From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
To: linux-ide@vger.kernel.org
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>,
linux-kernel@vger.kernel.org
Subject: [PATCH 6/8] ide: separate PCI specific init from generic init in ide_pci_setup_ports()
Date: Sun, 06 Jan 2008 18:03:03 +0100 [thread overview]
Message-ID: <20080106170303.6861.43285.sendpatchset@localhost.localdomain> (raw)
In-Reply-To: <20080106170220.6861.4814.sendpatchset@localhost.localdomain>
* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
in ide_hwif_configure().
* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.
* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
+28 bytes
drivers/ide/setup-pci.c | 29 +++++++++++++++++++++--------
1 file changed, 21 insertions(+), 8 deletions(-)
Index: b/drivers/ide/setup-pci.c
===================================================================
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -337,7 +337,8 @@ static int ide_pci_check_iomem(struct pc
* ide_hwif_configure - configure an IDE interface
* @dev: PCI device holding interface
* @d: IDE port info
- * @mate: Paired interface if any
+ * @port: port number
+ * @irq: PCI IRQ
*
* Perform the initial set up for the hardware interface structure. This
* is done per interface port rather than per PCI device. There may be
@@ -346,7 +347,9 @@ static int ide_pci_check_iomem(struct pc
* Returns the new hardware interface structure, or NULL on a failure
*/
-static ide_hwif_t *ide_hwif_configure(struct pci_dev *dev, const struct ide_port_info *d, ide_hwif_t *mate, int port, int irq)
+static ide_hwif_t *ide_hwif_configure(struct pci_dev *dev,
+ const struct ide_port_info *d,
+ unsigned int port, int irq)
{
unsigned long ctl = 0, base = 0;
ide_hwif_t *hwif;
@@ -392,12 +395,7 @@ static ide_hwif_t *ide_hwif_configure(st
hwif->dev = &dev->dev;
hwif->cds = d;
- hwif->channel = port;
- if (mate) {
- hwif->mate = mate;
- mate->mate = hwif;
- }
return hwif;
}
@@ -525,10 +523,25 @@ void ide_pci_setup_ports(struct pci_dev
continue; /* port not enabled */
}
- if ((hwif = ide_hwif_configure(dev, d, mate, port, pciirq)) == NULL)
+ hwif = ide_hwif_configure(dev, d, port, pciirq);
+ if (hwif == NULL)
continue;
*(idx + port) = hwif->index;
+ }
+
+ for (port = 0; port < channels; ++port) {
+ if (*(idx + port) == 0xff)
+ continue;
+
+ hwif = &ide_hwifs[*(idx + port)];
+
+ if (mate) {
+ hwif->mate = mate;
+ mate->mate = hwif;
+ }
+
+ hwif->channel = port;
if (d->init_iops)
d->init_iops(hwif);
next prev parent reply other threads:[~2008-01-06 16:52 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-01-06 17:02 [PATCH 0/8] ide: more IDE probing code rework Bartlomiej Zolnierkiewicz
2008-01-06 17:02 ` [PATCH 1/8] dtc2278: fix ->io_32bit handling Bartlomiej Zolnierkiewicz
2008-01-06 17:02 ` [PATCH 2/8] au1xxx-ide: " Bartlomiej Zolnierkiewicz
2008-01-06 17:02 ` [PATCH 3/8] atiixp/cs5535/scc_pata: fix "idex=ata66" parameter handling Bartlomiej Zolnierkiewicz
2008-01-06 17:02 ` [PATCH 4/8] macide: remove drive->capacity64 quirk Bartlomiej Zolnierkiewicz
2008-01-06 17:02 ` [PATCH 5/8] ide: always set DMA masks in ide_pci_setup_ports() Bartlomiej Zolnierkiewicz
2008-01-29 20:02 ` Sergei Shtylyov
2008-01-06 17:03 ` Bartlomiej Zolnierkiewicz [this message]
2008-01-06 17:03 ` [PATCH 7/8] ide: add struct ide_port_info instances to legacy host drivers Bartlomiej Zolnierkiewicz
2008-01-28 20:28 ` Sergei Shtylyov
2008-02-01 23:35 ` Bartlomiej Zolnierkiewicz
2008-02-11 18:36 ` Russell King
2008-02-10 16:07 ` Atsushi Nemoto
2008-02-10 17:04 ` Bartlomiej Zolnierkiewicz
2008-02-10 23:16 ` Bartlomiej Zolnierkiewicz
2008-02-11 12:01 ` Atsushi Nemoto
2008-01-06 17:03 ` [PATCH 8/8] ide: add ->cable_detect method to ide_hwif_t Bartlomiej Zolnierkiewicz
2008-01-12 20:05 ` Sergei Shtylyov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080106170303.6861.43285.sendpatchset@localhost.localdomain \
--to=bzolnier@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).