.

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:50                 ` Mark Lord
  2007-11-13 18:12                   ` Adrian Bunk
  2007-11-13 18:17                   ` Peter Zijlstra
@ 2007-11-13 18:39                   ` Matthew Wilcox
  2007-11-13 18:43                     ` Mark Lord
  2007-11-18 12:44                   ` size of git repository (was Re: [BUG] New Kernel Bugs) Pavel Machek
  3 siblings, 1 reply; 268+ messages in thread
From: Matthew Wilcox @ 2007-11-13 18:39 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

On Tue, Nov 13, 2007 at 12:50:08PM -0500, Mark Lord wrote:
> It's a 540MByte download over a slow link for everyone else.

Where do you get this number from?
$ du -sh .git/objects/pack/
249M    .git/objects/pack/
$ du -sh .git/objects/
253M    .git/objects/

ie about half what you claim.

-- 
Intel are signing my paycheques ... these opinions are still mine
"Bill, look, we understand that you're interested in selling us this
operating system, but compare it to ours.  We can't possibly take such
a retrograde step."

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:39                   ` Matthew Wilcox
@ 2007-11-13 18:43                     ` Mark Lord
  2007-11-13 18:49                       ` Matthew Wilcox
  0 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 18:43 UTC (permalink / raw)
  To: Matthew Wilcox
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

Matthew Wilcox wrote:
> On Tue, Nov 13, 2007 at 12:50:08PM -0500, Mark Lord wrote:
>> It's a 540MByte download over a slow link for everyone else.
> 
> Where do you get this number from?
> $ du -sh .git/objects/pack/
> 249M    .git/objects/pack/
> $ du -sh .git/objects/
> 253M    .git/objects/
> 
> ie about half what you claim.
..

No, it's from earlier in this very thread:

Adrian Bunk wrote:
> The small instruction below is enough for everyone who is able to 
> build his own kernel to do a git bisect.
..
> <--  snip  -->
> 
> 
> # install git
> 
> # clone Linus' tree:
> git clone \ 
> git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
..

mkdir t
cd t
git clone git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
(wait half an hour)
/usr/bin/du -s linux-2.6
522732  linux-2.6




^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:36                       ` Adrian Bunk
@ 2007-11-13 18:47                         ` Mark Lord
  2007-11-13 19:04                           ` Adrian Bunk
  0 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 18:47 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Adrian Bunk wrote:
...
> I did bisecting myself, and I know that it costs time and work.
> 
> But the first point is the above one that it makes otherwise nearly 
> undebuggable problems debuggable and fixable.
..

Definitely useful, no question.

But the problem is now that kernel devs are addicted to it,
many won't even consider resolving a problem any other way.

That's not "maintaining" (or supporting) one's code.

And when a "maintainer" is too busy to find/fix their own bugs,
that could be a sign that they've bitten off too big of a chunk
of the kernel, and it's time for them to distribute code maintainership.

Cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:46     ` Martin Bligh
@ 2007-11-13 18:47       ` Andrew Morton
  2007-11-14  5:07       ` David Miller
  1 sibling, 0 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 18:47 UTC (permalink / raw)
  To: Martin Bligh
  Cc: James Bottomley, Natalie Protasevich, davem, linux-kernel, linux-scsi

On Tue, 13 Nov 2007 09:46:08 -0800 "Martin Bligh" <mbligh@google.com> wrote:

> > > > http://bugzilla.kernel.org/show_bug.cgi?id=9267
> > > > Kernel: 2.6.23.1
> > >
> > > No response from developers
> >
> > Urm, well, if no-one ever tells the SCSI list it's unrealistic to expect
> > anyone to be working on it.  As far as I can tell, email was sent to
> > Andrew Vasquez only on 31 October. However, the fault looks to be
> > generic, so he probably just dropped it.

I looked at that one and decided not to forward it to anyone because it was
already sent to Andrew.  Oh well, sorry.

> This is a technical issue with vger.kernel.org mailing lists that I've tried
> addressing before - maybe davem can help fix it?
> 
> What I've tried doing is bouncing relevant postings from my procmail
> filters to the list, but it seems to drop bounces (probably as spam).
> Is there any way around this? (like can I get an exception to be allowed
> to bounce stuff or mark it with some magic X-secret-knock: header?)

Please let me know asap if/when this starts working so I don't start
forwarding duplicates everywhere.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:43                     ` Mark Lord
@ 2007-11-13 18:49                       ` Matthew Wilcox
  2007-11-13 18:54                         ` Mark Lord
  0 siblings, 1 reply; 268+ messages in thread
From: Matthew Wilcox @ 2007-11-13 18:49 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

On Tue, Nov 13, 2007 at 01:43:53PM -0500, Mark Lord wrote:
> Matthew Wilcox wrote:
> >ie about half what you claim.
> ..
> 
> No, it's from earlier in this very thread:
> 
> Adrian Bunk wrote:
> >git clone \ 
> >git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
> ..
> 
> mkdir t
> cd t
> git clone 
> git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
> (wait half an hour)
> /usr/bin/du -s linux-2.6
> 522732  linux-2.6

You're assuming that everything in linux-2.6 was downloaded; that's
not true.  Everything in linux-2.6/.git was downloaded; but then you do a
checkout which happens to approximately double the size of the linux-2.6
directory.  If you do git-clone -n, you'll get a closer estimate to the
size of the download.

I suppose git-clone should grow a -v option that it could pass to rsync
to let us find out how many bytes are actually transferred, but i'm
happy to go with 250MB as a close estimate to the amount of data to xfer.

When you compare it to the 60MB tarballs that are published, it's really
not that bad.

-- 
Intel are signing my paycheques ... these opinions are still mine
"Bill, look, we understand that you're interested in selling us this
operating system, but compare it to ours.  We can't possibly take such
a retrograde step."

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:49                       ` Matthew Wilcox
@ 2007-11-13 18:54                         ` Mark Lord
  2007-11-13 22:09                           ` Rafael J. Wysocki
  2007-11-14 14:30                           ` Ingo Molnar
  0 siblings, 2 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 18:54 UTC (permalink / raw)
  To: Matthew Wilcox
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

Matthew Wilcox wrote:
> On Tue, Nov 13, 2007 at 01:43:53PM -0500, Mark Lord wrote:
>
>> mkdir t
>> cd t
>> git clone 
>> git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
>> (wait half an hour)
>> /usr/bin/du -s linux-2.6
>> 522732  linux-2.6
> 
> You're assuming that everything in linux-2.6 was downloaded; that's
> not true.  Everything in linux-2.6/.git was downloaded; but then you do a
> checkout which happens to approximately double the size of the linux-2.6
> directory. 
..

Ah, I wondered why it took only half an hour to download.

..
> When you compare it to the 60MB tarballs that are published, it's really
> not that bad.
..

The tarballs I download are only 45MB.

Cheers


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:33                   ` Larry Finger
@ 2007-11-13 18:55                     ` Theodore Tso
  2007-11-13 20:07                       ` Larry Finger
  0 siblings, 1 reply; 268+ messages in thread
From: Theodore Tso @ 2007-11-13 18:55 UTC (permalink / raw)
  To: Larry Finger
  Cc: Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, Nov 13, 2007 at 11:33:44AM -0600, Larry Finger wrote:
> I'm very encouraged to read of your expanded testing efforts. As a
> bcm43xx developer, Ubuntu has been our problem distro, mostly
> because your standard kernels have debugging turned off for bcm43xx.
> When a Ubuntu user reports a problem and we ask for the relevant
> output from dmesg, they have no information. I ask two things of all
> distros: (1) Turn on debugging - we don't spam the logs that badly,
> and (2) forward any bugs found by your testing to the maintainer,
> and/or the bcm43xx mailing list.

Heh. I hadn't enabled CONFIG_BCM43XX_DEBUG myself, but I just changed
it for my next kernel build.  This is a slightly different issue,
which is that sometimes _DEBUG options shouldn't be turned on by
default (because they really trash performance and bloat log size),
and sometimes they are painless to turn on and don't cost much.

If that is the case, I'd suggest removing the option and just making
it compiled in by default with a run-time option to enable it.

   	       	  	       	 	  - Ted


   	      


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:56                   ` Adrian Bunk
@ 2007-11-13 18:57                     ` Gabriel C
  2007-11-14  0:41                       ` Denys Vlasenko
  2007-11-14  0:39                     ` Denys Vlasenko
  2007-11-14 16:55                     ` Jan Evert van Grootheest
  2 siblings, 1 reply; 268+ messages in thread
From: Gabriel C @ 2007-11-13 18:57 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 12:13:56PM -0500, Theodore Tso wrote:
>> On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
>>> Btw, I used to test every -mm kernel. But since I've switched distros
>>> (gentoo->ubuntu)
>>> and I have less time, I feel it's harder to test -rc or -mm kernels (I
>>> know this isn't a lkml problem
>>> but more a distro problem, but I would love having an ubuntu blessed
>>> repo with current dev kernel
>>> for the latest stable ubuntu release).
>> There are two parts to this.  One is a Ubuntu development kernel which
>> we can give to large numbers of people to expand our testing pool.
>> But if we don't do a better job of responding to bug reports that
>> would be generated by expanded testing this won't necessarily help us.
>> ...
> 
> The main problem is finding experienced developers who spend time on 
> looking into bug reports.

There are already. IMO the problem is the development model.

There are tons new features in each new kernel release and 'tons new bugs'
which are not fixed during the release cycle nor in the .XX stable kernels.

Maybe after XX kernel releases there should be one just with bug-fixes _without_ any
new features , eg: cleaning bugs from bugzilla , know regressions , cleaning up code , 
removing broken drivers and the like.


> cu
> Adrian

Gabriel 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 12:32           ` David Miller
@ 2007-11-13 19:02             ` Andrew Morton
  2007-11-13 20:00               ` Christian Kujau
  2007-11-13 19:32             ` [BUG] New Kernel Bugs Russell King
  1 sibling, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 19:02 UTC (permalink / raw)
  To: David Miller
  Cc: protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 04:32:07 -0800 (PST) David Miller <davem@davemloft.net> wrote:

> From: Andrew Morton <akpm@linux-foundation.org>
> Date: Tue, 13 Nov 2007 04:12:59 -0800
> 
> > On Tue, 13 Nov 2007 03:58:24 -0800 (PST) David Miller <davem@davemloft.net> wrote:
> > 
> > > From: Andrew Morton <akpm@linux-foundation.org>
> > > Date: Tue, 13 Nov 2007 03:49:16 -0800
> > > 
> > > > Do you believe that our response to bug reports is adequate?
> > > 
> > > Do you feel that making us feel and look like shit helps?
> > 
> > That doesn't answer my question.
> > 
> > See, first we need to work out whether we have a problem.  If we do this,
> > then we can then have a think about what to do about it.
> > 
> > I tried to convince the 2006 KS attendees that we have a problem and I
> > resoundingly failed.  People seemed to think that we're doing OK.
> > 
> > But it appears that data such as this contradicts that belief.
> > 
> > This is not a minor matter.  If the kernel _is_ slowly deteriorating then
> > this won't become readily apparent until it has been happening for a number
> > of years.  By that stage there will be so much work to do to get us back to
> > an acceptable level that it will take a huge effort.  And it will take a
> > long time after that for the kerel to get its reputation back.
> > 
> > So it is important that we catch deterioration *early* if it is happening.
> 
> You tell me what I should spend my time working on, and I promise to
> do it OK? :-)

My suggestion: regressions.

If we're really active in chasing down the regressions then I think we can
be confident that the kernel isn't deteriorating.  Probably it will be
improving as we also fix some always-been-there bugs.

I think that we're fairly good about working the regressions in
Adrian/Michal/Rafael's lists but once Linus releases 2.6.x we tend to let
the unsolved ones slide, and we don't pay as much attention to the
regressions which 2.6.x testers report.

> For example, if I have a choice between a TCP crash just about anyone
> can hit and some obscure issue only reported with some device nearly
> nobody has, which one should I analyze and work on?
> 
> That's the problem.  All of us prioritize and it means the chaff
> collects at the bottom.  You cannot fix that except by getting more
> bug fixers so that the chaff pile has a chance to get smaller.
> 
> Luckily if the report being ignored isn't chaff, it will show up again
> (and again and again) and this triggers a reprioritization because not
> only is the bug no longer chaff, it also now got a lot of information
> tagged to it so it's a double worthwhile investment to work on the
> problem.
> 
> I think a lot of bugs that "aren't getting looked at" are simply
> sitting in some early stage of this process.

Yes, that's a useful technique.  If multiple people are being hurt a lot by
a bug then that's a more important one to fix than the single-person
minor-irritant bug.

otoh that doesn't work very well with driver/platform bugs.  Often these
are regressions which only a single person can reproduce within the time
window which we have in which we can fix it.  If we don't fix it in that
window it'll go out to distros and presumably some more people will hit it.

So I don't see much alternative here to the traditional
work-with-the-originator way of resolving it.

git bisection should really help us with these regressions but it doesn't
appear that people are using as much as one would like.  I'm hoping that
the very good http://www.kernel.org/doc/local/git-quick.html will help us
out here.  Thanks to the mystery person who prepared that.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:47                         ` Mark Lord
@ 2007-11-13 19:04                           ` Adrian Bunk
  2007-11-13 19:12                             ` Mark Lord
  2007-11-13 19:26                             ` Mark Lord
  0 siblings, 2 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 19:04 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 01:47:10PM -0500, Mark Lord wrote:
> Adrian Bunk wrote:
> ...
>> I did bisecting myself, and I know that it costs time and work.
>>
>> But the first point is the above one that it makes otherwise nearly 
>> undebuggable problems debuggable and fixable.
> ..
>
> Definitely useful, no question.
>
> But the problem is now that kernel devs are addicted to it,
> many won't even consider resolving a problem any other way.
>
> That's not "maintaining" (or supporting) one's code.

What you replaced with two dots contained the answer to this:

Another point is that it shifts the work from the few experienced 
developers to the many users. Users (and voluntary testers) we have
many, but developer time for debugging bug reports is a quite scarce 
resource.

> And when a "maintainer" is too busy to find/fix their own bugs,
> that could be a sign that they've bitten off too big of a chunk
> of the kernel, and it's time for them to distribute code maintainership.

The problem is: Maintainers don't grow on trees.

You need people who are both technically capable and willing to spend 
time on the non-sexy task of debugging problems.

Where do you plan to find them?

If you don't believe me, please find a maintainer for the currently 
unmaintained parallel port support.

Or if you want a harder task, find a maintainer for the floppy driver...

> Cheers

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:04                           ` Adrian Bunk
@ 2007-11-13 19:12                             ` Mark Lord
  2007-11-13 19:30                               ` Adrian Bunk
  2007-11-13 19:26                             ` Mark Lord
  1 sibling, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 19:12 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 01:47:10PM -0500, Mark Lord wrote:
>> Adrian Bunk wrote:
>> ...
>>> I did bisecting myself, and I know that it costs time and work.
>>>
>>> But the first point is the above one that it makes otherwise nearly 
>>> undebuggable problems debuggable and fixable.
>> ..
>>
>> Definitely useful, no question.
>>
>> But the problem is now that kernel devs are addicted to it,
>> many won't even consider resolving a problem any other way.
>>
>> That's not "maintaining" (or supporting) one's code.
> 
> What you replaced with two dots contained the answer to this:
> 
> Another point is that it shifts the work from the few experienced 
> developers to the many users. Users (and voluntary testers) we have
> many, but developer time for debugging bug reports is a quite scarce 
> resource.
> 
>> And when a "maintainer" is too busy to find/fix their own bugs,
>> that could be a sign that they've bitten off too big of a chunk
>> of the kernel, and it's time for them to distribute code maintainership.
> 
> The problem is: Maintainers don't grow on trees.
> 
> You need people who are both technically capable and willing to spend 
> time on the non-sexy task of debugging problems.
> 
> Where do you plan to find them?
> 
> If you don't believe me, please find a maintainer for the currently 
> unmaintained parallel port support.
> 
> Or if you want a harder task, find a maintainer for the floppy driver...
..

Again, the problem is:

> But the problem is now that kernel devs are addicted to it,
> many won't even consider resolving a problem any other way.

And that's simply not good enough.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:04                           ` Adrian Bunk
  2007-11-13 19:12                             ` Mark Lord
@ 2007-11-13 19:26                             ` Mark Lord
  2007-11-13 20:00                               ` Adrian Bunk
  1 sibling, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 19:26 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 01:47:10PM -0500, Mark Lord wrote:
>> Adrian Bunk wrote:
..
> Another point is that it shifts the work from the few experienced 
> developers to the many users. Users (and voluntary testers) we have
> many, but developer time for debugging bug reports is a quite scarce 
> resource.
> 
>> And when a "maintainer" is too busy to find/fix their own bugs,
>> that could be a sign that they've bitten off too big of a chunk
>> of the kernel, and it's time for them to distribute code maintainership.
> 
> The problem is: Maintainers don't grow on trees.
..

Hey, if somebody has time to break things, then they damn well ought
to be able to make time to fix them again.  And the best developers
here on LKML do just that (fix what they break).

You broke it, you fix it.  A simple rule.

Translation for the particularly daft:

If you've been making significant updates to a driver/subsystem,
and people are reporting that it is now broken for them,
then it's your job to make it right.  The reporters can help,
and many may even git-bisect or send patches.  

But you cannot *expect* or *insist* upon them doing your job.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:12                             ` Mark Lord
@ 2007-11-13 19:30                               ` Adrian Bunk
  2007-11-13 19:46                                 ` Russell King
  0 siblings, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 19:30 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 02:12:57PM -0500, Mark Lord wrote:
> Adrian Bunk wrote:
>> On Tue, Nov 13, 2007 at 01:47:10PM -0500, Mark Lord wrote:
>>> Adrian Bunk wrote:
>>> ...
>>>> I did bisecting myself, and I know that it costs time and work.
>>>>
>>>> But the first point is the above one that it makes otherwise nearly 
>>>> undebuggable problems debuggable and fixable.
>>> ..
>>>
>>> Definitely useful, no question.
>>>
>>> But the problem is now that kernel devs are addicted to it,
>>> many won't even consider resolving a problem any other way.
>>>
>>> That's not "maintaining" (or supporting) one's code.
>>
>> What you replaced with two dots contained the answer to this:
>>
>> Another point is that it shifts the work from the few experienced 
>> developers to the many users. Users (and voluntary testers) we have
>> many, but developer time for debugging bug reports is a quite scarce 
>> resource.
>>
>>> And when a "maintainer" is too busy to find/fix their own bugs,
>>> that could be a sign that they've bitten off too big of a chunk
>>> of the kernel, and it's time for them to distribute code maintainership.
>>
>> The problem is: Maintainers don't grow on trees.
>>
>> You need people who are both technically capable and willing to spend time 
>> on the non-sexy task of debugging problems.
>>
>> Where do you plan to find them?
>>
>> If you don't believe me, please find a maintainer for the currently 
>> unmaintained parallel port support.
>>
>> Or if you want a harder task, find a maintainer for the floppy driver...
> ..
>
> Again, the problem is:
>
>> But the problem is now that kernel devs are addicted to it,
>> many won't even consider resolving a problem any other way.
>
> And that's simply not good enough.

There is this silly limit that noone can work more than 168 hours per 
week on the Linux kernel, and some kernel developers seem to take the 
liberty of spending even less time on kernel development...

Considering our problems to cope with the amount of incoming bug 
reports, everything that would require a kernel developer to spend more 
time for getting a bug fixed would be a horrible mistake.

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 12:32           ` David Miller
  2007-11-13 19:02             ` Andrew Morton
@ 2007-11-13 19:32             ` Russell King
  2007-11-13 20:13               ` Adrian Bunk
  2007-11-13 20:52               ` Andrew Morton
  1 sibling, 2 replies; 268+ messages in thread
From: Russell King @ 2007-11-13 19:32 UTC (permalink / raw)
  To: David Miller
  Cc: akpm, alsa-devel, netdev, linux-pcmcia, linux-kernel, protasnb,
	linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 04:32:07AM -0800, David Miller wrote:
> Luckily if the report being ignored isn't chaff, it will show up again
> (and again and again) and this triggers a reprioritization because not
> only is the bug no longer chaff, it also now got a lot of information
> tagged to it so it's a double worthwhile investment to work on the
> problem.

Strongly agree.

This is exactly what happened to that ARM NO_HZ bug report.  The report
in bugzilla was rather lacking (and wrong) in ways that have already
been described.  HPET on ARM? 8)

Then on the morning of 6th November, someone reported on the mailing list
that "pxa270 doesn't work with oneshot timer" and that was the trigger to
getting the bug resolved - because it was a narrowly defined bug report.

Since it was a narrowly defined bug report, it became very easy to
investigate and resolve.  About half an hour of time for an initial
patch.


There's another issue I want to raise concerning bugzilla.  We have the
classic case of "not enough people reading bugzilla bugs" - which is one
of the biggest problems with bugzilla.  Virtually no one in the ARM
community looks for ARM bugs in bugzilla.

Let's not forget that it would be a waste of time for people to manually
check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
into bugzilla that a weekly manual check by every maintainer would just
return the same old boring results for months and months at a time.

It would be far more productive if the ARM category was deleted from
bugzilla and the few people who use bugzilla reported their bugs on the
mailing list.  We've a couple of thousand people on the ARM kernel
mailing list at the moment - that's 3 orders of magnitude more of eyes
than look at bugzilla.

(I'm not saying that if the ARM NO_HZ bug as reported in bugzilla had
been reported on the correct mailing list would've been solved earlier;
I doubt there'd be much difference.  However, the probability of a
question being asked of the reporter would've been much higher, and
_that_ might have led to an earlier resolution.)

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:08             ` Mark Lord
                                 ` (2 preceding siblings ...)
  2007-11-13 16:46               ` Ingo Molnar
@ 2007-11-13 19:37               ` Russell King
  2007-11-13 20:18                 ` Mark Lord
  2007-11-14  0:34               ` Denys Vlasenko
  4 siblings, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 19:37 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

On Tue, Nov 13, 2007 at 09:08:32AM -0500, Mark Lord wrote:
> Ingo Molnar wrote:
> ..
> > This is all QA-101 that _cannot be argued against on a rational basis_, 
> > it's just that these sorts of things have been largely ignored for 
> > years, in favor of the all-too-easy "open source means many eyeballs and 
> > that is our QA" answer, which is a _good_ answer but by far not the most 
> > intelligent answer! Today "many eyeballs" is simply not good enough and 
> > nature (and other OS projects) will route us around if we dont change.
> ..
> 
> QA-101 and "many eyeballs" are not at all in opposition.
> The latter is how we find out about bugs on uncommon hardware,
> and the former is what we need to track them and overall quality.
> 
> A HUGE problem I have with current "efforts", is that once someone
> reports a bug, the onus seems to be 99% on the *reporter* to find
> the exact line of code or commit.  Ghad what a repressive method.

99% on the reporter?  Is that why I always try to understand the
reporters problem (*provided* it's in an area I know about) and come
up with a patch to test a theory or fix the issue?

I'm _less_ inclined to provide such a "service" for lazy maintainers
who've moved off into new and wonderfully exciting technologies, to
churn out more patches for me to merge (and eventually provide a free
to them bug fixing service for.)

That's "less" inclined, not "won't".

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:30                               ` Adrian Bunk
@ 2007-11-13 19:46                                 ` Russell King
  2007-11-13 20:04                                   ` Adrian Bunk
  0 siblings, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 19:46 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Mark Lord, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, David Miller, linux-ide, bugme-daemon, linux-input,
	Ingo Molnar, Andrew Morton

On Tue, Nov 13, 2007 at 08:30:35PM +0100, Adrian Bunk wrote:
> There is this silly limit that noone can work more than 168 hours per 
> week on the Linux kernel, and some kernel developers seem to take the 
> liberty of spending even less time on kernel development...

That limit of 168 hours applies all around the world to everyone.
Moreover, not all kernel developers are employed to hack on the
kernel for 168 hours a week.

For me, personally, that figure is in reality about 24 hours a
week.  Yes, just 24.  The rest of the time (like *now*) is time I'm
volunteering because I happen to be reading my email...

... and happen to be wasting replying to discussions like this rather
than reading that message which has just arrived on the ARM kernel
mailing list from someone having problems using copy_from_user()
with a kernel pointer.

So, please, stop this idea that somehow kernel developers can
somehow spend infinite amounts of time solving lots and lots of
bugs.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:26                             ` Mark Lord
@ 2007-11-13 20:00                               ` Adrian Bunk
  2007-11-13 20:13                                 ` Mark Lord
  2007-11-13 21:12                                 ` Alan Cox
  0 siblings, 2 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 20:00 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 02:26:05PM -0500, Mark Lord wrote:
> Adrian Bunk wrote:
>> On Tue, Nov 13, 2007 at 01:47:10PM -0500, Mark Lord wrote:
>>> Adrian Bunk wrote:
> ..
>> Another point is that it shifts the work from the few experienced 
>> developers to the many users. Users (and voluntary testers) we have
>> many, but developer time for debugging bug reports is a quite scarce 
>> resource.
>>
>>> And when a "maintainer" is too busy to find/fix their own bugs,
>>> that could be a sign that they've bitten off too big of a chunk
>>> of the kernel, and it's time for them to distribute code maintainership.
>>
>> The problem is: Maintainers don't grow on trees.
> ..
>
> Hey, if somebody has time to break things, then they damn well ought
> to be able to make time to fix them again.  And the best developers
> here on LKML do just that (fix what they break).
>
> You broke it, you fix it.  A simple rule.
>
> Translation for the particularly daft:
>
> If you've been making significant updates to a driver/subsystem,
> and people are reporting that it is now broken for them,

What are "significant updates"?

Sometimes one person makes one small patch and this patch contains
a typo.

> then it's your job to make it right.

We have some open drivers/ata/ regressions.

I see some person named "Mark Lord" being responsible for 4 commits.

What pubishment do you plan for him if 2.6.24 ships with any libata 
regressions?

Let George W. Bush wrongly accuse him of possessing weapons of 
mass destructions and invade Canada?

> The reporters can help,
> and many may even git-bisect or send patches.  
> But you cannot *expect* or *insist* upon them doing your job.

Bullshit.

Bug fixing is not about finding someone to blame, it's about getting the 
bug fixed.

The bug reporter is the person who can reproduce the problem, and if 
it's a regression then bisecting is the natural way of getting nearer 
at getting it fixed.

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:02             ` Andrew Morton
@ 2007-11-13 20:00               ` Christian Kujau
  2007-11-13 21:04                 ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Christian Kujau @ 2007-11-13 20:00 UTC (permalink / raw)
  To: Andrew Morton; +Cc: linux-kernel, torvalds

On Tue, 13 Nov 2007, Andrew Morton wrote:
> I think that we're fairly good about working the regressions in
> Adrian/Michal/Rafael's lists but once Linus releases 2.6.x we tend to let
> the unsolved ones slide, and we don't pay as much attention to the
> regressions which 2.6.x testers report.

Can't we wait until all regressions[0] are fixed before releasing a new 
2.6.x? I'd consider regressions a *literal* show stopper, and with this 
policy they just have be fixed, nothing would "slide"...

my 2 cents,
Christian.

[0] preferably only reproducible regressions, with responsive reporters.
-- 
BOFH excuse #380:

Operators killed when huge stack of backup tapes fell over.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:46                                 ` Russell King
@ 2007-11-13 20:04                                   ` Adrian Bunk
  0 siblings, 0 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 20:04 UTC (permalink / raw)
  To: Mark Lord, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, David Miller, linux-ide, bugme-daemon, linux-input,
	Ingo Molnar, Andrew Morton

On Tue, Nov 13, 2007 at 07:46:49PM +0000, Russell King wrote:
> On Tue, Nov 13, 2007 at 08:30:35PM +0100, Adrian Bunk wrote:
> > There is this silly limit that noone can work more than 168 hours per 
> > week on the Linux kernel, and some kernel developers seem to take the 
> > liberty of spending even less time on kernel development...
> 
> That limit of 168 hours applies all around the world to everyone.
> Moreover, not all kernel developers are employed to hack on the
> kernel for 168 hours a week.
> 
> For me, personally, that figure is in reality about 24 hours a
> week.  Yes, just 24.  The rest of the time (like *now*) is time I'm
> volunteering because I happen to be reading my email...
> 
> ... and happen to be wasting replying to discussions like this rather
> than reading that message which has just arrived on the ARM kernel
> mailing list from someone having problems using copy_from_user()
> with a kernel pointer.
> 
> So, please, stop this idea that somehow kernel developers can
> somehow spend infinite amounts of time solving lots and lots of
> bugs.

Sorry, that happens when using irony in a non-native language...

What I wanted to express:
Noone has unlimited time for kernel development.

> Russell King

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:55                     ` Theodore Tso
@ 2007-11-13 20:07                       ` Larry Finger
  0 siblings, 0 replies; 268+ messages in thread
From: Larry Finger @ 2007-11-13 20:07 UTC (permalink / raw)
  To: Theodore Tso, Larry Finger, Benoit Boissinot, Mark Lord,
	Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Theodore Tso wrote:
> 
> Heh. I hadn't enabled CONFIG_BCM43XX_DEBUG myself, but I just changed
> it for my next kernel build.  This is a slightly different issue,
> which is that sometimes _DEBUG options shouldn't be turned on by
> default (because they really trash performance and bloat log size),
> and sometimes they are painless to turn on and don't cost much.
> 
> If that is the case, I'd suggest removing the option and just making
> it compiled in by default with a run-time option to enable it.

I am taking your suggestion and will produce the necessary patches for ssb, b43 and b43legacy. As
bcm43xx is likely to be removed from 2.6.25, which is the earliest such a non-bug fix patch would be
accepted, I hope that your future distribution and testing kernels will include the debug option.

Thanks,

Larry

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:32             ` [BUG] New Kernel Bugs Russell King
@ 2007-11-13 20:13               ` Adrian Bunk
  2007-11-13 23:29                 ` Russell King
  2007-11-13 20:52               ` Andrew Morton
  1 sibling, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 20:13 UTC (permalink / raw)
  To: David Miller, akpm, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 07:32:19PM +0000, Russell King wrote:
>...
> There's another issue I want to raise concerning bugzilla.  We have the
> classic case of "not enough people reading bugzilla bugs" - which is one
> of the biggest problems with bugzilla.  Virtually no one in the ARM
> community looks for ARM bugs in bugzilla.
> 
> Let's not forget that it would be a waste of time for people to manually
> check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> into bugzilla that a weekly manual check by every maintainer would just
> return the same old boring results for months and months at a time.
>...

What about having all ARM bugs in Bugzilla by default assigned to 
linux-arm-kernel@lists.arm.linux.org.uk? [1]

> Russell King

cu
Adrian

[1] Either directly or through a pseudo address, but that's just a
    technical detail.

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:00                               ` Adrian Bunk
@ 2007-11-13 20:13                                 ` Mark Lord
  2007-11-13 21:20                                   ` Adrian Bunk
  2007-11-13 21:12                                 ` Alan Cox
  1 sibling, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-13 20:13 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 02:26:05PM -0500, Mark Lord wrote:
..
>> If you've been making significant updates to a driver/subsystem,
>> and people are reporting that it is now broken for them,
> 
> What are "significant updates"?
> 
> Sometimes one person makes one small patch and this patch contains
> a typo.
..

Then that person should double check their changes against
the problems reported, and re-convince themselves that the
breakage wasn't from those.  Simple. 

>> then it's your job to make it right.
> 
> We have some open drivers/ata/ regressions.
..

Yup, but they're more specific than just that entire subsystem,
and the maintainers are actively pursuing the problems.
Exactly what should be happening.

> I see some person named "Mark Lord" being responsible for 4 commits.
> 
> What pubishment do you plan for him if 2.6.24 ships with any libata 
> regressions?
..

If the code I'm touching breaks, then I'll fix it ASAP,
exactly what the users of that code might expect.

>> The reporters can help,
>> and many may even git-bisect or send patches.  
>> But you cannot *expect* or *insist* upon them doing your job.
> 
> Bullshit.
> 
> Bug fixing is not about finding someone to blame, it's about getting the 
> bug fixed.
..

It's not about blame, it's about paying attention to breakages in code that a
person claims to be supporting, and then doing their best to resolve the issues.

Again, if one has the time to actively write/modify code such that something breaks,
then that person should also make time to fix the breakages.

> The bug reporter is the person who can reproduce the problem, and if 
> it's a regression then bisecting is the natural way of getting nearer 
> at getting it fixed.
..
For the third time, no disagreement here.  git-bsect can help in many cases,
but not in all cases.  And it requires a great time commitment from somebody
who's system used to work and now doesn't work.  The person who broke it has
a fair bit of responsibility there, too.

cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:37               ` [BUG] New Kernel Bugs Russell King
@ 2007-11-13 20:18                 ` Mark Lord
  2007-11-13 21:33                   ` Jörn Engel
  2007-11-13 23:40                   ` Russell King
  0 siblings, 2 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 20:18 UTC (permalink / raw)
  To: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

Russell King wrote:
> On Tue, Nov 13, 2007 at 09:08:32AM -0500, Mark Lord wrote:
>> Ingo Molnar wrote:
>> ..
>>> This is all QA-101 that _cannot be argued against on a rational basis_, 
>>> it's just that these sorts of things have been largely ignored for 
>>> years, in favor of the all-too-easy "open source means many eyeballs and 
>>> that is our QA" answer, which is a _good_ answer but by far not the most 
>>> intelligent answer! Today "many eyeballs" is simply not good enough and 
>>> nature (and other OS projects) will route us around if we dont change.
>> ..
>>
>> QA-101 and "many eyeballs" are not at all in opposition.
>> The latter is how we find out about bugs on uncommon hardware,
>> and the former is what we need to track them and overall quality.
>>
>> A HUGE problem I have with current "efforts", is that once someone
>> reports a bug, the onus seems to be 99% on the *reporter* to find
>> the exact line of code or commit.  Ghad what a repressive method.
> 
> 99% on the reporter?  Is that why I always try to understand the
> reporters problem (*provided* it's in an area I know about) and come
> up with a patch to test a theory or fix the issue?
..

Same here.

I just find it weird that something can be known broken for several -rc*
kernels before I happen to install it, discover it's broken on my own machine,
and then I track it down, fix it, and submit the patch, generally all within a
couple of hours.  Where the heck was the dude(ess) that broke it ??  AWOL.

And when I receive hostility from the "maintainers" of said code for fixing
their bugs, well.. that really motivates me to continue reporting new ones..

> I'm _less_ inclined to provide such a "service" for lazy maintainers
> who've moved off into new and wonderfully exciting technologies, to
> churn out more patches for me to merge (and eventually provide a free
> to them bug fixing service for.)
> 
> That's "less" inclined, not "won't".
> 


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 19:32             ` [BUG] New Kernel Bugs Russell King
  2007-11-13 20:13               ` Adrian Bunk
@ 2007-11-13 20:52               ` Andrew Morton
  2007-11-13 22:18                 ` Russell King
  1 sibling, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 20:52 UTC (permalink / raw)
  To: Russell King
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, 13 Nov 2007 19:32:19 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:

> There's another issue I want to raise concerning bugzilla.  We have the
> classic case of "not enough people reading bugzilla bugs" - which is one
> of the biggest problems with bugzilla.  Virtually no one in the ARM
> community looks for ARM bugs in bugzilla.

Nor should they.

> Let's not forget that it would be a waste of time for people to manually
> check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> into bugzilla that a weekly manual check by every maintainer would just
> return the same old boring results for months and months at a time.

I screen all bugzilla reports.  100% of them.

- I'll try to establish whether it is a regression

- I'll solicit any extra information which I believe the reveloper will need

- I'll ensure that an appropriate developer has seen the report

And yes, the number of arm-specific reports in there is very small.

> It would be far more productive if the ARM category was deleted from
> bugzilla and the few people who use bugzilla reported their bugs on the
> mailing list.  We've a couple of thousand people on the ARM kernel
> mailing list at the moment - that's 3 orders of magnitude more of eyes
> than look at bugzilla.

Is that linux-arm-kernel@lists.arm.linux.org.uk?

If so, MANITAINERS claims that it is subscribers-only.  That would cause
some bug reporters to give up and go away.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:00               ` Christian Kujau
@ 2007-11-13 21:04                 ` Andrew Morton
  2007-11-13 16:56                   ` Nick Piggin
                                     ` (2 more replies)
  0 siblings, 3 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 21:04 UTC (permalink / raw)
  To: Christian Kujau; +Cc: linux-kernel, torvalds

On Tue, 13 Nov 2007 21:00:30 +0100 (CET) Christian Kujau <lists@nerdbynature.de> wrote:

> On Tue, 13 Nov 2007, Andrew Morton wrote:
> > I think that we're fairly good about working the regressions in
> > Adrian/Michal/Rafael's lists but once Linus releases 2.6.x we tend to let
> > the unsolved ones slide, and we don't pay as much attention to the
> > regressions which 2.6.x testers report.
> 
> Can't we wait until all regressions[0] are fixed before releasing a new 
> 2.6.x? I'd consider regressions a *literal* show stopper, and with this 
> policy they just have be fixed, nothing would "slide"...
> 

Problem is that everyone would then sit around pumping shiny new features
into their trees waiting until someone else fixes the regressions.

There are a number of process things we _could_ do.  Like

- have bugfix-only kernel releases

- Just refuse to merge any non-bugfix patches for a subsystem when it is
  determined that the subsystem has "too many" regressions.

- Create an "if you added a regression, you should fix some other bug
  too" rule.

- probably other stuff.

But we can't/shouldn't do any of that until it is generally agreed that we
have a problem and that the problem is of sufficient magnitude that process
changes are needed to address it.  We aren't at that stage yet.


Here's an important point: developers have a fixed amount of development
time.  They spend some of that time fixing bugs and the rest of that time
on <otherstuff>.  And while one could cook up all sorts of wonderful
process changes, they all would be aimed at a single thing: shifting some
of the developers' time away from <otherstuff> and onto bugfixing.

At this stage the only tool which is being deployed to attempt to bring
about that reprioritisation is suasion.  aka "lkml flamewar".


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:00                               ` Adrian Bunk
  2007-11-13 20:13                                 ` Mark Lord
@ 2007-11-13 21:12                                 ` Alan Cox
  2007-11-14  0:52                                   ` Chuck Ebbert
  1 sibling, 1 reply; 268+ messages in thread
From: Alan Cox @ 2007-11-13 21:12 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Mark Lord, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

> Bug fixing is not about finding someone to blame, it's about getting the 
> bug fixed.

Partly - its also about understanding why the bug occurred and making it
not happen again.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:13                                 ` Mark Lord
@ 2007-11-13 21:20                                   ` Adrian Bunk
  0 siblings, 0 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 21:20 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue, Nov 13, 2007 at 03:13:46PM -0500, Mark Lord wrote:
> Adrian Bunk wrote:
>> On Tue, Nov 13, 2007 at 02:26:05PM -0500, Mark Lord wrote:
> ..
>>> If you've been making significant updates to a driver/subsystem,
>>> and people are reporting that it is now broken for them,
>>
>> What are "significant updates"?
>>
>> Sometimes one person makes one small patch and this patch contains
>> a typo.
> ..
>
> Then that person should double check their changes against
> the problems reported, and re-convince themselves that the
> breakage wasn't from those.  Simple. 

Simple?

Everything you have in mind with "should double check their changes" is 
simply not realistic with dozens of known unfixed regressions within 
more than half a million changed or new lines of code written by more 
than 800 people - all numbers only counted since 2.6.23.

>...
>>> The reporters can help,
>>> and many may even git-bisect or send patches.  But you cannot *expect* or 
>>> *insist* upon them doing your job.
>>
>> Bullshit.
>>
>> Bug fixing is not about finding someone to blame, it's about getting the 
>> bug fixed.
> ..
>
> It's not about blame, it's about paying attention to breakages in code that a
> person claims to be supporting, and then doing their best to resolve the issues.

Maintainers are just humans with limited time. 

You were the one who suggested to "distribute code maintainership", 
so you should explain how to find the additional maintainers.

> Again, if one has the time to actively write/modify code such that something breaks,
> then that person should also make time to fix the breakages.

code writer != subsystem maintainer

And git-bisect is the tool that tells you who broke it.

>> The bug reporter is the person who can reproduce the problem, and if it's 
>> a regression then bisecting is the natural way of getting nearer at 
>> getting it fixed.
> ..
> For the third time, no disagreement here.  git-bsect can help in many cases,
> but not in all cases.  And it requires a great time commitment from somebody
> who's system used to work and now doesn't work.  The person who broke it has
> a fair bit of responsibility there, too.

git-bisect can help only for regressions, and it can help for most 
regressions.

And you shouldn't try to make a problem out of something that isn't a 
problem:

Bug submitters are either volunteers who test -rc or even -git or -mm 
kernels for finding bugs or people who want a problem they experience 
fixed.

In both cases the submitters are usually willing to invest some time for 
helping to get the bug fixed.

> cheers

cu
Adrian

--

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:18                 ` Mark Lord
@ 2007-11-13 21:33                   ` Jörn Engel
  2007-11-13 21:56                     ` Andrew Morton
  2007-11-13 22:29                     ` Mark Lord
  2007-11-13 23:40                   ` Russell King
  1 sibling, 2 replies; 268+ messages in thread
From: Jörn Engel @ 2007-11-13 21:33 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

On Tue, 13 November 2007 15:18:07 -0500, Mark Lord wrote:
> 
> I just find it weird that something can be known broken for several -rc*
> kernels before I happen to install it, discover it's broken on my own 
> machine,
> and then I track it down, fix it, and submit the patch, generally all 
> within a
> couple of hours.  Where the heck was the dude(ess) that broke it ??  AWOL.
> 
> And when I receive hostility from the "maintainers" of said code for fixing
> their bugs, well.. that really motivates me to continue reporting new ones..

Given a decent bug report, I agree that having the bug not looked at is
shameful.  But what can a developer do if a bug report effectively reads
"there is some bug somewhere in recent kernels"?  How can I know that in
this particular case it is my bug that I introduced?  It could just as
easily be 50 other people and none of them are eager to debug it unless
they suspect it to be their bug.

This is a common problem and fairly unrelated to linux in general or the
kernel in particular.  Who is going to be the sucker that figures out
which developer the bug belongs to?  And I have yet to find a project,
commercial or opensource, where volunteers flock to become such a
sucker.

One option is to push this role to the bug reporter.  Another is to
strong-arm some developers into this role, by whatever means.  A third
would be for $LARGE_COMPANY to hire some people.  If you have a better
idea or would volunteer your time, I'd be grateful.  Simply blaming one
side, whether bug reporter or a random developer, for not being the
sucker doesn't help anyone.

Jörn

-- 
Joern's library part 2:
http://www.art.net/~hopkins/Don/unix-haters/tirix/embarrassing-memo.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:04                 ` Andrew Morton
  2007-11-13 16:56                   ` Nick Piggin
@ 2007-11-13 21:37                   ` Adrian Bunk
  2007-11-13 21:56                   ` Christian Kujau
  2 siblings, 0 replies; 268+ messages in thread
From: Adrian Bunk @ 2007-11-13 21:37 UTC (permalink / raw)
  To: Andrew Morton; +Cc: Christian Kujau, linux-kernel, torvalds

On Tue, Nov 13, 2007 at 01:04:11PM -0800, Andrew Morton wrote:
>...
> Here's an important point: developers have a fixed amount of development
> time.  They spend some of that time fixing bugs and the rest of that time
> on <otherstuff>.  And while one could cook up all sorts of wonderful
> process changes, they all would be aimed at a single thing: shifting some
> of the developers' time away from <otherstuff> and onto bugfixing.
>...

There is another possible solution:
Finding more maintainers.

The problem seems to be that there are many people who want to write 
drivers for cool shiny new hardware, but not many people willing to
learn to know and maintain existing code.

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:04                 ` Andrew Morton
  2007-11-13 16:56                   ` Nick Piggin
  2007-11-13 21:37                   ` Adrian Bunk
@ 2007-11-13 21:56                   ` Christian Kujau
  2007-11-15  4:07                     ` Bron Gondwana
  2 siblings, 1 reply; 268+ messages in thread
From: Christian Kujau @ 2007-11-13 21:56 UTC (permalink / raw)
  To: Andrew Morton; +Cc: linux-kernel, torvalds

On Tue, 13 Nov 2007, Andrew Morton wrote:
> There are a number of process things we _could_ do.  Like
> - have bugfix-only kernel releases

Adrian Bunk does (did?) this with 2.6.16.x, although it always seemed to 
me like an unrewarded one man show. AFAIK not even the big distros are 
begging for bugfix-only versions, as they too want to have (sell) new 
features. Mission critical systems might want to require such versions, 
but I guess they're using heavily customized trees anyway.

> - Just refuse to merge any non-bugfix patches for a subsystem when it is
>  determined that the subsystem has "too many" regressions.

Hm, that's what I had in mind. Has this been tried already?

> - Create an "if you added a regression, you should fix some other bug
>  too" rule.

Naah, I'm not really in favour of blaming someone. The kernel doesn't have 
SLA contracts (yet), so no need for giving out penalties :)

> But we can't/shouldn't do any of that until it is generally agreed that we
> have a problem and that the problem is of sufficient magnitude that process
> changes are needed to address it.  We aren't at that stage yet.

Keeping track of the (number of) regressions / bugs each release seems to 
be a good start, IMHO.

> process changes, they all would be aimed at a single thing: shifting some
> of the developers' time away from <otherstuff> and onto bugfixing.

True. Implementing "only bugfixes from now on" (i.e. a longer 
freeze-window) would perhaps speed up the shifting a bit: $developer can 
still do $otherstuff all day long, but it won't get merged anyway, because 
we're in "only bugfixes from now on"-mode.

> At this stage the only tool which is being deployed to attempt to bring
> about that reprioritisation is suasion.  aka "lkml flamewar".

True. But I just noticed that I have to distinguish between 
"flamewars" and "fierce discussions": if I'd imagine a room with ~50 
developers/bystanders brainstorming on a issue like this (at the same 
time, without the wonderful delay of writing/sending an email), it'd
feel much more uncomfortable.

Christian.
-- 
BOFH excuse #433:

error: one bad user found in front of screen

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:33                   ` Jörn Engel
@ 2007-11-13 21:56                     ` Andrew Morton
  2007-11-13 22:24                       ` Jörn Engel
  2007-11-13 22:29                     ` Mark Lord
  1 sibling, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 21:56 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Ingo Molnar, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	David Miller

On Tue, 13 Nov 2007 22:33:58 +0100 Jörn Engel <joern@logfs.org> wrote:

> On Tue, 13 November 2007 15:18:07 -0500, Mark Lord wrote:
> > 
> > I just find it weird that something can be known broken for several -rc*
> > kernels before I happen to install it, discover it's broken on my own 
> > machine,
> > and then I track it down, fix it, and submit the patch, generally all 
> > within a
> > couple of hours.  Where the heck was the dude(ess) that broke it ??  AWOL.
> > 
> > And when I receive hostility from the "maintainers" of said code for fixing
> > their bugs, well.. that really motivates me to continue reporting new ones..
> 
> Given a decent bug report, I agree that having the bug not looked at is
> shameful.  But what can a developer do if a bug report effectively reads
> "there is some bug somewhere in recent kernels"?  How can I know that in
> this particular case it is my bug that I introduced?  It could just as
> easily be 50 other people and none of them are eager to debug it unless
> they suspect it to be their bug.

It's relatively common that a regression in subsystem A will manifest as a
failure in subsystem B, and the report initially lands on the desk of the
subsystem B developers.

But that's OK.  The subsystem B people are the ones with the expertise to
be able to work out where the bug resides and to help the subsystem A
people understand what went wrong.

Alas, sometimes the B people will just roll eyes and do nothing because
they know the problem wasn't in their code.  Sometimes.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:50                     ` Romano Giannetti
@ 2007-11-13 22:03                       ` Frans Pop
  0 siblings, 0 replies; 268+ messages in thread
From: Frans Pop @ 2007-11-13 22:03 UTC (permalink / raw)
  To: Romano Giannetti
  Cc: akpm, alsa-devel, bugme-daemon, bunk, cate, davem, liml,
	linux-ide, linux-input, linux-kernel, linux-pcmcia, mingo,
	netdev, protasnb, ray-lk

Romano Giannetti wrote:
> This was what I did in my (in the end almost successful) bisecting when
> trying to find the mmc problem (see the thread named "2.6.24-rc1 eat my
> SD card"). This is true in theory, but it has some problem. The "this
> commit does not compile is the easiest and in man git-bisect it's
> explained how to solve it. The changes in .config options, added or
> removed, are another problem when jumping back and forth from version.
> 
> The main problem I had, and that stopped me to arrive to a definite is
> this situation:
[...] 
> (d was the series to change drivers to use sg helpers, and g was a "fix
> fallout from sg helpers" patch). Now I have a series of kernels (d, e,
> f) that did not work at all and so I cannot mark them good or bad. With
> the number of patches added in the free-for-all week, this is a very
> probable scenario. There is a way out from this using bisect?

I think there are three strategies you can use in this case:
- create a kernel config that is as simple as possible, but still supports
  your hardware and reproduces your problem; a simpler config will often
  avoid compilation issues in parts of the kernel that you're not using
  anyway and has the benefit of speeding up the compiles too

- if you know/suspect in what part of the tree the bug is, first limit the
  bisection to that; you will have to verify that you did indeed find the
  correct (broken) change by doing a compile for the "last good commit + 1"

- if you find a broken commit, use 'git-reset --hard' to try to jump past
  the bad set of commits, but of course that does not help in the case:
    g version-bad
    f unrelated bug corrected
    e
    d the broken commit that caused your problem
    c
    b unrelated bug that breaks compilation or system introduced
    a version-good
  in that case the best you can reasonably be expected to do is report that
  you narrowed it down to "between a and g" and leave the rest to the
  developers

Cheers,
FJP

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:54                         ` Mark Lord
@ 2007-11-13 22:09                           ` Rafael J. Wysocki
  2007-11-14 14:30                           ` Ingo Molnar
  1 sibling, 0 replies; 268+ messages in thread
From: Rafael J. Wysocki @ 2007-11-13 22:09 UTC (permalink / raw)
  To: Mark Lord
  Cc: Matthew Wilcox, Ingo Molnar, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	Andrew Morton, David Miller

On Tuesday, 13 of November 2007, Mark Lord wrote:
> Matthew Wilcox wrote:
> > On Tue, Nov 13, 2007 at 01:43:53PM -0500, Mark Lord wrote:
> >
> >> mkdir t
> >> cd t
> >> git clone 
> >> git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
> >> (wait half an hour)
> >> /usr/bin/du -s linux-2.6
> >> 522732  linux-2.6
> > 
> > You're assuming that everything in linux-2.6 was downloaded; that's
> > not true.  Everything in linux-2.6/.git was downloaded; but then you do a
> > checkout which happens to approximately double the size of the linux-2.6
> > directory. 
> ..
> 
> Ah, I wondered why it took only half an hour to download.
> 
> ..
> > When you compare it to the 60MB tarballs that are published, it's really
> > not that bad.
> ..
> 
> The tarballs I download are only 45MB.

You clone the git repo once.  Afterwards, you only update it and that usually
doesn't take that much time and a little effort.

Greetings,
Rafael

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:52               ` Andrew Morton
@ 2007-11-13 22:18                 ` Russell King
  2007-11-13 22:32                   ` Andrew Morton
  2007-11-14  5:56                   ` [BUG] New Kernel Bugs Sam Ravnborg
  0 siblings, 2 replies; 268+ messages in thread
From: Russell King @ 2007-11-13 22:18 UTC (permalink / raw)
  To: Andrew Morton
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 12:52:22PM -0800, Andrew Morton wrote:
> On Tue, 13 Nov 2007 19:32:19 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > There's another issue I want to raise concerning bugzilla.  We have the
> > classic case of "not enough people reading bugzilla bugs" - which is one
> > of the biggest problems with bugzilla.  Virtually no one in the ARM
> > community looks for ARM bugs in bugzilla.
> 
> Nor should they.

So what you're saying is...

> > Let's not forget that it would be a waste of time for people to manually
> > check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> > into bugzilla that a weekly manual check by every maintainer would just
> > return the same old boring results for months and months at a time.
> 
> I screen all bugzilla reports.  100% of them.
> 
> - I'll try to establish whether it is a regression
> 
> - I'll solicit any extra information which I believe the reveloper will need
> 
> - I'll ensure that an appropriate developer has seen the report
> 
> And yes, the number of arm-specific reports in there is very small.

that just because you do this everyone in a select clique, who you include
me in, should be doing this as well.

No.  Thank.  You.

> > It would be far more productive if the ARM category was deleted from
> > bugzilla and the few people who use bugzilla reported their bugs on the
> > mailing list.  We've a couple of thousand people on the ARM kernel
> > mailing list at the moment - that's 3 orders of magnitude more of eyes
> > than look at bugzilla.
> 
> Is that linux-arm-kernel@lists.arm.linux.org.uk?

Yes.

> If so, MANITAINERS claims that it is subscribers-only.  That would cause
> some bug reporters to give up and go away.

Find some other mailing list; I'm not hosting *nor* am I willing to run a
non-subscribers only mailing list.  Period.  Not negotiable, so don't even
try to change my mind.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:56                     ` Andrew Morton
@ 2007-11-13 22:24                       ` Jörn Engel
  2007-11-13 22:43                         ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-11-13 22:24 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Jörn Engel, Mark Lord, Ingo Molnar, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, protasnb, linux-ide, bugme-daemon,
	linux-input, David Miller

On Tue, 13 November 2007 13:56:58 -0800, Andrew Morton wrote:
> 
> It's relatively common that a regression in subsystem A will manifest as a
> failure in subsystem B, and the report initially lands on the desk of the
> subsystem B developers.
> 
> But that's OK.  The subsystem B people are the ones with the expertise to
> be able to work out where the bug resides and to help the subsystem A
> people understand what went wrong.
> 
> Alas, sometimes the B people will just roll eyes and do nothing because
> they know the problem wasn't in their code.  Sometimes.

And sometimes the A people will ignore the B people after the root cause
has been worked out.  Do you have a good idea how to shame A into
action?  Should I put you on Cc:?  Right now I'm in the eye-rolling
phase.

Jörn

-- 
The cost of changing business rules is much more expensive for software
than for a secretaty.
-- unknown

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:33                   ` Jörn Engel
  2007-11-13 21:56                     ` Andrew Morton
@ 2007-11-13 22:29                     ` Mark Lord
  1 sibling, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 22:29 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Ingo Molnar, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

Jörn Engel wrote:
> On Tue, 13 November 2007 15:18:07 -0500, Mark Lord wrote:
>> I just find it weird that something can be known broken for several -rc*
>> kernels before I happen to install it, discover it's broken on my own machine,
>> and then I track it down, fix it, and submit the patch, generally all within a
>> couple of hours.  Where the heck was the dude(ess) that broke it ??  AWOL.
>>
>> And when I receive hostility from the "maintainers" of said code for fixing
>> their bugs, well.. that really motivates me to continue reporting new ones..
> 
> Given a decent bug report, I agree that having the bug not looked at is
> shameful.  But what can a developer do if a bug report effectively reads
> "there is some bug somewhere in recent kernels"?  How can I know that in
> this particular case it is my bug that I introduced?  It could just as
> easily be 50 other people and none of them are eager to debug it unless
> they suspect it to be their bug.
..

Most of the regressions we have are easily identifiable and not of the type
where there could "50 other people" touching the relevant code.  As a developer
(and former subsystem maintainer) I look hard at my own code when there's a
bug reported that could have come from recent updates there.  Usually there are
not that many updates to consider, and tracking it down is just a matter of
being willing to do so.

Of late, I've given up on other developers fixing the stuff they break on my
own machines, and I generally just dive into totally unfamiliar code, and find
and fix it myself.  Quite quickly, usually.  And the bugs are often very apparent
just from looking at the source code diffs (patches) from recent history in
the code that's not working.  This is not rocket science, and it doesn't require
a log2 download/rebuild/reboot process.

But yes, there are more difficult ones, like when my machine crashed yesterday
with some form of corruption showing up during JBD filesystem I/O.  That's one
where the problem isn't going to be obvious to anyone, and I don't actually
expect anyone to go looking for it right away.  If more such events happen,
then it will get more attention.

But things like broken drivers, in almost every case those are trivial
to track down and fix, even for people not familar with that specific code.

> This is a common problem and fairly unrelated to linux in general or the
> kernel in particular.  Who is going to be the sucker that figures out
> which developer the bug belongs to?  And I have yet to find a project,
> commercial or opensource, where volunteers flock to become such a
> sucker.
> 
> One option is to push this role to the bug reporter.  Another is to
> strong-arm some developers into this role, by whatever means.  A third
> would be for $LARGE_COMPANY to hire some people.  If you have a better
> idea or would volunteer your time, I'd be grateful.  Simply blaming one
> side, whether bug reporter or a random developer, for not being the
> sucker doesn't help anyone.
..

Nobody's blaming anyone here.  I'm just asking that developers here do more
like our Top Penguin does, and actually look at problems and try to understand
them and suggest fixes to try.  And not rely solely on the git-bisect crutch.
It's a good crutch, provided the reporter is a kernel developer, or has a lot
of time on their hands.  But we debugged Linux here for a long time without it.

And I already volunteer my time here, thanks, BIG TIME, since 1992 or so.

Cheers


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:18                 ` Russell King
@ 2007-11-13 22:32                   ` Andrew Morton
  2007-11-13 23:09                     ` Russell King
  2007-11-14  1:55                     ` David Miller
  2007-11-14  5:56                   ` [BUG] New Kernel Bugs Sam Ravnborg
  1 sibling, 2 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 22:32 UTC (permalink / raw)
  To: Russell King
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, 13 Nov 2007 22:18:01 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:

> On Tue, Nov 13, 2007 at 12:52:22PM -0800, Andrew Morton wrote:
> > On Tue, 13 Nov 2007 19:32:19 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > > There's another issue I want to raise concerning bugzilla.  We have the
> > > classic case of "not enough people reading bugzilla bugs" - which is one
> > > of the biggest problems with bugzilla.  Virtually no one in the ARM
> > > community looks for ARM bugs in bugzilla.
> > 
> > Nor should they.
> 
> So what you're saying is...
> 
> > > Let's not forget that it would be a waste of time for people to manually
> > > check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> > > into bugzilla that a weekly manual check by every maintainer would just
> > > return the same old boring results for months and months at a time.
> > 
> > I screen all bugzilla reports.  100% of them.
> > 
> > - I'll try to establish whether it is a regression
> > 
> > - I'll solicit any extra information which I believe the reveloper will need
> > 
> > - I'll ensure that an appropriate developer has seen the report
> > 
> > And yes, the number of arm-specific reports in there is very small.
> 
> that just because you do this everyone in a select clique, who you include
> me in, should be doing this as well.
> 
> No.  Thank.  You.

No, I don't mean that at all and this was very plainly obviously from my very
clearly written email.  Let me try again.

No, no subsystem developer needs to monitor new bugzilla reports.  This is
because *I do it for them*.  I will actively make them aware of new reports
which I believe are legitimate and which contain sufficient information for
them to be able to take further action.

> > > It would be far more productive if the ARM category was deleted from
> > > bugzilla and the few people who use bugzilla reported their bugs on the
> > > mailing list.  We've a couple of thousand people on the ARM kernel
> > > mailing list at the moment - that's 3 orders of magnitude more of eyes
> > > than look at bugzilla.
> > 
> > Is that linux-arm-kernel@lists.arm.linux.org.uk?
> 
> Yes.
> 
> > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > some bug reporters to give up and go away.
> 
> Find some other mailing list; I'm not hosting *nor* am I willing to run a
> non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> try to change my mind.

Making a list subscribers-only will cause some bug reports to be lost.

Tradeoffs are involved, against which decisions must be made.  You have
made yours.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:25         ` Alan Cox
@ 2007-11-13 22:34           ` Russell King
  2007-11-15 20:16             ` Ben Dooks
  0 siblings, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 22:34 UTC (permalink / raw)
  To: Alan Cox
  Cc: Thomas Gleixner, Mark Lord, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, Natalie Protasevich, linux-ide, bugme-daemon,
	linux-input, Andrew Morton

On Tue, Nov 13, 2007 at 06:25:16PM +0000, Alan Cox wrote:
> > Given the wide range of ARM platforms today, it is utterly idiotic to
> > expect a single person to be able to provide responses for all ARM bugs.
> > I for one wish I'd never *VOLUNTEERED* to be a part of the kernel
> > bugzilla, and really *WISH* I could pull out of that function.
> 
> You can. Perhaps that bugzilla needs to point to some kind of
> arm-maintainers@vger.kernel.org list for the various ARM platform
> maintainers ?

That might work - though it would be hard to get all the platform
maintainers to be signed up to yet another mailing list, I'm sure
sufficient would do.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:24                       ` Jörn Engel
@ 2007-11-13 22:43                         ` Andrew Morton
  0 siblings, 0 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 22:43 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Ingo Molnar, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	David Miller

On Tue, 13 Nov 2007 23:24:14 +0100 Jörn Engel <joern@logfs.org> wrote:

> On Tue, 13 November 2007 13:56:58 -0800, Andrew Morton wrote:
> > 
> > It's relatively common that a regression in subsystem A will manifest as a
> > failure in subsystem B, and the report initially lands on the desk of the
> > subsystem B developers.
> > 
> > But that's OK.  The subsystem B people are the ones with the expertise to
> > be able to work out where the bug resides and to help the subsystem A
> > people understand what went wrong.
> > 
> > Alas, sometimes the B people will just roll eyes and do nothing because
> > they know the problem wasn't in their code.  Sometimes.
> 
> And sometimes the A people will ignore the B people after the root cause
> has been worked out.  Do you have a good idea how to shame A into
> action?  Should I put you on Cc:?  Right now I'm in the eye-rolling
> phase.
> 

Well, that's the problem, isn't it?

The best I can come up with is to suggest that all the info be captured in
a bugzilla report so that at least it doesn't get forgotten about.

I suppose that other options are

a) try to fix it yourself.  I'll take the patch and as long as we make a
   big enough mess of it, someone who knows what they're doing might fix it
   for real.

b) If it was a regression, identify the offending commit and we'll just
   revert it.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:54       ` [BUG] New Kernel Bugs Mark Lord
@ 2007-11-13 22:46         ` Thomas Gleixner
  2007-11-13 23:37           ` Mark Lord
  0 siblings, 1 reply; 268+ messages in thread
From: Thomas Gleixner @ 2007-11-13 22:46 UTC (permalink / raw)
  To: Mark Lord
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007, Mark Lord wrote:

> Thomas Gleixner wrote:
> > On Tue, 13 Nov 2007, Mark Lord wrote:
> > 
> > > > Andrew Morton wrote:
> > > > > > On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
> > > > > > <protasnb@gmail.com> wrote:
> > > > ..
> > > > > > > > with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23
> > > > > doesn't
> > > > > > > > boot (ARM, Timer)
> > > > > > > > http://bugzilla.kernel.org/show_bug.cgi?id=9229
> > > > > > > > Kernel: 2.6.23
> > > > > > > > No response from developers
> > > > ..
> > 
> > The bug report is bogus. ARM has no CONFIG_HPET_TIMER.  
> > > > Note:  that same bug exists/existed on i386 back when NO_HZ was
> > > > introduced (2.6.21?).  I still see it from time to time on my Quad core
> > > > system (very rare), but not any more on my Duo notebook where it used
> > > > to happen about 1 in n boots (n < 10).
> > > > > AFAICT no fix was ever released for it.
> > 
> > Hmm, at which point does the boot stop ? 
> ..
> 
> Just as it prints out these messages, sometimes one of them,
> sometimes both (or all four on the quad core):
> 
> kernel: switched to high resolution mode on cpu 1
> kernel: switched to high resolution mode on cpu 0 

It's completely dead afterwards ?

     tglx

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:32                   ` Andrew Morton
@ 2007-11-13 23:09                     ` Russell King
  2007-11-13 23:17                       ` Andrew Morton
  2007-11-14  1:55                     ` David Miller
  1 sibling, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 23:09 UTC (permalink / raw)
  To: Andrew Morton
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 02:32:01PM -0800, Andrew Morton wrote:
> On Tue, 13 Nov 2007 22:18:01 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > On Tue, Nov 13, 2007 at 12:52:22PM -0800, Andrew Morton wrote:
> > > On Tue, 13 Nov 2007 19:32:19 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > > > There's another issue I want to raise concerning bugzilla.  We have the
> > > > classic case of "not enough people reading bugzilla bugs" - which is one
> > > > of the biggest problems with bugzilla.  Virtually no one in the ARM
> > > > community looks for ARM bugs in bugzilla.
> > > 
> > > Nor should they.
> > 
> > So what you're saying is...
> > 
> > > > Let's not forget that it would be a waste of time for people to manually
> > > > check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> > > > into bugzilla that a weekly manual check by every maintainer would just
> > > > return the same old boring results for months and months at a time.
> > > 
> > > I screen all bugzilla reports.  100% of them.
> > > 
> > > - I'll try to establish whether it is a regression
> > > 
> > > - I'll solicit any extra information which I believe the reveloper will need
> > > 
> > > - I'll ensure that an appropriate developer has seen the report
> > > 
> > > And yes, the number of arm-specific reports in there is very small.
> > 
> > that just because you do this everyone in a select clique, who you include
> > me in, should be doing this as well.
> > 
> > No.  Thank.  You.
> 
> No, I don't mean that at all and this was very plainly obviously from my very
> clearly written email.  Let me try again.

If you screen all bugzilla reports then you'll know that bug #9356 arrived
at about 1400 GMT yesterday.  It's hardly surprising then that your utterly
crappy responses to Natalie's message (which, incidentally, wasn't copied
to me) sent within 24 hours of that report cause *great* annoyance.

> No, no subsystem developer needs to monitor new bugzilla reports.  This is
> because *I do it for them*.  I will actively make them aware of new reports
> which I believe are legitimate and which contain sufficient information for
> them to be able to take further action.

On the whole you do an excellent job with feeding the bug reports to
people, and while I recognise that you're only human, things do
occasionally go wrong.  For instance, sending clearly marked Samsung
S3C bugs to me rather than Ben Dooks (who's in MAINTAINERS for those
platforms.)

> > > > It would be far more productive if the ARM category was deleted from
> > > > bugzilla and the few people who use bugzilla reported their bugs on the
> > > > mailing list.  We've a couple of thousand people on the ARM kernel
> > > > mailing list at the moment - that's 3 orders of magnitude more of eyes
> > > > than look at bugzilla.
> > > 
> > > Is that linux-arm-kernel@lists.arm.linux.org.uk?
> > 
> > Yes.
> > 
> > > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > > some bug reporters to give up and go away.
> > 
> > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > try to change my mind.
> 
> Making a list subscribers-only will cause some bug reports to be lost.
> 
> Tradeoffs are involved, against which decisions must be made.  You have
> made yours.

So how are they lost when they're held in a moderation queue and are
either accepted, a useful response given to the original poster, or
are forwarded to someone who can deal with the issue.

I don't think "subscribers only" describes my lists - we don't devnull
stuff just because the poster is not a subscriber.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 23:09                     ` Russell King
@ 2007-11-13 23:17                       ` Andrew Morton
  0 siblings, 0 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 23:17 UTC (permalink / raw)
  To: Russell King
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, 13 Nov 2007 23:09:37 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:

> On Tue, Nov 13, 2007 at 02:32:01PM -0800, Andrew Morton wrote:
> > On Tue, 13 Nov 2007 22:18:01 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > > On Tue, Nov 13, 2007 at 12:52:22PM -0800, Andrew Morton wrote:
> > > > On Tue, 13 Nov 2007 19:32:19 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > No, I don't mean that at all and this was very plainly obviously from my very
> > clearly written email.  Let me try again.
> 
> If you screen all bugzilla reports then you'll know that bug #9356 arrived
> at about 1400 GMT yesterday.  It's hardly surprising then that your utterly
> crappy responses to Natalie's message (which, incidentally, wasn't copied
> to me) sent within 24 hours of that report cause *great* annoyance.
> 
> > No, no subsystem developer needs to monitor new bugzilla reports.  This is
> > because *I do it for them*.  I will actively make them aware of new reports
> > which I believe are legitimate and which contain sufficient information for
> > them to be able to take further action.
> 
> On the whole you do an excellent job with feeding the bug reports to
> people, and while I recognise that you're only human, things do
> occasionally go wrong.  For instance, sending clearly marked Samsung
> S3C bugs to me rather than Ben Dooks (who's in MAINTAINERS for those
> platforms.)


Well whatever, sorry.  But this is in the noise floor.  Point is: many bug
reports aren't being attended to.


> > > > > It would be far more productive if the ARM category was deleted from
> > > > > bugzilla and the few people who use bugzilla reported their bugs on the
> > > > > mailing list.  We've a couple of thousand people on the ARM kernel
> > > > > mailing list at the moment - that's 3 orders of magnitude more of eyes
> > > > > than look at bugzilla.
> > > > 
> > > > Is that linux-arm-kernel@lists.arm.linux.org.uk?
> > > 
> > > Yes.
> > > 
> > > > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > > > some bug reporters to give up and go away.
> > > 
> > > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > > try to change my mind.
> > 
> > Making a list subscribers-only will cause some bug reports to be lost.
> > 
> > Tradeoffs are involved, against which decisions must be made.  You have
> > made yours.
> 
> So how are they lost when they're held in a moderation queue and are
> either accepted, a useful response given to the original poster, or
> are forwarded to someone who can deal with the issue.
> 
> I don't think "subscribers only" describes my lists - we don't devnull
> stuff just because the poster is not a subscriber.

Oh, OK, as long as there really is a human paying attention to those things
then that's fine.  When one is on the sending end of these things one never
knows how long it will take, not whether it will even happen.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:13               ` Adrian Bunk
@ 2007-11-13 23:29                 ` Russell King
  2007-11-13 23:38                   ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 23:29 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: David Miller, akpm, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 09:13:19PM +0100, Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 07:32:19PM +0000, Russell King wrote:
> >...
> > There's another issue I want to raise concerning bugzilla.  We have the
> > classic case of "not enough people reading bugzilla bugs" - which is one
> > of the biggest problems with bugzilla.  Virtually no one in the ARM
> > community looks for ARM bugs in bugzilla.
> > 
> > Let's not forget that it would be a waste of time for people to manually
> > check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> > into bugzilla that a weekly manual check by every maintainer would just
> > return the same old boring results for months and months at a time.
> >...
> 
> What about having all ARM bugs in Bugzilla by default assigned to 
> linux-arm-kernel@lists.arm.linux.org.uk? [1]

That would also work, probably much better than setting up yet another
list.

My experience of trying to get mbligh to do this when I stopped looking
after PCMCIA stuff was *extremely* painful.  Wonder if it's become any
easier of late?

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:46         ` Thomas Gleixner
@ 2007-11-13 23:37           ` Mark Lord
  0 siblings, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-13 23:37 UTC (permalink / raw)
  To: Thomas Gleixner
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

Thomas Gleixner wrote:
> On Tue, 13 Nov 2007, Mark Lord wrote:
> 
>> Thomas Gleixner wrote:
>>> On Tue, 13 Nov 2007, Mark Lord wrote:
>>>
>>>>> Andrew Morton wrote:
>>>>>>> On Mon, 12 Nov 2007 22:42:32 -0800 "Natalie Protasevich"
>>>>>>> <protasnb@gmail.com> wrote:
>>>>> ..
>>>>>>>>> with CONFIG_NO_HZ and/or CONFIG_HPET_TIMER set kernel 2.6.23
>>>>>> doesn't
>>>>>>>>> boot (ARM, Timer)
>>>>>>>>> http://bugzilla.kernel.org/show_bug.cgi?id=9229
>>>>>>>>> Kernel: 2.6.23
>>>>>>>>> No response from developers
>>>>> ..
>>> The bug report is bogus. ARM has no CONFIG_HPET_TIMER.  
>>>>> Note:  that same bug exists/existed on i386 back when NO_HZ was
>>>>> introduced (2.6.21?).  I still see it from time to time on my Quad core
>>>>> system (very rare), but not any more on my Duo notebook where it used
>>>>> to happen about 1 in n boots (n < 10).
>>>>>> AFAICT no fix was ever released for it.
>>> Hmm, at which point does the boot stop ? 
>> ..
>>
>> Just as it prints out these messages, sometimes one of them,
>> sometimes both (or all four on the quad core):
>>
>> kernel: switched to high resolution mode on cpu 1
>> kernel: switched to high resolution mode on cpu 0 
> 
> It's completely dead afterwards ?

Yeah.  No magic sysrq key or anything.
There's gotta be a race somewhere that's causing it,
but it's not obvious where to look for it.

My regular 2-core notebook no longer suffers from it,
and subtle .config changes used to make it come and go
back when it first appeared.

The quad-core has only done it twice on me thus far.

Tracking this one down looks tricky.  It might require some early lockup
detection code to be tailor made or something.

Cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 23:29                 ` Russell King
@ 2007-11-13 23:38                   ` Andrew Morton
  0 siblings, 0 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-13 23:38 UTC (permalink / raw)
  To: Russell King
  Cc: Adrian Bunk, David Miller, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input

On Tue, 13 Nov 2007 23:29:54 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:

> On Tue, Nov 13, 2007 at 09:13:19PM +0100, Adrian Bunk wrote:
> > On Tue, Nov 13, 2007 at 07:32:19PM +0000, Russell King wrote:
> > >...
> > > There's another issue I want to raise concerning bugzilla.  We have the
> > > classic case of "not enough people reading bugzilla bugs" - which is one
> > > of the biggest problems with bugzilla.  Virtually no one in the ARM
> > > community looks for ARM bugs in bugzilla.
> > > 
> > > Let's not forget that it would be a waste of time for people to manually
> > > check bugzilla for ARM bugs.  There's soo few people reporting ARM bugs
> > > into bugzilla that a weekly manual check by every maintainer would just
> > > return the same old boring results for months and months at a time.
> > >...
> > 
> > What about having all ARM bugs in Bugzilla by default assigned to 
> > linux-arm-kernel@lists.arm.linux.org.uk? [1]
> 
> That would also work, probably much better than setting up yet another
> list.

cpufreq (at least) does it this way.  I don't know how well it is turning
out in practice.

It's useful if the initial report makes it clear (ie; to me) that the report
has already gone to a mailing list so I don't go and forward a duplicate.

But there are so few arm reports in bugzilla that this is all rather moot.

> My experience of trying to get mbligh to do this when I stopped looking
> after PCMCIA stuff was *extremely* painful.  Wonder if it's become any
> easier of late?

He's a bad, bad man ;)

But he's been turning these things around pretty rapidly lately.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 20:18                 ` Mark Lord
  2007-11-13 21:33                   ` Jörn Engel
@ 2007-11-13 23:40                   ` Russell King
  2007-11-14  1:56                     ` David Miller
  1 sibling, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-13 23:40 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller

On Tue, Nov 13, 2007 at 03:18:07PM -0500, Mark Lord wrote:
> Russell King wrote:
> > On Tue, Nov 13, 2007 at 09:08:32AM -0500, Mark Lord wrote:
> >> Ingo Molnar wrote:
> >> ..
> >>> This is all QA-101 that _cannot be argued against on a rational basis_, 
> >>> it's just that these sorts of things have been largely ignored for 
> >>> years, in favor of the all-too-easy "open source means many eyeballs and 
> >>> that is our QA" answer, which is a _good_ answer but by far not the most 
> >>> intelligent answer! Today "many eyeballs" is simply not good enough and 
> >>> nature (and other OS projects) will route us around if we dont change.
> >> ..
> >>
> >> QA-101 and "many eyeballs" are not at all in opposition.
> >> The latter is how we find out about bugs on uncommon hardware,
> >> and the former is what we need to track them and overall quality.
> >>
> >> A HUGE problem I have with current "efforts", is that once someone
> >> reports a bug, the onus seems to be 99% on the *reporter* to find
> >> the exact line of code or commit.  Ghad what a repressive method.
> > 
> > 99% on the reporter?  Is that why I always try to understand the
> > reporters problem (*provided* it's in an area I know about) and come
> > up with a patch to test a theory or fix the issue?
> ..
> 
> Same here.
> 
> I just find it weird that something can be known broken for several -rc*
> kernels before I happen to install it, discover it's broken on my own machine,
> and then I track it down, fix it, and submit the patch, generally all within a
> couple of hours.  Where the heck was the dude(ess) that broke it ??  AWOL.

Same thing can be said for compile breakages as well.  Looking at the
latest kautobuild output:

ARM ep93xx defconfig has been broken since 2.6.23-git1 due to:

drivers/net/arm/ep93xx_eth.c:420: error: implicit declaration of function '__netif_rx_schedule_prep'

caused by: [NET]: Make NAPI polling independent of struct net_device objects.

ARM netx defconfig has been broken since 2.6.23-git1 due to:

drivers/net/netx-eth.c: In function 'netx_eth_hard_start_xmit':
drivers/net/netx-eth.c:131: error: 'dev' undeclared (first use in this function)
drivers/net/netx-eth.c:131: error: (Each undeclared identifier is reported only once
drivers/net/netx-eth.c:131: error: for each function it appears in.)
drivers/net/netx-eth.c: In function 'netx_eth_receive':
drivers/net/netx-eth.c:158: error: 'dev' undeclared (first use in this function)

caused by: [NET] drivers/net: statistics cleanup #1 -- save memory and shrink code

Haven't got a report for either of those, but Kautobuild lets people
know if folk can be bothered to subscribe to its mailing list and/or
look at the site occasionally.

I suspect the maintainers of the above drivers aren't aware that their
drivers are broken.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 14:08             ` Mark Lord
                                 ` (3 preceding siblings ...)
  2007-11-13 19:37               ` [BUG] New Kernel Bugs Russell King
@ 2007-11-14  0:34               ` Denys Vlasenko
  2007-11-15  3:06                 ` Neil Brown
  4 siblings, 1 reply; 268+ messages in thread
From: Denys Vlasenko @ 2007-11-14  0:34 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tuesday 13 November 2007 07:08, Mark Lord wrote:
> Ingo Molnar wrote:
> ..
>
> > This is all QA-101 that _cannot be argued against on a rational basis_,
> > it's just that these sorts of things have been largely ignored for
> > years, in favor of the all-too-easy "open source means many eyeballs and
> > that is our QA" answer, which is a _good_ answer but by far not the most
> > intelligent answer! Today "many eyeballs" is simply not good enough and
> > nature (and other OS projects) will route us around if we dont change.
>
> ..
>
> QA-101 and "many eyeballs" are not at all in opposition.
> The latter is how we find out about bugs on uncommon hardware,
> and the former is what we need to track them and overall quality.
>
> A HUGE problem I have with current "efforts", is that once someone
> reports a bug, the onus seems to be 99% on the *reporter* to find
> the exact line of code or commit.  Ghad what a repressive method.

This is the only method that scales.

Developer has only 24 hours in each day, and sometimes he needs to eat,
sleep, and maybe even pay attention to e.g. his kids.

But bug reporters are much more numerous and they have more
hours in one day combined.

BUT - it means that developers should try to increase user base,
not scare users away.

> And if the "developer" who broke the damn thing, or who at least
> "claims" to be supporting that code, cannot "reproduce" the bug,
> they drop it completely.

Developer should let reporter know that reporter needs to help
a bit here. Sometimes a bit of hand holding is needed, but it
pays off because you breed more qualified testers/bug reporters.

> Contrast that flawed approach with how Linus does things..
> he thinks through the symptoms, matches them to the code,
> and figures out what the few possibilities might be,
> and feeds back some trial balloon patches for the bug reporter to try.
>
> MUCH better.
>
> And remember, *I'm* an old-time Linux kernel developer.. just think about
> the people reporting bugs who haven't been around here since 1992..

Yes. Developers should not grow more and more unhelpful
and arrogant towards their users just because inexperienced
users send incomplete/poorly written bug reports.
They need to provide help, not humiliate/ignore.

I think we agree here.
--
vda

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:56                   ` Adrian Bunk
  2007-11-13 18:57                     ` Gabriel C
@ 2007-11-14  0:39                     ` Denys Vlasenko
  2007-11-14  7:27                       ` Adrian Bunk
  2007-11-14 16:55                     ` Jan Evert van Grootheest
  2 siblings, 1 reply; 268+ messages in thread
From: Denys Vlasenko @ 2007-11-14  0:39 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tuesday 13 November 2007 10:56, Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 12:13:56PM -0500, Theodore Tso wrote:
> > On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
> > > Btw, I used to test every -mm kernel. But since I've switched distros
> > > (gentoo->ubuntu)
> > > and I have less time, I feel it's harder to test -rc or -mm kernels (I
> > > know this isn't a lkml problem
> > > but more a distro problem, but I would love having an ubuntu blessed
> > > repo with current dev kernel
> > > for the latest stable ubuntu release).
> >
> > There are two parts to this.  One is a Ubuntu development kernel which
> > we can give to large numbers of people to expand our testing pool.
> > But if we don't do a better job of responding to bug reports that
> > would be generated by expanded testing this won't necessarily help us.
> >...
>
> The main problem aren't missing testers [1] - we already have relatively
> experienced people testing kernels and/or reporting bugs, and we slowly
> scare them away due to the many bug reports without any reaction.
>
> The main problem is finding experienced developers who spend time on
> looking into bug reports.
>
> Getting many relatively unexperienced users (who need more guidance for
> debugging issues) as additional testers is therefore IMHO not
> necessarily a good idea.

And where experienced developrs are coming from?
They are not born with Linux kernel skills.
They grow up from within user base.

Bigger user base -> more developers (eventually)
--
vda

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:57                     ` Gabriel C
@ 2007-11-14  0:41                       ` Denys Vlasenko
  0 siblings, 0 replies; 268+ messages in thread
From: Denys Vlasenko @ 2007-11-14  0:41 UTC (permalink / raw)
  To: Gabriel C
  Cc: Adrian Bunk, Theodore Tso, Benoit Boissinot, Mark Lord,
	Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tuesday 13 November 2007 11:57, Gabriel C wrote:
> > The main problem is finding experienced developers who spend time on
> > looking into bug reports.
>
> There are already. IMO the problem is the development model.
>
> There are tons new features in each new kernel release and 'tons new bugs'
> which are not fixed during the release cycle nor in the .XX stable kernels.
>
> Maybe after XX kernel releases there should be one just with bug-fixes
> _without_ any new features , eg: cleaning bugs from bugzilla , know
> regressions , cleaning up code , removing broken drivers and the like.

Won't work. You cannot force people to work on things they don't
find interesting, long-term.
--
vda

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:12                                 ` Alan Cox
@ 2007-11-14  0:52                                   ` Chuck Ebbert
  2007-11-14  1:11                                     ` Stephen Hemminger
  0 siblings, 1 reply; 268+ messages in thread
From: Chuck Ebbert @ 2007-11-14  0:52 UTC (permalink / raw)
  To: Alan Cox
  Cc: Adrian Bunk, Mark Lord, Ingo Molnar, Andrew Morton, David Miller,
	protasnb, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On 11/13/2007 04:12 PM, Alan Cox wrote:
>> Bug fixing is not about finding someone to blame, it's about getting the 
>> bug fixed.
> 
> Partly - its also about understanding why the bug occurred and making it
> not happen again.

Very few people think about that part.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:18                     ` Mark Lord
  2007-11-13 18:36                       ` Adrian Bunk
@ 2007-11-14  1:10                       ` David Miller
  2007-11-14  1:18                         ` Peter Stuge
  1 sibling, 1 reply; 268+ messages in thread
From: David Miller @ 2007-11-14  1:10 UTC (permalink / raw)
  To: liml
  Cc: bunk, mingo, akpm, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

From: Mark Lord <liml@rtr.ca>
Date: Tue, 13 Nov 2007 13:18:43 -0500

> Mind you, no arguing that this is effective when that poor bloke has
> a day free to download the git-tree and build/reboot a dozen times.

Like the internet, this time spent is beneficial because it's
pushing the work out to the end nodes.  In fact git bisect is
an awesome example of the end node principle in action for
software development and QA.

For the end-user wanting their bug fixed and the developer it's a win
win situation because the reporter is actually able to do something
proactive which will help get the bug they want fixed faster.

So I don't agree with framing this person as a "poor bloke".  Our
testers are more empowered than ever to lead the process towards a
fix.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  0:52                                   ` Chuck Ebbert
@ 2007-11-14  1:11                                     ` Stephen Hemminger
  2007-11-14  2:10                                       ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Stephen Hemminger @ 2007-11-14  1:11 UTC (permalink / raw)
  To: Chuck Ebbert
  Cc: Alan Cox, Adrian Bunk, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 19:52:17 -0500
Chuck Ebbert <cebbert@redhat.com> wrote:

> On 11/13/2007 04:12 PM, Alan Cox wrote:
> >> Bug fixing is not about finding someone to blame, it's about getting the 
> >> bug fixed.
> > 
> > Partly - its also about understanding why the bug occurred and making it
> > not happen again.
> 
> Very few people think about that part.

Why does the kernel have very few useful tests?
 Lack of interest? resources? expertise?
Ideally each new feature would just be a small add on to an existing test.

Unlike developing new features which seems to grow well with more developers.
Bug fixing also seems to be a scarcity process. There often seems to be
a very few people that understand the problem well enough or have the necessary
hardware to reproduce and fix the problem.

Recent changes like tickless and scheduler rework were well thought out and caused
very little impact to 90% of the users. The problem is the 10% who do have problems.
Worse, the developers often only hear about the a small sample of those.

-- 
Stephen Hemminger <shemminger@linux-foundation.org>

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  1:10                       ` David Miller
@ 2007-11-14  1:18                         ` Peter Stuge
  0 siblings, 0 replies; 268+ messages in thread
From: Peter Stuge @ 2007-11-14  1:18 UTC (permalink / raw)
  To: linux-pcmcia, linux-kernel

Please stop cross-posting this thread at least to linux-pcmcia
until your post is relevant to PCMCIA.

Sorry for being a bore. (Not that I don't love reading LKML
discussions, but I found that it took too much time, and now
they're over at linux-pcmcia too! :)

Thank you in advance.


//Peter

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:32                   ` Andrew Morton
  2007-11-13 23:09                     ` Russell King
@ 2007-11-14  1:55                     ` David Miller
  2007-11-14  2:27                       ` Andrew Morton
  2007-11-14  9:55                       ` Russell King
  1 sibling, 2 replies; 268+ messages in thread
From: David Miller @ 2007-11-14  1:55 UTC (permalink / raw)
  To: akpm
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 13 Nov 2007 14:32:01 -0800

> On Tue, 13 Nov 2007 22:18:01 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> 
> > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > try to change my mind.
> 
> Making a list subscribers-only will cause some bug reports to be lost.
> 
> Tradeoffs are involved, against which decisions must be made.  You have
> made yours.

Russell doesn't have to worry any more, he doesn't have to
host it, and he doesn't have to be willing to run a
non-subscribers-only mailing list.

Because I am.

I've created linux-arm@vger.kernel.org

Enjoy.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 23:40                   ` Russell King
@ 2007-11-14  1:56                     ` David Miller
  0 siblings, 0 replies; 268+ messages in thread
From: David Miller @ 2007-11-14  1:56 UTC (permalink / raw)
  To: rmk+lkml
  Cc: liml, mingo, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm

From: Russell King <rmk+lkml@arm.linux.org.uk>
Date: Tue, 13 Nov 2007 23:40:33 +0000

> ARM ep93xx defconfig has been broken since 2.6.23-git1 due to:
> 
> drivers/net/arm/ep93xx_eth.c:420: error: implicit declaration of function '__netif_rx_schedule_prep'
> 
> caused by: [NET]: Make NAPI polling independent of struct net_device objects.
> 
> ARM netx defconfig has been broken since 2.6.23-git1 due to:
> 
> drivers/net/netx-eth.c: In function 'netx_eth_hard_start_xmit':
> drivers/net/netx-eth.c:131: error: 'dev' undeclared (first use in this function)
> drivers/net/netx-eth.c:131: error: (Each undeclared identifier is reported only once
> drivers/net/netx-eth.c:131: error: for each function it appears in.)
> drivers/net/netx-eth.c: In function 'netx_eth_receive':
> drivers/net/netx-eth.c:158: error: 'dev' undeclared (first use in this function)
> 
> caused by: [NET] drivers/net: statistics cleanup #1 -- save memory and shrink code
> 

I'll fix these up, thanks for the report.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  1:11                                     ` Stephen Hemminger
@ 2007-11-14  2:10                                       ` Andrew Morton
  0 siblings, 0 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-14  2:10 UTC (permalink / raw)
  To: Stephen Hemminger
  Cc: Chuck Ebbert, Alan Cox, Adrian Bunk, Mark Lord, Ingo Molnar,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007 17:11:36 -0800 Stephen Hemminger <shemminger@linux-foundation.org> wrote:

> On Tue, 13 Nov 2007 19:52:17 -0500
> Chuck Ebbert <cebbert@redhat.com> wrote:
> 
> > On 11/13/2007 04:12 PM, Alan Cox wrote:
> > >> Bug fixing is not about finding someone to blame, it's about getting the 
> > >> bug fixed.
> > > 
> > > Partly - its also about understanding why the bug occurred and making it
> > > not happen again.
> > 
> > Very few people think about that part.
> 
> Why does the kernel have very few useful tests?

Tests would of course be nice, but they aren't very useful(!)

Looking at this list which Natalie has generated I see around thirty which
are dependent on the right hardware and ten which are not.  This ratio is
typical, I think.  In fact I'd say that more than 75% of reported bugs are
dependent on hardware.

So the best test of all for the kernel is "run it on a different machine". 
This is why we are sooooo dependent upon our volunteer testers/reporters to
be able to do kernel development.

>  Lack of interest? resources? expertise?
> Ideally each new feature would just be a small add on to an existing test.

Sure.  For system-call-visible features it would be good to do that.

But this tends not to be where bugs get exposed.  Because the original
developer can 100% exercise such code.  That isn't the case with
driver/arch/platform changes.

> Unlike developing new features which seems to grow well with more developers.
> Bug fixing also seems to be a scarcity process. There often seems to be
> a very few people that understand the problem well enough or have the necessary
> hardware to reproduce and fix the problem.

We're 100% dead if "having the hardware" is a prerequisite to fixing a bug.
The terminal state there is that the kernel runs on about 200 machines
worldwide.  We have to work with reporters via email to fix these sorts of
things.  As we of course do.

> Recent changes like tickless and scheduler rework were well thought out and caused
> very little impact to 90% of the users. The problem is the 10% who do have problems.
> Worse, the developers often only hear about the a small sample of those.

Yes.  An unknown number of people just shrug and go back to an old kernel.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  1:55                     ` David Miller
@ 2007-11-14  2:27                       ` Andrew Morton
  2007-11-14  3:47                         ` David Miller
  2007-11-14  8:30                         ` Russell King
  2007-11-14  9:55                       ` Russell King
  1 sibling, 2 replies; 268+ messages in thread
From: Andrew Morton @ 2007-11-14  2:27 UTC (permalink / raw)
  To: David Miller
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, 13 Nov 2007 17:55:51 -0800 (PST) David Miller <davem@davemloft.net> wrote:

> I've created linux-arm@vger.kernel.org

Let me just say - I'm astonished at how little spam gets though the vger
lists.  Considering how many times those email addresses must have been
added to spam databases.

It must be a lot of work, and whoever is doing it does it well.

I don't even know.  Is it Matti?  You?

<contemplates linux-kernel@lists.sourceforge.net.  Shudders.>

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  2:27                       ` Andrew Morton
@ 2007-11-14  3:47                         ` David Miller
  2007-11-14  8:30                         ` Russell King
  1 sibling, 0 replies; 268+ messages in thread
From: David Miller @ 2007-11-14  3:47 UTC (permalink / raw)
  To: akpm
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 13 Nov 2007 18:27:00 -0800

> Let me just say - I'm astonished at how little spam gets though the vger
> lists.  Considering how many times those email addresses must have been
> added to spam databases.
> 
> It must be a lot of work, and whoever is doing it does it well.
> 
> I don't even know.  Is it Matti?  You?

Matti gets all the credit for setting up the bayesian et al.
filters we have and training it as needed.

> <contemplates linux-kernel@lists.sourceforge.net.  Shudders.>

Yes, sourceforge is a complete joke.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:46     ` Martin Bligh
  2007-11-13 18:47       ` Andrew Morton
@ 2007-11-14  5:07       ` David Miller
  1 sibling, 0 replies; 268+ messages in thread
From: David Miller @ 2007-11-14  5:07 UTC (permalink / raw)
  To: mbligh; +Cc: James.Bottomley, akpm, protasnb, linux-kernel, linux-scsi

From: "Martin Bligh" <mbligh@google.com>
Date: Tue, 13 Nov 2007 09:46:08 -0800

> This is a technical issue with vger.kernel.org mailing lists that I've tried
> addressing before - maybe davem can help fix it?

I think the problem is that certain mail headers show up multiple
times and this makes it look like a looping email so we toss it.

I suspect the one you really need to block out is X-MailingList
or similar.

Why don't you do a few tries and I'll try to remember to keep an
eye out for the bounces?

Thanks.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:18                 ` Russell King
  2007-11-13 22:32                   ` Andrew Morton
@ 2007-11-14  5:56                   ` Sam Ravnborg
  2007-11-14  5:59                     ` Sam Ravnborg
  2007-11-14  6:13                     ` David Miller
  1 sibling, 2 replies; 268+ messages in thread
From: Sam Ravnborg @ 2007-11-14  5:56 UTC (permalink / raw)
  To: Andrew Morton, David Miller, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input

> 
> > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > some bug reporters to give up and go away.
> 
> Find some other mailing list; I'm not hosting *nor* am I willing to run a
> non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> try to change my mind.

The postmasters at vger is pretty good at running mailing lists.
For linux-kbuild my effort so far has been to request it.
Thats not a big deal.

So if they accept it you could have linux-arm@vger.kernel.org for zero
overhead for you.

	Sam

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  5:56                   ` [BUG] New Kernel Bugs Sam Ravnborg
@ 2007-11-14  5:59                     ` Sam Ravnborg
  2007-11-14  6:13                     ` David Miller
  1 sibling, 0 replies; 268+ messages in thread
From: Sam Ravnborg @ 2007-11-14  5:59 UTC (permalink / raw)
  To: Andrew Morton, David Miller, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input

On Wed, Nov 14, 2007 at 06:56:06AM +0100, Sam Ravnborg wrote:
> > 
> > > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > > some bug reporters to give up and go away.
> > 
> > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > try to change my mind.
> 
> The postmasters at vger is pretty good at running mailing lists.
> For linux-kbuild my effort so far has been to request it.
> Thats not a big deal.
> 
> So if they accept it you could have linux-arm@vger.kernel.org for zero
> overhead for you.

And in a later mail I saw davem already created it.

	Sam

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  5:56                   ` [BUG] New Kernel Bugs Sam Ravnborg
  2007-11-14  5:59                     ` Sam Ravnborg
@ 2007-11-14  6:13                     ` David Miller
  1 sibling, 0 replies; 268+ messages in thread
From: David Miller @ 2007-11-14  6:13 UTC (permalink / raw)
  To: sam
  Cc: akpm, alsa-devel, netdev, linux-pcmcia, linux-kernel, protasnb,
	linux-ide, bugme-daemon, linux-input

From: Sam Ravnborg <sam@ravnborg.org>
Date: Wed, 14 Nov 2007 06:56:06 +0100

> > 
> > > If so, MANITAINERS claims that it is subscribers-only.  That would cause
> > > some bug reporters to give up and go away.
> > 
> > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > try to change my mind.
> 
> The postmasters at vger is pretty good at running mailing lists.
> For linux-kbuild my effort so far has been to request it.
> Thats not a big deal.
> 
> So if they accept it you could have linux-arm@vger.kernel.org for zero
> overhead for you.

I already did, get a little deeper in your mailbox before
replying :-)

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  0:39                     ` Denys Vlasenko
@ 2007-11-14  7:27                       ` Adrian Bunk
  2007-11-14  7:46                         ` Denys Vlasenko
  0 siblings, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-14  7:27 UTC (permalink / raw)
  To: Denys Vlasenko
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, Nov 13, 2007 at 05:39:45PM -0700, Denys Vlasenko wrote:
> On Tuesday 13 November 2007 10:56, Adrian Bunk wrote:
> > On Tue, Nov 13, 2007 at 12:13:56PM -0500, Theodore Tso wrote:
> > > On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
> > > > Btw, I used to test every -mm kernel. But since I've switched distros
> > > > (gentoo->ubuntu)
> > > > and I have less time, I feel it's harder to test -rc or -mm kernels (I
> > > > know this isn't a lkml problem
> > > > but more a distro problem, but I would love having an ubuntu blessed
> > > > repo with current dev kernel
> > > > for the latest stable ubuntu release).
> > >
> > > There are two parts to this.  One is a Ubuntu development kernel which
> > > we can give to large numbers of people to expand our testing pool.
> > > But if we don't do a better job of responding to bug reports that
> > > would be generated by expanded testing this won't necessarily help us.
> > >...
> >
> > The main problem aren't missing testers [1] - we already have relatively
> > experienced people testing kernels and/or reporting bugs, and we slowly
> > scare them away due to the many bug reports without any reaction.
> >
> > The main problem is finding experienced developers who spend time on
> > looking into bug reports.
> >
> > Getting many relatively unexperienced users (who need more guidance for
> > debugging issues) as additional testers is therefore IMHO not
> > necessarily a good idea.
> 
> And where experienced developrs are coming from?
> They are not born with Linux kernel skills.
> They grow up from within user base.
> 
> Bigger user base -> more developers (eventually)

You missed the following in my email:
"we slowly scare them away due to the many bug reports without any 
 reaction."

The problem is that bug reports take time. If you go away from easy 
things like compile errors then even things like describing what does
no longer work, ideally producing a scenario where you can reproduce it 
and verifying whether it was present in previous kernels can easily take 
many hours that are spent before the initial bug report.

If the bug report then gets ignored we discourage the person who sent 
the bug report to do any work related to the kernel again.

> vda

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  7:27                       ` Adrian Bunk
@ 2007-11-14  7:46                         ` Denys Vlasenko
  2007-11-14 13:30                           ` Matthew Wilcox
  2007-11-14 18:27                           ` Kok, Auke
  0 siblings, 2 replies; 268+ messages in thread
From: Denys Vlasenko @ 2007-11-14  7:46 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wednesday 14 November 2007 00:27, Adrian Bunk wrote:
> You missed the following in my email:
> "we slowly scare them away due to the many bug reports without any
>  reaction."
>
> The problem is that bug reports take time. If you go away from easy
> things like compile errors then even things like describing what does
> no longer work, ideally producing a scenario where you can reproduce it
> and verifying whether it was present in previous kernels can easily take
> many hours that are spent before the initial bug report.
>
> If the bug report then gets ignored we discourage the person who sent
> the bug report to do any work related to the kernel again.

Cannot agree more. I am in a similar position right now.
My patch to aic7xxx driver was ubmitted four times
with not much reaction from scsi guys.

Finally they replied and asked to rediff it against their
git tree. I did that and sent patches back. No reply since then.

And mind you, the patch is not trying to do anything
complex, it mostly moves code around, removes 'inline',
adds 'const'. What should I think about it?
--
vda

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Moderated list (Was: Re: [BUG] New Kernel Bugs)
  2007-11-14 12:01                               ` David Miller
@ 2007-11-14  8:25                                 ` Takashi Iwai
  2007-11-14 12:21                                   ` Rene Herman
  2007-11-14 12:12                                 ` [alsa-devel] [BUG] New Kernel Bugs Rene Herman
  1 sibling, 1 reply; 268+ messages in thread
From: Takashi Iwai @ 2007-11-14  8:25 UTC (permalink / raw)
  To: David Miller
  Cc: rene.herman, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, perex

At Wed, 14 Nov 2007 04:01:31 -0800 (PST),
David Miller wrote:
> 
> From: David Miller <davem@davemloft.net>
> Date: Wed, 14 Nov 2007 03:56:57 -0800 (PST)
> 
> > The fact that it farts at me every time I post to this thread.
> 
> See?  I got another one and I have received at least 10 of the
> following over the past 2 days.
> 
> That's rediculious.
> 
> And because a human adds the whitelist this is always going to
> happen to someone when they start posting to the alsa list for
> the first time.

... if you give too many recipients in your post.  That is often
really annoying thing to me, together with keeping the unrelated
subject line ;)

I personally don't care whether it's a moderated or open list.
We chose it simply due to too bad S/N ratio at that time.  So, if the
current list annoys your or many others and the list management on
vger is so good, it'd be basically a good move, of course.  I'll
appreciate it.

The only confusion would be the change of ML address, but we can do it
slowly, too.


Takashi

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  2:27                       ` Andrew Morton
  2007-11-14  3:47                         ` David Miller
@ 2007-11-14  8:30                         ` Russell King
  1 sibling, 0 replies; 268+ messages in thread
From: Russell King @ 2007-11-14  8:30 UTC (permalink / raw)
  To: Andrew Morton
  Cc: David Miller, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 06:27:00PM -0800, Andrew Morton wrote:
> On Tue, 13 Nov 2007 17:55:51 -0800 (PST) David Miller <davem@davemloft.net> wrote:
> 
> > I've created linux-arm@vger.kernel.org
> 
> Let me just say - I'm astonished at how little spam gets though the vger
> lists.  Considering how many times those email addresses must have been
> added to spam databases.
> 
> It must be a lot of work, and whoever is doing it does it well.
> 
> I don't even know.  Is it Matti?  You?
> 
> <contemplates linux-kernel@lists.sourceforge.net.  Shudders.>

Martin's changed the owner for ARM bugs last night to the mailing list
so the whole issue is now redundant.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Moderated list (Was: Re: [BUG] New Kernel Bugs)
  2007-11-14 12:21                                   ` Rene Herman
@ 2007-11-14  9:47                                     ` Takashi Iwai
  2007-11-14 23:23                                       ` Moderated list David Miller
  0 siblings, 1 reply; 268+ messages in thread
From: Takashi Iwai @ 2007-11-14  9:47 UTC (permalink / raw)
  To: Rene Herman
  Cc: David Miller, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, perex

At Wed, 14 Nov 2007 13:21:30 +0100,
Rene Herman wrote:
> 
> On 14-11-07 09:25, Takashi Iwai wrote:
> 
> > At Wed, 14 Nov 2007 04:01:31 -0800 (PST),
> > David Miller wrote:
> >> From: David Miller <davem@davemloft.net>
> >> Date: Wed, 14 Nov 2007 03:56:57 -0800 (PST)
> >>
> >>> The fact that it farts at me every time I post to this thread.
> >> See?  I got another one and I have received at least 10 of the
> >> following over the past 2 days.
> >>
> >> That's rediculious.
> >>
> >> And because a human adds the whitelist this is always going to
> >> happen to someone when they start posting to the alsa list for
> >> the first time.
> > 
> > ... if you give too many recipients in your post.  That is often
> > really annoying thing to me, together with keeping the unrelated
> > subject line ;)
> > 
> > I personally don't care whether it's a moderated or open list.
> > We chose it simply due to too bad S/N ratio at that time.  So, if the
> > current list annoys your or many others and the list management on
> > vger is so good, it'd be basically a good move, of course.  I'll
> > appreciate it.
> > 
> > The only confusion would be the change of ML address, but we can do it
> > slowly, too.
> 
> I'd love the lists at vger. Amazing spam-filtering. I'd like to request the 
> name alsa-devel@vger.kernel.org (and alsa-user@vger.kernel.org if at all 
> possible so we can open that one up as well) though.

I think alsa-user can stay as is.  It's no place for dragging many
other addresses like alsa-devel.

BTW, I also prefer keeping the name alsa-devel@.  It's been so.

> There wouldn't need to be a forced ML address change if Jaroslov would then 
> just rewrite alsa-{devel,user}@alsa-project.org to vger.kernel.org same as 
> he did for alsa-devel and does for alsa-user to @lists.sf.net.

If it works, then I'm for it, too.


thanks,

Takashi

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  1:55                     ` David Miller
  2007-11-14  2:27                       ` Andrew Morton
@ 2007-11-14  9:55                       ` Russell King
  2007-11-14 10:07                         ` David Miller
  1 sibling, 1 reply; 268+ messages in thread
From: Russell King @ 2007-11-14  9:55 UTC (permalink / raw)
  To: David Miller
  Cc: akpm, netdev, linux-pcmcia, alsa-devel, protasnb, linux-kernel,
	linux-ide, bugme-daemon, linux-input

On Tue, Nov 13, 2007 at 05:55:51PM -0800, David Miller wrote:
> From: Andrew Morton <akpm@linux-foundation.org>
> Date: Tue, 13 Nov 2007 14:32:01 -0800
> 
> > On Tue, 13 Nov 2007 22:18:01 +0000 Russell King <rmk+lkml@arm.linux.org.uk> wrote:
> > 
> > > Find some other mailing list; I'm not hosting *nor* am I willing to run a
> > > non-subscribers only mailing list.  Period.  Not negotiable, so don't even
> > > try to change my mind.
> > 
> > Making a list subscribers-only will cause some bug reports to be lost.
> > 
> > Tradeoffs are involved, against which decisions must be made.  You have
> > made yours.
> 
> Russell doesn't have to worry any more, he doesn't have to
> host it, and he doesn't have to be willing to run a
> non-subscribers-only mailing list.
> 
> Because I am.
> 
> I've created linux-arm@vger.kernel.org

By doing so you've just said (implicitly) that you can not tolerate
someone having a different opinion from your own.

While I accept *your* right to run *your* lists how you please, you
are unable to accept *my* right to run *my* lists how I see fit.

Time will tell which lists will survive.  Whatever, I suspect that by
doing what you've just done, you're going to create more confusion and
problems. Instead of having one focused place for discussions and bug
reports, they're going to be spread more thinly, meaning less people
looking at such things, meaning more bugs get ignored.  Thus making
the issue worse.

So, when are you creating a replacement alsa-devel mailing list on
vger?  That's also subscribers-only.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  9:55                       ` Russell King
@ 2007-11-14 10:07                         ` David Miller
  2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
                                             ` (2 more replies)
  0 siblings, 3 replies; 268+ messages in thread
From: David Miller @ 2007-11-14 10:07 UTC (permalink / raw)
  To: rmk+lkml
  Cc: akpm, netdev, linux-pcmcia, alsa-devel, protasnb, linux-kernel,
	linux-ide, bugme-daemon, linux-input

From: Russell King <rmk+lkml@arm.linux.org.uk>
Date: Wed, 14 Nov 2007 09:55:07 +0000

> On Tue, Nov 13, 2007 at 05:55:51PM -0800, David Miller wrote:
> > I've created linux-arm@vger.kernel.org
> 
> By doing so you've just said (implicitly) that you can not tolerate
> someone having a different opinion from your own.

I created a mailing list on a machine where I provide such services.

People can choose to use or not use the new list, it is their choice.

> While I accept *your* right to run *your* lists how you please, you
> are unable to accept *my* right to run *my* lists how I see fit.

I didn't tell you to take your list down or to run it in some other
way.  I didn't tell you to unsubscribe everyone and move them over
to the new list either.

I've provided an alternative, and people can pick and choose how they
see fit.  I'm letting natural selection run it's course.  Are you
able to cope with the fact that people might not want to use your
list any longer?  Perhaps that is what bugs you so much about my
giving people a alternative choice.

> So, when are you creating a replacement alsa-devel mailing list on
> vger?  That's also subscribers-only.

The operative term is "alternative" rather than "replacement".
Perhaps this misunderstanding is what you're so upset about.

And yes, that alsa list bugs the crap out of me too.  I'm more than
happy to provide an alternative for that one as well.

In fact, *poof*, there it is, linux-alsa@vger.kernel.org is there and
available for anyone who wants to use it.

Have a nice day Russell.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 10:07                         ` David Miller
@ 2007-11-14 11:46                           ` Rene Herman
  2007-11-14 11:56                             ` David Miller
  2007-11-15  4:16                             ` Bron Gondwana
  2007-11-14 19:44                           ` Russell King
  2007-11-16 22:16                           ` Use *poof* for linux-omap (Was: [BUG] New Kernel Bugs) Tony Lindgren
  2 siblings, 2 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-14 11:46 UTC (permalink / raw)
  To: David Miller
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm,
	Jaroslav Kysela, Takashi Iwai

On 14-11-07 11:07, David Miller wrote:

Added Jaroslav and Takashi to the already extensive CC....

> From: Russell King <rmk+lkml@arm.linux.org.uk>

>> So, when are you creating a replacement alsa-devel mailing list on
>> vger?  That's also subscribers-only.
> 
> The operative term is "alternative" rather than "replacement".
> Perhaps this misunderstanding is what you're so upset about.
> 
> And yes, that alsa list bugs the crap out of me too.  I'm more than
> happy to provide an alternative for that one as well.

alsa-devel@alsa-project.org is not subscriber-only. Same as that arm list, 
it's _moderated_ for non-subscribers and given that I and other moderators 
have been doing our best to moderate quickly (I tend to stay logged in to 
the moderation interface all day for example) what specifically bugged the 
crap out of you? It's not something a poster needs to concern himself with.

Also for alsa-devel the moderators tend to add any valid non-subcribers to 
a whitelist after landing in the queue the first time meaning even a delay 
is just a one-time thing normally. So what's the trouble? Basically, noone 
need even notice...

> In fact, *poof*, there it is, linux-alsa@vger.kernel.org is there and
> available for anyone who wants to use it.

Not that I think that moving alsa-devel over to vger wouldn't be a good idea 
mind you; when the list moved from sourceforge, asking you to host it was my 
preferred option. I do somewhat suspect that Jaroslav would like to keep the 
alsa-devel@ name (and I'd like to ask you to then also host alsa-user@) and 
would then rewrite mail to those lists @alsa-project.org to vger.

But what is the problem you speak of with the alsa-devel list? While I would 
not mind loosing it, moderation hasn't been overly laborious and I'm not 
aware of any serious problems.

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
@ 2007-11-14 11:56                             ` David Miller
  2007-11-14 12:01                               ` David Miller
  2007-11-14 12:09                               ` Rene Herman
  2007-11-15  4:16                             ` Bron Gondwana
  1 sibling, 2 replies; 268+ messages in thread
From: David Miller @ 2007-11-14 11:56 UTC (permalink / raw)
  To: rene.herman
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm, perex,
	tiwai

From: Rene Herman <rene.herman@keyaccess.nl>
Date: Wed, 14 Nov 2007 12:46:24 +0100

> alsa-devel@alsa-project.org is not subscriber-only. Same as that arm list, 
> it's _moderated_ for non-subscribers and given that I and other moderators 
> have been doing our best to moderate quickly (I tend to stay logged in to 
> the moderation interface all day for example) what specifically bugged the 
> crap out of you? It's not something a poster needs to concern himself with.

The fact that it farts at me every time I post to this thread.  That's
rude and annoying.

> Also for alsa-devel the moderators tend to add any valid non-subcribers to 
> a whitelist after landing in the queue the first time meaning even a delay 
> is just a one-time thing normally. So what's the trouble? Basically, noone 
> need even notice...

That sucks for new people taking part in the conversation.

There is no reason for moderation at all, it isn't necessary
for spam prevention and it does nothing but annoy new posters
and make work for the moderator.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 11:56                             ` David Miller
@ 2007-11-14 12:01                               ` David Miller
  2007-11-14  8:25                                 ` Moderated list (Was: Re: [BUG] New Kernel Bugs) Takashi Iwai
  2007-11-14 12:12                                 ` [alsa-devel] [BUG] New Kernel Bugs Rene Herman
  2007-11-14 12:09                               ` Rene Herman
  1 sibling, 2 replies; 268+ messages in thread
From: David Miller @ 2007-11-14 12:01 UTC (permalink / raw)
  To: rene.herman
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm, perex,
	tiwai

From: David Miller <davem@davemloft.net>
Date: Wed, 14 Nov 2007 03:56:57 -0800 (PST)

> The fact that it farts at me every time I post to this thread.

See?  I got another one and I have received at least 10 of the
following over the past 2 days.

That's rediculious.

And because a human adds the whitelist this is always going to
happen to someone when they start posting to the alsa list for
the first time.

/me gets ready for the 11th copy in response to this one...

--------------------
Subject: Your message to Alsa-devel awaits moderator approval
From: alsa-devel-bounces@alsa-project.org
To: davem@davemloft.net
Date: Wed, 14 Nov 2007 12:57:06 +0100
Sender: alsa-devel-bounces@alsa-project.org

Your mail to 'Alsa-devel' with the subject

    Re: [alsa-devel] [BUG] New Kernel Bugs

Is being held until the list moderator can review it for approval.

The reason it is being held:

    Too many recipients to the message

Either the message will get posted to the list, or you will receive
notification of the moderator's decision.  If you would like to cancel
this posting, please visit the following URL:

    http://mailman.alsa-project.org/mailman/confirm/alsa-devel/12dd3bd077bbf9cd142f214beae6d22ae43b53aa


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 11:56                             ` David Miller
  2007-11-14 12:01                               ` David Miller
@ 2007-11-14 12:09                               ` Rene Herman
  1 sibling, 0 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-14 12:09 UTC (permalink / raw)
  To: David Miller
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm, perex,
	tiwai

On 14-11-07 12:56, David Miller wrote:

> From: Rene Herman <rene.herman@keyaccess.nl>
> Date: Wed, 14 Nov 2007 12:46:24 +0100
> 
>> alsa-devel@alsa-project.org is not subscriber-only. Same as that arm list, 
>> it's _moderated_ for non-subscribers and given that I and other moderators 
>> have been doing our best to moderate quickly (I tend to stay logged in to 
>> the moderation interface all day for example) what specifically bugged the 
>> crap out of you? It's not something a poster needs to concern himself with.
> 
> The fact that it farts at me every time I post to this thread.  That's
> rude and annoying.

It certainly is. I only experienced that now due to the "too many recipients 
to message" moderation notice that I got from my own message.

Jaroslav -- please disable that junk or if possible, make it a "at most once 
per address per month" thing or somesuch. This is complete crap.

>> Also for alsa-devel the moderators tend to add any valid non-subcribers to 
>> a whitelist after landing in the queue the first time meaning even a delay 
>> is just a one-time thing normally. So what's the trouble? Basically, noone 
>> need even notice...
> 
> That sucks for new people taking part in the conversation.
> 
> There is no reason for moderation at all, it isn't necessary
> for spam prevention and it does nothing but annoy new posters
> and make work for the moderator.

Yes there is. It's necessary for lists that do not have the human and other 
resouces behind it that vger does. alsa-devel was drowning in spam and dying 
as a result back when it was at sourceforge. Upon moving, my preference was 
to ask the lists to be hosted at vger but given that (it seems) Jaroslav 
wanted to keep them locally, moderation was very necessary. I moderate out 
quite a bit of spam every day.

vger is doing an amazing job at spam filtering -- if it's an option to move 
to vger, than sure, no need. But otherwise, the "no need" needs a list admin 
with enough bandwidth and skill.

As to the "new people": it's not optimal, but (upto this thread I'll admit 
-- I woke up to a huge number of posts in the queue) it's not been a _real_ 
problem. alsa-devel is not high-volume enough for it to be.

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 12:01                               ` David Miller
  2007-11-14  8:25                                 ` Moderated list (Was: Re: [BUG] New Kernel Bugs) Takashi Iwai
@ 2007-11-14 12:12                                 ` Rene Herman
  1 sibling, 0 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-14 12:12 UTC (permalink / raw)
  To: David Miller
  Cc: rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm, perex,
	tiwai

On 14-11-07 13:01, David Miller wrote:

> From: David Miller <davem@davemloft.net>
> Date: Wed, 14 Nov 2007 03:56:57 -0800 (PST)
> 
>> The fact that it farts at me every time I post to this thread.
> 
> See?  I got another one and I have received at least 10 of the
> following over the past 2 days.

Nah, in this case you are not even getting them to not being a non-subcriber 
but due to too many CCs. I got one as well. That just needs to be disabled, 
does not have anything to do with non-subscribers (and you're in the white 
list) but is just a retarted bit of list configuration...

(no, I can't personally change it, needs Jaroslav Kysela)

Rene.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Moderated list (Was: Re: [BUG] New Kernel Bugs)
  2007-11-14  8:25                                 ` Moderated list (Was: Re: [BUG] New Kernel Bugs) Takashi Iwai
@ 2007-11-14 12:21                                   ` Rene Herman
  2007-11-14  9:47                                     ` Takashi Iwai
  0 siblings, 1 reply; 268+ messages in thread
From: Rene Herman @ 2007-11-14 12:21 UTC (permalink / raw)
  To: Takashi Iwai
  Cc: David Miller, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, perex

On 14-11-07 09:25, Takashi Iwai wrote:

> At Wed, 14 Nov 2007 04:01:31 -0800 (PST),
> David Miller wrote:
>> From: David Miller <davem@davemloft.net>
>> Date: Wed, 14 Nov 2007 03:56:57 -0800 (PST)
>>
>>> The fact that it farts at me every time I post to this thread.
>> See?  I got another one and I have received at least 10 of the
>> following over the past 2 days.
>>
>> That's rediculious.
>>
>> And because a human adds the whitelist this is always going to
>> happen to someone when they start posting to the alsa list for
>> the first time.
> 
> ... if you give too many recipients in your post.  That is often
> really annoying thing to me, together with keeping the unrelated
> subject line ;)
> 
> I personally don't care whether it's a moderated or open list.
> We chose it simply due to too bad S/N ratio at that time.  So, if the
> current list annoys your or many others and the list management on
> vger is so good, it'd be basically a good move, of course.  I'll
> appreciate it.
> 
> The only confusion would be the change of ML address, but we can do it
> slowly, too.

I'd love the lists at vger. Amazing spam-filtering. I'd like to request the 
name alsa-devel@vger.kernel.org (and alsa-user@vger.kernel.org if at all 
possible so we can open that one up as well) though.

There wouldn't need to be a forced ML address change if Jaroslov would then 
just rewrite alsa-{devel,user}@alsa-project.org to vger.kernel.org same as 
he did for alsa-devel and does for alsa-user to @lists.sf.net.

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (9 preceding siblings ...)
  2007-11-13 18:04   ` Russell King
@ 2007-11-14 12:46   ` Jiri Kosina
  2007-11-14 13:24   ` Pavel Machek
  11 siblings, 0 replies; 268+ messages in thread
From: Jiri Kosina @ 2007-11-14 12:46 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007, Andrew Morton wrote:

> > HID====================================================================
> > 
> > Kernel NULL pointer dereference at :usbhid:hiddev_ioctl+0x2f/0xabc
> > http://bugzilla.kernel.org/show_bug.cgi?id=9216
> > Kernel: 2.6.23.1
> > Looks like this is a regression
> No response from developers

Hi,

it is assigned to 'other_modules@kernel-bugs.osdl.org', so I didn't 
notice, it's as simple as that.

-- 
Jiri Kosina

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 11:15 ` Andrew Morton
                     ` (10 preceding siblings ...)
  2007-11-14 12:46   ` Jiri Kosina
@ 2007-11-14 13:24   ` Pavel Machek
  2007-11-14 14:14     ` Fabio Comolli
  2007-11-14 19:52     ` Russell King
  11 siblings, 2 replies; 268+ messages in thread
From: Pavel Machek @ 2007-11-14 13:24 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Natalie Protasevich, linux-kernel, netdev, alsa-devel, linux-ide,
	linux-pcmcia, linux-input, bugme-daemon

Hi!

> > Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> > http://bugzilla.kernel.org/show_bug.cgi?id=9275
> > Kernel: 2.6.23
> > This is HP notebook nc6320 T2400 945GM
> 
> No response from developers

Maybe I'm optimistic, but I expected Ingo/Thomas to look after nohz
problems. nohz=off highres=off fixes more than one suspend problem...

...stuff I've seen with NOHZ even without suspend (cursor blinking
irregulary) make me think that nohz perhaps should not be used in
production just yet...

							Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  7:46                         ` Denys Vlasenko
@ 2007-11-14 13:30                           ` Matthew Wilcox
  2007-11-14 13:35                             ` Hannes Reinecke
  2007-11-14 18:27                           ` Kok, Auke
  1 sibling, 1 reply; 268+ messages in thread
From: Matthew Wilcox @ 2007-11-14 13:30 UTC (permalink / raw)
  To: Denys Vlasenko
  Cc: Adrian Bunk, alsa-devel, Theodore Tso, Andrew Morton, netdev,
	bugme-daemon, linux-pcmcia, linux-kernel, protasnb, linux-ide,
	Benoit Boissinot, Mark Lord, linux-input, Ingo Molnar,
	David Miller, Hannes Reinecke

On Wed, Nov 14, 2007 at 12:46:20AM -0700, Denys Vlasenko wrote:
> Finally they replied and asked to rediff it against their
> git tree. I did that and sent patches back. No reply since then.
> 
> And mind you, the patch is not trying to do anything
> complex, it mostly moves code around, removes 'inline',
> adds 'const'. What should I think about it?

I'm waiting for an ACK/NAK from Hannes, the maintainer.  What should I
do?

-- 
Intel are signing my paycheques ... these opinions are still mine
"Bill, look, we understand that you're interested in selling us this
operating system, but compare it to ours.  We can't possibly take such
a retrograde step."

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 13:30                           ` Matthew Wilcox
@ 2007-11-14 13:35                             ` Hannes Reinecke
  2007-11-14 21:39                               ` Denys Vlasenko
  0 siblings, 1 reply; 268+ messages in thread
From: Hannes Reinecke @ 2007-11-14 13:35 UTC (permalink / raw)
  To: Matthew Wilcox
  Cc: Denys Vlasenko, Adrian Bunk, alsa-devel, Theodore Tso,
	Andrew Morton, netdev, bugme-daemon, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, Benoit Boissinot, Mark Lord, linux-input,
	Ingo Molnar, David Miller

Matthew Wilcox wrote:
> On Wed, Nov 14, 2007 at 12:46:20AM -0700, Denys Vlasenko wrote:
>> Finally they replied and asked to rediff it against their
>> git tree. I did that and sent patches back. No reply since then.
>>
>> And mind you, the patch is not trying to do anything
>> complex, it mostly moves code around, removes 'inline',
>> adds 'const'. What should I think about it?
> 
> I'm waiting for an ACK/NAK from Hannes, the maintainer.  What should I
> do?
> 
I haven't actually been able to test it here (too busy, sorry). If someone
else confirms it does it's job then

Acked-by: Hannes Reinecke <hare@suse.de>

Cheers,

Hannes
-- 
Dr. Hannes Reinecke		      zSeries & Storage
hare@suse.de			      +49 911 74053 688
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg
GF: Markus Rex, HRB 16746 (AG Nürnberg)

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:55             ` Randy Dunlap
@ 2007-11-14 14:08               ` Ingo Molnar
  2007-11-14 17:38                 ` Randy Dunlap
  2007-11-14 19:56                 ` David Miller
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 14:08 UTC (permalink / raw)
  To: Randy Dunlap
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


* Randy Dunlap <rdunlap@xenotime.net> wrote:

> > (and this is in no way directed at the networking folks - it holds 
> > for all of us. I have one main complaint about networking: the 
> > separate netdev list is a bad idea - networking regressions should 
> > be discussed and fixed on lkml, like most other subsystems are. Any 
> > artificial split of the lk discussion space is bad.)
> 
> but here I disagree.  LKML is already too busy and noisy. Major 
> subsystems need their own discussion areas.

That's a stupid argument. We lose much more by forced isolation of 
discussion than what we win by having less traffic! It's _MUCH_ easier 
to narrow down information (by filter by threads, by topics, by people, 
etc.) than it is to gobble information together from various fractured 
sources. We learned it _again and again_ that isolation of kernel 
discussions causes bad things.

In fact this thread is the very example: David points out that on netdev 
some of those bugs were already discussed and resolved. Had it been all 
on lkml we'd all be aware of it.

this is a single kernel project that is released together as one 
codebase, so a central place of discussion is obvious and common-sense.

so please stop this "too busy and too noisy" nonsense already. It was 
nonsense 10 years ago and it's nonsense today. In 10 years the kernel 
grew from a 1 million lines codebase to an 8 million lines codebase, so 
what? Deal with it and be intelligent about filtering your information 
influx instead of imposing a hard pre-filtering criteria that restricts 
intelligent processing of information.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 13:24   ` Pavel Machek
@ 2007-11-14 14:14     ` Fabio Comolli
  2007-11-14 19:52     ` Russell King
  1 sibling, 0 replies; 268+ messages in thread
From: Fabio Comolli @ 2007-11-14 14:14 UTC (permalink / raw)
  To: Pavel Machek
  Cc: Andrew Morton, Natalie Protasevich, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

FWIW, I see the same problem with another HP notebook, DV4378EA with
radeon X700 video card. It does not happen frequently but I can say
that since I disabled the tickless feature I can't reproduce the
problem anymore.

On Nov 14, 2007 2:24 PM, Pavel Machek <pavel@ucw.cz> wrote:
> Hi!
>
> > > Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9275
> > > Kernel: 2.6.23
> > > This is HP notebook nc6320 T2400 945GM
> >
> > No response from developers
>
> Maybe I'm optimistic, but I expected Ingo/Thomas to look after nohz
> problems. nohz=off highres=off fixes more than one suspend problem...
>
> ...stuff I've seen with NOHZ even without suspend (cursor blinking
> irregulary) make me think that nohz perhaps should not be used in
> production just yet...
>
>                                                         Pavel
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 18:54                         ` Mark Lord
  2007-11-13 22:09                           ` Rafael J. Wysocki
@ 2007-11-14 14:30                           ` Ingo Molnar
  2007-11-14 14:49                             ` Larry Finger
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 14:30 UTC (permalink / raw)
  To: Mark Lord
  Cc: Matthew Wilcox, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, Andrew Morton,
	David Miller


* Mark Lord <liml@rtr.ca> wrote:

>> You're assuming that everything in linux-2.6 was downloaded; that's 
>> not true.  Everything in linux-2.6/.git was downloaded; but then you 
>> do a checkout which happens to approximately double the size of the 
>> linux-2.6 directory.
> ..
>
> Ah, I wondered why it took only half an hour to download.

and you can get even lower than the 260MB by downloading a shallow clone 
of v2.6.23 and then populating the git tree from tht point on. (see the 
--depth parameter of git-clone) [because most of the time you want to 
bisect back to the last stable release, not back to 2 years of git 
history.]

	Ingo


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 14:30                           ` Ingo Molnar
@ 2007-11-14 14:49                             ` Larry Finger
  0 siblings, 0 replies; 268+ messages in thread
From: Larry Finger @ 2007-11-14 14:49 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, alsa-devel, Matthew Wilcox, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	Andrew Morton, David Miller

Ingo Molnar wrote:
> * Mark Lord <liml@rtr.ca> wrote:
> 
>>> You're assuming that everything in linux-2.6 was downloaded; that's 
>>> not true.  Everything in linux-2.6/.git was downloaded; but then you 
>>> do a checkout which happens to approximately double the size of the 
>>> linux-2.6 directory.
>> ..
>>
>> Ah, I wondered why it took only half an hour to download.
> 
> and you can get even lower than the 260MB by downloading a shallow clone 
> of v2.6.23 and then populating the git tree from tht point on. (see the 
> --depth parameter of git-clone) [because most of the time you want to 
> bisect back to the last stable release, not back to 2 years of git 
> history.]

When creating additional git trees (Linville's wireless-2.6 tree, for example) for driver
development, you can save a lot of download bandwidth by using the --reference parameter of git-clone.

Larry

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:56                   ` Adrian Bunk
  2007-11-13 18:57                     ` Gabriel C
  2007-11-14  0:39                     ` Denys Vlasenko
@ 2007-11-14 16:55                     ` Jan Evert van Grootheest
  2 siblings, 0 replies; 268+ messages in thread
From: Jan Evert van Grootheest @ 2007-11-14 16:55 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel, ne

Adrian Bunk wrote:
> On Tue, Nov 13, 2007 at 12:13:56PM -0500, Theodore Tso wrote:
>   
>> On Tue, Nov 13, 2007 at 04:52:32PM +0100, Benoit Boissinot wrote:
>>     
>>> Btw, I used to test every -mm kernel. But since I've switched distros
>>> (gentoo->ubuntu)
>>> and I have less time, I feel it's harder to test -rc or -mm kernels (I
>>> know this isn't a lkml problem
>>> but more a distro problem, but I would love having an ubuntu blessed
>>> repo with current dev kernel
>>> for the latest stable ubuntu release).
>>>       
>> There are two parts to this.  One is a Ubuntu development kernel which
>> we can give to large numbers of people to expand our testing pool.
>> But if we don't do a better job of responding to bug reports that
>> would be generated by expanded testing this won't necessarily help us.
>> ...
>>     
>
> The main problem aren't missing testers [1] - we already have relatively 
> experienced people testing kernels and/or reporting bugs, and we slowly 
> scare them away due to the many bug reports without any reaction.
>
> The main problem is finding experienced developers who spend time on 
> looking into bug reports.
>
> Getting many relatively unexperienced users (who need more guidance for 
> debugging issues) as additional testers is therefore IMHO not 
> necessarily a good idea.
>
> [1] and e.g. when Greg says he has a few hundred people who want to
>     write drivers it would most likely be possible to find a few
>     dozen additional -rc testers among them
>   
Hum. If only each of those would squash one bug a week besides their own 
work...
I would expect he's got a handful that know IDE, another group that is 
into network drivers and so on.

I predict that pile of bugs to disappear in weeks (-;

Just my $0.02.

Jan Evert

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 14:08               ` Ingo Molnar
@ 2007-11-14 17:38                 ` Randy Dunlap
  2007-11-14 18:23                   ` J. Bruce Fields
  2007-11-14 20:16                   ` Ingo Molnar
  2007-11-14 19:56                 ` David Miller
  1 sibling, 2 replies; 268+ messages in thread
From: Randy Dunlap @ 2007-11-14 17:38 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, 14 Nov 2007 15:08:47 +0100 Ingo Molnar wrote:

> 
> * Randy Dunlap <rdunlap@xenotime.net> wrote:
> 
> > > (and this is in no way directed at the networking folks - it holds 
> > > for all of us. I have one main complaint about networking: the 
> > > separate netdev list is a bad idea - networking regressions should 
> > > be discussed and fixed on lkml, like most other subsystems are. Any 
> > > artificial split of the lk discussion space is bad.)
> > 
> > but here I disagree.  LKML is already too busy and noisy. Major 
> > subsystems need their own discussion areas.
> 
> That's a stupid argument. We lose much more by forced isolation of 
> discussion than what we win by having less traffic! It's _MUCH_ easier 
> to narrow down information (by filter by threads, by topics, by people, 
> etc.) than it is to gobble information together from various fractured 
> sources. We learned it _again and again_ that isolation of kernel 
> discussions causes bad things.
> 
> In fact this thread is the very example: David points out that on netdev 
> some of those bugs were already discussed and resolved. Had it been all 
> on lkml we'd all be aware of it.

or had <someone> been on netdev.

> this is a single kernel project that is released together as one 
> codebase, so a central place of discussion is obvious and common-sense.

Central doesn't have to mean one-and-only-one-list-for-everything.

> so please stop this "too busy and too noisy" nonsense already. It was 
> nonsense 10 years ago and it's nonsense today. In 10 years the kernel 
> grew from a 1 million lines codebase to an 8 million lines codebase, so 
> what? Deal with it and be intelligent about filtering your information 
> influx instead of imposing a hard pre-filtering criteria that restricts 
> intelligent processing of information.

So you have a preferred method of handling email.  Please don't
force it on the rest of us.

I'll plan to use lkml-list-only when you have convinced DaveM to drop
all of the other mailing lists at vger.kernel.org.  Yeah, sure.

---
~Randy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 17:38                 ` Randy Dunlap
@ 2007-11-14 18:23                   ` J. Bruce Fields
  2007-11-15  2:50                     ` Neil Brown
  2007-11-14 20:16                   ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: J. Bruce Fields @ 2007-11-14 18:23 UTC (permalink / raw)
  To: Randy Dunlap
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Wed, Nov 14, 2007 at 09:38:20AM -0800, Randy Dunlap wrote:
> On Wed, 14 Nov 2007 15:08:47 +0100 Ingo Molnar wrote:
> > so please stop this "too busy and too noisy" nonsense already. It was 
> > nonsense 10 years ago and it's nonsense today. In 10 years the kernel 
> > grew from a 1 million lines codebase to an 8 million lines codebase, so 
> > what? Deal with it and be intelligent about filtering your information 
> > influx instead of imposing a hard pre-filtering criteria that restricts 
> > intelligent processing of information.
> 
> So you have a preferred method of handling email.  Please don't
> force it on the rest of us.

I'd be curious for any pointers on tools, actually.  I "read" (ok, skim)
lkml but still overlook relevant bug reports occasionally.
(Fortunately, between Trond and Andrew and others forwarding things it's
not actually a problem, but I'm still curious).

--b.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  7:46                         ` Denys Vlasenko
  2007-11-14 13:30                           ` Matthew Wilcox
@ 2007-11-14 18:27                           ` Kok, Auke
  1 sibling, 0 replies; 268+ messages in thread
From: Kok, Auke @ 2007-11-14 18:27 UTC (permalink / raw)
  To: Denys Vlasenko
  Cc: Adrian Bunk, Theodore Tso, Benoit Boissinot, Mark Lord,
	Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

Denys Vlasenko wrote:
> On Wednesday 14 November 2007 00:27, Adrian Bunk wrote:
>> You missed the following in my email:
>> "we slowly scare them away due to the many bug reports without any
>>  reaction."
>>
>> The problem is that bug reports take time. If you go away from easy
>> things like compile errors then even things like describing what does
>> no longer work, ideally producing a scenario where you can reproduce it
>> and verifying whether it was present in previous kernels can easily take
>> many hours that are spent before the initial bug report.
>>
>> If the bug report then gets ignored we discourage the person who sent
>> the bug report to do any work related to the kernel again.
> 
> Cannot agree more. I am in a similar position right now.
> My patch to aic7xxx driver was ubmitted four times
> with not much reaction from scsi guys.
> 
> Finally they replied and asked to rediff it against their
> git tree. I did that and sent patches back. No reply since then.
> 
> And mind you, the patch is not trying to do anything
> complex, it mostly moves code around, removes 'inline',
> adds 'const'. What should I think about it?

this has nothing to do with the bugs on bugzilla.

you're trying to send a janitor patch. It should be logical that the response to
that is not heated or receiving a joyous reception :)

If you have a problem getting your cleanup patch to the driver maintainer, send it
to the subsystem maintainer instead, or even the janitors, or even Adrian Bunk who
will gladly push it to everyone. Or, even to Andrew Morton who will carry it in
-mm for a while and then harrasses the subsystem maintainer to merge it for you!

Cheers,

Auke

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 10:07                         ` David Miller
  2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
@ 2007-11-14 19:44                           ` Russell King
  2007-11-16 22:16                           ` Use *poof* for linux-omap (Was: [BUG] New Kernel Bugs) Tony Lindgren
  2 siblings, 0 replies; 268+ messages in thread
From: Russell King @ 2007-11-14 19:44 UTC (permalink / raw)
  To: David Miller
  Cc: alsa-devel, netdev, linux-pcmcia, linux-kernel, protasnb,
	linux-ide, bugme-daemon, linux-input, akpm

On Wed, Nov 14, 2007 at 02:07:06AM -0800, David Miller wrote:
> From: Russell King <rmk+lkml@arm.linux.org.uk>
> Date: Wed, 14 Nov 2007 09:55:07 +0000
> 
> > On Tue, Nov 13, 2007 at 05:55:51PM -0800, David Miller wrote:
> > > I've created linux-arm@vger.kernel.org
> > 
> > By doing so you've just said (implicitly) that you can not tolerate
> > someone having a different opinion from your own.
> 
> I created a mailing list on a machine where I provide such services.
> 
> People can choose to use or not use the new list, it is their choice.
> 
> > While I accept *your* right to run *your* lists how you please, you
> > are unable to accept *my* right to run *my* lists how I see fit.
> 
> I didn't tell you to take your list down or to run it in some other
> way.  I didn't tell you to unsubscribe everyone and move them over
> to the new list either.

I didn't say that you were.

> I've provided an alternative, and people can pick and choose how they
> see fit.  I'm letting natural selection run it's course.  Are you
> able to cope with the fact that people might not want to use your
> list any longer?  Perhaps that is what bugs you so much about my
> giving people a alternative choice.

Absolutely, and if you'd have read my message you'd have seen that
I'd said effectively the same thing that you're saying here.

Having been flamed for not reading emails properly by AKPM shall
I flame you for not reading my emails properly?  Oh no, it's merely
human to occasionally have such misunderstandings.  Unless you're
rmk.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 13:24   ` Pavel Machek
  2007-11-14 14:14     ` Fabio Comolli
@ 2007-11-14 19:52     ` Russell King
  1 sibling, 0 replies; 268+ messages in thread
From: Russell King @ 2007-11-14 19:52 UTC (permalink / raw)
  To: Pavel Machek
  Cc: Andrew Morton, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	Natalie Protasevich, linux-ide, bugme-daemon, linux-input

On Wed, Nov 14, 2007 at 01:24:48PM +0000, Pavel Machek wrote:
> Hi!
> 
> > > Suspend to RAM resume hangs on a tickless (NO_HZ) kernel
> > > http://bugzilla.kernel.org/show_bug.cgi?id=9275
> > > Kernel: 2.6.23
> > > This is HP notebook nc6320 T2400 945GM
> > 
> > No response from developers
> 
> Maybe I'm optimistic, but I expected Ingo/Thomas to look after nohz
> problems. nohz=off highres=off fixes more than one suspend problem...
> 
> ...stuff I've seen with NOHZ even without suspend (cursor blinking
> irregulary) make me think that nohz perhaps should not be used in
> production just yet...

It appears that bug 9229 has been solved, and the reporter of that
bug now says that:

  If I unset NO_TZ suspend/resume works.
  If I set it suspend/resume doesn't works.

So I think this guy is now suffering from bug #9275

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 16:56                   ` Nick Piggin
@ 2007-11-14 19:54                     ` Linus Torvalds
  2007-11-14 22:22                       ` Heikki Orsila
  0 siblings, 1 reply; 268+ messages in thread
From: Linus Torvalds @ 2007-11-14 19:54 UTC (permalink / raw)
  To: Nick Piggin; +Cc: Andrew Morton, Christian Kujau, linux-kernel



On Wed, 14 Nov 2007, Nick Piggin wrote:
> 
> Not if you said their regression causing patches will get reverted unless it
> can be fixed for release.

Actually, I'm pretty happy reverting patches that cause regressions even 
if it *can* be "fixed for release". If there isn't a fix available within 
a day or two, it should get reverted.

The "fix" can then be re-applying the *fixed* patch - and at that point we 
should strive to require the person who re-submits the patch (with fixes) 
having to have an Ack from the person who found the problem in the first 
place, so that it's verified to actually fix things!

So I really would encourage people to send me emails like

	Please revert commit xyz, because it breaks abc, and there is no 
	fix available even though this was reported x days ago.

	I have verified that revert just that change fixes the issue.

and just make the "because it breaks abc" be specific and clear enough 
that I go "Ahh, ok, I'd better revert it".

Also, please notice the latter part of the suggestion above: even if 
somebody has bisected down their problem to a specific commit, I really 
*do* want to hear that actually undoing the commit on top of the current 
tree acually fixes it again, because sometimes that just isn't the case - 
sometimes you end up having various interactions that means that reverting 
a commit might simply not even work.

I have no trouble at all with reverting commits in general. I think 
regressions are serious.

So the problematic cases are the cases where:

 - the commit no longer reverts cleanly, or just otherwise introduces 
   other infrastructure that other commits that already got merged depend 
   on.

   So sometimes you actually need a patch along with the revert (Andrew 
   does that kind of thing anyway, since he works with patches regardless, 
   so the "needs a patch" case is obviously not limited to just the 
   problem cases)

 - more commonly: it's not entirely clear which commit actually caused the 
   problem.

but I *do* want to encourage people to revert (and ask other people to 
revert) much more aggressively. I personally try to revert things that 
people report regressions to me about very actively, unless I know 
somebody already has or is working on a fix.

				Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 14:08               ` Ingo Molnar
  2007-11-14 17:38                 ` Randy Dunlap
@ 2007-11-14 19:56                 ` David Miller
  2007-11-14 20:09                   ` James Bottomley
  2007-11-14 20:48                   ` Ingo Molnar
  1 sibling, 2 replies; 268+ messages in thread
From: David Miller @ 2007-11-14 19:56 UTC (permalink / raw)
  To: mingo
  Cc: rdunlap, akpm, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

From: Ingo Molnar <mingo@elte.hu>
Date: Wed, 14 Nov 2007 15:08:47 +0100

> In fact this thread is the very example: David points out that on netdev 
> some of those bugs were already discussed and resolved. Had it been all 
> on lkml we'd all be aware of it.

That's a rediculious argument.

One other reason these bugs are resolved, is that the networking
developers only need to subscribe to netdev and not have to listen to
all the noise on lkml.

People who want to manage bugs know what list to look on and
contact about problems.

Dumping even more crap on lkml is not the answer.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 19:56                 ` David Miller
@ 2007-11-14 20:09                   ` James Bottomley
  2007-11-14 20:54                     ` Ingo Molnar
  2007-11-14 20:48                   ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: James Bottomley @ 2007-11-14 20:09 UTC (permalink / raw)
  To: David Miller
  Cc: mingo, rdunlap, akpm, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, 2007-11-14 at 11:56 -0800, David Miller wrote:
> From: Ingo Molnar <mingo@elte.hu>
> Date: Wed, 14 Nov 2007 15:08:47 +0100
> 
> > In fact this thread is the very example: David points out that on netdev 
> > some of those bugs were already discussed and resolved. Had it been all 
> > on lkml we'd all be aware of it.
> 
> That's a rediculious argument.
> 
> One other reason these bugs are resolved, is that the networking
> developers only need to subscribe to netdev and not have to listen to
> all the noise on lkml.
> 
> People who want to manage bugs know what list to look on and
> contact about problems.
> 
> Dumping even more crap on lkml is not the answer.

I agree totally with David, and this goes for SCSI too.  If it's not
reported on linux-scsi, there's a significant chance of us missing the
bug report.  The fact that some people notice bugs go past on LKML and
forward them to linux-scsi is a happy accident and not necessarily
something to rely on.

LKML has 10-20x the traffic of linux-scsi and a much smaller signal to
noise ratio.  Having a specialist list where all the experts in the
field hangs out actually enhances our ability to fix bugs.

James
 


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 17:38                 ` Randy Dunlap
  2007-11-14 18:23                   ` J. Bruce Fields
@ 2007-11-14 20:16                   ` Ingo Molnar
  2007-11-14 20:29                     ` Randy Dunlap
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 20:16 UTC (permalink / raw)
  To: Randy Dunlap
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


* Randy Dunlap <rdunlap@xenotime.net> wrote:

> On Wed, 14 Nov 2007 15:08:47 +0100 Ingo Molnar wrote:
> 
> > 
> > * Randy Dunlap <rdunlap@xenotime.net> wrote:
> > 
> > > > (and this is in no way directed at the networking folks - it holds 
> > > > for all of us. I have one main complaint about networking: the 
> > > > separate netdev list is a bad idea - networking regressions should 
> > > > be discussed and fixed on lkml, like most other subsystems are. Any 
> > > > artificial split of the lk discussion space is bad.)
> > > 
> > > but here I disagree.  LKML is already too busy and noisy. Major 
> > > subsystems need their own discussion areas.
> > 
> > That's a stupid argument. We lose much more by forced isolation of 
> > discussion than what we win by having less traffic! It's _MUCH_ 
                                                        ^^^^^^^^^^^^
> > easier to narrow down information (by filter by threads, by topics, 
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > by people, etc.) than it is to gobble information together from 
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > various fractured sources. We learned it _again and again_ that 
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > isolation of kernel discussions causes bad things.
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > 
> > In fact this thread is the very example: David points out that on 
> > netdev some of those bugs were already discussed and resolved. Had 
> > it been all on lkml we'd all be aware of it.
> 
> or had <someone> been on netdev.

countered by the underlined sentences above, just in case you missed it.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 20:16                   ` Ingo Molnar
@ 2007-11-14 20:29                     ` Randy Dunlap
  2007-11-14 20:37                       ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Randy Dunlap @ 2007-11-14 20:29 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, 14 Nov 2007 21:16:39 +0100 Ingo Molnar wrote:


> countered by the underlined sentences above, just in case you missed it.

I didn't miss your claim.


---
~Randy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 20:29                     ` Randy Dunlap
@ 2007-11-14 20:37                       ` Ingo Molnar
  2007-11-14 21:05                         ` Randy Dunlap
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 20:37 UTC (permalink / raw)
  To: Randy Dunlap
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


* Randy Dunlap <rdunlap@xenotime.net> wrote:

> On Wed, 14 Nov 2007 21:16:39 +0100 Ingo Molnar wrote:
> 
> > countered by the underlined sentences above, just in case you missed 
> > it.
> 
> I didn't miss your claim.

ok, then you conceded it by not replying to it? good ;-)

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 19:56                 ` David Miller
  2007-11-14 20:09                   ` James Bottomley
@ 2007-11-14 20:48                   ` Ingo Molnar
  2007-11-14 21:05                     ` david
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 20:48 UTC (permalink / raw)
  To: David Miller
  Cc: rdunlap, akpm, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon


* David Miller <davem@davemloft.net> wrote:

> From: Ingo Molnar <mingo@elte.hu>
> Date: Wed, 14 Nov 2007 15:08:47 +0100
> 
> > In fact this thread is the very example: David points out that on netdev 
> > some of those bugs were already discussed and resolved. Had it been all 
> > on lkml we'd all be aware of it.
> 
> That's a rediculious argument.
> 
> One other reason these bugs are resolved, is that the networking 
> developers only need to subscribe to netdev and not have to listen to 
> all the noise on lkml.

what noise? If someone really wants networking discussions only, use 
this procmail rule:

  :0 HBc
          * .*net: *
          sched-patches

to separate it into an extra folder and use "net: " as an agreed upon 
Subject line if you really want to narrow things down. (But there would 
still be all the other mail just in case the developer has to look at 
the wider picture. There would be no "I'm only subscribed to netdev" 
excuse. )

but there should still be one central repository for all kernel 
discussions - just like there is one central repository for all kernel 
code.

> People who want to manage bugs know what list to look on and contact 
> about problems.

i think that's the problem. Developers (and here i dont mean you) who
want to do "development only", without being exposed to the global state
of the kernel and without being exposed to bugs. I think that's the
basic mindset difference. That is one of the factor that is causing
assymetric allocation of developers and the increasing detachment from
reality.

> Dumping even more crap on lkml is not the answer.

that "crap" that i'd like to see dumped upon lkml would be netdev 
traffic mainly - most of the other kernel development lists (and i'm 
subscribed to many of them) are low-traffic. netdev is the main reason 
why we cannot do a "one common discussion forum" approach.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 20:09                   ` James Bottomley
@ 2007-11-14 20:54                     ` Ingo Molnar
  0 siblings, 0 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-14 20:54 UTC (permalink / raw)
  To: James Bottomley
  Cc: David Miller, rdunlap, akpm, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon


* James Bottomley <James.Bottomley@HansenPartnership.com> wrote:

> On Wed, 2007-11-14 at 11:56 -0800, David Miller wrote:
> > From: Ingo Molnar <mingo@elte.hu>
> > Date: Wed, 14 Nov 2007 15:08:47 +0100
> > 
> > > In fact this thread is the very example: David points out that on netdev 
> > > some of those bugs were already discussed and resolved. Had it been all 
> > > on lkml we'd all be aware of it.
> > 
> > That's a rediculious argument.
> > 
> > One other reason these bugs are resolved, is that the networking 
> > developers only need to subscribe to netdev and not have to listen 
> > to all the noise on lkml.
> > 
> > People who want to manage bugs know what list to look on and contact 
> > about problems.
> > 
> > Dumping even more crap on lkml is not the answer.
> 
> I agree totally with David, and this goes for SCSI too.  If it's not 
> reported on linux-scsi, there's a significant chance of us missing the 
> bug report.  The fact that some people notice bugs go past on LKML and 
> forward them to linux-scsi is a happy accident and not necessarily 
> something to rely on.
> 
> LKML has 10-20x the traffic of linux-scsi and a much smaller signal to 
> noise ratio.  Having a specialist list where all the experts in the 
> field hangs out actually enhances our ability to fix bugs.

you are actually proving my point. People have to scan lkml for SCSI 
regressions _anyway_, because otherwise _you_ would miss them. In the 
case a user is fortunate enough to realize that a regression is SCSI 
related, and he is lucky enough to pre-select the SCSI mailing list in 
the first go, he might get a fix from you. That already reduces the 
number of useful bugreports by about an order of magnitude.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 20:48                   ` Ingo Molnar
@ 2007-11-14 21:05                     ` david
  0 siblings, 0 replies; 268+ messages in thread
From: david @ 2007-11-14 21:05 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: David Miller, rdunlap, akpm, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, 14 Nov 2007, Ingo Molnar wrote:

>> Dumping even more crap on lkml is not the answer.
>
> that "crap" that i'd like to see dumped upon lkml would be netdev
> traffic mainly - most of the other kernel development lists (and i'm
> subscribed to many of them) are low-traffic. netdev is the main reason
> why we cannot do a "one common discussion forum" approach.

hmm, how much work would it be to tweak the mail software on vger to have 
a linux-all@vger.kernel.org that got a copy of any linux-* list hosted by 
vger.

this would solve half the problem (people on linux-kernel not seeing 
discussions on the other lists)

David Lang

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 20:37                       ` Ingo Molnar
@ 2007-11-14 21:05                         ` Randy Dunlap
  0 siblings, 0 replies; 268+ messages in thread
From: Randy Dunlap @ 2007-11-14 21:05 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Andrew Morton, David Miller, protasnb, linux-kernel, netdev,
	alsa-devel, linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, 14 Nov 2007 21:37:37 +0100 Ingo Molnar wrote:

> ok, then you conceded it by not replying to it? good ;-)

No, I don't intend to carry on this discussion,
but I appreciate the smiley.

---
~Randy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 13:35                             ` Hannes Reinecke
@ 2007-11-14 21:39                               ` Denys Vlasenko
  2007-11-14 21:58                                 ` Gabriel C
  0 siblings, 1 reply; 268+ messages in thread
From: Denys Vlasenko @ 2007-11-14 21:39 UTC (permalink / raw)
  To: Hannes Reinecke, Matthew Wilcox
  Cc: Adrian Bunk, Theodore Tso, Andrew Morton, linux-kernel, protasnb,
	linux-ide, Benoit Boissinot, Mark Lord, Ingo Molnar,
	David Miller

hi Matthew,

On Wednesday 14 November 2007 06:35, Hannes Reinecke wrote:
> Matthew Wilcox wrote:
> > On Wed, Nov 14, 2007 at 12:46:20AM -0700, Denys Vlasenko wrote:
> >> Finally they replied and asked to rediff it against their
> >> git tree. I did that and sent patches back. No reply since then.
> >>
> >> And mind you, the patch is not trying to do anything
> >> complex, it mostly moves code around, removes 'inline',
> >> adds 'const'. What should I think about it?
> >
> > I'm waiting for an ACK/NAK from Hannes, the maintainer.  What should I
> > do?

You could have informed me about this, and I would talk to Hannes
myself. This would free up your mind from keeping track of this
particular patch.
Parallelize development, prevent things from being forgotten.


Hi Hannes,

> I haven't actually been able to test it here (too busy, sorry). If someone
> else confirms it does it's job then
>
> Acked-by: Hannes Reinecke <hare@suse.de>

It's not in my mailbox on this machine, gladly we have lkml archived
in the Net. Here is a positive tester report:

http://lkml.org/lkml/2007/10/15/168:

======================
Date	Mon, 15 Oct 2007 15:53:08 +0200
From	Gabriel C <>
Subject	Re: [PATCH 0/3] debloat aic7xxx and aic79xx drivers

>> Compile tested and applies cleanly to 2.6.23.
>> I don't have this hardware anymore and cannot run test these patches.
> 
> I can test these patches on an aic7892 controller later on today if you 
want.

Works fine for me tested on :

03:0e.0 SCSI storage controller [0100]: Adaptec AIC-7892P U160/m [9005:008f] 
(rev 02)

Gabriel
=======================

--
vda

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 21:39                               ` Denys Vlasenko
@ 2007-11-14 21:58                                 ` Gabriel C
  0 siblings, 0 replies; 268+ messages in thread
From: Gabriel C @ 2007-11-14 21:58 UTC (permalink / raw)
  To: Denys Vlasenko
  Cc: Hannes Reinecke, Matthew Wilcox, Adrian Bunk, Theodore Tso,
	Andrew Morton, linux-kernel, protasnb, linux-ide,
	Benoit Boissinot, Mark Lord, Ingo Molnar, David Miller

Denys Vlasenko wrote:
> hi Matthew,
> 
> On Wednesday 14 November 2007 06:35, Hannes Reinecke wrote:
>> Matthew Wilcox wrote:
>>> On Wed, Nov 14, 2007 at 12:46:20AM -0700, Denys Vlasenko wrote:
>>>> Finally they replied and asked to rediff it against their
>>>> git tree. I did that and sent patches back. No reply since then.
>>>>
>>>> And mind you, the patch is not trying to do anything
>>>> complex, it mostly moves code around, removes 'inline',
>>>> adds 'const'. What should I think about it?
>>> I'm waiting for an ACK/NAK from Hannes, the maintainer.  What should I
>>> do?
> 
> You could have informed me about this, and I would talk to Hannes
> myself. This would free up your mind from keeping track of this
> particular patch.
> Parallelize development, prevent things from being forgotten.
> 
> 
> Hi Hannes,
> 
>> I haven't actually been able to test it here (too busy, sorry). If someone
>> else confirms it does it's job then
>>
>> Acked-by: Hannes Reinecke <hare@suse.de>
> 
> It's not in my mailbox on this machine, gladly we have lkml archived
> in the Net. Here is a positive tester report:
> 
> http://lkml.org/lkml/2007/10/15/168:
> 
> ======================
> Date	Mon, 15 Oct 2007 15:53:08 +0200
> From	Gabriel C <>
> Subject	Re: [PATCH 0/3] debloat aic7xxx and aic79xx drivers
> 
>>> Compile tested and applies cleanly to 2.6.23.
>>> I don't have this hardware anymore and cannot run test these patches.
>> I can test these patches on an aic7892 controller later on today if you 
> want.
> 
> Works fine for me tested on :
> 
> 03:0e.0 SCSI storage controller [0100]: Adaptec AIC-7892P U160/m [9005:008f] 
> (rev 02)
> 
> Gabriel
> =======================

I still run the patches on a box with 2.6.23 and one with 2.6.24-rc1 without any problems.
Didn't tested rc2/current git but I can if is needed.

If you need an Tested-by.. let me know.
   
> 
> --
> vda


Gabriel

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 19:54                     ` Linus Torvalds
@ 2007-11-14 22:22                       ` Heikki Orsila
  2007-11-14 23:05                         ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Heikki Orsila @ 2007-11-14 22:22 UTC (permalink / raw)
  To: Linus Torvalds; +Cc: Nick Piggin, Andrew Morton, Christian Kujau, linux-kernel

On Wed, Nov 14, 2007 at 11:54:16AM -0800, Linus Torvalds wrote:
> Actually, I'm pretty happy reverting patches that cause regressions even 
> if it *can* be "fixed for release". If there isn't a fix available within 
> a day or two, it should get reverted.
> ...
> Also, please notice the latter part of the suggestion above: even if 
> somebody has bisected down their problem to a specific commit, I really 
> *do* want to hear that actually undoing the commit on top of the current 
> tree acually fixes it again, because sometimes that just isn't the case - 
> sometimes you end up having various interactions that means that reverting 
> a commit might simply not even work.

Ok. drivers/net/skge has been broken for several weeks. I have manually 
fixed the driver at each rc* release since then.

Please revert skge changes, the commit that broke driver is
7fb7ac241162dc51ec0f7644d4a97b2855213c32

See
	http://bugzilla.kernel.org/show_bug.cgi?id=9321

for more information. I think Stephen Hemminger is working on the skge 
fix, but it has been several days since I've heard anything from him.

-- 
Heikki Orsila			Barbie's law:
heikki.orsila@iki.fi		"Math is hard, let's go shopping!"
http://www.iki.fi/shd

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 22:22                       ` Heikki Orsila
@ 2007-11-14 23:05                         ` Linus Torvalds
  0 siblings, 0 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-14 23:05 UTC (permalink / raw)
  To: Heikki Orsila, Stephen Hemminger
  Cc: Nick Piggin, Andrew Morton, Christian Kujau, Linux Kernel Mailing List



On Thu, 15 Nov 2007, Heikki Orsila wrote:
> 
> See
> 	http://bugzilla.kernel.org/show_bug.cgi?id=9321
> 
> for more information.

That's a pretty unhelpful thing. It doesn't describe the breakage at all, 
so there is hardly much "more info". 

You've also apparently made all the attachements "octet-streams", so they 
are singularly painful to look at (ie no normal web-browser will show 
them, you have to save them to a file and look at them there). 

That said, I think I'll revert it, since it certainly fits the bill, but 
that's a really quite unreadable bug-report.

I finally found the actual description of the problem (by following 
multiple links), but really, if people want me to revert things, I would 
*strongly* suggest they make it *obvious* what's going on in the email to 
me that says "please revert".

Because quite frankly, if that email doesn't explain why something should 
be reverted (and just points to other things), it doesn't really cut it.

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Moderated list
  2007-11-14  9:47                                     ` Takashi Iwai
@ 2007-11-14 23:23                                       ` David Miller
  2007-11-15  6:09                                         ` Rene Herman
  0 siblings, 1 reply; 268+ messages in thread
From: David Miller @ 2007-11-14 23:23 UTC (permalink / raw)
  To: tiwai
  Cc: rene.herman, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, perex

From: Takashi Iwai <tiwai@suse.de>
Date: Wed, 14 Nov 2007 10:47:39 +0100

> I think alsa-user can stay as is.  It's no place for dragging many
> other addresses like alsa-devel.
> 
> BTW, I also prefer keeping the name alsa-devel@.  It's been so.

That's fine with me, I've changed it alsa-devel@vger.kernel.org

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 17:13                 ` Theodore Tso
                                     ` (2 preceding siblings ...)
  2007-11-13 17:56                   ` Adrian Bunk
@ 2007-11-14 23:23                   ` Daniel Barkalow
  2007-11-15 15:30                     ` Theodore Tso
  3 siblings, 1 reply; 268+ messages in thread
From: Daniel Barkalow @ 2007-11-14 23:23 UTC (permalink / raw)
  To: Theodore Tso
  Cc: Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Tue, 13 Nov 2007, Theodore Tso wrote:

> There are two parts to this.  One is a Ubuntu development kernel which
> we can give to large numbers of people to expand our testing pool.
> But if we don't do a better job of responding to bug reports that
> would be generated by expanded testing this won't necessarily help us.
> 
> The other an automated set of standard pre-built bisection points so
> that testers can more easily localize a bug down to a few hundred
> commits without needing to learn how to use "git bisect" (think Ubuntu
> users).

I don't see any reason that we couldn't have a tool accessible to Ubuntu 
users that does a real "git bisect". Git is really good at being scripted 
by fancy GUIs. It should be easy enough to have a drop down with all of 
the Ubuntu kernel package releases, where the user selects what works and 
what doesn't. Then the tool clones a git repository with flags to only get 
relevant parts, and then leads a bisect run, where it's also 
configuring, building, and installing the kernels (as a different grub 
entry), and providing instructions in general. Fundamentally, "git bisect" 
is a really low-interaction process: you tell it a couple of commits, and 
then it does stuff, and then you tell it "I tested, and it worked" or "I 
tested, and it had the problem" or "Something else went wrong", and it 
asks you something new. Other than that, it just takes time (and a build 
system hook, which this tool would handle for the kernel). Eventually, it 
tells you what to report, and you do so.

	-Daniel
*This .sig left intentionally blank*

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 18:23                   ` J. Bruce Fields
@ 2007-11-15  2:50                     ` Neil Brown
  2007-11-16  0:05                       ` J. Bruce Fields
  0 siblings, 1 reply; 268+ messages in thread
From: Neil Brown @ 2007-11-15  2:50 UTC (permalink / raw)
  To: J. Bruce Fields
  Cc: Randy Dunlap, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-input,
	bugme-daemon

On Wednesday November 14, bfields@fieldses.org wrote:
> On Wed, Nov 14, 2007 at 09:38:20AM -0800, Randy Dunlap wrote:
> > On Wed, 14 Nov 2007 15:08:47 +0100 Ingo Molnar wrote:
> > > so please stop this "too busy and too noisy" nonsense already. It was 
> > > nonsense 10 years ago and it's nonsense today. In 10 years the kernel 
> > > grew from a 1 million lines codebase to an 8 million lines codebase, so 
> > > what? Deal with it and be intelligent about filtering your information 
> > > influx instead of imposing a hard pre-filtering criteria that restricts 
> > > intelligent processing of information.
> > 
> > So you have a preferred method of handling email.  Please don't
> > force it on the rest of us.
> 
> I'd be curious for any pointers on tools, actually.  I "read" (ok, skim)
> lkml but still overlook relevant bug reports occasionally.
> (Fortunately, between Trond and Andrew and others forwarding things it's
> not actually a problem, but I'm still curious).

Virtual Folders.

I use VM mode in EMACS, but I believe some other mail readers have the
same functionality.
I have a virtual folder called "nfs" which shows me all mail in my
inbox which has the string 'nfs' or 'lockd' in a To, Cc, or Subject
field.  When I visit that folder, I see all mail about nfs, whether it
was sent to me personally, or to a relevant list, or to lkml.

Admittedly if someone doesn't bother to choose a meaningful Subject,
then I might miss that.  I think this mostly happens when Andrew sends
a "-mm" announcement, asked people to change the subject line when
following up, and someone follows up without changing the subject line
and say "NFS doesn't work any more".

I have another virtual folder which matches "md" and "raid" and
"mdadm" in any header (so when the people from coraid.com talk about
ATA over Ethernet, that gets badly filed, but it is a small cost).

Then I have the "bkernel" (boring kernel) folder for all mail from
lkml that doesn't mention nfs or raid or md, and isn't from or to
me.  That folder I skim every week or so and just read the juicy
debates and look for interesting tidbits from interesting people -
then delete the whole folder, mostly unread.

I don't think I could cope with mail without virtual folders.

NeilBrown

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14  0:34               ` Denys Vlasenko
@ 2007-11-15  3:06                 ` Neil Brown
  0 siblings, 0 replies; 268+ messages in thread
From: Neil Brown @ 2007-11-15  3:06 UTC (permalink / raw)
  To: Denys Vlasenko
  Cc: Mark Lord, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-input,
	bugme-daemon

On Tuesday November 13, vda.linux@googlemail.com wrote:
> On Tuesday 13 November 2007 07:08, Mark Lord wrote:
> > Ingo Molnar wrote:
> > ..
> >
> > > This is all QA-101 that _cannot be argued against on a rational basis_,
> > > it's just that these sorts of things have been largely ignored for
> > > years, in favor of the all-too-easy "open source means many eyeballs and
> > > that is our QA" answer, which is a _good_ answer but by far not the most
> > > intelligent answer! Today "many eyeballs" is simply not good enough and
> > > nature (and other OS projects) will route us around if we dont change.
> >
> > ..
> >
> > QA-101 and "many eyeballs" are not at all in opposition.
> > The latter is how we find out about bugs on uncommon hardware,
> > and the former is what we need to track them and overall quality.
> >
> > A HUGE problem I have with current "efforts", is that once someone
> > reports a bug, the onus seems to be 99% on the *reporter* to find
> > the exact line of code or commit.  Ghad what a repressive method.
> 
> This is the only method that scales.

That sounds overly hash, and the rest of you mail sounds much more
moderate and sensible - I can only assume you were using hyperbole??

Putting the "onus on the reporter" is simply not going to work unless
you have a business relationship.  In the community, we are all
volunteering our time (well, maybe my employer is volunteering my time
to do community support, but the effect is the same).

I would hope that the focus of developers is to empower bug reporters
to provide further information (and as has been said, "git bisect" is
a great empowerer).  Some people will be incredibly help, especially
if you ask politely and say thankyou.  Others won't for any of a
number of reasons - and maybe that means their bug won't get fixed.

To my eyes, the "only method that scales" is investing effort in
encouraging and training bug reporters.  Some of that effort might not
produce results, but when others among those you have encouraged start
answering the newbee questions on the list and save you the time, you
get a distinct feeling that it was all worth while.


I think we are in agreement - I just wanted to take issue with that
one sentence :-)  The rest is great.

NeilBrown

> 
> Developer has only 24 hours in each day, and sometimes he needs to eat,
> sleep, and maybe even pay attention to e.g. his kids.
> 
> But bug reporters are much more numerous and they have more
> hours in one day combined.
> 
> BUT - it means that developers should try to increase user base,
> not scare users away.
> 
> > And if the "developer" who broke the damn thing, or who at least
> > "claims" to be supporting that code, cannot "reproduce" the bug,
> > they drop it completely.
> 
> Developer should let reporter know that reporter needs to help
> a bit here. Sometimes a bit of hand holding is needed, but it
> pays off because you breed more qualified testers/bug reporters.
> 
> > Contrast that flawed approach with how Linus does things..
> > he thinks through the symptoms, matches them to the code,
> > and figures out what the few possibilities might be,
> > and feeds back some trial balloon patches for the bug reporter to try.
> >
> > MUCH better.
> >
> > And remember, *I'm* an old-time Linux kernel developer.. just think about
> > the people reporting bugs who haven't been around here since 1992..
> 
> Yes. Developers should not grow more and more unhelpful
> and arrogant towards their users just because inexperienced
> users send incomplete/poorly written bug reports.
> They need to provide help, not humiliate/ignore.
> 
> I think we agree here.
> --
> vda
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 21:56                   ` Christian Kujau
@ 2007-11-15  4:07                     ` Bron Gondwana
  2007-11-15  4:24                       ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-15  4:07 UTC (permalink / raw)
  To: Christian Kujau; +Cc: Andrew Morton, linux-kernel, torvalds

On Tue, Nov 13, 2007 at 10:56:01PM +0100, Christian Kujau wrote:
> On Tue, 13 Nov 2007, Andrew Morton wrote:
>> There are a number of process things we _could_ do.  Like
>> - have bugfix-only kernel releases
>
> Adrian Bunk does (did?) this with 2.6.16.x, although it always seemed to me 
> like an unrewarded one man show. AFAIK not even the big distros are begging 
> for bugfix-only versions, as they too want to have (sell) new features. 
> Mission critical systems might want to require such versions, but I guess 
> they're using heavily customized trees anyway.

And congratulations to him for that.  We almost entirely dropped 2.6.16,
but there's a regression some time since then that makes large MMAPed
files a major pain (specifically the dcc database clean takes about 5
minutes on 2.6.16 and about 12 hours on 2.6.20 or 2.6.23 series kernels)

But we keep putting off writing a small testcase that can repeat the
issue so we can bisect it - because it's working fine with 2.6.16 on
that machine.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
  2007-11-14 11:56                             ` David Miller
@ 2007-11-15  4:16                             ` Bron Gondwana
  2007-11-15  5:59                               ` Rene Herman
  1 sibling, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-15  4:16 UTC (permalink / raw)
  To: Rene Herman
  Cc: David Miller, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, Jaroslav Kysela, Takashi Iwai

On Wed, Nov 14, 2007 at 12:46:24PM +0100, Rene Herman wrote:
> On 14-11-07 11:07, David Miller wrote:
>
> Added Jaroslav and Takashi to the already extensive CC....
>
>> From: Russell King <rmk+lkml@arm.linux.org.uk>
>
>>> So, when are you creating a replacement alsa-devel mailing list on
>>> vger?  That's also subscribers-only.
>> The operative term is "alternative" rather than "replacement".
>> Perhaps this misunderstanding is what you're so upset about.
>> And yes, that alsa list bugs the crap out of me too.  I'm more than
>> happy to provide an alternative for that one as well.
>
> alsa-devel@alsa-project.org is not subscriber-only. Same as that arm list, 
> it's _moderated_ for non-subscribers and given that I and other moderators 
> have been doing our best to moderate quickly (I tend to stay logged in to 
> the moderation interface all day for example) what specifically bugged the 
> crap out of you? It's not something a poster needs to concern himself with.

Totally unrelated - I sent something to the kolab mailing list a couple
of days ago (it's moderated for non subscribers) informing them that I
had found the cause of some Cyrus bugs that they had problems with in
the past and providing a link to my post to the cyrus list with the
patches attached.

It sat in the moderation queue and then was rejected with "non
subscriber post to subscription only list".  Not only was the reponse a
day later when I had moved on to other things, but it got me really
pissed off that I had put some effort into providing a good quality post
that outlined the specific issues and how they applied to their project,
and had been summarily dismissed, probably without the effort being put
in.

There's no way for a non-subscriber to know in advance if the list they
are trying to post to will do that to them, completely negating the
effort put in to writing something worthwhile to inform that community.
It's insular, and it sucks.

So yeah, my attitude now is that the Kolab folks can go screw themselves
and track down the fix on their own or wait until I've convinced
upstream to accept the fixes (likely) and they have moved to the new
version (unlikely for a long time, and meanwhile they're missing out on
the performance increases that having a more stable skiplist library 
would give them)

I'm sure if I had something that I considered worth informing the ALSA
project of, I'd be wary of spending the same effort writing a good
post knowing it may be dropped in between the by a list moderator just
selecing all and bouncing them.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15  4:07                     ` Bron Gondwana
@ 2007-11-15  4:24                       ` Linus Torvalds
  2007-11-15  5:25                         ` Bron Gondwana
  0 siblings, 1 reply; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15  4:24 UTC (permalink / raw)
  To: Bron Gondwana; +Cc: Christian Kujau, Andrew Morton, linux-kernel



On Thu, 15 Nov 2007, Bron Gondwana wrote:
> 
> And congratulations to him for that.  We almost entirely dropped 2.6.16,
> but there's a regression some time since then that makes large MMAPed
> files a major pain (specifically the dcc database clean takes about 5
> minutes on 2.6.16 and about 12 hours on 2.6.20 or 2.6.23 series kernels)
> 
> But we keep putting off writing a small testcase that can repeat the
> issue so we can bisect it - because it's working fine with 2.6.16 on
> that machine.

Heh. I suspect you don't even need to bisect it.

The big difference with large mmap'ed files is that later kernels will 
actually track dirty ratios for dirty mmap'ed pages. Earlier kernels never 
did.

So in older kernels, you can dirty as much memory as you want, and the 
kernel will never try to write it back (well - "never" here means one of 
either (a) you ask it to with msync or (b) you run out of memory, when the 
kernel then totally falls down and the machine is essentially unusuable).

So *if* the symptom seems to be that the later kernels do a lot more IO, 
then try to change 

	/proc/sys/vm/dirty_[background_]ratio

which is just a percentage of memory (defaults to 5% for background and 
10% for foreground dirtying). Turn them both up a lot (say to 50 and 80 
percent respectively) and see if that makes a difference.

If so, you'll be the first one to officially even notice this change, I 
think.

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15  4:24                       ` Linus Torvalds
@ 2007-11-15  5:25                         ` Bron Gondwana
  2007-11-15  5:35                           ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-15  5:25 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton, linux-kernel

On Wed, Nov 14, 2007 at 08:24:53PM -0800, Linus Torvalds wrote:
> 
> 
> On Thu, 15 Nov 2007, Bron Gondwana wrote:
> > 
> > And congratulations to him for that.  We almost entirely dropped 2.6.16,
> > but there's a regression some time since then that makes large MMAPed
> > files a major pain (specifically the dcc database clean takes about 5
> > minutes on 2.6.16 and about 12 hours on 2.6.20 or 2.6.23 series kernels)
> > 
> > But we keep putting off writing a small testcase that can repeat the
> > issue so we can bisect it - because it's working fine with 2.6.16 on
> > that machine.
> 
> Heh. I suspect you don't even need to bisect it.
> 
> The big difference with large mmap'ed files is that later kernels will 
> actually track dirty ratios for dirty mmap'ed pages. Earlier kernels never 
> did.
> 
> So in older kernels, you can dirty as much memory as you want, and the 
> kernel will never try to write it back (well - "never" here means one of 
> either (a) you ask it to with msync or (b) you run out of memory, when the 
> kernel then totally falls down and the machine is essentially unusuable).
> 
> So *if* the symptom seems to be that the later kernels do a lot more IO, 
> then try to change 
> 
> 	/proc/sys/vm/dirty_[background_]ratio
> 
> which is just a percentage of memory (defaults to 5% for background and 
> 10% for foreground dirtying). Turn them both up a lot (say to 50 and 80 
> percent respectively) and see if that makes a difference.

>From our sysctl.conf:
# This should help reduce flushing on Cache::FastMmap files
vm.dirty_background_ratio = 50
vm.dirty_expire_centisecs = 9000
vm.dirty_ratio = 80
vm.dirty_writeback_centisecs = 3000

So we've already been running those settings for a while.  They didn't
help.

We also gave this thing its very own dedicated ServeRAID card and
associated RAID1 set of high speed SCSI drives (mainly because they
were just sitting there already attached to the machine and unused,
we don't love DCC that much) and it didn't help.  Helped the rest of
the machine now that the system drive wasn't being pegged 100% for
12 hours a day, but it didn't speed things up any.

It was making some pretty random little scattered changes all through
that file.  Hmm.. here's what the developers said about it:


  First dbclean creates a new dcc_db file by copying from the old file.
  As it copies, it decides whether each record is worth keeping.
  That involves looking up the checksums in the old hash table.  This
  is as almost afast a simple /bin/cp if the old dcc_db and dcc_db.hash
  files fit in RAM.

  The dbclean creates a new dcc_db.hash file.  This starts with
  creating an empty new dcc_db.hash file.  Then the new dcc_db and
  dcc_db.hash files are mapped into memory, and dbclean creates pointers
  to each checksum in the dcc_db file in the dcc_db.hash file.

  While dbclean is running, dccd unmaps everything and tries to stay out
  of the way.

 
> If so, you'll be the first one to officially even notice this change, I 
> think.

Yay for us.  Thankfully it doesn't affect Cyrus's MMAP usage (read only
with direct seek and write calls to change anything, then remap) or we
would have suffered pretty badly!

Guess we'd better get on to figuring building a simple test app.  The
mmap file that DCC uses is about 2Gb if that makes any difference:

-rw-r--r-- 1 dcc  dcc  2035138560 Nov 15 00:15 dcc_db
-rw-r--r-- 1 dcc  dcc   516612096 Nov 14 06:27 dcc_db.hash

The machine has 6Gb of memory and should be able to fit these
files fine:

[root@out1 hm]$ free
             total       used       free     shared    buffers     cached
Mem:       6232364    5758112     474252          0      41756    3002528
-/+ buffers/cache:    2713828    3518536
Swap:      2048248      74944    1973304


And here's what top says about the process:
      15   0 1914m  57m  41m D    5  1.0 346:07.79 dccd

This is on: 2.6.16.55-reiserfix-fai 
  (one small patch to reiserfs, and built with netboot support for FAI)


So yeah - we'll try to get a clearer idea of what it's doing, but the
knob twiddle didn't work for us.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15  5:25                         ` Bron Gondwana
@ 2007-11-15  5:35                           ` Linus Torvalds
  2007-11-15  5:53                             ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15  5:35 UTC (permalink / raw)
  To: Bron Gondwana; +Cc: Christian Kujau, Andrew Morton, linux-kernel



On Thu, 15 Nov 2007, Bron Gondwana wrote:
> 
> So we've already been running those settings for a while.  They didn't
> help.

Ok, so something else is up. If the mmap file is 2G, and you have 6G of 
RAM, you shouldn't be hitting the dirty limits with those setups.

Of course, it may still be that some accounting thing is simply off, and 
the dirty limits trigger *despite* all the proper config settings ;)

> Guess we'd better get on to figuring building a simple test app.

Yeah, if you have something that others can see in action, that is sure 
going to get more people to look at it. 

That said - I'm sincerely hoping that you're not running on a 32-bit 
kernel. Because if so, those percentages are percentages of *normal* 
memory, not highmem (that got changed at one point after people ran out of 
lowmem).

So even at 100% dirty limits, it won't let you dirty more than 1GB on the 
default 32-bit setup.

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15  5:35                           ` Linus Torvalds
@ 2007-11-15  5:53                             ` Linus Torvalds
  2007-11-15 11:50                               ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
  0 siblings, 1 reply; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15  5:53 UTC (permalink / raw)
  To: Bron Gondwana; +Cc: Christian Kujau, Andrew Morton, linux-kernel



On Wed, 14 Nov 2007, Linus Torvalds wrote:
> 
> So even at 100% dirty limits, it won't let you dirty more than 1GB on the 
> default 32-bit setup.

Side note: all of these are obviously still just heuristics. If you really 
*do* run on a 32-bit kernel, and you want to have the pain, I'm sure you 
can just disable the dirty limits with a one-liner kernel mod. And if it's 
useful enough, we can certainly expose flags like that.. Not that I expect 
that much anybody else will ever care, but it's not like it's wrong to 
expose the silly heuristics the kernel has to users that have very 
specific loads.

That said, I still do hope you aren't actually using HIGHMEM64G. I was 
really hoping that the people who had enough moolah to buy >4GB of RAM had 
long since also upgraded to a 64-bit machine ;)

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15  4:16                             ` Bron Gondwana
@ 2007-11-15  5:59                               ` Rene Herman
  2007-11-15 12:02                                 ` Bron Gondwana
  2007-11-15 13:17                                 ` Olivier Galibert
  0 siblings, 2 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-15  5:59 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: David Miller, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, Jaroslav Kysela, Takashi Iwai

On 15-11-07 05:16, Bron Gondwana wrote:

> Totally unrelated - I sent something to the kolab mailing list a couple

[ ... ]

> I'm sure if I had something that I considered worth informing the ALSA 
> project of, I'd be wary of spending the same effort writing a good post
> knowing it may be dropped in between the by a list moderator just 
> selecing all and bouncing them.

Totally unrelated indeed so why are spouting crap? If the kohab list has a 
problem take it up with them but keep ALSA out of it. alsa-devel has only 
ever moderated out spam -- nothing else.

ene

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Moderated list
  2007-11-14 23:23                                       ` Moderated list David Miller
@ 2007-11-15  6:09                                         ` Rene Herman
  0 siblings, 0 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-15  6:09 UTC (permalink / raw)
  To: David Miller, perex
  Cc: tiwai, rmk+lkml, alsa-devel, netdev, linux-pcmcia, linux-kernel,
	protasnb, linux-ide, bugme-daemon, linux-input, akpm

On 15-11-07 00:23, David Miller wrote:

> From: Takashi Iwai <tiwai@suse.de>

>> BTW, I also prefer keeping the name alsa-devel@.  It's been so.
> 
> That's fine with me, I've changed it alsa-devel@vger.kernel.org

Great, thanks. Jaroslav -- given that this list won't need moderation I'd 
consider it the main/only alsa-devel. The alsa-devel subscriber database was 
cleansed only a couple of months ago when moving from sourceforge so it 
should now be okay to just transfer all subscriptions.

Or maybe you're already moving things; mailman.alsa-project.org seems to be 
down at least....

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15 13:17                                 ` Olivier Galibert
@ 2007-11-15  9:34                                   ` Takashi Iwai
  0 siblings, 0 replies; 268+ messages in thread
From: Takashi Iwai @ 2007-11-15  9:34 UTC (permalink / raw)
  To: Olivier Galibert
  Cc: Rene Herman, Bron Gondwana, David Miller, rmk+lkml, alsa-devel,
	netdev, linux-pcmcia, linux-kernel, protasnb, linux-ide,
	bugme-daemon, linux-input, akpm, Jaroslav Kysela

At Thu, 15 Nov 2007 14:17:27 +0100,
Olivier Galibert wrote:
> 
> On Thu, Nov 15, 2007 at 06:59:34AM +0100, Rene Herman wrote:
> > Totally unrelated indeed so why are spouting crap? If the kohab list has a 
> > problem take it up with them but keep ALSA out of it. alsa-devel has only 
> > ever moderated out spam -- nothing else.
> 
> That is incorrect.  Hopefully it is the case now though, since my
> experience of the subject was years ago.

Yeah, it was really years ago that we once switched to the open list.
Funny that people never forget such a thing :)


Takashi

^ permalink raw reply	[flat|nested] 268+ messages in thread

* mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15  5:53                             ` Linus Torvalds
@ 2007-11-15 11:50                               ` Bron Gondwana
  2007-11-15 16:32                                 ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-15 11:50 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton, linux-kernel, robm

On Wed, Nov 14, 2007 at 09:53:38PM -0800, Linus Torvalds wrote:
> 
> 
> On Wed, 14 Nov 2007, Linus Torvalds wrote:
> > 
> > So even at 100% dirty limits, it won't let you dirty more than 1GB on the 
> > default 32-bit setup.
> 
> Side note: all of these are obviously still just heuristics. If you really 
> *do* run on a 32-bit kernel, and you want to have the pain, I'm sure you 
> can just disable the dirty limits with a one-liner kernel mod. And if it's 
> useful enough, we can certainly expose flags like that.. Not that I expect 
> that much anybody else will ever care, but it's not like it's wrong to 
> expose the silly heuristics the kernel has to users that have very 
> specific loads.
> 
> That said, I still do hope you aren't actually using HIGHMEM64G. I was 
> really hoping that the people who had enough moolah to buy >4GB of RAM had 
> long since also upgraded to a 64-bit machine ;)

I'm afraid we are, which probably explains it.

We have a bunch of 64 bit machines, but this particular machine
is one of our somewhat more ancient IBM x235 machines.  It's
got stacks of fast SCSI drives and a couple of hyperthreading
Xeons in it.  Very nice machine in its day, and very reliable
which is why we have kept them, even though at 6RU it chews
through disk space.

Unfortunately none of the 64 bit machines are world facing,
and we're running HIGHMEM64G on a bunch of machines both for
consistency value and because we only have one machine left
with only 2Gb.

I guess we'll be doing the one-liner kernel mod and testing
that then.  I'd certainly like to build a test case anyway
so I'm not spending too much time rebooting that machine,
it's also our outbound SMTP gateway.

And I'll keep in mind finding a 64 bit capable machine for
the role when I can.

Thanks for the feedback on this - I'll come back with more
details once we've done some testing, but this sounds likely,
and I don't think DCC is going to change how it works, so
we're stuck supporting it.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15  5:59                               ` Rene Herman
@ 2007-11-15 12:02                                 ` Bron Gondwana
  2007-11-15 12:26                                   ` Rene Herman
  2007-11-15 13:17                                 ` Olivier Galibert
  1 sibling, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-15 12:02 UTC (permalink / raw)
  To: Rene Herman
  Cc: Bron Gondwana, David Miller, rmk+lkml, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, protasnb, linux-ide, bugme-daemon,
	linux-input, akpm, Jaroslav Kysela, Takashi Iwai

On Thu, Nov 15, 2007 at 06:59:34AM +0100, Rene Herman wrote:
> On 15-11-07 05:16, Bron Gondwana wrote:
>
>> Totally unrelated - I sent something to the kolab mailing list a couple
>
> [ ... ]
>
>> I'm sure if I had something that I considered worth informing the ALSA 
>> project of, I'd be wary of spending the same effort writing a good post
>> knowing it may be dropped in between the by a list moderator just selecing 
>> all and bouncing them.
>
> Totally unrelated indeed so why are spouting crap? If the kohab list has a 
> problem take it up with them but keep ALSA out of it. alsa-devel has only 
> ever moderated out spam -- nothing else.

As an outsider to the list, how do I know what your policy will be
other than "I've been rejected out of hand by someone else's list, 
so my experience is that member only lists aren't willing to listen
to something I have to say unless I make the effort to sign up and
have yet another folder accumulating unread messages".  I don't.

Well, ok - maybe I do here since I've let myself be dragged in to
the debate.  Oops.

I get the same information from both project websites: "moderated
for non-members, public archives" - no way of knowing that ALSA
will accept me informing them of something they would be interested
without committing to reading or bit-bucketing their list.

The alternative is to subscribe just long enough to send something
and then unsubscribe again.... or cold-email a member and ask them
to pass a message along.  Or post and hope it doesn't get rejected,
not even knowing for a day or so.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15 12:02                                 ` Bron Gondwana
@ 2007-11-15 12:26                                   ` Rene Herman
  2007-11-15 13:00                                     ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Rene Herman @ 2007-11-15 12:26 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: David Miller, rmk+lkml, alsa-devel, netdev, linux-pcmcia,
	linux-kernel, protasnb, linux-ide, bugme-daemon, linux-input,
	akpm, Jaroslav Kysela, Takashi Iwai

On 15-11-07 13:02, Bron Gondwana wrote:

> I get the same information from both project websites: "moderated for
> non-members, public archives" - no way of knowing that ALSA will accept
> me informing them of something they would be interested without
> committing to reading or bit-bucketing their list.

Can you please just shelve this crap? You have a way of knowing that "ALSA 
will accept you" and that is knowing or assuming that the ALSA project 
doesn't consist of drooling retards.

When a project list goes to the difficulty of moderating non-subscribers it 
has made the explicit choice to _not_ become subscriber only. Then refusing 
valid non-subscribers after all makes no sense whatsoever. I'm sorry you got 
your feelings hurt by that other list but it was no doubt an accident; take 
it up with them.

Rene.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15 12:26                                   ` Rene Herman
@ 2007-11-15 13:00                                     ` Jörn Engel
  2007-11-15 14:29                                       ` Rene Herman
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-11-15 13:00 UTC (permalink / raw)
  To: Rene Herman
  Cc: Bron Gondwana, David Miller, rmk+lkml, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, protasnb, linux-ide, bugme-daemon,
	linux-input, akpm, Jaroslav Kysela, Takashi Iwai

On Thu, 15 November 2007 13:26:51 +0100, Rene Herman wrote:
> 
> Can you please just shelve this crap? You have a way of knowing that "ALSA 
> will accept you" and that is knowing or assuming that the ALSA project 
> doesn't consist of drooling retards.

Well, my experience with moderation has been that moderated mails are
stuck in some queue for weeks.  Two seperate lists, neither of them was
alsa.  If also is doing a better job, great.  But it still has to live
with the general reputation of non-subscriber moderation.

> When a project list goes to the difficulty of moderating non-subscribers it 
> has made the explicit choice to _not_ become subscriber only. Then refusing 
> valid non-subscribers after all makes no sense whatsoever. I'm sorry you 
> got your feelings hurt by that other list but it was no doubt an accident; 
> take it up with them.

Been there, done that.  In spite of people not being drooling retards,
the amount of time and effort they invest into either moderation or
improving the ruleset is quite limited.  Problems persist.

And even without mails being held hostage for weeks, every single
moderation mail is annoying.  Like the one I'm sure to receive after
sending this out.

Jörn

-- 
Joern's library part 5:
http://www.faqs.org/faqs/compression-faq/part2/section-9.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15  5:59                               ` Rene Herman
  2007-11-15 12:02                                 ` Bron Gondwana
@ 2007-11-15 13:17                                 ` Olivier Galibert
  2007-11-15  9:34                                   ` Takashi Iwai
  1 sibling, 1 reply; 268+ messages in thread
From: Olivier Galibert @ 2007-11-15 13:17 UTC (permalink / raw)
  To: Rene Herman
  Cc: Bron Gondwana, David Miller, rmk+lkml, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, protasnb, linux-ide, bugme-daemon,
	linux-input, akpm, Jaroslav Kysela, Takashi Iwai

On Thu, Nov 15, 2007 at 06:59:34AM +0100, Rene Herman wrote:
> Totally unrelated indeed so why are spouting crap? If the kohab list has a 
> problem take it up with them but keep ALSA out of it. alsa-devel has only 
> ever moderated out spam -- nothing else.

That is incorrect.  Hopefully it is the case now though, since my
experience of the subject was years ago.

  OG.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [alsa-devel] [BUG] New Kernel Bugs
  2007-11-15 13:00                                     ` Jörn Engel
@ 2007-11-15 14:29                                       ` Rene Herman
  0 siblings, 0 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-15 14:29 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Bron Gondwana, David Miller, rmk+lkml, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, protasnb, linux-ide, bugme-daemon,
	linux-input, akpm, Jaroslav Kysela, Takashi Iwai

On 15-11-07 14:00, Jörn Engel wrote:

> And even without mails being held hostage for weeks, every single 
> moderation mail is annoying.  Like the one I'm sure to receive after 
> sending this out.

Certainly. Upto this thread I wasn't actually aware the list was doing that. 
While it might be informative once, getting it each time quickly gets old. 
Don't know if mailman can do anything like it but I'd suggest anyone running 
a non-subscriber-moderation list configure it to send such messages at most 
once a <time-period> per address or some such. And just disable the message 
if it cannot do that.

Fortunately, alsa-devel is (almost) no longer such a list anyway as it's 
moving to vger. Hurrah. David -- thanks.

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-14 23:23                   ` Daniel Barkalow
@ 2007-11-15 15:30                     ` Theodore Tso
  2007-11-15 16:19                       ` Daniel Barkalow
  0 siblings, 1 reply; 268+ messages in thread
From: Theodore Tso @ 2007-11-15 15:30 UTC (permalink / raw)
  To: Daniel Barkalow
  Cc: Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Wed, Nov 14, 2007 at 06:23:34PM -0500, Daniel Barkalow wrote:
> I don't see any reason that we couldn't have a tool accessible to Ubuntu 
> users that does a real "git bisect". Git is really good at being scripted 
> by fancy GUIs. It should be easy enough to have a drop down with all of 
> the Ubuntu kernel package releases, where the user selects what works and 
> what doesn't.

It's possible users who haven't yet downloaded a git repository have
to surmount some obstacles that might cause them to lose interest.
First, they have to download some 190 megs of git repository, and if
they have a slow link, that can take a while, and then they have to
build each kernel, which can take a while.  A full kernel build with
everything selected can take good 30 minutes or more, and that's on a
fast dual-core machine with 4gigs of memory and 7200rpm disk drives.
On a slower, memory limited laptop, doing a single kernel build can
take more time than the user has patiences; multiply that by 7 or 8
build and test boots, and it starts to get tiresome.  

And then on top of that there are the issues about whether there is
enough support for dealing with hitting kernel revisions that fail due
to other bugs getting merged in during the -rc1 process, etc.

I agree that a tool that automated the bisection process and walked
the user through it would be helpful, but I believe it would be
possible for us do better.

						- Ted

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15 15:30                     ` Theodore Tso
@ 2007-11-15 16:19                       ` Daniel Barkalow
  2007-11-16  8:20                         ` Romano Giannetti
  0 siblings, 1 reply; 268+ messages in thread
From: Daniel Barkalow @ 2007-11-15 16:19 UTC (permalink / raw)
  To: Theodore Tso
  Cc: Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On Thu, 15 Nov 2007, Theodore Tso wrote:

> On Wed, Nov 14, 2007 at 06:23:34PM -0500, Daniel Barkalow wrote:
> > I don't see any reason that we couldn't have a tool accessible to Ubuntu 
> > users that does a real "git bisect". Git is really good at being scripted 
> > by fancy GUIs. It should be easy enough to have a drop down with all of 
> > the Ubuntu kernel package releases, where the user selects what works and 
> > what doesn't.
> 
> It's possible users who haven't yet downloaded a git repository have
> to surmount some obstacles that might cause them to lose interest.
> First, they have to download some 190 megs of git repository, and if
> they have a slow link, that can take a while, and then they have to
> build each kernel, which can take a while.

It should be possible for it to clone only the portion that they actually 
care about based on where the known-good version is. It should also (in 
theory, anyway) be possible to put off some amount of the download until 
it's actually going to be relevant.

> A full kernel build with everything selected can take good 30 minutes or 
> more, and that's on a fast dual-core machine with 4gigs of memory and 
> 7200rpm disk drives. On a slower, memory limited laptop, doing a single 
> kernel build can take more time than the user has patiences; multiply 
> that by 7 or 8 build and test boots, and it starts to get tiresome.

None of this is going to take as long, even on a slow link and a slow 
computer, as waiting for a response to a mailing list post. It'd annoy 
users who are specifically waiting for it, but if the interface is that 
the user says "kernel package X didn't work but the current kernel does", 
and it says "I'll let you know when I've got something to test", and the 
user watches a DVD, and afterward finds a message saying there's something 
to test, and tries it, and reports how it went, and the process repeats 
until it narrows it down to a single commit after a couple of days of the 
user getting occasional responses, it's not that different from asking for 
help online.

> And then on top of that there are the issues about whether there is
> enough support for dealing with hitting kernel revisions that fail due
> to other bugs getting merged in during the -rc1 process, etc.

Could have a distro-provided mask of things that aren't worth testing and 
possibly back-ported fixes for revisions in particular ranges.

> I agree that a tool that automated the bisection process and walked
> the user through it would be helpful, but I believe it would be
> possible for us do better.

That would probably help for giving the user something to try right away. 
I still think that the main cost to the user is the number of times that 
the user has to stop doing stuff to reboot with a kernel to test, whether 
the test kernels are available quickly from the distro site, slowly built 
locally, or slowly as suggested by humans helping online.

	-Daniel
*This .sig left intentionally blank*

^ permalink raw reply	[flat|nested] 268+ messages in thread

* [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-13 17:47       ` Mark Lord
@ 2007-11-15 16:32         ` Mark Lord
  2007-11-15 16:49           ` Ray Lee
                             ` (2 more replies)
  0 siblings, 3 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-15 16:32 UTC (permalink / raw)
  To: Thomas Gleixner, len.brown; +Cc: Andrew Morton, linux-kernel, linux-pm, rjw

I have been reporting this off and on since 2.6.23 was released.
This problem was not apparent up to perhaps 2.6.23-rc8,
but definitely became common in 2.6.23 and 2.6.23.1.

Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
of kernel time to complete.

Once in a while, it takes *much* longer, in the 14-20 second range.
These long events *seem* to be mostly after the notebook has been
in suspend for a longish time, but there's really nothing consistent here.

So git-bisect isn't going to work for this one.   I recently rebuilt the kernel
to include printk timestamps, and then it went 2 days without the issue happening,
until this morning (after an overnight suspend) finally.

The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB DDR2.
PCIe express chipset, ATI graphics, SATA hard drive.

00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X1400
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)

There's also a USB2 hub connected, with the Logitech mouse being the
only thing plugged into it at present.

The best clue I have of what is happening, other than that it was first
seen during the late 2.6.23-rc* series, are the following two sets of
kernel logs.  The first set is from a "normal" fast wake-up,
and the second set is from the "slow" wake-up seen this morning.

Both logs show the same information, in pretty much the same order.
The BIG difference is a bunch of unexplained pauses of exactly 1-second
each that occur during the slow wakeup.

The only other difference is that the SATA disk messages are placed
differently within the two logs.  I'm thinking on that one but it
doesn't look significant to me.

The real question is, why the 1-sec pauses?

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

HERE IS THE NORMAL RESUME LOG.


[  820.147914] CPU1 is down
[    0.355669] Back to C!
[    0.356120] Enabling non-boot CPUs ...
[    0.377167] SMP alternatives: switching to SMP code
[    0.378565] Booting processor 1/1 eip 3000
[    0.378568] CPU 1 irqstacks, hard=c0375000 soft=c0373000
[    0.389374] Initializing CPU#1
[    0.470225] Calibrating delay using timer specific routine.. 4324.85 BogoMIPS (lpj=7204571)
[    0.470235] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[    0.470244] monitor/mwait feature present.
[    0.470248] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.470252] CPU: L2 cache: 4096K
[    0.470255] CPU: Physical Processor ID: 0
[    0.470257] CPU: Processor Core ID: 1
[    0.470260] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[    0.471330] CPU1: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz stepping 06
[    0.471724] CPU1 is up
[    0.474787] Switched to high resolution mode on CPU 1
[    0.483415] PM: Writing back config space on device 0000:00:01.0 at offset a (was f, writing 0)
[    0.483422] PM: Writing back config space on device 0000:00:01.0 at offset 7 (was e0e0, writing 2000e0e0)
[    0.483428] PM: Writing back config space on device 0000:00:01.0 at offset 3 (was 10000, writing 10010)
[    0.483869] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.484224] PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 10b)
[    0.484244] PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was ffa7c004, writing efffc004)
[    0.484250] PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 10)
[    0.484258] PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100102)
[    0.484282] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
[    0.484292] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[    0.486711] PM: Writing back config space on device 0000:00:1c.0 at offset f (was 100, writing 20100)
[    0.486725] PM: Writing back config space on device 0000:00:1c.0 at offset 9 (was 10001, writing 1fff1)
[    0.486731] PM: Writing back config space on device 0000:00:1c.0 at offset 8 (was 0, writing fff0)
[    0.486738] PM: Writing back config space on device 0000:00:1c.0 at offset 7 (was 0, writing f0)
[    0.486744] PM: Writing back config space on device 0000:00:1c.0 at offset 6 (was 0, writing b0b00)
[    0.486753] PM: Writing back config space on device 0000:00:1c.0 at offset 3 (was 810000, writing 810010)
[    0.486761] PM: Writing back config space on device 0000:00:1c.0 at offset 1 (was 100000, writing 100007)
[    0.486782] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.486788] pciehp_resume ENTRY
[    0.486829] PM: Writing back config space on device 0000:00:1c.1 at offset f (was 200, writing 20200)
[    0.486841] PM: Writing back config space on device 0000:00:1c.1 at offset 9 (was 10001, writing 1fff1)
[    0.486848] PM: Writing back config space on device 0000:00:1c.1 at offset 8 (was 0, writing efc0efc0)
[    0.486854] PM: Writing back config space on device 0000:00:1c.1 at offset 7 (was 20000000, writing 200000f0)
[    0.486861] PM: Writing back config space on device 0000:00:1c.1 at offset 6 (was 0, writing c0c00)
[    0.486870] PM: Writing back config space on device 0000:00:1c.1 at offset 3 (was 810000, writing 810010)
[    0.486877] PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was 100000, writing 100107)
[    0.486898] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[    0.486903] pciehp_resume ENTRY
[    0.488916] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot hot-add
[    0.488920] pciehp: Cannot add device 0xc:0
[    0.488949] PM: Writing back config space on device 0000:00:1c.3 at offset f (was 400, writing 20400)
[    0.488963] PM: Writing back config space on device 0000:00:1c.3 at offset 9 (was 10001, writing e011e001)
[    0.488969] PM: Writing back config space on device 0000:00:1c.3 at offset 8 (was 0, writing efb0efa0)
[    0.488976] PM: Writing back config space on device 0000:00:1c.3 at offset 7 (was 0, writing d0d0)
[    0.488982] PM: Writing back config space on device 0000:00:1c.3 at offset 6 (was 0, writing e0d00)
[    0.488991] PM: Writing back config space on device 0000:00:1c.3 at offset 3 (was 810000, writing 810010)
[    0.488998] PM: Writing back config space on device 0000:00:1c.3 at offset 1 (was 100000, writing 100007)
[    0.489020] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    0.489025] pciehp_resume ENTRY
[    0.489063] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
[    0.489070] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    0.489121] usb usb1: root hub lost power or was reset
[    0.489144] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
[    0.489149] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 20
[    0.489157] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    0.489164] PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20b)
[    0.489178] PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1, writing bf61)
[    0.489214] usb usb2: root hub lost power or was reset
[    0.489236] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
[    0.489240] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21
[    0.489248] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    0.489255] PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 309)
[    0.489269] PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1, writing bf41)
[    0.489307] usb usb3: root hub lost power or was reset
[    0.489329] PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
[    0.489333] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22
[    0.489341] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    0.489348] PM: Writing back config space on device 0000:00:1d.3 at offset f (was 400, writing 407)
[    0.489363] PM: Writing back config space on device 0000:00:1d.3 at offset 8 (was 1, writing bf21)
[    0.489400] usb usb4: root hub lost power or was reset
[    0.489535] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
[    0.489543] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    0.489622] PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 100f1, writing 1fff1)
[    0.489629] PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was 90, writing ef90ef90)
[    0.489635] PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 2280e0f0, writing 228000f0)
[    0.489648] PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100007, writing 100107)
[    0.489668] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.489707] PM: Writing back config space on device 0000:00:1f.0 at offset 1 (was 2100007, writing 2100107)
[    0.489872] PM: Writing back config space on device 0000:00:1f.2 at offset f (was 200, writing 205)
[    0.489908] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    0.489915] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    0.489933] PM: Writing back config space on device 0000:00:1f.3 at offset f (was 200, writing 205)
[    0.489963] PM: Writing back config space on device 0000:00:1f.3 at offset 1 (was 2800001, writing 2800101)
[    0.489981] PM: Writing back config space on device 0000:01:00.0 at offset f (was 1ff, writing 104)
[    0.489996] PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 10)
[    0.490053] PM: Writing back config space on device 0000:0c:00.0 at offset f (was 100, writing 105)
[    0.490119] PM: Writing back config space on device 0000:0c:00.0 at offset 4 (was 0, writing efcff000)
[    0.490133] PM: Writing back config space on device 0000:0c:00.0 at offset 3 (was 0, writing 10)
[    0.490152] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100000, writing 100106)
[    0.490217] PM: Writing back config space on device 0000:03:00.0 at offset f (was 100, writing 105)
[    0.490236] PM: Writing back config space on device 0000:03:00.0 at offset 4 (was 0, writing ef9fe000)
[    0.490242] PM: Writing back config space on device 0000:03:00.0 at offset 3 (was 0, writing 4000)
[    0.490250] PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100000, writing 100106)
[    0.490267] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.492382] PM: Writing back config space on device 0000:03:01.0 at offset f (was 4020100, writing 4020103)
[    0.492403] PM: Writing back config space on device 0000:03:01.0 at offset 4 (was 0, writing ef9fd800)
[    0.492410] PM: Writing back config space on device 0000:03:01.0 at offset 3 (was 800000, writing 804000)
[    0.492417] PM: Writing back config space on device 0000:03:01.0 at offset 1 (was 2100000, writing 2100106)
[    0.493339] PM: Writing back config space on device 0000:03:01.1 at offset f (was 200, writing 209)
[    0.493361] PM: Writing back config space on device 0000:03:01.1 at offset 4 (was 0, writing ef9fd400)
[    0.493368] PM: Writing back config space on device 0000:03:01.1 at offset 3 (was 800000, writing 804000)
[    0.493376] PM: Writing back config space on device 0000:03:01.1 at offset 1 (was 2100000, writing 2100106)
[    0.493397] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 23
[    0.493428] PM: Writing back config space on device 0000:03:01.2 at offset f (was 200, writing 209)
[    0.493449] PM: Writing back config space on device 0000:03:01.2 at offset 4 (was 0, writing ef9fd500)
[    0.493459] PM: Writing back config space on device 0000:03:01.2 at offset 1 (was 2100000, writing 2100106)
[    0.493480] PM: Writing back config space on device 0000:03:01.3 at offset f (was 200, writing 209)
[    0.493500] PM: Writing back config space on device 0000:03:01.3 at offset 4 (was 0, writing ef9fd600)
[    0.493509] PM: Writing back config space on device 0000:03:01.3 at offset 1 (was 2100000, writing 2100102)
[    0.493530] PM: Writing back config space on device 0000:03:01.4 at offset f (was 200, writing 209)
[    0.493550] PM: Writing back config space on device 0000:03:01.4 at offset 4 (was 0, writing ef9fd700)
[    0.493559] PM: Writing back config space on device 0000:03:01.4 at offset 1 (was 2100000, writing 2100102)
[    0.493599] pciehp_resume ENTRY
[    0.493633] pciehp_resume ENTRY
[    0.503412] ata2.00: configured for UDMA/33
[    0.505628] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot hot-add
[    0.505633] pciehp: Cannot add device 0xc:0
[    0.505654] pciehp_resume ENTRY
[    0.505972] sd 0:0:0:0: [sda] Starting disk
[    0.601233] ata1.00: configured for UDMA/133
[    0.624888] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    0.624910] sd 0:0:0:0: [sda] Write Protect is off
[    0.624914] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.624943] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.801255] b44: eth0: Link is up at 100 Mbps, full duplex.
[    0.801260] b44: eth0: Flow control is off for TX and off for RX.
[    0.834760] Restarting tasks ... <6>usb 5-1: USB disconnect, address 17
[    0.972042] done.
[    0.998126] usb 5-1: new high speed USB device using ehci_hcd and address 21
[    1.121762] usb 5-1: configuration #1 chosen from 1 choice
[    1.121912] hub 5-1:1.0: USB hub found
[    1.121994] hub 5-1:1.0: 4 ports detected
[    1.224647] usb 5-7: USB disconnect, address 18
[    1.224651] usb 5-7.1: USB disconnect, address 20
[    1.334249] usb 5-7: new high speed USB device using ehci_hcd and address 22
[    1.479331] usb 5-7: configuration #1 chosen from 1 choice
[    1.479760] hub 5-7:1.0: USB hub found
[    1.480770] hub 5-7:1.0: 4 ports detected
[    1.782796] usb 5-1.4: new full speed USB device using ehci_hcd and address 23
[    1.884536] usb 5-1.4: configuration #1 chosen from 1 choice
[    2.079252] usb 5-7.1: new low speed USB device using ehci_hcd and address 24
[    2.166603] usb 5-7.1: configuration #1 chosen from 1 choice
[    2.169524] input: Logitech Optical USB Mouse as /class/input/input11
[    2.170506] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.7-7.1


* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

HERE IS THE SLOW RESUME LOG.  Note the 1-second pauses..


[ 3725.539992] CPU1 is down
[    0.354353] Back to C!
[    0.354793] Enabling non-boot CPUs ...
[    0.389097] SMP alternatives: switching to SMP code
[    0.389884] Booting processor 1/1 eip 3000
[    0.389886] CPU 1 irqstacks, hard=c0375000 soft=c0373000
[    0.401516] Initializing CPU#1
[    0.482207] Calibrating delay using timer specific routine.. 4324.78 BogoMIPS (lpj=7204462)
[    0.482212] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000000
[    0.482217] monitor/mwait feature present.
[    0.482219] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.482221] CPU: L2 cache: 4096K
[    0.482222] CPU: Physical Processor ID: 0
[    0.482223] CPU: Processor Core ID: 1
[    0.482225] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000000
[    0.482814] CPU1: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz stepping 06
[    0.483053] CPU1 is up
[    0.486165] Switched to high resolution mode on CPU 1
[    0.490338] PM: Writing back config space on device 0000:00:01.0 at offset a (was f, writing 0)
[    0.490342] PM: Writing back config space on device 0000:00:01.0 at offset 7 (was e0e0, writing 2000e0e0)
[    0.490345] PM: Writing back config space on device 0000:00:01.0 at offset 3 (was 10000, writing 10010)
[    0.490351] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.490605] PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 10b)
[    0.490626] PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was ffa7c004, writing efffc004)
[    0.490632] PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 10)
[    0.490640] PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100102)
[    0.490665] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
[    0.490674] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[    1.492418] PM: Writing back config space on device 0000:00:1c.0 at offset f (was 100, writing 20100)
[    1.492432] PM: Writing back config space on device 0000:00:1c.0 at offset 9 (was 10001, writing 1fff1)
[    1.492438] PM: Writing back config space on device 0000:00:1c.0 at offset 8 (was 0, writing fff0)
[    1.492445] PM: Writing back config space on device 0000:00:1c.0 at offset 7 (was 0, writing f0)
[    1.492451] PM: Writing back config space on device 0000:00:1c.0 at offset 6 (was 0, writing b0b00)
[    1.492460] PM: Writing back config space on device 0000:00:1c.0 at offset 3 (was 810000, writing 810010)
[    1.492468] PM: Writing back config space on device 0000:00:1c.0 at offset 1 (was 100000, writing 100007)
[    1.492490] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    1.492496] pciehp_resume ENTRY
[    1.492539] PM: Writing back config space on device 0000:00:1c.1 at offset f (was 200, writing 20200)
[    1.492552] PM: Writing back config space on device 0000:00:1c.1 at offset 9 (was 10001, writing 1fff1)
[    1.492559] PM: Writing back config space on device 0000:00:1c.1 at offset 8 (was 0, writing efc0efc0)
[    1.492565] PM: Writing back config space on device 0000:00:1c.1 at offset 7 (was 20000000, writing f0)
[    1.492572] PM: Writing back config space on device 0000:00:1c.1 at offset 6 (was 0, writing c0c00)
[    1.492581] PM: Writing back config space on device 0000:00:1c.1 at offset 3 (was 810000, writing 810010)
[    1.492588] PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was 100000, writing 100107)
[    1.492610] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[    1.492615] pciehp_resume ENTRY
[    1.493885] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot hot-add
[    1.493889] pciehp: Cannot add device 0xc:0
[    1.493916] PM: Writing back config space on device 0000:00:1c.3 at offset f (was 400, writing 20400)
[    1.493929] PM: Writing back config space on device 0000:00:1c.3 at offset 9 (was 10001, writing e011e001)
[    1.493936] PM: Writing back config space on device 0000:00:1c.3 at offset 8 (was 0, writing efb0efa0)
[    1.493942] PM: Writing back config space on device 0000:00:1c.3 at offset 7 (was 0, writing d0d0)
[    1.493949] PM: Writing back config space on device 0000:00:1c.3 at offset 6 (was 0, writing e0d00)
[    1.493958] PM: Writing back config space on device 0000:00:1c.3 at offset 3 (was 810000, writing 810010)
[    1.493966] PM: Writing back config space on device 0000:00:1c.3 at offset 1 (was 100000, writing 100007)
[    1.493987] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    1.493992] pciehp_resume ENTRY
[    1.494028] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
[    1.494036] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    1.494088] usb usb1: root hub lost power or was reset
[    1.494110] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
[    1.494114] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 20
[    1.494122] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    1.494130] PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20b)
[    1.494144] PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1, writing bf61)
[    1.494180] usb usb2: root hub lost power or was reset
[    1.494202] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
[    1.494206] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21
[    1.494214] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    1.494222] PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 309)
[    1.494236] PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1, writing bf41)
[    1.494273] usb usb3: root hub lost power or was reset
[    1.494295] PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
[    1.494299] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22
[    1.494307] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    1.494314] PM: Writing back config space on device 0000:00:1d.3 at offset f (was 400, writing 407)
[    1.494328] PM: Writing back config space on device 0000:00:1d.3 at offset 8 (was 1, writing bf21)
[    1.494365] usb usb4: root hub lost power or was reset
[    1.496460] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
[    1.496468] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    1.496534] PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 100f1, writing 1fff1)
[    1.496542] PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was 90, writing ef90ef90)
[    1.496551] PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 2280e0f0, writing 228000f0)
[    1.496570] PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100007, writing 100107)
[    1.496590] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    1.496629] PM: Writing back config space on device 0000:00:1f.0 at offset 1 (was 2100007, writing 2100107)
[    1.745307] PM: Writing back config space on device 0000:00:1f.2 at offset f (was 200, writing 205)
[    1.745344] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    1.745351] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    1.745369] PM: Writing back config space on device 0000:00:1f.3 at offset f (was 200, writing 205)
[    1.745406] PM: Writing back config space on device 0000:00:1f.3 at offset 1 (was 2800001, writing 2800101)
[    1.745430] PM: Writing back config space on device 0000:01:00.0 at offset f (was 1ff, writing 104)
[    1.745453] PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 10)
[    1.745514] PM: Writing back config space on device 0000:0c:00.0 at offset f (was 100, writing 105)
[    1.745584] PM: Writing back config space on device 0000:0c:00.0 at offset 4 (was 0, writing efcff000)
[    1.745600] PM: Writing back config space on device 0000:0c:00.0 at offset 3 (was 0, writing 10)
[    1.745623] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100000, writing 100106)
[    1.745709] PM: Writing back config space on device 0000:03:00.0 at offset f (was 100, writing 105)
[    1.745729] PM: Writing back config space on device 0000:03:00.0 at offset 4 (was 0, writing ef9fe000)
[    1.745735] PM: Writing back config space on device 0000:03:00.0 at offset 3 (was 0, writing 4000)
[    1.745743] PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100000, writing 100106)
[    1.745765] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[    2.753018] PM: Writing back config space on device 0000:03:01.0 at offset f (was 4020100, writing 4020103)
[    2.753038] PM: Writing back config space on device 0000:03:01.0 at offset 4 (was 0, writing ef9fd800)
[    2.753045] PM: Writing back config space on device 0000:03:01.0 at offset 3 (was 800000, writing 804000)
[    2.753053] PM: Writing back config space on device 0000:03:01.0 at offset 1 (was 2100000, writing 2100106)
[    3.756771] ata1.00: configured for UDMA/133
[    3.756818] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[    3.756836] sd 0:0:0:0: [sda] Write Protect is off
[    3.756840] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.756868] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.763813] b44: eth0: Link is up at 100 Mbps, full duplex.
[    4.763817] b44: eth0: Flow control is off for TX and off for RX.
[    4.764090] PM: Writing back config space on device 0000:03:01.1 at offset f (was 200, writing 209)
[    4.764111] PM: Writing back config space on device 0000:03:01.1 at offset 4 (was 0, writing ef9fd400)
[    4.764118] PM: Writing back config space on device 0000:03:01.1 at offset 3 (was 800000, writing 804000)
[    4.764126] PM: Writing back config space on device 0000:03:01.1 at offset 1 (was 2100000, writing 2100106)
[    4.764145] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 23
[    4.764171] PM: Writing back config space on device 0000:03:01.2 at offset f (was 200, writing 209)
[    4.764191] PM: Writing back config space on device 0000:03:01.2 at offset 4 (was 0, writing ef9fd500)
[    4.764201] PM: Writing back config space on device 0000:03:01.2 at offset 1 (was 2100000, writing 2100106)
[    4.764222] PM: Writing back config space on device 0000:03:01.3 at offset f (was 200, writing 209)
[    4.764242] PM: Writing back config space on device 0000:03:01.3 at offset 4 (was 0, writing ef9fd600)
[    4.764251] PM: Writing back config space on device 0000:03:01.3 at offset 1 (was 2100000, writing 2100102)
[    4.764273] PM: Writing back config space on device 0000:03:01.4 at offset f (was 200, writing 209)
[    4.764293] PM: Writing back config space on device 0000:03:01.4 at offset 4 (was 0, writing ef9fd700)
[    4.764303] PM: Writing back config space on device 0000:03:01.4 at offset 1 (was 2100000, writing 2100102)
[    4.764340] pciehp_resume ENTRY
[    4.764369] pciehp_resume ENTRY
[    5.765432] ata2.00: configured for UDMA/33
[    5.767529] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot hot-add
[    5.767532] pciehp: Cannot add device 0xc:0
[    5.767547] pciehp_resume ENTRY
[    5.767864] sd 0:0:0:0: [sda] Starting disk
[    7.750047] Restarting tasks ... done.
[    7.830571] usb 5-1: USB disconnect, address 21
[    8.126832] usb 5-1: new high speed USB device using ehci_hcd and address 25
[   10.230397] usb 5-1: configuration #1 chosen from 1 choice
[   10.230517] hub 5-1:1.0: USB hub found
[   10.230545] hub 5-1:1.0: 4 ports detected
[   10.281481] usb 5-7: USB disconnect, address 22
[   10.281489] usb 5-7.1: USB disconnect, address 24
[   10.889785] usb 5-7: new high speed USB device using ehci_hcd and address 26
[   11.658319] usb 5-7: configuration #1 chosen from 1 choice
[   11.658631] hub 5-7:1.0: USB hub found
[   11.658985] hub 5-7:1.0: 4 ports detected
[   13.190055] usb 5-1.4: new full speed USB device using ehci_hcd and address 27
[   13.961678] usb 5-1.4: configuration #1 chosen from 1 choice
[   14.171766] usb 5-7.1: new low speed USB device using ehci_hcd and address 28
[   14.295838] usb 5-7.1: configuration #1 chosen from 1 choice
[   14.298596] input: Logitech Optical USB Mouse as /class/input/input12
[   14.299091] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.7-7.1

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 11:50                               ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
@ 2007-11-15 16:32                                 ` Linus Torvalds
  2007-11-15 19:40                                   ` Peter Zijlstra
  2007-11-21 23:51                                   ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
  0 siblings, 2 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 16:32 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: Christian Kujau, Andrew Morton, Peter Zijlstra,
	Linux Kernel Mailing List, robm



On Thu, 15 Nov 2007, Bron Gondwana wrote:
> 
> I guess we'll be doing the one-liner kernel mod and testing
> that then.

The thing to look at is "get_dirty_limits()" in mm/page-writeback.c, and 
in this particular case it's the

	unsigned long available_memory = determine_dirtyable_memory();

that's going to bite you. In particular, note the

	x -= highmem_dirtyable_memory(x);

that we do in determine_dirtyable_memory().

So in this case, if you basically remove that line, it will allow all of 
memory to be dirtied (including highmem), and then the background_ratio 
will work on the whole 6GB.

HOWEVER! It's worth noting that we also have some other old legacy cruft 
there that may interfere with your code. In particular, if you look at the 
top of "get_dirty_limits()", it *also* does a

        unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
                                global_page_state(NR_ANON_PAGES)) * 100) /
                                        available_memory;

        dirty_ratio = vm_dirty_ratio;
        if (dirty_ratio > unmapped_ratio / 2)
                dirty_ratio = unmapped_ratio / 2;

and that whole "unmapped_ratio" comparison is probably bogus these days, 
since we now take the mapped dirty pages into account. That code harks 
back to the days before we did that, and dirty ratios only affected 
non-mapped pages.

And in particular, now that I look at it, I wonder if it can even go 
negative (because "available_memory" may be *smaller* than the 
NR_FILE_MAPPED|ANON_PAGES sum!).

We'll fix up a negative value anyway (because of the clamping of 
dirty_ratio to no less than 5), but the point is that the whole 
"unmapped_ratio" thing probably doesn't make sense any more, and may well 
make the dirty_ratio not work for you, because you may have a very small 
unmapped_ratio that effectively makes all dirty limits always clamp to a 
very small value.

So regardless, I think you may want to try the appended patch *first*.

If this patch makes a difference, please holler. I think it's the correct 
thing to do, but I'm not going to actually commit it without somebody 
saying that it makes a difference (and preferably Peter Zijlstra and 
Andrew acking it too).

Only *after* testing this change is it probably a good idea to test the 
real hack of then removing the highmem_dirtyable_memory() thing. 

Peter? Andrew?

		Linus

---
 mm/page-writeback.c |    8 --------
 1 files changed, 0 insertions(+), 8 deletions(-)

diff --git a/mm/page-writeback.c b/mm/page-writeback.c
index 81a91e6..d55cfca 100644
--- a/mm/page-writeback.c
+++ b/mm/page-writeback.c
@@ -297,20 +297,12 @@ get_dirty_limits(long *pbackground, long *pdirty, long *pbdi_dirty,
 {
 	int background_ratio;		/* Percentages */
 	int dirty_ratio;
-	int unmapped_ratio;
 	long background;
 	long dirty;
 	unsigned long available_memory = determine_dirtyable_memory();
 	struct task_struct *tsk;
 
-	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
-				global_page_state(NR_ANON_PAGES)) * 100) /
-					available_memory;
-
 	dirty_ratio = vm_dirty_ratio;
-	if (dirty_ratio > unmapped_ratio / 2)
-		dirty_ratio = unmapped_ratio / 2;
-
 	if (dirty_ratio < 5)
 		dirty_ratio = 5;
 

^ permalink raw reply related	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 16:32         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
@ 2007-11-15 16:49           ` Ray Lee
  2007-11-15 16:51             ` Mark Lord
  2007-11-15 18:14           ` Pavel Machek
  2007-11-18 16:10           ` Mark Lord
  2 siblings, 1 reply; 268+ messages in thread
From: Ray Lee @ 2007-11-15 16:49 UTC (permalink / raw)
  To: Mark Lord
  Cc: Thomas Gleixner, len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Nov 15, 2007 8:32 AM, Mark Lord <liml@rtr.ca> wrote:
> I have been reporting this off and on since 2.6.23 was released.
> This problem was not apparent up to perhaps 2.6.23-rc8,
> but definitely became common in 2.6.23 and 2.6.23.1.
>
> Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
> of kernel time to complete.
>
> Once in a while, it takes *much* longer, in the 14-20 second range.
> These long events *seem* to be mostly after the notebook has been
> in suspend for a longish time, but there's really nothing consistent here.
>
> So git-bisect isn't going to work for this one.   I recently rebuilt the kernel
> to include printk timestamps, and then it went 2 days without the issue happening,
> until this morning (after an overnight suspend) finally.
>
> The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB DDR2.
> PCIe express chipset, ATI graphics, SATA hard drive.
>
> 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
> 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
> 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
> 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
> 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
> 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
> 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 01)
> 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
> 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X1400
> 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
> 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
> 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
> 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
> 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
> 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
> 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
>
> There's also a USB2 hub connected, with the Logitech mouse being the
> only thing plugged into it at present.
>
> The best clue I have of what is happening, other than that it was first
> seen during the late 2.6.23-rc* series, are the following two sets of
> kernel logs.  The first set is from a "normal" fast wake-up,
> and the second set is from the "slow" wake-up seen this morning.
>
> Both logs show the same information, in pretty much the same order.
> The BIG difference is a bunch of unexplained pauses of exactly 1-second
> each that occur during the slow wakeup.
>
> The only other difference is that the SATA disk messages are placed
> differently within the two logs.  I'm thinking on that one but it
> doesn't look significant to me.
>
> The real question is, why the 1-sec pauses?

Well, and why the 1-second pauses eventually stop, too. Seems
interesting that they don't continue. Also, they're pretty much
dead-on one- and two-second pauses, with HZ accuracy. Is this with a
NO_HZ kernel?

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 16:49           ` Ray Lee
@ 2007-11-15 16:51             ` Mark Lord
  2007-11-15 16:53               ` Mark Lord
  0 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-15 16:51 UTC (permalink / raw)
  To: Ray Lee
  Cc: Mark Lord, Thomas Gleixner, len.brown, Andrew Morton,
	linux-kernel, linux-pm, rjw

Ray Lee wrote:
> On Nov 15, 2007 8:32 AM, Mark Lord <liml@rtr.ca> wrote:
>> I have been reporting this off and on since 2.6.23 was released.
>> This problem was not apparent up to perhaps 2.6.23-rc8,
>> but definitely became common in 2.6.23 and 2.6.23.1.
>>
>> Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
>> of kernel time to complete.
>>
>> Once in a while, it takes *much* longer, in the 14-20 second range.
>> These long events *seem* to be mostly after the notebook has been
>> in suspend for a longish time, but there's really nothing consistent here.
>>
>> So git-bisect isn't going to work for this one.   I recently rebuilt the kernel
>> to include printk timestamps, and then it went 2 days without the issue happening,
>> until this morning (after an overnight suspend) finally.
>>
>> The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB DDR2.
>> PCIe express chipset, ATI graphics, SATA hard drive.
>>
>> 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
>> 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
>> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
>> 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
>> 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
>> 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
>> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
>> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
>> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
>> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
>> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
>> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
>> 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
>> 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 01)
>> 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
>> 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X1400
>> 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
>> 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
>> 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
>> 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
>> 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
>> 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
>> 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
>>
>> There's also a USB2 hub connected, with the Logitech mouse being the
>> only thing plugged into it at present.
>>
>> The best clue I have of what is happening, other than that it was first
>> seen during the late 2.6.23-rc* series, are the following two sets of
>> kernel logs.  The first set is from a "normal" fast wake-up,
>> and the second set is from the "slow" wake-up seen this morning.
>>
>> Both logs show the same information, in pretty much the same order.
>> The BIG difference is a bunch of unexplained pauses of exactly 1-second
>> each that occur during the slow wakeup.
>>
>> The only other difference is that the SATA disk messages are placed
>> differently within the two logs.  I'm thinking on that one but it
>> doesn't look significant to me.
>>
>> The real question is, why the 1-sec pauses?
> 
> Well, and why the 1-second pauses eventually stop, too. Seems
> interesting that they don't continue. Also, they're pretty much
> dead-on one- and two-second pauses, with HZ accuracy. Is this with a
> NO_HZ kernel?
..

Yes, A NO_HZ kernel.  Full config follows:

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24-rc2-git4
# Wed Nov 14 14:19:45 2007
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_CGROUPS is not set
# CONFIG_FAIR_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_SLUB_DEBUG is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MCORE2=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_XADD=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_HPET_TIMER=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_MCE is not set
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
CONFIG_I8K=m
CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=m
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_3G_OPT is not set
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_2G_OPT is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_IRQBALANCE is not set
# CONFIG_SECCOMP is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_300=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=300
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
# CONFIG_COMPAT_VDSO is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION="/dev/sda3"
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_FAN=m
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
# CONFIG_ACPI_SBS is not set
# CONFIG_APM is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
# CONFIG_X86_SPEEDSTEP_SMI is not set
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
# CONFIG_X86_E_POWERSAVER is not set

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_HT_IRQ is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_PCCARD is not set
CONFIG_HOTPLUG_PCI=m
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
# CONFIG_HOTPLUG_PCI_ACPI is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=m
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
CONFIG_NET_SCHED=y

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RR=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
# CONFIG_NET_ACT_NAT is not set
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
# CONFIG_NET_CLS_POLICE is not set
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_SCH_FIFO=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIUART_LL=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y

#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_NL80211=y
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
CONFIG_MAC80211_RCSIMPLE=y
# CONFIG_MAC80211_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=4
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
CONFIG_EEPROM_93CX6=m
# CONFIG_SGI_IOC4 is not set
CONFIG_TIFM_CORE=m
# CONFIG_TIFM_7XX1 is not set
# CONFIG_FUJITSU_LAPTOP is not set
# CONFIG_MSI_LAPTOP is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
# CONFIG_IDE is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
CONFIG_ATA_PIIX=y
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
CONFIG_SATA_QSTOR=m
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
CONFIG_SATA_SIL24=m
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CS5535 is not set
# CONFIG_PATA_CS5536 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
# CONFIG_MD_LINEAR is not set
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID456 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_SBP2=m
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_IFB is not set
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_FIXED_MII_1000_FDX=y
CONFIG_FIXED_MII_AMNT=1
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_B44=m
CONFIG_B44_PCI_AUTOSELECT=y
CONFIG_B44_PCICORE_AUTOSELECT=y
CONFIG_B44_PCI=y
# CONFIG_FORCEDETH is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
# CONFIG_R8169_NAPI is not set
# CONFIG_R8169_VLAN is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set

#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
# CONFIG_LIBERTAS is not set
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
CONFIG_USB_ZD1201=m
CONFIG_RTL8187=m
# CONFIG_ADM8211 is not set
# CONFIG_P54_COMMON is not set
# CONFIG_IWLWIFI is not set
# CONFIG_HOSTAP is not set
CONFIG_BCM43XX=m
# CONFIG_BCM43XX_DEBUG is not set
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_B43=m
CONFIG_B43_PCI_AUTOSELECT=y
CONFIG_B43_PCICORE_AUTOSELECT=y
CONFIG_B43_RFKILL=y
# CONFIG_B43_DEBUG is not set
CONFIG_B43_DMA=y
CONFIG_B43_PIO=y
CONFIG_B43_DMA_AND_PIO_MODE=y
# CONFIG_B43_DMA_MODE is not set
# CONFIG_B43_PIO_MODE is not set
CONFIG_B43LEGACY=m
CONFIG_B43LEGACY_PCI_AUTOSELECT=y
CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
# CONFIG_B43LEGACY_DEBUG is not set
CONFIG_B43LEGACY_DMA=y
CONFIG_B43LEGACY_PIO=y
CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
# CONFIG_B43LEGACY_DMA_MODE is not set
# CONFIG_B43LEGACY_PIO_MODE is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set
# CONFIG_RT2X00 is not set

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
# CONFIG_USB_NET_MCS7830 is not set
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_USB_NET_ZAURUS=m
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOL2TP=m
# CONFIG_SLIP is not set
CONFIG_SLHC=m
# CONFIG_NET_FC is not set
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
CONFIG_INPUT_POLLDEV=m

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_EVBUG=m

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
# CONFIG_MOUSE_PS2_LIFEBOOK is not set
# CONFIG_MOUSE_PS2_TRACKPOINT is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_ATLAS_BTNS is not set
CONFIG_INPUT_ATI_REMOTE=m
CONFIG_INPUT_ATI_REMOTE2=m
CONFIG_INPUT_KEYSPAN_REMOTE=m
# CONFIG_INPUT_POWERMATE is not set
CONFIG_INPUT_YEALINK=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
CONFIG_FIX_EARLYCON_MEM=y
# CONFIG_SERIAL_8250_PCI is not set
# CONFIG_SERIAL_8250_PNP is not set
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
# CONFIG_HW_RANDOM_AMD is not set
# CONFIG_HW_RANDOM_GEODE is not set
# CONFIG_HW_RANDOM_VIA is not set
CONFIG_NVRAM=m
# CONFIG_RTC is not set
CONFIG_GEN_RTC=y
CONFIG_GEN_RTC_X=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
# CONFIG_WATCHDOG is not set

#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
CONFIG_SSB_SILENT=y
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
# CONFIG_DAB is not set

#
# Graphics support
#
CONFIG_AGP=m
# CONFIG_AGP_ALI is not set
CONFIG_AGP_ATI=m
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=m
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=m
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=m
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
# CONFIG_FB_HECUBA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_LE80578 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_CORGI is not set
# CONFIG_BACKLIGHT_PROGEAR is not set

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=m
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_LOGO is not set

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_AC97_CODEC=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
CONFIG_SND_AD1889=m
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_HDA_INTEL=m
# CONFIG_SND_HDA_HWDEP is not set
CONFIG_SND_HDA_CODEC_REALTEK=y
CONFIG_SND_HDA_CODEC_ANALOG=y
CONFIG_SND_HDA_CODEC_SIGMATEL=y
CONFIG_SND_HDA_CODEC_VIA=y
CONFIG_SND_HDA_CODEC_ATIHDMI=y
CONFIG_SND_HDA_CODEC_CONEXANT=y
CONFIG_SND_HDA_CODEC_CMEDIA=y
CONFIG_SND_HDA_CODEC_SI3054=y
CONFIG_SND_HDA_GENERIC=y
CONFIG_SND_HDA_POWER_SAVE=y
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=10
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_AC97_POWER_SAVE=y
CONFIG_SND_AC97_POWER_SAVE_DEFAULT=10

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
CONFIG_SND_USB_CAIAQ=m
# CONFIG_SND_USB_CAIAQ_INPUT is not set

#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set

#
# SoC Audio support for SuperH
#

#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
# CONFIG_SOUND_SSCAPE is not set
CONFIG_SOUND_VMIDI=m
# CONFIG_SOUND_TRIX is not set
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
# CONFIG_SOUND_PAS is not set
# CONFIG_SOUND_PSS is not set
CONFIG_SOUND_SB=m
# CONFIG_SOUND_YM3812 is not set
CONFIG_SOUND_UART6850=m
# CONFIG_SOUND_AEDSP16 is not set
# CONFIG_SOUND_KAHLUA is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_HID_DEBUG is not set
CONFIG_HIDRAW=y

#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
CONFIG_USB_PERSIST=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_U132_HCD is not set
CONFIG_USB_SL811_HCD=m
# CONFIG_USB_R8A66597_HCD is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_STORAGE_KARMA is not set
CONFIG_USB_LIBUSUAL=y

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y

#
# USB port drivers
#

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_CH341=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
# CONFIG_USB_SERIAL_HP4X is not set
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
# CONFIG_USB_SERIAL_DEBUG is not set
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
# CONFIG_USB_BERRY_CHARGE is not set
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
# CONFIG_USB_PHIDGET is not set
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
# CONFIG_USB_APPLEDISPLAY is not set
CONFIG_USB_SISUSBVGA=m
# CONFIG_USB_SISUSBVGA_CON is not set
CONFIG_USB_LD=m
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
CONFIG_USB_TEST=m

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set

#
# MMC/SD Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y
# CONFIG_SDIO_UART is not set

#
# MMC/SD Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
CONFIG_MMC_RICOH_MMC=m
# CONFIG_MMC_WBSD is not set
CONFIG_MMC_TIFM_SD=m
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
CONFIG_RTC_DRV_TEST=m

#
# I2C RTC drivers
#
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1374=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_MAX6900=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
# CONFIG_RTC_DRV_M41T80 is not set

#
# SPI RTC drivers
#

#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
CONFIG_RTC_DRV_DS1553=m
# CONFIG_RTC_DRV_STK17TA8 is not set
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_M48T86=m
# CONFIG_RTC_DRV_M48T59 is not set
CONFIG_RTC_DRV_V3020=m

#
# on-CPU RTC drivers
#
CONFIG_DMADEVICES=y

#
# DMA Devices
#
CONFIG_INTEL_IOATDMA=m
CONFIG_DMA_ENGINE=y

#
# DMA Clients
#
CONFIG_NET_DMA=y
CONFIG_DCA=m
# CONFIG_VIRTUALIZATION is not set

#
# Userspace I/O
#
CONFIG_UIO=m
# CONFIG_UIO_CIF is not set

#
# File systems
#
CONFIG_EXT2_FS=m
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
CONFIG_NLS_CODEPAGE_863=m
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
# CONFIG_INSTRUMENTATION is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
CONFIG_TIMER_STATS=y
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_DEBUG_SG=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_FORCED_INLINING is not set
CONFIG_BOOT_PRINTK_DELAY=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SAMPLES is not set
# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Page alloc debug is incompatible with Software Suspend on i386
#
# CONFIG_DEBUG_RODATA is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_HMAC=m
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
# CONFIG_CRYPTO_XTS is not set
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_TWOFISH_586=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
# CONFIG_CRYPTO_TEST is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_HW is not set

#
# Library routines
#
CONFIG_BITREVERSE=m
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=m
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 16:51             ` Mark Lord
@ 2007-11-15 16:53               ` Mark Lord
  0 siblings, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-15 16:53 UTC (permalink / raw)
  To: Ray Lee
  Cc: Mark Lord, Thomas Gleixner, len.brown, Andrew Morton,
	linux-kernel, linux-pm, rjw

Mark Lord wrote:
> Ray Lee wrote:
>..
>>> The real question is, why the 1-sec pauses?
>>
>> Well, and why the 1-second pauses eventually stop, too. Seems
>> interesting that they don't continue. Also, they're pretty much
>> dead-on one- and two-second pauses, with HZ accuracy. Is this with a
>> NO_HZ kernel?
> ..
> 
> Yes, A NO_HZ kernel.  Full config follows:
..

Blah.. that was for the wrong kernel.

Here is the correct .config that was in use for both suspend logs:


#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.23.1
# Wed Nov 14 09:41:54 2007
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
CONFIG_BLK_DEV_BSG=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"

#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_PARAVIRT is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MCORE2=y
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_XADD=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_HPET_TIMER=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_MCE is not set
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
CONFIG_I8K=m
CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=m
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_3G_OPT is not set
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_2G_OPT is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_IRQBALANCE is not set
# CONFIG_SECCOMP is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_300=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=300
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
# CONFIG_COMPAT_VDSO is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION="/dev/sda3"
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_FAN=m
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
# CONFIG_ACPI_SBS is not set
# CONFIG_APM is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
# CONFIG_X86_SPEEDSTEP_SMI is not set
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
# CONFIG_X86_E_POWERSAVER is not set

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
# CONFIG_HT_IRQ is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
CONFIG_HOTPLUG_PCI=m
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
# CONFIG_HOTPLUG_PCI_ACPI is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=m
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_FIFO=y

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RR=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
# CONFIG_NET_CLS_POLICE is not set
# CONFIG_NET_CLS_IND is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y

#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
# CONFIG_MAC80211_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=4
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
CONFIG_EEPROM_93CX6=m
# CONFIG_SGI_IOC4 is not set
CONFIG_TIFM_CORE=m
# CONFIG_TIFM_7XX1 is not set
# CONFIG_MSI_LAPTOP is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
CONFIG_IDE=m
CONFIG_IDE_MAX_HWIFS=2
CONFIG_BLK_DEV_IDE=m

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=m
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDECD is not set
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_BLK_DEV_IDEACPI is not set
CONFIG_IDE_TASK_IOCTL=y
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
# CONFIG_BLK_DEV_IDEPCI is not set
# CONFIG_IDEPCI_PCIBUS_ORDER is not set
# CONFIG_IDE_ARM is not set
# CONFIG_BLK_DEV_IDEDMA is not set
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
CONFIG_ATA_PIIX=y
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
CONFIG_SATA_QSTOR=m
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
CONFIG_SATA_SIL24=m
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CS5535 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
# CONFIG_MD_LINEAR is not set
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID456 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_SBP2=m
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_IFB is not set
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_ICPLUS_PHY is not set
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_B44=m
# CONFIG_FORCEDETH is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set

#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
# CONFIG_LIBERTAS is not set
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
CONFIG_USB_ZD1201=m
CONFIG_RTL8187=m
# CONFIG_HOSTAP is not set
CONFIG_BCM43XX=m
# CONFIG_BCM43XX_DEBUG is not set
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET_MII=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
# CONFIG_USB_NET_MCS7830 is not set
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_USB_NET_ZAURUS=m
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOL2TP=m
# CONFIG_SLIP is not set
CONFIG_SLHC=m
# CONFIG_NET_FC is not set
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
CONFIG_INPUT_POLLDEV=m

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_EVBUG=m

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
# CONFIG_MOUSE_PS2_LIFEBOOK is not set
# CONFIG_MOUSE_PS2_TRACKPOINT is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_ATLAS_BTNS is not set
CONFIG_INPUT_ATI_REMOTE=m
CONFIG_INPUT_ATI_REMOTE2=m
CONFIG_INPUT_KEYSPAN_REMOTE=m
# CONFIG_INPUT_POWERMATE is not set
CONFIG_INPUT_YEALINK=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
CONFIG_FIX_EARLYCON_MEM=y
# CONFIG_SERIAL_8250_PCI is not set
# CONFIG_SERIAL_8250_PNP is not set
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
# CONFIG_HW_RANDOM_AMD is not set
# CONFIG_HW_RANDOM_GEODE is not set
# CONFIG_HW_RANDOM_VIA is not set
CONFIG_NVRAM=m
# CONFIG_RTC is not set
CONFIG_GEN_RTC=y
CONFIG_GEN_RTC_X=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
CONFIG_AGP=m
# CONFIG_AGP_ALI is not set
CONFIG_AGP_ATI=m
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=m
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=m
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set

#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
# CONFIG_DAB is not set

#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_PROGEAR is not set

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=m
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
# CONFIG_FB_HECUBA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_LE80578 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=m
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_LOGO is not set

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_AC97_CODEC=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
CONFIG_SND_AD1889=m
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_HDA_INTEL=m
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
CONFIG_SND_AC97_POWER_SAVE=y

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
CONFIG_SND_USB_CAIAQ=m
# CONFIG_SND_USB_CAIAQ_INPUT is not set

#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set

#
# SoC Audio support for SuperH
#

#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_TRACEINIT is not set
# CONFIG_SOUND_DMAP is not set
# CONFIG_SOUND_SSCAPE is not set
CONFIG_SOUND_VMIDI=m
# CONFIG_SOUND_TRIX is not set
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
# CONFIG_SOUND_PAS is not set
# CONFIG_SOUND_PSS is not set
CONFIG_SOUND_SB=m
# CONFIG_SOUND_YM3812 is not set
CONFIG_SOUND_UART6850=m
# CONFIG_SOUND_AEDSP16 is not set
# CONFIG_SOUND_KAHLUA is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_HID_DEBUG is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
CONFIG_USB_PERSIST=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_U132_HCD is not set
CONFIG_USB_SL811_HCD=m
# CONFIG_USB_R8A66597_HCD is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_STORAGE_KARMA is not set
CONFIG_USB_LIBUSUAL=y

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y

#
# USB port drivers
#

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
# CONFIG_USB_SERIAL_HP4X is not set
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
# CONFIG_USB_SERIAL_DEBUG is not set
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
# CONFIG_USB_BERRY_CHARGE is not set
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
# CONFIG_USB_PHIDGET is not set
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
# CONFIG_USB_APPLEDISPLAY is not set
CONFIG_USB_SISUSBVGA=m
# CONFIG_USB_SISUSBVGA_CON is not set
CONFIG_USB_LD=m
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
CONFIG_USB_TEST=m

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set

#
# MMC/SD Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y

#
# MMC/SD Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
# CONFIG_MMC_WBSD is not set
CONFIG_MMC_TIFM_SD=m
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
CONFIG_RTC_DRV_TEST=m

#
# I2C RTC drivers
#
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_MAX6900=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_PCF8583=m
# CONFIG_RTC_DRV_M41T80 is not set

#
# SPI RTC drivers
#

#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
CONFIG_RTC_DRV_DS1553=m
# CONFIG_RTC_DRV_STK17TA8 is not set
CONFIG_RTC_DRV_DS1742=m
CONFIG_RTC_DRV_M48T86=m
# CONFIG_RTC_DRV_M48T59 is not set
CONFIG_RTC_DRV_V3020=m

#
# on-CPU RTC drivers
#

#
# DMA Engine support
#
CONFIG_DMA_ENGINE=y

#
# DMA Clients
#
CONFIG_NET_DMA=y

#
# DMA Devices
#
CONFIG_INTEL_IOATDMA=m
# CONFIG_VIRTUALIZATION is not set

#
# Userspace I/O
#
CONFIG_UIO=m
# CONFIG_UIO_CIF is not set

#
# File systems
#
CONFIG_EXT2_FS=m
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
CONFIG_NLS_CODEPAGE_863=m
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Distributed Lock Manager
#
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
# CONFIG_INSTRUMENTATION is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set

#
# Page alloc debug is incompatible with Software Suspend on i386
#
# CONFIG_DEBUG_RODATA is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_HASH=m
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_HMAC=m
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_TWOFISH_586=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
# CONFIG_CRYPTO_TEST is not set
# CONFIG_CRYPTO_HW is not set

#
# Library routines
#
CONFIG_BITREVERSE=m
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=m
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 18:14           ` Pavel Machek
@ 2007-11-15 17:31             ` Mark Lord
  2007-11-15 19:34               ` Ingo Molnar
  2007-11-15 20:27               ` Rafael J. Wysocki
  0 siblings, 2 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-15 17:31 UTC (permalink / raw)
  To: Pavel Machek
  Cc: Mark Lord, Thomas Gleixner, len.brown, Andrew Morton,
	linux-kernel, linux-pm, rjw, Ingo Molnar

> Hi!
> 
>> > I have been reporting this off and on since 2.6.23 was released.
>> > This problem was not apparent up to perhaps 2.6.23-rc8,
>> > but definitely became common in 2.6.23 and 2.6.23.1.
>> > 
>> > Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
>> > of kernel time to complete.
>> > 
>> > Once in a while, it takes *much* longer, in the 14-20 second range.
>> > These long events *seem* to be mostly after the notebook has been
>> > in suspend for a longish time, but there's really nothing consistent here.
>> > 
>> > So git-bisect isn't going to work for this one.   I recently rebuilt the 
>> > kernel
>> > to include printk timestamps, and then it went 2 days without the issue 
>> > happening,
>> > until this morning (after an overnight suspend) finally.
>> > 
>> > The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB 
>> > DDR2.
>> > PCIe express chipset, ATI graphics, SATA hard drive.
>> > 
>> > 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
>> > Express Memory Controller Hub (rev 03)
>> > 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
>> > Express PCI Express Root Port (rev 03)
>> > 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
>> > Definition Audio Controller (rev 01)
>> > 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> > 1 (rev 01)
>> > 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> > 2 (rev 01)
>> > 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> > 4 (rev 01)
>> > 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 
>> > (rev 01)
>> > 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 
>> > (rev 01)
>> > 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 
>> > (rev 01)
>> > 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 
>> > (rev 01)
>> > 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
>> > Controller (rev 01)
>> > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
>> > 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface 
>> > Bridge (rev 01)
>> > 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial 
>> > ATA Storage Controller IDE (rev 01)
>> > 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 
>> > 01)
>> > 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility 
>> > X1400
>> > 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX 
>> > (rev 02)
>> > 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
>> > 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 
>> > SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
>> > 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
>> > 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host 
>> > Adapter (rev 0a)
>> > 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
>> > 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network 
>> > Connection (rev 02)
>> > 
>> > There's also a USB2 hub connected, with the Logitech mouse being the
>> > only thing plugged into it at present.
>> > 
>> > The best clue I have of what is happening, other than that it was first
>> > seen during the late 2.6.23-rc* series, are the following two sets of
>> > kernel logs.  The first set is from a "normal" fast wake-up,
>> > and the second set is from the "slow" wake-up seen this morning.
>> > 
>> > Both logs show the same information, in pretty much the same order.
>> > The BIG difference is a bunch of unexplained pauses of exactly 1-second
>> > each that occur during the slow wakeup.
>> > 
>> > The only other difference is that the SATA disk messages are placed
>> > differently within the two logs.  I'm thinking on that one but it
>> > doesn't look significant to me.
>> > 
>> > The real question is, why the 1-sec pauses?
> 
> Can you try nohz=off highres=off? Strange stuff is happening with
> nohz.
..

(added Ingo to CC: list:  maybe this is some weird interaction with CFS
and jiffies being reset to 0 on resume ??)

I can try it, but it won't help debug the problem much.
Remember, this happens very inconsistently, maybe 3-4 times a day,
or not at all for 3-4 days.

But if somebody has a specific bug-fix patch that could explain this,
then I'll happily apply it here.

Cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 16:32         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
  2007-11-15 16:49           ` Ray Lee
@ 2007-11-15 18:14           ` Pavel Machek
  2007-11-15 17:31             ` Mark Lord
  2007-11-18 16:10           ` Mark Lord
  2 siblings, 1 reply; 268+ messages in thread
From: Pavel Machek @ 2007-11-15 18:14 UTC (permalink / raw)
  To: Mark Lord
  Cc: Thomas Gleixner, len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

Hi!

> I have been reporting this off and on since 2.6.23 was released.
> This problem was not apparent up to perhaps 2.6.23-rc8,
> but definitely became common in 2.6.23 and 2.6.23.1.
> 
> Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
> of kernel time to complete.
> 
> Once in a while, it takes *much* longer, in the 14-20 second range.
> These long events *seem* to be mostly after the notebook has been
> in suspend for a longish time, but there's really nothing consistent here.
> 
> So git-bisect isn't going to work for this one.   I recently rebuilt the 
> kernel
> to include printk timestamps, and then it went 2 days without the issue 
> happening,
> until this morning (after an overnight suspend) finally.
> 
> The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB 
> DDR2.
> PCIe express chipset, ATI graphics, SATA hard drive.
> 
> 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
> Express Memory Controller Hub (rev 03)
> 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
> Express PCI Express Root Port (rev 03)
> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
> Definition Audio Controller (rev 01)
> 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> 1 (rev 01)
> 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> 2 (rev 01)
> 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> 4 (rev 01)
> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 
> (rev 01)
> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 
> (rev 01)
> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 
> (rev 01)
> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 
> (rev 01)
> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
> Controller (rev 01)
> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
> 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface 
> Bridge (rev 01)
> 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial 
> ATA Storage Controller IDE (rev 01)
> 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 
> 01)
> 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility 
> X1400
> 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX 
> (rev 02)
> 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
> 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 
> SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
> 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
> 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host 
> Adapter (rev 0a)
> 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
> 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network 
> Connection (rev 02)
> 
> There's also a USB2 hub connected, with the Logitech mouse being the
> only thing plugged into it at present.
> 
> The best clue I have of what is happening, other than that it was first
> seen during the late 2.6.23-rc* series, are the following two sets of
> kernel logs.  The first set is from a "normal" fast wake-up,
> and the second set is from the "slow" wake-up seen this morning.
> 
> Both logs show the same information, in pretty much the same order.
> The BIG difference is a bunch of unexplained pauses of exactly 1-second
> each that occur during the slow wakeup.
> 
> The only other difference is that the SATA disk messages are placed
> differently within the two logs.  I'm thinking on that one but it
> doesn't look significant to me.
> 
> The real question is, why the 1-sec pauses?

Can you try nohz=off highres=off? Strange stuff is happening with
nohz.
									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 17:31             ` Mark Lord
@ 2007-11-15 19:34               ` Ingo Molnar
  2007-11-15 19:36                 ` Ingo Molnar
  2007-11-15 20:27               ` Rafael J. Wysocki
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-15 19:34 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Mark Lord <lkml@rtr.ca> wrote:

>> Can you try nohz=off highres=off? Strange stuff is happening with 
>> nohz.
>
> (added Ingo to CC: list: maybe this is some weird interaction with CFS 
> and jiffies being reset to 0 on resume ??)

hm, CFS should have no impact here. To see what's happening you could 
try to use the latency tracer of the -rt patch and do a cross-resume 
trace.

pick up the latest latency tracer patch from:

  http://redhat.com/~mingo/private/latency-tracer-v2.6.24-rc2-git5-combo.patch

apply it and enable CONFIG_FUNCTION_TRACING, then pick up trace-cmd.c:

  http://redhat.com/~mingo/private/trace-cmd.c

and do something like:

  ./trace-cmd pm-suspend > trace.txt

or:

  ./trace-cmd /bin/bash -c "echo ram > /sys/power/state" > trace.txt

this should trigger suspend - then you should do the resume. If 
everything goes well then trace.txt should contain a pretty large trace 
of all the stuff we do during a suspend+resume.

and wait for such a pause and send us the resulting trace.txt.

if it's an SMP box then first do:

  echo 1 > /proc/sys/kernel/trace_all_cpus

to get a global trace. Let me know if something doesnt work with this 
scheme.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 19:34               ` Ingo Molnar
@ 2007-11-15 19:36                 ` Ingo Molnar
  2007-11-15 22:23                   ` Mark Lord
  2007-11-30 12:56                   ` Jörn Engel
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-15 19:36 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Ingo Molnar <mingo@elte.hu> wrote:

> pick up the latest latency tracer patch from:

sorry, wrong URLs, the correct links are:

   http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
   http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 16:32                                 ` Linus Torvalds
@ 2007-11-15 19:40                                   ` Peter Zijlstra
  2007-11-15 20:44                                     ` Peter Zijlstra
  2007-11-21 23:51                                   ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
  1 sibling, 1 reply; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-15 19:40 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm


On Thu, 2007-11-15 at 08:32 -0800, Linus Torvalds wrote:
> 
> On Thu, 15 Nov 2007, Bron Gondwana wrote:
> > 
> > I guess we'll be doing the one-liner kernel mod and testing
> > that then.
> 
> The thing to look at is "get_dirty_limits()" in mm/page-writeback.c, and 
> in this particular case it's the
> 
> 	unsigned long available_memory = determine_dirtyable_memory();
> 
> that's going to bite you. In particular, note the
> 
> 	x -= highmem_dirtyable_memory(x);
> 
> that we do in determine_dirtyable_memory().
> 
> So in this case, if you basically remove that line, it will allow all of 
> memory to be dirtied (including highmem), and then the background_ratio 
> will work on the whole 6GB.
> 
> HOWEVER! It's worth noting that we also have some other old legacy cruft 
> there that may interfere with your code. In particular, if you look at the 
> top of "get_dirty_limits()", it *also* does a
> 
>         unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
>                                 global_page_state(NR_ANON_PAGES)) * 100) /
>                                         available_memory;
> 
>         dirty_ratio = vm_dirty_ratio;
>         if (dirty_ratio > unmapped_ratio / 2)
>                 dirty_ratio = unmapped_ratio / 2;
> 
> and that whole "unmapped_ratio" comparison is probably bogus these days, 
> since we now take the mapped dirty pages into account. That code harks 
> back to the days before we did that, and dirty ratios only affected 
> non-mapped pages.
> 
> And in particular, now that I look at it, I wonder if it can even go 
> negative (because "available_memory" may be *smaller* than the 
> NR_FILE_MAPPED|ANON_PAGES sum!).
> 
> We'll fix up a negative value anyway (because of the clamping of 
> dirty_ratio to no less than 5), but the point is that the whole 
> "unmapped_ratio" thing probably doesn't make sense any more, and may well 
> make the dirty_ratio not work for you, because you may have a very small 
> unmapped_ratio that effectively makes all dirty limits always clamp to a 
> very small value.
> 
> So regardless, I think you may want to try the appended patch *first*.
> 
> If this patch makes a difference, please holler. I think it's the correct 
> thing to do, but I'm not going to actually commit it without somebody 
> saying that it makes a difference (and preferably Peter Zijlstra and 
> Andrew acking it too).
> 
> Only *after* testing this change is it probably a good idea to test the 
> real hack of then removing the highmem_dirtyable_memory() thing. 
> 
> Peter? Andrew?

I wondered about that part the other day when I went through the BDI
dirty code due to that iozone thing..

The initial commit states:

commit d90e4590519d196004efbb308d0d47596ee4befe
Author: akpm <akpm>
Date:   Sun Oct 13 16:33:20 2002 +0000

    [PATCH] reduce the dirty threshold when there's a lot of mapped

    Dirty memory thresholds are currently set by /proc/sys/vm/dirty_ratio.

    Background writeout levels are controlled by
    /proc/sys/vm/dirty_background_ratio.

    Problem is that these levels are hard to get right - they are too
    static.  If there is a lot of mapped memory around then the 40%
    clamping level causes too much dirty data.  We do lots of scanning in
    page reclaim, and the VM generally starts getting into distress.  Extra
    swapping, extra page unmapping.

    It would be much better to simply tell the caller of write(2) to slow
    down - to write out their dirty data sooner, to make those written
    pages trivially reclaimable.  Penalise the offender, not the innocent
    page allocators.

    This patch changes the writer throttling code so that we clamp down
    much harder on writers if there is a lot of mapped memory in the
    machine.  We only permit memory dirtiers to dirty up to 50% of unmapped
    memory before forcing them to clean their own pagecache.

    BKrev: 3da9a050Mz7H6VkAR9xo6ongavTMrw

But because dirty mapped pages are no longer special, I'd say the reason
for its existance is gone. So,

Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>

As for the highmem part, that was due to buffer cache, and unfortunately
that is still true. Although maybe we can do something smart with the
per-bdi stuff.

> ---
>  mm/page-writeback.c |    8 --------
>  1 files changed, 0 insertions(+), 8 deletions(-)
> 
> diff --git a/mm/page-writeback.c b/mm/page-writeback.c
> index 81a91e6..d55cfca 100644
> --- a/mm/page-writeback.c
> +++ b/mm/page-writeback.c
> @@ -297,20 +297,12 @@ get_dirty_limits(long *pbackground, long *pdirty, long *pbdi_dirty,
>  {
>  	int background_ratio;		/* Percentages */
>  	int dirty_ratio;
> -	int unmapped_ratio;
>  	long background;
>  	long dirty;
>  	unsigned long available_memory = determine_dirtyable_memory();
>  	struct task_struct *tsk;
>  
> -	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
> -				global_page_state(NR_ANON_PAGES)) * 100) /
> -					available_memory;
> -
>  	dirty_ratio = vm_dirty_ratio;
> -	if (dirty_ratio > unmapped_ratio / 2)
> -		dirty_ratio = unmapped_ratio / 2;
> -
>  	if (dirty_ratio < 5)
>  		dirty_ratio = 5;
>  


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-13 22:34           ` Russell King
@ 2007-11-15 20:16             ` Ben Dooks
  0 siblings, 0 replies; 268+ messages in thread
From: Ben Dooks @ 2007-11-15 20:16 UTC (permalink / raw)
  To: Alan Cox, Thomas Gleixner, Mark Lord, alsa-devel, netdev,
	linux-pcmcia, linux-kernel, Natalie Protasevich, linux-ide,
	bugme-daemon, linux-input, Andrew Morton

On Tue, Nov 13, 2007 at 10:34:37PM +0000, Russell King wrote:
> On Tue, Nov 13, 2007 at 06:25:16PM +0000, Alan Cox wrote:
> > > Given the wide range of ARM platforms today, it is utterly idiotic to
> > > expect a single person to be able to provide responses for all ARM bugs.
> > > I for one wish I'd never *VOLUNTEERED* to be a part of the kernel
> > > bugzilla, and really *WISH* I could pull out of that function.
> > 
> > You can. Perhaps that bugzilla needs to point to some kind of
> > arm-maintainers@vger.kernel.org list for the various ARM platform
> > maintainers ?
> 
> That might work - though it would be hard to get all the platform
> maintainers to be signed up to yet another mailing list, I'm sure
> sufficient would do.

As long as it would just be bug reports, I'm sure that most of us
could be persuaded to subscribe. Adding another list for general
discussions is probably not going to be read, the current list
provides more than enough to keep us busy.

-- 
Ben

Q:      What's a light-year?
A:      One-third less calories than a regular year.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 17:31             ` Mark Lord
  2007-11-15 19:34               ` Ingo Molnar
@ 2007-11-15 20:27               ` Rafael J. Wysocki
  1 sibling, 0 replies; 268+ messages in thread
From: Rafael J. Wysocki @ 2007-11-15 20:27 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, Ingo Molnar

On Thursday, 15 of November 2007, Mark Lord wrote:
> > Hi!
> > 
> >> > I have been reporting this off and on since 2.6.23 was released.
> >> > This problem was not apparent up to perhaps 2.6.23-rc8,
> >> > but definitely became common in 2.6.23 and 2.6.23.1.
> >> > 
> >> > Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
> >> > of kernel time to complete.
> >> > 
> >> > Once in a while, it takes *much* longer, in the 14-20 second range.
> >> > These long events *seem* to be mostly after the notebook has been
> >> > in suspend for a longish time, but there's really nothing consistent here.
> >> > 
> >> > So git-bisect isn't going to work for this one.   I recently rebuilt the 
> >> > kernel
> >> > to include printk timestamps, and then it went 2 days without the issue 
> >> > happening,
> >> > until this morning (after an overnight suspend) finally.
> >> > 
> >> > The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ w/3GB 
> >> > DDR2.
> >> > PCIe express chipset, ATI graphics, SATA hard drive.
> >> > 
> >> > 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
> >> > Express Memory Controller Hub (rev 03)
> >> > 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT 
> >> > Express PCI Express Root Port (rev 03)
> >> > 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
> >> > Definition Audio Controller (rev 01)
> >> > 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> >> > 1 (rev 01)
> >> > 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> >> > 2 (rev 01)
> >> > 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
> >> > 4 (rev 01)
> >> > 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 
> >> > (rev 01)
> >> > 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 
> >> > (rev 01)
> >> > 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 
> >> > (rev 01)
> >> > 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 
> >> > (rev 01)
> >> > 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
> >> > Controller (rev 01)
> >> > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
> >> > 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface 
> >> > Bridge (rev 01)
> >> > 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial 
> >> > ATA Storage Controller IDE (rev 01)
> >> > 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 
> >> > 01)
> >> > 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility 
> >> > X1400
> >> > 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX 
> >> > (rev 02)
> >> > 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
> >> > 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 
> >> > SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
> >> > 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
> >> > 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host 
> >> > Adapter (rev 0a)
> >> > 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
> >> > 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network 
> >> > Connection (rev 02)
> >> > 
> >> > There's also a USB2 hub connected, with the Logitech mouse being the
> >> > only thing plugged into it at present.
> >> > 
> >> > The best clue I have of what is happening, other than that it was first
> >> > seen during the late 2.6.23-rc* series, are the following two sets of
> >> > kernel logs.  The first set is from a "normal" fast wake-up,
> >> > and the second set is from the "slow" wake-up seen this morning.
> >> > 
> >> > Both logs show the same information, in pretty much the same order.
> >> > The BIG difference is a bunch of unexplained pauses of exactly 1-second
> >> > each that occur during the slow wakeup.
> >> > 
> >> > The only other difference is that the SATA disk messages are placed
> >> > differently within the two logs.  I'm thinking on that one but it
> >> > doesn't look significant to me.
> >> > 
> >> > The real question is, why the 1-sec pauses?
> > 
> > Can you try nohz=off highres=off? Strange stuff is happening with
> > nohz.
> ..
> 
> (added Ingo to CC: list:  maybe this is some weird interaction with CFS
> and jiffies being reset to 0 on resume ??)
> 
> I can try it, but it won't help debug the problem much.

Well, if you could verify that it doesn't happen at all with NO_HZ unset, that
would be a valuable data point, IMO.

> Remember, this happens very inconsistently, maybe 3-4 times a day,
> or not at all for 3-4 days.
> 
> But if somebody has a specific bug-fix patch that could explain this,
> then I'll happily apply it here.

I'm not aware of any fix related to the symptoms that you observe.

Greetings,
Rafael

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 19:40                                   ` Peter Zijlstra
@ 2007-11-15 20:44                                     ` Peter Zijlstra
  2007-11-15 20:56                                       ` Linus Torvalds
  0 siblings, 1 reply; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-15 20:44 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm


On Thu, 2007-11-15 at 20:40 +0100, Peter Zijlstra wrote:

> As for the highmem part, that was due to buffer cache, and unfortunately
> that is still true. Although maybe we can do something smart with the
> per-bdi stuff.

Something like this ought to do I guess. Although my
mapping_is_buffercache() is the ugliest thing. I'm sure that can be done
better.

Uncompiled, untested

Not-Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
---
 mm/page-writeback.c |   28 ++++++++++++++++++++--------
 1 file changed, 20 insertions(+), 8 deletions(-)

Index: linux-2.6/mm/page-writeback.c
===================================================================
--- linux-2.6.orig/mm/page-writeback.c
+++ linux-2.6/mm/page-writeback.c
@@ -280,27 +280,28 @@ static unsigned long highmem_dirtyable_m
 #endif
 }
 
-static unsigned long determine_dirtyable_memory(void)
+static unsigned long determine_dirtyable_memory(int highmem)
 {
 	unsigned long x;
 
 	x = global_page_state(NR_FREE_PAGES)
 		+ global_page_state(NR_INACTIVE)
 		+ global_page_state(NR_ACTIVE);
-	x -= highmem_dirtyable_memory(x);
+	if (!highmem)
+		x -= highmem_dirtyable_memory(x);
 	return x + 1;	/* Ensure that we never return 0 */
 }
 
 static void
 get_dirty_limits(long *pbackground, long *pdirty, long *pbdi_dirty,
-		 struct backing_dev_info *bdi)
+		 struct backing_dev_info *bdi, int highmem)
 {
 	int background_ratio;		/* Percentages */
 	int dirty_ratio;
 	int unmapped_ratio;
 	long background;
 	long dirty;
-	unsigned long available_memory = determine_dirtyable_memory();
+	unsigned long available_memory = determine_dirtyable_memory(highmem);
 	struct task_struct *tsk;
 
 	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
@@ -346,6 +347,16 @@ get_dirty_limits(long *pbackground, long
 	}
 }
 
+static inline int mapping_is_buffercache(struct address_space *mapping)
+{
+	struct super_block *sb = mapping->host->i_sb;
+
+	if (sb && sb->s_bdev && sb->s_bdev->bd_inode->i_mapping != mapping)
+		return 0;
+
+	return 1;
+}
+
 /*
  * balance_dirty_pages() must be called by processes which are generating dirty
  * data.  It looks at the number of dirty pages in the machine and will force
@@ -364,6 +375,7 @@ static void balance_dirty_pages(struct a
 	unsigned long write_chunk = sync_writeback_pages();
 
 	struct backing_dev_info *bdi = mapping->backing_dev_info;
+	int highmem = !mapping_is_buffercache(mapping);
 
 	for (;;) {
 		struct writeback_control wbc = {
@@ -375,7 +387,7 @@ static void balance_dirty_pages(struct a
 		};
 
 		get_dirty_limits(&background_thresh, &dirty_thresh,
-				&bdi_thresh, bdi);
+				&bdi_thresh, bdi, highmem);
 		bdi_nr_reclaimable = bdi_stat(bdi, BDI_RECLAIMABLE);
 		bdi_nr_writeback = bdi_stat(bdi, BDI_WRITEBACK);
 		if (bdi_nr_reclaimable + bdi_nr_writeback <= bdi_thresh)
@@ -394,7 +406,7 @@ static void balance_dirty_pages(struct a
 			writeback_inodes(&wbc);
 			pages_written += write_chunk - wbc.nr_to_write;
 			get_dirty_limits(&background_thresh, &dirty_thresh,
-				       &bdi_thresh, bdi);
+				       &bdi_thresh, bdi, highmem);
 		}
 
 		/*
@@ -503,7 +515,7 @@ void throttle_vm_writeout(gfp_t gfp_mask
 	long dirty_thresh;
 
         for ( ; ; ) {
-		get_dirty_limits(&background_thresh, &dirty_thresh, NULL, NULL);
+		get_dirty_limits(&background_thresh, &dirty_thresh, NULL, NULL, 1);
 
                 /*
                  * Boost the allowable dirty threshold a bit for page
@@ -546,7 +558,7 @@ static void background_writeout(unsigned
 		long background_thresh;
 		long dirty_thresh;
 
-		get_dirty_limits(&background_thresh, &dirty_thresh, NULL, NULL);
+		get_dirty_limits(&background_thresh, &dirty_thresh, NULL, NULL, 1);
 		if (global_page_state(NR_FILE_DIRTY) +
 			global_page_state(NR_UNSTABLE_NFS) < background_thresh
 				&& min_pages <= 0)




^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 20:44                                     ` Peter Zijlstra
@ 2007-11-15 20:56                                       ` Linus Torvalds
  2007-11-15 20:59                                         ` Peter Zijlstra
  2007-11-15 21:14                                         ` Linus Torvalds
  0 siblings, 2 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 20:56 UTC (permalink / raw)
  To: Peter Zijlstra
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm



On Thu, 15 Nov 2007, Peter Zijlstra wrote:
> 
> Something like this ought to do I guess. Although my
> mapping_is_buffercache() is the ugliest thing. I'm sure that can be done
> better.

No, this absolutely sucks.

Why?

It's totally unacceptable to have per-mapping notions of how much memory 
we have. We used to do *exactly* that, and it's idiocy.

The reason it's unacceptable idiocy is that it means that two processes 
that access different files will then have *TOTALLY*DIFFERENT* notions of 
what the "dirty limit" is. And as a result, one process will happily write 
lots and lots of dirty stuff and never throttle, and the other process 
will have to throttle all the time - and clean up after the process that 
didn't!

See?

The fact is, because we count dirty pages as one resource, we must also 
have *one* limit.

So this patch is a huge regression. You might not notice it, because if 
everybody writes to the same kind of mapping, nobody will be hurt (they 
all have effectively the same global limit anyway), but you *will* notice 
if you ever have two different values of "highmem".

Unacceptable. We used to do exactly what your patch does, and it got fixed 
once. We're not introducing that fundamentally broken concept again.

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 20:56                                       ` Linus Torvalds
@ 2007-11-15 20:59                                         ` Peter Zijlstra
  2007-11-15 21:12                                           ` Peter Zijlstra
  2007-11-15 21:14                                         ` Linus Torvalds
  1 sibling, 1 reply; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-15 20:59 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm


On Thu, 2007-11-15 at 12:56 -0800, Linus Torvalds wrote:
> 
> On Thu, 15 Nov 2007, Peter Zijlstra wrote:
> > 
> > Something like this ought to do I guess. Although my
> > mapping_is_buffercache() is the ugliest thing. I'm sure that can be done
> > better.
> 
> No, this absolutely sucks.

Agreed, I was just about to send out an email saying that..


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 20:59                                         ` Peter Zijlstra
@ 2007-11-15 21:12                                           ` Peter Zijlstra
  0 siblings, 0 replies; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-15 21:12 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm


On Thu, 2007-11-15 at 21:59 +0100, Peter Zijlstra wrote:
> On Thu, 2007-11-15 at 12:56 -0800, Linus Torvalds wrote:
> > 
> > On Thu, 15 Nov 2007, Peter Zijlstra wrote:
> > > 
> > > Something like this ought to do I guess. Although my
> > > mapping_is_buffercache() is the ugliest thing. I'm sure that can be done
> > > better.
> > 
> > No, this absolutely sucks.
> 
> Agreed, I was just about to send out an email saying that.

Say all buffer cache users were against default_backing_dev_info, and
we'd give default_backing_dev_info less, that should work out, right?

( I'm not yet clear on if buffer cache already uses
default_backing_dev_info or not, bdget() seems to suggest it does )






^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 20:56                                       ` Linus Torvalds
  2007-11-15 20:59                                         ` Peter Zijlstra
@ 2007-11-15 21:14                                         ` Linus Torvalds
  2007-11-15 21:26                                           ` Linus Torvalds
                                                             ` (3 more replies)
  1 sibling, 4 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 21:14 UTC (permalink / raw)
  To: Peter Zijlstra
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm



On Thu, 15 Nov 2007, Linus Torvalds wrote:
> 
> Unacceptable. We used to do exactly what your patch does, and it got fixed 
> once. We're not introducing that fundamentally broken concept again.

Examples of non-broken solutions:
 (a) always use lowmem sizes (what we do now)
 (b) always use total mem sizes (sane but potentially dangerous: but the 
     VM pressure should work! It has serious bounce-buffer issues, though, 
     which is why I think it's crazy even if it's otherwise consistent)
 (c) make all dirty counting be *purely* per-bdi, so that everybody can 
     disagree on what the limits are, but at least they also then use 
     different counters

So it's just the "different writers look at the same dirty counts but then 
interpret it to mean totally different things" that I think is so 
fundamentally bogus. I'm not claiming that what we do now is the only way 
to do things, I just don't think your approach is tenable.

Btw, I actually suspect that while (a) is what we do now, for the specific 
case that Bron has, we could have a /proc/sys/vm option to just enable 
(b). So we don't have to have just one consistent model, we can allow odd 
users (and Bron sounds like one - sorry Bron ;) to just force other, odd, 
but consistent models.

I'd also like to point out that while the "bounce buffer" issue is not so 
much a HIGHMEM issue on its own (it's really about the device DMA limits, 
which are _independent_ of HIGHMEM, of course), the reason HIGHMEM is 
special is that without HIGHMEM the bounce buffers generally work 
perfectly fine.

The problem with HIGHMEM is that it causes various metadata (dentries, 
inodes, page struct tables etc) to eat up memory "prime real estate" under 
the same kind of conditions that also dirty a lot of memory. So the reason 
we disallow HIGHMEM from dirty limits is only *partly* the per-device or 
mapping DMA limits, and to a large degree the fact that non-highmem memory 
is special in general, and it is usually the non-highmem areas that are 
constrained - and need to be protected.

			Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:14                                         ` Linus Torvalds
@ 2007-11-15 21:26                                           ` Linus Torvalds
  2007-11-15 21:26                                           ` Peter Zijlstra
                                                             ` (2 subsequent siblings)
  3 siblings, 0 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 21:26 UTC (permalink / raw)
  To: Peter Zijlstra
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm



On Thu, 15 Nov 2007, Linus Torvalds wrote:
> 
> The problem with HIGHMEM is that it causes various metadata (dentries, 
> inodes, page struct tables etc) to eat up memory "prime real estate" under 
> the same kind of conditions that also dirty a lot of memory. So the reason 
> we disallow HIGHMEM from dirty limits is only *partly* the per-device or 
> mapping DMA limits, and to a large degree the fact that non-highmem memory 
> is special in general, and it is usually the non-highmem areas that are 
> constrained - and need to be protected.

Final note on this (promise): 

I'd really be very interested to hear if the patch I *do* think makes 
sense (ie the removal of the old "unmapped_ratio" logic) actually already 
solves most of Bron's problems.

It may well be that that unmapped_ratio logic effectively undid the system 
configuration changes that Bron has done. It doesn't matter if Bron has

	>From our sysctl.conf:
	# This should help reduce flushing on Cache::FastMmap files
	vm.dirty_background_ratio = 50
	vm.dirty_expire_centisecs = 9000
	vm.dirty_ratio = 80
	vm.dirty_writeback_centisecs = 3000

if it turns out that the "unmapped_ratio" logic turns the 80% back down to 
5%.

It may well be that 80% of the non-highmem memory is plenty good enough! 

Sure, older kernels allowed even more of memory to be dirty (since they 
didn't count dirty mappings at all), but we may have a case where the fact 
that we discount the HIGHMEM stuff isn't the major problem in itself, and 
that the dirty_ratio sysctl should be ok - but just gets screwed over by 
that unmapped_ratio logic.

So Bron, if you can test that patch, I'd love to hear if it matters. It 
may not make any difference (maybe you don't actually trigger the 
unmapped_ratio logic at all), but I think it has the potential for being 
totally broken for you.

People that don't change the dirty_ratio from the default values would 
generally never care, because the default dirty-ratio is *already* so low 
that even if the unmapped_ratio logic triggers, it won't much matter!

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:14                                         ` Linus Torvalds
  2007-11-15 21:26                                           ` Linus Torvalds
@ 2007-11-15 21:26                                           ` Peter Zijlstra
  2007-11-15 21:47                                             ` Linus Torvalds
  2007-11-19  3:54                                           ` Bron Gondwana
  2007-11-22  3:42                                           ` [PATCH 1/1] mm: add dirty_highmem option Bron Gondwana
  3 siblings, 1 reply; 268+ messages in thread
From: Peter Zijlstra @ 2007-11-15 21:26 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm, riel, Anton Altaparmakov


On Thu, 2007-11-15 at 13:14 -0800, Linus Torvalds wrote:
> 
> On Thu, 15 Nov 2007, Linus Torvalds wrote:
> > 
> > Unacceptable. We used to do exactly what your patch does, and it got fixed 
> > once. We're not introducing that fundamentally broken concept again.
> 
> Examples of non-broken solutions:
>  (a) always use lowmem sizes (what we do now)
>  (b) always use total mem sizes (sane but potentially dangerous: but the 
>      VM pressure should work! It has serious bounce-buffer issues, though, 
>      which is why I think it's crazy even if it's otherwise consistent)
>  (c) make all dirty counting be *purely* per-bdi, so that everybody can 
>      disagree on what the limits are, but at least they also then use 
>      different counters

I think that (c) is doable. If its worth the effort, who knows,
apparently there still are people using 32bit kernels on boxen with
mucho memory.

> So it's just the "different writers look at the same dirty counts but then 
> interpret it to mean totally different things" that I think is so 
> fundamentally bogus. I'm not claiming that what we do now is the only way 
> to do things, I just don't think your approach is tenable.

Agreed, the per mapping thing was utter crap.

> I'd also like to point out that while the "bounce buffer" issue is not so 
> much a HIGHMEM issue on its own (it's really about the device DMA limits, 
> which are _independent_ of HIGHMEM, of course), the reason HIGHMEM is 
> special is that without HIGHMEM the bounce buffers generally work 
> perfectly fine.
> 
> The problem with HIGHMEM is that it causes various metadata (dentries, 
> inodes, page struct tables etc) to eat up memory "prime real estate" under 
> the same kind of conditions that also dirty a lot of memory. So the reason 
> we disallow HIGHMEM from dirty limits is only *partly* the per-device or 
> mapping DMA limits, and to a large degree the fact that non-highmem memory 
> is special in general, and it is usually the non-highmem areas that are 
> constrained - and need to be protected.

But this problem is already an issue, Anton recently had a case where a
12GB highmem box locked up due to NTFS running out of lowmem - or
something like that.

And I think that with the targeted slab reclaim (or slab defrag as its
apparently still called) we can properly fix this side of the problem. I
think Rik was looking into doing so.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:26                                           ` Peter Zijlstra
@ 2007-11-15 21:47                                             ` Linus Torvalds
  2007-11-15 22:11                                               ` Chris Friesen
                                                                 ` (3 more replies)
  0 siblings, 4 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 21:47 UTC (permalink / raw)
  To: Peter Zijlstra
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm, riel, Anton Altaparmakov



On Thu, 15 Nov 2007, Peter Zijlstra wrote:
> 
> But this problem is already an issue, Anton recently had a case where a
> 12GB highmem box locked up due to NTFS running out of lowmem - or
> something like that.

Yeah. I always considered HIGHMEM to just be unusable. It's ok for 
extending to 2-4GB (ie HIGHMEM4G, not 64G), and it's probably borderline 
usable for 4-8G if you are careful.

But quite frankly, I refuse to even care about anything past that. If you 
have 12G (or heaven forbid, even more) in your machine, and you can't be 
bothered to just upgrade to a 64-bit CPU, then quite frankly, *I* 
personally can't be bothered to care.

That's my personal opinion, and I realize that some of the commercial 
vendors may care about their insane customers' satisfaction, but I'm 
simply not interested in insane users. If they have that much RAM (and 
bought it a few years ago when a 64-bit CPU wasn't an option), they can't 
be poor.

So the _only_ explanation today for 12GB on a 32-bit machine is
 (a) insanity
or 
 (b) being so lazy as to not bother to upgrade
and in either case, my personal reaction is "I'm *not* crazy, and yes, I'm 
lazy too, and I can't give a rats *ss about those problems".

HIGHMEM was a mistake in the first place. It's one that we can live with, 
but I refuse to support it more than it needs to be supported. And 12GB is 
*way* past the end of what is worth supporting.

			Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:47                                             ` Linus Torvalds
@ 2007-11-15 22:11                                               ` Chris Friesen
  2007-11-15 22:31                                                 ` Linus Torvalds
  2007-11-15 22:24                                               ` Rob Mueller
                                                                 ` (2 subsequent siblings)
  3 siblings, 1 reply; 268+ messages in thread
From: Chris Friesen @ 2007-11-15 22:11 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Peter Zijlstra, Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm, riel, Anton Altaparmakov

Linus Torvalds wrote:

> So the _only_ explanation today for 12GB on a 32-bit machine is
>  (a) insanity
> or 
>  (b) being so lazy as to not bother to upgrade
> and in either case, my personal reaction is "I'm *not* crazy, and yes, I'm 
> lazy too, and I can't give a rats *ss about those problems".

How about...

c) they bought it at the beginning of a project and are stuck with it 
because they aren't getting any more money for hardware

d) they've shipped it to the field and have to support it

We've got some 32-bit 8GB boxes for which both of these would hold true.

Chris

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 19:36                 ` Ingo Molnar
@ 2007-11-15 22:23                   ` Mark Lord
  2007-11-16  5:55                     ` Ingo Molnar
                                       ` (2 more replies)
  2007-11-30 12:56                   ` Jörn Engel
  1 sibling, 3 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-15 22:23 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw

Ingo Molnar wrote:
> * Ingo Molnar <mingo@elte.hu> wrote:
> 
>> pick up the latest latency tracer patch from:
> 
> sorry, wrong URLs, the correct links are:
> 
>    http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
>    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
..

Is there a version of these that works with 2.6.23.1 ?

I'm not using 2.6.24-* on this machine because:
  (a) behaviour may be different, and
  (b) something broke VMware compatibility again.

Thanks

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:47                                             ` Linus Torvalds
  2007-11-15 22:11                                               ` Chris Friesen
@ 2007-11-15 22:24                                               ` Rob Mueller
  2007-11-18 23:13                                                 ` Daniel Phillips
  2007-11-16  0:48                                               ` Alan Cox
  2007-11-21 21:25                                               ` Jan Engelhardt
  3 siblings, 1 reply; 268+ messages in thread
From: Rob Mueller @ 2007-11-15 22:24 UTC (permalink / raw)
  To: Linus Torvalds, Peter Zijlstra
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, riel, Anton Altaparmakov


> That's my personal opinion, and I realize that some of the commercial
> vendors may care about their insane customers' satisfaction, but I'm
> simply not interested in insane users. If they have that much RAM (and
> bought it a few years ago when a 64-bit CPU wasn't an option), they can't
> be poor.

>From our perspective, the main issue is that some of these machines we spent 
quite a bit of money on the big RAM (for it's day) + lots of 15k RPM SCSI 
drives + multi-year support contracts. They're highly IO bound, and barely 
use 10-20% of their old 2.4Ghz Prestonia Xeon CPUs. It's hard to justify 
junking those machines < 5 years.

We have a couple of 6G machines and some 8G machines using PAE. On the 
whole, they actually have been working really well (hmmm, apart from the 
recent dirty pages issue + reiserfs data=journal leaks + inodes in lowmem 
limits)

Rob


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 22:11                                               ` Chris Friesen
@ 2007-11-15 22:31                                                 ` Linus Torvalds
  0 siblings, 0 replies; 268+ messages in thread
From: Linus Torvalds @ 2007-11-15 22:31 UTC (permalink / raw)
  To: Chris Friesen
  Cc: Peter Zijlstra, Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm, riel, Anton Altaparmakov



On Thu, 15 Nov 2007, Chris Friesen wrote:
> 
> We've got some 32-bit 8GB boxes for which both of these would hold true.

Still not enough of a reason for me to care.

Remember - I'm the guy who refused to merge RH's 4G:4G patches because I 
thought they were an unsupportable nightmare.

I care a lot about future supportability, and HIGHMEM is there purely as a 
temporary wart and blip on the screen.

I did acknowledge that others may care more, but the fact is, I suspect 
that it's going to be cheaper to literally buy and ship a new machine to a 
customer than to really "suppport" it in any other form.

Side note: HIGHMEM64G works perfectly fine with 12GB of RAM under 
*limited*loads*. If your customer does certain well-defined and simple 
things that don't put huge and varied loads on the VFS or VM layer, then 
12GB+ is probably fine regardless.

			Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15  2:50                     ` Neil Brown
@ 2007-11-16  0:05                       ` J. Bruce Fields
  0 siblings, 0 replies; 268+ messages in thread
From: J. Bruce Fields @ 2007-11-16  0:05 UTC (permalink / raw)
  To: Neil Brown
  Cc: Randy Dunlap, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-input,
	bugme-daemon

On Thu, Nov 15, 2007 at 01:50:43PM +1100, Neil Brown wrote:
> Virtual Folders.
> 
> I use VM mode in EMACS, but I believe some other mail readers have the
> same functionality.
> I have a virtual folder called "nfs" which shows me all mail in my
> inbox which has the string 'nfs' or 'lockd' in a To, Cc, or Subject
> field.  When I visit that folder, I see all mail about nfs, whether it
> was sent to me personally, or to a relevant list, or to lkml.

Hm (googling around for "mutt" and "virtual folders"): looks like I can
get most of the way there in mutt with some macros based on its "limit"
command:

	http://www.tummy.com/journals/entries/jafo_20060303_044440

Thanks.--b.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:47                                             ` Linus Torvalds
  2007-11-15 22:11                                               ` Chris Friesen
  2007-11-15 22:24                                               ` Rob Mueller
@ 2007-11-16  0:48                                               ` Alan Cox
  2007-11-21 21:25                                               ` Jan Engelhardt
  3 siblings, 0 replies; 268+ messages in thread
From: Alan Cox @ 2007-11-16  0:48 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Peter Zijlstra, Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm, riel, Anton Altaparmakov

> So the _only_ explanation today for 12GB on a 32-bit machine is
>  (a) insanity
> or 
>  (b) being so lazy as to not bother to upgrade
> and in either case, my personal reaction is "I'm *not* crazy, and yes, I'm 
> lazy too, and I can't give a rats *ss about those problems".

12GB-16GB worked well historically so its a regression. Above 16GB its
all utterly mad.

You forgot reason (c) though

(c) 32bit is a tested approved certified etc environment - essentially
conservativsm and paranoia, and its hard to explain to some of these
people that the right answer really is less RAM or 64bit, especially as
they may already know it but have a 12 month process to prove and certify
a system configuration.

> HIGHMEM was a mistake in the first place. It's one that we can live with, 
> but I refuse to support it more than it needs to be supported. And 12GB is 
> *way* past the end of what is worth supporting.

Highmem to 4GB was sensible. Highmem to 8GB was pushing it.

Alan

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 22:23                   ` Mark Lord
@ 2007-11-16  5:55                     ` Ingo Molnar
  2007-11-16  7:15                       ` Ingo Molnar
  2007-11-16 18:35                     ` Mark Lord
  2007-11-30 20:12                     ` Mark Lord
  2 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16  5:55 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Mark Lord <lkml@rtr.ca> wrote:

>> sorry, wrong URLs, the correct links are:
>>
>>    http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
>>    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
> ..
>
> Is there a version of these that works with 2.6.23.1 ?

yes, i've backported it and have uploaded the v2.6.23 version to:

  http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.23.1-combo.patch

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16  5:55                     ` Ingo Molnar
@ 2007-11-16  7:15                       ` Ingo Molnar
  2007-11-16  8:21                         ` Ingo Molnar
  2007-11-16 19:06                         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16  7:15 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Ingo Molnar <mingo@elte.hu> wrote:

> > Is there a version of these that works with 2.6.23.1 ?
> 
> yes, i've backported it and have uploaded the v2.6.23 version to:
> 
>   http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.23.1-combo.patch

btw., if the trace is too large and the interesting section of suspend 
does not fit into it then you can narrow it down to the most important 
events only by changing this in trace-cmd.c:

        system("echo 1 > /proc/sys/kernel/mcount_enabled");

to:

        system("echo 0 > /proc/sys/kernel/mcount_enabled");

that way we'll still trace IRQs and scheduling events, which is enough 
to see roughly where the delay is happening. To include symbolic 
backtraces in the trace, do this:

	echo 1 > /proc/sys/kernel/stackframe_tracing

to get such trace entries:

      ls 3688  1D..3 4642us+: deactivate_task <ls 3688> (0 0)
      ls 3688  1D..3 4644us+: schedule()<-do_exit()<-sys_exit_group()<-sys_exit_group()
      ls 3688  1D..3 4647us+: sysenter_past_esp()<-(   -1)()<-(    0)()<-(    0)()
  <idle> 0     1D..2 4652us : schedule <ls 3688> (0 20)

this way we can see why a task goes to sleep and which exact kernel 
codepath is waking it up.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-15 16:19                       ` Daniel Barkalow
@ 2007-11-16  8:20                         ` Romano Giannetti
  2007-11-16 18:20                           ` Daniel Barkalow
  0 siblings, 1 reply; 268+ messages in thread
From: Romano Giannetti @ 2007-11-16  8:20 UTC (permalink / raw)
  To: Daniel Barkalow
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel


(Cc: trimmed a bit).

On Thu, 2007-11-15 at 11:19 -0500, Daniel Barkalow wrote:
> On Thu, 15 Nov 2007, Theodore Tso wrote:
[...]
> > A full kernel build with everything selected can take good 30 minutes or 
> > more, and that's on a fast dual-core machine with 4gigs of memory and 
> > 7200rpm disk drives. On a slower, memory limited laptop, doing a single 
> > kernel build can take more time than the user has patiences; multiply 
> > that by 7 or 8 build and test boots, and it starts to get tiresome.
> 
> None of this is going to take as long, 

Well, the compile phase can. Especially if the first time you try to
compile the kernel with EXTRAVERSION=`git describe` which force almost a
full rebuild every time...

But the worst problem is that a full recompile, with a distro .config,
will take hours on my 2.66GHz/CoreDuo/1G ram. Trimming down .config is
fundamental to be able to bisect effectively, but it's not an easy thing
to do for an unexperienced user (and a painful one for all the rest of
us). 

What would be an invaluable help would be a tool that generates
a .config with all the modules and subsystems I am using *now*. Should
be possible in principle by parsing KConfig and Makefiles and using as
input the current .config and lsmod... is it possible to map the kernel
object name to the option enabling it?

Romano 


-- 
Sorry for the disclaimer --- ¡I cannot stop it!



--
La presente comunicación tiene carácter confidencial y es para el exclusivo uso del destinatario indicado en la misma. Si Ud. no es el destinatario indicado, le informamos que cualquier forma de distribución, reproducción o uso de esta comunicación y/o de la información contenida en la misma están estrictamente prohibidos por la ley. Si Ud. ha recibido esta comunicación por error, por favor, notifíquelo inmediatamente al remitente contestando a este mensaje y proceda a continuación a destruirlo. Gracias por su colaboración.

This communication contains confidential information. It is for the exclusive use of the intended addressee. If you are not the intended addressee, please note that any form of distribution, copying or use of this communication or the information in it is strictly prohibited by law. If you have received this communication in error, please immediately notify the sender by reply e-mail and destroy this message. Thank you for your cooperation. 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16  7:15                       ` Ingo Molnar
@ 2007-11-16  8:21                         ` Ingo Molnar
  2007-11-16 11:23                           ` Ingo Molnar
  2007-11-16 19:06                         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16  8:21 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


ok, i experimented around with the latency tracer, trying to capture the 
trace of a full suspend+resume cycle, and it needed the tracer fix below 
(GTOD clocksource suspend/resume would otherwise confuse the tracer and 
you'd get no trace output as a result).

once that tracer bug was fixed, the best method to generate a trace was 
to do this:

   echo 1 > /proc/sys/kernel/stackframe_tracing
   echo 1 > /proc/sys/kernel/syscall_tracing
   ./trace-cmd bash -c "echo mem > /sys/power/state" > trace.txt

	Ingo

---
 kernel/latency_trace.c |   53 +++++++++++++++++++++++++++++++++----------------
 1 file changed, 36 insertions(+), 17 deletions(-)

Index: linux/kernel/latency_trace.c
===================================================================
--- linux.orig/kernel/latency_trace.c
+++ linux/kernel/latency_trace.c
@@ -67,13 +67,6 @@ static unsigned long notrace cycles_to_u
 }
 #endif
 
-static notrace inline cycle_t now(void)
-{
-	if (trace_use_raw_cycles)
-		return get_cycles();
-	return get_monotonic_cycles();
-}
-
 #ifndef irqs_off
 # define irqs_off()			0
 #endif
@@ -237,6 +230,8 @@ struct cpu_trace {
 	unsigned long critical_sequence;
 	atomic_t underrun;
 	atomic_t overrun;
+	cycle_t cycles;
+	cycle_t last_cycles;
 	int early_warning;
 	int latency_type;
 	int cpu;
@@ -263,6 +258,30 @@ static struct cpu_trace cpu_traces[NR_CP
 #endif
  } };
 
+static notrace cycle_t now(struct cpu_trace *tr, int monotonic)
+{
+	cycles_t now, delta, last = tr->last_cycles;
+
+	if (trace_use_raw_cycles && !monotonic)
+		now = get_cycles();
+	else
+		now = get_monotonic_cycles();
+
+	/*
+	 * Protect against time warps:
+	 */
+	if (unlikely(now < last))
+		delta = 1;
+	else
+		delta = now - last;
+
+	tr->last_cycles = now;
+	tr->cycles += delta;
+
+	return tr->cycles;
+}
+
+
 #ifdef CONFIG_EVENT_TRACE
 
 int trace_enabled = 0;
@@ -615,7 +634,7 @@ ____trace(int cpu, enum trace_type type,
 again:
 	idx = tr->trace_idx;
 	idx_next = idx + 1;
-	timestamp = now();
+	timestamp = now(tr, 0);
 
 	if (unlikely((trace_freerunning || print_functions || atomic_read(&tr->underrun)) &&
 		     (idx_next >= MAX_TRACE) && !atomic_read(&tr->overrun))) {
@@ -1743,7 +1762,7 @@ check_critical_timing(int cpu, struct cp
 	 * as long as possible:
 	 */
 	T0 = tr->preempt_timestamp;
-	T1 = get_monotonic_cycles();
+	T1 = now(tr, 1);
 	delta = T1-T0;
 
 	local_save_flags(flags);
@@ -1757,7 +1776,7 @@ check_critical_timing(int cpu, struct cp
 	 * might change it (it can only get larger so the latency
 	 * is fair to be reported):
 	 */
-	T2 = get_monotonic_cycles();
+	T2 = now(tr, 1);
 
 	delta = T2-T0;
 
@@ -1807,7 +1826,7 @@ check_critical_timing(int cpu, struct cp
 	printk(" =>   ended at timestamp %lu: ", t1);
 	print_symbol("<%s>\n", tr->critical_end);
 	dump_stack();
-	t1 = cycles_to_usecs(get_monotonic_cycles());
+	t1 = cycles_to_usecs(now(tr, 1));
 	printk(" =>   dump-end timestamp %lu\n\n", t1);
 #endif
 
@@ -1817,7 +1836,7 @@ check_critical_timing(int cpu, struct cp
 
 out:
 	tr->critical_sequence = max_sequence;
-	tr->preempt_timestamp = get_monotonic_cycles();
+	tr->preempt_timestamp = now(tr, 1);
 	tr->early_warning = 0;
 	reset_trace_idx(cpu, tr);
 	_trace_cmdline(cpu, tr);
@@ -1866,7 +1885,7 @@ __start_critical_timing(unsigned long ei
 	atomic_inc(&tr->disabled);
 
 	tr->critical_sequence = max_sequence;
-	tr->preempt_timestamp = get_monotonic_cycles();
+	tr->preempt_timestamp = now(tr, 1);
 	tr->critical_start = eip;
 	reset_trace_idx(cpu, tr);
 	tr->latency_type = latency_type;
@@ -2150,7 +2169,7 @@ check_wakeup_timing(struct cpu_trace *tr
 		goto out;
 
 	T0 = tr->preempt_timestamp;
-	T1 = get_monotonic_cycles();
+	T1 = now(tr, 1);
 	/*
 	 * Any wraparound or time warp and we are out:
 	 */
@@ -2255,7 +2274,7 @@ void __trace_start_sched_wakeup(struct t
 //	if (!atomic_read(&tr->disabled)) {
 		atomic_inc(&tr->disabled);
 		tr->critical_sequence = max_sequence;
-		tr->preempt_timestamp = get_monotonic_cycles();
+		tr->preempt_timestamp = now(tr, 1);
 		tr->latency_type = WAKEUP_LATENCY;
 		tr->critical_start = CALLER_ADDR0;
 		_trace_cmdline(raw_smp_processor_id(), tr);
@@ -2366,7 +2385,7 @@ long user_trace_start(void)
 	reset_trace_idx(cpu, tr);
 
 	tr->critical_sequence = max_sequence;
-	tr->preempt_timestamp = get_monotonic_cycles();
+	tr->preempt_timestamp = now(tr, 1);
 	tr->critical_start = CALLER_ADDR0;
 	_trace_cmdline(cpu, tr);
 	mcount();
@@ -2425,7 +2444,7 @@ long user_trace_stop(void)
 		unsigned long long tmp0;
 
 		T0 = tr->preempt_timestamp;
-		T1 = get_monotonic_cycles();
+		T1 = now(tr, 1);
 		tmp0 = preempt_max_latency;
 		if (T1 < T0)
 			T0 = T1;

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16  8:21                         ` Ingo Molnar
@ 2007-11-16 11:23                           ` Ingo Molnar
  2007-11-16 11:53                             ` Mike Galbraith
  2007-11-16 12:43                             ` Ingo Molnar
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16 11:23 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw, Len Brown


* Ingo Molnar <mingo@elte.hu> wrote:

> once that tracer bug was fixed, the best method to generate a trace 
> was to do this:
> 
>    echo 1 > /proc/sys/kernel/stackframe_tracing
>    echo 1 > /proc/sys/kernel/syscall_tracing
>    ./trace-cmd bash -c "echo mem > /sys/power/state" > trace.txt

so here's an UP suspend+resume trace i did:

  http://redhat.com/~mingo/latency-tracing-patches/misc/trace-suspend-long.txt.bz2

tons of detail - which might be interesting to other folks as well. Fact 
is, our suspend-to-RAM+resume cycle is very, very slow, even on fast 
hardware - and this trace shows all the reasons why.

This was a fully cached system - i.e. i've done a suspend+resume before 
to warm up the caches. (not that suspend+resume does much IO normally.)

The trace shows that a suspend+resume cycle is 7.95 seconds long 
(without counting the time the box spent suspended) - ouch! This was a 
T60 with Core2Duo 1.83GHz.

For example here is where freezing starts:

    bash-2397  0.... 31686us : remove_wait_queue (vt_waitactive)
    bash-2397  0.... 31688us : freeze_processes (enter_state)
    bash-2397  0.... 31689us : printk (freeze_processes)

here is where the ACPI code triggers the suspend:

    bash-2397  0D... 1904138us : acpi_hw_low_level_write (acpi_hw_register_write)

but this is a whopping 1.9 seconds into the trace already!

first sign of life after i opened the laptop lid again:

    bash-2397  0D... 1904138us : __restore_processor_state (restore_processor_state)
    bash-2397  0D... 1904138us : enable_sep_cpu (__restore_processor_state)

(in the trace there's no delay visible - the period of time spent 
suspended is not visible to the tracer.)

One good way to start looking at such traces is to filter out 
rescheduling events alone:

  grep ': schedule <'  trace-suspend-long.txt

that gives a rough outline of what's going on:

   <idle>-0     0D... 1776566us : schedule <bash-2397> (0 20)
     bash-2397  0D... 1786748us : schedule <<idle>-0> (20 0)
 scsi_eh_-419   0D... 1786814us : schedule <bash-2397> (0 -5)
     bash-2397  0D... 1786960us : schedule <scsi_eh_-419> (-5 0)
 scsi_eh_-421   0D... 1787020us : schedule <bash-2397> (0 -5)
     bash-2397  0D... 1787125us : schedule <scsi_eh_-421> (-5 0)

so you can zoom in on the real area of interest by searching for the 
timestamp.

Hope this helps,

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16 11:23                           ` Ingo Molnar
@ 2007-11-16 11:53                             ` Mike Galbraith
  2007-11-16 12:43                             ` Ingo Molnar
  1 sibling, 0 replies; 268+ messages in thread
From: Mike Galbraith @ 2007-11-16 11:53 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw, Len Brown

On Fri, 2007-11-16 at 12:23 +0100, Ingo Molnar wrote:
> * Ingo Molnar <mingo@elte.hu> wrote:
> 
> > once that tracer bug was fixed, the best method to generate a trace 
> > was to do this:
> > 
> >    echo 1 > /proc/sys/kernel/stackframe_tracing
> >    echo 1 > /proc/sys/kernel/syscall_tracing
> >    ./trace-cmd bash -c "echo mem > /sys/power/state" > trace.txt
> 
> so here's an UP suspend+resume trace i did:
> 
>   http://redhat.com/~mingo/latency-tracing-patches/misc/trace-suspend-long.txt.bz2
> 
> tons of detail - which might be interesting to other folks as well. Fact 
> is, our suspend-to-RAM+resume cycle is very, very slow, even on fast 
> hardware - and this trace shows all the reasons why.
> 
> This was a fully cached system - i.e. i've done a suspend+resume before 
> to warm up the caches. (not that suspend+resume does much IO normally.)
> 
> The trace shows that a suspend+resume cycle is 7.95 seconds long 
> (without counting the time the box spent suspended) - ouch! This was a 
> T60 with Core2Duo 1.83GHz.

Ouch?  That's an order of magnitude faster than my 3GHz P4 :)

	-Mike


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16 11:23                           ` Ingo Molnar
  2007-11-16 11:53                             ` Mike Galbraith
@ 2007-11-16 12:43                             ` Ingo Molnar
  2007-11-16 12:58                               ` [patch] snd hda suspend latency: shorten codec read Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16 12:43 UTC (permalink / raw)
  To: Mark Lord
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw, Len Brown


* Ingo Molnar <mingo@elte.hu> wrote:

> so here's an UP suspend+resume trace i did:
> 
>   http://redhat.com/~mingo/latency-tracing-patches/misc/trace-suspend-long.txt.bz2
> 
> tons of detail - which might be interesting to other folks as well. 
> Fact is, our suspend-to-RAM+resume cycle is very, very slow, even on 
> fast hardware - and this trace shows all the reasons why.
> 
> This was a fully cached system - i.e. i've done a suspend+resume 
> before to warm up the caches. (not that suspend+resume does much IO 
> normally.)
> 
> The trace shows that a suspend+resume cycle is 7.95 seconds long 
> (without counting the time the box spent suspended) - ouch! This was a 
> T60 with Core2Duo 1.83GHz.

and the amount of time spent executing on the CPU was only 70 msecs! So 
we spent 99% of that 7.9 seconds with just waiting around. Here are the 
top 10 sleep reasons:

    864  schedule()<-schedule_timeout()<-ps2_sendbyte()<-ps2_command()
    183  schedule()<-vt_waitactive()<-vt_ioctl()<-tty_ioctl()
    164  schedule()<-schedule_timeout()<-acpi_ec_wait()<-acpi_ec_transaction()
    157  schedule()<-refrigerator()<-get_signal_to_deliver()<-do_notify_resume()    
    118  schedule()<-worker_thread()<-kthread()<-kernel_thread_helper()
     80  schedule()<-do_msleep()<-msleep()<-sata_link_debounce()
     64  schedule()<-schedule_timeout()<-inet_csk_accept()<-inet_accept()
     37  schedule()<-__mutex_lock_slowpath()<-mutex_lock()<-acpi_ec_transaction()
     20  schedule()<-schedule_timeout()<-do_select()<-core_sys_select()
     20  schedule()<-io_schedule()<-sync_buffer()<-__wait_on_bit()

what's weird are all those ps2 related sleeps - they make up for much of 
the delay. This how such a sleep point looks like:

    bash 3500  0D... 8641415us : schedule()<-schedule_timeout()<-ps2_sendbyte()<-ps2_command()
    bash 3500  0D... 8641417us : psmouse_sliced_command()<-synaptics_pt_write()<-ps2_sendbyte()<-ps2_command()

it starts somewhere here:

    bash 3500  0.... 5302376us : serio_reconnect_driver (serio_resume)

and ends:

 kseriod 208   0D... 9182560us : synaptics_query_hardware()<-synaptics_reconnect()<-psmouse_reconnect()<-serio_reconnect_driver()

so this section (serio_resume()) took almost 4 seconds.

the main delay seems to be dpm_resume():

    bash 3500  0.N.. 3061040us : dpm_resume (device_resume)
...
    bash 3500  0.... 9105017us : mutex_unlock (dpm_resume)
    bash 3500  0.... 9105018us : mutex_unlock (device_resume)

6.1 seconds!

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* [patch] snd hda suspend latency: shorten codec read
  2007-11-16 12:43                             ` Ingo Molnar
@ 2007-11-16 12:58                               ` Ingo Molnar
  2007-11-16 13:31                                 ` Rafael J. Wysocki
  2007-11-16 14:21                                 ` Takashi Iwai
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-16 12:58 UTC (permalink / raw)
  To: Mark Lord, perex, Takashi Iwai
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw, Len Brown


snd hda suspend latency goes down a second via the patch below.

	Ingo

------------->
Subject: snd hda suspend latency: shorten codec read
From: Ingo Molnar <mingo@elte.hu>

not sleeping for every codec read/write but doing a short udelay and
a conditional reschedule has cut suspend+resume latency by about 1
second on my T60.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 sound/pci/hda/hda_intel.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

Index: linux/sound/pci/hda/hda_intel.c
===================================================================
--- linux.orig/sound/pci/hda/hda_intel.c
+++ linux/sound/pci/hda/hda_intel.c
@@ -555,7 +555,8 @@ static unsigned int azx_rirb_get_respons
 		}
 		if (!chip->rirb.cmds)
 			return chip->rirb.res; /* the last value */
-		schedule_timeout_uninterruptible(1);
+		udelay(10);
+		cond_resched();
 	} while (time_after_eq(timeout, jiffies));
 
 	if (chip->msi) {

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [patch] snd hda suspend latency: shorten codec read
  2007-11-16 12:58                               ` [patch] snd hda suspend latency: shorten codec read Ingo Molnar
@ 2007-11-16 13:31                                 ` Rafael J. Wysocki
  2007-11-16 14:21                                 ` Takashi Iwai
  1 sibling, 0 replies; 268+ messages in thread
From: Rafael J. Wysocki @ 2007-11-16 13:31 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, perex, Takashi Iwai, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, Len Brown

On Friday, 16 of November 2007, Ingo Molnar wrote:
> 
> snd hda suspend latency goes down a second via the patch below.
> 
> 	Ingo
> 
> ------------->
> Subject: snd hda suspend latency: shorten codec read
> From: Ingo Molnar <mingo@elte.hu>
> 
> not sleeping for every codec read/write but doing a short udelay and
> a conditional reschedule has cut suspend+resume latency by about 1
> second on my T60.
> 
> Signed-off-by: Ingo Molnar <mingo@elte.hu>

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>

> ---
>  sound/pci/hda/hda_intel.c |    3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> Index: linux/sound/pci/hda/hda_intel.c
> ===================================================================
> --- linux.orig/sound/pci/hda/hda_intel.c
> +++ linux/sound/pci/hda/hda_intel.c
> @@ -555,7 +555,8 @@ static unsigned int azx_rirb_get_respons
>  		}
>  		if (!chip->rirb.cmds)
>  			return chip->rirb.res; /* the last value */
> -		schedule_timeout_uninterruptible(1);
> +		udelay(10);
> +		cond_resched();
>  	} while (time_after_eq(timeout, jiffies));
>  
>  	if (chip->msi) {
> 
> 



-- 
"Premature optimization is the root of all evil." - Donald Knuth

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [patch] snd hda suspend latency: shorten codec read
  2007-11-16 12:58                               ` [patch] snd hda suspend latency: shorten codec read Ingo Molnar
  2007-11-16 13:31                                 ` Rafael J. Wysocki
@ 2007-11-16 14:21                                 ` Takashi Iwai
  1 sibling, 0 replies; 268+ messages in thread
From: Takashi Iwai @ 2007-11-16 14:21 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, perex, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw, Len Brown

At Fri, 16 Nov 2007 13:58:24 +0100,
Ingo Molnar wrote:
> 
> 
> snd hda suspend latency goes down a second via the patch below.
> 
> 	Ingo
> 
> ------------->
> Subject: snd hda suspend latency: shorten codec read
> From: Ingo Molnar <mingo@elte.hu>
> 
> not sleeping for every codec read/write but doing a short udelay and
> a conditional reschedule has cut suspend+resume latency by about 1
> second on my T60.
> 
> Signed-off-by: Ingo Molnar <mingo@elte.hu>

Cute, I applied to ALSA tree now.  Thanks!


Takashi

> ---
>  sound/pci/hda/hda_intel.c |    3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> Index: linux/sound/pci/hda/hda_intel.c
> ===================================================================
> --- linux.orig/sound/pci/hda/hda_intel.c
> +++ linux/sound/pci/hda/hda_intel.c
> @@ -555,7 +555,8 @@ static unsigned int azx_rirb_get_respons
>  		}
>  		if (!chip->rirb.cmds)
>  			return chip->rirb.res; /* the last value */
> -		schedule_timeout_uninterruptible(1);
> +		udelay(10);
> +		cond_resched();
>  	} while (time_after_eq(timeout, jiffies));
>  
>  	if (chip->msi) {
> 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-16  8:20                         ` Romano Giannetti
@ 2007-11-16 18:20                           ` Daniel Barkalow
  2007-11-16 19:46                             ` Theodore Tso
  0 siblings, 1 reply; 268+ messages in thread
From: Daniel Barkalow @ 2007-11-16 18:20 UTC (permalink / raw)
  To: Romano Giannetti
  Cc: Theodore Tso, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel

On Fri, 16 Nov 2007, Romano Giannetti wrote:

> 
> (Cc: trimmed a bit).
> 
> On Thu, 2007-11-15 at 11:19 -0500, Daniel Barkalow wrote:
> > On Thu, 15 Nov 2007, Theodore Tso wrote:
> [...]
> > > A full kernel build with everything selected can take good 30 minutes or 
> > > more, and that's on a fast dual-core machine with 4gigs of memory and 
> > > 7200rpm disk drives. On a slower, memory limited laptop, doing a single 
> > > kernel build can take more time than the user has patiences; multiply 
> > > that by 7 or 8 build and test boots, and it starts to get tiresome.
> > 
> > None of this is going to take as long, 
> 
> Well, the compile phase can. Especially if the first time you try to
> compile the kernel with EXTRAVERSION=`git describe` which force almost a
> full rebuild every time...

Compared to getting useful suggestions from a mailing list, especially 
before you've gotten anybody's attention? Hours or overnight isn't 
particularly long, and doesn't take up much of your time if you've got a 
working kernel to use while it's working.

> But the worst problem is that a full recompile, with a distro .config,
> will take hours on my 2.66GHz/CoreDuo/1G ram. Trimming down .config is
> fundamental to be able to bisect effectively, but it's not an easy thing
> to do for an unexperienced user (and a painful one for all the rest of
> us). 
> 
> What would be an invaluable help would be a tool that generates
> a .config with all the modules and subsystems I am using *now*. Should
> be possible in principle by parsing KConfig and Makefiles and using as
> input the current .config and lsmod... is it possible to map the kernel
> object name to the option enabling it?

I don't think there's anything set up for that, aside from the actual 
build system generating it, and I don't know how hard that would be to 
repurpose for generating a configuration.

	-Daniel
*This .sig left intentionally blank*

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 22:23                   ` Mark Lord
  2007-11-16  5:55                     ` Ingo Molnar
@ 2007-11-16 18:35                     ` Mark Lord
  2007-11-30 20:12                     ` Mark Lord
  2 siblings, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-16 18:35 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw

Mark Lord wrote:
> Ingo Molnar wrote:
>> * Ingo Molnar <mingo@elte.hu> wrote:
>>
>>> pick up the latest latency tracer patch from:
>>
>> sorry, wrong URLs, the correct links are:
>>
>>    
>> http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch 
>>
>>    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
..

make trace-cmd
cc -Wall -O2 -s    trace-cmd.c   -o trace-cmd
trace-cmd.c: In function ‘main’:
trace-cmd.c:65: warning: label ‘usage’ defined but not used


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-16  7:15                       ` Ingo Molnar
  2007-11-16  8:21                         ` Ingo Molnar
@ 2007-11-16 19:06                         ` Mark Lord
  1 sibling, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-16 19:06 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw

Ingo Molnar wrote:
> * Ingo Molnar <mingo@elte.hu> wrote:
> 
>>> Is there a version of these that works with 2.6.23.1 ?
>> yes, i've backported it and have uploaded the v2.6.23 version to:
>>
>>   http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.23.1-combo.patch
..

> ok, i experimented around with the latency tracer, trying to capture the 
> trace of a full suspend+resume cycle, and it needed the tracer fix below 
> (GTOD clocksource suspend/resume would otherwise confuse the tracer and 
> you'd get no trace output as a result).
> 
> once that tracer bug was fixed, the best method to generate a trace was 
> to do this:
> 
>    echo 1 > /proc/sys/kernel/stackframe_tracing
>    echo 1 > /proc/sys/kernel/syscall_tracing
>    ./trace-cmd bash -c "echo mem > /sys/power/state" > trace.txt
..

I've applied the tracer for 2.6.23.1 patch, plus the bugfix,
and now I just get blinking-LEDs (black screen of death) on resume.

Cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-16 18:20                           ` Daniel Barkalow
@ 2007-11-16 19:46                             ` Theodore Tso
  2007-11-17 12:20                               ` Adrian Bunk
  0 siblings, 1 reply; 268+ messages in thread
From: Theodore Tso @ 2007-11-16 19:46 UTC (permalink / raw)
  To: Daniel Barkalow
  Cc: Romano Giannetti, Benoit Boissinot, Mark Lord, Ingo Molnar,
	Andrew Morton, David Miller, protasnb, linux-kernel

On Fri, Nov 16, 2007 at 01:20:16PM -0500, Daniel Barkalow wrote:
> Compared to getting useful suggestions from a mailing list, especially 
> before you've gotten anybody's attention? Hours or overnight isn't 
> particularly long, and doesn't take up much of your time if you've got a 
> working kernel to use while it's working.

But a bisect takes around 7 compiles.  And even when it takes only an
hour, that's enough time for you to get started working on something
else, and saving all of your context so you can at that point try
booting into a kernel really is quite annoying.  Hence the suggestion
for a way for users to download commonly used snapshot points for
bisect runs.  Yes, it will require some central infrastructure, but if
it allows for more distributed debugging, this would be a good thing.

   	      	   	       		       	  - Ted

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Use *poof* for linux-omap (Was: [BUG] New Kernel Bugs)
  2007-11-14 10:07                         ` David Miller
  2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
  2007-11-14 19:44                           ` Russell King
@ 2007-11-16 22:16                           ` Tony Lindgren
  2007-11-17  0:45                             ` Use *poof* for linux-omap David Miller
  2 siblings, 1 reply; 268+ messages in thread
From: Tony Lindgren @ 2007-11-16 22:16 UTC (permalink / raw)
  To: David Miller; +Cc: linux-kernel

Hi Dave,

* David Miller <davem@davemloft.net> [071114 02:09]:

<snip>

> 
> In fact, *poof*, there it is, linux-alsa@vger.kernel.org is there and
> available for anyone who wants to use it.

Can you please use your *poof* trick one more time to set up
linux-omap@vger.kernel.org?

We've (as in linux-omap community) would like to move from subscriber
only list at linux-omap-open-source@linux.omap.com to vger as we're
starting to get more patches and comments on LKML. For related
discussion on linux-omap-open-source@linux.omap.com, see [1].

Regards,

Tony

[1] http://linux.omap.com/pipermail/linux-omap-open-source/2007-November/011980.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Use *poof* for linux-omap
  2007-11-16 22:16                           ` Use *poof* for linux-omap (Was: [BUG] New Kernel Bugs) Tony Lindgren
@ 2007-11-17  0:45                             ` David Miller
  2007-11-18 20:01                               ` Tony Lindgren
  0 siblings, 1 reply; 268+ messages in thread
From: David Miller @ 2007-11-17  0:45 UTC (permalink / raw)
  To: tony; +Cc: linux-kernel

From: Tony Lindgren <tony@atomide.com>
Date: Fri, 16 Nov 2007 14:16:11 -0800

> Can you please use your *poof* trick one more time to set up
> linux-omap@vger.kernel.org?

Done, enjoy.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-16 19:46                             ` Theodore Tso
@ 2007-11-17 12:20                               ` Adrian Bunk
  2007-11-18 18:01                                 ` Theodore Tso
  0 siblings, 1 reply; 268+ messages in thread
From: Adrian Bunk @ 2007-11-17 12:20 UTC (permalink / raw)
  To: Theodore Tso, Daniel Barkalow, Romano Giannetti,
	Benoit Boissinot, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel

On Fri, Nov 16, 2007 at 02:46:18PM -0500, Theodore Tso wrote:
> On Fri, Nov 16, 2007 at 01:20:16PM -0500, Daniel Barkalow wrote:
> > Compared to getting useful suggestions from a mailing list, especially 
> > before you've gotten anybody's attention? Hours or overnight isn't 
> > particularly long, and doesn't take up much of your time if you've got a 
> > working kernel to use while it's working.
> 
> But a bisect takes around 7 compiles.
>...

I don't understand that number.

The common case are regressions in -rc1, and a bisection of
at about 7000 commits takes around 13 compiles.

>    	      	   	       		       	  - Ted

cu
Adrian

-- 

       "Is there not promise of rain?" Ling Tan asked suddenly out
        of the darkness. There had been need of rain for many days.
       "Only a promise," Lao Er said.
                                       Pearl S. Buck - Dragon Seed


^ permalink raw reply	[flat|nested] 268+ messages in thread

* size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-13 17:50                 ` Mark Lord
                                     ` (2 preceding siblings ...)
  2007-11-13 18:39                   ` Matthew Wilcox
@ 2007-11-18 12:44                   ` Pavel Machek
  2007-11-18 12:58                     ` Rene Herman
  2007-11-18 14:56                     ` Ingo Molnar
  3 siblings, 2 replies; 268+ messages in thread
From: Pavel Machek @ 2007-11-18 12:44 UTC (permalink / raw)
  To: Mark Lord
  Cc: Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon

On Tue 2007-11-13 12:50:08, Mark Lord wrote:
> Ingo Molnar wrote:
> >
> >for example git-bisect was godsent. I remember that 
> >years ago bisection of a bug was a very laborous task 
> >so that it was only used as a final, last-ditch 
> >approach for really nasty bugs. Today we can 
> >autonomouly bisect build bugs via a simple shell 
> >command around "git-bisect run", without any human 
> >interaction! This freed up testing resources 
> ..
> 
> It's only a godsend for the few people who happen to be 
> kernel developers
> and who happen to already use git.
> 
> It's a 540MByte download over a slow link for everyone 
> else.

Hmmm, clean-cg is 7.7G on my machine, and yes I tried
git-prune-packed. What am I doing wrong?
						Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-18 12:44                   ` size of git repository (was Re: [BUG] New Kernel Bugs) Pavel Machek
@ 2007-11-18 12:58                     ` Rene Herman
  2007-11-18 14:35                       ` James Bottomley
  2007-11-18 14:56                     ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Rene Herman @ 2007-11-18 12:58 UTC (permalink / raw)
  To: Pavel Machek
  Cc: Mark Lord, Ingo Molnar, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

On 18-11-07 13:44, Pavel Machek wrote:

> On Tue 2007-11-13 12:50:08, Mark Lord wrote:

>> It's a 540MByte download over a slow link for everyone 
>> else.
> 
> Hmmm, clean-cg is 7.7G on my machine, and yes I tried
> git-prune-packed. What am I doing wrong?

clean-cg? But failure to run "git repack -a -d" every once in a while?

Rene.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-18 12:58                     ` Rene Herman
@ 2007-11-18 14:35                       ` James Bottomley
  2007-11-18 15:19                         ` Rene Herman
  0 siblings, 1 reply; 268+ messages in thread
From: James Bottomley @ 2007-11-18 14:35 UTC (permalink / raw)
  To: Rene Herman
  Cc: Pavel Machek, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon


On Sun, 2007-11-18 at 13:58 +0100, Rene Herman wrote:
> On 18-11-07 13:44, Pavel Machek wrote:
> 
> > On Tue 2007-11-13 12:50:08, Mark Lord wrote:
> 
> >> It's a 540MByte download over a slow link for everyone 
> >> else.
> > 
> > Hmmm, clean-cg is 7.7G on my machine, and yes I tried
> > git-prune-packed. What am I doing wrong?
> 
> clean-cg? But failure to run "git repack -a -d" every once in a while?

Actually, the best command is 

git gc

which does a repack (into a single pack file rather than an incremenal),
and then removes all the objects now in the pack.  If, like me, you work
on temporary branches which you keep rebasing, you can add a --prune to
gc which will erase all unreferenced objects as it packs (use this one
with care.  I usually never use it but run a git prune -n just to see
what would be removed, and then run git prune separately if it looks
OK).

James



^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-18 12:44                   ` size of git repository (was Re: [BUG] New Kernel Bugs) Pavel Machek
  2007-11-18 12:58                     ` Rene Herman
@ 2007-11-18 14:56                     ` Ingo Molnar
  2007-11-19  4:43                       ` Willy Tarreau
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-18 14:56 UTC (permalink / raw)
  To: Pavel Machek
  Cc: Mark Lord, Andrew Morton, David Miller, protasnb, linux-kernel,
	netdev, alsa-devel, linux-ide, linux-pcmcia, linux-input,
	bugme-daemon


* Pavel Machek <pavel@ucw.cz> wrote:

> On Tue 2007-11-13 12:50:08, Mark Lord wrote:
> > Ingo Molnar wrote:
> > >
> > >for example git-bisect was godsent. I remember that 
> > >years ago bisection of a bug was a very laborous task 
> > >so that it was only used as a final, last-ditch 
> > >approach for really nasty bugs. Today we can 
> > >autonomouly bisect build bugs via a simple shell 
> > >command around "git-bisect run", without any human 
> > >interaction! This freed up testing resources 
> > ..
> > 
> > It's only a godsend for the few people who happen to be 
> > kernel developers
> > and who happen to already use git.
> > 
> > It's a 540MByte download over a slow link for everyone 
> > else.
> 
> Hmmm, clean-cg is 7.7G on my machine, and yes I tried 
> git-prune-packed. What am I doing wrong?

"git-repack -a -d" gives me ~220 MB:

  $ du -s .git
  222064  .git

anyone who can download a 43 MB tar.bz2 tarball for a kernel release 
should be able to afford a _one time_ download size of 250 MB (the size 
of the current kernel.org git repository). If not, burning a CD or DVD 
and carrying it home ought to do the trick. Git is very 
bandwidth-efficient after that point - lots of people behind narrow 
pipes are using it - it's just the initial clone that takes time. And 
given all the history and metadata that the git repository carries (full 
changelogs, annotations, etc.) it's a no-brainer that kernel developers 
should be using it.

(and you can shrink the 250 MB further down by using shallow clones, 
etc.)

yes, some people complained when distros stopped doing floppy installs. 
Some people complained when distros stopped doing CD installs. Yes, i've 
myself done a 250+ MB download over a 56 kbit modem in the past, and 
while it indeed took overnight to finish, it's very much doable. It's 
not really qualitatively different from the 1.5 hours a kernel tar.bz2 
took to download.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-18 14:35                       ` James Bottomley
@ 2007-11-18 15:19                         ` Rene Herman
  0 siblings, 0 replies; 268+ messages in thread
From: Rene Herman @ 2007-11-18 15:19 UTC (permalink / raw)
  To: James Bottomley
  Cc: Pavel Machek, Mark Lord, Ingo Molnar, Andrew Morton,
	David Miller, protasnb, linux-kernel, netdev, alsa-devel,
	linux-ide, linux-pcmcia, linux-input, bugme-daemon

On 18-11-07 15:35, James Bottomley wrote:

>> clean-cg? But failure to run "git repack -a -d" every once in a while?
> 
> Actually, the best command is
> 
> git gc
> 
> which does a repack (into a single pack file rather than an incremenal), 
> and then removes all the objects now in the pack.  If, like me, you work 
> on temporary branches which you keep rebasing, you can add a --prune to 
> gc which will erase all unreferenced objects as it packs (use this one 
> with care.  I usually never use it but run a git prune -n just to see 
> what would be removed, and then run git prune separately if it looks OK).

Thanks for the comment. That managed to indeed shave a few extra bytes off 
my already "repack -a -d" packed repo still.

Rene.


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 16:32         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
  2007-11-15 16:49           ` Ray Lee
  2007-11-15 18:14           ` Pavel Machek
@ 2007-11-18 16:10           ` Mark Lord
  2007-11-18 16:21             ` Ingo Molnar
  2 siblings, 1 reply; 268+ messages in thread
From: Mark Lord @ 2007-11-18 16:10 UTC (permalink / raw)
  To: Mark Lord
  Cc: Thomas Gleixner, len.brown, Andrew Morton, Linux Kernel,
	linux-pm, rjw, Ingo Molnar

Mark Lord wrote:
> I have been reporting this off and on since 2.6.23 was released.
> This problem was not apparent up to perhaps 2.6.23-rc8,
> but definitely became common in 2.6.23 and 2.6.23.1.
> 
> Most of the time, a resume-from-RAM on my notebook takes about 2.1 seconds
> of kernel time to complete.
> 
> Once in a while, it takes *much* longer, in the 14-20 second range.
> These long events *seem* to be mostly after the notebook has been
> in suspend for a longish time, but there's really nothing consistent here.
> 
> So git-bisect isn't going to work for this one.   I recently rebuilt the 
> kernel
> to include printk timestamps, and then it went 2 days without the issue 
> happening,
> until this morning (after an overnight suspend) finally.
> 
> The machine is a Dell Inspiron 9400, Intel chipset + Core2Duo 2.1GHZ 
> w/3GB DDR2.
> PCIe express chipset, ATI graphics, SATA hard drive.
> 
> 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 
> 945GT Express Memory Controller Hub (rev 03)
> 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 
> 945GT Express PCI Express Root Port (rev 03)
> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
> Definition Audio Controller (rev 01)
> 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express 
> Port 1 (rev 01)
> 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express 
> Port 2 (rev 01)
> 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express 
> Port 4 (rev 01)
> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI 
> #1 (rev 01)
> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI 
> #2 (rev 01)
> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI 
> #3 (rev 01)
> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI 
> #4 (rev 01)
> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
> Controller (rev 01)
> 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
> 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface 
> Bridge (rev 01)
> 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) 
> Serial ATA Storage Controller IDE (rev 01)
> 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller 
> (rev 01)
> 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility 
> X1400
> 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX 
> (rev 02)
> 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
> 03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 
> SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
> 03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
> 03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host 
> Adapter (rev 0a)
> 03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
> 0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG 
> Network Connection (rev 02)
> 
> There's also a USB2 hub connected, with the Logitech mouse being the
> only thing plugged into it at present.
> 
> The best clue I have of what is happening, other than that it was first
> seen during the late 2.6.23-rc* series, are the following two sets of
> kernel logs.  The first set is from a "normal" fast wake-up,
> and the second set is from the "slow" wake-up seen this morning.
> 
> Both logs show the same information, in pretty much the same order.
> The BIG difference is a bunch of unexplained pauses of exactly 1-second
> each that occur during the slow wakeup.
> 
> The only other difference is that the SATA disk messages are placed
> differently within the two logs.  I'm thinking on that one but it
> doesn't look significant to me.
> 
> The real question is, why the 1-sec pauses?
> 
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
> 
> HERE IS THE NORMAL RESUME LOG.
> 
> 
> [  820.147914] CPU1 is down
> [    0.355669] Back to C!
> [    0.356120] Enabling non-boot CPUs ...
> [    0.377167] SMP alternatives: switching to SMP code
> [    0.378565] Booting processor 1/1 eip 3000
> [    0.378568] CPU 1 irqstacks, hard=c0375000 soft=c0373000
> [    0.389374] Initializing CPU#1
> [    0.470225] Calibrating delay using timer specific routine.. 4324.85 
> BogoMIPS (lpj=7204571)
> [    0.470235] CPU: After generic identify, caps: bfebfbff 20100000 
> 00000000 00000000 0000e3bd 00000000 00000001 00000000
> [    0.470244] monitor/mwait feature present.
> [    0.470248] CPU: L1 I cache: 32K, L1 D cache: 32K
> [    0.470252] CPU: L2 cache: 4096K
> [    0.470255] CPU: Physical Processor ID: 0
> [    0.470257] CPU: Processor Core ID: 1
> [    0.470260] CPU: After all inits, caps: bfebfbff 20100000 00000000 
> 00003940 0000e3bd 00000000 00000001 00000000
> [    0.471330] CPU1: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz 
> stepping 06
> [    0.471724] CPU1 is up
> [    0.474787] Switched to high resolution mode on CPU 1
> [    0.483415] PM: Writing back config space on device 0000:00:01.0 at 
> offset a (was f, writing 0)
> [    0.483422] PM: Writing back config space on device 0000:00:01.0 at 
> offset 7 (was e0e0, writing 2000e0e0)
> [    0.483428] PM: Writing back config space on device 0000:00:01.0 at 
> offset 3 (was 10000, writing 10010)
> [    0.483869] PCI: Setting latency timer of device 0000:00:01.0 to 64
> [    0.484224] PM: Writing back config space on device 0000:00:1b.0 at 
> offset f (was 100, writing 10b)
> [    0.484244] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 4 (was ffa7c004, writing efffc004)
> [    0.484250] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 3 (was 0, writing 10)
> [    0.484258] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 1 (was 100000, writing 100102)
> [    0.484282] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, 
> low) -> IRQ 20
> [    0.484292] PCI: Setting latency timer of device 0000:00:1b.0 to 64
> [    0.486711] PM: Writing back config space on device 0000:00:1c.0 at 
> offset f (was 100, writing 20100)
> [    0.486725] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 9 (was 10001, writing 1fff1)
> [    0.486731] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 8 (was 0, writing fff0)
> [    0.486738] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 7 (was 0, writing f0)
> [    0.486744] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 6 (was 0, writing b0b00)
> [    0.486753] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 3 (was 810000, writing 810010)
> [    0.486761] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 1 (was 100000, writing 100007)
> [    0.486782] PCI: Setting latency timer of device 0000:00:1c.0 to 64
> [    0.486788] pciehp_resume ENTRY
> [    0.486829] PM: Writing back config space on device 0000:00:1c.1 at 
> offset f (was 200, writing 20200)
> [    0.486841] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 9 (was 10001, writing 1fff1)
> [    0.486848] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 8 (was 0, writing efc0efc0)
> [    0.486854] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 7 (was 20000000, writing 200000f0)
> [    0.486861] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 6 (was 0, writing c0c00)
> [    0.486870] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 3 (was 810000, writing 810010)
> [    0.486877] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 1 (was 100000, writing 100107)
> [    0.486898] PCI: Setting latency timer of device 0000:00:1c.1 to 64
> [    0.486903] pciehp_resume ENTRY
> [    0.488916] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot 
> hot-add
> [    0.488920] pciehp: Cannot add device 0xc:0
> [    0.488949] PM: Writing back config space on device 0000:00:1c.3 at 
> offset f (was 400, writing 20400)
> [    0.488963] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 9 (was 10001, writing e011e001)
> [    0.488969] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 8 (was 0, writing efb0efa0)
> [    0.488976] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 7 (was 0, writing d0d0)
> [    0.488982] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 6 (was 0, writing e0d00)
> [    0.488991] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 3 (was 810000, writing 810010)
> [    0.488998] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 1 (was 100000, writing 100007)
> [    0.489020] PCI: Setting latency timer of device 0000:00:1c.3 to 64
> [    0.489025] pciehp_resume ENTRY
> [    0.489063] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, 
> low) -> IRQ 19
> [    0.489070] PCI: Setting latency timer of device 0000:00:1d.0 to 64
> [    0.489121] usb usb1: root hub lost power or was reset
> [    0.489144] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
> [    0.489149] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, 
> low) -> IRQ 20
> [    0.489157] PCI: Setting latency timer of device 0000:00:1d.1 to 64
> [    0.489164] PM: Writing back config space on device 0000:00:1d.1 at 
> offset f (was 200, writing 20b)
> [    0.489178] PM: Writing back config space on device 0000:00:1d.1 at 
> offset 8 (was 1, writing bf61)
> [    0.489214] usb usb2: root hub lost power or was reset
> [    0.489236] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
> [    0.489240] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, 
> low) -> IRQ 21
> [    0.489248] PCI: Setting latency timer of device 0000:00:1d.2 to 64
> [    0.489255] PM: Writing back config space on device 0000:00:1d.2 at 
> offset f (was 300, writing 309)
> [    0.489269] PM: Writing back config space on device 0000:00:1d.2 at 
> offset 8 (was 1, writing bf41)
> [    0.489307] usb usb3: root hub lost power or was reset
> [    0.489329] PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
> [    0.489333] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, 
> low) -> IRQ 22
> [    0.489341] PCI: Setting latency timer of device 0000:00:1d.3 to 64
> [    0.489348] PM: Writing back config space on device 0000:00:1d.3 at 
> offset f (was 400, writing 407)
> [    0.489363] PM: Writing back config space on device 0000:00:1d.3 at 
> offset 8 (was 1, writing bf21)
> [    0.489400] usb usb4: root hub lost power or was reset
> [    0.489535] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, 
> low) -> IRQ 19
> [    0.489543] PCI: Setting latency timer of device 0000:00:1d.7 to 64
> [    0.489622] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 9 (was 100f1, writing 1fff1)
> [    0.489629] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 8 (was 90, writing ef90ef90)
> [    0.489635] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 7 (was 2280e0f0, writing 228000f0)
> [    0.489648] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 1 (was 100007, writing 100107)
> [    0.489668] PCI: Setting latency timer of device 0000:00:1e.0 to 64
> [    0.489707] PM: Writing back config space on device 0000:00:1f.0 at 
> offset 1 (was 2100007, writing 2100107)
> [    0.489872] PM: Writing back config space on device 0000:00:1f.2 at 
> offset f (was 200, writing 205)
> [    0.489908] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, 
> low) -> IRQ 17
> [    0.489915] PCI: Setting latency timer of device 0000:00:1f.2 to 64
> [    0.489933] PM: Writing back config space on device 0000:00:1f.3 at 
> offset f (was 200, writing 205)
> [    0.489963] PM: Writing back config space on device 0000:00:1f.3 at 
> offset 1 (was 2800001, writing 2800101)
> [    0.489981] PM: Writing back config space on device 0000:01:00.0 at 
> offset f (was 1ff, writing 104)
> [    0.489996] PM: Writing back config space on device 0000:01:00.0 at 
> offset 3 (was 0, writing 10)
> [    0.490053] PM: Writing back config space on device 0000:0c:00.0 at 
> offset f (was 100, writing 105)
> [    0.490119] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 4 (was 0, writing efcff000)
> [    0.490133] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 3 (was 0, writing 10)
> [    0.490152] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 1 (was 100000, writing 100106)
> [    0.490217] PM: Writing back config space on device 0000:03:00.0 at 
> offset f (was 100, writing 105)
> [    0.490236] PM: Writing back config space on device 0000:03:00.0 at 
> offset 4 (was 0, writing ef9fe000)
> [    0.490242] PM: Writing back config space on device 0000:03:00.0 at 
> offset 3 (was 0, writing 4000)
> [    0.490250] PM: Writing back config space on device 0000:03:00.0 at 
> offset 1 (was 100000, writing 100106)
> [    0.490267] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, 
> low) -> IRQ 17
> [    0.492382] PM: Writing back config space on device 0000:03:01.0 at 
> offset f (was 4020100, writing 4020103)
> [    0.492403] PM: Writing back config space on device 0000:03:01.0 at 
> offset 4 (was 0, writing ef9fd800)
> [    0.492410] PM: Writing back config space on device 0000:03:01.0 at 
> offset 3 (was 800000, writing 804000)
> [    0.492417] PM: Writing back config space on device 0000:03:01.0 at 
> offset 1 (was 2100000, writing 2100106)
> [    0.493339] PM: Writing back config space on device 0000:03:01.1 at 
> offset f (was 200, writing 209)
> [    0.493361] PM: Writing back config space on device 0000:03:01.1 at 
> offset 4 (was 0, writing ef9fd400)
> [    0.493368] PM: Writing back config space on device 0000:03:01.1 at 
> offset 3 (was 800000, writing 804000)
> [    0.493376] PM: Writing back config space on device 0000:03:01.1 at 
> offset 1 (was 2100000, writing 2100106)
> [    0.493397] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, 
> low) -> IRQ 23
> [    0.493428] PM: Writing back config space on device 0000:03:01.2 at 
> offset f (was 200, writing 209)
> [    0.493449] PM: Writing back config space on device 0000:03:01.2 at 
> offset 4 (was 0, writing ef9fd500)
> [    0.493459] PM: Writing back config space on device 0000:03:01.2 at 
> offset 1 (was 2100000, writing 2100106)
> [    0.493480] PM: Writing back config space on device 0000:03:01.3 at 
> offset f (was 200, writing 209)
> [    0.493500] PM: Writing back config space on device 0000:03:01.3 at 
> offset 4 (was 0, writing ef9fd600)
> [    0.493509] PM: Writing back config space on device 0000:03:01.3 at 
> offset 1 (was 2100000, writing 2100102)
> [    0.493530] PM: Writing back config space on device 0000:03:01.4 at 
> offset f (was 200, writing 209)
> [    0.493550] PM: Writing back config space on device 0000:03:01.4 at 
> offset 4 (was 0, writing ef9fd700)
> [    0.493559] PM: Writing back config space on device 0000:03:01.4 at 
> offset 1 (was 2100000, writing 2100102)
> [    0.493599] pciehp_resume ENTRY
> [    0.493633] pciehp_resume ENTRY
> [    0.503412] ata2.00: configured for UDMA/33
> [    0.505628] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot 
> hot-add
> [    0.505633] pciehp: Cannot add device 0xc:0
> [    0.505654] pciehp_resume ENTRY
> [    0.505972] sd 0:0:0:0: [sda] Starting disk
> [    0.601233] ata1.00: configured for UDMA/133
> [    0.624888] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors 
> (160042 MB)
> [    0.624910] sd 0:0:0:0: [sda] Write Protect is off
> [    0.624914] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [    0.624943] sd 0:0:0:0: [sda] Write cache: enabled, read cache: 
> enabled, doesn't support DPO or FUA
> [    0.801255] b44: eth0: Link is up at 100 Mbps, full duplex.
> [    0.801260] b44: eth0: Flow control is off for TX and off for RX.
> [    0.834760] Restarting tasks ... <6>usb 5-1: USB disconnect, address 17
> [    0.972042] done.
> [    0.998126] usb 5-1: new high speed USB device using ehci_hcd and 
> address 21
> [    1.121762] usb 5-1: configuration #1 chosen from 1 choice
> [    1.121912] hub 5-1:1.0: USB hub found
> [    1.121994] hub 5-1:1.0: 4 ports detected
> [    1.224647] usb 5-7: USB disconnect, address 18
> [    1.224651] usb 5-7.1: USB disconnect, address 20
> [    1.334249] usb 5-7: new high speed USB device using ehci_hcd and 
> address 22
> [    1.479331] usb 5-7: configuration #1 chosen from 1 choice
> [    1.479760] hub 5-7:1.0: USB hub found
> [    1.480770] hub 5-7:1.0: 4 ports detected
> [    1.782796] usb 5-1.4: new full speed USB device using ehci_hcd and 
> address 23
> [    1.884536] usb 5-1.4: configuration #1 chosen from 1 choice
> [    2.079252] usb 5-7.1: new low speed USB device using ehci_hcd and 
> address 24
> [    2.166603] usb 5-7.1: configuration #1 chosen from 1 choice
> [    2.169524] input: Logitech Optical USB Mouse as /class/input/input11
> [    2.170506] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] 
> on usb-0000:00:1d.7-7.1
> 
> 
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
> 
> HERE IS THE SLOW RESUME LOG.  Note the 1-second pauses..
> 
> 
> [ 3725.539992] CPU1 is down
> [    0.354353] Back to C!
> [    0.354793] Enabling non-boot CPUs ...
> [    0.389097] SMP alternatives: switching to SMP code
> [    0.389884] Booting processor 1/1 eip 3000
> [    0.389886] CPU 1 irqstacks, hard=c0375000 soft=c0373000
> [    0.401516] Initializing CPU#1
> [    0.482207] Calibrating delay using timer specific routine.. 4324.78 
> BogoMIPS (lpj=7204462)
> [    0.482212] CPU: After generic identify, caps: bfebfbff 20100000 
> 00000000 00000000 0000e3bd 00000000 00000001 00000000
> [    0.482217] monitor/mwait feature present.
> [    0.482219] CPU: L1 I cache: 32K, L1 D cache: 32K
> [    0.482221] CPU: L2 cache: 4096K
> [    0.482222] CPU: Physical Processor ID: 0
> [    0.482223] CPU: Processor Core ID: 1
> [    0.482225] CPU: After all inits, caps: bfebfbff 20100000 00000000 
> 00003940 0000e3bd 00000000 00000001 00000000
> [    0.482814] CPU1: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz 
> stepping 06
> [    0.483053] CPU1 is up
> [    0.486165] Switched to high resolution mode on CPU 1
> [    0.490338] PM: Writing back config space on device 0000:00:01.0 at 
> offset a (was f, writing 0)
> [    0.490342] PM: Writing back config space on device 0000:00:01.0 at 
> offset 7 (was e0e0, writing 2000e0e0)
> [    0.490345] PM: Writing back config space on device 0000:00:01.0 at 
> offset 3 (was 10000, writing 10010)
> [    0.490351] PCI: Setting latency timer of device 0000:00:01.0 to 64
> [    0.490605] PM: Writing back config space on device 0000:00:1b.0 at 
> offset f (was 100, writing 10b)
> [    0.490626] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 4 (was ffa7c004, writing efffc004)
> [    0.490632] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 3 (was 0, writing 10)
> [    0.490640] PM: Writing back config space on device 0000:00:1b.0 at 
> offset 1 (was 100000, writing 100102)
> [    0.490665] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, 
> low) -> IRQ 20
> [    0.490674] PCI: Setting latency timer of device 0000:00:1b.0 to 64
> [    1.492418] PM: Writing back config space on device 0000:00:1c.0 at 
> offset f (was 100, writing 20100)
> [    1.492432] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 9 (was 10001, writing 1fff1)
> [    1.492438] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 8 (was 0, writing fff0)
> [    1.492445] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 7 (was 0, writing f0)
> [    1.492451] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 6 (was 0, writing b0b00)
> [    1.492460] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 3 (was 810000, writing 810010)
> [    1.492468] PM: Writing back config space on device 0000:00:1c.0 at 
> offset 1 (was 100000, writing 100007)
> [    1.492490] PCI: Setting latency timer of device 0000:00:1c.0 to 64
> [    1.492496] pciehp_resume ENTRY
> [    1.492539] PM: Writing back config space on device 0000:00:1c.1 at 
> offset f (was 200, writing 20200)
> [    1.492552] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 9 (was 10001, writing 1fff1)
> [    1.492559] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 8 (was 0, writing efc0efc0)
> [    1.492565] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 7 (was 20000000, writing f0)
> [    1.492572] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 6 (was 0, writing c0c00)
> [    1.492581] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 3 (was 810000, writing 810010)
> [    1.492588] PM: Writing back config space on device 0000:00:1c.1 at 
> offset 1 (was 100000, writing 100107)
> [    1.492610] PCI: Setting latency timer of device 0000:00:1c.1 to 64
> [    1.492615] pciehp_resume ENTRY
> [    1.493885] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot 
> hot-add
> [    1.493889] pciehp: Cannot add device 0xc:0
> [    1.493916] PM: Writing back config space on device 0000:00:1c.3 at 
> offset f (was 400, writing 20400)
> [    1.493929] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 9 (was 10001, writing e011e001)
> [    1.493936] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 8 (was 0, writing efb0efa0)
> [    1.493942] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 7 (was 0, writing d0d0)
> [    1.493949] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 6 (was 0, writing e0d00)
> [    1.493958] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 3 (was 810000, writing 810010)
> [    1.493966] PM: Writing back config space on device 0000:00:1c.3 at 
> offset 1 (was 100000, writing 100007)
> [    1.493987] PCI: Setting latency timer of device 0000:00:1c.3 to 64
> [    1.493992] pciehp_resume ENTRY
> [    1.494028] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, 
> low) -> IRQ 19
> [    1.494036] PCI: Setting latency timer of device 0000:00:1d.0 to 64
> [    1.494088] usb usb1: root hub lost power or was reset
> [    1.494110] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
> [    1.494114] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, 
> low) -> IRQ 20
> [    1.494122] PCI: Setting latency timer of device 0000:00:1d.1 to 64
> [    1.494130] PM: Writing back config space on device 0000:00:1d.1 at 
> offset f (was 200, writing 20b)
> [    1.494144] PM: Writing back config space on device 0000:00:1d.1 at 
> offset 8 (was 1, writing bf61)
> [    1.494180] usb usb2: root hub lost power or was reset
> [    1.494202] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
> [    1.494206] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, 
> low) -> IRQ 21
> [    1.494214] PCI: Setting latency timer of device 0000:00:1d.2 to 64
> [    1.494222] PM: Writing back config space on device 0000:00:1d.2 at 
> offset f (was 300, writing 309)
> [    1.494236] PM: Writing back config space on device 0000:00:1d.2 at 
> offset 8 (was 1, writing bf41)
> [    1.494273] usb usb3: root hub lost power or was reset
> [    1.494295] PCI: Enabling device 0000:00:1d.3 (0000 -> 0001)
> [    1.494299] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, 
> low) -> IRQ 22
> [    1.494307] PCI: Setting latency timer of device 0000:00:1d.3 to 64
> [    1.494314] PM: Writing back config space on device 0000:00:1d.3 at 
> offset f (was 400, writing 407)
> [    1.494328] PM: Writing back config space on device 0000:00:1d.3 at 
> offset 8 (was 1, writing bf21)
> [    1.494365] usb usb4: root hub lost power or was reset
> [    1.496460] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, 
> low) -> IRQ 19
> [    1.496468] PCI: Setting latency timer of device 0000:00:1d.7 to 64
> [    1.496534] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 9 (was 100f1, writing 1fff1)
> [    1.496542] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 8 (was 90, writing ef90ef90)
> [    1.496551] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 7 (was 2280e0f0, writing 228000f0)
> [    1.496570] PM: Writing back config space on device 0000:00:1e.0 at 
> offset 1 (was 100007, writing 100107)
> [    1.496590] PCI: Setting latency timer of device 0000:00:1e.0 to 64
> [    1.496629] PM: Writing back config space on device 0000:00:1f.0 at 
> offset 1 (was 2100007, writing 2100107)
> [    1.745307] PM: Writing back config space on device 0000:00:1f.2 at 
> offset f (was 200, writing 205)
> [    1.745344] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, 
> low) -> IRQ 17
> [    1.745351] PCI: Setting latency timer of device 0000:00:1f.2 to 64
> [    1.745369] PM: Writing back config space on device 0000:00:1f.3 at 
> offset f (was 200, writing 205)
> [    1.745406] PM: Writing back config space on device 0000:00:1f.3 at 
> offset 1 (was 2800001, writing 2800101)
> [    1.745430] PM: Writing back config space on device 0000:01:00.0 at 
> offset f (was 1ff, writing 104)
> [    1.745453] PM: Writing back config space on device 0000:01:00.0 at 
> offset 3 (was 0, writing 10)
> [    1.745514] PM: Writing back config space on device 0000:0c:00.0 at 
> offset f (was 100, writing 105)
> [    1.745584] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 4 (was 0, writing efcff000)
> [    1.745600] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 3 (was 0, writing 10)
> [    1.745623] PM: Writing back config space on device 0000:0c:00.0 at 
> offset 1 (was 100000, writing 100106)
> [    1.745709] PM: Writing back config space on device 0000:03:00.0 at 
> offset f (was 100, writing 105)
> [    1.745729] PM: Writing back config space on device 0000:03:00.0 at 
> offset 4 (was 0, writing ef9fe000)
> [    1.745735] PM: Writing back config space on device 0000:03:00.0 at 
> offset 3 (was 0, writing 4000)
> [    1.745743] PM: Writing back config space on device 0000:03:00.0 at 
> offset 1 (was 100000, writing 100106)
> [    1.745765] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, 
> low) -> IRQ 17
> [    2.753018] PM: Writing back config space on device 0000:03:01.0 at 
> offset f (was 4020100, writing 4020103)
> [    2.753038] PM: Writing back config space on device 0000:03:01.0 at 
> offset 4 (was 0, writing ef9fd800)
> [    2.753045] PM: Writing back config space on device 0000:03:01.0 at 
> offset 3 (was 800000, writing 804000)
> [    2.753053] PM: Writing back config space on device 0000:03:01.0 at 
> offset 1 (was 2100000, writing 2100106)
> [    3.756771] ata1.00: configured for UDMA/133
> [    3.756818] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors 
> (160042 MB)
> [    3.756836] sd 0:0:0:0: [sda] Write Protect is off
> [    3.756840] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [    3.756868] sd 0:0:0:0: [sda] Write cache: enabled, read cache: 
> enabled, doesn't support DPO or FUA
> [    4.763813] b44: eth0: Link is up at 100 Mbps, full duplex.
> [    4.763817] b44: eth0: Flow control is off for TX and off for RX.
> [    4.764090] PM: Writing back config space on device 0000:03:01.1 at 
> offset f (was 200, writing 209)
> [    4.764111] PM: Writing back config space on device 0000:03:01.1 at 
> offset 4 (was 0, writing ef9fd400)
> [    4.764118] PM: Writing back config space on device 0000:03:01.1 at 
> offset 3 (was 800000, writing 804000)
> [    4.764126] PM: Writing back config space on device 0000:03:01.1 at 
> offset 1 (was 2100000, writing 2100106)
> [    4.764145] ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, 
> low) -> IRQ 23
> [    4.764171] PM: Writing back config space on device 0000:03:01.2 at 
> offset f (was 200, writing 209)
> [    4.764191] PM: Writing back config space on device 0000:03:01.2 at 
> offset 4 (was 0, writing ef9fd500)
> [    4.764201] PM: Writing back config space on device 0000:03:01.2 at 
> offset 1 (was 2100000, writing 2100106)
> [    4.764222] PM: Writing back config space on device 0000:03:01.3 at 
> offset f (was 200, writing 209)
> [    4.764242] PM: Writing back config space on device 0000:03:01.3 at 
> offset 4 (was 0, writing ef9fd600)
> [    4.764251] PM: Writing back config space on device 0000:03:01.3 at 
> offset 1 (was 2100000, writing 2100102)
> [    4.764273] PM: Writing back config space on device 0000:03:01.4 at 
> offset f (was 200, writing 209)
> [    4.764293] PM: Writing back config space on device 0000:03:01.4 at 
> offset 4 (was 0, writing ef9fd700)
> [    4.764303] PM: Writing back config space on device 0000:03:01.4 at 
> offset 1 (was 2100000, writing 2100102)
> [    4.764340] pciehp_resume ENTRY
> [    4.764369] pciehp_resume ENTRY
> [    5.765432] ata2.00: configured for UDMA/33
> [    5.767529] pciehp: Device 0000:0c:00.0 already exists at c:0, cannot 
> hot-add
> [    5.767532] pciehp: Cannot add device 0xc:0
> [    5.767547] pciehp_resume ENTRY
> [    5.767864] sd 0:0:0:0: [sda] Starting disk
> [    7.750047] Restarting tasks ... done.
> [    7.830571] usb 5-1: USB disconnect, address 21
> [    8.126832] usb 5-1: new high speed USB device using ehci_hcd and 
> address 25
> [   10.230397] usb 5-1: configuration #1 chosen from 1 choice
> [   10.230517] hub 5-1:1.0: USB hub found
> [   10.230545] hub 5-1:1.0: 4 ports detected
> [   10.281481] usb 5-7: USB disconnect, address 22
> [   10.281489] usb 5-7.1: USB disconnect, address 24
> [   10.889785] usb 5-7: new high speed USB device using ehci_hcd and 
> address 26
> [   11.658319] usb 5-7: configuration #1 chosen from 1 choice
> [   11.658631] hub 5-7:1.0: USB hub found
> [   11.658985] hub 5-7:1.0: 4 ports detected
> [   13.190055] usb 5-1.4: new full speed USB device using ehci_hcd and 
> address 27
> [   13.961678] usb 5-1.4: configuration #1 chosen from 1 choice
> [   14.171766] usb 5-7.1: new low speed USB device using ehci_hcd and 
> address 28
> [   14.295838] usb 5-7.1: configuration #1 chosen from 1 choice
> [   14.298596] input: Logitech Optical USB Mouse as /class/input/input12
> [   14.299091] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] 
> on usb-0000:00:1d.7-7.1
..

This is still happening.  I was hoping my PCIe hotplug bug+fix might have
been related, but no it happened just now after that fix.

Since Ingo's latency trace patches lock up the machine on resume,
the next thing I'll try instead is to re-enable CONFIG_IRQBALANCE=y.

I think that I turned that flag off at around the same time as this
problem began, maybe they're related (?).

I did notice that CONFIG_IRQBALANCE=y *is* necessary to keep my myth box
from having 1-second audio dropouts (2.6.23.1) during playback, so maybe
that same 1-second lockout is happening on this box as well (?).

Cheers 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-18 16:10           ` Mark Lord
@ 2007-11-18 16:21             ` Ingo Molnar
  2007-11-18 17:37               ` Mark Lord
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-18 16:21 UTC (permalink / raw)
  To: Mark Lord
  Cc: Mark Lord, Thomas Gleixner, len.brown, Andrew Morton,
	Linux Kernel, linux-pm, rjw


* Mark Lord <lkml@rtr.ca> wrote:

> Since Ingo's latency trace patches lock up the machine on resume, the 
> next thing I'll try instead is to re-enable CONFIG_IRQBALANCE=y.

hm, which patch did you try? Could you check whether all chunks from the 
patch below are applied? (these are the fixed i did when i was doing 
cross-suspend traces - this is not something i've done before, so the 
tracer had to be adjusted)

i suspect if you turn off CONFIG_FUNCTION_TRACING then you wont get any 
hung resume - and the resulting trace would still be pretty useful. (it 
will show scheduling and irq activities, etc.)

	Ingo

---
 arch/x86/kernel/stacktrace.c     |    2 +-
 arch/x86/power/cpu.c             |    3 ++-
 drivers/acpi/namespace/nsutils.c |    2 +-
 drivers/acpi/namespace/nswalk.c  |    2 +-
 include/linux/sched.h            |    2 ++
 kernel/latency_trace.c           |   26 +++++++++++++++++++++++---
 kernel/softirq.c                 |    6 +++---
 7 files changed, 33 insertions(+), 10 deletions(-)

Index: linux/arch/x86/kernel/stacktrace.c
===================================================================
--- linux.orig/arch/x86/kernel/stacktrace.c
+++ linux/arch/x86/kernel/stacktrace.c
@@ -22,7 +22,7 @@ static int save_stack_stack(void *data, 
 	return -1;
 }
 
-static void save_stack_address(void *data, unsigned long addr)
+static void notrace save_stack_address(void *data, unsigned long addr)
 {
 	struct stack_trace *trace = (struct stack_trace *)data;
 	if (trace->skip > 0) {
Index: linux/arch/x86/power/cpu.c
===================================================================
--- linux.orig/arch/x86/power/cpu.c
+++ linux/arch/x86/power/cpu.c
@@ -123,8 +123,9 @@ void __restore_processor_state(struct sa
 	mcheck_init(&boot_cpu_data);
 }
 
-void restore_processor_state(void)
+void notrace restore_processor_state(void)
 {
+	trace_resume();
 	__restore_processor_state(&saved_context);
 }
 
Index: linux/drivers/acpi/namespace/nsutils.c
===================================================================
--- linux.orig/drivers/acpi/namespace/nsutils.c
+++ linux/drivers/acpi/namespace/nsutils.c
@@ -923,7 +923,7 @@ struct acpi_namespace_node *acpi_ns_get_
  *
  ******************************************************************************/
 
-struct acpi_namespace_node *acpi_ns_get_next_valid_node(struct
+struct acpi_namespace_node * notrace acpi_ns_get_next_valid_node(struct
 							acpi_namespace_node
 							*node)
 {
Index: linux/drivers/acpi/namespace/nswalk.c
===================================================================
--- linux.orig/drivers/acpi/namespace/nswalk.c
+++ linux/drivers/acpi/namespace/nswalk.c
@@ -65,7 +65,7 @@ ACPI_MODULE_NAME("nswalk")
  *              within Scope is returned.
  *
  ******************************************************************************/
-struct acpi_namespace_node *acpi_ns_get_next_node(acpi_object_type type, struct acpi_namespace_node
+struct acpi_namespace_node * notrace acpi_ns_get_next_node(acpi_object_type type, struct acpi_namespace_node
 						  *parent_node, struct acpi_namespace_node
 						  *child_node)
 {
Index: linux/include/linux/sched.h
===================================================================
--- linux.orig/include/linux/sched.h
+++ linux/include/linux/sched.h
@@ -337,6 +337,7 @@ static inline void touch_all_softlockup_
   extern long user_trace_stop(void);
   extern void trace_cmdline(void);
   extern void init_tracer(void);
+  extern void trace_resume(void);
 #else
 # define mcount_enabled				0
 # define trace_enabled				0
@@ -358,6 +359,7 @@ static inline void touch_all_softlockup_
 # define user_trace_stop()			do { } while (0)
 # define trace_cmdline()			do { } while (0)
 # define init_tracer()				do { } while (0)
+# define trace_resume()				do { } while (0)
 #endif
 
 #ifdef CONFIG_WAKEUP_TIMING
Index: linux/kernel/latency_trace.c
===================================================================
--- linux.orig/kernel/latency_trace.c
+++ linux/kernel/latency_trace.c
@@ -258,19 +258,28 @@ static struct cpu_trace cpu_traces[NR_CP
 #endif
  } };
 
-static notrace cycle_t now(struct cpu_trace *tr, int monotonic)
+static inline notrace cycle_t __now(int monotonic)
 {
-	cycles_t now, delta, last = tr->last_cycles;
+	cycles_t now;
 
 	if (trace_use_raw_cycles && !monotonic)
 		now = get_cycles();
 	else
 		now = get_monotonic_cycles();
 
+	return now;
+}
+
+static notrace cycle_t now(struct cpu_trace *tr, int monotonic)
+{
+	cycles_t now, delta, last = tr->last_cycles;
+
+	now = __now(monotonic);
+
 	/*
 	 * Protect against time warps:
 	 */
-	if (unlikely(now < last))
+	if (unlikely(now < last || !last))
 		delta = 1;
 	else
 		delta = now - last;
@@ -281,6 +290,17 @@ static notrace cycle_t now(struct cpu_tr
 	return tr->cycles;
 }
 
+/*
+ * Resume callback - ignore any time spent resumed:
+ * (the clocksource readout might be unreliable anyway)
+ */
+void notrace trace_resume(void)
+{
+	struct cpu_trace *tr = cpu_traces + raw_smp_processor_id();
+
+	tr->last_cycles = 0;
+	mcount();
+}
 
 #ifdef CONFIG_EVENT_TRACE
 
Index: linux/kernel/softirq.c
===================================================================
--- linux.orig/kernel/softirq.c
+++ linux/kernel/softirq.c
@@ -91,7 +91,7 @@ static inline void __local_bh_disable(un
 }
 #endif /* CONFIG_TRACE_IRQFLAGS */
 
-void local_bh_disable(void)
+void notrace local_bh_disable(void)
 {
 	__local_bh_disable((unsigned long)__builtin_return_address(0));
 }
@@ -129,7 +129,7 @@ void _local_bh_enable(void)
 
 EXPORT_SYMBOL(_local_bh_enable);
 
-void local_bh_enable(void)
+void notrace local_bh_enable(void)
 {
 #ifdef CONFIG_TRACE_IRQFLAGS
 	unsigned long flags;
@@ -163,7 +163,7 @@ void local_bh_enable(void)
 }
 EXPORT_SYMBOL(local_bh_enable);
 
-void local_bh_enable_ip(unsigned long ip)
+void notrace local_bh_enable_ip(unsigned long ip)
 {
 #ifdef CONFIG_TRACE_IRQFLAGS
 	unsigned long flags;

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-18 16:21             ` Ingo Molnar
@ 2007-11-18 17:37               ` Mark Lord
  0 siblings, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-18 17:37 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, Thomas Gleixner, len.brown, Andrew Morton,
	Linux Kernel, linux-pm, rjw

Ingo Molnar wrote:
> * Mark Lord <lkml@rtr.ca> wrote:
> 
>> Since Ingo's latency trace patches lock up the machine on resume, the 
>> next thing I'll try instead is to re-enable CONFIG_IRQBALANCE=y.
> 
> hm, which patch did you try? Could you check whether all chunks from the 
> patch below are applied? (these are the fixed i did when i was doing 
> cross-suspend traces - this is not something i've done before, so the 
> tracer had to be adjusted)
..

Hi Ingo!

I was using your 2.6.23.1 version of the patches, plus the fix you posted.

The new patch you gave just now is for 2.6.24, which won't apply to
the older kernel.  I'm not switching kernels yet, as doing so might mask
the problem without actually resolving it for good.

Cheers

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] New Kernel Bugs
  2007-11-17 12:20                               ` Adrian Bunk
@ 2007-11-18 18:01                                 ` Theodore Tso
  0 siblings, 0 replies; 268+ messages in thread
From: Theodore Tso @ 2007-11-18 18:01 UTC (permalink / raw)
  To: Adrian Bunk
  Cc: Daniel Barkalow, Romano Giannetti, Benoit Boissinot, Mark Lord,
	Ingo Molnar, Andrew Morton, David Miller, protasnb, linux-kernel

On Sat, Nov 17, 2007 at 01:20:10PM +0100, Adrian Bunk wrote:
> > But a bisect takes around 7 compiles.
> >...
> 
> I don't understand that number.
> 
> The common case are regressions in -rc1, and a bisection of
> at about 7000 commits takes around 13 compiles.

Worst case it would take 13.  In practice I've seen less.  Part of it
is I suspect that I'm starting with something more recent than the
previous 2.6.23, but rather a daily -git13 or -git14 tree.  Part of it
may be because git can sometimes be more efficient by cutting off
entire branches with trail builds, since git history isn't completely
linear, but rather pulls of various branches together.

	    	   	    	    - Ted

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: Use *poof* for linux-omap
  2007-11-17  0:45                             ` Use *poof* for linux-omap David Miller
@ 2007-11-18 20:01                               ` Tony Lindgren
  0 siblings, 0 replies; 268+ messages in thread
From: Tony Lindgren @ 2007-11-18 20:01 UTC (permalink / raw)
  To: David Miller; +Cc: linux-kernel

* David Miller <davem@davemloft.net> [071116 16:46]:
> From: Tony Lindgren <tony@atomide.com>
> Date: Fri, 16 Nov 2007 14:16:11 -0800
> 
> > Can you please use your *poof* trick one more time to set up
> > linux-omap@vger.kernel.org?
> 
> Done, enjoy.

Thanks!

Tony

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 22:24                                               ` Rob Mueller
@ 2007-11-18 23:13                                                 ` Daniel Phillips
  2007-11-19  3:41                                                   ` Bron Gondwana
  0 siblings, 1 reply; 268+ messages in thread
From: Daniel Phillips @ 2007-11-18 23:13 UTC (permalink / raw)
  To: Rob Mueller
  Cc: Linus Torvalds, Peter Zijlstra, Bron Gondwana, Christian Kujau,
	Andrew Morton, Linux Kernel Mailing List, riel,
	Anton Altaparmakov

On Thursday 15 November 2007 14:24, Rob Mueller wrote:
> > That's my personal opinion, and I realize that some of the
> > commercial vendors may care about their insane customers'
> > satisfaction, but I'm simply not interested in insane users. If
> > they have that much RAM (and bought it a few years ago when a
> > 64-bit CPU wasn't an option), they can't be poor.
>
> From our perspective, the main issue is that some of these machines
> we spent quite a bit of money on the big RAM (for it's day) + lots of
> 15k RPM SCSI drives + multi-year support contracts. They're highly IO
> bound, and barely use 10-20% of their old 2.4Ghz Prestonia Xeon CPUs.
> It's hard to justify junking those machines < 5 years.
>
> We have a couple of 6G machines and some 8G machines using PAE. On
> the whole, they actually have been working really well (hmmm, apart
> from the recent dirty pages issue + reiserfs data=journal leaks +
> inodes in lowmem limits)

Junk everything except the 15K drives, you will be glad you did.  Too 
bad about those multi-year support contracts, hopefully you got a deal 
on them.

Prediction: after these dirty pages issues are gone, there will be more 
dirty page issues because the notion of dirty page limit is 
fundamentally broken.  Your smartest recourse is to re-motherboard to a 
place where the dirty page limit borkage does not hurt as much, and in 
the process you will get a cheap hardware upgrade.  Everybody will be 
happy, the sun will come out, the birds will sing.

Regards,

Daniel

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-18 23:13                                                 ` Daniel Phillips
@ 2007-11-19  3:41                                                   ` Bron Gondwana
  0 siblings, 0 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-19  3:41 UTC (permalink / raw)
  To: Daniel Phillips
  Cc: Rob Mueller, Linus Torvalds, Peter Zijlstra, Bron Gondwana,
	Christian Kujau, Andrew Morton, Linux Kernel Mailing List, riel,
	Anton Altaparmakov

On Sun, Nov 18, 2007 at 04:13:18PM -0700, Daniel Phillips wrote:
> On Thursday 15 November 2007 14:24, Rob Mueller wrote:
> > > That's my personal opinion, and I realize that some of the
> > > commercial vendors may care about their insane customers'
> > > satisfaction, but I'm simply not interested in insane users. If
> > > they have that much RAM (and bought it a few years ago when a
> > > 64-bit CPU wasn't an option), they can't be poor.
> >
> > From our perspective, the main issue is that some of these machines
> > we spent quite a bit of money on the big RAM (for it's day) + lots of
> > 15k RPM SCSI drives + multi-year support contracts. They're highly IO
> > bound, and barely use 10-20% of their old 2.4Ghz Prestonia Xeon CPUs.
> > It's hard to justify junking those machines < 5 years.
> >
> > We have a couple of 6G machines and some 8G machines using PAE. On
> > the whole, they actually have been working really well (hmmm, apart
> > from the recent dirty pages issue + reiserfs data=journal leaks +
> > inodes in lowmem limits)
> 
> Junk everything except the 15K drives, you will be glad you did.  Too 
> bad about those multi-year support contracts, hopefully you got a deal 
> on them.

Actually, the 15K drives are the bit we're getting the least use out
of now, since we're moving everything to external SATA units that
are more easily swapable.
 
> Prediction: after these dirty pages issues are gone, there will be more 
> dirty page issues because the notion of dirty page limit is 
> fundamentally broken.  Your smartest recourse is to re-motherboard to a 
> place where the dirty page limit borkage does not hurt as much, and in 
> the process you will get a cheap hardware upgrade.  Everybody will be 
> happy, the sun will come out, the birds will sing.

Or just keep running 2.6.16 where it's all been working quite fine
thanks very much, or maintain a simple patch that rips all that out
since we don't care too much about "fairness" - we only run a couple
of things on that machine and they run fine.

Bron ( going to settle down and really test this stuff to make sure
       we have an acceptable "fix" for us then do it! )

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:14                                         ` Linus Torvalds
  2007-11-15 21:26                                           ` Linus Torvalds
  2007-11-15 21:26                                           ` Peter Zijlstra
@ 2007-11-19  3:54                                           ` Bron Gondwana
  2007-11-22  3:42                                           ` [PATCH 1/1] mm: add dirty_highmem option Bron Gondwana
  3 siblings, 0 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-19  3:54 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Peter Zijlstra, Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm

On Thu, Nov 15, 2007 at 01:14:32PM -0800, Linus Torvalds wrote:
 
Sorry about not replying to this earlier.  I actually got a weekend
away from the computer pretty much last weekend - took the kids
swimming, helped a friend clear dead wood from around her house
before the fire season.  Shocking I know.
 
> On Thu, 15 Nov 2007, Linus Torvalds wrote:
> > 
> > Unacceptable. We used to do exactly what your patch does, and it got fixed 
> > once. We're not introducing that fundamentally broken concept again.
> 
> Examples of non-broken solutions:
>  (a) always use lowmem sizes (what we do now)
>  (b) always use total mem sizes (sane but potentially dangerous: but the 
>      VM pressure should work! It has serious bounce-buffer issues, though, 
>      which is why I think it's crazy even if it's otherwise consistent)
>  (c) make all dirty counting be *purely* per-bdi, so that everybody can 
>      disagree on what the limits are, but at least they also then use 
>      different counters
> 
> So it's just the "different writers look at the same dirty counts but then 
> interpret it to mean totally different things" that I think is so 
> fundamentally bogus. I'm not claiming that what we do now is the only way 
> to do things, I just don't think your approach is tenable.
> 
> Btw, I actually suspect that while (a) is what we do now, for the specific 
> case that Bron has, we could have a /proc/sys/vm option to just enable 
> (b). So we don't have to have just one consistent model, we can allow odd 
> users (and Bron sounds like one - sorry Bron ;) to just force other, odd, 
> but consistent models.

Hey, if Andrew Morton can tell us we find all the interesting bugs, you
can call me odd.  I've been called worse!

We also run ReiserFS (3 of course, I tried 4 and it et my laptop disk)
on all our production IMAP servers.  Tried ext3 and the performance was
so horrible that our users hated us (and I hated being woken in the
night by things timing out and paging me).  And I'm spending far too
long still writing C thanks to Cyrus having enough bugs to keep me busy
for the rest of my natural life if I don't break and go write my own
IMAP server at some point. *clears throat*

> I'd also like to point out that while the "bounce buffer" issue is not so 
> much a HIGHMEM issue on its own (it's really about the device DMA limits, 
> which are _independent_ of HIGHMEM, of course), the reason HIGHMEM is 
> special is that without HIGHMEM the bounce buffers generally work 
> perfectly fine.
> 
> The problem with HIGHMEM is that it causes various metadata (dentries, 
> inodes, page struct tables etc) to eat up memory "prime real estate" under 
> the same kind of conditions that also dirty a lot of memory. So the reason 
> we disallow HIGHMEM from dirty limits is only *partly* the per-device or 
> mapping DMA limits, and to a large degree the fact that non-highmem memory 
> is special in general, and it is usually the non-highmem areas that are 
> constrained - and need to be protected.

I'm going to finish off writing a decent test case so I can reliably
reproduce the problem first, and then go compile a small set of kernels
with the various patches that have been thrown around here and see if
they solve the problems for me.

Thankfully I don't have the same problem you do Linus - I don't care if
any particular patch isn't consistent - isn't fair in the general sense
- even "doesn't work for anyone else".  So long as it's stable and it
works on this machine I'm happy to support it through the next couple
of years until we either get a world facing 64 bit machine with the
spare capacity to run DCC or we drop DCC.

The only reason to upgrade the kernel there at all is keeping up-to-date
with security patches, and the relative tradeoffs of backporting (or
expecting Adrian Bunk to keep doing it for us) rather than maintaing
a small patch to keep the behaviour of one thing we like.

And to all of you in this thread (especially Linus and Peter) - thanks
heaps for grabbing on to a throw away line in an unrelated discussion
and putting the work in to:

a) explain the problem and the cause to me before I put in heaps of
   work tracking it down; and

b) putting together some patches for me to test.

I saw a couple of days ago someone posted an "Ask Slashdot" whether
6 weeks was an appropriate time for a software vendor to get a fix
out to a customer and implying that the customer was an unrealistic
whiner to expect anyone to be able to do better.  I'll be able to
point to this thread if anyone suggests that you can't get decent
support on Linux!

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: size of git repository (was Re: [BUG] New Kernel Bugs)
  2007-11-18 14:56                     ` Ingo Molnar
@ 2007-11-19  4:43                       ` Willy Tarreau
  0 siblings, 0 replies; 268+ messages in thread
From: Willy Tarreau @ 2007-11-19  4:43 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Pavel Machek, Mark Lord, Andrew Morton, David Miller, protasnb,
	linux-kernel, netdev, alsa-devel, linux-ide, linux-pcmcia,
	linux-input, bugme-daemon

On Sun, Nov 18, 2007 at 03:56:11PM +0100, Ingo Molnar wrote:
> 
> * Pavel Machek <pavel@ucw.cz> wrote:
> 
> > On Tue 2007-11-13 12:50:08, Mark Lord wrote:
> > > Ingo Molnar wrote:
> > > >
> > > >for example git-bisect was godsent. I remember that 
> > > >years ago bisection of a bug was a very laborous task 
> > > >so that it was only used as a final, last-ditch 
> > > >approach for really nasty bugs. Today we can 
> > > >autonomouly bisect build bugs via a simple shell 
> > > >command around "git-bisect run", without any human 
> > > >interaction! This freed up testing resources 
> > > ..
> > > 
> > > It's only a godsend for the few people who happen to be 
> > > kernel developers
> > > and who happen to already use git.
> > > 
> > > It's a 540MByte download over a slow link for everyone 
> > > else.
> > 
> > Hmmm, clean-cg is 7.7G on my machine, and yes I tried 
> > git-prune-packed. What am I doing wrong?
> 
> "git-repack -a -d" gives me ~220 MB:
> 
>   $ du -s .git
>   222064  .git
> 
> anyone who can download a 43 MB tar.bz2 tarball for a kernel release 
> should be able to afford a _one time_ download size of 250 MB (the size 
> of the current kernel.org git repository). If not, burning a CD or DVD 
> and carrying it home ought to do the trick. Git is very 
> bandwidth-efficient after that point - lots of people behind narrow 
> pipes are using it - it's just the initial clone that takes time. And 
> given all the history and metadata that the git repository carries (full 
> changelogs, annotations, etc.) it's a no-brainer that kernel developers 
> should be using it.
> 
> (and you can shrink the 250 MB further down by using shallow clones, 
> etc.)
> 
> yes, some people complained when distros stopped doing floppy installs. 
> Some people complained when distros stopped doing CD installs. Yes, i've 
> myself done a 250+ MB download over a 56 kbit modem in the past, and 
> while it indeed took overnight to finish, it's very much doable. It's 
> not really qualitatively different from the 1.5 hours a kernel tar.bz2 
> took to download.

Probably that once in a while, we should set up a complete tree in a
tar.bz2 format on kernel.org. It would help a lot of people behind small
pipes. I have been encountering problems with git-clone when the link is
unstable. After the smallest error, it erases everything and you have to
retry from start, which is quite frustrating and expensive.

At least, downloading a tar.bz2 with FTP would be easier and a lot more
reliable. Also, people could download it from their workplace and bring
it home.

Willy


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 21:47                                             ` Linus Torvalds
                                                                 ` (2 preceding siblings ...)
  2007-11-16  0:48                                               ` Alan Cox
@ 2007-11-21 21:25                                               ` Jan Engelhardt
  3 siblings, 0 replies; 268+ messages in thread
From: Jan Engelhardt @ 2007-11-21 21:25 UTC (permalink / raw)
  To: Linux Kernel Mailing List
  Cc: Linus Torvalds, Bron Gondwana, Christian Kujau, Andrew Morton,
	Peter Zijlstra, Linux Kernel Mailing List, robm


On Thu, 15 Nov 2007 13:47:54 -0800 (PST) Linus Torvalds wrote:
>
>But quite frankly, I refuse to even care about anything past that. If 
>you have 12G (or heaven forbid, even more) in your machine, and you 
>can't be bothered to just upgrade to a 64-bit CPU, then quite frankly, 
>*I* personally can't be bothered to care.
>
>If they have that much RAM (and bought it a few years ago when a 64-bit 
>CPU wasn't an option), they can't be poor.
>
>So the _only_ explanation today for 12GB on a 32-bit machine is
> (a) insanity
>or 
> (b) being so lazy as to not bother to upgrade
>

Just around the corner...

$ ftp ftp
Connected to ftp.gwdg.de.
220-====================================================================
220-Gesellschaft fuer wissenschaftliche Datenverarbeitung mbH Goettingen
220-====================================================================
220-This is a Linux PC (Dell PE-2650, 2 CPUs P4/2800, 12 GB RAM)
220-running SuSE-Linux-8.2 with SuSE kernel 2.4.20-64GB-SMP.

There is no reason to upgrade the hardware - if it works, hey good then.
And I am pretty sure that a few 2 GB sticks are cheaper than a big 
opteron (if you only go by that). It sure is now - and probably even 
back then.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-15 16:32                                 ` Linus Torvalds
  2007-11-15 19:40                                   ` Peter Zijlstra
@ 2007-11-21 23:51                                   ` Bron Gondwana
  2007-11-22  2:16                                     ` Bron Gondwana
  1 sibling, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-21 23:51 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Christian Kujau, Andrew Morton, Peter Zijlstra,
	Linux Kernel Mailing List, robm

On Thu, Nov 15, 2007 at 08:32:22AM -0800, Linus Torvalds wrote:
> On Thu, 15 Nov 2007, Bron Gondwana wrote:
> > 
> > I guess we'll be doing the one-liner kernel mod and testing
> > that then.
> 
> The thing to look at is "get_dirty_limits()" in mm/page-writeback.c, and 
> in this particular case it's the
> 
> 	unsigned long available_memory = determine_dirtyable_memory();
> 
> that's going to bite you. In particular, note the
> 
> 	x -= highmem_dirtyable_memory(x);
> 
> that we do in determine_dirtyable_memory().
> 
> So in this case, if you basically remove that line, it will allow all of 
> memory to be dirtied (including highmem), and then the background_ratio 
> will work on the whole 6GB.
> 
> HOWEVER! It's worth noting that we also have some other old legacy cruft 
> there that may interfere with your code. In particular, if you look at the 
> top of "get_dirty_limits()", it *also* does a
> 
>         unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
>                                 global_page_state(NR_ANON_PAGES)) * 100) /
>                                         available_memory;
> 
>         dirty_ratio = vm_dirty_ratio;
>         if (dirty_ratio > unmapped_ratio / 2)
>                 dirty_ratio = unmapped_ratio / 2;
> 
> and that whole "unmapped_ratio" comparison is probably bogus these days, 
> since we now take the mapped dirty pages into account. That code harks 
> back to the days before we did that, and dirty ratios only affected 
> non-mapped pages.
> 
> And in particular, now that I look at it, I wonder if it can even go 
> negative (because "available_memory" may be *smaller* than the 
> NR_FILE_MAPPED|ANON_PAGES sum!).
> 
> We'll fix up a negative value anyway (because of the clamping of 
> dirty_ratio to no less than 5), but the point is that the whole 
> "unmapped_ratio" thing probably doesn't make sense any more, and may well 
> make the dirty_ratio not work for you, because you may have a very small 
> unmapped_ratio that effectively makes all dirty limits always clamp to a 
> very small value.
> 
> So regardless, I think you may want to try the appended patch *first*.
> 
> If this patch makes a difference, please holler. I think it's the correct 
> thing to do, but I'm not going to actually commit it without somebody 
> saying that it makes a difference (and preferably Peter Zijlstra and 
> Andrew acking it too).

mmap: mmap call failed: errno: 12 errmsg: Cannot allocate memory

Yep, that's "fixed" the problem alright!  No way this puppy is
dirtying 2Gb of memory any more.

http://linux.brong.fastmail.fm/2007-11-22/bmtest.pl

That said, pushing the size down to 1700 rather than 2000 in that
file makes it run, and the behaviour matches the 2000 Mb case on
2.6.16.55 rather than 2.6.20.20 or 2.6.23.1 (my other test case
kernels that happened to be pre-built on that machine)

[root@lb1 ~]$ free
             total       used       free     shared    buffers     cached
Mem:       4149836    2073056    2076780          0      22036    1846096
-/+ buffers/cache:     204924    3944912
Swap:      2096472          0    2096472

That's after running the 1700Mb version.  You can see this machine is our
one remaining 4Gb machine (it's not running any production services unlike
the 6Gb machine, so it's better for testing)

Anyway - looks like this may be a "good enough" solution for out1 if
it can manage an ~2Gb file with 6Gb of memory available.  I'll test
that later today - but I should drag myself into the office now...

Bron.

(patch left attached below for reference)

> Only *after* testing this change is it probably a good idea to test the 
> real hack of then removing the highmem_dirtyable_memory() thing. 
> 
> Peter? Andrew?
> 
> 		Linus
> 
> ---
>  mm/page-writeback.c |    8 --------
>  1 files changed, 0 insertions(+), 8 deletions(-)
> 
> diff --git a/mm/page-writeback.c b/mm/page-writeback.c
> index 81a91e6..d55cfca 100644
> --- a/mm/page-writeback.c
> +++ b/mm/page-writeback.c
> @@ -297,20 +297,12 @@ get_dirty_limits(long *pbackground, long *pdirty, long *pbdi_dirty,
>  {
>  	int background_ratio;		/* Percentages */
>  	int dirty_ratio;
> -	int unmapped_ratio;
>  	long background;
>  	long dirty;
>  	unsigned long available_memory = determine_dirtyable_memory();
>  	struct task_struct *tsk;
>  
> -	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
> -				global_page_state(NR_ANON_PAGES)) * 100) /
> -					available_memory;
> -
>  	dirty_ratio = vm_dirty_ratio;
> -	if (dirty_ratio > unmapped_ratio / 2)
> -		dirty_ratio = unmapped_ratio / 2;
> -
>  	if (dirty_ratio < 5)
>  		dirty_ratio = 5;
>  

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs)
  2007-11-21 23:51                                   ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
@ 2007-11-22  2:16                                     ` Bron Gondwana
  0 siblings, 0 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-22  2:16 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: Linus Torvalds, Christian Kujau, Andrew Morton, Peter Zijlstra,
	Linux Kernel Mailing List, robm

On Thu, Nov 22, 2007 at 10:51:15AM +1100, Bron Gondwana wrote:
> On Thu, Nov 15, 2007 at 08:32:22AM -0800, Linus Torvalds wrote:
> > If this patch makes a difference, please holler. I think it's the correct 
> > thing to do, but I'm not going to actually commit it without somebody 
> > saying that it makes a difference (and preferably Peter Zijlstra and 
> > Andrew acking it too).
> 
> mmap: mmap call failed: errno: 12 errmsg: Cannot allocate memory
> 
> Yep, that's "fixed" the problem alright!  No way this puppy is
> dirtying 2Gb of memory any more.
> 
> http://linux.brong.fastmail.fm/2007-11-22/bmtest.pl

Alternatively perhaps I'm just a moron who used a config file with:
CONFIG_PAGE_OFFSET=0x80000000 set to build the new kernel (I hadn't
committed it because it turned out not to solve the issue it was
there for).  That would explain a few things.

[root@lb1 perl]$ free
             total       used       free     shared    buffers     cached
Mem:       4150620    2272284    1878336          0      11212    2066536
-/+ buffers/cache:     194536    3956084
Swap:      2096472          0    2096472

That's more the usage I would expect to see.

Now for the downside.  It works again, but it still runs slow.  Seems to
hit (and this is totally unscientific, I'm just watching the numbers
scroll by) at about 120000 writes rather than 70000 writes, but that's
still not fitting the while file dirty.

I notice that PF_LESS_THROTTLE gets set by nfsd to get an extra 25%
bonus free space allocated.  Potentially dcc could use similar tricks
to claim extra space if that knob is available up in userspace.  I'm
happy to patch dcc as well if I have to, I'm already backporting it,
so adding another little quilt directory and applying it is pretty
trivial (must try guilt/stgit one of these days)

Bron.



^ permalink raw reply	[flat|nested] 268+ messages in thread

* [PATCH 1/1] mm: add dirty_highmem option
  2007-11-15 21:14                                         ` Linus Torvalds
                                                             ` (2 preceding siblings ...)
  2007-11-19  3:54                                           ` Bron Gondwana
@ 2007-11-22  3:42                                           ` Bron Gondwana
  2007-11-26 17:53                                             ` Linus Torvalds
  2007-11-27  4:54                                             ` Andrew Morton
  3 siblings, 2 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-22  3:42 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Peter Zijlstra, Bron Gondwana, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm

On Thu, Nov 15, 2007 at 01:14:32PM -0800, Linus Torvalds wrote:
> Examples of non-broken solutions:
>  (a) always use lowmem sizes (what we do now)
>  (b) always use total mem sizes (sane but potentially dangerous: but the 
>      VM pressure should work! It has serious bounce-buffer issues, though, 
>      which is why I think it's crazy even if it's otherwise consistent)
> 
> Btw, I actually suspect that while (a) is what we do now, for the specific 
> case that Bron has, we could have a /proc/sys/vm option to just enable 
> (b). So we don't have to have just one consistent model, we can allow odd 
> users (and Bron sounds like one - sorry Bron ;) to just force other, odd, 
> but consistent models.

A 32 bit machine with HIGHMEM64 enabled running DCC has an MMAPed file
of approximately 2Gb size which contains a hash format that is written
"randomly" by the dbclean process.  On 2.6.16 this process took a few
minutes.  With lowmem only accounting of dirty ratios, this takes about
12 hours of 100% disk IO, all random writes.

This patch includes some code cleanup from Linus and a toggle in
/proc/sys/vm/dirty_highmem which can be set to 1 to add the highmem
back to the total available memory count.

Signed-off-by: Bron Gondwana <brong@fastmail.fm>

Index: linux-2.6.23.8-reiserfix-fai-vmdirty/mm/page-writeback.c
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/mm/page-writeback.c	2007-11-22 01:48:20.000000000 +0000
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/mm/page-writeback.c	2007-11-22 02:42:04.000000000 +0000
@@ -70,6 +70,12 @@ static inline long sync_writeback_pages(
 int dirty_background_ratio = 5;
 
 /*
+ * free highmem will not be subtracted from the total free memory
+ * for calculating free ratios if vm_dirty_highmem is true
+ */
+int vm_dirty_highmem;
+
+/*
  * The generator of dirty data starts writeback at this percentage
  */
 int vm_dirty_ratio = 10;
@@ -153,7 +159,8 @@ static unsigned long determine_dirtyable
 	x = global_page_state(NR_FREE_PAGES)
 		+ global_page_state(NR_INACTIVE)
 		+ global_page_state(NR_ACTIVE);
-	x -= highmem_dirtyable_memory(x);
+	if (!vm_dirty_highmem)
+		x -= highmem_dirtyable_memory(x);
 	return x + 1;	/* Ensure that we never return 0 */
 }
 
@@ -163,20 +170,12 @@ get_dirty_limits(long *pbackground, long
 {
 	int background_ratio;		/* Percentages */
 	int dirty_ratio;
-	int unmapped_ratio;
 	long background;
 	long dirty;
 	unsigned long available_memory = determine_dirtyable_memory();
 	struct task_struct *tsk;
 
-	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
-				global_page_state(NR_ANON_PAGES)) * 100) /
-					available_memory;
-
 	dirty_ratio = vm_dirty_ratio;
-	if (dirty_ratio > unmapped_ratio / 2)
-		dirty_ratio = unmapped_ratio / 2;
-
 	if (dirty_ratio < 5)
 		dirty_ratio = 5;
 
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/include/linux/writeback.h
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/include/linux/writeback.h	2007-10-09 20:31:38.000000000 +0000
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/include/linux/writeback.h	2007-11-22 01:48:21.000000000 +0000
@@ -92,6 +92,7 @@ void throttle_vm_writeout(gfp_t gfp_mask
 
 /* These are exported to sysctl. */
 extern int dirty_background_ratio;
+extern int vm_dirty_highmem;
 extern int vm_dirty_ratio;
 extern int dirty_writeback_interval;
 extern int dirty_expire_interval;
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/kernel/sysctl.c
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/kernel/sysctl.c	2007-10-09 20:31:38.000000000 +0000
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/kernel/sysctl.c	2007-11-22 01:48:21.000000000 +0000
@@ -776,6 +776,7 @@ static ctl_table kern_table[] = {
 /* Constants for minimum and maximum testing in vm_table.
    We use these as one-element integer vectors. */
 static int zero;
+static int one = 1;
 static int two = 2;
 static int one_hundred = 100;
 
@@ -1066,6 +1067,19 @@ static ctl_table vm_table[] = {
 		.extra1		= &zero,
 	},
 #endif
+#ifdef CONFIG_HIGHMEM
+	{
+		.ctl_name	= CTL_UNNUMBERED,
+		.procname	= "dirty_highmem",
+		.data		= &vm_dirty_highmem,
+		.maxlen		= sizeof(vm_dirty_highmem),
+		.mode		= 0644,
+		.proc_handler	= &proc_dointvec_minmax,
+		.strategy	= &sysctl_intvec,
+		.extra1		= &zero,
+		.extra2		= &one,
+	},
+#endif
 /*
  * NOTE: do not add new entries to this table unless you have read
  * Documentation/sysctl/ctl_unnumbered.txt
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/filesystems/proc.txt
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/Documentation/filesystems/proc.txt	2007-11-22 02:32:36.000000000 +0000
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/filesystems/proc.txt	2007-11-22 02:39:11.000000000 +0000
@@ -1229,6 +1229,18 @@ dirty_background_ratio
 Contains, as a percentage of total system memory, the number of pages at which
 the pdflush background writeback daemon will start writing out dirty data.
 
+dirty_highmem
+-------------
+
+Contains, as a boolean, a switch to allow highmem to be counted as
+part of the "available" memory against which the dirty ratios will be
+applied.
+
+Setting this to 1 can be useful on 32 bit machines where you want to make
+random changes within an MMAPed file that is larger than your available
+lowmem, however it is potentially dangerous and has serious bounce-buffer
+issues.
+
 dirty_ratio
 -----------------
 
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/sysctl/vm.txt
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/Documentation/sysctl/vm.txt	2007-11-22 02:31:32.000000000 +0000
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/sysctl/vm.txt	2007-11-22 02:32:31.000000000 +0000
@@ -18,6 +18,7 @@ files can be found in mm/swap.c.
 Currently, these files are in /proc/sys/vm:
 - overcommit_memory
 - page-cluster
+- dirty_highmem
 - dirty_ratio
 - dirty_background_ratio
 - dirty_expire_centisecs
@@ -36,10 +37,10 @@ Currently, these files are in /proc/sys/
 
 ==============================================================
 
-dirty_ratio, dirty_background_ratio, dirty_expire_centisecs,
-dirty_writeback_centisecs, vfs_cache_pressure, laptop_mode,
-block_dump, swap_token_timeout, drop-caches,
-hugepages_treat_as_movable:
+dirty_highmem, dirty_ratio, dirty_background_ratio, 
+dirty_expire_centisecs, dirty_writeback_centisecs, 
+vfs_cache_pressure, laptop_mode, block_dump, 
+swap_token_timeout, drop-caches, hugepages_treat_as_movable:
 
 See Documentation/filesystems/proc.txt
 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [PATCH 1/1] mm: add dirty_highmem option
  2007-11-22  3:42                                           ` [PATCH 1/1] mm: add dirty_highmem option Bron Gondwana
@ 2007-11-26 17:53                                             ` Linus Torvalds
  2007-11-27  1:30                                               ` Bron Gondwana
  2007-11-27  4:54                                             ` Andrew Morton
  1 sibling, 1 reply; 268+ messages in thread
From: Linus Torvalds @ 2007-11-26 17:53 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: Peter Zijlstra, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm



On Thu, 22 Nov 2007, Bron Gondwana wrote:
> 
> This patch includes some code cleanup from Linus and a toggle in
> /proc/sys/vm/dirty_highmem which can be set to 1 to add the highmem
> back to the total available memory count.

Just to verify - can you confirm that this "just fixes it" for you?

I think this is the right approach to take, and seems very safe (ie people 
who know that their loads are ok can just set the flag), but I do want to 
verify that there was nothing else going on, and that you now see the same 
performance as you did in 2.6.16?

The other alternative, of course, would be to simply allow the dirty 
percentages to be > 100%, but that's just *odd* ;)

		Linus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [PATCH 1/1] mm: add dirty_highmem option
  2007-11-26 17:53                                             ` Linus Torvalds
@ 2007-11-27  1:30                                               ` Bron Gondwana
  0 siblings, 0 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-27  1:30 UTC (permalink / raw)
  To: Linus Torvalds
  Cc: Bron Gondwana, Peter Zijlstra, Christian Kujau, Andrew Morton,
	Linux Kernel Mailing List, robm

On Mon, Nov 26, 2007 at 09:53:17AM -0800, Linus Torvalds wrote:
> 
> 
> On Thu, 22 Nov 2007, Bron Gondwana wrote:
> > 
> > This patch includes some code cleanup from Linus and a toggle in
> > /proc/sys/vm/dirty_highmem which can be set to 1 to add the highmem
> > back to the total available memory count.
> 
> Just to verify - can you confirm that this "just fixes it" for you?
> 
> I think this is the right approach to take, and seems very safe (ie people 
> who know that their loads are ok can just set the flag), but I do want to 
> verify that there was nothing else going on, and that you now see the same 
> performance as you did in 2.6.16?
> 
> The other alternative, of course, would be to simply allow the dirty 
> percentages to be > 100%, but that's just *odd* ;)

Yes, toggling dirty_highmem "just fixes it" in all our tests.  I hadn't
tested it on the production machine yet - but I'm just installing it
there now since it's been running fine on a less important machine for
a few days now.

I did wonder about allowing the dirty percentage to go way up, but that
would have cause "this one goes up to 110%" comments in the sysctl
limits code and people would have thought I was childish.  Can't have
that.  Much better to have "int one = 1" instead.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [PATCH 1/1] mm: add dirty_highmem option
  2007-11-22  3:42                                           ` [PATCH 1/1] mm: add dirty_highmem option Bron Gondwana
  2007-11-26 17:53                                             ` Linus Torvalds
@ 2007-11-27  4:54                                             ` Andrew Morton
  2007-11-27  5:24                                               ` Bron Gondwana
  1 sibling, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-27  4:54 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: Linus Torvalds, Peter Zijlstra, Christian Kujau,
	Linux Kernel Mailing List, robm

On Thu, 22 Nov 2007 14:42:04 +1100 Bron Gondwana <brong@fastmail.fm> wrote:

>  /*
> + * free highmem will not be subtracted from the total free memory
> + * for calculating free ratios if vm_dirty_highmem is true
> + */
> +int vm_dirty_highmem;

One would expect that setting dirty_highmem to true would cause highmem to
be accounted in dirty-memory calculations.  However with this change
reality is in fact the inverse of that.

So how about this?

 Documentation/filesystems/proc.txt |    4 ++--
 mm/page-writeback.c                |    8 ++++----
 2 files changed, 6 insertions(+), 6 deletions(-)

diff -puN Documentation/filesystems/proc.txt~mm-add-dirty_highmem-option-fix Documentation/filesystems/proc.txt
--- a/Documentation/filesystems/proc.txt~mm-add-dirty_highmem-option-fix
+++ a/Documentation/filesystems/proc.txt
@@ -1265,8 +1265,8 @@ Contains, as a boolean, a switch to allo
 part of the "available" memory against which the dirty ratios will be
 applied.
 
-Setting this to 1 can be useful on 32 bit machines where you want to make
-random changes within an MMAPed file that is larger than your available
+Setting this to 0 (false) can be useful on 32 bit machines where you wish to
+make random changes within an MMAPed file that is larger than your available
 lowmem, however it is potentially dangerous and has serious bounce-buffer
 issues.
 
diff -puN mm/page-writeback.c~mm-add-dirty_highmem-option-fix mm/page-writeback.c
--- a/mm/page-writeback.c~mm-add-dirty_highmem-option-fix
+++ a/mm/page-writeback.c
@@ -69,10 +69,10 @@ static inline long sync_writeback_pages(
 int dirty_background_ratio = 5;
 
 /*
- * free highmem will not be subtracted from the total free memory
- * for calculating free ratios if vm_dirty_highmem is true
+ * free highmem will be subtracted from the total free memory for calculating
+ * free ratios if vm_dirty_highmem is true
  */
-int vm_dirty_highmem;
+int vm_dirty_highmem = 1;
 
 /*
  * The generator of dirty data starts writeback at this percentage
@@ -293,7 +293,7 @@ static unsigned long determine_dirtyable
 	x = global_page_state(NR_FREE_PAGES)
 		+ global_page_state(NR_INACTIVE)
 		+ global_page_state(NR_ACTIVE);
-	if (!vm_dirty_highmem)
+	if (vm_dirty_highmem)
 		x -= highmem_dirtyable_memory(x);
 	return x + 1;	/* Ensure that we never return 0 */
 }
_




(I dropped the already-merged part of your patch)

(I fixed a build error in kernel/sysctl.c: "one" was defined twice when
suitable config options were set).

(It's an unpleasing patch, btw.  But it's an unpleasant problem and at least
this way people can tell us "hey, I did <this> and it started to work")

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [PATCH 1/1] mm: add dirty_highmem option
  2007-11-27  4:54                                             ` Andrew Morton
@ 2007-11-27  5:24                                               ` Bron Gondwana
  2007-11-27  5:53                                                 ` Andrew Morton
  0 siblings, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-27  5:24 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Linus Torvalds, Peter Zijlstra, Christian Kujau,
	Linux Kernel Mailing List, Rob Mueller

On Mon, 26 Nov 2007 20:54:28 -0800, "Andrew Morton" <akpm@linux-foundation.org> said:
> On Thu, 22 Nov 2007 14:42:04 +1100 Bron Gondwana <brong@fastmail.fm>
> wrote:
> 
> >  /*
> > + * free highmem will not be subtracted from the total free memory
> > + * for calculating free ratios if vm_dirty_highmem is true
> > + */
> > +int vm_dirty_highmem;
> 
> One would expect that setting dirty_highmem to true would cause highmem
> to
> be accounted in dirty-memory calculations.  However with this change
> reality is in fact the inverse of that.
> 
> So how about this?

Actually, I'm confused now.  Maybe I chose a bad name to begin with.
Does it mean "I am allowed to dirty high memory" or "my high memory
will be dirty if this is on"?

Hmm... I'm even having trouble articulating what's odd about it.

I guess my internal model was: "if this flag is set then you are
allowed to make high memory dirty without needing to flush it
immediately", which is why I made it that way around.


No - you're wrong.  My patch _did_ include high memory in the dirty
memory calculations when dirty_highmem was true.

>  	x = global_page_state(NR_FREE_PAGES)
>  		+ global_page_state(NR_INACTIVE)
>  		+ global_page_state(NR_ACTIVE);

This is the total memory, _including_ high memory.

>           x -= highmem_dirtyable_memory(x);

This removes the high memory from the total count.


I think I got it right.  If dirty_highmem is set to true, then
don't subtract highmem from the total memory count before
calculating the percentages.  That's what I meant, and that's
what the toggle did.  Removed the subtraction.

Bron.


>  Documentation/filesystems/proc.txt |    4 ++--
>  mm/page-writeback.c                |    8 ++++----
>  2 files changed, 6 insertions(+), 6 deletions(-)
> 
> diff -puN
> Documentation/filesystems/proc.txt~mm-add-dirty_highmem-option-fix
> Documentation/filesystems/proc.txt
> --- a/Documentation/filesystems/proc.txt~mm-add-dirty_highmem-option-fix
> +++ a/Documentation/filesystems/proc.txt
> @@ -1265,8 +1265,8 @@ Contains, as a boolean, a switch to allo
>  part of the "available" memory against which the dirty ratios will be
>  applied.
>  
> -Setting this to 1 can be useful on 32 bit machines where you want to
> make
> -random changes within an MMAPed file that is larger than your available
> +Setting this to 0 (false) can be useful on 32 bit machines where you
> wish to
> +make random changes within an MMAPed file that is larger than your
> available
>  lowmem, however it is potentially dangerous and has serious
>  bounce-buffer
>  issues.
>  
> diff -puN mm/page-writeback.c~mm-add-dirty_highmem-option-fix
> mm/page-writeback.c
> --- a/mm/page-writeback.c~mm-add-dirty_highmem-option-fix
> +++ a/mm/page-writeback.c
> @@ -69,10 +69,10 @@ static inline long sync_writeback_pages(
>  int dirty_background_ratio = 5;
>  
>  /*
> - * free highmem will not be subtracted from the total free memory
> - * for calculating free ratios if vm_dirty_highmem is true
> + * free highmem will be subtracted from the total free memory for
> calculating
> + * free ratios if vm_dirty_highmem is true
>   */
> -int vm_dirty_highmem;
> +int vm_dirty_highmem = 1;
>  
>  /*
>   * The generator of dirty data starts writeback at this percentage
> @@ -293,7 +293,7 @@ static unsigned long determine_dirtyable
>  	x = global_page_state(NR_FREE_PAGES)
>  		+ global_page_state(NR_INACTIVE)
>  		+ global_page_state(NR_ACTIVE);
> -	if (!vm_dirty_highmem)
> +	if (vm_dirty_highmem)
>  		x -= highmem_dirtyable_memory(x);
>  	return x + 1;	/* Ensure that we never return 0 */
>  }
> _
> 
> 
> 
> 
> (I dropped the already-merged part of your patch)
> 
> (I fixed a build error in kernel/sysctl.c: "one" was defined twice when
> suitable config options were set).
> 
> (It's an unpleasing patch, btw.  But it's an unpleasant problem and at
> least
> this way people can tell us "hey, I did <this> and it started to work")
-- 
  Bron Gondwana
  brong@fastmail.fm


^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [PATCH 1/1] mm: add dirty_highmem option
  2007-11-27  5:24                                               ` Bron Gondwana
@ 2007-11-27  5:53                                                 ` Andrew Morton
  2007-11-27 12:10                                                   ` dirty highmem calculation sysctl name (Was: [PATCH 1/1] mm: add dirty_highmem option) Bron Gondwana
  0 siblings, 1 reply; 268+ messages in thread
From: Andrew Morton @ 2007-11-27  5:53 UTC (permalink / raw)
  To: Bron Gondwana
  Cc: Linus Torvalds, Peter Zijlstra, Christian Kujau,
	Linux Kernel Mailing List, Rob Mueller

On Tue, 27 Nov 2007 16:24:24 +1100 "Bron Gondwana" <brong@fastmail.fm> wrote:

> On Mon, 26 Nov 2007 20:54:28 -0800, "Andrew Morton" <akpm@linux-foundation.org> said:
> > On Thu, 22 Nov 2007 14:42:04 +1100 Bron Gondwana <brong@fastmail.fm>
> > wrote:
> > 
> > >  /*
> > > + * free highmem will not be subtracted from the total free memory
> > > + * for calculating free ratios if vm_dirty_highmem is true
> > > + */
> > > +int vm_dirty_highmem;
> > 
> > One would expect that setting dirty_highmem to true would cause highmem
> > to
> > be accounted in dirty-memory calculations.  However with this change
> > reality is in fact the inverse of that.
> > 
> > So how about this?
> 
> Actually, I'm confused now.  Maybe I chose a bad name to begin with.
> Does it mean "I am allowed to dirty high memory" or "my high memory
> will be dirty if this is on"?

But we're always allowed to dirty highmem - there'd be no point in having
it otherwise.  Hence the term dirty_highmem is confusing.

umm, really you want
/proc/sys/vm/dont-account-highmem-in-dirty-memory-calculations, only
shorter.

Do you agree?

If so, then it's still not a very pleasing interface - setting something to
"true" to disable a particular piece of kernel behaviour implies a single
negation which we don't really need.

It would be simpler to have
/proc/sys/vm/do-account-highmem-in-dirty-memory-calculations,
defaulting to "true" - this has no negations.

So... how about /proc/sys/vm/, umm.

<looks at inbox, brain explodes>

OK, I give up.  Please see if you can think of something less confusing
which involves no negations?

Thanks.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* dirty highmem calculation sysctl name (Was: [PATCH 1/1] mm: add dirty_highmem option)
  2007-11-27  5:53                                                 ` Andrew Morton
@ 2007-11-27 12:10                                                   ` Bron Gondwana
  2007-11-27 13:06                                                     ` [PATCH] mm/page-writeback - highmem_is_dirtyable option (replaces dirty_highmem patch) Bron Gondwana
  0 siblings, 1 reply; 268+ messages in thread
From: Bron Gondwana @ 2007-11-27 12:10 UTC (permalink / raw)
  To: Andrew Morton
  Cc: Bron Gondwana, Linus Torvalds, Peter Zijlstra, Christian Kujau,
	Linux Kernel Mailing List, Rob Mueller

On Mon, Nov 26, 2007 at 09:53:15PM -0800, Andrew Morton wrote:
> On Tue, 27 Nov 2007 16:24:24 +1100 "Bron Gondwana" <brong@fastmail.fm> wrote:
> 
> > On Mon, 26 Nov 2007 20:54:28 -0800, "Andrew Morton" <akpm@linux-foundation.org> said:
> > > On Thu, 22 Nov 2007 14:42:04 +1100 Bron Gondwana <brong@fastmail.fm>
> > > wrote:
> > > 
> > > >  /*
> > > > + * free highmem will not be subtracted from the total free memory
> > > > + * for calculating free ratios if vm_dirty_highmem is true
> > > > + */
> > > > +int vm_dirty_highmem;
> > > 
> > > One would expect that setting dirty_highmem to true would cause highmem
> > > to
> > > be accounted in dirty-memory calculations.  However with this change
> > > reality is in fact the inverse of that.
> > > 
> > > So how about this?
> > 
> > Actually, I'm confused now.  Maybe I chose a bad name to begin with.
> > Does it mean "I am allowed to dirty high memory" or "my high memory
> > will be dirty if this is on"?
> 
> But we're always allowed to dirty highmem - there'd be no point in having
> it otherwise.  Hence the term dirty_highmem is confusing.
> 
> umm, really you want
> /proc/sys/vm/dont-account-highmem-in-dirty-memory-calculations, only
> shorter.
> 
> Do you agree?

I still read dirty_highmem as:

/proc/sys/vm/do-account-highmem-in-dirty-memory-calculations

... so we're still talking one negative apart!
 
> If so, then it's still not a very pleasing interface - setting something to
> "true" to disable a particular piece of kernel behaviour implies a single
> negation which we don't really need.

Well, the particular piece of kernel behaviour is already a negative:

 "decrease the amount of memory allowed to get dirty so we never dirty
  more than a percentage of available lowmem"

So what this flag is saying is:

 "DON'T decrease the amount of memory allowed to get dirty down to just
  the lowmem - dirty a percentage of total available including highmem"

As Linus said - the alternative of allowing more than 100% of lowmem
to be dirty is just plain too wierd, hence this approach of allowing
an option to turn off the new restriction that appeared since 2.6.16.

> It would be simpler to have
> /proc/sys/vm/do-account-highmem-in-dirty-memory-calculations,
> defaulting to "true" - this has no negations.

No, that's not true.  The whole point is that between 2.6.16 and
2.6.20 the kernel behaviour changed.  It currently doesn't count
highmem in dirty memory calculations, which is why the memory pressure
appears to be so great when actually there's still 4Gb of unused
memory in the box.

/proc/sys/vm/do-account-highmem-in-dirty-memory-calculations would
default to "false" to get the current behaviour post-2.6.16 kernels.

Setting a flag to make it true would stop the kernel subtracting 
highmem from the available count, giving the "old" behaviour of
allowing a percentage of all the memory in the system to be dirty
before forcing writeback.

> So... how about /proc/sys/vm/, umm.
> 
> <looks at inbox, brain explodes>
> 
> OK, I give up.  Please see if you can think of something less confusing
> which involves no negations?

I've spent a while thinking about this, and looking at the code.

I think this might be slightly clearer:


/proc/sys/vm/highmem_is_dirtyable - defaults to false


Here's how it would look in the code:

static unsigned long determine_dirtyable_memory(void)
{
        unsigned long x;

        x = global_page_state(NR_FREE_PAGES)
                + global_page_state(NR_INACTIVE)
                + global_page_state(NR_ACTIVE);

        if (!vm_highmem_is_dirtyable)
                x -= highmem_dirtyable_memory(x);

        return x + 1; /* Ensure that we never return 0 */
}


I think that's very clear.

"Unless highmem is dirtyable, subtract the otherwise dirtyable
 pages from the total dirtyable memory count if they are in
 highmem"

Or without negatives:

"If highmem is dirtyable then include highmem pages in the
 total dirtyable memory count"

Unfortunately this isn't expressed without negatives in the
code because it's easier (I presume without looking at all the
different zones on a cruddy piece of old i386) to add up the 
total and remove the pages in the HIGHMEM zone than to add up
all the non-HIGHMEM zones separately.


Does that suit you?  Does my explaination make sense?

Would you like me to re-submit the patch based on this?  I'm
certainly not happy with dirty_highmem as it is now in mm
because it looks backwards and unclear to me.

Bron.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* [PATCH] mm/page-writeback - highmem_is_dirtyable option (replaces dirty_highmem patch)
  2007-11-27 12:10                                                   ` dirty highmem calculation sysctl name (Was: [PATCH 1/1] mm: add dirty_highmem option) Bron Gondwana
@ 2007-11-27 13:06                                                     ` Bron Gondwana
  0 siblings, 0 replies; 268+ messages in thread
From: Bron Gondwana @ 2007-11-27 13:06 UTC (permalink / raw)
  To: Andrew Morton, Linus Torvalds, Peter Zijlstra, Christian Kujau,
	Linux Kernel Mailing List, Rob Mueller

On Tue, Nov 27, 2007 at 11:10:28PM +1100, Bron Gondwana wrote:
> On Mon, Nov 26, 2007 at 09:53:15PM -0800, Andrew Morton wrote:
> > umm, really you want
> > /proc/sys/vm/dont-account-highmem-in-dirty-memory-calculations, only
> > shorter.
> > 
> > Do you agree?
> 
> I still read dirty_highmem as:
> 
> /proc/sys/vm/do-account-highmem-in-dirty-memory-calculations
> 
> ... so we're still talking one negative apart!
> 
> > It would be simpler to have
> > /proc/sys/vm/do-account-highmem-in-dirty-memory-calculations,
> > defaulting to "true" - this has no negations.
> 
> No, that's not true.  The whole point is that between 2.6.16 and
> 2.6.20 the kernel behaviour changed.  It currently doesn't count
> highmem in dirty memory calculations, which is why the memory pressure
> appears to be so great when actually there's still 4Gb of unused
> memory in the box.
> 
> > OK, I give up.  Please see if you can think of something less confusing
> > which involves no negations?
> 
> I think this might be slightly clearer:
> 
> /proc/sys/vm/highmem_is_dirtyable - defaults to false
> 
> [ ... ]
> 
> Would you like me to re-submit the patch based on this?  I'm
> certainly not happy with dirty_highmem as it is now in mm
> because it looks backwards and unclear to me.

Well, it was quick enough to just do - here's the patch.  I've
also updated the documentation a bit to clarify the intention and
the reasons why you might want to use it (based in part on the 
comments to the original change that made highmem uncountable for
dirtyness purposes)

Tested and applied against 2.6.23.9 (our build script makes Debian
packages from a clean unpack of kernel major plus patch minor plus
svn checkout of out quilt series and apply regardless, so it was
just as easy to bump the version number while I was at it).

Builds, boots, passes a quick run of the test program I used last
time around.

Bron.

Add vm.highmem_is_dirtyable toggle

A 32 bit machine with HIGHMEM64 enabled running DCC has an MMAPed file
of approximately 2Gb size which contains a hash format that is written
randomly by the dbclean process.  On 2.6.16 this process took a few
minutes.  With lowmem only accounting of dirty ratios, this takes about
12 hours of 100% disk IO, all random writes.

This patch includes some code cleanup from Linus and a toggle in
/proc/sys/vm/highmem_is_dirtyable which can be set to 1 to add the 
highmem back to the total available memory count.

Signed-off-by: Bron Gondwana <brong@fastmail.fm>
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/mm/page-writeback.c
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/mm/page-writeback.c	2007-11-21 21:58:20.000000000 -0500
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/mm/page-writeback.c	2007-11-27 07:27:51.000000000 -0500
@@ -70,6 +70,12 @@
 int dirty_background_ratio = 5;
 
 /*
+ * free highmem will not be subtracted from the total free memory
+ * for calculating free ratios if vm_highmem_is_dirtyable is true
+ */
+int vm_highmem_is_dirtyable;
+
+/*
  * The generator of dirty data starts writeback at this percentage
  */
 int vm_dirty_ratio = 10;
@@ -153,7 +159,10 @@
 	x = global_page_state(NR_FREE_PAGES)
 		+ global_page_state(NR_INACTIVE)
 		+ global_page_state(NR_ACTIVE);
-	x -= highmem_dirtyable_memory(x);
+
+	if (!vm_highmem_is_dirtyable)
+		x -= highmem_dirtyable_memory(x);
+
 	return x + 1;	/* Ensure that we never return 0 */
 }
 
@@ -163,20 +172,12 @@
 {
 	int background_ratio;		/* Percentages */
 	int dirty_ratio;
-	int unmapped_ratio;
 	long background;
 	long dirty;
 	unsigned long available_memory = determine_dirtyable_memory();
 	struct task_struct *tsk;
 
-	unmapped_ratio = 100 - ((global_page_state(NR_FILE_MAPPED) +
-				global_page_state(NR_ANON_PAGES)) * 100) /
-					available_memory;
-
 	dirty_ratio = vm_dirty_ratio;
-	if (dirty_ratio > unmapped_ratio / 2)
-		dirty_ratio = unmapped_ratio / 2;
-
 	if (dirty_ratio < 5)
 		dirty_ratio = 5;
 
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/include/linux/writeback.h
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/include/linux/writeback.h	2007-10-09 16:31:38.000000000 -0400
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/include/linux/writeback.h	2007-11-27 07:22:17.000000000 -0500
@@ -95,6 +95,7 @@
 extern int vm_dirty_ratio;
 extern int dirty_writeback_interval;
 extern int dirty_expire_interval;
+extern int vm_highmem_is_dirtyable;
 extern int block_dump;
 extern int laptop_mode;
 
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/kernel/sysctl.c
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/kernel/sysctl.c	2007-10-09 16:31:38.000000000 -0400
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/kernel/sysctl.c	2007-11-27 07:26:43.000000000 -0500
@@ -776,6 +776,7 @@
 /* Constants for minimum and maximum testing in vm_table.
    We use these as one-element integer vectors. */
 static int zero;
+static int one = 1;
 static int two = 2;
 static int one_hundred = 100;
 
@@ -1066,6 +1067,19 @@
 		.extra1		= &zero,
 	},
 #endif
+#ifdef CONFIG_HIGHMEM
+	{
+		.ctl_name	= CTL_UNNUMBERED,
+		.procname	= "highmem_is_dirtyable",
+		.data		= &vm_highmem_is_dirtyable,
+		.maxlen		= sizeof(vm_highmem_is_dirtyable),
+		.mode		= 0644,
+		.proc_handler	= &proc_dointvec_minmax,
+		.strategy	= &sysctl_intvec,
+		.extra1		= &zero,
+		.extra2		= &one,
+	},
+#endif
 /*
  * NOTE: do not add new entries to this table unless you have read
  * Documentation/sysctl/ctl_unnumbered.txt
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/filesystems/proc.txt
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/Documentation/filesystems/proc.txt	2007-10-09 16:31:38.000000000 -0400
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/filesystems/proc.txt	2007-11-27 07:21:22.000000000 -0500
@@ -1253,6 +1253,21 @@
 Data which has been dirty in-memory for longer than this interval will be
 written out next time a pdflush daemon wakes up.
 
+highmem_is_dirtyable
+--------------------
+
+Only present if CONFIG_HIGHMEM is set.
+
+This defaults to 0 (false), meaning that the ratios set above are calculated
+as a percentage of lowmem only.  This protects against excessive scanning
+in page reclaim, swapping and general VM distress.
+
+Setting this to 1 can be useful on 32 bit machines where you want to make
+random changes within an MMAPed file that is larger than your available
+lowmem without causing large quantities of random IO.  Is is safe if the
+behavior of all programs running on the machine is known and memory will
+not be otherwise stressed.
+
 legacy_va_layout
 ----------------
 
Index: linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/sysctl/vm.txt
===================================================================
--- linux-2.6.23.8-reiserfix-fai-vmdirty.orig/Documentation/sysctl/vm.txt	2007-10-09 16:31:38.000000000 -0400
+++ linux-2.6.23.8-reiserfix-fai-vmdirty/Documentation/sysctl/vm.txt	2007-11-27 07:13:30.000000000 -0500
@@ -22,6 +22,7 @@
 - dirty_background_ratio
 - dirty_expire_centisecs
 - dirty_writeback_centisecs
+- highmem_is_dirtyable   (only if CONFIG_HIGHMEM set)
 - max_map_count
 - min_free_kbytes
 - laptop_mode
@@ -36,10 +37,10 @@
 
 ==============================================================
 
-dirty_ratio, dirty_background_ratio, dirty_expire_centisecs,
-dirty_writeback_centisecs, vfs_cache_pressure, laptop_mode,
-block_dump, swap_token_timeout, drop-caches,
-hugepages_treat_as_movable:
+dirty_ratio, dirty_background_ratio, dirty_expire_centisecs, 
+dirty_writeback_centisecs, highmem_is_dirtyable,
+vfs_cache_pressure, laptop_mode, block_dump, swap_token_timeout,
+drop-caches, hugepages_treat_as_movable:
 
 See Documentation/filesystems/proc.txt
 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 19:36                 ` Ingo Molnar
  2007-11-15 22:23                   ` Mark Lord
@ 2007-11-30 12:56                   ` Jörn Engel
  2007-11-30 13:35                     ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-11-30 12:56 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw

On Thu, 15 November 2007 20:36:12 +0100, Ingo Molnar wrote:
> * Ingo Molnar <mingo@elte.hu> wrote:
> 
> > pick up the latest latency tracer patch from:
> 
> sorry, wrong URLs, the correct links are:
> 
>    http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
>    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c

Don't seem to work with plain 2.6.23:

kernel/sched.c:3384: warning: ‘struct prio_array’ declared inside parameter list
kernel/sched.c:3384: warning: its scope is only this definition or declaration, which is probably not what you want
kernel/sched.c: In function ‘trace_array’:
kernel/sched.c:3391: error: dereferencing pointer to incomplete type
kernel/sched.c:3393: error: dereferencing pointer to incomplete type
kernel/sched.c:3393: error: dereferencing pointer to incomplete type
kernel/sched.c:3396: error: dereferencing pointer to incomplete type
kernel/sched.c:3396: error: dereferencing pointer to incomplete type
kernel/sched.c: In function ‘trace_all_runnable_tasks’:
kernel/sched.c:3407: error: ‘struct rq’ has no member named ‘active’
make[1]: *** [kernel/sched.o] Error 1

And I cannot find a definition of struct prio_array in current git
either.  Is another patch needed?

Jörn

-- 
Time? What's that? Time is only worth what you do with it.
-- Theo de Raadt

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 12:56                   ` Jörn Engel
@ 2007-11-30 13:35                     ` Ingo Molnar
  2007-11-30 13:43                       ` Ingo Molnar
  2007-11-30 15:49                       ` Jörn Engel
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-11-30 13:35 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Thu, 15 November 2007 20:36:12 +0100, Ingo Molnar wrote:
> > * Ingo Molnar <mingo@elte.hu> wrote:
> > 
> > > pick up the latest latency tracer patch from:
> > 
> > sorry, wrong URLs, the correct links are:
> > 
> >    http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
> >    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
> 
> Don't seem to work with plain 2.6.23:
> 
> kernel/sched.c:3384: warning: ‘struct prio_array’ declared inside parameter list
> kernel/sched.c:3384: warning: its scope is only this definition or declaration, which is probably not what you want
> kernel/sched.c: In function ‘trace_array’:
> kernel/sched.c:3391: error: dereferencing pointer to incomplete type
> kernel/sched.c:3393: error: dereferencing pointer to incomplete type
> kernel/sched.c:3393: error: dereferencing pointer to incomplete type
> kernel/sched.c:3396: error: dereferencing pointer to incomplete type
> kernel/sched.c:3396: error: dereferencing pointer to incomplete type
> kernel/sched.c: In function ‘trace_all_runnable_tasks’:
> kernel/sched.c:3407: error: ‘struct rq’ has no member named ‘active’
> make[1]: *** [kernel/sched.o] Error 1
> 
> And I cannot find a definition of struct prio_array in current git
> either.  Is another patch needed?

change that to rt_prio_array in the code.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 13:35                     ` Ingo Molnar
@ 2007-11-30 13:43                       ` Ingo Molnar
  2007-11-30 18:35                         ` Jörn Engel
  2007-11-30 15:49                       ` Jörn Engel
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-30 13:43 UTC (permalink / raw)
  To: J?rn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Ingo Molnar <mingo@elte.hu> wrote:

> > > sorry, wrong URLs, the correct links are:
> > > 
> > >    http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch
> > >    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
> > 
> > Don't seem to work with plain 2.6.23:

could you try this updated version:

  http://redhat.com/~mingo/latency-tracing-patches/latency-tracing-v2.6.24-rc3.combo.patch

does it work any better?

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 13:35                     ` Ingo Molnar
  2007-11-30 13:43                       ` Ingo Molnar
@ 2007-11-30 15:49                       ` Jörn Engel
  1 sibling, 0 replies; 268+ messages in thread
From: Jörn Engel @ 2007-11-30 15:49 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Fri, 30 November 2007 14:35:46 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> > 
> > kernel/sched.c:3384: warning: ‘struct prio_array’ declared inside parameter list
> > kernel/sched.c:3384: warning: its scope is only this definition or declaration, which is probably not what you want
> > kernel/sched.c: In function ‘trace_array’:
> > kernel/sched.c:3391: error: dereferencing pointer to incomplete type
> > kernel/sched.c:3393: error: dereferencing pointer to incomplete type
> > kernel/sched.c:3393: error: dereferencing pointer to incomplete type
> > kernel/sched.c:3396: error: dereferencing pointer to incomplete type
> > kernel/sched.c:3396: error: dereferencing pointer to incomplete type
> > kernel/sched.c: In function ‘trace_all_runnable_tasks’:
> > kernel/sched.c:3407: error: ‘struct rq’ has no member named ‘active’
> > make[1]: *** [kernel/sched.o] Error 1
> > 
> > And I cannot find a definition of struct prio_array in current git
> > either.  Is another patch needed?
> 
> change that to rt_prio_array in the code.

Solves the prio_array problem, but leaves the non-existing member
active.  I've upgraded to -rc3 and will give your latest patch a whirl.

Jörn

-- 
Write programs that do one thing and do it well. Write programs to work
together. Write programs to handle text streams, because that is a
universal interface.
-- Doug MacIlroy

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 13:43                       ` Ingo Molnar
@ 2007-11-30 18:35                         ` Jörn Engel
  2007-11-30 18:46                           ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-11-30 18:35 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: J?rn Engel, Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Fri, 30 November 2007 14:43:12 +0100, Ingo Molnar wrote:
> 
>   http://redhat.com/~mingo/latency-tracing-patches/latency-tracing-v2.6.24-rc3.combo.patch
> 
> does it work any better?

It compiles.  It boots with a 512M RAM (384M was too little with all
the other debug options on).  But it seems to lock up when running
trace-cmd.  On a rerun it locks up again, but with different output.
Rerun was captured:
http://logfs.org/~joern/trace1.jpg

I should do a couple of runs, but my girlfriend claims realtime priority
for the evening.

Jörn

-- 
Chance favors only the prepared mind.
-- Louis Pasteur

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 18:35                         ` Jörn Engel
@ 2007-11-30 18:46                           ` Ingo Molnar
  2007-12-01 15:16                             ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-11-30 18:46 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Fri, 30 November 2007 14:43:12 +0100, Ingo Molnar wrote:
> > 
> >   http://redhat.com/~mingo/latency-tracing-patches/latency-tracing-v2.6.24-rc3.combo.patch
> > 
> > does it work any better?
> 
> It compiles.  It boots with a 512M RAM (384M was too little with all
> the other debug options on).  But it seems to lock up when running
> trace-cmd.  On a rerun it locks up again, but with different output.

hm, you should decrease MAX_TRACE in kernel/latency_tracing.c from 1 
million to 16K or so. 1 million entries probably depletes lowmem quite 
seriously.

> Rerun was captured:
> http://logfs.org/~joern/trace1.jpg

hm, that looks weird. if you disable CONFIG_PROVE_LOCKING, does that 
improve things? (or just turns a noisy lockup into a silent lockup?)

> I should do a couple of runs, but my girlfriend claims realtime 
> priority for the evening.

yeah, SCHED_IDLE is not generally well received by them.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-15 22:23                   ` Mark Lord
  2007-11-16  5:55                     ` Ingo Molnar
  2007-11-16 18:35                     ` Mark Lord
@ 2007-11-30 20:12                     ` Mark Lord
  2 siblings, 0 replies; 268+ messages in thread
From: Mark Lord @ 2007-11-30 20:12 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Pavel Machek, Thomas Gleixner, len.brown, Andrew Morton,
	linux-kernel, linux-pm, rjw

Mark Lord wrote:
> Ingo Molnar wrote:
>> * Ingo Molnar <mingo@elte.hu> wrote:
>>
>>> pick up the latest latency tracer patch from:
>>
>> sorry, wrong URLs, the correct links are:
>>
>>    
>> http://redhat.com/~mingo/latency-tracing-patches/latency-tracer-v2.6.24-rc2-git5-combo.patch 
>>
>>    http://redhat.com/~mingo/latency-tracing-patches/trace-cmd.c
> ..
> 
> Is there a version of these that works with 2.6.23.1 ?
> 
> I'm not using 2.6.24-* on this machine because:
>  (a) behaviour may be different, and
>  (b) something broke VMware compatibility again.
..

An update:

Ingo's 2.6.23 version of the latency-tracing-patches only lock-up on resume here.

But now that I've hacked vmware to work on 2.6.24,
my notebook is now running the newer kernels.

So now to see if the "strange 1-second pauses" ever happen here,
and if they do I'll patch in Ingo's stuff to try and find out why.

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-11-30 18:46                           ` Ingo Molnar
@ 2007-12-01 15:16                             ` Jörn Engel
  2007-12-01 18:32                               ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-01 15:16 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Fri, 30 November 2007 19:46:25 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> > 
> > It compiles.  It boots with a 512M RAM (384M was too little with all
> > the other debug options on).  But it seems to lock up when running
> > trace-cmd.  On a rerun it locks up again, but with different output.
> 
> hm, you should decrease MAX_TRACE in kernel/latency_tracing.c from 1 
> million to 16K or so. 1 million entries probably depletes lowmem quite 
> seriously.

That's ok.  RAM is cheap.

> > Rerun was captured:
> > http://logfs.org/~joern/trace1.jpg
> 
> hm, that looks weird. if you disable CONFIG_PROVE_LOCKING, does that 
> improve things? (or just turns a noisy lockup into a silent lockup?)

Not much, although the dumps look different now:
http://logfs.org/~joern/trace3.jpg
http://logfs.org/~joern/trace4.jpg

I have to change my qemu setup a little to see the top of those
dumps...

> > I should do a couple of runs, but my girlfriend claims realtime 
> > priority for the evening.
> 
> yeah, SCHED_IDLE is not generally well received by them.

...as soon as more urgent tasks has finished (weekend is over).

Jörn

-- 
It does not matter how slowly you go, so long as you do not stop.
-- Confucius

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-01 15:16                             ` Jörn Engel
@ 2007-12-01 18:32                               ` Ingo Molnar
  2007-12-01 20:47                                 ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-01 18:32 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> > hm, that looks weird. if you disable CONFIG_PROVE_LOCKING, does that 
> > improve things? (or just turns a noisy lockup into a silent lockup?)
> 
> Not much, although the dumps look different now:
> http://logfs.org/~joern/trace3.jpg
> http://logfs.org/~joern/trace4.jpg
> 
> I have to change my qemu setup a little to see the top of those 
> dumps...

btw., if you start qemu like this:

qemu -cdrom ./cdrom.iso -hda ./hda.img -boot c -full-screen -kernel 
~/bzImage -append "root=/dev/hda1 earlyprintk=serial,ttyS0,9600 
console=tty console=ttyS0,9600 enforcing=0 debug"

you'll get the inner kernel's serial console log to qemu's standard 
output. Pretty useful for capturing kernel crashes.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-01 18:32                               ` Ingo Molnar
@ 2007-12-01 20:47                                 ` Jörn Engel
  2007-12-01 20:54                                   ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-01 20:47 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sat, 1 December 2007 19:32:56 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> 
> > I have to change my qemu setup a little to see the top of those 
> > dumps...
> 
> btw., if you start qemu like this:
> 
> qemu -cdrom ./cdrom.iso -hda ./hda.img -boot c -full-screen -kernel 
> ~/bzImage -append "root=/dev/hda1 earlyprintk=serial,ttyS0,9600 
> console=tty console=ttyS0,9600 enforcing=0 debug"
> 
> you'll get the inner kernel's serial console log to qemu's standard 
> output. Pretty useful for capturing kernel crashes.

Almost.  "-serial stdio" was missing.  Much better now.

stopped custom tracer.
BUG: spinlock recursion on CPU#0, sh/953
 lock: c030f280, .magic: dead4ead, .owner: sh/953, .owner_cpu: 0
Pid: 953, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #2
 [<c0103a04>] show_trace_log_lvl+0x35/0x54
 [<c010450a>] show_trace+0x2c/0x2e
 [<c0104e6d>] dump_stack+0x84/0x8a
 [<c01ded7c>] spin_bug+0xa7/0xae
 [<c01def14>] _raw_spin_lock+0x45/0xfa
 [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
 [<c01087e7>] pit_read+0x14/0x99
 [<c0130ee9>] get_monotonic_cycles+0xf/0x2d
 [<c013c0ef>] now+0x2a/0x7c
 [<c013c33b>] ____trace+0x4d/0x1e8
 [<c013dbf3>] __mcount+0x95/0xa6
 [<c010d35c>] mcount+0x14/0x18
 [<c0135a44>] lock_acquired+0xe/0x1d7
 [<c02a02b9>] _spin_lock_irqsave+0x70/0x7a
 [<c01087e7>] pit_read+0x14/0x99
 [<c0130791>] update_wall_time+0x23/0x692
 [<c0121756>] do_timer+0x24/0xb1
 [<c01331fe>] tick_periodic+0x49/0x84
 [<c013325b>] tick_handle_periodic+0x22/0x73
 [<c0106315>] timer_interrupt+0x4f/0x56
 [<c013e2c7>] handle_IRQ_event+0x24/0x4f
 [<c013f44a>] handle_edge_irq+0xb8/0x125
 [<c01054ee>] do_IRQ+0x89/0xa3
 [<c01033df>] common_interrupt+0x23/0x28
 [<c015d924>] vfs_write+0xa6/0x14c
 [<c015df6e>] sys_write+0x4c/0x70
 [<c0102a1f>] syscall_call+0x7/0xb
 =======================

I assume you have the latency tracer working.  If you could send me your
config, I could do a manual config-bisect and see which part of mine
causes the problem.

Jörn

-- 
Admonish your friends privately, but praise them openly.
-- Publilius Syrus

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-01 20:47                                 ` Jörn Engel
@ 2007-12-01 20:54                                   ` Ingo Molnar
  2007-12-01 23:41                                     ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-01 20:54 UTC (permalink / raw)
  To: J??rn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* J??rn Engel <joern@logfs.org> wrote:

> Almost.  "-serial stdio" was missing.  Much better now.
> 
> stopped custom tracer.
> BUG: spinlock recursion on CPU#0, sh/953
>  lock: c030f280, .magic: dead4ead, .owner: sh/953, .owner_cpu: 0
> Pid: 953, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #2
>  [<c0103a04>] show_trace_log_lvl+0x35/0x54
>  [<c010450a>] show_trace+0x2c/0x2e
>  [<c0104e6d>] dump_stack+0x84/0x8a
>  [<c01ded7c>] spin_bug+0xa7/0xae
>  [<c01def14>] _raw_spin_lock+0x45/0xfa
>  [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
>  [<c01087e7>] pit_read+0x14/0x99
>  [<c0130ee9>] get_monotonic_cycles+0xf/0x2d

ah. You should mark pit_read() function as notrace. PIT clocksource is 
rare. (add the 'notrace' word to the function prototype)

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-01 20:54                                   ` Ingo Molnar
@ 2007-12-01 23:41                                     ` Jörn Engel
  2007-12-02  8:56                                       ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-01 23:41 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: J??rn Engel, Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Sat, 1 December 2007 21:54:56 +0100, Ingo Molnar wrote:
> * J??rn Engel <joern@logfs.org> wrote:
> > 
> > stopped custom tracer.
> > BUG: spinlock recursion on CPU#0, sh/953
> >  lock: c030f280, .magic: dead4ead, .owner: sh/953, .owner_cpu: 0
> > Pid: 953, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #2
> >  [<c0103a04>] show_trace_log_lvl+0x35/0x54
> >  [<c010450a>] show_trace+0x2c/0x2e
> >  [<c0104e6d>] dump_stack+0x84/0x8a
> >  [<c01ded7c>] spin_bug+0xa7/0xae
> >  [<c01def14>] _raw_spin_lock+0x45/0xfa
> >  [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
> >  [<c01087e7>] pit_read+0x14/0x99
> >  [<c0130ee9>] get_monotonic_cycles+0xf/0x2d
> 
> ah. You should mark pit_read() function as notrace. PIT clocksource is 
> rare. (add the 'notrace' word to the function prototype)

Hardly a change at all.  Apart from some offsets, this dump is
identical.

stopped custom tracer.
BUG: spinlock recursion on CPU#0, sh/954
 lock: c030f280, .magic: dead4ead, .owner: sh/954, .owner_cpu: 0
Pid: 954, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #3
 [<c0103a04>] show_trace_log_lvl+0x35/0x54
 [<c010450a>] show_trace+0x2c/0x2e
 [<c0104e6d>] dump_stack+0x84/0x8a
 [<c01ded7c>] spin_bug+0xa7/0xae
 [<c01def14>] _raw_spin_lock+0x45/0xfa
 [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
 [<c01087e2>] pit_read+0xf/0x91
 [<c0130ee1>] get_monotonic_cycles+0xf/0x2d
 [<c013c0e7>] now+0x2a/0x7c
 [<c013c333>] ____trace+0x4d/0x1e8
 [<c013dbeb>] __mcount+0x95/0xa6
 [<c010d354>] mcount+0x14/0x18
 [<c0135a3c>] lock_acquired+0xe/0x1d7
 [<c02a02b9>] _spin_lock_irqsave+0x70/0x7a
 [<c01087e2>] pit_read+0xf/0x91
 [<c0130789>] update_wall_time+0x23/0x692
 [<c012174e>] do_timer+0x24/0xb1
 [<c01331f6>] tick_periodic+0x49/0x84
 [<c0133253>] tick_handle_periodic+0x22/0x73
 [<c0106315>] timer_interrupt+0x4f/0x56
 [<c013e2bf>] handle_IRQ_event+0x24/0x4f
 [<c013f442>] handle_edge_irq+0xb8/0x125
 [<c01054ee>] do_IRQ+0x89/0xa3
 [<c01033df>] common_interrupt+0x23/0x28
 [<c010d354>] mcount+0x14/0x18
 [<c0120130>] sysctl_head_finish+0xc/0x33
 [<c0192d64>] proc_sys_write+0x96/0xa0
 [<c015d91c>] vfs_write+0xa6/0x14c
 [<c015df66>] sys_write+0x4c/0x70
 [<c0102a1f>] syscall_call+0x7/0xb
 =======================

Jörn

-- 
Don't worry about people stealing your ideas. If your ideas are any good,
you'll have to ram them down people's throats.
-- Howard Aiken quoted by Ken Iverson quoted by Jim Horning quoted by
   Raph Levien, 1979

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-01 23:41                                     ` Jörn Engel
@ 2007-12-02  8:56                                       ` Ingo Molnar
  2007-12-02 11:31                                         ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02  8:56 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> > ah. You should mark pit_read() function as notrace. PIT clocksource 
> > is rare. (add the 'notrace' word to the function prototype)
> 
> Hardly a change at all.  Apart from some offsets, this dump is 
> identical.
> 
> stopped custom tracer.
> BUG: spinlock recursion on CPU#0, sh/954
>  lock: c030f280, .magic: dead4ead, .owner: sh/954, .owner_cpu: 0
> Pid: 954, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #3
>  [<c0103a04>] show_trace_log_lvl+0x35/0x54
>  [<c010450a>] show_trace+0x2c/0x2e
>  [<c0104e6d>] dump_stack+0x84/0x8a
>  [<c01ded7c>] spin_bug+0xa7/0xae
>  [<c01def14>] _raw_spin_lock+0x45/0xfa
>  [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
>  [<c01087e2>] pit_read+0xf/0x91
>  [<c0130ee1>] get_monotonic_cycles+0xf/0x2d
>  [<c013c0e7>] now+0x2a/0x7c
>  [<c013c333>] ____trace+0x4d/0x1e8
>  [<c013dbeb>] __mcount+0x95/0xa6
>  [<c010d354>] mcount+0x14/0x18
>  [<c0135a3c>] lock_acquired+0xe/0x1d7
>  [<c02a02b9>] _spin_lock_irqsave+0x70/0x7a
>  [<c01087e2>] pit_read+0xf/0x91

hm, it seems lock_acquired() [in kernel/lockdep.c] needs to be marked 
'notrace' too - otherwise we recurse back into pit_read().

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02  8:56                                       ` Ingo Molnar
@ 2007-12-02 11:31                                         ` Jörn Engel
  2007-12-02 12:31                                           ` Jörn Engel
  2007-12-02 13:57                                           ` Ingo Molnar
  0 siblings, 2 replies; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 11:31 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 09:56:08 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> 
> > > ah. You should mark pit_read() function as notrace. PIT clocksource 
> > > is rare. (add the 'notrace' word to the function prototype)
> > 
> > Hardly a change at all.  Apart from some offsets, this dump is 
> > identical.
> > 
> > stopped custom tracer.
> > BUG: spinlock recursion on CPU#0, sh/954
> >  lock: c030f280, .magic: dead4ead, .owner: sh/954, .owner_cpu: 0
> > Pid: 954, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #3
> >  [<c0103a04>] show_trace_log_lvl+0x35/0x54
> >  [<c010450a>] show_trace+0x2c/0x2e
> >  [<c0104e6d>] dump_stack+0x84/0x8a
> >  [<c01ded7c>] spin_bug+0xa7/0xae
> >  [<c01def14>] _raw_spin_lock+0x45/0xfa
> >  [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
> >  [<c01087e2>] pit_read+0xf/0x91
> >  [<c0130ee1>] get_monotonic_cycles+0xf/0x2d
> >  [<c013c0e7>] now+0x2a/0x7c
> >  [<c013c333>] ____trace+0x4d/0x1e8
> >  [<c013dbeb>] __mcount+0x95/0xa6
> >  [<c010d354>] mcount+0x14/0x18
> >  [<c0135a3c>] lock_acquired+0xe/0x1d7
> >  [<c02a02b9>] _spin_lock_irqsave+0x70/0x7a
> >  [<c01087e2>] pit_read+0xf/0x91
> 
> hm, it seems lock_acquired() [in kernel/lockdep.c] needs to be marked 
> 'notrace' too - otherwise we recurse back into pit_read().

This time not even the offsets have changed.  Dump is identical.

Jörn

-- 
Mundie uses a textbook tactic of manipulation: start with some
reasonable talk, and lead the audience to an unreasonable conclusion.
-- Bruce Perens

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 11:31                                         ` Jörn Engel
@ 2007-12-02 12:31                                           ` Jörn Engel
  2007-12-02 13:57                                             ` Ingo Molnar
  2007-12-02 14:46                                             ` Jörn Engel
  2007-12-02 13:57                                           ` Ingo Molnar
  1 sibling, 2 replies; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 12:31 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Ingo Molnar, Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Sun, 2 December 2007 12:31:43 +0100, Jörn Engel wrote:
> 
> This time not even the offsets have changed.  Dump is identical.

After another ten or so notrace annotations throughout the spinlock
code, the latency tracer appears to work.  Not sure how many useful
information is missing through all the annotations, though.

Jörn

-- 
Das Aufregende am Schreiben ist es, eine Ordnung zu schaffen, wo
vorher keine existiert hat.
-- Doris Lessing

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 11:31                                         ` Jörn Engel
  2007-12-02 12:31                                           ` Jörn Engel
@ 2007-12-02 13:57                                           ` Ingo Molnar
  2007-12-02 14:11                                             ` Jörn Engel
  1 sibling, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 13:57 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Sun, 2 December 2007 09:56:08 +0100, Ingo Molnar wrote:
> > * Jörn Engel <joern@logfs.org> wrote:
> > 
> > > > ah. You should mark pit_read() function as notrace. PIT clocksource 
> > > > is rare. (add the 'notrace' word to the function prototype)
> > > 
> > > Hardly a change at all.  Apart from some offsets, this dump is 
> > > identical.
> > > 
> > > stopped custom tracer.
> > > BUG: spinlock recursion on CPU#0, sh/954
> > >  lock: c030f280, .magic: dead4ead, .owner: sh/954, .owner_cpu: 0
> > > Pid: 954, comm: sh Not tainted 2.6.24-rc3-ge1cca7e8-dirty #3
> > >  [<c0103a04>] show_trace_log_lvl+0x35/0x54
> > >  [<c010450a>] show_trace+0x2c/0x2e
> > >  [<c0104e6d>] dump_stack+0x84/0x8a
> > >  [<c01ded7c>] spin_bug+0xa7/0xae
> > >  [<c01def14>] _raw_spin_lock+0x45/0xfa
> > >  [<c02a02b1>] _spin_lock_irqsave+0x68/0x7a
> > >  [<c01087e2>] pit_read+0xf/0x91
> > >  [<c0130ee1>] get_monotonic_cycles+0xf/0x2d
> > >  [<c013c0e7>] now+0x2a/0x7c
> > >  [<c013c333>] ____trace+0x4d/0x1e8
> > >  [<c013dbeb>] __mcount+0x95/0xa6
> > >  [<c010d354>] mcount+0x14/0x18
> > >  [<c0135a3c>] lock_acquired+0xe/0x1d7
> > >  [<c02a02b9>] _spin_lock_irqsave+0x70/0x7a
> > >  [<c01087e2>] pit_read+0xf/0x91
> > 
> > hm, it seems lock_acquired() [in kernel/lockdep.c] needs to be marked 
> > 'notrace' too - otherwise we recurse back into pit_read().
> 
> This time not even the offsets have changed.  Dump is identical.

hm, do you have CONFIG_FRAME_POINTERS=y, i.e. are the dumps reliable?

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 12:31                                           ` Jörn Engel
@ 2007-12-02 13:57                                             ` Ingo Molnar
  2007-12-02 14:46                                             ` Jörn Engel
  1 sibling, 0 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 13:57 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Sun, 2 December 2007 12:31:43 +0100, Jörn Engel wrote:
> > 
> > This time not even the offsets have changed.  Dump is identical.
> 
> After another ten or so notrace annotations throughout the spinlock 
> code, the latency tracer appears to work.  Not sure how many useful 
> information is missing through all the annotations, though.

a few annotations out of thousands of function calls in the kernel it's 
usually not significant.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 13:57                                           ` Ingo Molnar
@ 2007-12-02 14:11                                             ` Jörn Engel
  2007-12-02 15:47                                               ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 14:11 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 14:57:11 +0100, Ingo Molnar wrote:
> 
> hm, do you have CONFIG_FRAME_POINTERS=y, i.e. are the dumps reliable?

I do.  Went through 10odd runs and annotated the function right below
mcount each time.  Seems to work now.

Trouble is that it doesn't solve my real problem at hand.  Something is
causing significant delays when writing to logfs.  Core logfs code is
not running, but may cause whatever other code is running and burning up
all the cpu time.  Wasting 100ms of "qemu-time" to write a single page
happens fairly frequently.

With the latency tracer the problem appears to have become worse.  Now
the loftlockup code triggers quite frequently.  Which makes a bit of
sense, as the problem is a busy CPU, rather than an idle one.

Guess I'll try oprofile or lcov instead.

Jörn

-- 
Joern's library part 5:
http://www.faqs.org/faqs/compression-faq/part2/section-9.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 12:31                                           ` Jörn Engel
  2007-12-02 13:57                                             ` Ingo Molnar
@ 2007-12-02 14:46                                             ` Jörn Engel
  2007-12-02 15:44                                               ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 14:46 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Ingo Molnar, Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Sun, 2 December 2007 13:31:25 +0100, Jörn Engel wrote:
> 
> After another ten or so notrace annotations throughout the spinlock
> code, the latency tracer appears to work.  Not sure how many useful
> information is missing through all the annotations, though.

And here is a patch with the needed annotations.  Looks a bit shabby, as
it was generated though git diff, patcher, interdiff and combinediff.

Jörn

-- 
Joern's library part 10:
http://blogs.msdn.com/David_Gristwood/archive/2004/06/24/164849.aspx

unchanged:
--- a/arch/x86/kernel/i8253.c
+++ b/arch/x86/kernel/i8253.c
@@ -125,7 +125,7 @@ void __init setup_pit_timer(void)
  * to just read by itself. So use jiffies to emulate a free
  * running counter:
  */
-static cycle_t pit_read(void)
+static notrace cycle_t pit_read(void)
 {
 	unsigned long flags;
 	int count;
unchanged:
--- a/kernel/spinlock.c
+++ b/kernel/spinlock.c
@@ -76,7 +76,7 @@ void __lockfunc _read_lock(rwlock_t *lock)
 }
 EXPORT_SYMBOL(_read_lock);
 
-unsigned long __lockfunc _spin_lock_irqsave(spinlock_t *lock)
+unsigned long notrace __lockfunc _spin_lock_irqsave(spinlock_t *lock)
 {
 	unsigned long flags;
 
@@ -341,7 +341,7 @@ void __lockfunc _read_unlock(rwlock_t *lock)
 }
 EXPORT_SYMBOL(_read_unlock);
 
-void __lockfunc _spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
+void notrace __lockfunc _spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
 {
 	spin_release(&lock->dep_map, 1, _RET_IP_);
 	_raw_spin_unlock(lock);
unchanged:
--- a/lib/spinlock_debug.c
+++ b/lib/spinlock_debug.c
@@ -148,7 +148,7 @@ int _raw_spin_trylock(spinlock_t *lock)
 	return ret;
 }
 
-void _raw_spin_unlock(spinlock_t *lock)
+void notrace _raw_spin_unlock(spinlock_t *lock)
 {
 	debug_spin_unlock(lock);
 	__raw_spin_unlock(&lock->raw_lock);
only in patch2:
unchanged:
--- linux/arch/x86/kernel/tsc_32.c
+++ linux-2.6.24-rc3logfs/arch/x86/kernel/tsc_32.c	2007-12-02 15:21:15.000000000 +0100
@@ -92,7 +92,7 @@
 /*
  * Scheduler clock - returns current time in nanosec units.
  */
-unsigned long long native_sched_clock(void)
+unsigned notrace long long native_sched_clock(void)
 {
 	unsigned long long this_offset;
 
only in patch2:
unchanged:
--- linux/kernel/lockdep.c
+++ linux-2.6.24-rc3logfs/kernel/lockdep.c	2007-12-02 15:21:16.000000000 +0100
@@ -139,7 +139,7 @@
 	return i;
 }
 
-static void lock_time_inc(struct lock_time *lt, s64 time)
+static notrace void lock_time_inc(struct lock_time *lt, s64 time)
 {
 	if (time > lt->max)
 		lt->max = time;
@@ -198,7 +198,7 @@
 	memset(class->contention_point, 0, sizeof(class->contention_point));
 }
 
-static struct lock_class_stats *get_lock_stats(struct lock_class *class)
+static notrace struct lock_class_stats *get_lock_stats(struct lock_class *class)
 {
 	return &get_cpu_var(lock_stats)[class - lock_classes];
 }
@@ -208,7 +208,7 @@
 	put_cpu_var(lock_stats);
 }
 
-static void lock_release_holdtime(struct held_lock *hlock)
+static notrace void lock_release_holdtime(struct held_lock *hlock)
 {
 	struct lock_class_stats *stats;
 	s64 holdtime;
@@ -2872,7 +2872,7 @@
 }
 EXPORT_SYMBOL_GPL(lock_contended);
 
-void lock_acquired(struct lockdep_map *lock)
+void notrace lock_acquired(struct lockdep_map *lock)
 {
 	unsigned long flags;
 

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 14:46                                             ` Jörn Engel
@ 2007-12-02 15:44                                               ` Ingo Molnar
  0 siblings, 0 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 15:44 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw, Steven Rostedt


* Jörn Engel <joern@logfs.org> wrote:

> On Sun, 2 December 2007 13:31:25 +0100, Jörn Engel wrote:
> > 
> > After another ten or so notrace annotations throughout the spinlock
> > code, the latency tracer appears to work.  Not sure how many useful
> > information is missing through all the annotations, though.
> 
> And here is a patch with the needed annotations.  Looks a bit shabby, 
> as it was generated though git diff, patcher, interdiff and 
> combinediff.

thanks - the patches applied fine, i've added them to my latency-tracer 
patchqueue. Steve Rostedt might want to pick the fixes up for -rt as 
well.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 14:11                                             ` Jörn Engel
@ 2007-12-02 15:47                                               ` Ingo Molnar
  2007-12-02 19:55                                                 ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 15:47 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> I do.  Went through 10odd runs and annotated the function right below 
> mcount each time.  Seems to work now.
> 
> Trouble is that it doesn't solve my real problem at hand.  Something 
> is causing significant delays when writing to logfs.  Core logfs code 
> is not running, but may cause whatever other code is running and 
> burning up all the cpu time.  Wasting 100ms of "qemu-time" to write a 
> single page happens fairly frequently.
> 
> With the latency tracer the problem appears to have become worse.  Now 
> the loftlockup code triggers quite frequently.  Which makes a bit of 
> sense, as the problem is a busy CPU, rather than an idle one.

well what does the trace say, where do the delays come from? To get a 
quick overview you can make tracing lighter weight by doing:

 echo 0 > /proc/sys/kernel/mcount_enabled
 echo 1 > /proc/sys/kernel/trace_syscalls

(this turns the latency tracer into a "global strace" kind of tracer)

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 15:47                                               ` Ingo Molnar
@ 2007-12-02 19:55                                                 ` Jörn Engel
  2007-12-02 20:07                                                   ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 19:55 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 16:47:46 +0100, Ingo Molnar wrote:
> 
> well what does the trace say, where do the delays come from? To get a 
> quick overview you can make tracing lighter weight by doing:
> 
>  echo 0 > /proc/sys/kernel/mcount_enabled
>  echo 1 > /proc/sys/kernel/trace_syscalls

I mistyped and did 
 echo 1 > /proc/sys/kernel/mcount_enabled

Result looked like a livelock and finally convinced me to abandon the
latency tracer.  Sorry, but it appears to be the right tool for the
wrong job.

Jörn

-- 
They laughed at Galileo.  They laughed at Copernicus.  They laughed at
Columbus. But remember, they also laughed at Bozo the Clown.
-- unknown

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 19:55                                                 ` Jörn Engel
@ 2007-12-02 20:07                                                   ` Ingo Molnar
  2007-12-02 20:30                                                     ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 20:07 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Sun, 2 December 2007 16:47:46 +0100, Ingo Molnar wrote:
> > 
> > well what does the trace say, where do the delays come from? To get a 
> > quick overview you can make tracing lighter weight by doing:
> > 
> >  echo 0 > /proc/sys/kernel/mcount_enabled
> >  echo 1 > /proc/sys/kernel/trace_syscalls
> 
> I mistyped and did 
>  echo 1 > /proc/sys/kernel/mcount_enabled
> 
> Result looked like a livelock and finally convinced me to abandon the 
> latency tracer.  Sorry, but it appears to be the right tool for the 
> wrong job.

hm, we routinely use it in -rt to capture "what on earth is happening" 
incidents. The snippet below is a random snipped from a trace that i've 
just captured, with mcount enabled. It seems to work fine here, with and 
without mcount. (pit clocksource is almost never used, that's why you 
had those early problems.)

oprofile helps if you can reliably reproduce the slowdown in a loop or 
for a long amount of time, with lots of CPU utilization - and then it's 
also lower overhead. The tracer can be used to capture rare or complex 
events, and gives the full flow control and what is happening within the 
kernel.

	Ingo

------------>
  <idle> 0     1D...  811us : sched_clock_idle_sleep_event (acpi_processor_idle)
  <idle> 0     1D...  813us : _spin_lock (sched_clock_idle_sleep_event)
trace-cm 2463  0....  814us : native_flush_tlb_others (flush_tlb_mm)
  <idle> 0     1D...  815us : __update_rq_clock (sched_clock_idle_sleep_event)
trace-cm 2463  0....  817us : _spin_lock (native_flush_tlb_others)
  <idle> 0     1D...  817us+: acpi_cstate_enter (acpi_processor_idle)
trace-cm 2463  0....  820us+: send_IPI_mask_bitmask (native_flush_tlb_others)
trace-cm 2463  0D...  823us+: apic_wait_icr_idle (send_IPI_mask_bitmask)
trace-cm 2463  0....  856us+: up_write (copy_process)
trace-cm 2463  0....  859us+: copy_keys (copy_process)
trace-cm 2463  0....  862us+: copy_namespaces (copy_process)
trace-cm 2463  0....  865us+: copy_thread (copy_process)
trace-cm 2463  0....  868us+: memcpy (copy_thread)
trace-cm 2463  0....  871us+: alloc_pid (copy_process)
trace-cm 2463  0....  874us+: kmem_cache_alloc (alloc_pid)
trace-cm 2463  0....  877us+: _spin_lock_irq (alloc_pid)
trace-cm 2463  0....  880us+: _write_lock_irq (copy_process)
trace-cm 2463  0D...  883us+: _spin_lock (copy_process)
trace-cm 2463  0D...  887us+: recalc_sigpending (copy_process)
trace-cm 2463  0D...  890us+: recalc_sigpending_tsk (recalc_sigpending)
trace-cm 2463  0D...  893us+: attach_pid (copy_process)
trace-cm 2463  0D...  896us+: attach_pid (copy_process)
trace-cm 2463  0D...  899us+: attach_pid (copy_process)
trace-cm 2463  0....  902us+: proc_fork_connector (copy_process)
trace-cm 2463  0....  905us+: wake_up_new_task (do_fork)
trace-cm 2463  0....  908us+: task_rq_lock (wake_up_new_task)
trace-cm 2463  0D...  911us+: _spin_lock (task_rq_lock)
trace-cm 2463  0D...  914us+: update_rq_clock (wake_up_new_task)
trace-cm 2463  0D...  918us+: __update_rq_clock (update_rq_clock)
trace-cm 2463  0D...  921us+: effective_prio (wake_up_new_task)
trace-cm 2463  0D...  924us+: wake_up_new_task <hwclock 2474> (0 0)

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 20:07                                                   ` Ingo Molnar
@ 2007-12-02 20:30                                                     ` Jörn Engel
  2007-12-02 20:45                                                       ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 20:30 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 21:07:22 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> 
> > Result looked like a livelock and finally convinced me to abandon the 
> > latency tracer.  Sorry, but it appears to be the right tool for the 
> > wrong job.
> 
> hm, we routinely use it in -rt to capture "what on earth is happening" 
> incidents. The snippet below is a random snipped from a trace that i've 
> just captured, with mcount enabled. It seems to work fine here, with and 
> without mcount. (pit clocksource is almost never used, that's why you 
> had those early problems.)
> 
> oprofile helps if you can reliably reproduce the slowdown in a loop or 
> for a long amount of time, with lots of CPU utilization - and then it's 
> also lower overhead. The tracer can be used to capture rare or complex 
> events, and gives the full flow control and what is happening within the 
> kernel.

Such a trace would be useful indeed.  But so far the patch has only
given me grief and nothing remotely like useful output.  Maybe I should
simply use the complete -rt patch instead of debugging the broken-out
latency-tracer patch.

Jörn

-- 
Mundie uses a textbook tactic of manipulation: start with some
reasonable talk, and lead the audience to an unreasonable conclusion.
-- Bruce Perens

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 20:30                                                     ` Jörn Engel
@ 2007-12-02 20:45                                                       ` Ingo Molnar
  2007-12-02 21:08                                                         ` Jörn Engel
  2007-12-02 21:10                                                         ` Jörn Engel
  0 siblings, 2 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 20:45 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> > oprofile helps if you can reliably reproduce the slowdown in a loop 
> > or for a long amount of time, with lots of CPU utilization - and 
> > then it's also lower overhead. The tracer can be used to capture 
> > rare or complex events, and gives the full flow control and what is 
> > happening within the kernel.
> 
> Such a trace would be useful indeed.  But so far the patch has only 
> given me grief and nothing remotely like useful output.  Maybe I 
> should simply use the complete -rt patch instead of debugging the 
> broken-out latency-tracer patch.

to capture that trace i did not use -rt, i just patched latest -git 
with:

  http://people.redhat.com/mingo/latency-tracing-patches/latency-tracing-v2.6.24-rc3.combo.patch

(this has your fixes included already)

have done:

  echo 1 > /proc/sys/kernel/mcount_enabled

and have run:

  ./trace-cmd sleep 1 > trace.txt

  http://people.redhat.com/mingo/latency-tracing-patches/trace-cmd.c

to capture a 1 second trace of what the system is doing. I think your 
troubles are due to running it within a qemu guest - that is not a 
typical utilization so you are on unchartered waters.

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 20:45                                                       ` Ingo Molnar
@ 2007-12-02 21:08                                                         ` Jörn Engel
  2007-12-02 21:10                                                         ` Jörn Engel
  1 sibling, 0 replies; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 21:08 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 21:45:59 +0100, Ingo Molnar wrote:
> 
> to capture a 1 second trace of what the system is doing. I think your 
> troubles are due to running it within a qemu guest - that is not a 
> typical utilization so you are on unchartered waters.

Looks like it.  Guess I'll switch to something else for the moment.

Jörn

-- 
Linux is more the core point of a concept that surrounds "open source"
which, in turn, is based on a false concept. This concept is that
people actually want to look at source code.
-- Rob Enderle

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 20:45                                                       ` Ingo Molnar
  2007-12-02 21:08                                                         ` Jörn Engel
@ 2007-12-02 21:10                                                         ` Jörn Engel
  2007-12-02 21:19                                                           ` Ingo Molnar
  1 sibling, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-02 21:10 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 21:45:59 +0100, Ingo Molnar wrote:
> 
> to capture that trace i did not use -rt, i just patched latest -git 
> with:
> 
>   http://people.redhat.com/mingo/latency-tracing-patches/latency-tracing-v2.6.24-rc3.combo.patch
> 
> (this has your fixes included already)
> 
> have done:
> 
>   echo 1 > /proc/sys/kernel/mcount_enabled
> 
> and have run:
> 
>   ./trace-cmd sleep 1 > trace.txt
> 
>   http://people.redhat.com/mingo/latency-tracing-patches/trace-cmd.c
> 
> to capture a 1 second trace of what the system is doing. I think your 
> troubles are due to running it within a qemu guest - that is not a 
> typical utilization so you are on unchartered waters.

Maybe one more thing: can you send me the config you used for the setup
above?  I'd like to know whether qemu or my config is to blame.

Jörn

-- 
Eighty percent of success is showing up.
-- Woody Allen

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 21:10                                                         ` Jörn Engel
@ 2007-12-02 21:19                                                           ` Ingo Molnar
  2007-12-03  0:57                                                             ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Ingo Molnar @ 2007-12-02 21:19 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw

[-- Attachment #1: Type: text/plain, Size: 535 bytes --]


* Jörn Engel <joern@logfs.org> wrote:

> >   ./trace-cmd sleep 1 > trace.txt
> > 
> >   http://people.redhat.com/mingo/latency-tracing-patches/trace-cmd.c
> > 
> > to capture a 1 second trace of what the system is doing. I think 
> > your troubles are due to running it within a qemu guest - that is 
> > not a typical utilization so you are on unchartered waters.
> 
> Maybe one more thing: can you send me the config you used for the 
> setup above?  I'd like to know whether qemu or my config is to blame.

sure - attached.

	Ingo

[-- Attachment #2: config --]
[-- Type: text/plain, Size: 72625 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24-rc3
# Sun Dec  2 22:06:36 2007
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set
# CONFIG_ZONE_DMA32 is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
# CONFIG_TASK_XACCT is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_AUDIT_TREE=y
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=20
# CONFIG_CGROUPS is not set
CONFIG_FAIR_GROUP_SCHED=y
CONFIG_FAIR_USER_SCHED=y
# CONFIG_FAIR_CGROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBD=y
CONFIG_BLK_DEV_IO_TRACE=y
CONFIG_LSF=y
# CONFIG_BLK_DEV_BSG is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_PREEMPT_NOTIFIERS=y

#
# Processor type and features
#
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_X86_VSMP is not set
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
CONFIG_M686=y
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_XADD=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_NR_CPUS=8
# CONFIG_SCHED_SMT is not set
CONFIG_SCHED_MC=y
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_X86_MCE_P4THERMAL is not set
CONFIG_VM86=y
CONFIG_TOSHIBA=m
CONFIG_I8K=m
# CONFIG_X86_REBOOTFIXUPS is not set
CONFIG_MICROCODE=m
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_EFI=y
CONFIG_IRQBALANCE=y
CONFIG_BOOT_IOREMAP=y
# CONFIG_SECCOMP is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
# CONFIG_HIBERNATION is not set
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=y
CONFIG_ACPI_DOCK=m
# CONFIG_ACPI_BAY is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=1999
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
CONFIG_ACPI_SBS=m
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
CONFIG_APM_CPU_IDLE=y
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
# CONFIG_X86_POWERNOW_K6 is not set
CONFIG_X86_POWERNOW_K7=y
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_GX_SUSPMOD is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=y
CONFIG_X86_SPEEDSTEP_SMI=y
CONFIG_X86_P4_CLOCKMOD=m
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
CONFIG_X86_LONGRUN=y
# CONFIG_X86_LONGHAUL is not set
# CONFIG_X86_E_POWERSAVER is not set

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=y
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
# CONFIG_CPU_IDLE is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_K8_NB=y
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=y
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=y
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
CONFIG_I82092=m
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=y
CONFIG_HOTPLUG_PCI=y
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_COMPAQ=m
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
CONFIG_HOTPLUG_PCI_IBM=m
CONFIG_HOTPLUG_PCI_ACPI=m
CONFIG_HOTPLUG_PCI_ACPI_IBM=m
# CONFIG_HOTPLUG_PCI_CPCI is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_MISC=y

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=y
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=y
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m
# CONFIG_TCP_CONG_YEAH is not set
# CONFIG_TCP_CONG_ILLINOIS is not set
CONFIG_DEFAULT_BIC=y
# CONFIG_DEFAULT_CUBIC is not set
# CONFIG_DEFAULT_HTCP is not set
# CONFIG_DEFAULT_VEGAS is not set
# CONFIG_DEFAULT_WESTWOOD is not set
# CONFIG_DEFAULT_RENO is not set
CONFIG_DEFAULT_TCP_CONG="bic"
CONFIG_TCP_MD5SIG=y
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12

#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y

#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m

#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
# CONFIG_IPV6_MIP6 is not set
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_IPV6_SIT=m
CONFIG_IPV6_TUNNEL=m
# CONFIG_IPV6_MULTIPLE_TABLES is not set
CONFIG_NETLABEL=y
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_QUEUE=y
CONFIG_NETFILTER_NETLINK_LOG=y
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_SECMARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
# CONFIG_NF_CT_PROTO_UDPLITE is not set
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
# CONFIG_NETFILTER_XT_MATCH_CONNLIMIT is not set
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
# CONFIG_NETFILTER_XT_MATCH_TIME is not set
# CONFIG_NETFILTER_XT_MATCH_U32 is not set
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m

#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
CONFIG_NF_NAT_AMANDA=m
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
# CONFIG_IP6_NF_MATCH_MH is not set
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m

#
# DECnet: Netfilter Configuration
#
# CONFIG_DECNET_NF_GRABULATOR is not set

#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y

#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
# CONFIG_IP_DCCP_CCID2_DEBUG is not set
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m
# CONFIG_IP_DCCP_CCID3_DEBUG is not set
CONFIG_IP_DCCP_CCID3_RTO=100

#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
# CONFIG_NET_DCCPPROBE is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
CONFIG_TIPC=m
# CONFIG_TIPC_ADVANCED is not set
# CONFIG_TIPC_DEBUG is not set
CONFIG_ATM=m
CONFIG_ATM_CLIP=m
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
# CONFIG_ATM_MPOA is not set
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
CONFIG_DECNET=m
CONFIG_DECNET_ROUTER=y
CONFIG_LLC=y
# CONFIG_LLC2 is not set
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
# CONFIG_LTPC is not set
# CONFIG_COPS is not set
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
CONFIG_WAN_ROUTER=m
CONFIG_NET_SCHED=y

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
# CONFIG_NET_SCH_RR is not set
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
# CONFIG_NET_ACT_NAT is not set
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
# CONFIG_NET_CLS_POLICE is not set
CONFIG_NET_CLS_IND=y
CONFIG_NET_SCH_FIFO=y

#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
CONFIG_TOIM3232_DONGLE=m
CONFIG_LITELINK_DONGLE=m
CONFIG_MA600_DONGLE=m
CONFIG_GIRBIL_DONGLE=m
CONFIG_MCP2120_DONGLE=m
CONFIG_OLD_BELKIN_DONGLE=m
CONFIG_ACT200L_DONGLE=m
# CONFIG_KINGSUN_DONGLE is not set
# CONFIG_KSDAZZLE_DONGLE is not set
# CONFIG_KS959_DONGLE is not set

#
# Old SIR device drivers
#

#
# Old Serial dongle support
#

#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_SIGMATEL_FIR=m
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
CONFIG_ALI_FIR=m
CONFIG_VLSI_FIR=m
CONFIG_VIA_FIR=m
CONFIG_MCS_FIR=m
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=m
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
# CONFIG_BT_HCIUART_LL is not set
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y

#
# Wireless
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y
CONFIG_PARPORT_NOT_PC=y
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
CONFIG_BLK_CPQ_DA=y
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
CONFIG_BLK_DEV_UB=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=16384
CONFIG_BLK_DEV_RAM_BLOCKSIZE=4096
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
CONFIG_IBM_ASM=m
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
CONFIG_TIFM_CORE=m
CONFIG_TIFM_7XX1=m
# CONFIG_ASUS_LAPTOP is not set
# CONFIG_FUJITSU_LAPTOP is not set
CONFIG_MSI_LAPTOP=m
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
# CONFIG_IDE is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=m
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
CONFIG_CHR_DEV_SCH=y

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=m
# CONFIG_SCSI_FC_TGT_ATTRS is not set
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=y
CONFIG_SCSI_SAS_LIBSAS=y
# CONFIG_SCSI_SAS_ATA is not set
# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
CONFIG_SCSI_SRP_ATTRS=m
# CONFIG_SCSI_SRP_TGT_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
# CONFIG_SCSI_7000FASST is not set
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AHA152X=m
CONFIG_SCSI_AHA1542=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=4
CONFIG_AIC7XXX_RESET_DELAY_MS=1000
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC7XXX_OLD=m
CONFIG_SCSI_AIC79XX=y
CONFIG_AIC79XX_CMDS_PER_DEVICE=4
CONFIG_AIC79XX_RESET_DELAY_MS=1000
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC94XX=y
# CONFIG_AIC94XX_DEBUG is not set
# CONFIG_SCSI_DPT_I2O is not set
CONFIG_SCSI_ADVANSYS=m
# CONFIG_SCSI_IN2000 is not set
CONFIG_SCSI_ARCMSR=m
# CONFIG_SCSI_ARCMSR_AER is not set
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_HPTIOP=m
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
CONFIG_SCSI_FUTURE_DOMAIN=m
CONFIG_SCSI_GDTH=m
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
CONFIG_SCSI_INIA100=m
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
# CONFIG_SCSI_NCR53C406A is not set
CONFIG_SCSI_STEX=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
CONFIG_SCSI_QLA_ISCSI=m
CONFIG_SCSI_LPFC=m
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SYM53C416 is not set
CONFIG_SCSI_DC395x=m
CONFIG_SCSI_DC390T=m
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
CONFIG_SCSI_SRP=m
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
CONFIG_SATA_AHCI=y
CONFIG_SATA_SVW=y
CONFIG_ATA_PIIX=y
CONFIG_SATA_MV=y
CONFIG_SATA_NV=y
CONFIG_PDC_ADMA=y
CONFIG_SATA_QSTOR=y
CONFIG_SATA_PROMISE=y
CONFIG_SATA_SX4=y
CONFIG_SATA_SIL=y
CONFIG_SATA_SIL24=y
CONFIG_SATA_SIS=y
CONFIG_SATA_ULI=y
CONFIG_SATA_VIA=y
CONFIG_SATA_VITESSE=y
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ACPI is not set
CONFIG_PATA_ALI=y
CONFIG_PATA_AMD=y
CONFIG_PATA_ARTOP=y
CONFIG_PATA_ATIIXP=y
# CONFIG_PATA_CMD640_PCI is not set
CONFIG_PATA_CMD64X=y
CONFIG_PATA_CS5520=y
CONFIG_PATA_CS5530=y
CONFIG_PATA_CS5535=y
# CONFIG_PATA_CS5536 is not set
CONFIG_PATA_CYPRESS=y
CONFIG_PATA_EFAR=y
CONFIG_ATA_GENERIC=y
CONFIG_PATA_HPT366=y
CONFIG_PATA_HPT37X=y
CONFIG_PATA_HPT3X2N=y
CONFIG_PATA_HPT3X3=y
# CONFIG_PATA_HPT3X3_DMA is not set
# CONFIG_PATA_ISAPNP is not set
CONFIG_PATA_IT821X=y
# CONFIG_PATA_IT8213 is not set
CONFIG_PATA_JMICRON=y
CONFIG_PATA_LEGACY=m
CONFIG_PATA_TRIFLEX=y
CONFIG_PATA_MARVELL=y
CONFIG_PATA_MPIIX=y
CONFIG_PATA_OLDPIIX=y
CONFIG_PATA_NETCELL=y
CONFIG_PATA_NS87410=y
# CONFIG_PATA_NS87415 is not set
CONFIG_PATA_OPTI=y
CONFIG_PATA_OPTIDMA=y
# CONFIG_PATA_PCMCIA is not set
CONFIG_PATA_PDC_OLD=y
CONFIG_PATA_QDI=y
CONFIG_PATA_RADISYS=y
CONFIG_PATA_RZ1000=y
CONFIG_PATA_SC1200=y
CONFIG_PATA_SERVERWORKS=y
CONFIG_PATA_PDC2027X=y
CONFIG_PATA_SIL680=y
CONFIG_PATA_SIS=y
CONFIG_PATA_VIA=y
CONFIG_PATA_WINBOND=y
CONFIG_PATA_WINBOND_VLB=y
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
# CONFIG_DM_MULTIPATH_RDAC is not set
# CONFIG_DM_MULTIPATH_HP is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_UEVENT is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=40
CONFIG_FUSION_CTL=m
CONFIG_FUSION_LAN=m
# CONFIG_FUSION_LOGGING is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set

#
# Controllers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m

#
# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_I2O=m
# CONFIG_I2O_LCT_NOTIFY_ON_CHANGES is not set
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_IFB=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_MACVLAN is not set
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_VETH is not set
CONFIG_NET_SB1000=m
# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
# CONFIG_ICPLUS_PHY is not set
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
# CONFIG_FIXED_MII_1000_FDX is not set
CONFIG_FIXED_MII_AMNT=1
# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
CONFIG_EL3=m
# CONFIG_3C515 is not set
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
# CONFIG_LANCE is not set
CONFIG_NET_VENDOR_SMC=y
# CONFIG_WD80x3 is not set
CONFIG_ULTRA=m
# CONFIG_SMC9194 is not set
# CONFIG_NET_VENDOR_RACAL is not set
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
CONFIG_TULIP_MMIO=y
# CONFIG_TULIP_NAPI is not set
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_PCMCIA_XIRCOM=m
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
CONFIG_NET_ISA=y
# CONFIG_E2100 is not set
CONFIG_EWRK3=m
# CONFIG_EEXPRESS is not set
# CONFIG_EEXPRESS_PRO is not set
# CONFIG_HPLAN_PLUS is not set
# CONFIG_HPLAN is not set
# CONFIG_LP486E is not set
# CONFIG_ETH16I is not set
CONFIG_NE2000=m
# CONFIG_ZNET is not set
# CONFIG_SEEQ8005 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_PCNET32_NAPI=y
CONFIG_AMD8111_ETH=m
CONFIG_AMD8111E_NAPI=y
CONFIG_ADAPTEC_STARFIRE=m
CONFIG_ADAPTEC_STARFIRE_NAPI=y
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
CONFIG_B44=m
CONFIG_B44_PCI_AUTOSELECT=y
CONFIG_B44_PCICORE_AUTOSELECT=y
CONFIG_B44_PCI=y
CONFIG_FORCEDETH=y
CONFIG_FORCEDETH_NAPI=y
# CONFIG_CS89x0 is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=y
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=y
CONFIG_8139TOO=y
CONFIG_8139TOO_PIO=y
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
CONFIG_VIA_RHINE_NAPI=y
# CONFIG_SC92031 is not set
CONFIG_NET_POCKET=y
CONFIG_ATP=m
CONFIG_DE600=m
CONFIG_DE620=m
CONFIG_NETDEV_1000=y
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=y
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_E1000E is not set
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
CONFIG_R8169_NAPI=y
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=y
# CONFIG_SKGE_DEBUG is not set
CONFIG_SKY2=m
# CONFIG_SKY2_DEBUG is not set
# CONFIG_SK98LIN is not set
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=y
CONFIG_BNX2=m
CONFIG_QLA3XXX=m
# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
CONFIG_CHELSIO_T1=m
CONFIG_CHELSIO_T1_1G=y
CONFIG_CHELSIO_T1_NAPI=y
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGBE is not set
CONFIG_IXGB=m
CONFIG_IXGB_NAPI=y
CONFIG_S2IO=m
CONFIG_S2IO_NAPI=y
CONFIG_MYRI10GE=m
CONFIG_NETXEN_NIC=m
# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
CONFIG_TR=y
# CONFIG_IBMTR is not set
CONFIG_IBMOL=m
CONFIG_IBMLS=m
CONFIG_3C359=m
# CONFIG_TMS380TR is not set
# CONFIG_SMCTR is not set

#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_DM9601 is not set
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
# CONFIG_USB_KC2190 is not set
CONFIG_USB_NET_ZAURUS=m
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
CONFIG_PCMCIA_IBMTR=m
# CONFIG_WAN is not set
CONFIG_ATM_DRIVERS=y
# CONFIG_ATM_DUMMY is not set
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
# CONFIG_ATM_ZATM is not set
CONFIG_ATM_NICSTAR=m
# CONFIG_ATM_NICSTAR_USE_SUNI is not set
# CONFIG_ATM_NICSTAR_USE_IDT77105 is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
# CONFIG_ATM_IA is not set
CONFIG_ATM_FORE200E_MAYBE=m
# CONFIG_ATM_FORE200E_PCA is not set
CONFIG_ATM_HE=m
# CONFIG_ATM_HE_USE_SUNI is not set
CONFIG_FDDI=y
# CONFIG_DEFXX is not set
CONFIG_SKFP=m
# CONFIG_HIPPI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
# CONFIG_PPP_BSDCOMP is not set
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
# CONFIG_PPPOL2TP is not set
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLHC=m
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
CONFIG_NET_FC=y
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_ISDN=m
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
# CONFIG_ISDN_PPP_BSDCOMP is not set
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y

#
# ISDN feature submodules
#
CONFIG_ISDN_DIVERSION=m

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
CONFIG_HISAX_NO_SENDCOMPLETE=y
CONFIG_HISAX_NO_LLC=y
CONFIG_HISAX_NO_KEYPAD=y
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
# CONFIG_HISAX_16_0 is not set
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
# CONFIG_HISAX_IX1MICROR2 is not set
CONFIG_HISAX_DIEHLDIVA=y
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
# CONFIG_HISAX_HFCS is not set
CONFIG_HISAX_SEDLBAUER=y
# CONFIG_HISAX_SPORTSTER is not set
# CONFIG_HISAX_MIC is not set
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#
CONFIG_HISAX_SEDLBAUER_CS=m
CONFIG_HISAX_ELSA_CS=m
CONFIG_HISAX_AVM_A1_CS=m
CONFIG_HISAX_TELES_CS=m

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
# CONFIG_HISAX_HFCUSB is not set
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y

#
# Active cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
# CONFIG_GIGASET_M101 is not set
# CONFIG_GIGASET_DEBUG is not set
# CONFIG_GIGASET_UNDOCREQ is not set
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_CAPI_TRACE=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m

#
# CAPI hardware drivers
#
CONFIG_CAPI_AVM=y
# CONFIG_ISDN_DRV_AVMB1_B1ISA is not set
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
# CONFIG_ISDN_DRV_AVMB1_T1ISA is not set
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_POLLDEV=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_KEYBOARD_STOWAWAY=m
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
CONFIG_MOUSE_VSXXXAA=m
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_ANALOG=m
CONFIG_JOYSTICK_A3D=m
CONFIG_JOYSTICK_ADI=m
CONFIG_JOYSTICK_COBRA=m
CONFIG_JOYSTICK_GF2K=m
CONFIG_JOYSTICK_GRIP=m
CONFIG_JOYSTICK_GRIP_MP=m
CONFIG_JOYSTICK_GUILLEMOT=m
CONFIG_JOYSTICK_INTERACT=m
CONFIG_JOYSTICK_SIDEWINDER=m
CONFIG_JOYSTICK_TMDC=m
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
CONFIG_JOYSTICK_DB9=m
CONFIG_JOYSTICK_GAMECON=m
CONFIG_JOYSTICK_TURBOGRAFX=m
CONFIG_JOYSTICK_JOYDUMP=m
# CONFIG_JOYSTICK_XPAD is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_FUJITSU is not set
CONFIG_TOUCHSCREEN_GUNZE=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_MK712=m
CONFIG_TOUCHSCREEN_PENMOUNT=m
CONFIG_TOUCHSCREEN_TOUCHRIGHT=m
CONFIG_TOUCHSCREEN_TOUCHWIN=m
CONFIG_TOUCHSCREEN_UCB1400=m
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_WISTRON_BTNS=m
# CONFIG_INPUT_ATLAS_BTNS is not set
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
CONFIG_MOXA_SMARTIO_NEW=m
# CONFIG_ISI is not set
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_SYNCLINK_GT=m
CONFIG_N_HDLC=m
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
# CONFIG_SERIAL_8250_FOURPORT is not set
# CONFIG_SERIAL_8250_ACCENT is not set
# CONFIG_SERIAL_8250_BOCA is not set
CONFIG_SERIAL_8250_EXAR_ST16C554=m
# CONFIG_SERIAL_8250_HUB6 is not set
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
CONFIG_TIPAR=m
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
CONFIG_HW_RANDOM_GEODE=m
CONFIG_HW_RANDOM_VIA=m
CONFIG_NVRAM=y
CONFIG_RTC=y
CONFIG_DTLK=m
CONFIG_R3964=m
# CONFIG_APPLICOM is not set
CONFIG_SONYPI=m

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=8192
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_TIS=m
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_TCG_INFINEON=m
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
# CONFIG_I2C_SIMTEC is not set
# CONFIG_SCx200_ACB is not set
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
# CONFIG_I2C_TAOS_EVM is not set
CONFIG_I2C_STUB=m
# CONFIG_I2C_TINY_USB is not set
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
CONFIG_I2C_PCA_ISA=m

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
# CONFIG_DS1682 is not set
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
CONFIG_W1=m
CONFIG_W1_CON=y

#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS2490=m
CONFIG_W1_MASTER_DS2482=m

#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2433=m
CONFIG_W1_SLAVE_DS2433_CRC=y
# CONFIG_W1_SLAVE_DS2760 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ABITUGURU=m
# CONFIG_SENSORS_ABITUGURU3 is not set
# CONFIG_SENSORS_AD7418 is not set
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
# CONFIG_SENSORS_ADM1029 is not set
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
# CONFIG_SENSORS_ADT7470 is not set
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
# CONFIG_SENSORS_I5K_AMB is not set
CONFIG_SENSORS_F71805F=m
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
# CONFIG_SENSORS_FSCHMD is not set
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
# CONFIG_SENSORS_CORETEMP is not set
# CONFIG_SENSORS_IBMPEX is not set
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
# CONFIG_SENSORS_LM93 is not set
CONFIG_SENSORS_MAX1619=m
# CONFIG_SENSORS_MAX6650 is not set
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_PC87427=m
CONFIG_SENSORS_SIS5595=m
# CONFIG_SENSORS_DME1737 is not set
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
# CONFIG_SENSORS_THMC50 is not set
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT1211=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
# CONFIG_SENSORS_APPLESMC is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_ADVANTECH_WDT is not set
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
# CONFIG_SC520_WDT is not set
# CONFIG_EUROTECH_WDT is not set
# CONFIG_IB700_WDT is not set
CONFIG_IBMASR=m
# CONFIG_WAFER_WDT is not set
CONFIG_I6300ESB_WDT=m
CONFIG_ITCO_WDT=m
CONFIG_ITCO_VENDOR_SUPPORT=y
# CONFIG_SC1200_WDT is not set
CONFIG_PC87413_WDT=m
# CONFIG_60XX_WDT is not set
# CONFIG_SBC8360_WDT is not set
# CONFIG_CPU5_WDT is not set
# CONFIG_SMSC37B787_WDT is not set
CONFIG_W83627HF_WDT=m
CONFIG_W83697HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
# CONFIG_SBC_EPX_C3_WATCHDOG is not set

#
# ISA-based Watchdog Cards
#
# CONFIG_PCWATCHDOG is not set
# CONFIG_MIXCOMWD is not set
# CONFIG_WDT is not set

#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m

#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=m
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y

#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
CONFIG_DVB_CORE=m
# CONFIG_DVB_CORE_ATTACH is not set
CONFIG_DVB_CAPTURE_DRIVERS=y

#
# Supported SAA7146 based PCI Adapters
#

#
# Supported USB Adapters
#
CONFIG_DVB_USB=m
# CONFIG_DVB_USB_DEBUG is not set
CONFIG_DVB_USB_A800=m
CONFIG_DVB_USB_DIBUSB_MB=m
# CONFIG_DVB_USB_DIBUSB_MB_FAULTY is not set
CONFIG_DVB_USB_DIBUSB_MC=m
CONFIG_DVB_USB_DIB0700=m
CONFIG_DVB_USB_UMT_010=m
CONFIG_DVB_USB_CXUSB=m
# CONFIG_DVB_USB_M920X is not set
# CONFIG_DVB_USB_GL861 is not set
# CONFIG_DVB_USB_AU6610 is not set
CONFIG_DVB_USB_DIGITV=m
CONFIG_DVB_USB_VP7045=m
CONFIG_DVB_USB_VP702X=m
CONFIG_DVB_USB_GP8PSK=m
CONFIG_DVB_USB_NOVA_T_USB2=m
CONFIG_DVB_USB_TTUSB2=m
CONFIG_DVB_USB_DTT200U=m
# CONFIG_DVB_USB_OPERA1 is not set
# CONFIG_DVB_USB_AF9005 is not set
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
CONFIG_DVB_CINERGYT2=m
CONFIG_DVB_CINERGYT2_TUNING=y
CONFIG_DVB_CINERGYT2_STREAM_URB_COUNT=32
CONFIG_DVB_CINERGYT2_STREAM_BUF_SIZE=512
CONFIG_DVB_CINERGYT2_QUERY_INTERVAL=250
CONFIG_DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE=y
CONFIG_DVB_CINERGYT2_RC_QUERY_INTERVAL=100

#
# Supported FlexCopII (B2C2) Adapters
#
CONFIG_DVB_B2C2_FLEXCOP=m
CONFIG_DVB_B2C2_FLEXCOP_PCI=m
CONFIG_DVB_B2C2_FLEXCOP_USB=m
# CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set

#
# Supported BT878 Adapters
#

#
# Supported Pluto2 Adapters
#
CONFIG_DVB_PLUTO2=m

#
# Supported DVB Frontends
#

#
# Customise DVB Frontends
#
# CONFIG_DVB_FE_CUSTOMISE is not set

#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_TDA8083=m
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m
CONFIG_DVB_TDA10086=m

#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB3000MB=m
CONFIG_DVB_DIB3000MC=m
CONFIG_DVB_DIB7000M=m
CONFIG_DVB_DIB7000P=m

#
# DVB-C (cable) frontends
#
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_TDA10023=m
CONFIG_DVB_STV0297=m

#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends
#
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51211=m
CONFIG_DVB_OR51132=m
CONFIG_DVB_BCM3510=m
CONFIG_DVB_LGDT330X=m
# CONFIG_DVB_S5H1409 is not set

#
# Tuners/PLL support
#
CONFIG_DVB_PLL=m
CONFIG_DVB_TDA826X=m
CONFIG_DVB_TDA827X=m
# CONFIG_DVB_TUNER_QT1010 is not set
CONFIG_DVB_TUNER_MT2060=m
CONFIG_DVB_TUNER_MT2266=m
# CONFIG_DVB_TUNER_MT2131 is not set
CONFIG_DVB_TUNER_DIB0070=m

#
# Miscellaneous devices
#
CONFIG_DVB_LNBP21=m
CONFIG_DVB_ISL6421=m
CONFIG_DVB_TUA6100=m
CONFIG_DAB=y
CONFIG_USB_DABUSB=m

#
# Graphics support
#
CONFIG_AGP=y
CONFIG_AGP_ALI=y
CONFIG_AGP_ATI=y
CONFIG_AGP_AMD=y
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
CONFIG_AGP_NVIDIA=y
CONFIG_AGP_SIS=y
CONFIG_AGP_SWORKS=y
CONFIG_AGP_VIA=y
CONFIG_AGP_EFFICEON=y
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=y
# CONFIG_DRM_I830 is not set
CONFIG_DRM_I915=y
CONFIG_DRM_MGA=m
# CONFIG_DRM_SIS is not set
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m
CONFIG_VGASTATE=m
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
CONFIG_FB_DDC=m
CONFIG_FB_CFB_FILLRECT=m
CONFIG_FB_CFB_COPYAREA=m
CONFIG_FB_CFB_IMAGEBLIT=m
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_UVESA is not set
# CONFIG_FB_VESA is not set
# CONFIG_FB_EFI is not set
# CONFIG_FB_IMAC is not set
# CONFIG_FB_HECUBA is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
CONFIG_FB_RIVA=m
# CONFIG_FB_RIVA_I2C is not set
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_RIVA_BACKLIGHT=y
CONFIG_FB_I810=m
CONFIG_FB_I810_GTF=y
CONFIG_FB_I810_I2C=y
# CONFIG_FB_LE80578 is not set
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
CONFIG_FB_INTEL_I2C=y
CONFIG_FB_MATROX=m
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
# CONFIG_FB_RADEON is not set
CONFIG_FB_ATY128=m
CONFIG_FB_ATY128_BACKLIGHT=y
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
# CONFIG_FB_S3 is not set
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
CONFIG_FB_SAVAGE_ACCEL=y
# CONFIG_FB_SIS is not set
CONFIG_FB_NEOMAGIC=m
CONFIG_FB_KYRO=m
CONFIG_FB_3DFX=m
CONFIG_FB_3DFX_ACCEL=y
CONFIG_FB_VOODOO1=m
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_CYBLA is not set
CONFIG_FB_TRIDENT=m
CONFIG_FB_TRIDENT_ACCEL=y
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_CORGI is not set
# CONFIG_BACKLIGHT_PROGEAR is not set

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_HWDEP=y
CONFIG_SND_RAWMIDI=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_SEQ_DUMMY=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=y
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=y
CONFIG_SND_DUMMY=m
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_MTS64 is not set
# CONFIG_SND_SERIAL_U16550 is not set
CONFIG_SND_MPU401=y
# CONFIG_SND_PORTMAN2X4 is not set
CONFIG_SND_SB_COMMON=m

#
# ISA devices
#
# CONFIG_SND_ADLIB is not set
# CONFIG_SND_AD1816A is not set
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_ALS100 is not set
# CONFIG_SND_AZT2320 is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_DT019X is not set
# CONFIG_SND_ES968 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_SC6000 is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_MIRO is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
# CONFIG_SND_WAVEFRONT is not set

#
# PCI devices
#
CONFIG_SND_AD1889=m
# CONFIG_SND_ALS300 is not set
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
CONFIG_SND_EMU10K1=y
CONFIG_SND_EMU10K1X=y
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
# CONFIG_SND_FM801_TEA575X_BOOL is not set
CONFIG_SND_HDA_INTEL=y
# CONFIG_SND_HDA_HWDEP is not set
CONFIG_SND_HDA_CODEC_REALTEK=y
CONFIG_SND_HDA_CODEC_ANALOG=y
CONFIG_SND_HDA_CODEC_SIGMATEL=y
CONFIG_SND_HDA_CODEC_VIA=y
CONFIG_SND_HDA_CODEC_ATIHDMI=y
CONFIG_SND_HDA_CODEC_CONEXANT=y
CONFIG_SND_HDA_CODEC_CMEDIA=y
CONFIG_SND_HDA_CODEC_SI3054=y
CONFIG_SND_HDA_GENERIC=y
# CONFIG_SND_HDA_POWER_SAVE is not set
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=y
# CONFIG_SND_INTEL8X0M is not set
CONFIG_SND_KORG1212=m
CONFIG_SND_KORG1212_FIRMWARE_IN_KERNEL=y
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MAESTRO3_FIRMWARE_IN_KERNEL=y
# CONFIG_SND_MIXART is not set
CONFIG_SND_NM256=m
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m
CONFIG_SND_YMFPCI_FIRMWARE_IN_KERNEL=y
CONFIG_SND_AC97_POWER_SAVE=y
CONFIG_SND_AC97_POWER_SAVE_DEFAULT=0

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
# CONFIG_SND_USB_CAIAQ is not set

#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set

#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set

#
# SoC Audio support for SuperH
#

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=y
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
CONFIG_HID_DEBUG=y
# CONFIG_HIDRAW is not set

#
# USB Input Devices
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
# CONFIG_PANTHERLORD_FF is not set
CONFIG_THRUSTMASTER_FF=y
CONFIG_ZEROPLUS_FF=y
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
CONFIG_USB_U132_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m
# CONFIG_USB_R8A66597_HCD is not set

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
# CONFIG_USB_STORAGE_ISD200 is not set
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_KARMA=y
CONFIG_USB_LIBUSUAL=y

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_MON=y

#
# USB port drivers
#
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
# CONFIG_USB_SERIAL_CH341 is not set
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_OTI6858 is not set
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
# CONFIG_USB_BERRY_CHARGE is not set
CONFIG_USB_LED=m
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
CONFIG_USB_PHIDGET=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETMOTORCONTROL=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TRANCEVIBRATOR=m
# CONFIG_USB_IOWARRIOR is not set
CONFIG_USB_TEST=m

#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set

#
# MMC/SD Card Drivers
#
CONFIG_MMC_BLOCK=m
CONFIG_MMC_BLOCK_BOUNCE=y
# CONFIG_SDIO_UART is not set

#
# MMC/SD Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
# CONFIG_MMC_RICOH_MMC is not set
CONFIG_MMC_WBSD=m
CONFIG_MMC_TIFM_SD=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_USER_MEM=y
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
# CONFIG_INFINIBAND_AMSO1100 is not set
# CONFIG_MLX4_INFINIBAND is not set
CONFIG_INFINIBAND_IPOIB=m
# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
CONFIG_INFINIBAND_IPOIB_DEBUG_DATA=y
CONFIG_INFINIBAND_SRP=m
CONFIG_INFINIBAND_ISER=m
CONFIG_EDAC=y

#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_MM_EDAC=m
CONFIG_EDAC_AMD76X=m
CONFIG_EDAC_E7XXX=m
CONFIG_EDAC_E752X=m
CONFIG_EDAC_I82875P=m
# CONFIG_EDAC_I82975X is not set
# CONFIG_EDAC_I3000 is not set
CONFIG_EDAC_I82860=m
CONFIG_EDAC_R82600=m
# CONFIG_EDAC_I5000 is not set
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
CONFIG_RTC_DRV_DS1307=m
# CONFIG_RTC_DRV_DS1374 is not set
CONFIG_RTC_DRV_DS1672=m
# CONFIG_RTC_DRV_MAX6900 is not set
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_PCF8563=m
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set

#
# SPI RTC drivers
#

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
CONFIG_RTC_DRV_DS1553=m
# CONFIG_RTC_DRV_STK17TA8 is not set
CONFIG_RTC_DRV_DS1742=m
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
CONFIG_RTC_DRV_V3020=m

#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
CONFIG_VIRTUALIZATION=y
CONFIG_KVM=y
CONFIG_KVM_INTEL=y
CONFIG_KVM_AMD=y
# CONFIG_LGUEST is not set

#
# Userspace I/O
#
# CONFIG_UIO is not set

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_EFI_VARS=y
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_DMIID=y

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
CONFIG_GFS2_FS=m
CONFIG_GFS2_FS_LOCKING_NOLOCK=m
CONFIG_GFS2_FS_LOCKING_DLM=m
CONFIG_OCFS2_FS=m
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
CONFIG_GENERIC_ACL=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
CONFIG_AFFS_FS=m
CONFIG_ECRYPT_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
CONFIG_EFS_FS=m
CONFIG_CRAMFS=m
CONFIG_VXFS_FS=m
# CONFIG_HPFS_FS is not set
CONFIG_QNX4FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_XPRT_RDMA=m
# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
# CONFIG_LDM_PARTITION is not set
CONFIG_SGI_PARTITION=y
# CONFIG_ULTRIX_PARTITION is not set
CONFIG_SUN_PARTITION=y
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
CONFIG_DLM=m
CONFIG_DLM_DEBUG=y
CONFIG_INSTRUMENTATION=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y
# CONFIG_MARKERS is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
CONFIG_EVENT_TRACE=y
CONFIG_FUNCTION_TRACE=y
# CONFIG_WAKEUP_TIMING is not set
# CONFIG_CRITICAL_IRQSOFF_TIMING is not set
CONFIG_MCOUNT=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
CONFIG_FRAME_POINTER=y
# CONFIG_FORCED_INLINING is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SAMPLES is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_RODATA=y
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=y
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_SECURITY_ROOTPLUG is not set
CONFIG_SECURITY_SELINUX=y
CONFIG_SECURITY_SELINUX_BOOTPARAM=y
CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1
CONFIG_SECURITY_SELINUX_DISABLE=y
CONFIG_SECURITY_SELINUX_DEVELOP=y
CONFIG_SECURITY_SELINUX_AVC_STATS=y
CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1
# CONFIG_SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT is not set
# CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_WP512=y
CONFIG_CRYPTO_TGR192=y
CONFIG_CRYPTO_GF128MUL=y
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=y
# CONFIG_CRYPTO_XTS is not set
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_TWOFISH_COMMON=y
# CONFIG_CRYPTO_TWOFISH_586 is not set
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_AES_586 is not set
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_KHAZAD=y
CONFIG_CRYPTO_ANUBIS=y
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_CRYPTO_CRC32C=y
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
# CONFIG_CRYPTO_AUTHENC is not set
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=m
CONFIG_CRYPTO_DEV_PADLOCK_SHA=m
CONFIG_CRYPTO_DEV_GEODE=m

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=y
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_CHECK_SIGNATURE=y

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-02 21:19                                                           ` Ingo Molnar
@ 2007-12-03  0:57                                                             ` Jörn Engel
  2007-12-04  0:06                                                               ` Jörn Engel
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-03  0:57 UTC (permalink / raw)
  To: Ingo Molnar
  Cc: Jörn Engel, Mark Lord, Pavel Machek, Mark Lord,
	Thomas Gleixner, len.brown, Andrew Morton, linux-kernel,
	linux-pm, rjw

On Sun, 2 December 2007 22:19:00 +0100, Ingo Molnar wrote:
> * Jörn Engel <joern@logfs.org> wrote:
> 
> > Maybe one more thing: can you send me the config you used for the 
> > setup above?  I'd like to know whether qemu or my config is to blame.
> 
> sure - attached.

After an eternity of compile time, this config does generate some useful
output.  qemu is not to blame.

Jörn

-- 
Joern's library part 9:
http://www.scl.ameslab.gov/Publications/Gus/TwelveWays.html

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-03  0:57                                                             ` Jörn Engel
@ 2007-12-04  0:06                                                               ` Jörn Engel
  2007-12-04  9:34                                                                 ` Ingo Molnar
  0 siblings, 1 reply; 268+ messages in thread
From: Jörn Engel @ 2007-12-04  0:06 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Ingo Molnar, Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner,
	len.brown, Andrew Morton, linux-kernel, linux-pm, rjw

On Mon, 3 December 2007 01:57:02 +0100, Jörn Engel wrote:
> 
> After an eternity of compile time, this config does generate some useful
> output.  qemu is not to blame.

Or is it?  The output definitely looks suspicious.  Large amounts of
code get processed within a microsecond, while update_wall_time()
appears to cause huge delays every time it is called:
http://logfs.org/~joern/trace

Does this output make sense or does it rather indicate some sloppiness
wrt. time in the qemu virtual machine?

Jörn

-- 
tglx1 thinks that joern should get a (TM) for "Thinking Is Hard"
-- Thomas Gleixner

^ permalink raw reply	[flat|nested] 268+ messages in thread

* Re: [BUG] Strange 1-second pauses during Resume-from-RAM
  2007-12-04  0:06                                                               ` Jörn Engel
@ 2007-12-04  9:34                                                                 ` Ingo Molnar
  0 siblings, 0 replies; 268+ messages in thread
From: Ingo Molnar @ 2007-12-04  9:34 UTC (permalink / raw)
  To: Jörn Engel
  Cc: Mark Lord, Pavel Machek, Mark Lord, Thomas Gleixner, len.brown,
	Andrew Morton, linux-kernel, linux-pm, rjw


* Jörn Engel <joern@logfs.org> wrote:

> On Mon, 3 December 2007 01:57:02 +0100, Jörn Engel wrote:
> > 
> > After an eternity of compile time, this config does generate some useful
> > output.  qemu is not to blame.
> 
> Or is it?  The output definitely looks suspicious.  Large amounts of 
> code get processed within a microsecond, while update_wall_time() 
> appears to cause huge delays every time it is called: 
> http://logfs.org/~joern/trace
> 
> Does this output make sense or does it rather indicate some sloppiness 
> wrt. time in the qemu virtual machine?

not sure. It could be qemu being scheduled away? You could try to run 
qemu with nice -20 or so, to avoid getting preempted. If time lapses 
like this still show up:

 trace-cm 434   0D.h. 1008us!: do_timer (tick_periodic)
 trace-cm 434   0D.h. 1972us+: update_wall_time (do_timer)

 trace-cm 434   0D.h. 1008us!: do_timer (tick_periodic)
 trace-cm 434   0D.h. 1972us+: update_wall_time (do_timer)

then that could indicate a timekeeping weirdness, OR it could mean that 
qemu is simply very slow. (there could be timer hw access between those 
two function calls)

	Ingo

^ permalink raw reply	[flat|nested] 268+ messages in thread

end of thread, other threads:[~2007-12-04  9:35 UTC | newest]

Thread overview: 268+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-11-13  6:42 [BUG] New Kernel Bugs Natalie Protasevich
2007-11-13 11:15 ` Andrew Morton
2007-11-13 11:24   ` Jens Axboe
2007-11-13 11:33   ` Evgeniy Polyakov
2007-11-13 11:39   ` David Miller
2007-11-13 11:49     ` Andrew Morton
2007-11-13 11:58       ` David Miller
2007-11-13 12:12         ` Andrew Morton
2007-11-13 12:32           ` David Miller
2007-11-13 19:02             ` Andrew Morton
2007-11-13 20:00               ` Christian Kujau
2007-11-13 21:04                 ` Andrew Morton
2007-11-13 16:56                   ` Nick Piggin
2007-11-14 19:54                     ` Linus Torvalds
2007-11-14 22:22                       ` Heikki Orsila
2007-11-14 23:05                         ` Linus Torvalds
2007-11-13 21:37                   ` Adrian Bunk
2007-11-13 21:56                   ` Christian Kujau
2007-11-15  4:07                     ` Bron Gondwana
2007-11-15  4:24                       ` Linus Torvalds
2007-11-15  5:25                         ` Bron Gondwana
2007-11-15  5:35                           ` Linus Torvalds
2007-11-15  5:53                             ` Linus Torvalds
2007-11-15 11:50                               ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
2007-11-15 16:32                                 ` Linus Torvalds
2007-11-15 19:40                                   ` Peter Zijlstra
2007-11-15 20:44                                     ` Peter Zijlstra
2007-11-15 20:56                                       ` Linus Torvalds
2007-11-15 20:59                                         ` Peter Zijlstra
2007-11-15 21:12                                           ` Peter Zijlstra
2007-11-15 21:14                                         ` Linus Torvalds
2007-11-15 21:26                                           ` Linus Torvalds
2007-11-15 21:26                                           ` Peter Zijlstra
2007-11-15 21:47                                             ` Linus Torvalds
2007-11-15 22:11                                               ` Chris Friesen
2007-11-15 22:31                                                 ` Linus Torvalds
2007-11-15 22:24                                               ` Rob Mueller
2007-11-18 23:13                                                 ` Daniel Phillips
2007-11-19  3:41                                                   ` Bron Gondwana
2007-11-16  0:48                                               ` Alan Cox
2007-11-21 21:25                                               ` Jan Engelhardt
2007-11-19  3:54                                           ` Bron Gondwana
2007-11-22  3:42                                           ` [PATCH 1/1] mm: add dirty_highmem option Bron Gondwana
2007-11-26 17:53                                             ` Linus Torvalds
2007-11-27  1:30                                               ` Bron Gondwana
2007-11-27  4:54                                             ` Andrew Morton
2007-11-27  5:24                                               ` Bron Gondwana
2007-11-27  5:53                                                 ` Andrew Morton
2007-11-27 12:10                                                   ` dirty highmem calculation sysctl name (Was: [PATCH 1/1] mm: add dirty_highmem option) Bron Gondwana
2007-11-27 13:06                                                     ` [PATCH] mm/page-writeback - highmem_is_dirtyable option (replaces dirty_highmem patch) Bron Gondwana
2007-11-21 23:51                                   ` mmap dirty limits on 32 bit kernels (Was: [BUG] New Kernel Bugs) Bron Gondwana
2007-11-22  2:16                                     ` Bron Gondwana
2007-11-13 19:32             ` [BUG] New Kernel Bugs Russell King
2007-11-13 20:13               ` Adrian Bunk
2007-11-13 23:29                 ` Russell King
2007-11-13 23:38                   ` Andrew Morton
2007-11-13 20:52               ` Andrew Morton
2007-11-13 22:18                 ` Russell King
2007-11-13 22:32                   ` Andrew Morton
2007-11-13 23:09                     ` Russell King
2007-11-13 23:17                       ` Andrew Morton
2007-11-14  1:55                     ` David Miller
2007-11-14  2:27                       ` Andrew Morton
2007-11-14  3:47                         ` David Miller
2007-11-14  8:30                         ` Russell King
2007-11-14  9:55                       ` Russell King
2007-11-14 10:07                         ` David Miller
2007-11-14 11:46                           ` [alsa-devel] " Rene Herman
2007-11-14 11:56                             ` David Miller
2007-11-14 12:01                               ` David Miller
2007-11-14  8:25                                 ` Moderated list (Was: Re: [BUG] New Kernel Bugs) Takashi Iwai
2007-11-14 12:21                                   ` Rene Herman
2007-11-14  9:47                                     ` Takashi Iwai
2007-11-14 23:23                                       ` Moderated list David Miller
2007-11-15  6:09                                         ` Rene Herman
2007-11-14 12:12                                 ` [alsa-devel] [BUG] New Kernel Bugs Rene Herman
2007-11-14 12:09                               ` Rene Herman
2007-11-15  4:16                             ` Bron Gondwana
2007-11-15  5:59                               ` Rene Herman
2007-11-15 12:02                                 ` Bron Gondwana
2007-11-15 12:26                                   ` Rene Herman
2007-11-15 13:00                                     ` Jörn Engel
2007-11-15 14:29                                       ` Rene Herman
2007-11-15 13:17                                 ` Olivier Galibert
2007-11-15  9:34                                   ` Takashi Iwai
2007-11-14 19:44                           ` Russell King
2007-11-16 22:16                           ` Use *poof* for linux-omap (Was: [BUG] New Kernel Bugs) Tony Lindgren
2007-11-17  0:45                             ` Use *poof* for linux-omap David Miller
2007-11-18 20:01                               ` Tony Lindgren
2007-11-14  5:56                   ` [BUG] New Kernel Bugs Sam Ravnborg
2007-11-14  5:59                     ` Sam Ravnborg
2007-11-14  6:13                     ` David Miller
2007-11-13 13:40           ` Ingo Molnar
2007-11-13 14:08             ` Mark Lord
2007-11-13 15:24               ` Giacomo A. Catenazzi
2007-11-13 15:57                 ` Ray Lee
2007-11-13 17:01                   ` Adrian Bunk
2007-11-13 17:50                     ` Romano Giannetti
2007-11-13 22:03                       ` Frans Pop
2007-11-13 15:52               ` Benoit Boissinot
2007-11-13 16:49                 ` Ingo Molnar
2007-11-13 17:13                 ` Theodore Tso
2007-11-13 17:30                   ` Alan Cox
2007-11-13 17:33                   ` Larry Finger
2007-11-13 18:55                     ` Theodore Tso
2007-11-13 20:07                       ` Larry Finger
2007-11-13 17:56                   ` Adrian Bunk
2007-11-13 18:57                     ` Gabriel C
2007-11-14  0:41                       ` Denys Vlasenko
2007-11-14  0:39                     ` Denys Vlasenko
2007-11-14  7:27                       ` Adrian Bunk
2007-11-14  7:46                         ` Denys Vlasenko
2007-11-14 13:30                           ` Matthew Wilcox
2007-11-14 13:35                             ` Hannes Reinecke
2007-11-14 21:39                               ` Denys Vlasenko
2007-11-14 21:58                                 ` Gabriel C
2007-11-14 18:27                           ` Kok, Auke
2007-11-14 16:55                     ` Jan Evert van Grootheest
2007-11-14 23:23                   ` Daniel Barkalow
2007-11-15 15:30                     ` Theodore Tso
2007-11-15 16:19                       ` Daniel Barkalow
2007-11-16  8:20                         ` Romano Giannetti
2007-11-16 18:20                           ` Daniel Barkalow
2007-11-16 19:46                             ` Theodore Tso
2007-11-17 12:20                               ` Adrian Bunk
2007-11-18 18:01                                 ` Theodore Tso
2007-11-13 16:46               ` Ingo Molnar
2007-11-13 17:50                 ` Mark Lord
2007-11-13 18:12                   ` Adrian Bunk
2007-11-13 18:18                     ` Mark Lord
2007-11-13 18:36                       ` Adrian Bunk
2007-11-13 18:47                         ` Mark Lord
2007-11-13 19:04                           ` Adrian Bunk
2007-11-13 19:12                             ` Mark Lord
2007-11-13 19:30                               ` Adrian Bunk
2007-11-13 19:46                                 ` Russell King
2007-11-13 20:04                                   ` Adrian Bunk
2007-11-13 19:26                             ` Mark Lord
2007-11-13 20:00                               ` Adrian Bunk
2007-11-13 20:13                                 ` Mark Lord
2007-11-13 21:20                                   ` Adrian Bunk
2007-11-13 21:12                                 ` Alan Cox
2007-11-14  0:52                                   ` Chuck Ebbert
2007-11-14  1:11                                     ` Stephen Hemminger
2007-11-14  2:10                                       ` Andrew Morton
2007-11-14  1:10                       ` David Miller
2007-11-14  1:18                         ` Peter Stuge
2007-11-13 18:17                   ` Peter Zijlstra
2007-11-13 18:39                   ` Matthew Wilcox
2007-11-13 18:43                     ` Mark Lord
2007-11-13 18:49                       ` Matthew Wilcox
2007-11-13 18:54                         ` Mark Lord
2007-11-13 22:09                           ` Rafael J. Wysocki
2007-11-14 14:30                           ` Ingo Molnar
2007-11-14 14:49                             ` Larry Finger
2007-11-18 12:44                   ` size of git repository (was Re: [BUG] New Kernel Bugs) Pavel Machek
2007-11-18 12:58                     ` Rene Herman
2007-11-18 14:35                       ` James Bottomley
2007-11-18 15:19                         ` Rene Herman
2007-11-18 14:56                     ` Ingo Molnar
2007-11-19  4:43                       ` Willy Tarreau
2007-11-13 19:37               ` [BUG] New Kernel Bugs Russell King
2007-11-13 20:18                 ` Mark Lord
2007-11-13 21:33                   ` Jörn Engel
2007-11-13 21:56                     ` Andrew Morton
2007-11-13 22:24                       ` Jörn Engel
2007-11-13 22:43                         ` Andrew Morton
2007-11-13 22:29                     ` Mark Lord
2007-11-13 23:40                   ` Russell King
2007-11-14  1:56                     ` David Miller
2007-11-14  0:34               ` Denys Vlasenko
2007-11-15  3:06                 ` Neil Brown
2007-11-13 16:55             ` Randy Dunlap
2007-11-14 14:08               ` Ingo Molnar
2007-11-14 17:38                 ` Randy Dunlap
2007-11-14 18:23                   ` J. Bruce Fields
2007-11-15  2:50                     ` Neil Brown
2007-11-16  0:05                       ` J. Bruce Fields
2007-11-14 20:16                   ` Ingo Molnar
2007-11-14 20:29                     ` Randy Dunlap
2007-11-14 20:37                       ` Ingo Molnar
2007-11-14 21:05                         ` Randy Dunlap
2007-11-14 19:56                 ` David Miller
2007-11-14 20:09                   ` James Bottomley
2007-11-14 20:54                     ` Ingo Molnar
2007-11-14 20:48                   ` Ingo Molnar
2007-11-14 21:05                     ` david
2007-11-13 11:47   ` Jarek Poplawski
2007-11-13 13:58   ` Mark Lord
2007-11-13 14:18     ` Mark Lord
2007-11-13 16:08       ` Thomas Gleixner
2007-11-13 16:07     ` Thomas Gleixner
2007-11-13 17:47       ` Mark Lord
2007-11-15 16:32         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
2007-11-15 16:49           ` Ray Lee
2007-11-15 16:51             ` Mark Lord
2007-11-15 16:53               ` Mark Lord
2007-11-15 18:14           ` Pavel Machek
2007-11-15 17:31             ` Mark Lord
2007-11-15 19:34               ` Ingo Molnar
2007-11-15 19:36                 ` Ingo Molnar
2007-11-15 22:23                   ` Mark Lord
2007-11-16  5:55                     ` Ingo Molnar
2007-11-16  7:15                       ` Ingo Molnar
2007-11-16  8:21                         ` Ingo Molnar
2007-11-16 11:23                           ` Ingo Molnar
2007-11-16 11:53                             ` Mike Galbraith
2007-11-16 12:43                             ` Ingo Molnar
2007-11-16 12:58                               ` [patch] snd hda suspend latency: shorten codec read Ingo Molnar
2007-11-16 13:31                                 ` Rafael J. Wysocki
2007-11-16 14:21                                 ` Takashi Iwai
2007-11-16 19:06                         ` [BUG] Strange 1-second pauses during Resume-from-RAM Mark Lord
2007-11-16 18:35                     ` Mark Lord
2007-11-30 20:12                     ` Mark Lord
2007-11-30 12:56                   ` Jörn Engel
2007-11-30 13:35                     ` Ingo Molnar
2007-11-30 13:43                       ` Ingo Molnar
2007-11-30 18:35                         ` Jörn Engel
2007-11-30 18:46                           ` Ingo Molnar
2007-12-01 15:16                             ` Jörn Engel
2007-12-01 18:32                               ` Ingo Molnar
2007-12-01 20:47                                 ` Jörn Engel
2007-12-01 20:54                                   ` Ingo Molnar
2007-12-01 23:41                                     ` Jörn Engel
2007-12-02  8:56                                       ` Ingo Molnar
2007-12-02 11:31                                         ` Jörn Engel
2007-12-02 12:31                                           ` Jörn Engel
2007-12-02 13:57                                             ` Ingo Molnar
2007-12-02 14:46                                             ` Jörn Engel
2007-12-02 15:44                                               ` Ingo Molnar
2007-12-02 13:57                                           ` Ingo Molnar
2007-12-02 14:11                                             ` Jörn Engel
2007-12-02 15:47                                               ` Ingo Molnar
2007-12-02 19:55                                                 ` Jörn Engel
2007-12-02 20:07                                                   ` Ingo Molnar
2007-12-02 20:30                                                     ` Jörn Engel
2007-12-02 20:45                                                       ` Ingo Molnar
2007-12-02 21:08                                                         ` Jörn Engel
2007-12-02 21:10                                                         ` Jörn Engel
2007-12-02 21:19                                                           ` Ingo Molnar
2007-12-03  0:57                                                             ` Jörn Engel
2007-12-04  0:06                                                               ` Jörn Engel
2007-12-04  9:34                                                                 ` Ingo Molnar
2007-11-30 15:49                       ` Jörn Engel
2007-11-15 20:27               ` Rafael J. Wysocki
2007-11-18 16:10           ` Mark Lord
2007-11-18 16:21             ` Ingo Molnar
2007-11-18 17:37               ` Mark Lord
2007-11-13 17:54       ` [BUG] New Kernel Bugs Mark Lord
2007-11-13 22:46         ` Thomas Gleixner
2007-11-13 23:37           ` Mark Lord
2007-11-13 18:10       ` Russell King
2007-11-13 18:25         ` Alan Cox
2007-11-13 22:34           ` Russell King
2007-11-15 20:16             ` Ben Dooks
2007-11-13 15:21   ` Bartlomiej Zolnierkiewicz
2007-11-13 15:33   ` James Bottomley
2007-11-13 16:43     ` Randy Dunlap
2007-11-13 17:46     ` Martin Bligh
2007-11-13 18:47       ` Andrew Morton
2007-11-14  5:07       ` David Miller
2007-11-13 15:36   ` Alan Cox
2007-11-13 17:49   ` Jan Kara
2007-11-13 18:04   ` Russell King
2007-11-14 12:46   ` Jiri Kosina
2007-11-14 13:24   ` Pavel Machek
2007-11-14 14:14     ` Fabio Comolli
2007-11-14 19:52     ` Russell King

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).